diff options
Diffstat (limited to 'drivers/ata/sata_mv.c')
| -rw-r--r-- | drivers/ata/sata_mv.c | 4159 |
1 files changed, 3104 insertions, 1055 deletions
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index c01496df4a9..391cfda1e83 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -1,9 +1,13 @@ /* * sata_mv.c - Marvell SATA support * + * Copyright 2008-2009: Marvell Corporation, all rights reserved. * Copyright 2005: EMC Corporation, all rights reserved. * Copyright 2005 Red Hat, Inc. All rights reserved. * + * Originally written by Brett Russ. + * Extensive overhaul and enhancement by Mark Lord <mlord@pobox.com>. + * * Please ALWAYS copy linux-ide@vger.kernel.org on emails. * * This program is free software; you can redistribute it and/or modify @@ -21,6 +25,30 @@ * */ +/* + * sata_mv TODO list: + * + * --> Develop a low-power-consumption strategy, and implement it. + * + * --> Add sysfs attributes for per-chip / per-HC IRQ coalescing thresholds. + * + * --> [Experiment, Marvell value added] Is it possible to use target + * mode to cross-connect two Linux boxes with Marvell cards? If so, + * creating LibATA target mode support would be very interesting. + * + * Target mode, for those without docs, is the ability to directly + * connect two SATA ports. + */ + +/* + * 80x1-B2 errata PCI#11: + * + * Users of the 6041/6081 Rev.B2 chips (current is C0) + * should be careful to insert those cards only onto PCI-X bus #0, + * and only in device slots 0..7, not higher. The chips may not + * work correctly otherwise (note: this is a pretty rare condition). + */ + #include <linux/kernel.h> #include <linux/module.h> #include <linux/pci.h> @@ -28,16 +56,45 @@ #include <linux/blkdev.h> #include <linux/delay.h> #include <linux/interrupt.h> -#include <linux/sched.h> +#include <linux/dmapool.h> #include <linux/dma-mapping.h> #include <linux/device.h> +#include <linux/clk.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/ata_platform.h> +#include <linux/mbus.h> +#include <linux/bitops.h> +#include <linux/gfp.h> +#include <linux/of.h> +#include <linux/of_irq.h> #include <scsi/scsi_host.h> #include <scsi/scsi_cmnd.h> +#include <scsi/scsi_device.h> #include <linux/libata.h> -#include <asm/io.h> #define DRV_NAME "sata_mv" -#define DRV_VERSION "0.7" +#define DRV_VERSION "1.28" + +/* + * module options + */ + +#ifdef CONFIG_PCI +static int msi; +module_param(msi, int, S_IRUGO); +MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)"); +#endif + +static int irq_coalescing_io_count; +module_param(irq_coalescing_io_count, int, S_IRUGO); +MODULE_PARM_DESC(irq_coalescing_io_count, + "IRQ coalescing I/O count threshold (0..255)"); + +static int irq_coalescing_usecs; +module_param(irq_coalescing_usecs, int, S_IRUGO); +MODULE_PARM_DESC(irq_coalescing_usecs, + "IRQ coalescing time threshold in usecs"); enum { /* BAR's are enumerated in terms of pci_resource_start() terms */ @@ -48,74 +105,102 @@ enum { MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */ MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */ + /* For use with both IRQ coalescing methods ("all ports" or "per-HC" */ + COAL_CLOCKS_PER_USEC = 150, /* for calculating COAL_TIMEs */ + MAX_COAL_TIME_THRESHOLD = ((1 << 24) - 1), /* internal clocks count */ + MAX_COAL_IO_COUNT = 255, /* completed I/O count */ + MV_PCI_REG_BASE = 0, - MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */ - MV_IRQ_COAL_CAUSE = (MV_IRQ_COAL_REG_BASE + 0x08), - MV_IRQ_COAL_CAUSE_LO = (MV_IRQ_COAL_REG_BASE + 0x88), - MV_IRQ_COAL_CAUSE_HI = (MV_IRQ_COAL_REG_BASE + 0x8c), - MV_IRQ_COAL_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xcc), - MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0), - - MV_SATAHC0_REG_BASE = 0x20000, - MV_FLASH_CTL = 0x1046c, - MV_GPIO_PORT_CTL = 0x104f0, - MV_RESET_CFG = 0x180d8, + + /* + * Per-chip ("all ports") interrupt coalescing feature. + * This is only for GEN_II / GEN_IIE hardware. + * + * Coalescing defers the interrupt until either the IO_THRESHOLD + * (count of completed I/Os) is met, or the TIME_THRESHOLD is met. + */ + COAL_REG_BASE = 0x18000, + IRQ_COAL_CAUSE = (COAL_REG_BASE + 0x08), + ALL_PORTS_COAL_IRQ = (1 << 4), /* all ports irq event */ + + IRQ_COAL_IO_THRESHOLD = (COAL_REG_BASE + 0xcc), + IRQ_COAL_TIME_THRESHOLD = (COAL_REG_BASE + 0xd0), + + /* + * Registers for the (unused here) transaction coalescing feature: + */ + TRAN_COAL_CAUSE_LO = (COAL_REG_BASE + 0x88), + TRAN_COAL_CAUSE_HI = (COAL_REG_BASE + 0x8c), + + SATAHC0_REG_BASE = 0x20000, + FLASH_CTL = 0x1046c, + GPIO_PORT_CTL = 0x104f0, + RESET_CFG = 0x180d8, MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ, MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ, MV_SATAHC_ARBTR_REG_SZ = MV_MINOR_REG_AREA_SZ, /* arbiter */ MV_PORT_REG_SZ = MV_MINOR_REG_AREA_SZ, - MV_USE_Q_DEPTH = ATA_DEF_QUEUE, - MV_MAX_Q_DEPTH = 32, MV_MAX_Q_DEPTH_MASK = MV_MAX_Q_DEPTH - 1, /* CRQB needs alignment on a 1KB boundary. Size == 1KB * CRPB needs alignment on a 256B boundary. Size == 256B - * SG count of 176 leads to MV_PORT_PRIV_DMA_SZ == 4KB * ePRD (SG) entries need alignment on a 16B boundary. Size == 16B */ MV_CRQB_Q_SZ = (32 * MV_MAX_Q_DEPTH), MV_CRPB_Q_SZ = (8 * MV_MAX_Q_DEPTH), - MV_MAX_SG_CT = 176, + MV_MAX_SG_CT = 256, MV_SG_TBL_SZ = (16 * MV_MAX_SG_CT), - MV_PORT_PRIV_DMA_SZ = (MV_CRQB_Q_SZ + MV_CRPB_Q_SZ + MV_SG_TBL_SZ), - MV_PORTS_PER_HC = 4, - /* == (port / MV_PORTS_PER_HC) to determine HC from 0-7 port */ + /* Determine hc from 0-7 port: hc = port >> MV_PORT_HC_SHIFT */ MV_PORT_HC_SHIFT = 2, - /* == (port % MV_PORTS_PER_HC) to determine hard port from 0-7 port */ - MV_PORT_MASK = 3, + MV_PORTS_PER_HC = (1 << MV_PORT_HC_SHIFT), /* 4 */ + /* Determine hc port from 0-7 port: hardport = port & MV_PORT_MASK */ + MV_PORT_MASK = (MV_PORTS_PER_HC - 1), /* 3 */ /* Host Flags */ MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */ - MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */ - MV_COMMON_FLAGS = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | - ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO | - ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING), - MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE, + + MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_PIO_POLLING, + + MV_GEN_I_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NO_ATAPI, + + MV_GEN_II_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NCQ | + ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA, + + MV_GEN_IIE_FLAGS = MV_GEN_II_FLAGS | ATA_FLAG_AN, CRQB_FLAG_READ = (1 << 0), CRQB_TAG_SHIFT = 1, + CRQB_IOID_SHIFT = 6, /* CRQB Gen-II/IIE IO Id shift */ + CRQB_PMP_SHIFT = 12, /* CRQB Gen-II/IIE PMP shift */ + CRQB_HOSTQ_SHIFT = 17, /* CRQB Gen-II/IIE HostQueTag shift */ CRQB_CMD_ADDR_SHIFT = 8, CRQB_CMD_CS = (0x2 << 11), CRQB_CMD_LAST = (1 << 15), CRPB_FLAG_STATUS_SHIFT = 8, + CRPB_IOID_SHIFT_6 = 5, /* CRPB Gen-II IO Id shift */ + CRPB_IOID_SHIFT_7 = 7, /* CRPB Gen-IIE IO Id shift */ EPRD_FLAG_END_OF_TBL = (1 << 31), /* PCI interface registers */ - PCI_COMMAND_OFS = 0xc00, + MV_PCI_COMMAND = 0xc00, + MV_PCI_COMMAND_MWRCOM = (1 << 4), /* PCI Master Write Combining */ + MV_PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */ - PCI_MAIN_CMD_STS_OFS = 0xd30, + PCI_MAIN_CMD_STS = 0xd30, STOP_PCI_MASTER = (1 << 2), PCI_MASTER_EMPTY = (1 << 3), GLOB_SFT_RST = (1 << 4), MV_PCI_MODE = 0xd00, + MV_PCI_MODE_MASK = 0x30, + MV_PCI_EXP_ROM_BAR_CTL = 0xd2c, MV_PCI_DISC_TIMER = 0xd04, MV_PCI_MSI_TRIGGER = 0xc38, @@ -126,137 +211,259 @@ enum { MV_PCI_ERR_ATTRIBUTE = 0x1d48, MV_PCI_ERR_COMMAND = 0x1d50, - PCI_IRQ_CAUSE_OFS = 0x1d58, - PCI_IRQ_MASK_OFS = 0x1d5c, + PCI_IRQ_CAUSE = 0x1d58, + PCI_IRQ_MASK = 0x1d5c, PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */ - HC_MAIN_IRQ_CAUSE_OFS = 0x1d60, - HC_MAIN_IRQ_MASK_OFS = 0x1d64, - PORT0_ERR = (1 << 0), /* shift by port # */ - PORT0_DONE = (1 << 1), /* shift by port # */ + PCIE_IRQ_CAUSE = 0x1900, + PCIE_IRQ_MASK = 0x1910, + PCIE_UNMASK_ALL_IRQS = 0x40a, /* assorted bits */ + + /* Host Controller Main Interrupt Cause/Mask registers (1 per-chip) */ + PCI_HC_MAIN_IRQ_CAUSE = 0x1d60, + PCI_HC_MAIN_IRQ_MASK = 0x1d64, + SOC_HC_MAIN_IRQ_CAUSE = 0x20020, + SOC_HC_MAIN_IRQ_MASK = 0x20024, + ERR_IRQ = (1 << 0), /* shift by (2 * port #) */ + DONE_IRQ = (1 << 1), /* shift by (2 * port #) */ HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */ HC_SHIFT = 9, /* bits 9-17 = HC1's ports */ + DONE_IRQ_0_3 = 0x000000aa, /* DONE_IRQ ports 0,1,2,3 */ + DONE_IRQ_4_7 = (DONE_IRQ_0_3 << HC_SHIFT), /* 4,5,6,7 */ PCI_ERR = (1 << 18), - TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */ - TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */ - PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */ + TRAN_COAL_LO_DONE = (1 << 19), /* transaction coalescing */ + TRAN_COAL_HI_DONE = (1 << 20), /* transaction coalescing */ + PORTS_0_3_COAL_DONE = (1 << 8), /* HC0 IRQ coalescing */ + PORTS_4_7_COAL_DONE = (1 << 17), /* HC1 IRQ coalescing */ + ALL_PORTS_COAL_DONE = (1 << 21), /* GEN_II(E) IRQ coalescing */ GPIO_INT = (1 << 22), SELF_INT = (1 << 23), TWSI_INT = (1 << 24), HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */ - HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE | - PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT | - HC_MAIN_RSVD), + HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */ + HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */ /* SATAHC registers */ - HC_CFG_OFS = 0, + HC_CFG = 0x00, - HC_IRQ_CAUSE_OFS = 0x14, - CRPB_DMA_DONE = (1 << 0), /* shift by port # */ - HC_IRQ_COAL = (1 << 4), /* IRQ coalescing */ + HC_IRQ_CAUSE = 0x14, + DMA_IRQ = (1 << 0), /* shift by port # */ + HC_COAL_IRQ = (1 << 4), /* IRQ coalescing */ DEV_IRQ = (1 << 8), /* shift by port # */ + /* + * Per-HC (Host-Controller) interrupt coalescing feature. + * This is present on all chip generations. + * + * Coalescing defers the interrupt until either the IO_THRESHOLD + * (count of completed I/Os) is met, or the TIME_THRESHOLD is met. + */ + HC_IRQ_COAL_IO_THRESHOLD = 0x000c, + HC_IRQ_COAL_TIME_THRESHOLD = 0x0010, + + SOC_LED_CTRL = 0x2c, + SOC_LED_CTRL_BLINK = (1 << 0), /* Active LED blink */ + SOC_LED_CTRL_ACT_PRESENCE = (1 << 2), /* Multiplex dev presence */ + /* with dev activity LED */ + /* Shadow block registers */ - SHD_BLK_OFS = 0x100, - SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */ + SHD_BLK = 0x100, + SHD_CTL_AST = 0x20, /* ofs from SHD_BLK */ /* SATA registers */ - SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */ - SATA_ACTIVE_OFS = 0x350, - PHY_MODE3 = 0x310, - PHY_MODE4 = 0x314, + SATA_STATUS = 0x300, /* ctrl, err regs follow status */ + SATA_ACTIVE = 0x350, + FIS_IRQ_CAUSE = 0x364, + FIS_IRQ_CAUSE_AN = (1 << 9), /* async notification */ + + LTMODE = 0x30c, /* requires read-after-write */ + LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */ + PHY_MODE2 = 0x330, + PHY_MODE3 = 0x310, + + PHY_MODE4 = 0x314, /* requires read-after-write */ + PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */ + PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */ + PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */ + PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */ + + SATA_IFCTL = 0x344, + SATA_TESTCTL = 0x348, + SATA_IFSTAT = 0x34c, + VENDOR_UNIQUE_FIS = 0x35c, + + FISCFG = 0x360, + FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */ + FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */ + + PHY_MODE9_GEN2 = 0x398, + PHY_MODE9_GEN1 = 0x39c, + PHYCFG_OFS = 0x3a0, /* only in 65n