aboutsummaryrefslogtreecommitdiff
path: root/drivers/atm/lanai.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/atm/lanai.c')
-rw-r--r--drivers/atm/lanai.c229
1 files changed, 50 insertions, 179 deletions
diff --git a/drivers/atm/lanai.c b/drivers/atm/lanai.c
index 51ec1478729..fa7d701933b 100644
--- a/drivers/atm/lanai.c
+++ b/drivers/atm/lanai.c
@@ -39,7 +39,7 @@
* o lanai_change_qos() isn't written yet
*
* o There aren't any ioctl's yet -- I'd like to eventually support
- * setting loopback and LED modes that way. (see lanai_ioctl)
+ * setting loopback and LED modes that way.
*
* o If the segmentation engine or DMA gets shut down we should restart
* card as per section 17.0i. (see lanai_reset)
@@ -55,6 +55,7 @@
*/
#include <linux/module.h>
+#include <linux/slab.h>
#include <linux/mm.h>
#include <linux/atmdev.h>
#include <asm/io.h>
@@ -65,7 +66,6 @@
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
-#include <linux/dma-mapping.h>
/* -------------------- TUNABLE PARAMATERS: */
@@ -246,8 +246,8 @@ struct lanai_vcc {
};
enum lanai_type {
- lanai2 = PCI_VENDOR_ID_EF_ATM_LANAI2,
- lanaihb = PCI_VENDOR_ID_EF_ATM_LANAIHB
+ lanai2 = PCI_DEVICE_ID_EF_ATM_LANAI2,
+ lanaihb = PCI_DEVICE_ID_EF_ATM_LANAIHB
};
struct lanai_dev_stats {
@@ -293,7 +293,6 @@ struct lanai_dev {
struct atm_vcc *cbrvcc;
int number;
int board_rev;
- u8 pci_revision;
/* TODO - look at race conditions with maintence of conf1/conf2 */
/* TODO - transmit locking: should we use _irq not _irqsave? */
/* TODO - organize above in some rational fashion (see <asm/cache.h>) */
@@ -305,14 +304,13 @@ struct lanai_dev {
* vci with their bit set
*/
static void vci_bitfield_iterate(struct lanai_dev *lanai,
- /*const*/ unsigned long *lp,
+ const unsigned long *lp,
void (*func)(struct lanai_dev *,vci_t vci))
{
- vci_t vci = find_first_bit(lp, NUM_VCI);
- while (vci < NUM_VCI) {
+ vci_t vci;
+
+ for_each_set_bit(vci, lp, NUM_VCI)
func(lanai, vci);
- vci = find_next_bit(lp, NUM_VCI, vci + 1);
- }
}
/* -------------------- BUFFER UTILITIES: */
@@ -553,8 +551,8 @@ static inline void sram_write(const struct lanai_dev *lanai,
writel(val, sram_addr(lanai, offset));
}
-static int __init sram_test_word(
- const struct lanai_dev *lanai, int offset, u32 pattern)
+static int sram_test_word(const struct lanai_dev *lanai, int offset,
+ u32 pattern)
{
u32 readback;
sram_write(lanai, pattern, offset);
@@ -568,7 +566,7 @@ static int __init sram_test_word(
return -EIO;
}
-static int __devinit sram_test_pass(const struct lanai_dev *lanai, u32 pattern)
+static int sram_test_pass(const struct lanai_dev *lanai, u32 pattern)
{
int offset, result = 0;
for (offset = 0; offset < SRAM_BYTES && result == 0; offset += 4)
@@ -576,7 +574,7 @@ static int __devinit sram_test_pass(const struct lanai_dev *lanai, u32 pattern)
return result;
}
-static int __devinit sram_test_and_clear(const struct lanai_dev *lanai)
+static int sram_test_and_clear(const struct lanai_dev *lanai)
{
