diff options
Diffstat (limited to 'drivers/char/ip2/i2pack.h')
| -rw-r--r-- | drivers/char/ip2/i2pack.h | 364 |
1 files changed, 0 insertions, 364 deletions
diff --git a/drivers/char/ip2/i2pack.h b/drivers/char/ip2/i2pack.h deleted file mode 100644 index 00342a677c9..00000000000 --- a/drivers/char/ip2/i2pack.h +++ /dev/null @@ -1,364 +0,0 @@ -/******************************************************************************* -* -* (c) 1998 by Computone Corporation -* -******************************************************************************** -* -* -* PACKAGE: Linux tty Device Driver for IntelliPort II family of multiport -* serial I/O controllers. -* -* DESCRIPTION: Definitions of the packets used to transfer data and commands -* Host <--> Board. Information provided here is only applicable -* when the standard loadware is active. -* -*******************************************************************************/ -#ifndef I2PACK_H -#define I2PACK_H 1 - -//----------------------------------------------- -// Revision History: -// -// 10 October 1991 MAG First draft -// 24 February 1992 MAG Additions for 1.4.x loadware -// 11 March 1992 MAG New status packets -// -//----------------------------------------------- - -//------------------------------------------------------------------------------ -// Packet Formats: -// -// Information passes between the host and board through the FIFO in packets. -// These have headers which indicate the type of packet. Because the fifo data -// path may be 16-bits wide, the protocol is constrained such that each packet -// is always padded to an even byte count. (The lower-level interface routines -// -- i2ellis.c -- are designed to do this). -// -// The sender (be it host or board) must place some number of complete packets -// in the fifo, then place a message in the mailbox that packets are available. -// Placing such a message interrupts the "receiver" (be it board or host), who -// reads the mailbox message and determines that there are incoming packets -// ready. Since there are no partial packets, and the length of a packet is -// given in the header, the remainder of the packet can be read without checking -// for FIFO empty condition. The process is repeated, packet by packet, until -// the incoming FIFO is empty. Then the receiver uses the outbound mailbox to -// signal the board that it has read the data. Only then can the sender place -// additional data in the fifo. -//------------------------------------------------------------------------------ -// -//------------------------------------------------ -// Definition of Packet Header Area -//------------------------------------------------ -// -// Caution: these only define header areas. In actual use the data runs off -// beyond the end of these structures. -// -// Since these structures are based on sequences of bytes which go to the board, -// there cannot be ANY padding between the elements. -#pragma pack(1) - -//---------------------------- -// DATA PACKETS -//---------------------------- - -typedef struct _i2DataHeader -{ - unsigned char i2sChannel; /* The channel number: 0-255 */ - - // -- Bitfields are allocated LSB first -- - - // For incoming data, indicates whether this is an ordinary packet or a - // special one (e.g., hot key hit). - unsigned i2sId : 2 __attribute__ ((__packed__)); - - // For tagging data packets. There are flush commands which flush only data - // packets bearing a particular tag. (used in implementing IntelliView and - // IntelliPrint). THE TAG VALUE 0xf is RESERVED and must not be used (it has - // meaning internally to the loadware). - unsigned i2sTag : 4; - - // These two bits determine the type of packet sent/received. - unsigned i2sType : 2; - - // The count of data to follow: does not include the possible additional - // padding byte. MAXIMUM COUNT: 4094. The top four bits must be 0. - unsigned short i2sCount; - -} i2DataHeader, *i2DataHeaderPtr; - -// Structure is immediately followed by the data, proper. - -//---------------------------- -// NON-DATA PACKETS -//---------------------------- - -typedef struct _i2CmdHeader -{ - unsigned char i2sChannel; // The channel number: 0-255 (Except where noted - // - see below - - // Number of bytes of commands, status or whatever to follow - unsigned i2sCount : 6; - - // These two bits determine the type of packet sent/received. - unsigned i2sType : 2; - -} i2CmdHeader, *i2CmdHeaderPtr; - -// Structure is immediately followed by the applicable data. - -//--------------------------------------- -// Flow Control Packets (Outbound) -//--------------------------------------- - -// One type of outbound command packet is so important that the entire structure -// is explicitly defined here. That is the flow-control packet. This is never -// sent