diff options
Diffstat (limited to 'drivers/hwmon/lm90.c')
| -rw-r--r-- | drivers/hwmon/lm90.c | 1755 |
1 files changed, 1307 insertions, 448 deletions
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index d1a3da3dd8e..c9ff08dbe10 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -1,63 +1,69 @@ /* * lm90.c - Part of lm_sensors, Linux kernel modules for hardware * monitoring - * Copyright (C) 2003-2006 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2003-2010 Jean Delvare <jdelvare@suse.de> * * Based on the lm83 driver. The LM90 is a sensor chip made by National * Semiconductor. It reports up to two temperatures (its own plus up to * one external one) with a 0.125 deg resolution (1 deg for local - * temperature) and a 3-4 deg accuracy. Complete datasheet can be - * obtained from National's website at: - * http://www.national.com/pf/LM/LM90.html + * temperature) and a 3-4 deg accuracy. * * This driver also supports the LM89 and LM99, two other sensor chips * made by National Semiconductor. Both have an increased remote * temperature measurement accuracy (1 degree), and the LM99 * additionally shifts remote temperatures (measured and limits) by 16 - * degrees, which allows for higher temperatures measurement. The - * driver doesn't handle it since it can be done easily in user-space. - * Complete datasheets can be obtained from National's website at: - * http://www.national.com/pf/LM/LM89.html - * http://www.national.com/pf/LM/LM99.html + * degrees, which allows for higher temperatures measurement. * Note that there is no way to differentiate between both chips. + * When device is auto-detected, the driver will assume an LM99. * * This driver also supports the LM86, another sensor chip made by * National Semiconductor. It is exactly similar to the LM90 except it * has a higher accuracy. - * Complete datasheet can be obtained from National's website at: - * http://www.national.com/pf/LM/LM86.html * * This driver also supports the ADM1032, a sensor chip made by Analog * Devices. That chip is similar to the LM90, with a few differences - * that are not handled by this driver. Complete datasheet can be - * obtained from Analog's website at: - * http://www.analog.com/en/prod/0,2877,ADM1032,00.html - * Among others, it has a higher accuracy than the LM90, much like the - * LM86 does. + * that are not handled by this driver. Among others, it has a higher + * accuracy than the LM90, much like the LM86 does. * * This driver also supports the MAX6657, MAX6658 and MAX6659 sensor - * chips made by Maxim. These chips are similar to the LM86. Complete - * datasheet can be obtained at Maxim's website at: - * http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578 + * chips made by Maxim. These chips are similar to the LM86. * Note that there is no easy way to differentiate between the three - * variants. The extra address and features of the MAX6659 are not - * supported by this driver. These chips lack the remote temperature - * offset feature. + * variants. We use the device address to detect MAX6659, which will result + * in a detection as max6657 if it is on address 0x4c. The extra address + * and features of the MAX6659 are only supported if the chip is configured + * explicitly as max6659, or if its address is not 0x4c. + * These chips lack the remote temperature offset feature. + * + * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and + * MAX6692 chips made by Maxim. These are again similar to the LM86, + * but they use unsigned temperature values and can report temperatures + * from 0 to 145 degrees. * * This driver also supports the MAX6680 and MAX6681, two other sensor * chips made by Maxim. These are quite similar to the other Maxim - * chips. Complete datasheet can be obtained at: - * http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370 - * The MAX6680 and MAX6681 only differ in the pinout so they can be - * treated identically. + * chips. The MAX6680 and MAX6681 only differ in the pinout so they can + * be treated identically. + * + * This driver also supports the MAX6695 and MAX6696, two other sensor + * chips made by Maxim. These are also quite similar to other Maxim + * chips, but support three temperature sensors instead of two. MAX6695 + * and MAX6696 only differ in the pinout so they can be treated identically. + * + * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as + * NCT1008 from ON Semiconductor. The chips are supported in both compatibility + * and extended mode. They are mostly compatible with LM90 except for a data + * format difference for the temperature value registers. + * + * This driver also supports the SA56004 from Philips. This device is + * pin-compatible with the LM86, the ED/EDP parts are also address-compatible. * - * This driver also supports the ADT7461 chip from Analog Devices but - * only in its "compatability mode". If an ADT7461 chip is found but - * is configured in non-compatible mode (where its temperature - * register values are decoded differently) it is ignored by this - * driver. Complete datasheet can be obtained from Analog's website - * at: - * http://www.analog.com/en/prod/0,2877,ADT7461,00.html + * This driver also supports the G781 from GMT. This device is compatible + * with the ADM1032. + * + * This driver also supports TMP451 from Texas Instruments. This device is + * supported in both compatibility and extended mode. It's mostly compatible + * with ADT7461 except for local temperature low byte register and max + * conversion rate. * * Since the LM90 was the first chipset supported by this driver, most * comments will refer to this chipset, but are actually general and @@ -88,27 +94,30 @@ #include <linux/err.h> #include <linux/mutex.h> #include <linux/sysfs.h> +#include <linux/interrupt.h> +#include <linux/regulator/consumer.h> /* * Addresses to scan * Address is fully defined internally and cannot be changed except for * MAX6659, MAX6680 and MAX6681. - * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, MAX6657 and MAX6658 - * have address 0x4c. - * ADM1032-2, ADT7461-2, LM89-1, and LM99-1 have address 0x4d. - * MAX6659 can have address 0x4c, 0x4d or 0x4e (unsupported). + * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649, + * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c. + * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D + * have address 0x4d. + * MAX6647 has address 0x4e. + * MAX6659 can have address 0x4c, 0x4d or 0x4e. * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, * 0x4c, 0x4d or 0x4e. + * SA56004 can have address 0x48 through 0x4F. */ static const unsigned short normal_i2c[] = { - 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; - -/* - * Insmod parameters - */ + 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x48, 0x49, 0x4a, 0x4b, 0x4c, + 0x4d, 0x4e, 0x4f, I2C_CLIENT_END }; -I2C_CLIENT_INSMOD_7(lm90, adm1032, lm99, lm86, max6657, adt7461, max6680); +enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680, + max6646, w83l771, max6696, sa56004, g781, tmp451 }; /* * The LM90 registers @@ -149,61 +158,206 @@ I2C_CLIENT_INSMOD_7(lm90, adm1032, lm99, lm86, max6657, adt7461, max6680); #define LM90_REG_R_TCRIT_HYST 0x21 #define LM90_REG_W_TCRIT_HYST 0x21 +/* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */ + +#define MAX6657_REG_R_LOCAL_TEMPL 0x11 +#define MAX6696_REG_R_STATUS2 0x12 +#define MAX6659_REG_R_REMOTE_EMERG 0x16 +#define MAX6659_REG_W_REMOTE_EMERG 0x16 +#define MAX6659_REG_R_LOCAL_EMERG 0x17 +#define MAX6659_REG_W_LOCAL_EMERG 0x17 + +/* SA56004 registers */ + +#define SA56004_REG_R_LOCAL_TEMPL 0x22 + +#define LM90_DEF_CONVRATE_RVAL 6 /* Def conversion rate register value */ +#define LM90_MAX_CONVRATE_MS 16000 /* Maximum conversion rate in ms */ + +/* TMP451 registers */ +#define TMP451_REG_R_LOCAL_TEMPL 0x15 + /* - * Conversions and various macros - * For local temperatures and limits, critical limits and the hysteresis - * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celsius. - * For