#ifdef FULL_MEMORY_TEST
int result;
@@ -862,7 +860,7 @@ static inline void aal0_buffer_free(struct lanai_dev *lanai)
#ifndef READ_EEPROM
/* Stub functions to use if EEPROM reading is disabled */
-static int __devinit eeprom_read(struct lanai_dev *lanai)
+static int eeprom_read(struct lanai_dev *lanai)
{
printk(KERN_INFO DEV_LABEL "(itf %d): *NOT* reading EEPROM\n",
lanai->number);
@@ -870,7 +868,7 @@ static int __devinit eeprom_read(struct lanai_dev *lanai)
return 0;
}
-static int __devinit eeprom_validate(struct lanai_dev *lanai)
+static int eeprom_validate(struct lanai_dev *lanai)
{
lanai->serialno = 0;
lanai->magicno = EEPROM_MAGIC_VALUE;
@@ -879,7 +877,7 @@ static int __devinit eeprom_validate(struct lanai_dev *lanai)
#else /* READ_EEPROM */
-static int __devinit eeprom_read(struct lanai_dev *lanai)
+static int eeprom_read(struct lanai_dev *lanai)
{
int i, address;
u8 data;
@@ -903,7 +901,7 @@ static int __devinit eeprom_read(struct lanai_dev *lanai)
clock_l(); udelay(5);
for (i = 128; i != 0; i >>= 1) { /* write command out */
tmp = (lanai->conf1 & ~CONFIG1_PROMDATA) |
- (data & i) ? CONFIG1_PROMDATA : 0;
+ ((data & i) ? CONFIG1_PROMDATA : 0);
if (lanai->conf1 != tmp) {
set_config1(tmp);
udelay(5); /* Let new data settle */
@@ -951,11 +949,11 @@ static int __devinit eeprom_read(struct lanai_dev *lanai)
/* read a big-endian 4-byte value out of eeprom */
static inline u32 eeprom_be4(const struct lanai_dev *lanai, int address)
{
- return be32_to_cpup((u32 *) (&lanai->eeprom[address]));
+ return be32_to_cpup((const u32 *) &lanai->eeprom[address]);
}
/* Checksum/validate EEPROM contents */
-static int __devinit eeprom_validate(struct lanai_dev *lanai)
+static int eeprom_validate(struct lanai_dev *lanai)
{
int i, s;
u32 v;
@@ -1000,9 +998,7 @@ static int __devinit eeprom_validate(struct lanai_dev *lanai)
(unsigned int) e[EEPROM_MAC_REV + i]);
return -EIO;
}
- DPRINTK("eeprom: MAC address = %02X:%02X:%02X:%02X:%02X:%02X\n",
- e[EEPROM_MAC + 0], e[EEPROM_MAC + 1], e[EEPROM_MAC + 2],
- e[EEPROM_MAC + 3], e[EEPROM_MAC + 4], e[EEPROM_MAC + 5]);
+ DPRINTK("eeprom: MAC address = %pM\n", &e[EEPROM_MAC]);
/* Verify serial number */
lanai->serialno = eeprom_be4(lanai, EEPROM_SERIAL);
v = eeprom_be4(lanai, EEPROM_SERIAL_REV);
@@ -1160,7 +1156,7 @@ static inline int vcc_tx_space(const struct lanai_vcc *lvcc, int endptr)
}
/* test if VCC is currently backlogged */
-static inline int vcc_is_backlogged(/*const*/ struct lanai_vcc *lvcc)
+static inline int vcc_is_backlogged(const struct lanai_vcc *lvcc)
{
return !skb_queue_empty(&lvcc->tx.backlog);
}
@@ -1259,7 +1255,7 @@ static inline void lanai_endtx(struct lanai_dev *lanai,
/*
* Since the "butt register" is a shared resounce on the card we
* serialize all accesses to it through this spinlock. This is
- * mostly just paranoia sicne the register is rarely "busy" anyway
+ * mostly just paranoia since the register is rarely "busy" anyway
* but is needed for correctness.