devices */ + MV5_PHY_MODE = 0x74, - MV5_LT_MODE = 0x30, + MV5_LTMODE = 0x30, MV5_PHY_CTL = 0x0C, - SATA_INTERFACE_CTL = 0x050, + SATA_IFCFG = 0x050, + LP_PHY_CTL = 0x058, MV_M2_PREAMP_MASK = 0x7e0, /* Port registers */ - EDMA_CFG_OFS = 0, - EDMA_CFG_Q_DEPTH = 0, /* queueing disabled */ - EDMA_CFG_NCQ = (1 << 5), - EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */ - EDMA_CFG_RD_BRST_EXT = (1 << 11), /* read burst 512B */ - EDMA_CFG_WR_BUFF_LEN = (1 << 13), /* write buffer 512B */ - - EDMA_ERR_IRQ_CAUSE_OFS = 0x8, - EDMA_ERR_IRQ_MASK_OFS = 0xc, - EDMA_ERR_D_PAR = (1 << 0), - EDMA_ERR_PRD_PAR = (1 << 1), - EDMA_ERR_DEV = (1 << 2), - EDMA_ERR_DEV_DCON = (1 << 3), - EDMA_ERR_DEV_CON = (1 << 4), - EDMA_ERR_SERR = (1 << 5), - EDMA_ERR_SELF_DIS = (1 << 7), - EDMA_ERR_BIST_ASYNC = (1 << 8), - EDMA_ERR_CRBQ_PAR = (1 << 9), - EDMA_ERR_CRPB_PAR = (1 << 10), - EDMA_ERR_INTRL_PAR = (1 << 11), - EDMA_ERR_IORDY = (1 << 12), - EDMA_ERR_LNK_CTRL_RX = (0xf << 13), - EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15), - EDMA_ERR_LNK_DATA_RX = (0xf << 17), - EDMA_ERR_LNK_CTRL_TX = (0x1f << 21), - EDMA_ERR_LNK_DATA_TX = (0x1f << 26), - EDMA_ERR_TRANS_PROTO = (1 << 31), - EDMA_ERR_FATAL = (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | - EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR | - EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR | - EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 | - EDMA_ERR_LNK_DATA_RX | - EDMA_ERR_LNK_DATA_TX | - EDMA_ERR_TRANS_PROTO), - - EDMA_REQ_Q_BASE_HI_OFS = 0x10, - EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */ - - EDMA_REQ_Q_OUT_PTR_OFS = 0x18, + EDMA_CFG = 0, + EDMA_CFG_Q_DEPTH = 0x1f, /* max device queue depth */ + EDMA_CFG_NCQ = (1 << 5), /* for R/W FPDMA queued */ + EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */ + EDMA_CFG_RD_BRST_EXT = (1 << 11), /* read burst 512B */ + EDMA_CFG_WR_BUFF_LEN = (1 << 13), /* write buffer 512B */ + EDMA_CFG_EDMA_FBS = (1 << 16), /* EDMA FIS-Based Switching */ + EDMA_CFG_FBS = (1 << 26), /* FIS-Based Switching */ + + EDMA_ERR_IRQ_CAUSE = 0x8, + EDMA_ERR_IRQ_MASK = 0xc, + EDMA_ERR_D_PAR = (1 << 0), /* UDMA data parity err */ + EDMA_ERR_PRD_PAR = (1 << 1), /* UDMA PRD parity err */ + EDMA_ERR_DEV = (1 << 2), /* device error */ + EDMA_ERR_DEV_DCON = (1 << 3), /* device disconnect */ + EDMA_ERR_DEV_CON = (1 << 4), /* device connected */ + EDMA_ERR_SERR = (1 << 5), /* SError bits [WBDST] raised */ + EDMA_ERR_SELF_DIS = (1 << 7), /* Gen II/IIE self-disable */ + EDMA_ERR_SELF_DIS_5 = (1 << 8), /* Gen I self-disable */ + EDMA_ERR_BIST_ASYNC = (1 << 8), /* BIST FIS or Async Notify */ + EDMA_ERR_TRANS_IRQ_7 = (1 << 8), /* Gen IIE transprt layer irq */ + EDMA_ERR_CRQB_PAR = (1 << 9), /* CRQB parity error */ + EDMA_ERR_CRPB_PAR = (1 << 10), /* CRPB parity error */ + EDMA_ERR_INTRL_PAR = (1 << 11), /* internal parity error */ + EDMA_ERR_IORDY = (1 << 12), /* IORdy timeout */ + + EDMA_ERR_LNK_CTRL_RX = (0xf << 13), /* link ctrl rx error */ + EDMA_ERR_LNK_CTRL_RX_0 = (1 << 13), /* transient: CRC err */ + EDMA_ERR_LNK_CTRL_RX_1 = (1 << 14), /* transient: FIFO err */ + EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15), /* fatal: caught SYNC */ + EDMA_ERR_LNK_CTRL_RX_3 = (1 << 16), /* transient: FIS rx err */ + + EDMA_ERR_LNK_DATA_RX = (0xf << 17), /* link data rx error */ + + EDMA_ERR_LNK_CTRL_TX = (0x1f << 21), /* link ctrl tx error */ + EDMA_ERR_LNK_CTRL_TX_0 = (1 << 21), /* transient: CRC err */ + EDMA_ERR_LNK_CTRL_TX_1 = (1 << 22), /* transient: FIFO err */ + EDMA_ERR_LNK_CTRL_TX_2 = (1 << 23), /* transient: caught SYNC */ + EDMA_ERR_LNK_CTRL_TX_3 = (1 << 24), /* transient: caught DMAT */ + EDMA_ERR_LNK_CTRL_TX_4 = (1 << 25), /* transient: FIS collision */ + + EDMA_ERR_LNK_DATA_TX = (0x1f << 26), /* link data tx error */ + + EDMA_ERR_TRANS_PROTO = (1 << 31), /* transport protocol error */ + EDMA_ERR_OVERRUN_5 = (1 << 5), + EDMA_ERR_UNDERRUN_5 = (1 << 6), + + EDMA_ERR_IRQ_TRANSIENT = EDMA_ERR_LNK_CTRL_RX_0 | + EDMA_ERR_LNK_CTRL_RX_1 | + EDMA_ERR_LNK_CTRL_RX_3 | + EDMA_ERR_LNK_CTRL_TX, + + EDMA_EH_FREEZE = EDMA_ERR_D_PAR | + EDMA_ERR_PRD_PAR | + EDMA_ERR_DEV_DCON | + EDMA_ERR_DEV_CON | + EDMA_ERR_SERR | + EDMA_ERR_SELF_DIS | + EDMA_ERR_CRQB_PAR | + EDMA_ERR_CRPB_PAR | + EDMA_ERR_INTRL_PAR | + EDMA_ERR_IORDY | + EDMA_ERR_LNK_CTRL_RX_2 | + EDMA_ERR_LNK_DATA_RX | + EDMA_ERR_LNK_DATA_TX | + EDMA_ERR_TRANS_PROTO, + + EDMA_EH_FREEZE_5 = EDMA_ERR_D_PAR | + EDMA_ERR_PRD_PAR | + EDMA_ERR_DEV_DCON | + EDMA_ERR_DEV_CON | + EDMA_ERR_OVERRUN_5 | + EDMA_ERR_UNDERRUN_5 | + EDMA_ERR_SELF_DIS_5 | + EDMA_ERR_CRQB_PAR | + EDMA_ERR_CRPB_PAR | + EDMA_ERR_INTRL_PAR | + EDMA_ERR_IORDY, + + EDMA_REQ_Q_BASE_HI = 0x10, + EDMA_REQ_Q_IN_PTR = 0x14, /* also contains BASE_LO */ + + EDMA_REQ_Q_OUT_PTR = 0x18, EDMA_REQ_Q_PTR_SHIFT = 5, - EDMA_RSP_Q_BASE_HI_OFS = 0x1c, - EDMA_RSP_Q_IN_PTR_OFS = 0x20, - EDMA_RSP_Q_OUT_PTR_OFS = 0x24, /* also contains BASE_LO */ + EDMA_RSP_Q_BASE_HI = 0x1c, + EDMA_RSP_Q_IN_PTR = 0x20, + EDMA_RSP_Q_OUT_PTR = 0x24, /* also contains BASE_LO */ EDMA_RSP_Q_PTR_SHIFT = 3, - EDMA_CMD_OFS = 0x28, - EDMA_EN = (1 << 0), - EDMA_DS = (1 << 1), - ATA_RST = (1 << 2), + EDMA_CMD = 0x28, /* EDMA command register */ + EDMA_EN = (1 << 0), /* enable EDMA */ + EDMA_DS = (1 << 1), /* disable EDMA; self-negated */ + EDMA_RESET = (1 << 2), /* reset eng/trans/link/phy */ + + EDMA_STATUS = 0x30, /* EDMA engine status */ + EDMA_STATUS_CACHE_EMPTY = (1 << 6), /* GenIIe command cache empty */ + EDMA_STATUS_IDLE = (1 << 7), /* GenIIe EDMA enabled/idle */ EDMA_IORDY_TMOUT = 0x34, EDMA_ARB_CFG = 0x38, + EDMA_HALTCOND = 0x60, /* GenIIe halt conditions */ + EDMA_UNKNOWN_RSVD = 0x6C, /* GenIIe unknown/reserved */ + + BMDMA_CMD = 0x224, /* bmdma command register */ + BMDMA_STATUS = 0x228, /* bmdma status register */ + BMDMA_PRD_LOW = 0x22c, /* bmdma PRD addr 31:0 */ + BMDMA_PRD_HIGH = 0x230, /* bmdma PRD addr 63:32 */ + /* Host private flags (hp_flags) */ MV_HP_FLAG_MSI = (1 << 0), MV_HP_ERRATA_50XXB0 = (1 << 1), MV_HP_ERRATA_50XXB2 = (1 << 2), MV_HP_ERRATA_60X1B2 = (1 << 3), MV_HP_ERRATA_60X1C0 = (1 << 4), - MV_HP_ERRATA_XX42A0 = (1 << 5), - MV_HP_50XX = (1 << 6), - MV_HP_GEN_IIE = (1 << 7), + MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */ + MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */ + MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */ + MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */ + MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */ + MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */ + MV_HP_QUIRK_LED_BLINK_EN = (1 << 12), /* is led blinking enabled? */ + MV_HP_FIX_LP_PHY_CTL = (1 << 13), /* fix speed in LP_PHY_CTL ? */ /* Port private flags (pp_flags) */ - MV_PP_FLAG_EDMA_EN = (1 << 0), - MV_PP_FLAG_EDMA_DS_ACT = (1 << 1), + MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */ + MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */ + MV_PP_FLAG_FBS_EN = (1 << 2), /* is EDMA set up for FBS? */ + MV_PP_FLAG_DELAYED_EH = (1 << 3), /* delayed dev err handling */ + MV_PP_FLAG_FAKE_ATA_BUSY = (1 << 4), /* ignore initial ATA_DRDY */ }; -#define IS_50XX(hpriv) ((hpriv)->hp_flags & MV_HP_50XX) -#define IS_60XX(hpriv) (((hpriv)->hp_flags & MV_HP_50XX) == 0) -#define IS_GEN_I(hpriv) IS_50XX(hpriv) -#define IS_GEN_II(hpriv) IS_60XX(hpriv) +#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I) +#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II) #define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE) +#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE) +#define IS_SOC(hpriv) ((hpriv)->hp_flags & MV_HP_FLAG_SOC) + +#define WINDOW_CTRL(i) (0x20030 + ((i) << 4)) +#define WINDOW_BASE(i) (0x20034 + ((i) << 4)) enum { - /* Our DMA boundary is determined by an ePRD being unable to handle - * anything larger than 64KB + /* DMA boundary 0xffff is required by the s/g splitting + * we need on /length/ in mv_fill-sg(). */ MV_DMA_BOUNDARY = 0xffffU, + /* mask of register bits containing lower 32 bits + * of EDMA request queue DMA address + */ EDMA_REQ_Q_BASE_LO_MASK = 0xfffffc00U, + /* ditto, for response queue */ EDMA_RSP_Q_BASE_LO_MASK = 0xffffff00U, }; @@ -268,6 +475,7 @@ enum chip_type { chip_608x, chip_6042, chip_7042, + chip_soc, }; /* Command ReQuest Block: 32B */ @@ -301,14 +509,32 @@ struct mv_sg { __le32 reserved; }; +/* + * We keep a local cache of a few frequently accessed port + * registers here, to avoid having to read them (very slow) + * when switching between EDMA and non-EDMA modes. + */ +struct mv_cached_regs { + u32 fiscfg; + u32 ltmode; + u32 haltcond; + u32 unknown_rsvd; +}; + struct mv_port_priv { struct mv_crqb *crqb; dma_addr_t crqb_dma; struct mv_crpb *crpb; dma_addr_t crpb_dma; - struct mv_sg *sg_tbl; - dma_addr_t sg_tbl_dma; + struct mv_sg *sg_tbl[MV_MAX_Q_DEPTH]; + dma_addr_t sg_tbl_dma[MV_MAX_Q_DEPTH]; + + unsigned int req_idx; + unsigned int resp_idx; + u32 pp_flags; + struct mv_cached_regs cached; + unsigned int delayed_eh_pmp_map; }; struct mv_port_signal { @@ -316,7 +542,45 @@ struct mv_port_signal { u32 pre; }; -struct mv_host_priv; +struct mv_host_priv { + u32 hp_flags; + unsigned int board_idx; + u32 main_irq_mask; + struct mv_port_signal signal[8]; + const struct mv_hw_ops *ops; + int n_ports; + void __iomem *base; + void __iomem *main_irq_cause_addr; + void __iomem *main_irq_mask_addr; + u32 irq_cause_offset; + u32 irq_mask_offset; + u32 unmask_all_irqs; + + /* + * Needed on some devices that require their clocks to be enabled. + * These are optional: if the platform device does not have any + * clocks, they won't be used. Also, if the underlying hardware + * does not support the common clock framework (CONFIG_HAVE_CLK=n), + * all the clock operations become no-ops (see clk.h). + */ + struct clk *clk; + struct clk **port_clks; + /* + * Some devices have a SATA PHY which can be enabled/disabled + * in order to save power. These are optional: if the platform + * devices does not have any phy, they won't be used. + */ + struct phy **port_phys; + /* + * These consistent DMA memory pools give us guaranteed + * alignment for hardware-accessed data structures, + * and less memory waste in accomplishing the alignment. + */ + struct dma_pool *crqb_pool; + struct dma_pool *crpb_pool; + struct dma_pool *sg_tbl_pool; +}; + struct mv_hw_ops { void (*phy_errata)(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port); @@ -326,32 +590,24 @@ struct mv_hw_ops { int (*reset_hc)(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int n_hc); void (*reset_flash)(struct mv_host_priv *hpriv, void __iomem *mmio); - void (*reset_bus)(struct pci_dev *pdev, void __iomem *mmio); -}; - -struct mv_host_priv { - u32 hp_flags; - struct mv_port_signal signal[8]; - const struct mv_hw_ops *ops; + void (*reset_bus)(struct ata_host *host, void __iomem *mmio); }; -static void mv_irq_clear(struct ata_port *ap); -static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in); -static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); -static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in); -static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); -static void mv_phy_reset(struct ata_port *ap); -static void __mv_phy_reset(struct ata_port *ap, int can_sleep); -static void mv_host_stop(struct ata_host *host); +static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val); +static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val); +static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val); +static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val); static