remote temperatures and limits, it uses signed 11-bit values with - * LSB = 0.125 degree Celsius, left-justified in 16-bit registers. + * Device flags */ +#define LM90_FLAG_ADT7461_EXT (1 << 0) /* ADT7461 extended mode */ +/* Device features */ +#define LM90_HAVE_OFFSET (1 << 1) /* temperature offset register */ +#define LM90_HAVE_REM_LIMIT_EXT (1 << 3) /* extended remote limit */ +#define LM90_HAVE_EMERGENCY (1 << 4) /* 3rd upper (emergency) limit */ +#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */ +#define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */ +#define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */ + +/* LM90 status */ +#define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */ +#define LM90_STATUS_RTHRM (1 << 1) /* remote THERM limit tripped */ +#define LM90_STATUS_ROPEN (1 << 2) /* remote is an open circuit */ +#define LM90_STATUS_RLOW (1 << 3) /* remote low temp limit tripped */ +#define LM90_STATUS_RHIGH (1 << 4) /* remote high temp limit tripped */ +#define LM90_STATUS_LLOW (1 << 5) /* local low temp limit tripped */ +#define LM90_STATUS_LHIGH (1 << 6) /* local high temp limit tripped */ + +#define MAX6696_STATUS2_R2THRM (1 << 1) /* remote2 THERM limit tripped */ +#define MAX6696_STATUS2_R2OPEN (1 << 2) /* remote2 is an open circuit */ +#define MAX6696_STATUS2_R2LOW (1 << 3) /* remote2 low temp limit tripped */ +#define MAX6696_STATUS2_R2HIGH (1 << 4) /* remote2 high temp limit tripped */ +#define MAX6696_STATUS2_ROT2 (1 << 5) /* remote emergency limit tripped */ +#define MAX6696_STATUS2_R2OT2 (1 << 6) /* remote2 emergency limit tripped */ +#define MAX6696_STATUS2_LOT2 (1 << 7) /* local emergency limit tripped */ -#define TEMP1_FROM_REG(val) ((val) * 1000) -#define TEMP1_TO_REG(val) ((val) <= -128000 ? -128 : \ - (val) >= 127000 ? 127 : \ - (val) < 0 ? ((val) - 500) / 1000 : \ - ((val) + 500) / 1000) -#define TEMP2_FROM_REG(val) ((val) / 32 * 125) -#define TEMP2_TO_REG(val) ((val) <= -128000 ? 0x8000 : \ - (val) >= 127875 ? 0x7FE0 : \ - (val) < 0 ? ((val) - 62) / 125 * 32 : \ - ((val) + 62) / 125 * 32) -#define HYST_TO_REG(val) ((val) <= 0 ? 0 : (val) >= 30500 ? 31 : \ - ((val) + 500) / 1000) - -/* - * ADT7461 is almost identical to LM90 except that attempts to write - * values that are outside the range 0 < temp < 127 are treated as - * the boundary value. +/* + * Driver data (common to all clients) */ -#define TEMP1_TO_REG_ADT7461(val) ((val) <= 0 ? 0 : \ - (val) >= 127000 ? 127 : \ - ((val) + 500) / 1000) -#define TEMP2_TO_REG_ADT7461(val) ((val) <= 0 ? 0 : \ - (val) >= 127750 ? 0x7FC0 : \ - ((val) + 125) / 250 * 64) +static const struct i2c_device_id lm90_id[] = { + { "adm1032", adm1032 }, + { "adt7461", adt7461 }, + { "adt7461a", adt7461 }, + { "g781", g781 }, + { "lm90", lm90 }, + { "lm86", lm86 }, + { "lm89", lm86 }, + { "lm99", lm99 }, + { "max6646", max6646 }, + { "max6647", max6646 }, + { "max6649", max6646 }, + { "max6657", max6657 }, + { "max6658", max6657 }, + { "max6659", max6659 }, + { "max6680", max6680 }, + { "max6681", max6680 }, + { "max6695", max6696 }, + { "max6696", max6696 }, + { "nct1008", adt7461 }, + { "w83l771", w83l771 }, + { "sa56004", sa56004 }, + { "tmp451", tmp451 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lm90_id); /* - * Functions declaration + * chip type specific parameters */ +struct lm90_params { + u32 flags; /* Capabilities */ + u16 alert_alarms; /* Which alarm bits trigger ALERT# */ + /* Upper 8 bits for max6695/96 */ + u8 max_convrate; /* Maximum conversion rate register value */ + u8 reg_local_ext; /* Extended local temp register (optional) */ +}; -static int lm90_attach_adapter(struct i2c_adapter *adapter); -static int lm90_detect(struct i2c_adapter *adapter, int address, - int kind); -static void lm90_init_client(struct i2c_client *client); -static int lm90_detach_client(struct i2c_client *client); -static struct lm90_data *lm90_update_device(struct device *dev); +static const struct lm90_params lm90_params[] = { + [adm1032] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT + | LM90_HAVE_BROKEN_ALERT, + .alert_alarms = 0x7c, + .max_convrate = 10, + }, + [adt7461] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT + | LM90_HAVE_BROKEN_ALERT, + .alert_alarms = 0x7c, + .max_convrate = 10, + }, + [g781] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT + | LM90_HAVE_BROKEN_ALERT, + .alert_alarms = 0x7c, + .max_convrate = 8, + }, + [lm86] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .alert_alarms = 0x7b, + .max_convrate = 9, + }, + [lm90] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .alert_alarms = 0x7b, + .max_convrate = 9, + }, + [lm99] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .alert_alarms = 0x7b, + .max_convrate = 9, + }, + [max6646] = { + .alert_alarms = 0x7c, + .max_convrate = 6, + .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, + }, + [max6657] = { + .alert_alarms = 0x7c, + .max_convrate = 8, + .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, + }, + [max6659] = { + .flags = LM90_HAVE_EMERGENCY, + .alert_alarms = 0x7c, + .max_convrate = 8, + .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, + }, + [max6680] = { + .flags = LM90_HAVE_OFFSET, + .alert_alarms = 0x7c, + .max_convrate = 7, + }, + [max6696] = { + .flags = LM90_HAVE_EMERGENCY + | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3, + .alert_alarms = 0x1c7c, + .max_convrate = 6, + .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, + }, + [w83l771] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .alert_alarms = 0x7c, + .max_convrate = 8, + }, + [sa56004] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, + .alert_alarms = 0x7b, + .max_convrate = 9, + .reg_local_ext = SA56004_REG_R_LOCAL_TEMPL, + }, + [tmp451] = { + .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT + | LM90_HAVE_BROKEN_ALERT, + .alert_alarms = 0x7c, + .max_convrate = 9, + .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL, + } +}; /* - * Driver data (common to all clients) + * TEMP8 register index */ +enum lm90_temp8_reg_index { + LOCAL_LOW = 0, + LOCAL_HIGH, + LOCAL_CRIT, + REMOTE_CRIT, + LOCAL_EMERG, /* max6659 and max6695/96 */ + REMOTE_EMERG, /* max6659 and max6695/96 */ + REMOTE2_CRIT, /* max6695/96 only */ + REMOTE2_EMERG, /* max6695/96 only */ + TEMP8_REG_NUM +}; -static struct i2c_driver lm90_driver = { - .driver = { - .name = "lm90", - }, - .attach_adapter = lm90_attach_adapter, - .detach_client = lm90_detach_client, +/* + * TEMP11 register index + */ +enum lm90_temp11_reg_index { + REMOTE_TEMP = 0, + REMOTE_LOW, + REMOTE_HIGH, + REMOTE_OFFSET, /* except max6646, max6657/58/59, and max6695/96 */ + LOCAL_TEMP, + REMOTE2_TEMP, /* max6695/96 only */ + REMOTE2_LOW, /* max6695/96 only */ + REMOTE2_HIGH, /* max6695/96 only */ + TEMP11_REG_NUM }; /* @@ -211,28 +365,397 @@ static struct i2c_driver lm90_driver = { */ struct lm90_data { - struct i2c_client client; + struct i2c_client *client; struct device *hwmon_dev; + const struct attribute_group *groups[6]; struct mutex update_lock; + struct regulator *regulator; char valid; /* zero until following fields are valid */ unsigned long last_updated; /* in jiffies */ int kind; + u32 flags; + + int update_interval; /* in milliseconds */ + + u8 config_orig; /* Original configuration register value */ + u8 convrate_orig; /* Original conversion rate register value */ + u16 alert_alarms; /* Which alarm bits trigger ALERT# */ + /* Upper 8 bits for max6695/96 */ + u8 max_convrate; /* Maximum conversion rate */ + u8 reg_local_ext; /* local extension register offset */ /* registers values */ - s8 temp8[5]; /* 0: local input - 1: local low limit - 2: local high limit - 3: local critical limit - 4: remote critical limit */ - s16 temp11[4]; /* 0: remote input - 1: remote low limit - 2: remote high limit - 3: remote offset (except max6657) */ + s8 temp8[TEMP8_REG_NUM]; + s16 temp11[TEMP11_REG_NUM]; u8 temp_hyst; - u8 alarms; /* bitvector */ + u16 alarms; /* bitvector (upper 8 bits for max6695/96) */ }; /* + * Support functions + */ + +/* + * The ADM1032 supports PEC but not on write byte transactions, so we need + * to explicitly ask for a transaction without PEC. + */ +static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value) +{ + return i2c_smbus_xfer(client->adapter, client->addr, + client->flags & ~I2C_CLIENT_PEC, + I2C_SMBUS_WRITE, value, I2C_SMBUS_BYTE, NULL); +} + +/* + * It is assumed that client->update_lock is held (unless we are in + * detection or initialization steps). This matters when PEC is enabled, + * because we don't want the address pointer to change between the write + * byte and the read byte transactions. + */ +static int lm90_read_reg(struct i2c_client *client, u8 reg, u8 *value) +{ + int err; + + if (client->flags & I2C_CLIENT_PEC) { + err = adm1032_write_byte(client, reg); + if (err >= 0) + err = i2c_smbus_read_byte(client); + } else + err = i2c_smbus_read_byte_data(client, reg); + + if (err < 0) { + dev_warn(&client->dev, "Register %#02x read failed (%d)\n", + reg, err); + return err; + } + *value = err; + + return 0; +} + +static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl, u16 *value) +{ + int err; + u8 oldh, newh, l; + + /* + * There is a trick here. We have to read two registers to have the + * sensor temperature, but we have to beware a conversion could occur + * between the readings. The datasheet says we should either use + * the one-shot conversion register, which we don't want to do + * (disables hardware monitoring) or monitor the busy bit, which is + * impossible (we can't read the values and monitor that bit at the + * exact same time). So the solution used here is to read the high + * byte once, then the low byte, then the high byte again. If the new + * high byte matches the old one, then we have a valid reading. Else + * we have to read the low byte again, and now we believe we have a + * correct reading. + */ + if ((err = lm90_read_reg(client, regh, &oldh)) + || (err = lm90_read_reg(client, regl, &l)) + || (err = lm90_read_reg(client, regh, &newh))) + return err; + if (oldh != newh) { + err = lm90_read_reg(client, regl, &l); + if (err) + return err; + } + *value = (newh << 8) | l; + + return 0; +} + +/* + * client->update_lock must be held when calling this function (unless we are + * in detection or initialization steps), and while a remote channel other + * than channel 0 is selected. Also, calling code must make sure to re-select + * external channel 0 before releasing the lock. This is necessary because + * various registers have different meanings as a result of selecting a + * non-default remote channel. + */ +static inline void lm90_select_remote_channel(struct i2c_client *client, + struct lm90_data *data, + int channel) +{ + u8 config; + + if (data->kind == max6696) { + lm90_read_reg(client, LM90_REG_R_CONFIG1, &config); + config &= ~0x08; + if (channel) + config |= 0x08; + i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, + config); + } +} + +/* + * Set conversion rate. + * client->update_lock must be held when calling this function (unless we are + * in detection or initialization steps). + */ +static void lm90_set_convrate(struct i2c_client *client, struct lm90_data *data, + unsigned int interval) +{ + int i; + unsigned int update_interval; + + /* Shift calculations to avoid rounding errors */ + interval <<= 6; + + /* find the nearest update rate */ + for (i = 0, update_interval = LM90_MAX_CONVRATE_MS << 6; + i < data->max_convrate; i++, update_interval >>= 1) + if (interval >= update_interval * 3 / 4) + break; + + i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, i); + data->update_interval = DIV_ROUND_CLOSEST(update_interval, 64); +} + +static struct lm90_data *lm90_update_device(struct device *dev) +{ + struct lm90_data *data = dev_get_drvdata(dev); + struct i2c_client *client = data->client; + unsigned long next_update; + + mutex_lock(&data->update_lock); + + next_update = data->last_updated + + msecs_to_jiffies(data->update_interval); + if (time_after(jiffies, next_update) || !data->valid) { + u8 h, l; + u8 alarms; + + dev_dbg(&client->dev, "Updating lm90 data.\n"); + lm90_read_reg(client, LM90_REG_R_LOCAL_LOW, + &data->temp8[LOCAL_LOW]); + lm90_read_reg(client, LM90_REG_R_LOCAL_HIGH, + &data->temp8[LOCAL_HIGH]); + lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT, + &data->temp8[LOCAL_CRIT]); + lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT, + &data->temp8[REMOTE_CRIT]); + lm90_read_reg(client, LM90_REG_R_TCRIT_HYST, &data->temp_hyst); + + if (data->reg_local_ext) { + lm90_read16(client, LM90_REG_R_LOCAL_TEMP, + data->reg_local_ext, + &data->temp11[LOCAL_TEMP]); + } else { + if (lm90_read_reg(client, LM90_REG_R_LOCAL_TEMP, + &h) == 0) + data->temp11[LOCAL_TEMP] = h << 8; + } + lm90_read16(client, LM90_REG_R_REMOTE_TEMPH, + LM90_REG_R_REMOTE_TEMPL, + &data->temp11[REMOTE_TEMP]); + + if (lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &h) == 0) { + data->temp11[REMOTE_LOW] = h << 8; + if ((data->flags & LM90_HAVE_REM_LIMIT_EXT) + && lm90_read_reg(client, LM90_REG_R_REMOTE_LOWL, + &l) == 0) + data->temp11[REMOTE_LOW] |= l; + } + if (lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &h) == 0) { + data->temp11[REMOTE_HIGH] = h << 8; + if ((data->flags & LM90_HAVE_REM_LIMIT_EXT) + && lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHL, + &l) == 0) + data->temp11[REMOTE_HIGH] |= l; + } + + if (data->flags & LM90_HAVE_OFFSET) { + if (lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSH, + &h) == 0 + && lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSL, + &l) == 0) + data->temp11[REMOTE_OFFSET] = (h << 8) | l; + } + if (data->flags & LM90_HAVE_EMERGENCY) { + lm90_read_reg(client, MAX6659_REG_R_LOCAL_EMERG, + &data->temp8[LOCAL_EMERG]); + lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG, + &data->temp8[REMOTE_EMERG]); + } + lm90_read_reg(client, LM90_REG_R_STATUS, &alarms); + data->alarms = alarms; /* save as 16 bit value */ + + if (data->kind == max6696) { + lm90_select_remote_channel(client, data, 1); + lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT, + &data->temp8[REMOTE2_CRIT]); + lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG, + &data->temp8[REMOTE2_EMERG]); + lm90_read16(client, LM90_REG_R_REMOTE_TEMPH, + LM90_REG_R_REMOTE_TEMPL, + &data->temp11[REMOTE2_TEMP]); + if (!lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &h)) + data->temp11[REMOTE2_LOW] = h << 8; + if (!lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &h)) + data->temp11[REMOTE2_HIGH] = h << 8; + lm90_select_remote_channel(client, data, 0); + + if (!lm90_read_reg(client, MAX6696_REG_R_STATUS2, + &alarms)) + data->alarms |= alarms << 8; + } + + /* + * Re-enable ALERT# output if it was originally enabled and + * relevant alarms are all clear + */ + if ((data->config_orig & 0x80) == 0 + && (data->alarms & data->alert_alarms) == 0) { + u8 config; + + lm90_read_reg(client, LM90_REG_R_CONFIG1, &config); + if (config & 0x80) { + dev_dbg(&client->dev, "Re-enabling ALERT#\n"); + i2c_smbus_write_byte_data(client, + LM90_REG_W_CONFIG1, + config & ~0x80); + } + } + + data->last_updated = jiffies; + data->valid = 1; + } + + mutex_unlock(&data->update_lock); + + return data; +} + +/* + * Conversions + * For local temperatures and limits, critical limits and the hysteresis + * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celsius. + * For remote temperatures and limits, it uses signed 11-bit values with + * LSB = 0.125 degree Celsius, left-justified in 16-bit registers. Some + * Maxim chips use unsigned values. + */ + +static inline int temp_from_s8(s8 val) +{ + return val * 1000; +} + +static inline int temp_from_u8(u8 val) +{ + return val * 1000; +} + +static inline int temp_from_s16(s16 val) +{ + return val / 32 * 125; +} + +static inline int temp_from_u16(u16 val) +{ + return val / 32 * 125; +} + +static s8 temp_to_s8(long val) +{ + if (val <= -128000) + return -128; + if (val >= 127000) + return 127; + if (val < 0) + return (val - 500) / 1000; + return (val + 500) / 1000; +} + +static u8 temp_to_u8(long val) +{ + if (val <= 0) + return 0; + if (val >= 255000) + return 255; + return (val + 500) / 1000; +} + +static s16 temp_to_s16(long val) +{ + if (val <= -128000) + return 0x8000; + if (val >= 127875) + return 0x7FE0; + if (val < 0) + return (val - 62) / 125 * 32; + return (val + 62) / 125 * 32; +} + +static u8 hyst_to_reg(long val) +{ + if (val <= 0) + return 0; + if (val >= 30500) + return 31; + return (val + 500) / 1000; +} + +/* + * ADT7461 in compatibility mode is almost identical to LM90 except that + * attempts to write values that are outside the range 0 < temp < 127 are + * treated as the boundary value. + * + * ADT7461 in "extended mode" operation uses unsigned integers offset by + * 64 (e.g., 0 -> -64 degC). The range is restricted to -64..191 degC. + */ +static inline int temp_from_u8_adt7461(struct lm90_data *data, u8 val) +{ + if (data->flags & LM90_FLAG_ADT7461_EXT) + return (val - 64) * 1000; + else + return temp_from_s8(val); +} + +static inline int temp_from_u16_adt7461(struct lm90_data *data, u16 val) +{ + if (data->flags & LM90_FLAG_ADT7461_EXT) + return (val - 0x4000) / 64 * 250; + else + return temp_from_s16(val); +} + +static u8 temp_to_u8_adt7461(struct lm90_data *data, long val) +{ + if (data->flags & LM90_FLAG_ADT7461_EXT) { + if (val <= -64000) + return 0; + if (val >= 191000) + return 0xFF; + return (val + 500 + 64000) / 1000; + } else { + if (val <= 0) + return 0; + if (val >= 127000) + return 127; + return (val + 500) / 1000; + } +} + +static u16 temp_to_u16_adt7461(struct lm90_data *data, long val) +{ + if (data->flags & LM90_FLAG_ADT7461_EXT) { + if (val <= -64000) + return 0; + if (val >= 191750) + return 0xFFC0; + return (val + 64000 + 125) / 250 * 64; + } else { + if (val <= 0) + return 0; + if (val >= 127750) + return 0x7FC0; + return (val + 125) / 250 * 64; + } +} + +/* * Sysfs stuff */ @@ -241,31 +764,63 @@ static ssize_t show_temp8(struct device *dev, struct device_attribute *devattr, { struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); struct lm90_data *data = lm90_update_device(dev); - return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp8[attr->index])); + int temp; + + if (data->kind == adt7461 || data->kind == tmp451) + temp = temp_from_u8_adt7461(data, data->temp8[attr->index]); + else if (data->kind == max6646) + temp = temp_from_u8(data->temp8[attr->index]); + else + temp = temp_from_s8(data->temp8[attr->index]); + + /* +16 degrees offset for temp2 for the LM99 */ + if (data->kind == lm99 && attr->index == 3) + temp += 16000; + + return sprintf(buf, "%d\n", temp); } static ssize_t set_temp8(struct device *dev, struct device_attribute *devattr, const char *buf, size_t count) { - static const u8 reg[4] = { + static const u8 reg[TEMP8_REG_NUM] = { LM90_REG_W_LOCAL_LOW, LM90_REG_W_LOCAL_HIGH, LM90_REG_W_LOCAL_CRIT, LM90_REG_W_REMOTE_CRIT, + MAX6659_REG_W_LOCAL_EMERG, + MAX6659_REG_W_REMOTE_EMERG, + LM90_REG_W_REMOTE_CRIT, + MAX6659_REG_W_REMOTE_EMERG, }; struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); - struct i2c_client *client = to_i2c_client(dev); - struct lm90_data *data = i2c_get_clientdata(client); - long val = simple_strtol(buf, NULL, 10); + struct lm90_data *data = dev_get_drvdata(dev); + struct i2c_client *client = data->client; int nr = attr->index; + long val; + int err; + + err = kstrtol(buf, 10, &val); + if (err < 0) + return err; + + /* +16 degrees offset for temp2 for the LM99 */ + if (data->kind == lm99 && attr->index == 3) + val -= 16000; mutex_lock(&data->update_lock); - if (data->kind == adt7461) - data->temp8[nr] = TEMP1_TO_REG_ADT7461(val); + if (data->kind == adt7461 || data->kind == tmp451) + data->temp8[nr] = temp_to_u8_adt7461(data, val); + else if (data->kind == max6646) + data->temp8[nr] = temp_to_u8(val); else - data->temp8[nr] = TEMP1_TO_REG(val); - i2c_smbus_write_byte_data(client, reg[nr - 1], data->temp8[nr]); + data->temp8[nr] = temp_to_s8(val); + + lm90_select_remote_channel(client, data, nr >= 6); + i2c_smbus_write_byte_data(client, reg[nr], data->temp8[nr]); + lm90_select_remote_channel(client, data, 0); + mutex_unlock(&data->update_lock); return count; } @@ -273,63 +828,123 @@ static ssize_t set_temp8(struct device *dev, struct device_attribute *devattr, static ssize_t show_temp11(struct device *dev, struct device_attribute *devattr, char *buf) { - struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); struct lm90_data *data = lm90_update_device(dev); - return sprintf(buf, "%d\n", TEMP2_FROM_REG(data->temp11[attr->index])); + int temp; + + if (data->kind == adt7461 || data->kind == tmp451) + temp = temp_from_u16_adt7461(data, data->temp11[attr->index]); + else if (data->kind == max6646) + temp = temp_from_u16(data->temp11[attr->index]); + else + temp = temp_from_s16(data->temp11[attr->index]); + + /* +16 degrees offset for temp2 for the LM99 */ + if (data->kind == lm99 && attr->index <= 2) + temp += 16000; + + return sprintf(buf, "%d\n", temp); } static ssize_t set_temp11(struct device *dev, struct device_attribute *devattr, const char *buf, size_t count) { - static const u8 reg[6] = { - LM90_REG_W_REMOTE_LOWH, - LM90_REG_W_REMOTE_LOWL, - LM90_REG_W_REMOTE_HIGHH, - LM90_REG_W_REMOTE_HIGHL, - LM90_REG_W_REMOTE_OFFSH, - LM90_REG_W_REMOTE_OFFSL, + struct { + u8 high; + u8 low; + int channel; + } reg[5] = { + { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL, 0 }, + { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL, 0 }, + { LM90_REG_W_REMOTE_OFFSH, LM90_REG_W_REMOTE_OFFSL, 0 }, + { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL, 1 }, + { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL, 1 } }; - struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); - struct i2c_client *client = to_i2c_client(dev); - struct lm90_data *data = i2c_get_clientdata(client); - long val = simple_strtol(buf, NULL, 10); - int nr = attr->index; + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct lm90_data *data = dev_get_drvdata(dev); + struct i2c_client *client = data->client; + int nr = attr->nr; + int index = attr->index; + long val; + int err; + + err = kstrtol(buf, 10, &val); + if (err < 0) + return err; + + /* +16 degrees offset for temp2 for the LM99 */ + if (data->kind == lm99 && index <= 2) + val -= 16000; mutex_lock(&data->update_lock); - if (data->kind == adt7461) - data->temp11[nr] = TEMP2_TO_REG_ADT7461(val); + if (data->kind == adt7461 || data->kind == tmp451) + data->temp11[index] = temp_to_u16_adt7461(data, val); + else if (data->kind == max6646) + data->temp11[index] = temp_to_u8(val) << 8; + else if (data->flags & LM90_HAVE_REM_LIMIT_EXT) + data->temp11[index] = temp_to_s16(val); else - data->temp11[nr] = TEMP2_TO_REG(val); - i2c_smbus_write_byte_data(client, reg[(nr - 1) * 2], - data->temp11[nr] >> 8); - i2c_smbus_write_byte_data(client, reg[(nr - 1) * 2 + 1], - data->temp11[nr] & 0xff); + data->temp11[index] = temp_to_s8(val) << 8; + + lm90_select_remote_channel(client, data, reg[nr].channel); + i2c_smbus_write_byte_data(client, reg[nr].high, + data->temp11[index] >> 8); + if (data->flags & LM90_HAVE_REM_LIMIT_EXT) + i2c_smbus_write_byte_data(client, reg[nr].low, + data->temp11[index] & 0xff); + lm90_select_remote_channel(client, data, 0); + mutex_unlock(&data->update_lock); return count; } -static ssize_t show_temphyst(struct device *dev, struct device_attribute *devattr, +static ssize_t show_temphyst(struct device *dev, + struct device_attribute *devattr, char *buf) { struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); struct lm90_data *data = lm90_update_device(dev); - return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp8[attr->index]) - - TEMP1_FROM_REG(data->temp_hyst)); + int temp; + + if (data->kind == adt7461 || data->kind == tmp451) + temp = temp_from_u8_adt7461(data, data->temp8[attr->index]); + else if (data->kind == max6646) + temp = temp_from_u8(data->temp8[attr->index]); + else + temp = temp_from_s8(data->temp8[attr->index]); + + /* +16 degrees offset for temp2 for the LM99 */ + if (data->kind == lm99 && attr->index == 3) + temp += 16000; + + return sprintf(buf, "%d\n", temp - temp_from_s8(data->temp_hyst)); } static ssize_t set_temphyst(struct device *dev, struct device_attribute *dummy, const char *buf, size_t count) { - struct i2c_client *client = to_i2c_client(dev); - struct lm90_data *data = i2c_get_clientdata(client); - long val = simple_strtol(buf, NULL, 10); - long hyst; + struct lm90_data *data = dev_get_drvdata(dev); + struct i2c_client *client = data->client; + long val; + int err; + int temp; + + err = kstrtol(buf, 10, &val); + if (err < 0) + return err; mutex_lock(&data->update_lock); - hyst = TEMP1_FROM_REG(data->temp8[3]) - val; + if (data->kind == adt7461 || data->kind == tmp451) + temp = temp_from_u8_adt7461(data, data->temp8[LOCAL_CRIT]); + else if (data->kind == max6646) + temp = temp_from_u8(data->temp8[LOCAL_CRIT]); + else + temp = temp_from_s8(data->temp8[LOCAL_CRIT]); + + data->temp_hyst = hyst_to_reg(temp - val); i2c_smbus_write_byte_data(client, LM90_REG_W_TCRIT_HYST, - HYST_TO_REG(hyst)); + data->temp_hyst); mutex_unlock(&data->update_lock); return count; } @@ -351,25 +966,56 @@ static ssize_t show_alarm(struct device *dev, struct device_attribute return sprintf(buf, "%d\n", (data->alarms >> bitnr) & 1); } -static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp8, NULL, 0); -static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp11, NULL, 0); +static ssize_t show_update_interval(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct lm90_data *data = dev_get_drvdata(dev); + + return sprintf(buf, "%u\n", data->update_interval); +} + +static ssize_t set_update_interval(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct lm90_data *data = dev_get_drvdata(dev); + struct i2c_client *client = data->client; + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + + mutex_lock(&data->update_lock); + lm90_set_convrate(client, data, clamp_val(val, 0, 100000)); + mutex_unlock(&data->update_lock); + + return count; +} + +static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp11, NULL, + 0, LOCAL_TEMP); +static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp11, NULL, + 0, REMOTE_TEMP); static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp8, - set_temp8, 1); -static SENSOR_DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO, show_temp11, - set_temp11, 1); + set_temp8, LOCAL_LOW); +static SENSOR_DEVICE_ATTR_2(temp2_min, S_IWUSR | S_IRUGO, show_temp11, + set_temp11, 0, REMOTE_LOW); static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp8, - set_temp8, 2); -static SENSOR_DEVICE_ATTR(temp2_max, S_IWUSR | S_IRUGO, show_temp11, - set_temp11, 2); + set_temp8, LOCAL_HIGH); +static SENSOR_DEVICE_ATTR_2(temp2_max, S_IWUSR | S_IRUGO, show_temp11, + set_temp11, 1, REMOTE_HIGH); static SENSOR_DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp8, - set_temp8, 3); + set_temp8, LOCAL_CRIT); static SENSOR_DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_temp8, - set_temp8, 4); + set_temp8, REMOTE_CRIT); static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_temphyst, - set_temphyst, 3); -static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IRUGO, show_temphyst, NULL, 4); -static SENSOR_DEVICE_ATTR(temp2_offset, S_IWUSR | S_IRUGO, show_temp11, - set_temp11, 3); + set_temphyst, LOCAL_CRIT); +static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IRUGO, show_temphyst, NULL, + REMOTE_CRIT); +static SENSOR_DEVICE_ATTR_2(temp2_offset, S_IWUSR | S_IRUGO, show_temp11, + set_temp11, 2, REMOTE_OFFSET); /* Individual alarm files */ static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 0); @@ -382,6 +1028,9 @@ static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6); /* Raw alarm file for compatibility */ static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); +static DEVICE_ATTR(update_interval, S_IRUGO | S_IWUSR, show_update_interval, + set_update_interval); + static struct attribute *lm90_attributes[] = { &sensor_dev_attr_temp1_input.dev_attr.attr, &sensor_dev_attr_temp2_input.dev_attr.attr, @@ -402,6 +1051,7 @@ static struct attribute *lm90_attributes[] = { &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, &dev_attr_alarms.attr, + &dev_attr_update_interval.attr, NULL }; @@ -409,6 +1059,97 @@ static const struct attribute_group lm90_group = { .attrs = lm90_attributes, }; +static struct attribute *lm90_temp2_offset_attributes[] = { + &sensor_dev_attr_temp2_offset.dev_attr.attr, + NULL +}; + +static const struct attribute_group lm90_temp2_offset_group = { + .attrs = lm90_temp2_offset_attributes, +}; + +/* + * Additional attributes for devices with emergency sensors + */ +static SENSOR_DEVICE_ATTR(temp1_emergency, S_IWUSR | S_IRUGO, show_temp8, + set_temp8, LOCAL_EMERG); +static SENSOR_DEVICE_ATTR(temp2_emergency, S_IWUSR | S_IRUGO, show_temp8, + set_temp8, REMOTE_EMERG); +static SENSOR_DEVICE_ATTR(temp1_emergency_hyst, S_IRUGO, show_temphyst, + NULL, LOCAL_EMERG); +static SENSOR_DEVICE_ATTR(temp2_emergency_hyst, S_IRUGO, show_temphyst, + NULL, REMOTE_EMERG); + +static struct attribute *lm90_emergency_attributes[] = { + &sensor_dev_attr_temp1_emergency.dev_attr.attr, + &sensor_dev_attr_temp2_emergency.dev_attr.attr, + &sensor_dev_attr_temp1_emergency_hyst.dev_attr.attr, + &sensor_dev_attr_temp2_emergency_hyst.dev_attr.attr, + NULL +}; + +static const struct attribute_group lm90_emergency_group = { + .attrs = lm90_emergency_attributes, +}; + +static SENSOR_DEVICE_ATTR(temp1_emergency_alarm, S_IRUGO, show_alarm, NULL, 15); +static SENSOR_DEVICE_ATTR(temp2_emergency_alarm, S_IRUGO, show_alarm, NULL, 13); + +static struct attribute *lm90_emergency_alarm_attributes[] = { + &sensor_dev_attr_temp1_emergency_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_emergency_alarm.dev_attr.attr, + NULL +}; + +static const struct attribute_group lm90_emergency_alarm_group = { + .attrs = lm90_emergency_alarm_attributes, +}; + +/* + * Additional attributes for devices with 3 temperature sensors + */ +static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp11, NULL, + 0, REMOTE2_TEMP); +static SENSOR_DEVICE_ATTR_2(temp3_min, S_IWUSR | S_IRUGO, show_temp11, + set_temp11, 3, REMOTE2_LOW); +static SENSOR_DEVICE_ATTR_2(temp3_max, S_IWUSR | S_IRUGO, show_temp11, + set_temp11, 4, REMOTE2_HIGH); +static SENSOR_DEVICE_ATTR(temp3_crit, S_IWUSR | S_IRUGO, show_temp8, + set_temp8, REMOTE2_CRIT); +static SENSOR_DEVICE_ATTR(temp3_crit_hyst, S_IRUGO, show_temphyst, NULL, + REMOTE2_CRIT); +static SENSOR_DEVICE_ATTR(temp3_emergency, S_IWUSR | S_IRUGO, show_temp8, + set_temp8, REMOTE2_EMERG); +static SENSOR_DEVICE_ATTR(temp3_emergency_hyst, S_IRUGO, show_temphyst, + NULL, REMOTE2_EMERG); + +static SENSOR_DEVICE_ATTR(temp3_crit_alarm, S_IRUGO, show_alarm, NULL, 9); +static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 10); +static SENSOR_DEVICE_ATTR(temp3_min_alarm, S_IRUGO, show_alarm, NULL, 11); +static SENSOR_DEVICE_ATTR(temp3_max_alarm, S_IRUGO, show_alarm, NULL, 12); +static SENSOR_DEVICE_ATTR(temp3_emergency_alarm, S_IRUGO, show_alarm, NULL, 14); + +static struct attribute *lm90_temp3_attributes[] = { + &sensor_dev_attr_temp3_input.dev_attr.attr, + &sensor_dev_attr_temp3_min.dev_attr.attr, + &sensor_dev_attr_temp3_max.dev_attr.attr, + &sensor_dev_attr_temp3_crit.dev_attr.attr, + &sensor_dev_attr_temp3_crit_hyst.dev_attr.attr, + &sensor_dev_attr_temp3_emergency.dev_attr.attr, + &sensor_dev_attr_temp3_emergency_hyst.dev_attr.attr, + + &sensor_dev_attr_temp3_fault.dev_attr.attr, + &sensor_dev_attr_temp3_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp3_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp3_crit_alarm.dev_attr.attr, + &sensor_dev_attr_temp3_emergency_alarm.dev_attr.attr, + NULL +}; + +static const struct attribute_group lm90_temp3_group = { + .attrs = lm90_temp3_attributes, +}; + /* pec used for ADM1032 only */ static ssize_t show_pec(struct device *dev, struct device_attribute *dummy, char *buf) @@ -421,7 +1162,12 @@ static ssize_t set_pec(struct device *dev, struct device_attribute *dummy, const char *buf, size_t count) { struct i2c_client *client = to_i2c_client(dev); - long val = simple_strtol(buf, NULL, 10); + long val; + int err; + + err = kstrtol(buf, 10, &val); + if (err < 0) + return err; switch (val) { case 0: @@ -443,368 +1189,481 @@ static DEVICE_ATTR(pec, S_IWUSR | S_IRUGO, show_pec, set_pec); * Real code */ -/* The ADM1032 supports PEC but not on write byte transactions, so we need - to explicitly ask for a transaction without PEC. */ -static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value) -{ - return i2c_smbus_xfer(client->adapter, client->addr, - client->flags & ~I2C_CLIENT_PEC, - I2C_SMBUS_WRITE, value, I2C_SMBUS_BYTE, NULL); -} - -/* It is assumed that client->update_lock is held (unless we are in - detection or initialization steps). This matters when PEC is enabled, - because we don't want the address pointer to change between the write - byte and the read byte transactions. */ -static int lm90_read_reg(struct i2c_client* client, u8 reg, u8 *value) +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int lm90_detect(struct i2c_client *client, + struct i2c_board_info *info) { - int err; - - if (client->flags & I2C_CLIENT_PEC) { - err = adm1032_write_byte(client, reg); - if (err >= 0) - err = i2c_smbus_read_byte(client); - } else - err = i2c_smbus_read_byte_data(client, reg); - - if (err < 0) { - dev_warn(&client->dev, "Register %#02x read failed (%d)\n", - reg, err); - return err; - } - *value = err; - - return 0; -} - -static int lm90_attach_adapter(struct i2c_adapter *adapter) -{ - if (!(adapter->class & I2C_CLASS_HWMON)) - return 0; - return i2c_probe(adapter, &addr_data, lm90_detect); -} - -/* - * The following function does more than just detection. If detection - * succeeds, it also registers the new chip. - */ -static int lm90_detect(struct i2c_adapter *adapter, int address, int kind) -{ - struct i2c_client *new_client; - struct lm90_data *data; - int err = 0; - const char *name = ""; + struct i2c_adapter *adapter = client->adapter; + int address = client->addr; + const char *name = NULL; + int man_id, chip_id, config1, config2, convrate; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - goto exit; - - if (!(data = kzalloc(sizeof(struct lm90_data), GFP_KERNEL))) { - err = -ENOMEM; - goto exit; - } - - /* The common I2C client data is placed right before the - LM90-specific data. */ - new_client = &data->client; - i2c_set_clientdata(new_client, data); - new_client->addr = address; - new_client->adapter = adapter; - new_client->driver = &lm90_driver; - new_client->flags = 0; - - /* - * Now we do the remaining detection. A negative kind means that - * the driver was loaded with no force parameter (default), so we - * must both detect and identify the chip. A zero kind means that - * the driver was loaded with the force parameter, the detection - * step shall be skipped. A positive kind means that the driver - * was loaded with the force parameter and a given kind of chip is - * requested, so both the detection and the identification steps - * are skipped. - */ - - /* Default to an LM90 if forced */ - if (kind == 0) - kind = lm90; - - if (kind < 0) { /* detection and identification */ - int man_id, chip_id, reg_config1, reg_convrate; - - if ((man_id = i2c_smbus_read_byte_data(new_client, - LM90_REG_R_MAN_ID)) < 0 - || (chip_id = i2c_smbus_read_byte_data(new_client, - LM90_REG_R_CHIP_ID)) < 0 - || (reg_config1 = i2c_smbus_read_byte_data(new_client, - LM90_REG_R_CONFIG1)) < 0 - || (reg_convrate = i2c_smbus_read_byte_data(new_client, - LM90_REG_R_CONVRATE)) < 0) - goto exit_free; - - if ((address == 0x4C || address == 0x4D) - && man_id == 0x01) { /* National Semiconductor */ - int reg_config2; - - if ((reg_config2 = i2c_smbus_read_byte_data(new_client, - LM90_REG_R_CONFIG2)) < 0) - goto exit_free; - - if ((reg_config1 & 0x2A) == 0x00 - && (reg_config2 & 0xF8) == 0x00 - && reg_convrate <= 0x09) { - if (address == 0x4C - && (chip_id & 0xF0) == 0x20) { /* LM90 */ - kind = lm90; - } else - if ((chip_id & 0xF0) == 0x30) { /* LM89/LM99 */ - kind = lm99; - } else - if (address == 0x4C - && (chip_id & 0xF0) == 0x10) { /* LM86 */ - kind = lm86; - } - } - } else - if ((address == 0x4C || address == 0x4D) - && man_id == 0x41) { /* Analog Devices */ - if ((chip_id & 0xF0) == 0x40 /* ADM1032 */ - && (reg_config1 & 0x3F) == 0x00 - && reg_convrate <= 0x0A) { - kind = adm1032; + return -ENODEV; + + /* detection and identification */ + man_id = i2c_smbus_read_byte_data(client, LM90_REG_R_MAN_ID); + chip_id = i2c_smbus_read_byte_data(client, LM90_REG_R_CHIP_ID); + config1 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG1); + convrate = i2c_smbus_read_byte_data(client, LM90_REG_R_CONVRATE); + if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0) + return -ENODEV; + + if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) { + config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2); + if (config2 < 0) + return -ENODEV; + } else + config2 = 0; /* Make compiler happy */ + + if ((address == 0x4C || address == 0x4D) + && man_id == 0x01) { /* National Semiconductor */ + if ((config1 & 0x2A) == 0x00 + && (config2 & 0xF8) == 0x00 + && convrate <= 0x09) { + if (address == 0x4C + && (chip_id & 0xF0) == 0x20) { /* LM90 */ + name = "lm90"; } else - if (chip_id == 0x51 /* ADT7461 */ - && (reg_config1 & 0x1F) == 0x00 /* check compat mode */ - && reg_convrate <= 0x0A) { - kind = adt7461; + if ((chip_id & 0xF0) == 0x30) { /* LM89/LM99 */ + name = "lm99"; + dev_info(&adapter->dev, + "Assuming LM99 chip at 0x%02x\n", + address); + dev_info(&adapter->dev, + "If it is an LM89, instantiate it " + "with the new_device sysfs " + "interface\n"); + } else + if (address == 0x4C + && (chip_id & 0xF0) == 0x10) { /* LM86 */ + name = "lm86"; } - } else - if (man_id == 0x4D) { /* Maxim */ + } + } else + if ((address == 0x4C || address == 0x4D) + && man_id == 0x41) { /* Analog Devices */ + if ((chip_id & 0xF0) == 0x40 /* ADM1032 */ + && (config1 & 0x3F) == 0x00 + && convrate <= 0x0A) { + name = "adm1032"; /* - * The MAX6657, MAX6658 and MAX6659 do NOT have a - * chip_id register. Reading from that address will - * return the last read value, which in our case is - * those of the man_id register. Likewise, the config1 - * register seems to lack a low nibble, so the value - * will be those of the previous read, so in our case - * those of the man_id register. + * The ADM1032 supports PEC, but only if combined + * transactions are not used. */ - if (chip_id == man_id - && (address == 0x4C || address == 0x4D) - && (reg_config1 & 0x1F) == (man_id & 0x0F) - && reg_convrate <= 0x09) { - kind = max6657; + if (i2c_check_functionality(adapter, + I2C_FUNC_SMBUS_BYTE)) + info->flags |= I2C_CLIENT_PEC; + } else + if (chip_id == 0x51 /* ADT7461 */ + && (config1 & 0x1B) == 0x00 + && convrate <= 0x0A) { + name = "adt7461"; + } else + if (chip_id == 0x57 /* ADT7461A, NCT1008 */ + && (config1 & 0x1B) == 0x00 + && convrate <= 0x0A) { + name = "adt7461a"; + } + } else + if (man_id == 0x4D) { /* Maxim */ + int emerg, emerg2, status2; + + /* + * We read MAX6659_REG_R_REMOTE_EMERG twice, and re-read + * LM90_REG_R_MAN_ID in between. If MAX6659_REG_R_REMOTE_EMERG + * exists, both readings will reflect the same value. Otherwise, + * the readings will be different. + */ + emerg = i2c_smbus_read_byte_data(client, + MAX6659_REG_R_REMOTE_EMERG); + man_id = i2c_smbus_read_byte_data(client, + LM90_REG_R_MAN_ID); + emerg2 = i2c_smbus_read_byte_data(client, + MAX6659_REG_R_REMOTE_EMERG); + status2 = i2c_smbus_read_byte_data(client, + MAX6696_REG_R_STATUS2); + if (emerg < 0 || man_id < 0 || emerg2 < 0 || status2 < 0) + return -ENODEV; + + /* + * The MAX6657, MAX6658 and MAX6659 