*/
spin_lock(&lanai->endtxlock);
@@ -1395,7 +1391,8 @@ static void vcc_rx_aal5(struct lanai_vcc *lvcc, int endptr)
{
int size;
struct sk_buff *skb;
- /*const*/ u32 *x, *end = &lvcc->rx.buf.start[endptr * 4];
+ const u32 *x;
+ u32 *end = &lvcc->rx.buf.start[endptr * 4];
int n = ((unsigned long) end) - ((unsigned long) lvcc->rx.buf.ptr);
if (n < 0)
n += lanai_buf_size(&lvcc->rx.buf);
@@ -1451,7 +1448,7 @@ static void vcc_rx_aal0(struct lanai_dev *lanai)
#include <linux/vmalloc.h>
#endif
-static int __devinit vcc_table_allocate(struct lanai_dev *lanai)
+static int vcc_table_allocate(struct lanai_dev *lanai)
{
#ifdef VCCTABLE_GETFREEPAGE
APRINTK((lanai->num_vci) * sizeof(struct lanai_vcc *) <= PAGE_SIZE,
@@ -1460,10 +1457,9 @@ static int __devinit vcc_table_allocate(struct lanai_dev *lanai)
return (lanai->vccs == NULL) ? -ENOMEM : 0;
#else
int bytes = (lanai->num_vci) * sizeof(struct lanai_vcc *);
- lanai->vccs = (struct lanai_vcc **) vmalloc(bytes);
+ lanai->vccs = vzalloc(bytes);
if (unlikely(lanai->vccs == NULL))
return -ENOMEM;
- memset(lanai->vccs, 0, bytes);
return 0;
#endif
}
@@ -1481,16 +1477,10 @@ static inline void vcc_table_deallocate(const struct lanai_dev *lanai)
static inline struct lanai_vcc *new_lanai_vcc(void)
{
struct lanai_vcc *lvcc;
- lvcc = (struct lanai_vcc *) kmalloc(sizeof(*lvcc), GFP_KERNEL);
+ lvcc = kzalloc(sizeof(*lvcc), GFP_KERNEL);
if (likely(lvcc != NULL)) {
- lvcc->vbase = NULL;
- lvcc->rx.atmvcc = lvcc->tx.atmvcc = NULL;
- lvcc->nref = 0;
- memset(&lvcc->stats, 0, sizeof lvcc->stats);
- lvcc->rx.buf.start = lvcc->tx.buf.start = NULL;
skb_queue_head_init(&lvcc->tx.backlog);
#ifdef DEBUG
- lvcc->tx.unqueue = NULL;
lvcc->vci = -1;
#endif
}
@@ -1582,7 +1572,7 @@ static inline void host_vcc_unbind(struct lanai_dev *lanai,
static void lanai_reset(struct lanai_dev *lanai)
{
- printk(KERN_CRIT DEV_LABEL "(itf %d): *NOT* reseting - not "
+ printk(KERN_CRIT DEV_LABEL "(itf %d): *NOT* resetting - not "
"implemented\n", lanai->number);
/* TODO */
/* The following is just a hack until we write the real
@@ -1598,7 +1588,7 @@ static void lanai_reset(struct lanai_dev *lanai)
/*
* Allocate service buffer and tell card about it
*/
-static int __devinit service_buffer_allocate(struct lanai_dev *lanai)
+static int service_buffer_allocate(struct lanai_dev *lanai)
{
lanai_buf_allocate(&lanai->service, SERVICE_ENTRIES * 4, 8,
lanai->pci);
@@ -1895,13 +1885,11 @@ static inline void lanai_int_1(struct lanai_dev *lanai, u32 reason)
reg_write(lanai, ack, IntAck_Reg);
}
-static irqreturn_t lanai_int(int irq, void *devid, struct pt_regs *regs)
+static irqreturn_t lanai_int(int irq, void *devid)
{
- struct lanai_dev *lanai = (struct lanai_dev *) devid;
+ struct lanai_dev *lanai = devid;
u32 reason;
- (void) irq; (void) regs; /* unused variables */
-
#ifdef USE_POWERDOWN
/*
* If we're powered down we shouldn't be generating any interrupts -
@@ -1954,11 +1942,10 @@ static int check_board_id_and_rev(const char *name, u32 val, int *revp)
/* -------------------- PCI INITIALIZATION/SHUTDOWN: */
-static int __devinit lanai_pci_start(struct lanai_dev *lanai)