by user-level code (as would be the commands to raise/lower DTR, for -// example). These are only sent by the library routines in response to reading -// incoming data into the buffers. -// -// The parameters inside the command block are maintained in place, then the -// block is sent at the appropriate time. - -typedef struct _flowIn -{ - i2CmdHeader hd; // Channel #, count, type (see above) - unsigned char fcmd; // The flow control command (37) - unsigned short asof; // As of byte number "asof" (LSB first!) I have room - // for "room" bytes - unsigned short room; -} flowIn, *flowInPtr; - -//---------------------------------------- -// (Incoming) Status Packets -//---------------------------------------- - -// Incoming packets which are non-data packets are status packets. In this case, -// the channel number in the header is unimportant. What follows are one or more -// sub-packets, the first word of which consists of the channel (first or low -// byte) and the status indicator (second or high byte), followed by possibly -// more data. - -#define STAT_CTS_UP 0 /* CTS raised (no other bytes) */ -#define STAT_CTS_DN 1 /* CTS dropped (no other bytes) */ -#define STAT_DCD_UP 2 /* DCD raised (no other bytes) */ -#define STAT_DCD_DN 3 /* DCD dropped (no other bytes) */ -#define STAT_DSR_UP 4 /* DSR raised (no other bytes) */ -#define STAT_DSR_DN 5 /* DSR dropped (no other bytes) */ -#define STAT_RI_UP 6 /* RI raised (no other bytes) */ -#define STAT_RI_DN 7 /* RI dropped (no other bytes) */ -#define STAT_BRK_DET 8 /* BRK detect (no other bytes) */ -#define STAT_FLOW 9 /* Flow control(-- more: see below */ -#define STAT_BMARK 10 /* Bookmark (no other bytes) - * Bookmark is sent as a response to - * a command 60: request for bookmark - */ -#define STAT_STATUS 11 /* Special packet: see below */ -#define STAT_TXCNT 12 /* Special packet: see below */ -#define STAT_RXCNT 13 /* Special packet: see below */ -#define STAT_BOXIDS 14 /* Special packet: see below */ -#define STAT_HWFAIL 15 /* Special packet: see below */ - -#define STAT_MOD_ERROR 0xc0 -#define STAT_MODEM 0xc0/* If status & STAT_MOD_ERROR: - * == STAT_MODEM, then this is a modem - * status packet, given in response to a - * CMD_DSS_NOW command. - * The low nibble has each data signal: - */ -#define STAT_MOD_DCD 0x8 -#define STAT_MOD_RI 0x4 -#define STAT_MOD_DSR 0x2 -#define STAT_MOD_CTS 0x1 - -#define STAT_ERROR 0x80/* If status & STAT_MOD_ERROR - * == STAT_ERROR, then - * sort of error on the channel. - * The remaining seven bits indicate - * what sort of error it is. - */ -/* The low three bits indicate parity, framing, or overrun errors */ - -#define STAT_E_PARITY 4 /* Parity error */ -#define STAT_E_FRAMING 2 /* Framing error */ -#define STAT_E_OVERRUN 1 /* (uxart) overrun error */ - -//--------------------------------------- -// STAT_FLOW packets -//--------------------------------------- - -typedef struct _flowStat -{ - unsigned short asof; - unsigned short room; -}flowStat, *flowStatPtr; - -// flowStat packets are received from the board to regulate the flow of outgoing -// data. A local copy of this structure is also kept to track the amount of -// credits used and credits remaining. "room" is the amount of space in the -// board's buffers, "as of" having received a certain byte number. When sending -// data to the fifo, you must calculate how much buffer space your packet will -// use. Add this to the current "asof" and subtract it from the current "room". -// -// The calculation for the board's buffer is given by CREDIT_USAGE, where size -// is the un-rounded count of either data characters or command characters. -// (Which is to say, the count rounded up, plus two). - -#define CREDIT_USAGE(size) (((size) + 3) & ~1) - -//--------------------------------------- -// STAT_STATUS packets -//--------------------------------------- - -typedef struct _debugStat -{ - unsigned char d_ccsr; - unsigned char d_txinh; - unsigned char d_stat1; - unsigned char d_stat2; -} debugStat, *debugStatPtr; - -// debugStat packets are sent to the host in response to a CMD_GET_STATUS -// command. Each byte is bit-mapped as described below: - -#define D_CCSR_XON 2 /* Has received XON, ready to transmit */ -#define D_CCSR_XOFF 4 /* Has received XOFF, not transmitting */ -#define D_CCSR_TXENAB 8 /* Transmitter is enabled */ -#define D_CCSR_RXENAB 0x80 /* Receiver is enabled */ - -#define D_TXINH_BREAK 1 /* We are sending a break */ -#define D_TXINH_EMPTY 2 /* No data to send */ -#define D_TXINH_SUSP 4 /* Output suspended via command 57 */ -#define D_TXINH_CMD 8 /* We are processing an in-line command */ -#define D_TXINH_LCD 0x10 /* LCD diagnostics are running */ -#define D_TXINH_PAUSE 0x20 /* We are processing a PAUSE command */ -#define D_TXINH_DCD 0x40 /* DCD is low, preventing