do NOT have a chip_id + * register. Reading from that address will return the last + * read value, which in our case is those of the man_id + * register. Likewise, the config1 register seems to lack a + * low nibble, so the value will be those of the previous + * read, so in our case those of the man_id register. + * MAX6659 has a third set of upper temperature limit registers. + * Those registers also return values on MAX6657 and MAX6658, + * thus the only way to detect MAX6659 is by its address. + * For this reason it will be mis-detected as MAX6657 if its + * address is 0x4C. + */ + if (chip_id == man_id + && (address == 0x4C || address == 0x4D || address == 0x4E) + && (config1 & 0x1F) == (man_id & 0x0F) + && convrate <= 0x09) { + if (address == 0x4C) + name = "max6657"; + else + name = "max6659"; + } else + /* + * Even though MAX6695 and MAX6696 do not have a chip ID + * register, reading it returns 0x01. Bit 4 of the config1 + * register is unused and should return zero when read. Bit 0 of + * the status2 register is unused and should return zero when + * read. + * + * MAX6695 and MAX6696 have an additional set of temperature + * limit registers. We can detect those chips by checking if + * one of those registers exists. + */ + if (chip_id == 0x01 + && (config1 & 0x10) == 0x00 + && (status2 & 0x01) == 0x00 + && emerg == emerg2 + && convrate <= 0x07) { + name = "max6696"; + } else + /* + * The chip_id register of the MAX6680 and MAX6681 holds the + * revision of the chip. The lowest bit of the config1 register + * is unused and should return zero when read, so should the + * second to last bit of config1 (software reset). + */ + if (chip_id == 0x01 + && (config1 & 0x03) == 0x00 + && convrate <= 0x07) { + name = "max6680"; + } else + /* + * The chip_id register of the MAX6646/6647/6649 holds the + * revision of the chip. The lowest 6 bits of the config1 + * register are unused and should return zero when read. + */ + if (chip_id == 0x59 + && (config1 & 0x3f) == 0x00 + && convrate <= 0x07) { + name = "max6646"; + } + } else + if (address == 0x4C + && man_id == 0x5C) { /* Winbond/Nuvoton */ + if ((config1 & 0x2A) == 0x00 + && (config2 & 0xF8) == 0x00) { + if (chip_id == 0x01 /* W83L771W/G */ + && convrate <= 0x09) { + name = "w83l771"; } else - /* The chip_id register of the MAX6680 and MAX6681 - * holds the revision of the chip. - * the lowest bit of the config1 register is unused - * and should return zero when read, so should the - * second to last bit of config1 (software reset) - */ - if (chip_id == 0x01 - && (reg_config1 & 0x03) == 0x00 - && reg_convrate <= 0x07) { - kind = max6680; + if ((chip_id & 0xFE) == 0x10 /* W83L771AWG/ASG */ + && convrate <= 0x08) { + name = "w83l771"; } } - - if (kind <= 0) { /* identification failed */ - dev_info(&adapter->dev, - "Unsupported chip (man_id=0x%02X, " - "chip_id=0x%02X).\n", man_id, chip_id); - goto exit_free; + } else + if (address >= 0x48 && address <= 0x4F + && man_id == 0xA1) { /* NXP Semiconductor/Philips */ + if (chip_id == 0x00 + && (config1 & 0x2A) == 0x00 + && (config2 & 0xFE) == 0x00 + && convrate <= 0x09) { + name = "sa56004"; } + } else + if ((address == 0x4C || address == 0x4D) + && man_id == 0x47) { /* GMT */ + if (chip_id == 0x01 /* G781 */ + && (config1 & 0x3F) == 0x00 + && convrate <= 0x08) + name = "g781"; + } else + if (address == 0x4C + && man_id == 0x55) { /* Texas Instruments */ + int local_ext; + + local_ext = i2c_smbus_read_byte_data(client, + TMP451_REG_R_LOCAL_TEMPL); + + if (chip_id == 0x00 /* TMP451 */ + && (config1 & 0x1B) == 0x00 + && convrate <= 0x09 + && (local_ext & 0x0F) == 0x00) + name = "tmp451"; } - if (kind == lm90) { - name = "lm90"; - } else if (kind == adm1032) { - name = "adm1032"; - /* The ADM1032 supports PEC, but only if combined - transactions are not used. */ - if (i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) - new_client->flags |= I2C_CLIENT_PEC; - } else if (kind == lm99) { - name = "lm99"; - } else if (kind == lm86) { - name = "lm86"; - } else if (kind == max6657) { - name = "max6657"; - } else if (kind == max6680) { - name = "max6680"; - } else if (kind == adt7461) { - name = "adt7461"; + if (!name) { /* identification failed */ + dev_dbg(&adapter->dev, + "Unsupported chip at 0x%02x (man_id=0x%02X, " + "chip_id=0x%02X)\n", address, man_id, chip_id); + return -ENODEV; } - /* We can fill in the remaining client fields */ - strlcpy(new_client->name, name, I2C_NAME_SIZE); - data->valid = 0; - data->kind = kind; - mutex_init(&data->update_lock); - - /* Tell the I2C layer a new client has arrived */ - if ((err = i2c_attach_client(new_client))) - goto exit_free; - - /* Initialize the LM90 chip */ - lm90_init_client(new_client); - - /* Register sysfs hooks */ - if ((err = sysfs_create_group(&new_client->dev.kobj, &lm90_group))) - goto exit_detach; - if (new_client->flags & I2C_CLIENT_PEC) { - if ((err = device_create_file(&new_client->dev, - &dev_attr_pec))) - goto exit_remove_files; - } - if (data->kind != max6657) { - if ((err = device_create_file(&new_client->dev, - &sensor_dev_attr_temp2_offset.dev_attr))) - goto exit_remove_files; - } - - data->hwmon_dev = hwmon_device_register(&new_client->dev); - if (IS_ERR(data->hwmon_dev)) { - err = PTR_ERR(data->hwmon_dev); - goto exit_remove_files; - } + strlcpy(info->type, name, I2C_NAME_SIZE); return 0; +} -exit_remove_files: - sysfs_remove_group(&new_client->dev.kobj, &lm90_group); - device_remove_file(&new_client->dev, &dev_attr_pec); -exit_detach: - i2c_detach_client(new_client); -exit_free: - kfree(data); -exit: - return err; +static void lm90_restore_conf(struct i2c_client *client, struct lm90_data *data) +{ + /* Restore initial configuration */ + i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, + data->convrate_orig); + i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, + data->config_orig); } -static void lm90_init_client(struct i2c_client *client) +static void lm90_init_client(struct i2c_client *client, struct lm90_data *data) { - u8 config, config_orig; - struct lm90_data *data = i2c_get_clientdata(client); + u8 config, convrate; + + if (lm90_read_reg(client, LM90_REG_R_CONVRATE, &convrate) < 0) { + dev_warn(&client->dev, "Failed to read convrate register!\n"); + convrate = LM90_DEF_CONVRATE_RVAL; + } + data->convrate_orig = convrate; /* * Start the conversions. */ - i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, - 5); /* 2 Hz */ + lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */ if (lm90_read_reg(client, LM90_REG_R_CONFIG1, &config) < 0) { dev_warn(&client->dev, "Initialization failed!\n"); return; } - config_orig = config; + data->config_orig = config; + + /* Check Temperature Range Select */ + if (data->kind == adt7461 || data->kind == tmp451) { + if (config & 0x04) + data->flags |= LM90_FLAG_ADT7461_EXT; + } /* * Put MAX6680/MAX8881 into extended resolution (bit 0x10, * 0.125 degree resolution) and range (0x08, extend range * to -64 degree) mode for the remote temperature sensor. */ - if (data->kind == max6680) { + if (data->kind == max6680) config |= 0x18; - } + + /* + * Select external channel 0 for max6695/96 + */ + if (data->kind == max6696) + config &= ~0x08; config &= 0xBF; /* run */ - if (config != config_orig) /* Only write if changed */ + if (config != data->config_orig) /* Only write if changed */ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config); } -static int lm90_detach_client(struct i2c_client *client) +static bool lm90_is_tripped(struct i2c_client *client, u16 *status) { struct lm90_data *data = i2c_get_clientdata(client); + u8 st, st2 = 0; + + lm90_read_reg(client, LM90_REG_R_STATUS, &st); + + if (data->kind == max6696) + lm90_read_reg(client, MAX6696_REG_R_STATUS2, &st2); + + *status = st | (st2 << 8); + + if ((st & 0x7f) == 0 && (st2 & 0xfe) == 0) + return false; + + if ((st & (LM90_STATUS_LLOW | LM90_STATUS_LHIGH | LM90_STATUS_LTHRM)) || + (st2 & MAX6696_STATUS2_LOT2)) + dev_warn(&client->dev, + "temp%d out of range, please check!