+static int lanai_pci_start(struct lanai_dev *lanai)
{
struct pci_dev *pci = lanai->pci;
int result;
- u16 w;
if (pci_enable_device(pci) != 0) {
printk(KERN_ERR DEV_LABEL "(itf %d): can't enable "
@@ -1966,31 +1953,17 @@ static int __devinit lanai_pci_start(struct lanai_dev *lanai)
return -ENXIO;
}
pci_set_master(pci);
- if (pci_set_dma_mask(pci, DMA_32BIT_MASK) != 0) {
+ if (pci_set_dma_mask(pci, DMA_BIT_MASK(32)) != 0) {
printk(KERN_WARNING DEV_LABEL
"(itf %d): No suitable DMA available.\n", lanai->number);
return -EBUSY;
}
- if (pci_set_consistent_dma_mask(pci, 0xFFFFFFFF) != 0) {
+ if (pci_set_consistent_dma_mask(pci, DMA_BIT_MASK(32)) != 0) {
printk(KERN_WARNING DEV_LABEL
"(itf %d): No suitable DMA available.\n", lanai->number);
return -EBUSY;
}
- /* Get the pci revision byte */
- result = pci_read_config_byte(pci, PCI_REVISION_ID,
- &lanai->pci_revision);
- if (result != PCIBIOS_SUCCESSFUL) {
- printk(KERN_ERR DEV_LABEL "(itf %d): can't read "
- "PCI_REVISION_ID: %d\n", lanai->number, result);
- return -EINVAL;
- }
- result = pci_read_config_word(pci, PCI_SUBSYSTEM_ID, &w);
- if (result != PCIBIOS_SUCCESSFUL) {
- printk(KERN_ERR DEV_LABEL "(itf %d): can't read "
- "PCI_SUBSYSTEM_ID: %d\n", lanai->number, result);
- return -EINVAL;
- }
- result = check_board_id_and_rev("PCI", w, NULL);
+ result = check_board_id_and_rev("PCI", pci->subsystem_device, NULL);
if (result != 0)
return result;
/* Set latency timer to zero as per lanai docs */
@@ -2009,7 +1982,7 @@ static int __devinit lanai_pci_start(struct lanai_dev *lanai)
/*
* We _can_ use VCI==0 for normal traffic, but only for UBR (or we'll
- * get a CBRZERO interrupt), and we can use it only if noone is receiving
+ * get a CBRZERO interrupt), and we can use it only if no one is receiving
* AAL0 traffic (since they will use the same queue) - according to the
* docs we shouldn't even use it for AAL0 traffic
*/
@@ -2111,7 +2084,7 @@ static int lanai_normalize_ci(struct lanai_dev *lanai,
* shifted by that much as we compute
*
*/
-static int pcr_to_cbricg(/*const*/ struct atm_qos *qos)
+static int pcr_to_cbricg(const struct atm_qos *qos)
{
int rounddown = 0; /* 1 = Round PCR down, i.e. round ICG _up_ */
int x, icg, pcr = atm_pcr_goal(&qos->txtp);
@@ -2150,7 +2123,7 @@ static inline void lanai_cbr_shutdown(struct lanai_dev *lanai)
/* -------------------- OPERATIONS: */
/* setup a newly detected device */
-static int __devinit lanai_dev_open(struct atm_dev *atmdev)
+static int lanai_dev_open(struct atm_dev *atmdev)
{
struct lanai_dev *lanai = (struct lanai_dev *) atmdev->dev_data;
unsigned long raw_base;
@@ -2239,7 +2212,7 @@ static int __devinit lanai_dev_open(struct atm_dev *atmdev)
conf2_write(lanai);
reg_write(lanai, TX_FIFO_DEPTH, TxDepth_Reg);
reg_write(lanai, 0, CBR_ICG_Reg); /* CBR defaults to no limit */
- if ((result = request_irq(lanai->pci->irq, lanai_int, SA_SHIRQ,
+ if ((result = request_irq(lanai->pci->irq, lanai_int, IRQF_SHARED,
DEV_LABEL, lanai)) != 0) {
printk(KERN_ERR DEV_LABEL ": can't allocate interrupt\n");
goto error_vcctable;
@@ -2260,11 +2233,8 @@ static int __devinit lanai_dev_open(struct atm_dev *atmdev)