int mv_port_start(struct ata_port *ap); static void mv_port_stop(struct ata_port *ap); +static int mv_qc_defer(struct ata_queued_cmd *qc); static void mv_qc_prep(struct ata_queued_cmd *qc); static void mv_qc_prep_iie(struct ata_queued_cmd *qc); static unsigned int mv_qc_issue(struct ata_queued_cmd *qc); -static irqreturn_t mv_interrupt(int irq, void *dev_instance, - struct pt_regs *regs); -static void mv_eng_timeout(struct ata_port *ap); -static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); +static int mv_hardreset(struct ata_link *link, unsigned int *class, + unsigned long deadline); +static void mv_eh_freeze(struct ata_port *ap); +static void mv_eh_thaw(struct ata_port *ap); +static void mv6_dev_config(struct ata_device *dev); static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port); @@ -361,7 +617,7 @@ static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx, static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int n_hc); static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio); -static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio); +static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio); static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port); @@ -371,188 +627,199 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int n_hc); static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio); -static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio); -static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio, +static void mv_soc_enable_leds(struct mv_host_priv *hpriv, + void __iomem *mmio); +static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio); +static int mv_soc_reset_hc(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int n_hc); +static void mv_soc_reset_flash(struct mv_host_priv *hpriv, + void __iomem *mmio); +static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio); +static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int port); +static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio); +static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port_no); -static void mv_stop_and_reset(struct ata_port *ap); - -static struct scsi_host_template mv_sht = { - .module = THIS_MODULE, - .name = DRV_NAME, - .ioctl = ata_scsi_ioctl, - .queuecommand = ata_scsi_queuecmd, - .can_queue = MV_USE_Q_DEPTH, - .this_id = ATA_SHT_THIS_ID, +static int mv_stop_edma(struct ata_port *ap); +static int mv_stop_edma_engine(void __iomem *port_mmio); +static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma); + +static void mv_pmp_select(struct ata_port *ap, int pmp); +static int mv_pmp_hardreset(struct ata_link *link, unsigned int *class, + unsigned long deadline); +static int mv_softreset(struct ata_link *link, unsigned int *class, + unsigned long deadline); +static void mv_pmp_error_handler(struct ata_port *ap); +static void mv_process_crpb_entries(struct ata_port *ap, + struct mv_port_priv *pp); + +static void mv_sff_irq_clear(struct ata_port *ap); +static int mv_check_atapi_dma(struct ata_queued_cmd *qc); +static void mv_bmdma_setup(struct ata_queued_cmd *qc); +static void mv_bmdma_start(struct ata_queued_cmd *qc); +static void mv_bmdma_stop(struct ata_queued_cmd *qc); +static u8 mv_bmdma_status(struct ata_port *ap); +static u8 mv_sff_check_status(struct ata_port *ap); + +/* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below + * because we have to allow room for worst case splitting of + * PRDs for 64K boundaries in mv_fill_sg(). + */ +#ifdef CONFIG_PCI +static struct scsi_host_template mv5_sht = { + ATA_BASE_SHT(DRV_NAME), + .sg_tablesize = MV_MAX_SG_CT / 2, + .dma_boundary = MV_DMA_BOUNDARY, +}; +#endif +static struct scsi_host_template mv6_sht = { + ATA_NCQ_SHT(DRV_NAME), + .can_queue = MV_MAX_Q_DEPTH - 1, .sg_tablesize = MV_MAX_SG_CT / 2, - .cmd_per_lun = ATA_SHT_CMD_PER_LUN, - .emulated = ATA_SHT_EMULATED, - .use_clustering = ATA_SHT_USE_CLUSTERING, - .proc_name = DRV_NAME, .dma_boundary = MV_DMA_BOUNDARY, - .slave_configure = ata_scsi_slave_config, - .slave_destroy = ata_scsi_slave_destroy, - .bios_param = ata_std_bios_param, }; -static const struct ata_port_operations mv5_ops = { - .port_disable = ata_port_disable, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, +static struct ata_port_operations mv5_ops = { + .inherits = &ata_sff_port_ops, - .phy_reset = mv_phy_reset, + .lost_interrupt = ATA_OP_NULL, + .qc_defer = mv_qc_defer, .qc_prep = mv_qc_prep, .qc_issue = mv_qc_issue, - .data_xfer = ata_mmio_data_xfer, - .eng_timeout = mv_eng_timeout, - - .irq_handler = mv_interrupt, - .irq_clear = mv_irq_clear, + .freeze = mv_eh_freeze, + .thaw = mv_eh_thaw, + .hardreset = mv_hardreset, .scr_read = mv5_scr_read, .scr_write = mv5_scr_write, .port_start = mv_port_start, .port_stop = mv_port_stop, - .host_stop = mv_host_stop, }; -static const struct ata_port_operations mv6_ops = { - .port_disable = ata_port_disable, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, +static struct ata_port_operations mv6_ops = { + .inherits = &ata_bmdma_port_ops, - .phy_reset = mv_phy_reset, + .lost_interrupt = ATA_OP_NULL, + .qc_defer = mv_qc_defer, .qc_prep = mv_qc_prep, .qc_issue = mv_qc_issue, - .data_xfer = ata_mmio_data_xfer, - .eng_timeout = mv_eng_timeout, + .dev_config = mv6_dev_config, - .irq_handler = mv_interrupt, - .irq_clear = mv_irq_clear, + .freeze = mv_eh_freeze, + .thaw = mv_eh_thaw, + .hardreset = mv_hardreset, + .softreset = mv_softreset, + .pmp_hardreset = mv_pmp_hardreset, + .pmp_softreset = mv_softreset, + .error_handler = mv_pmp_error_handler, .scr_read = mv_scr_read, .scr_write = mv_scr_write, + .sff_check_status = mv_sff_check_status, + .sff_irq_clear = mv_sff_irq_clear, + .check_atapi_dma = mv_check_atapi_dma, + .bmdma_setup = mv_bmdma_setup, + .bmdma_start = mv_bmdma_start, + .bmdma_stop = mv_bmdma_stop, + .bmdma_status = mv_bmdma_status, + .port_start = mv_port_start, .port_stop = mv_port_stop, - .host_stop = mv_host_stop, }; -static const struct ata_port_operations mv_iie_ops = { - .port_disable = ata_port_disable, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, - - .phy_reset = mv_phy_reset, - +static struct ata_port_operations mv_iie_ops = { + .inherits = &mv6_ops, + .dev_config = ATA_OP_NULL, .qc_prep = mv_qc_prep_iie, - .qc_issue = mv_qc_issue, - .data_xfer = ata_mmio_data_xfer, - - .eng_timeout = mv_eng_timeout, - - .irq_handler = mv_interrupt, - .irq_clear = mv_irq_clear, - - .scr_read = mv_scr_read, - .scr_write = mv_scr_write, - - .port_start = mv_port_start, - .port_stop = mv_port_stop, - .host_stop = mv_host_stop, }; static const struct ata_port_info mv_port_info[] = { { /* chip_504x */ - .sht = &mv_sht, - .flags = MV_COMMON_FLAGS, - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_I_FLAGS, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv5_ops, }, { /* chip_508x */ - .sht = &mv_sht, - .flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC), - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv5_ops, }, { /* chip_5080 */ - .sht = &mv_sht, - .flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC), - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv5_ops, }, { /* chip_604x */ - .sht = &mv_sht, - .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS), - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_II_FLAGS, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv6_ops, }, { /* chip_608x */ - .sht = &mv_sht, - .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS | - MV_FLAG_DUAL_HC), - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_II_FLAGS | MV_FLAG_DUAL_HC, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv6_ops, }, { /* chip_6042 */ - .sht = &mv_sht, - .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS), - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_IIE_FLAGS, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv_iie_ops, }, { /* chip_7042 */ - .sht = &mv_sht, - .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS | - MV_FLAG_DUAL_HC), - .pio_mask = 0x1f, /* pio0-4 */ - .udma_mask = 0x7f, /* udma0-6 */ + .flags = MV_GEN_IIE_FLAGS, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, + .port_ops = &mv_iie_ops, + }, + { /* chip_soc */ + .flags = MV_GEN_IIE_FLAGS, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, .port_ops = &mv_iie_ops, }, }; static const struct pci_device_id mv_pci_tbl[] = { - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5040), 0, 0, chip_504x}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5041), 0, 0, chip_504x}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5080), 0, 0, chip_5080}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5081), 0, 0, chip_508x}, - - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6040), 0, 0, chip_604x}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6041), 0, 0, chip_604x}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6042), 0, 0, chip_6042}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6080), 0, 0, chip_608x}, - {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6081), 0, 0, chip_608x}, - - {PCI_DEVICE(PCI_VENDOR_ID_ADAPTEC2, 0x0241), 0, 0, chip_604x}, - {} /* terminate list */ -}; - -static struct pci_driver mv_pci_driver = { - .name = DRV_NAME, - .id_table = mv_pci_tbl, - .probe = mv_init_one, - .remove = ata_pci_remove_one, + { PCI_VDEVICE(MARVELL, 0x5040), chip_504x }, + { PCI_VDEVICE(MARVELL, 0x5041), chip_504x }, + { PCI_VDEVICE(MARVELL, 0x5080), chip_5080 }, + { PCI_VDEVICE(MARVELL, 0x5081), chip_508x }, + /* RocketRAID 1720/174x have different identifiers */ + { PCI_VDEVICE(TTI, 0x1720), chip_6042 }, + { PCI_VDEVICE(TTI, 0x1740), chip_6042 }, + { PCI_VDEVICE(TTI, 0x1742), chip_6042 }, + + { PCI_VDEVICE(MARVELL, 0x6040), chip_604x }, + { PCI_VDEVICE(MARVELL, 0x6041), chip_604x }, + { PCI_VDEVICE(MARVELL, 0x6042), chip_6042 }, + { PCI_VDEVICE(MARVELL, 0x6080), chip_608x }, + { PCI_VDEVICE(MARVELL, 0x6081), chip_608x }, + + { PCI_VDEVICE(ADAPTEC2, 0x0241), chip_604x }, + + /* Adaptec 1430SA */ + { PCI_VDEVICE(ADAPTEC2, 0x0243), chip_7042 }, + + /* Marvell 7042 support */ + { PCI_VDEVICE(MARVELL, 0x7042), chip_7042 }, + + /* Highpoint RocketRAID PCIe series */ + { PCI_VDEVICE(TTI, 0x2300), chip_7042 }, + { PCI_VDEVICE(TTI, 0x2310), chip_7042 }, + + { } /* terminate list */ }; static const struct mv_hw_ops mv5xxx_ops = { @@ -573,11 +840,22 @@ static const struct mv_hw_ops mv6xxx_ops = { .reset_bus = mv_reset_pci_bus, }; -/* - * module options - */ -static int msi; /* Use PCI msi; either zero (off, default) or non-zero */ +static const struct mv_hw_ops mv_soc_ops = { + .phy_errata = mv6_phy_errata, + .enable_leds = mv_soc_enable_leds, + .read_preamp = mv_soc_read_preamp, + .reset_hc = mv_soc_reset_hc, + .reset_flash = mv_soc_reset_flash, + .reset_bus = mv_soc_reset_bus, +}; +static const struct mv_hw_ops mv_soc_65n_ops = { + .phy_errata = mv_soc_65n_phy_errata, + .enable_leds = mv_soc_enable_leds, + .reset_hc = mv_soc_reset_hc, + .reset_flash = mv_soc_reset_flash, + .reset_bus = mv_soc_reset_bus, +}; /* * Functions @@ -589,11 +867,6 @@ static inline void writelfl(unsigned long data, void __iomem *addr) (void) readl(addr); /* flush to avoid PCI posted write */ } -static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc) -{ - return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ)); -} - static inline unsigned int mv_hc_from_port(unsigned int port) { return port >> MV_PORT_HC_SHIFT; @@ -604,6 +877,29 @@ static inline unsigned int mv_hardport_from_port(unsigned int port) return port & MV_PORT_MASK; } +/* + * Consolidate some rather tricky bit shift calculations. + * This is hot-path stuff, so not a function. + * Simple code, with two return values, so macro rather than inline. + * + * port is the sole input, in range 0..7. + * shift is one output, for use with main_irq_cause / main_irq_mask registers. + * hardport is the other output, in range 0..3. + * + * Note that port and hardport may be the same variable in some cases. + */ +#define MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport) \ +{ \ + shift = mv_hc_from_port(port) * HC_SHIFT; \ + hardport = mv_hardport_from_port(port); \ + shift += hardport * 2; \ +} + +static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc) +{ + return (base + SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ)); +} + static inline void __iomem *mv_hc_base_from_port(void __iomem *base, unsigned int port) { @@ -617,9 +913,23 @@ static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port) (mv_hardport_from_port(port) * MV_PORT_REG_SZ); } +static void __iomem *mv5_phy_base(void __iomem *mmio, unsigned int port) +{ + void __iomem *hc_mmio = mv_hc_base_from_port(mmio, port); + unsigned long ofs = (mv_hardport_from_port(port) + 1) * 0x100UL; + + return hc_mmio + ofs; +} + +static inline void __iomem *mv_host_base(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + return hpriv->base; +} + static inline void __iomem *mv_ap_base(struct ata_port *ap) { - return mv_port_base(ap->host->mmio_base, ap->port_no); + return mv_port_base(mv_host_base(ap->host), ap->port_no); } static inline int mv_get_hc_count(unsigned long port_flags) @@ -627,12 +937,225 @@ static inline int mv_get_hc_count(unsigned long port_flags) return ((port_flags & MV_FLAG_DUAL_HC) ? 