transmission */ -#define D_TXINH_DSR 0x80 /* DSR is low, preventing transmission */ - -#define D_STAT1_TXEN 1 /* Transmit INTERRUPTS enabled */ -#define D_STAT1_RXEN 2 /* Receiver INTERRUPTS enabled */ -#define D_STAT1_MDEN 4 /* Modem (data set sigs) interrupts enabled */ -#define D_STAT1_RLM 8 /* Remote loopback mode selected */ -#define D_STAT1_LLM 0x10 /* Local internal loopback mode selected */ -#define D_STAT1_CTS 0x20 /* CTS is low, preventing transmission */ -#define D_STAT1_DTR 0x40 /* DTR is low, to stop remote transmission */ -#define D_STAT1_RTS 0x80 /* RTS is low, to stop remote transmission */ - -#define D_STAT2_TXMT 1 /* Transmit buffers are all empty */ -#define D_STAT2_RXMT 2 /* Receive buffers are all empty */ -#define D_STAT2_RXINH 4 /* Loadware has tried to inhibit remote - * transmission: dropped DTR, sent XOFF, - * whatever... - */ -#define D_STAT2_RXFLO 8 /* Loadware can send no more data to host - * until it receives a flow-control packet - */ -//----------------------------------------- -// STAT_TXCNT and STAT_RXCNT packets -//---------------------------------------- - -typedef struct _cntStat -{ - unsigned short cs_time; // (Assumes host is little-endian!) - unsigned short cs_count; -} cntStat, *cntStatPtr; - -// These packets are sent in response to a CMD_GET_RXCNT or a CMD_GET_TXCNT -// bypass command. cs_time is a running 1 Millisecond counter which acts as a -// time stamp. cs_count is a running counter of data sent or received from the -// uxarts. (Not including data added by the chip itself, as with CRLF -// processing). -//------------------------------------------ -// STAT_HWFAIL packets -//------------------------------------------ - -typedef struct _failStat -{ - unsigned char fs_written; - unsigned char fs_read; - unsigned short fs_address; -} failStat, *failStatPtr; - -// This packet is sent whenever the on-board diagnostic process detects an -// error. At startup, this process is dormant. The host can wake it up by -// issuing the bypass command CMD_HW_TEST. The process runs at low priority and -// performs continuous hardware verification; writing data to certain on-board -// registers, reading it back, and comparing. If it detects an error, this -// packet is sent to the host, and the process goes dormant again until the host -// sends another CMD_HW_TEST. It then continues with the next register to be -// tested. - -//------------------------------------------------------------------------------ -// Macros to deal with the headers more easily! Note that these are defined so -// they may be used as "left" as well as "right" expressions. -//------------------------------------------------------------------------------ - -// Given a pointer to the packet, reference the channel number -// -#define CHANNEL_OF(pP) ((i2DataHeaderPtr)(pP))->i2sChannel - -// Given a pointer to the packet, reference the Packet type -// -#define PTYPE_OF(pP) ((i2DataHeaderPtr)(pP))->i2sType - -// The possible types of packets -// -#define PTYPE_DATA 0 /* Host <--> Board */ -#define PTYPE_BYPASS 1 /* Host ---> Board */ -#define PTYPE_INLINE 2 /* Host ---> Board */ -#define PTYPE_STATUS 2 /* Host <--- Board */ - -// Given a pointer to a Data packet, reference the Tag -// -#define TAG_OF(pP) ((i2DataHeaderPtr)(pP))->i2sTag - -// Given a pointer to a Data packet, reference the data i.d. -// -#define ID_OF(pP) ((i2DataHeaderPtr)(pP))->i2sId - -// The possible types of ID's -// -#define ID_ORDINARY_DATA 0 -#define ID_HOT_KEY 1 - -// Given a pointer to a Data packet, reference the count -// -#define DATA_COUNT_OF(pP) ((i2DataHeaderPtr)(pP))->i2sCount - -// Given a pointer to a Data packet, reference the beginning of data -// -#define DATA_OF(pP) &((unsigned char *)(pP))[4] // 4 = size of header - -// Given a pointer to a Non-Data packet, reference the count -// -#define CMD_COUNT_OF(pP) ((i2CmdHeaderPtr)(pP))->i2sCount - -#define MAX_CMD_PACK_SIZE 62 // Maximum size of such a count - -// Given a pointer to a Non-Data packet, reference the beginning of data -// -#define CMD_OF(pP) &((unsigned char *)(pP))[2] // 2 = size of header - -//-------------------------------- -// MailBox Bits: -//-------------------------------- - -//-------------------------- -// Outgoing (host to board) -//-------------------------- -// -#define MB_OUT_STUFFED 0x80 // Host has placed output in fifo -#define MB_IN_STRIPPED 0x40 // Host has read in all input from fifo - -//-------------------------- -// Incoming (board to host) -//-------------------------- -// -#define MB_IN_STUFFED 0x80 // Board has placed input in fifo -#define MB_OUT_STRIPPED 0x40 // Board has read all output from fifo -#define MB_FATAL_ERROR 0x20 // Board has encountered a fatal error - -#pragma pack() // Reset padding to command-line default - -#endif // I2PACK_H - |