memcpy(atmdev->esi, eeprom_mac(lanai), ESI_LEN);
lanai_timed_poll_start(lanai);
printk(KERN_NOTICE DEV_LABEL "(itf %d): rev.%d, base=0x%lx, irq=%u "
- "(%02X-%02X-%02X-%02X-%02X-%02X)\n", lanai->number,
- (int) lanai->pci_revision, (unsigned long) lanai->base,
- lanai->pci->irq,
- atmdev->esi[0], atmdev->esi[1], atmdev->esi[2],
- atmdev->esi[3], atmdev->esi[4], atmdev->esi[5]);
+ "(%pMF)\n", lanai->number, (int) lanai->pci->revision,
+ (unsigned long) lanai->base, lanai->pci->irq, atmdev->esi);
printk(KERN_NOTICE DEV_LABEL "(itf %d): LANAI%s, serialno=%u(0x%X), "
"board_rev=%d\n", lanai->number,
lanai->type==lanai2 ? "2" : "HB", (unsigned int) lanai->serialno,
@@ -2434,93 +2404,6 @@ static int lanai_open(struct atm_vcc *atmvcc)
return result;
}
-#if 0
-/* ioctl operations for card */
-/* NOTE: these are all DEBUGGING ONLY currently */
-static int lanai_ioctl(struct atm_dev *atmdev, unsigned int cmd, void __user *arg)
-{
- int result = 0;
- struct lanai_dev *lanai = (struct lanai_dev *) atmdev->dev_data;
- switch(cmd) {
- case 2106275:
- shutdown_atm_dev(atmdev);
- return 0;
- case 2200000: {
- unsigned long flags;
- spin_lock_irqsave(&lanai->servicelock, flags);
- run_service(lanai);
- spin_unlock_irqrestore(&lanai->servicelock, flags);
- return 0; }
- case 2200002:
- get_statistics(lanai);
- return 0;
- case 2200003: {
- unsigned int i;
- for (i = 0; i <= 0x5C ; i += 4) {
- if (i==0x48) /* Write-only butt reg */
- continue;
- printk(KERN_CRIT DEV_LABEL " 0x%02X: "
- "0x%08X\n", i,
- (unsigned int) readl(lanai->base + i));
- barrier(); mb();
- pcistatus_check(lanai, 0);
- barrier(); mb();
- }
- return 0; }
- case 2200004: {
- u8 b;
- u16 w;
- u32 dw;
- struct pci_dev *pci = lanai->pci;
- (void) pci_read_config_word(pci, PCI_VENDOR_ID, &w);
- DPRINTK("vendor = 0x%X\n", (unsigned int) w);
- (void) pci_read_config_word(pci, PCI_DEVICE_ID, &w);
- DPRINTK("device = 0x%X\n", (unsigned int) w);
- (void) pci_read_config_word(pci, PCI_COMMAND, &w);
- DPRINTK("command = 0x%X\n", (unsigned int) w);
- (void) pci_read_config_word(pci, PCI_STATUS, &w);
- DPRINTK("status = 0x%X\n", (unsigned int) w);
- (void) pci_read_config_dword(pci,
- PCI_CLASS_REVISION, &dw);
- DPRINTK("class/revision = 0x%X\n", (unsigned int) dw);
- (void) pci_read_config_byte(pci,
- PCI_CACHE_LINE_SIZE, &b);
- DPRINTK("cache line size = 0x%X\n", (unsigned int) b);
- (void) pci_read_config_byte(pci, PCI_LATENCY_TIMER, &b);
- DPRINTK("latency = %d (0x%X)\n",
- (int) b, (unsigned int) b);
- (void) pci_read_config_byte(pci, PCI_HEADER_TYPE, &b);
- DPRINTK("header type = 0x%X\n", (unsigned int) b);
- (void) pci_read_config_byte(pci, PCI_BIST, &b);
- DPRINTK("bist = 0x%X\n", (unsigned int) b);
- /* skipping a few here */
- (void) pci_read_config_byte(pci,
- PCI_INTERRUPT_LINE, &b);
- DPRINTK("pci_int_line = 0x%X\n", (unsigned int) b);
- (void) pci_read_config_byte(pci,
- PCI_INTERRUPT_PIN, &b);
- DPRINTK("pci_int_pin = 0x%X\n", (unsigned int) b);
- (void) pci_read_config_byte(pci, PCI_MIN_GNT, &b);
- DPRINTK("min_gnt = 0x%X\n", (unsigned int) b);
- (void) pci_read_config_byte(pci, PCI_MAX_LAT, &b);