2 : 1); } -static void mv_irq_clear(struct ata_port *ap) +/** + * mv_save_cached_regs - (re-)initialize cached port registers + * @ap: the port whose registers we are caching + * + * Initialize the local cache of port registers, + * so that reading them over and over again can + * be avoided on the hotter paths of this driver. + * This saves a few microseconds each time we switch + * to/from EDMA mode to perform (eg.) a drive cache flush. + */ +static void mv_save_cached_regs(struct ata_port *ap) { + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + + pp->cached.fiscfg = readl(port_mmio + FISCFG); + pp->cached.ltmode = readl(port_mmio + LTMODE); + pp->cached.haltcond = readl(port_mmio + EDMA_HALTCOND); + pp->cached.unknown_rsvd = readl(port_mmio + EDMA_UNKNOWN_RSVD); } /** - * mv_start_dma - Enable eDMA engine + * mv_write_cached_reg - write to a cached port register + * @addr: hardware address of the register + * @old: pointer to cached value of the register + * @new: new value for the register + * + * Write a new value to a cached register, + * but only if the value is different from before. + */ +static inline void mv_write_cached_reg(void __iomem *addr, u32 *old, u32 new) +{ + if (new != *old) { + unsigned long laddr; + *old = new; + /* + * Workaround for 88SX60x1-B2 FEr SATA#13: + * Read-after-write is needed to prevent generating 64-bit + * write cycles on the PCI bus for SATA interface registers + * at offsets ending in 0x4 or 0xc. + * + * Looks like a lot of fuss, but it avoids an unnecessary + * +1 usec read-after-write delay for unaffected registers. + */ + laddr = (long)addr & 0xffff; + if (laddr >= 0x300 && laddr <= 0x33c) { + laddr &= 0x000f; + if (laddr == 0x4 || laddr == 0xc) { + writelfl(new, addr); /* read after write */ + return; + } + } + writel(new, addr); /* unaffected by the errata */ + } +} + +static void mv_set_edma_ptrs(void __iomem *port_mmio, + struct mv_host_priv *hpriv, + struct mv_port_priv *pp) +{ + u32 index; + + /* + * initialize request queue + */ + pp->req_idx &= MV_MAX_Q_DEPTH_MASK; /* paranoia */ + index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT; + + WARN_ON(pp->crqb_dma & 0x3ff); + writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI); + writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index, + port_mmio + EDMA_REQ_Q_IN_PTR); + writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR); + + /* + * initialize response queue + */ + pp->resp_idx &= MV_MAX_Q_DEPTH_MASK; /* paranoia */ + index = pp->resp_idx << EDMA_RSP_Q_PTR_SHIFT; + + WARN_ON(pp->crpb_dma & 0xff); + writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI); + writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR); + writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index, + port_mmio + EDMA_RSP_Q_OUT_PTR); +} + +static void mv_write_main_irq_mask(u32 mask, struct mv_host_priv *hpriv) +{ + /* + * When writing to the main_irq_mask in hardware, + * we must ensure exclusivity between the interrupt coalescing bits + * and the corresponding individual port DONE_IRQ bits. + * + * Note that this register is really an "IRQ enable" register, + * not an "IRQ mask" register as Marvell's naming might suggest. + */ + if (mask & (ALL_PORTS_COAL_DONE | PORTS_0_3_COAL_DONE)) + mask &= ~DONE_IRQ_0_3; + if (mask & (ALL_PORTS_COAL_DONE | PORTS_4_7_COAL_DONE)) + mask &= ~DONE_IRQ_4_7; + writelfl(mask, hpriv->main_irq_mask_addr); +} + +static void mv_set_main_irq_mask(struct ata_host *host, + u32 disable_bits, u32 enable_bits) +{ + struct mv_host_priv *hpriv = host->private_data; + u32 old_mask, new_mask; + + old_mask = hpriv->main_irq_mask; + new_mask = (old_mask & ~disable_bits) | enable_bits; + if (new_mask != old_mask) { + hpriv->main_irq_mask = new_mask; + mv_write_main_irq_mask(new_mask, hpriv); + } +} + +static void mv_enable_port_irqs(struct ata_port *ap, + unsigned int port_bits) +{ + unsigned int shift, hardport, port = ap->port_no; + u32 disable_bits, enable_bits; + + MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport); + + disable_bits = (DONE_IRQ | ERR_IRQ) << shift; + enable_bits = port_bits << shift; + mv_set_main_irq_mask(ap->host, disable_bits, enable_bits); +} + +static void mv_clear_and_enable_port_irqs(struct ata_port *ap, + void __iomem *port_mmio, + unsigned int port_irqs) +{ + struct mv_host_priv *hpriv = ap->host->private_data; + int hardport = mv_hardport_from_port(ap->port_no); + void __iomem *hc_mmio = mv_hc_base_from_port( + mv_host_base(ap->host), ap->port_no); + u32 hc_irq_cause; + + /* clear EDMA event indicators, if any */ + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE); + + /* clear pending irq events */ + hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport); + writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE); + + /* clear FIS IRQ Cause */ + if (IS_GEN_IIE(hpriv)) + writelfl(0, port_mmio + FIS_IRQ_CAUSE); + + mv_enable_port_irqs(ap, port_irqs); +} + +static void mv_set_irq_coalescing(struct ata_host *host, + unsigned int count, unsigned int usecs) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base, *hc_mmio; + u32 coal_enable = 0; + unsigned long flags; + unsigned int clks, is_dual_hc = hpriv->n_ports > MV_PORTS_PER_HC; + const u32 coal_disable = PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE | + ALL_PORTS_COAL_DONE; + + /* Disable IRQ coalescing if either threshold is zero */ + if (!usecs || !count) { + clks = count = 0; + } else { + /* Respect maximum limits of the hardware */ + clks = usecs * COAL_CLOCKS_PER_USEC; + if (clks > MAX_COAL_TIME_THRESHOLD) + clks = MAX_COAL_TIME_THRESHOLD; + if (count > MAX_COAL_IO_COUNT) + count = MAX_COAL_IO_COUNT; + } + + spin_lock_irqsave(&host->lock, flags); + mv_set_main_irq_mask(host, coal_disable, 0); + + if (is_dual_hc && !IS_GEN_I(hpriv)) { + /* + * GEN_II/GEN_IIE with dual host controllers: + * one set of global thresholds for the entire chip. + */ + writel(clks, mmio + IRQ_COAL_TIME_THRESHOLD); + writel(count, mmio + IRQ_COAL_IO_THRESHOLD); + /* clear leftover coal IRQ bit */ + writel(~ALL_PORTS_COAL_IRQ, mmio + IRQ_COAL_CAUSE); + if (count) + coal_enable = ALL_PORTS_COAL_DONE; + clks = count = 0; /* force clearing of regular regs below */ + } + + /* + * All chips: independent thresholds for each HC on the chip. + */ + hc_mmio = mv_hc_base_from_port(mmio, 0); + writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD); + writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD); + writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE); + if (count) + coal_enable |= PORTS_0_3_COAL_DONE; + if (is_dual_hc) { + hc_mmio = mv_hc_base_from_port(mmio, MV_PORTS_PER_HC); + writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD); + writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD); + writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE); + if (count) + coal_enable |= PORTS_4_7_COAL_DONE; + } + + mv_set_main_irq_mask(host, 0, coal_enable); + spin_unlock_irqrestore(&host->lock, flags); +} + +/** + * mv_start_edma - Enable eDMA engine * @base: port base address * @pp: port private data * @@ -642,54 +1165,92 @@ static void mv_irq_clear(struct ata_port *ap) * LOCKING: * Inherited from caller. */ -static void mv_start_dma(void __iomem *base, struct mv_port_priv *pp) +static void mv_start_edma(struct ata_port *ap, void __iomem *port_mmio, + struct mv_port_priv *pp, u8 protocol) { - if (!(MV_PP_FLAG_EDMA_EN & pp->pp_flags)) { - writelfl(EDMA_EN, base + EDMA_CMD_OFS); + int want_ncq = (protocol == ATA_PROT_NCQ); + + if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) { + int using_ncq = ((pp->pp_flags & MV_PP_FLAG_NCQ_EN) != 0); + if (want_ncq != using_ncq) + mv_stop_edma(ap); + } + if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) { + struct mv_host_priv *hpriv = ap->host->private_data; + + mv_edma_cfg(ap, want_ncq, 1); + + mv_set_edma_ptrs(port_mmio, hpriv, pp); + mv_clear_and_enable_port_irqs(ap, port_mmio, DONE_IRQ|ERR_IRQ); + + writelfl(EDMA_EN, port_mmio + EDMA_CMD); pp->pp_flags |= MV_PP_FLAG_EDMA_EN; } - WARN_ON(!(EDMA_EN & readl(base + EDMA_CMD_OFS))); +} + +static void mv_wait_for_edma_empty_idle(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + const u32 empty_idle = (EDMA_STATUS_CACHE_EMPTY | EDMA_STATUS_IDLE); + const int per_loop = 5, timeout = (15 * 1000 / per_loop); + int i; + + /* + * Wait for the EDMA engine to finish transactions in progress. + * No idea what a good "timeout" value might be, but measurements + * indicate that it often requires hundreds of microseconds + * with two drives in-use. So we use the 15msec value above + * as a rough guess at what even more drives might require. + */ + for (i = 0; i < timeout; ++i) { + u32 edma_stat = readl(port_mmio + EDMA_STATUS); + if ((edma_stat & empty_idle) == empty_idle) + break; + udelay(per_loop); + } + /* ata_port_info(ap, "%s: %u+ usecs\n", __func__, i); */ } /** - * mv_stop_dma - Disable eDMA engine - * @ap: ATA channel to manipulate - * - * Verify the local cache of the eDMA state is accurate with a - * WARN_ON. + * mv_stop_edma_engine - Disable eDMA engine + * @port_mmio: io base address * * LOCKING: * Inherited from caller. */ -static void mv_stop_dma(struct ata_port *ap) +static int mv_stop_edma_engine(void __iomem *port_mmio) { - void __iomem *port_mmio = mv_ap_base(ap); - struct mv_port_priv *pp = ap->private_data; - u32 reg; int i; - if (MV_PP_FLAG_EDMA_EN & pp->pp_flags) { - /* Disable EDMA if active. The disable bit auto clears. - */ - writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS); - pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; - } else { - WARN_ON(EDMA_EN & readl(port_mmio + EDMA_CMD_OFS)); - } + /* Disable eDMA. The disable bit auto clears. */ + writelfl(EDMA_DS, port_mmio + EDMA_CMD); - /* now properly wait for the eDMA to stop */ - for (i = 1000; i > 0; i--) { - reg = readl(port_mmio + EDMA_CMD_OFS); - if (!