\n", 1); + if ((st & (LM90_STATUS_RLOW | LM90_STATUS_RHIGH | LM90_STATUS_RTHRM)) || + (st2 & MAX6696_STATUS2_ROT2)) + dev_warn(&client->dev, + "temp%d out of range, please check!\n", 2); + if (st & LM90_STATUS_ROPEN) + dev_warn(&client->dev, + "temp%d diode open, please check!\n", 2); + if (st2 & (MAX6696_STATUS2_R2LOW | MAX6696_STATUS2_R2HIGH | + MAX6696_STATUS2_R2THRM | MAX6696_STATUS2_R2OT2)) + dev_warn(&client->dev, + "temp%d out of range, please check!\n", 3); + if (st2 & MAX6696_STATUS2_R2OPEN) + dev_warn(&client->dev, + "temp%d diode open, please check!\n", 3); + + return true; +} + +static irqreturn_t lm90_irq_thread(int irq, void *dev_id) +{ + struct i2c_client *client = dev_id; + u16 status; + + if (lm90_is_tripped(client, &status)) + return IRQ_HANDLED; + else + return IRQ_NONE; +} + +static int lm90_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct i2c_adapter *adapter = to_i2c_adapter(dev->parent); + struct lm90_data *data; + struct regulator *regulator; + int groups = 0; int err; - hwmon_device_unregister(data->hwmon_dev); - sysfs_remove_group(&client->dev.kobj, &lm90_group); - device_remove_file(&client->dev, &dev_attr_pec); - if (data->kind != max6657) - device_remove_file(&client->dev, - &sensor_dev_attr_temp2_offset.dev_attr); + regulator = devm_regulator_get(dev, "vcc"); + if (IS_ERR(regulator)) + return PTR_ERR(regulator); - if ((err = i2c_detach_client(client))) + err = regulator_enable(regulator); + if (err < 0) { + dev_err(dev, "Failed to enable regulator: %d\n", err); return err; + } - kfree(data); - return 0; -} + data = devm_kzalloc(dev, sizeof(struct lm90_data), GFP_KERNEL); + if (!data) + return -ENOMEM; -static struct lm90_data *lm90_update_device(struct device *dev) -{ - struct i2c_client *client = to_i2c_client(dev); - struct lm90_data *data = i2c_get_clientdata(client); + data->client = client; + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); - mutex_lock(&data->update_lock); + data->regulator = regulator; - if (time_after(jiffies, data->last_updated + HZ * 2) || !data->valid) { - u8 oldh, newh, l; + /* Set the device type */ + data->kind = id->driver_data; + if (data->kind == adm1032) { + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) + client->flags &= ~I2C_CLIENT_PEC; + } - dev_dbg(&client->dev, "Updating lm90 data.\n"); - lm90_read_reg(client, LM90_REG_R_LOCAL_TEMP, &data->temp8[0]); - lm90_read_reg(client, LM90_REG_R_LOCAL_LOW, &data->temp8[1]); - lm90_read_reg(client, LM90_REG_R_LOCAL_HIGH, &data->temp8[2]); - lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT, &data->temp8[3]); - lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT, &data->temp8[4]); - lm90_read_reg(client, LM90_REG_R_TCRIT_HYST, &data->temp_hyst); + /* + * Different devices have different alarm bits triggering the + * ALERT# output + */ + data->alert_alarms = lm90_params[data->kind].alert_alarms; - /* - * There is a trick here. We have to read two registers to - * have the remote sensor temperature, but we have to beware - * a conversion could occur inbetween the readings. The - * datasheet says we should either use the one-shot - * conversion register, which we don't want to do (disables - * hardware monitoring) or monitor the busy bit, which is - * impossible (we can't read the values and monitor that bit - * at the exact same time). So the solution used here is to - * read the high byte once, then the low byte, then the high - * byte again. If the new high byte matches the old one, - * then we have a valid reading. Else we have to read the low - * byte again, and now we believe we have a correct reading. - */ - if (lm90_read_reg(client, LM90_REG_R_REMOTE_TEMPH, &oldh) == 0 - && lm90_read_reg(client, LM90_REG_R_REMOTE_TEMPL, &l) == 0 - && lm90_read_reg(client, LM90_REG_R_REMOTE_TEMPH, &newh) == 0 - && (newh == oldh - || lm90_read_reg(client, LM90_REG_R_REMOTE_TEMPL, &l) == 0)) - data->temp11[0] = (newh << 8) | l; - - if (lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &newh) == 0 - && lm90_read_reg(client, LM90_REG_R_REMOTE_LOWL, &l) == 0) - data->temp11[1] = (newh << 8) | l; - if (lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &newh) == 0 - && lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHL, &l) == 0) - data->temp11[2] = (newh << 8) | l; - if (data->kind != max6657) { - if (lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSH, - &newh) == 0 - && lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSL, - &l) == 0) - data->temp11[3] = (newh << 8) | l; - } - lm90_read_reg(client, LM90_REG_R_STATUS, &data->alarms); + /* Set chip capabilities */ + data->flags = lm90_params[data->kind].flags; + data->reg_local_ext = lm90_params[data->kind].reg_local_ext; - data->last_updated = jiffies; - data->valid = 1; + /* Set maximum conversion rate */ + data->max_convrate = lm90_params[data->kind].max_convrate; + + /* Initialize the LM90 chip */ + lm90_init_client(client, data); + + /* Register sysfs hooks */ + data->groups[groups++] = &lm90_group; + + if (data->flags & LM90_HAVE_OFFSET) + data->groups[groups++] = &lm90_temp2_offset_group; + + if (data->flags & LM90_HAVE_EMERGENCY) + data->groups[groups++] = &lm90_emergency_group; + + if (data->flags & LM90_HAVE_EMERGENCY_ALARM) + data->groups[groups++] = &lm90_emergency_alarm_group; + + if (data->flags & LM90_HAVE_TEMP3) + data->groups[groups++] = &lm90_temp3_group; + + if (client->flags & I2C_CLIENT_PEC) { + err = device_create_file(dev, &dev_attr_pec); + if (err) + goto exit_restore; } - mutex_unlock(&data->update_lock); + data->hwmon_dev = hwmon_device_register_with_groups(dev, client->name, + data, data->groups); + if (IS_ERR(data->hwmon_dev)) { + err = PTR_ERR(data->hwmon_dev); + goto exit_remove_pec; + } - return data; + if (client->irq) { + dev_dbg(dev, "IRQ: %d\n", client->irq); + err = devm_request_threaded_irq(dev, client->irq, + NULL, lm90_irq_thread, + IRQF_TRIGGER_LOW | IRQF_ONESHOT, + "lm90", client); + if (err < 0) { + dev_err(dev, "cannot request IRQ %d\n", client->irq); + goto exit_unregister; + } + } + + return 0; + +exit_unregister: + hwmon_device_unregister(data->hwmon_dev); +exit_remove_pec: + device_remove_file(dev, &dev_attr_pec); +exit_restore: + lm90_restore_conf(client, data); + regulator_disable(data->regulator); + + return err; } -static int __init sensors_lm90_init(void) +static int lm90_remove(struct i2c_client *client) { - return i2c_add_driver(&lm90_driver); + struct lm90_data *data = i2c_get_clientdata(client); + + hwmon_device_unregister(data->hwmon_dev); + device_remove_file(&client->dev, &dev_attr_pec); + lm90_restore_conf(client, data); + regulator_disable(data->regulator); + + return 0; } -static void __exit sensors_lm90_exit(void) +static void lm90_alert(struct i2c_client *client, unsigned int flag) { - i2c_del_driver(&lm90_driver); + u16 alarms; + + if (lm90_is_tripped(client, &alarms)) { + /* + * Disable ALERT# output, because these chips don't implement + * SMBus alert correctly; they should only hold the alert line + * low briefly. + */ + struct lm90_data *data = i2c_get_clientdata(client); + + if ((data->flags & LM90_HAVE_BROKEN_ALERT) + && (alarms & data->alert_alarms)) { + u8 config; + dev_dbg(&client->dev, "Disabling ALERT#\n"); + lm90_read_reg(client, LM90_REG_R_CONFIG1, &config); + i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, + config | 0x80); + } + } else { + dev_info(&client->dev, "Everything OK\n"); + } } -MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); +static struct i2c_driver lm90_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "lm90", + }, + .probe = lm90_probe, + .remove = lm90_remove, + .alert = lm90_alert, + .id_table = lm90_id, + .detect = lm90_detect, + .address_list = normal_i2c, +}; + +module_i2c_driver(lm90_driver); + +MODULE_AUTHOR("Jean Delvare <jdelvare@suse.de>"); MODULE_DESCRIPTION("LM90/ADM1032 driver"); MODULE_LICENSE("GPL"); - -module_init(sensors_lm90_init); -module_exit(sensors_lm90_exit); |