- DPRINTK("max_lat = 0x%X\n", (unsigned int) b); }
- return 0;
-#ifdef USE_POWERDOWN
- case 2200005:
- DPRINTK("Coming out of powerdown\n");
- lanai->conf1 &= ~CONFIG1_POWERDOWN;
- conf1_write(lanai);
- return 0;
-#endif
- default:
- result = -ENOIOCTLCMD;
- }
- return result;
-}
-#else /* !0 */
-#define lanai_ioctl NULL
-#endif /* 0 */
-
static int lanai_send(struct atm_vcc *atmvcc, struct sk_buff *skb)
{
struct lanai_vcc *lvcc = (struct lanai_vcc *) atmvcc->dev_data;
@@ -2585,16 +2468,10 @@ static int lanai_proc_read(struct atm_dev *atmdev, loff_t *pos, char *page)
(unsigned int) lanai->magicno, lanai->num_vci);
if (left-- == 0)
return sprintf(page, "revision: board=%d, pci_if=%d\n",
- lanai->board_rev, (int) lanai->pci_revision);
+ lanai->board_rev, (int) lanai->pci->revision);
if (left-- == 0)
- return sprintf(page, "EEPROM ESI: "
- "%02X:%02X:%02X:%02X:%02X:%02X\n",
- lanai->eeprom[EEPROM_MAC + 0],
- lanai->eeprom[EEPROM_MAC + 1],
- lanai->eeprom[EEPROM_MAC + 2],
- lanai->eeprom[EEPROM_MAC + 3],
- lanai->eeprom[EEPROM_MAC + 4],
- lanai->eeprom[EEPROM_MAC + 5]);
+ return sprintf(page, "EEPROM ESI: %pM\n",
+ &lanai->eeprom[EEPROM_MAC]);
if (left-- == 0)
return sprintf(page, "status: SOOL=%d, LOCD=%d, LED=%d, "
"GPIN=%d\n", (lanai->status & STATUS_SOOL) ? 1 : 0,
@@ -2678,7 +2555,6 @@ static const struct atmdev_ops ops = {
.dev_close = lanai_dev_close,
.open = lanai_open,
.close = lanai_close,
- .ioctl = lanai_ioctl,
.getsockopt = NULL,
.setsockopt = NULL,
.send = lanai_send,
@@ -2690,21 +2566,21 @@ static const struct atmdev_ops ops = {
};
/* initialize one probed card */
-static int __devinit lanai_init_one(struct pci_dev *pci,
- const struct pci_device_id *ident)
+static int lanai_init_one(struct pci_dev *pci,
+ const struct pci_device_id *ident)
{
struct lanai_dev *lanai;
struct atm_dev *atmdev;
int result;
- lanai = (struct lanai_dev *) kmalloc(sizeof(*lanai), GFP_KERNEL);
+ lanai = kmalloc(sizeof(*lanai), GFP_KERNEL);
if (lanai == NULL) {
printk(KERN_ERR DEV_LABEL
": couldn't allocate dev_data structure!\n");
return -ENOMEM;
}
- atmdev = atm_dev_register(DEV_LABEL, &ops, -1, NULL);
+ atmdev = atm_dev_register(DEV_LABEL, &pci->dev, &ops, -1, NULL);
if (atmdev == NULL) {
printk(KERN_ERR DEV_LABEL
": couldn't register atm device!\n");
@@ -2726,14 +2602,8 @@ static int __devinit lanai_init_one(struct pci_dev *pci,
}
static struct pci_device_id lanai_pci_tbl[] = {
- {
- PCI_VENDOR_ID_EF, PCI_VENDOR_ID_EF_ATM_LANAI2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0
- },
- {
- PCI_VENDOR_ID_EF, PCI_VENDOR_ID_EF_ATM_LANAIHB,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0
- },
+ { PCI_VDEVICE(EF, PCI_DEVICE_ID_EF_ATM_LANAI2) },
+ { PCI_VDEVICE(EF, PCI_DEVICE_ID_EF_ATM_LANAIHB) },
{ 0, } /* terminal entry */
};
MODULE_DEVICE_TABLE(pci, lanai_pci_tbl);
@@ -2760,6 +2630,7 @@ static void __exit lanai_module_exit(void)
* gone, so there isn't much to do
*/
DPRINTK("cleanup_module()\n");
+ pci_unregister_driver(&lanai_driver);
}
module_init(lanai_module_init);
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-12-08 22:18:34 +0000