(EDMA_EN & reg)) { - break; - } - udelay(100); + /* Wait for the chip to confirm eDMA is off. */ + for (i = 10000; i > 0; i--) { + u32 reg = readl(port_mmio + EDMA_CMD); + if (!(reg & EDMA_EN)) + return 0; + udelay(10); } + return -EIO; +} - if (EDMA_EN & reg) { - ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n"); - /* FIXME: Consider doing a reset here to recover */ +static int mv_stop_edma(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + int err = 0; + + if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) + return 0; + pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + mv_wait_for_edma_empty_idle(ap); + if (mv_stop_edma_engine(port_mmio)) { + ata_port_err(ap, "Unable to stop eDMA\n"); + err = -EIO; } + mv_edma_cfg(ap, 0, 0); + return err; } #ifdef ATA_DEBUG @@ -699,14 +1260,14 @@ static void mv_dump_mem(void __iomem *start, unsigned bytes) for (b = 0; b < bytes; ) { DPRINTK("%p: ", start + b); for (w = 0; b < bytes && w < 4; w++) { - printk("%08x ",readl(start + b)); + printk("%08x ", readl(start + b)); b += sizeof(u32); } printk("\n"); } } #endif - +#if defined(ATA_DEBUG) || defined(CONFIG_PCI) static void mv_dump_pci_cfg(struct pci_dev *pdev, unsigned bytes) { #ifdef ATA_DEBUG @@ -715,14 +1276,15 @@ static void mv_dump_pci_cfg(struct pci_dev *pdev, unsigned bytes) for (b = 0; b < bytes; ) { DPRINTK("%02x: ", b); for (w = 0; b < bytes && w < 4; w++) { - (void) pci_read_config_dword(pdev,b,&dw); - printk("%08x ",dw); + (void) pci_read_config_dword(pdev, b, &dw); + printk("%08x ", dw); b += sizeof(u32); } printk("\n"); } #endif } +#endif static void mv_dump_all_regs(void __iomem *mmio_base, int port, struct pci_dev *pdev) { @@ -760,9 +1322,9 @@ static void mv_dump_all_regs(void __iomem *mmio_base, int port, } for (p = start_port; p < start_port + num_ports; p++) { port_base = mv_port_base(mmio_base, p); - DPRINTK("EDMA regs (port %i):\n",p); + DPRINTK("EDMA regs (port %i):\n", p); mv_dump_mem(port_base, 0x54); - DPRINTK("SATA regs (port %i):\n",p); + DPRINTK("SATA regs (port %i):\n", p); mv_dump_mem(port_base+0x300, 0x60); } #endif @@ -776,10 +1338,10 @@ static unsigned int mv_scr_offset(unsigned int sc_reg_in) case SCR_STATUS: case SCR_CONTROL: case SCR_ERROR: - ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32)); + ofs = SATA_STATUS + (sc_reg_in * sizeof(u32)); break; case SCR_ACTIVE: - ofs = SATA_ACTIVE_OFS; /* active is not with the others */ + ofs = SATA_ACTIVE; /* active is not with the others */ break; default: ofs = 0xffffffffU; @@ -788,80 +1350,346 @@ static unsigned int mv_scr_offset(unsigned int sc_reg_in) return ofs; } -static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in) +static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val) { unsigned int ofs = mv_scr_offset(sc_reg_in); - if (0xffffffffU != ofs) { - return readl(mv_ap_base(ap) + ofs); - } else { - return (u32) ofs; - } + if (ofs != 0xffffffffU) { + *val = readl(mv_ap_base(link->ap) + ofs); + return 0; + } else + return -EINVAL; } -static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) +static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val) { unsigned int ofs = mv_scr_offset(sc_reg_in); - if (0xffffffffU != ofs) { - writelfl(val, mv_ap_base(ap) + ofs); + if (ofs != 0xffffffffU) { + void __iomem *addr = mv_ap_base(link->ap) + ofs; + struct mv_host_priv *hpriv = link->ap->host->private_data; + if (sc_reg_in == SCR_CONTROL) { + /* + * Workaround for 88SX60x1 FEr SATA#26: + * + * COMRESETs have to take care not to accidentally + * put the drive to sleep when writing SCR_CONTROL. + * Setting bits 12..15 prevents this problem. + * + * So if we see an outbound COMMRESET, set those bits. + * Ditto for the followup write that clears the reset. + * + * The proprietary driver does this for + * all chip versions, and so do we. + */ + if ((val & 0xf) == 1 || (readl(addr) & 0xf) == 1) + val |= 0xf000; + + if (hpriv->hp_flags & MV_HP_FIX_LP_PHY_CTL) { + void __iomem *lp_phy_addr = + mv_ap_base(link->ap) + LP_PHY_CTL; + /* + * Set PHY speed according to SControl speed. + */ + if ((val & 0xf0) == 0x10) + writelfl(0x7, lp_phy_addr); + else + writelfl(0x227, lp_phy_addr); + } + } + writelfl(val, addr); + return 0; + } else + return -EINVAL; +} + +static void mv6_dev_config(struct ata_device *adev) +{ + /* + * Deal with Gen-II ("mv6") hardware quirks/restrictions: + * + * Gen-II does not support NCQ over a port multiplier + * (no FIS-based switching). + */ + if (adev->flags & ATA_DFLAG_NCQ) { + if (sata_pmp_attached(adev->link->ap)) { + adev->flags &= ~ATA_DFLAG_NCQ; + ata_dev_info(adev, + "NCQ disabled for command-based switching\n"); + } + } +} + +static int mv_qc_defer(struct ata_queued_cmd *qc) +{ + struct ata_link *link = qc->dev->link; + struct ata_port *ap = link->ap; + struct mv_port_priv *pp = ap->private_data; + + /* + * Don't allow new commands if we're in a delayed EH state + * for NCQ and/or FIS-based switching. + */ + if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) + return ATA_DEFER_PORT; + + /* PIO commands need exclusive link: no other commands [DMA or PIO] + * can run concurrently. + * set excl_link when we want to send a PIO command in DMA mode + * or a non-NCQ command in NCQ mode. + * When we receive a command from that link, and there are no + * outstanding commands, mark a flag to clear excl_link and let + * the command go through. + */ + if (unlikely(ap->excl_link)) { + if (link == ap->excl_link) { + if (ap->nr_active_links) + return ATA_DEFER_PORT; + qc->flags |= ATA_QCFLAG_CLEAR_EXCL; + return 0; + } else + return ATA_DEFER_PORT; + } + + /* + * If the port is completely idle, then allow the new qc. + */ + if (ap->nr_active_links == 0) + return 0; + + /* + * The port is operating in host queuing mode (EDMA) with NCQ + * enabled, allow multiple NCQ commands. EDMA also allows + * queueing multiple DMA commands but libata core currently + * doesn't allow it. + */ + if ((pp->pp_flags & MV_PP_FLAG_EDMA_EN) && + (pp->pp_flags & MV_PP_FLAG_NCQ_EN)) { + if (ata_is_ncq(qc->tf.protocol)) + return 0; + else { + ap->excl_link = link; + return ATA_DEFER_PORT; + } } + + return ATA_DEFER_PORT; +} + +static void mv_config_fbs(struct ata_port *ap, int want_ncq, int want_fbs) +{ + struct mv_port_priv *pp = ap->private_data; + void __iomem *port_mmio; + + u32 fiscfg, *old_fiscfg = &pp->cached.fiscfg; + u32 ltmode, *old_ltmode = &pp->cached.ltmode; + u32 haltcond, *old_haltcond = &pp->cached.haltcond; + + ltmode = *old_ltmode & ~LTMODE_BIT8; + haltcond = *old_haltcond | EDMA_ERR_DEV; + + if (want_fbs) { + fiscfg = *old_fiscfg | FISCFG_SINGLE_SYNC; + ltmode = *old_ltmode | LTMODE_BIT8; + if (want_ncq) + haltcond &= ~EDMA_ERR_DEV; + else + fiscfg |= FISCFG_WAIT_DEV_ERR; + } else { + fiscfg = *old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR); + } + + port_mmio = mv_ap_base(ap); + mv_write_cached_reg(port_mmio + FISCFG, old_fiscfg, fiscfg); + mv_write_cached_reg(port_mmio + LTMODE, old_ltmode, ltmode); + mv_write_cached_reg(port_mmio + EDMA_HALTCOND, old_haltcond, haltcond); +} + +static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq) +{ + struct mv_host_priv *hpriv = ap->host->private_data; + u32 old, new; + + /* workaround for 88SX60x1 FEr SATA#25 (part 1) */ + old = readl(hpriv->base + GPIO_PORT_CTL); + if (want_ncq) + new = old | (1 << 22); + else + new = old & ~(1 << 22); + if (new != old) + writel(new, hpriv->base + GPIO_PORT_CTL); } /** - * mv_host_stop - Host specific cleanup/stop routine. - * @host: host data structure + * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma + * @ap: Port being initialized * - * Disable ints, cleanup host memory, call general purpose - * host_stop. + * There are two DMA modes on these chips: basic DMA, and EDMA. * - * LOCKING: - * Inherited from caller. + * Bit-0 of the "EDMA RESERVED" register enables/disables use + * of basic DMA on the GEN_IIE versions of the chips. + * + * This bit survives EDMA resets, and must be set for basic DMA + * to function, and should be cleared when EDMA is active. + */ +static void mv_bmdma_enable_iie(struct ata_port *ap, int enable_bmdma) +{ + struct mv_port_priv *pp = ap->private_data; + u32 new, *old = &pp->cached.unknown_rsvd; + + if (enable_bmdma) + new = *old | 1; + else + new = *old & ~1; + mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD, old, new); +} + +/* + * SOC chips have an issue whereby the HDD LEDs don't always blink + * during I/O when NCQ is enabled. Enabling a special "LED blink" mode + * of the SOC takes care of it, generating a steady blink rate when + * any drive on the chip is active. + * + * Unfortunately, the blink mode is a global hardware setting for the SOC, + * so we must use it whenever at least one port on the SOC has NCQ enabled. + * + * We turn "LED blink" off when NCQ is not in use anywhere, because the normal + * LED operation works then, and provides better (more accurate) feedback. + * + * Note that this code assumes that an SOC never has more than one HC onboard. */ -static void mv_host_stop(struct ata_host *host) +static void mv_soc_led_blink_enable(struct ata_port *ap) { + struct ata_host *host = ap->host; struct mv_host_priv *hpriv = host->private_data; - struct pci_dev *pdev = to_pci_dev(host->dev); + void __iomem *hc_mmio; + u32 led_ctrl; - if (hpriv->hp_flags & MV_HP_FLAG_MSI) { - pci_disable_msi(pdev); - } else { - pci_intx(pdev, 0); - } - kfree(hpriv); - ata_host_stop(host); + if (hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN) + return; + hpriv->hp_flags |= MV_HP_QUIRK_LED_BLINK_EN; + hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no); + led_ctrl = readl(hc_mmio + SOC_LED_CTRL); + writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL); } -static inline void mv_priv_free(struct mv_port_priv *pp, struct device *dev) +static void mv_soc_led_blink_disable(struct ata_port *ap) { - dma_free_coherent(dev, MV_PORT_PRIV_DMA_SZ, pp->crpb, pp->crpb_dma); + struct ata_host *host = ap->host; + struct mv_host_priv *hpriv = host->private_data; + void __iomem *hc_mmio; + u32 led_ctrl; + unsigned int port; + + if (!(hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN)) + return; + + /* disable led-blink only if no ports are using NCQ */ + for (port = 0; port < hpriv->n_ports; port++) { + struct ata_port *this_ap = host->ports[port]; + struct mv_port_priv *pp = this_ap->private_data; + + if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) + return; + } + + hpriv->hp_flags &= ~MV_HP_QUIRK_LED_BLINK_EN; + hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no); + led_ctrl = readl(hc_mmio + SOC_LED_CTRL); + writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL); } -static void mv_edma_cfg(struct mv_host_priv *hpriv, void __iomem *port_mmio) +static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma) { - u32 cfg = readl(port_mmio + EDMA_CFG_OFS); + u32 cfg; + struct mv_port_priv *pp = ap->private_data; + struct mv_host_priv *hpriv = ap->host->private_data; + void __iomem *port_mmio = mv_ap_base(ap); /* set up non-NCQ EDMA configuration */ - cfg &= ~0x1f; /* clear queue depth */ - cfg &= ~EDMA_CFG_NCQ; /* clear NCQ mode */ - cfg &= ~(1 << 9); /* disable equeue */ + cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */ + pp->pp_flags &= + ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY); if (IS_GEN_I(hpriv)) cfg |= (1 << 8); /* enab config burst size mask */ - else if (IS_GEN_II(hpriv)) + else if (IS_GEN_II(hpriv)) { cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN; + mv_60x1_errata_sata25(ap, want_ncq); + + } else if (IS_GEN_IIE(hpriv)) { + int want_fbs = sata_pmp_attached(ap); + /* + * Possible future enhancement: + * + * The chip can use FBS with non-NCQ, if we allow it, + * But first we need to have the error handling in place + * for this mode (datasheet section 7.3.15.4.2.3). + * So disallow non-NCQ FBS for now. + */ + want_fbs &= want_ncq; + + mv_config_fbs(ap, want_ncq, want_fbs); + + if (want_fbs) { + pp->pp_flags |= MV_PP_FLAG_FBS_EN; + cfg |= EDMA_CFG_EDMA_FBS; /* FIS-based switching */ + } + + cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */ + if (want_edma) { + cfg |= (1 << 22); /* enab 4-entry host queue cache */ + if (!IS_SOC(hpriv)) + cfg |= (1 << 18); /* enab early completion */ + } + if (hpriv->hp_flags & MV_HP_CUT_THROUGH) + cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */ + mv_bmdma_enable_iie(ap, !want_edma); + + if (IS_SOC(hpriv)) { + if (want_ncq) + mv_soc_led_blink_enable(ap); + else + mv_soc_led_blink_disable(ap); + } + } - else if (IS_GEN_IIE(hpriv)) { - cfg |= (1 << 23); /* dis RX PM port mask */ - cfg &= ~(1 << 16); /* dis FIS-based switching (for now) */ - cfg &= ~(1 << 19); /* dis 128-entry queue (for now?) */ - cfg |= (1 << 18); /* enab early completion */ - cfg |= (1 << 17); /* enab host q cache */ - cfg |= (1 << 22); /* enab cutthrough */ + if (want_ncq) { + cfg |= EDMA_CFG_NCQ; + pp->pp_flags |= MV_PP_FLAG_NCQ_EN; } - writelfl(cfg, port_mmio + EDMA_CFG_OFS); + writelfl(cfg, port_mmio + EDMA_CFG); +} + +static void mv_port_free_dma_mem(struct ata_port *ap) +{ + struct mv_host_priv *hpriv = ap->host->private_data; + struct mv_port_priv *pp = ap->private_data; + int tag; + + if (pp->crqb) { + dma_pool_free(hpriv->crqb_pool, pp->crqb, pp->crqb_dma); + pp->crqb = NULL; + } + if (pp->crpb) { + dma_pool_free(hpriv->crpb_pool, pp->crpb, pp->crpb_dma); + pp->crpb = NULL; + } + /* + * For GEN_I, there's no NCQ, so we have only a single sg_tbl. + * For later hardware, we have one unique sg_tbl per NCQ tag. + */ + for (tag = 0; tag < MV_MAX_Q_DEPTH; ++tag) { + if (pp->sg_tbl[tag]) { + if (tag == 0 || !IS_GEN_I(hpriv)) + dma_pool_free(hpriv->sg_tbl_pool, + pp->sg_tbl[tag], + pp->sg_tbl_dma[tag]); + pp->sg_tbl[tag] = NULL; + } + } } /** @@ -879,84 +1707,53 @@ static int mv_port_start(struct ata_port *ap) struct device *dev = ap->host->dev; struct mv_host_priv *hpriv = ap->host->private_data; struct mv_port_priv *pp; - void __iomem *port_mmio = mv_ap_base(ap); - void *mem; - dma_addr_t mem_dma; - int rc = -ENOMEM; + unsigned long flags; + int tag; - pp = kmalloc(sizeof(*pp), GFP_KERNEL); + pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL); if (!pp) - goto err_out; - memset(pp, 0, sizeof(*pp)); - - mem = dma_alloc_coherent(dev, MV_PORT_PRIV_DMA_SZ, &mem_dma, - GFP_KERNEL); - if (!mem) - goto err_out_pp; - memset(mem, 0, MV_PORT_PRIV_DMA_SZ); - - rc = ata_pad_alloc(ap, dev); - if (rc) - goto err_out_priv; - - /* First item in chunk of DMA memory: - * 32-slot command request table (CRQB), 32 bytes each in size - */ - pp->crqb = mem; - pp->crqb_dma = mem_dma; - mem += MV_CRQB_Q_SZ; - mem_dma += MV_CRQB_Q_SZ; - - /* Second item: - * 32-slot command response table (CRPB), 8 bytes each in size - */ - pp->crpb = mem; - pp->crpb_dma = mem_dma; - mem += MV_CRPB_Q_SZ; - mem_dma += MV_CRPB_Q_SZ; + return -ENOMEM; + ap->private_data = pp; - /* Third item: - * Table of scatter-gather descriptors (ePRD), 16 bytes each + pp->crqb = dma_pool_alloc(hpriv->crqb_pool, GFP_KERNEL, &pp->crqb_dma); + if (!pp->crqb) + return -ENOMEM; + memset(pp->crqb, 0, MV_CRQB_Q_SZ); + + pp->crpb = dma_pool_alloc(hpriv->crpb_pool, GFP_KERNEL, &pp->crpb_dma); + if (!pp->crpb) + goto out_port_free_dma_mem; + memset(pp->crpb, 0, MV_CRPB_Q_SZ); + + /* 6041/6081 Rev. "C0" (and newer) are okay with async notify */ + if (hpriv->hp_flags & MV_HP_ERRATA_60X1C0) + ap->flags |= ATA_FLAG_AN; + /* + * For GEN_I, there's no NCQ, so we only allocate a single sg_tbl. + * For later hardware, we need one unique sg_tbl per NCQ tag. */ - pp->sg_tbl = mem; - pp->sg_tbl_dma = mem_dma; - - mv_edma_cfg(hpriv, port_mmio); - - writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS); - writelfl(pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK, - port_mmio + EDMA_REQ_Q_IN_PTR_OFS); - - if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) - writelfl(pp->crqb_dma & 0xffffffff, - port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); - else - writelfl(0, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); - - writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS); - - if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) - writelfl(pp->crpb_dma & 0xffffffff, - port_mmio + EDMA_RSP_Q_IN_PTR_OFS); - else - writelfl(0, port_mmio + EDMA_RSP_Q_IN_PTR_OFS); + for (tag = 0; tag < MV_MAX_Q_DEPTH; ++tag) { + if (tag == 0 || !IS_GEN_I(hpriv)) { + pp->sg_tbl[tag] = dma_pool_alloc(hpriv->sg_tbl_pool, + GFP_KERNEL, &pp->sg_tbl_dma[tag]); + if (!pp->sg_tbl[tag]) + goto out_port_free_dma_mem; + } else { + pp->sg_tbl[tag] = pp->sg_tbl[0]; + pp->sg_tbl_dma[tag] = pp->sg_tbl_dma[0]; + } + } - writelfl(pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK, - port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); + spin_lock_irqsave(ap->lock, flags); + mv_save_cached_regs(ap); + mv_edma_cfg(ap, 0, 0); + spin_unlock_irqrestore(ap->lock, flags); - /* Don't turn on EDMA here...do it before DMA commands only. Else - * we'll be unable to send non-data, PIO, etc due to restricted access - * to shadow regs. - */ - ap->private_data = pp; return 0; -err_out_priv: - mv_priv_free(pp, dev); -err_out_pp: - kfree(pp); -err_out: - return rc; +out_port_free_dma_mem: + mv_port_free_dma_mem(ap); + return -ENOMEM; } /** @@ -970,18 +1767,13 @@ err_out: */ static void mv_port_stop(struct ata_port *ap) { - struct device *dev = ap->host->dev; - struct mv_port_priv *pp = ap->private_data; unsigned long flags; - spin_lock_irqsave(&ap->host->lock, flags); - mv_stop_dma(ap); - spin_unlock_irqrestore(&ap->host->lock, flags); - - ap->private_data = NULL; - ata_pad_free(ap, dev); - mv_priv_free(pp, dev); - kfree(pp); + spin_lock_irqsave(ap->lock, flags); + mv_stop_edma(ap); + mv_enable_port_irqs(ap, 0); + spin_unlock_irqrestore(ap->lock, flags); + mv_port_free_dma_mem(ap); } /** @@ -996,43 +1788,41 @@ static void mv_port_stop(struct ata_port *ap) static void mv_fill_sg(struct ata_queued_cmd *qc) { struct mv_port_priv *pp = qc->ap->private_data; - unsigned int i = 0; struct scatterlist *sg; + struct mv_sg *mv_sg, *last_sg = NULL; + unsigned int si; - ata_for_each_sg(sg, qc) { - dma_addr_t addr; - u32 sg_len, len, offset; - - addr = sg_dma_address(sg); - sg_len = sg_dma_len(sg); + mv_sg = pp->sg_tbl[qc->tag]; + for_each_sg(qc->sg, sg, qc->n_elem, si) { + dma_addr_t addr = sg_dma_address(sg); + u32 sg_len = sg_dma_len(sg); while (sg_len) { - offset = addr & MV_DMA_BOUNDARY; - len = sg_len; - if ((offset + sg_len) > 0x10000) + u32 offset = addr & 0xffff; + u32 len = sg_len; + + if (offset + len > 0x10000) len = 0x10000 - offset; - pp->sg_tbl[i].addr = cpu_to_le32(addr & 0xffffffff); - pp->sg_tbl[i].addr_hi = cpu_to_le32((addr >> 16) >> 16); - pp->sg_tbl[i].flags_size = cpu_to_le32(len & 0xffff); + mv_sg->addr = cpu_to_le32(addr & 0xffffffff); + mv_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16); + mv_sg->flags_size = cpu_to_le32(len & 0xffff); + mv_sg->reserved = 0; sg_len -= len; addr += len; - if (!sg_len && ata_sg_is_last(sg, qc)) - pp->sg_tbl[i].flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL); - - i++; + last_sg = mv_sg; + mv_sg++; } } -} -static inline unsigned mv_inc_q_index(unsigned index) -{ - return (index + 1) & MV_MAX_Q_DEPTH_MASK; + if (likely(last_sg)) + last_sg->flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL); + mb(); /* ensure data structure is visible to the chipset */ } -static inline void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last) +static void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last) { u16 tmp = data | (addr << CRQB_CMD_ADDR_SHIFT) | CRQB_CMD_CS | (last ? CRQB_CMD_LAST : 0); @@ -1040,6 +1830,199 @@ static inline void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned las } /** + * mv_sff_irq_clear - Clear hardware interrupt after DMA. + * @ap: Port associated with this ATA transaction. + * + * We need this only for ATAPI bmdma transactions, + * as otherwise we experience spurious interrupts + * after libata-sff handles the bmdma interrupts. + */ +static void mv_sff_irq_clear(struct ata_port *ap) +{ + mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), ERR_IRQ); +} + +/** + * mv_check_atapi_dma - Filter ATAPI cmds which are unsuitable for DMA. + * @qc: queued command to check for chipset/DMA compatibility. + * + * The bmdma engines cannot handle speculative data sizes + * (bytecount under/over flow). So only allow DMA for + * data transfer commands with known data sizes. + * + * LOCKING: + * Inherited from caller. + */ +static int mv_check_atapi_dma(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *scmd = qc->scsicmd; + + if (scmd) { + switch (scmd->cmnd[0]) { + case READ_6: + case READ_10: + case READ_12: + case WRITE_6: + case WRITE_10: + case WRITE_12: + case GPCMD_READ_CD: + case GPCMD_SEND_DVD_STRUCTURE: + case GPCMD_SEND_CUE_SHEET: + return 0; /* DMA is safe */ + } + } + return -EOPNOTSUPP; /* use PIO instead */ +} + +/** + * mv_bmdma_setup - Set up BMDMA transaction + * @qc: queued command to prepare DMA for. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_bmdma_setup(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + + mv_fill_sg(qc); + + /* clear all DMA cmd bits */ + writel(0, port_mmio + BMDMA_CMD); + + /* load PRD table addr. */ + writel((pp->sg_tbl_dma[qc->tag] >> 16) >> 16, + port_mmio + BMDMA_PRD_HIGH); + writelfl(pp->sg_tbl_dma[qc->tag], + port_mmio + BMDMA_PRD_LOW); + + /* issue r/w command */ + ap->ops->sff_exec_command(ap, &qc->tf); +} + +/** + * mv_bmdma_start - Start a BMDMA transaction + * @qc: queued command to start DMA on. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = mv_ap_base(ap); + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u32 cmd = (rw ? 0 : ATA_DMA_WR) | ATA_DMA_START; + + /* start host DMA transaction */ + writelfl(cmd, port_mmio + BMDMA_CMD); +} + +/** + * mv_bmdma_stop - Stop BMDMA transfer + * @qc: queued command to stop DMA on. + * + * Clears the ATA_DMA_START flag in the bmdma control register + * + * LOCKING: + * Inherited from caller. + */ +static void mv_bmdma_stop_ap(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 cmd; + + /* clear start/stop bit */ + cmd = readl(port_mmio + BMDMA_CMD); + if (cmd & ATA_DMA_START) { + cmd &= ~ATA_DMA_START; + writelfl(cmd, port_mmio + BMDMA_CMD); + + /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ + ata_sff_dma_pause(ap); + } +} + +static void mv_bmdma_stop(struct ata_queued_cmd *qc) +{ + mv_bmdma_stop_ap(qc->ap); +} + +/** + * mv_bmdma_status - Read BMDMA status + * @ap: port for which to retrieve DMA status. + * + * Read and return equivalent of the sff BMDMA status register. + * + * LOCKING: + * Inherited from caller. + */ +static u8 mv_bmdma_status(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 reg, status; + + /* + * Other bits are valid only if ATA_DMA_ACTIVE==0, + * and the ATA_DMA_INTR bit doesn't exist. + */ + reg = readl(port_mmio + BMDMA_STATUS); + if (reg & ATA_DMA_ACTIVE) + status = ATA_DMA_ACTIVE; + else if (reg & ATA_DMA_ERR) + status = (reg & ATA_DMA_ERR) | ATA_DMA_INTR; + else { + /* + * Just because DMA_ACTIVE is 0 (DMA completed), + * this does _not_ mean the device is "done". + * So we should not yet be signalling ATA_DMA_INTR + * in some cases. Eg. DSM/TRIM, and perhaps others. + */ + mv_bmdma_stop_ap(ap); + if (ioread8(ap->ioaddr.altstatus_addr) & ATA_BUSY) + status = 0; + else + status = ATA_DMA_INTR; + } + return status; +} + +static void mv_rw_multi_errata_sata24(struct ata_queued_cmd *qc) +{ + struct ata_taskfile *tf = &qc->tf; + /* + * Workaround for 88SX60x1 FEr SATA#24. + * + * Chip may corrupt WRITEs if multi_count >= 4kB. + * Note that READs are unaffected. + * + * It's not clear if this errata really means "4K bytes", + * or if it always happens for multi_count > 7 + * regardless of device sector_size. + * + * So, for safety, any write with multi_count > 7 + * gets converted here into a regular PIO write instead: + */ + if ((tf->flags & ATA_TFLAG_WRITE) && is_multi_taskfile(tf)) { + if (qc->dev->multi_count > 7) { + switch (tf->command) { + case ATA_CMD_WRITE_MULTI: + tf->command = ATA_CMD_PIO_WRITE; + break; + case ATA_CMD_WRITE_MULTI_FUA_EXT: + tf->flags &= ~ATA_TFLAG_FUA; /* ugh */ + /* fall through */ + case ATA_CMD_WRITE_MULTI_EXT: + tf->command = ATA_CMD_PIO_WRITE_EXT; + break; + } + } + } +} + +/** * mv_qc_prep - Host specific command preparation. * @qc: queued command to prepare * @@ -1056,38 +2039,49 @@ static void mv_qc_prep(struct ata_queued_cmd *qc) struct ata_port *ap = qc->ap; struct mv_port_priv *pp = ap->private_data; __le16 *cw; - struct ata_taskfile *tf; + struct ata_taskfile *tf = &qc->tf; u16 flags = 0; unsigned in_index; - if (ATA_PROT_DMA != qc->tf.protocol) + switch (tf->protocol) { + case ATA_PROT_DMA: + if (tf->command == ATA_CMD_DSM) + return; + /* fall-thru */ + case ATA_PROT_NCQ: + break; /* continue below */ + case ATA_PROT_PIO: + mv_rw_multi_errata_sata24(qc); return; + default: + return; + } /* Fill in command request block */ - if (!(qc->tf.flags & ATA_TFLAG_WRITE)) + if (!(tf->flags & ATA_TFLAG_WRITE)) flags |= CRQB_FLAG_READ; WARN_ON(MV_MAX_Q_DEPTH <= qc->tag); flags |= qc->tag << CRQB_TAG_SHIFT; + flags |= (qc->dev->link->pmp & 0xf) << CRQB_PMP_SHIFT; - /* get current queue index from hardware */ - in_index = (readl(mv_ap_base(ap) + EDMA_REQ_Q_IN_PTR_OFS) - >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + /* get current queue index from software */ + in_index = pp->req_idx; pp->crqb[in_index].sg_addr = - cpu_to_le32(pp->sg_tbl_dma & 0xffffffff); + cpu_to_le32(pp->sg_tbl_dma[qc->tag] & 0xffffffff); pp->crqb[in_index].sg_addr_hi = - cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16); + cpu_to_le32((pp->sg_tbl_dma[qc->tag] >> 16) >> 16); pp->crqb[in_index].ctrl_flags = cpu_to_le16(flags); cw = &pp->crqb[in_index].ata_cmd[0]; - tf = &qc->tf; - /* Sadly, the CRQB cannot accomodate all registers--there are + /* Sadly, the CRQB cannot accommodate all registers--there are * only 11 bytes...so we must pick and choose required * registers based on the command. So, we drop feature and * hob_feature for [RW] DMA commands, but they are needed for - * NCQ. NCQ will drop hob_nsect. + * NCQ. NCQ will drop hob_nsect, which is not needed there + * (nsect is used only for the tag; feat/hob_feat hold true nsect). */ switch (tf->command) { case ATA_CMD_READ: @@ -1097,13 +2091,11 @@ static void mv_qc_prep(struct ata_queued_cmd *qc) case ATA_CMD_WRITE_FUA_EXT: mv_crqb_pack_cmd(cw++, tf->hob_nsect, ATA_REG_NSECT, 0); break; -#ifdef LIBATA_NCQ /* FIXME: remove this line when NCQ added */ case ATA_CMD_FPDMA_READ: case ATA_CMD_FPDMA_WRITE: mv_crqb_pack_cmd(cw++, tf->hob_feature, ATA_REG_FEATURE, 0); mv_crqb_pack_cmd(cw++, tf->feature, ATA_REG_FEATURE, 0); break; -#endif /* FIXME: remove this line when NCQ added */ default: /* The only other commands EDMA supports in non-queued and * non-NCQ mode are: [RW] STREAM DMA and W DMA FUA EXT, none @@ -1148,31 +2140,33 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) struct ata_port *ap = qc->ap; struct mv_port_priv *pp = ap->private_data; struct mv_crqb_iie *crqb; - struct ata_taskfile *tf; + struct ata_taskfile *tf = &qc->tf; unsigned in_index; u32 flags = 0; - if (ATA_PROT_DMA != qc->tf.protocol) + if ((tf->protocol != ATA_PROT_DMA) && + (tf->protocol != ATA_PROT_NCQ)) return; + if (tf->command == ATA_CMD_DSM) + return; /* use bmdma for this */ - /* Fill in Gen IIE command request block - */ - if (!(qc->tf.flags & ATA_TFLAG_WRITE)) + /* Fill in Gen IIE command request block */ + if (!(tf->flags & ATA_TFLAG_WRITE)) flags |= CRQB_FLAG_READ; WARN_ON(MV_MAX_Q_DEPTH <= qc->tag); flags |= qc->tag << CRQB_TAG_SHIFT; + flags |= qc->tag << CRQB_HOSTQ_SHIFT; + flags |= (qc->dev->link->pmp & 0xf) << CRQB_PMP_SHIFT; - /* get current queue index from hardware */ - in_index = (readl(mv_ap_base(ap) + EDMA_REQ_Q_IN_PTR_OFS) - >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + /* get current queue index from software */ + in_index = pp->req_idx; crqb = (struct mv_crqb_iie *) &pp->crqb[in_index]; - crqb->addr = cpu_to_le32(pp->sg_tbl_dma & 0xffffffff); - crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16); + crqb->addr = cpu_to_le32(pp->sg_tbl_dma[qc->tag] & 0xffffffff); + crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma[qc->tag] >> 16) >> 16); crqb->flags = cpu_to_le32(flags); - tf = &qc->tf; crqb->ata_cmd[0] = cpu_to_le32( (tf->command << 16) | (tf->feature << 24) @@ -1200,6 +2194,131 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) } /** + * mv_sff_check_status - fetch device status, if valid + * @ap: ATA port to fetch status from + * + * When using command issue via mv_qc_issue_fis(), + * the initial ATA_BUSY state does not show up in the + * ATA status (shadow) register. This can confuse libata! + * + * So we have a hook here to fake ATA_BUSY for that situation, + * until the first time a BUSY, DRQ, or ERR bit is seen. + * + * The rest of the time, it simply returns the ATA status register. + */ +static u8 mv_sff_check_status(struct ata_port *ap) +{ + u8 stat = ioread8(ap->ioaddr.status_addr); + struct mv_port_priv *pp = ap->private_data; + + if (pp->pp_flags & MV_PP_FLAG_FAKE_ATA_BUSY) { + if (stat & (ATA_BUSY | ATA_DRQ | ATA_ERR)) + pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY; + else + stat = ATA_BUSY; + } + return stat; +} + +/** + * mv_send_fis - Send a FIS, using the "Vendor-Unique FIS" register + * @fis: fis to be sent + * @nwords: number of 32-bit words in the fis + */ +static unsigned int mv_send_fis(struct ata_port *ap, u32 *fis, int nwords) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 ifctl, old_ifctl, ifstat; + int i, timeout = 200, final_word = nwords - 1; + + /* Initiate FIS transmission mode */ + old_ifctl = readl(port_mmio + SATA_IFCTL); + ifctl = 0x100 | (old_ifctl & 0xf); + writelfl(ifctl, port_mmio + SATA_IFCTL); + + /* Send all words of the FIS except for the final word */ + for (i = 0; i < final_word; ++i) + writel(fis[i], port_mmio + VENDOR_UNIQUE_FIS); + + /* Flag end-of-transmission, and then send the final word */ + writelfl(ifctl | 0x200, port_mmio + SATA_IFCTL); + writelfl(fis[final_word], port_mmio + VENDOR_UNIQUE_FIS); + + /* + * Wait for FIS transmission to complete. + * This typically takes just a single iteration. + */ + do { + ifstat = readl(port_mmio + SATA_IFSTAT); + } while (!(ifstat & 0x1000) && --timeout); + + /* Restore original port configuration */ + writelfl(old_ifctl, port_mmio + SATA_IFCTL); + + /* See if it worked */ + if ((ifstat & 0x3000) != 0x1000) { + ata_port_warn(ap, "%s transmission error, ifstat=%08x\n", + __func__, ifstat); + return AC_ERR_OTHER; + } + return 0; +} + +/** + * mv_qc_issue_fis - Issue a command directly as a FIS + * @qc: queued command to start + * + * Note that the ATA shadow registers are not updated + * after command issue, so the device will appear "READY" + * if polled, even while it is BUSY processing the command. + * + * So we use a status hook to fake ATA_BUSY until the drive changes state. + * + * Note: we don't get updated shadow regs on *completion* + * of non-data commands. So avoid sending them via this function, + * as they will appear to have completed immediately. + * + * GEN_IIE has special registers that we could get the result tf from, + * but earlier chipsets do not. For now, we ignore those registers. + */ +static unsigned int mv_qc_issue_fis(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct mv_port_priv *pp = ap->private_data; + struct ata_link *link = qc->dev->link; + u32 fis[5]; + int err = 0; + + ata_tf_to_fis(&qc->tf, link->pmp, 1, (void *)fis); + err = mv_send_fis(ap, fis, ARRAY_SIZE(fis)); + if (err) + return err; + + switch (qc->tf.protocol) { + case ATAPI_PROT_PIO: + pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY; + /* fall through */ + case ATAPI_PROT_NODATA: + ap->hsm_task_state = HSM_ST_FIRST; + break; + case ATA_PROT_PIO: + pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY; + if (qc->tf.flags & ATA_TFLAG_WRITE) + ap->hsm_task_state = HSM_ST_FIRST; + else + ap->hsm_task_state = HSM_ST; + break; + default: + ap->hsm_task_state = HSM_ST_LAST; + break; + } + + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_sff_queue_pio_task(link, 0); + return 0; +} + +/** * mv_qc_issue - Initiate a command to the host * @qc: queued command to start * @@ -1213,230 +2332,666 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) */ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc) { - void __iomem *port_mmio = mv_ap_base(qc->ap); - struct mv_port_priv *pp = qc->ap->private_data; - unsigned in_index; - u32 in_ptr; + static int limit_warnings = 10; + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + u32 in_index; + unsigned int port_irqs; + + pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY; /* paranoia */ - if (ATA_PROT_DMA != qc->tf.protocol) { - /* We're about to send a non-EDMA capable command to the - * port. Turn off EDMA so there won't be problems accessing - * shadow block, etc registers. + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + if (qc->tf.command == ATA_CMD_DSM) { + if (!ap->ops->bmdma_setup) /* no bmdma on GEN_I */ + return AC_ERR_OTHER; + break; /* use bmdma for this */ + } + /* fall thru */ + case ATA_PROT_NCQ: + mv_start_edma(ap, port_mmio, pp, qc->tf.protocol); + pp->req_idx = (pp->req_idx + 1) & MV_MAX_Q_DEPTH_MASK; + in_index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT; + + /* Write the request in pointer to kick the EDMA to life */ + writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index, + port_mmio + EDMA_REQ_Q_IN_PTR); + return 0; + + case ATA_PROT_PIO: + /* + * Errata SATA#16, SATA#24: warn if multiple DRQs expected. + * + * Someday, we might implement special polling workarounds + * for these, but it all seems rather unnecessary since we + * normally use only DMA for commands which transfer more + * than a single block of data. + * + * Much of the time, this could just work regardless. + * So for now, just log the incident, and allow the attempt. */ - mv_stop_dma(qc->ap); - return ata_qc_issue_prot(qc); + if (limit_warnings > 0 && (qc->nbytes / qc->sect_size) > 1) { + --limit_warnings; + ata_link_warn(qc->dev->link, DRV_NAME + ": attempting PIO w/multiple DRQ: " + "this may fail due to h/w errata\n"); + } + /* drop through */ + case ATA_PROT_NODATA: + case ATAPI_PROT_PIO: + case ATAPI_PROT_NODATA: + if (ap->flags & ATA_FLAG_PIO_POLLING) + qc->tf.flags |= ATA_TFLAG_POLLING; + break; } - in_ptr = readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS); - in_index = (in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + if (qc->tf.flags & ATA_TFLAG_POLLING) + port_irqs = ERR_IRQ; /* mask device interrupt when polling */ + else + port_irqs = ERR_IRQ | DONE_IRQ; /* unmask all interrupts */ - /* until we do queuing, the queue should be empty at this point */ - WARN_ON(in_index != ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) - >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK)); + /* + * We're about to send a non-EDMA capable command to the + * port. Turn off EDMA so there won't be problems accessing + * shadow block, etc registers. + */ + mv_stop_edma(ap); + mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), port_irqs); + mv_pmp_select(ap, qc->dev->link->pmp); + + if (qc->tf.command == ATA_CMD_READ_LOG_EXT) { + struct mv_host_priv *hpriv = ap->host->private_data; + /* + * Workaround for 88SX60x1 FEr SATA#25 (part 2). + * + * After any NCQ error, the READ_LOG_EXT command + * from libata-eh *must* use mv_qc_issue_fis(). + * Otherwise it might fail, due to chip errata. + * + * Rather than special-case it, we'll just *always* + * use this method here for READ_LOG_EXT, making for + * easier testing. + */ + if (IS_GEN_II(hpriv)) + return mv_qc_issue_fis(qc); + } + return ata_bmdma_qc_issue(qc); +} - in_index = mv_inc_q_index(in_index); /* now incr producer index */ +static struct ata_queued_cmd *mv_get_active_qc(struct ata_port *ap) +{ + struct mv_port_priv *pp = ap->private_data; + struct ata_queued_cmd *qc; - mv_start_dma(port_mmio, pp); + if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) + return NULL; + qc = ata_qc_from_tag(ap, ap->link.active_tag); + if (qc && !(qc->tf.flags & ATA_TFLAG_POLLING)) + return qc; + return NULL; +} - /* and write the request in pointer to kick the EDMA to life */ - in_ptr &= EDMA_REQ_Q_BASE_LO_MASK; - in_ptr |= in_index << EDMA_REQ_Q_PTR_SHIFT; - writelfl(in_ptr, port_mmio + EDMA_REQ_Q_IN_PTR_OFS); +static void mv_pmp_error_handler(struct ata_port *ap) +{ + unsigned int pmp, pmp_map; + struct mv_port_priv *pp = ap->private_data; - return 0; + if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) { + /* + * Perform NCQ error analysis on failed PMPs + * before we freeze the port entirely. + * + * The failed PMPs are marked earlier by mv_pmp_eh_prep(). + */ + pmp_map = pp->delayed_eh_pmp_map; + pp->pp_flags &= ~MV_PP_FLAG_DELAYED_EH; + for (pmp = 0; pmp_map != 0; pmp++) { + unsigned int this_pmp = (1 << pmp); + if (pmp_map & this_pmp) { + struct ata_link *link = &ap->pmp_link[pmp]; + pmp_map &= ~this_pmp; + ata_eh_analyze_ncq_error(link); + } + } + ata_port_freeze(ap); + } + sata_pmp_error_handler(ap); } -/** - * mv_get_crpb_status - get status from most recently completed cmd - * @ap: ATA channel to manipulate - * - * This routine is for use when the port is in DMA mode, when it - * will be using the CRPB (command response block) method of - * returning command completion information. We check indices - * are good, grab status, and bump the response consumer index to - * prove that we're up to date. - * - * LOCKING: - * Inherited from caller. - */ -static u8 mv_get_crpb_status(struct ata_port *ap) +static unsigned int mv_get_err_pmp_map(struct ata_port *ap) { void __iomem *port_mmio = mv_ap_base(ap); + + return readl(port_mmio + SATA_TESTCTL) >> 16; +} + +static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map) +{ + struct ata_eh_info *ehi; + unsigned int pmp; + + /* + * Initialize EH info for PMPs which saw device errors + */ + ehi = &ap->link.eh_info; + for (pmp = 0; pmp_map != 0; pmp++) { + unsigned int this_pmp = (1 << pmp); + if (pmp_map & this_pmp) { + struct ata_link *link = &ap->pmp_link[pmp]; + + pmp_map &= ~this_pmp; + ehi = &link->eh_info; + ata_ehi_clear_desc(ehi); + ata_ehi_push_desc(ehi, "dev err"); + ehi->err_mask |= AC_ERR_DEV; + ehi->action |= ATA_EH_RESET; + ata_link_abort(link); + } + } +} + +static int mv_req_q_empty(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 in_ptr, out_ptr; + + in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + return (in_ptr == out_ptr); /* 1 == queue_is_empty */ +} + +static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap) +{ struct mv_port_priv *pp = ap->private_data; - unsigned out_index; - u32 out_ptr; - u8 ata_status; + int failed_links; + unsigned int old_map, new_map; + + /* + * Device error during FBS+NCQ operation: + * + * Set a port flag to prevent further I/O being enqueued. + * Leave the EDMA running to drain outstanding commands from this port. + * Perform the post-mortem/EH only when all responses are complete. + * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.2). + */ + if (!(pp->pp_flags & MV_PP_FLAG_DELAYED_EH)) { + pp->pp_flags |= MV_PP_FLAG_DELAYED_EH; + pp->delayed_eh_pmp_map = 0; + } + old_map = pp->delayed_eh_pmp_map; + new_map = old_map | mv_get_err_pmp_map(ap); - out_ptr = readl(port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); - out_index = (out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + if (old_map != new_map) { + pp->delayed_eh_pmp_map = new_map; + mv_pmp_eh_prep(ap, new_map & ~old_map); + } + failed_links = hweight16(new_map); + + ata_port_info(ap, + "%s: pmp_map=%04x qc_map=%04x failed_links=%d nr_active_links=%d\n", + __func__, pp->delayed_eh_pmp_map, + ap->qc_active, failed_links, + ap->nr_active_links); + + if (ap->nr_active_links <= failed_links && mv_req_q_empty(ap)) { + mv_process_crpb_entries(ap, pp); + mv_stop_edma(ap); + mv_eh_freeze(ap); + ata_port_info(ap, "%s: done\n", __func__); + return 1; /* handled */ + } + ata_port_info(ap, "%s: waiting\n", __func__); + return 1; /* handled */ +} - ata_status = le16_to_cpu(pp->crpb[out_index].flags) - >> CRPB_FLAG_STATUS_SHIFT; +static int mv_handle_fbs_non_ncq_dev_err(struct ata_port *ap) +{ + /* + * Possible future enhancement: + * + * FBS+non-NCQ operation is not yet implemented. + * See related notes in mv_edma_cfg(). + * + * Device error during FBS+non-NCQ operation: + * + * We need to snapshot the shadow registers for each failed command. + * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.3). + */ + return 0; /* not handled */ +} - /* increment our consumer index... */ - out_index = mv_inc_q_index(out_index); +static int mv_handle_dev_err(struct ata_port *ap, u32 edma_err_cause) +{ + struct mv_port_priv *pp = ap->private_data; - /* and, until we do NCQ, there should only be 1 CRPB waiting */ - WARN_ON(out_index != ((readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS) - >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK)); + if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) + return 0; /* EDMA was not active: not handled */ + if (!(pp->pp_flags & MV_PP_FLAG_FBS_EN)) + return 0; /* FBS was not active: not handled */ + + if (!(edma_err_cause & EDMA_ERR_DEV)) + return 0; /* non DEV error: not handled */ + edma_err_cause &= ~EDMA_ERR_IRQ_TRANSIENT; + if (edma_err_cause & ~(EDMA_ERR_DEV | EDMA_ERR_SELF_DIS)) + return 0; /* other problems: not handled */ + + if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) { + /* + * EDMA should NOT have self-disabled for this case. + * If it did, then something is wrong elsewhere, + * and we cannot handle it here. + */ + if (edma_err_cause & EDMA_ERR_SELF_DIS) { + ata_port_warn(ap, "%s: err_cause=0x%x pp_flags=0x%x\n", + __func__, edma_err_cause, pp->pp_flags); + return 0; /* not handled */ + } + return mv_handle_fbs_ncq_dev_err(ap); + } else { + /* + * EDMA should have self-disabled for this case. + * If it did not, then something is wrong elsewhere, + * and we cannot handle it here. + */ + if (!(edma_err_cause & EDMA_ERR_SELF_DIS)) { + ata_port_warn(ap, "%s: err_cause=0x%x pp_flags=0x%x\n", + __func__, edma_err_cause, pp->pp_flags); + return 0; /* not handled */ + } + return mv_handle_fbs_non_ncq_dev_err(ap); + } + return 0; /* not handled */ +} - /* write out our inc'd consumer index so EDMA knows we're caught up */ - out_ptr &= EDMA_RSP_Q_BASE_LO_MASK; - out_ptr |= out_index << EDMA_RSP_Q_PTR_SHIFT; - writelfl(out_ptr, port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); +static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled) +{ + struct ata_eh_info *ehi = &ap->link.eh_info; + char *when = "idle"; - /* Return ATA status register for completed CRPB */ - return ata_status; + ata_ehi_clear_desc(ehi); + if (edma_was_enabled) { + when = "EDMA enabled"; + } else { + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag); + if (qc && (qc->tf.flags & ATA_TFLAG_POLLING)) + when = "polling"; + } + ata_ehi_push_desc(ehi, "unexpected device interrupt while %s", when); + ehi->err_mask |= AC_ERR_OTHER; + ehi->action |= ATA_EH_RESET; + ata_port_freeze(ap); } /** * mv_err_intr - Handle error interrupts on the port * @ap: ATA channel to manipulate - * @reset_allowed: bool: 0 == don't trigger from reset here * - * In most cases, just clear the interrupt and move on. However, - * some cases require an eDMA reset, which is done right before - * the COMRESET in mv_phy_reset(). The SERR case requires a - * clear of pending errors in the SATA SERROR register. Finally, - * if the port disabled DMA, update our cached copy to match. + * Most cases require a full reset of the chip's state machine, + * which also performs a COMRESET. + * Also, if the port disabled DMA, update our cached copy to match. * * LOCKING: * Inherited from caller. */ -static void mv_err_intr(struct ata_port *ap, int reset_allowed) +static void mv_err_intr(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 edma_err_cause, eh_freeze_mask, serr = 0; + u32 fis_cause = 0; + struct mv_port_priv *pp = ap->private_data; + struct mv_host_priv *hpriv = ap->host->private_data; + unsigned int action = 0, err_mask = 0; + struct ata_eh_info *ehi = &ap->link.eh_info; + struct ata_queued_cmd *qc; + int abort = 0; + + /* + * Read and clear the SError and err_cause bits. + * For GenIIe, if EDMA_ERR_TRANS_IRQ_7 is set, we also must read/clear + * the FIS_IRQ_CAUSE register before clearing edma_err_cause. + */ + sata_scr_read(&ap->link, SCR_ERROR, &serr); + sata_scr_write_flush(&ap->link, SCR_ERROR, serr); + + edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE); + if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) { + fis_cause = readl(port_mmio + FIS_IRQ_CAUSE); + writelfl(~fis_cause, port_mmio + FIS_IRQ_CAUSE); + } + writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE); + + if (edma_err_cause & EDMA_ERR_DEV) { + /* + * Device errors during FIS-based switching operation + * require special handling. + */ + if (mv_handle_dev_err(ap, edma_err_cause)) + return; + } + + qc = mv_get_active_qc(ap); + ata_ehi_clear_desc(ehi); + ata_ehi_push_desc(ehi, "edma_err_cause=%08x pp_flags=%08x", + edma_err_cause, pp->pp_flags); + + if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) { + ata_ehi_push_desc(ehi, "fis_cause=%08x", fis_cause); + if (fis_cause & FIS_IRQ_CAUSE_AN) { + u32 ec = edma_err_cause & + ~(EDMA_ERR_TRANS_IRQ_7 | EDMA_ERR_IRQ_TRANSIENT); + sata_async_notification(ap); + if (!ec) + return; /* Just an AN; no need for the nukes */ + ata_ehi_push_desc(ehi, "SDB notify"); + } + } + /* + * All generations share these EDMA error cause bits: + */ + if (edma_err_cause & EDMA_ERR_DEV) { + err_mask |= AC_ERR_DEV; + action |= ATA_EH_RESET; + ata_ehi_push_desc(ehi, "dev error"); + } + if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | + EDMA_ERR_CRQB_PAR | EDMA_ERR_CRPB_PAR | + EDMA_ERR_INTRL_PAR)) { + err_mask |= AC_ERR_ATA_BUS; + action |= ATA_EH_RESET; + ata_ehi_push_desc(ehi, "parity error"); + } + if (edma_err_cause & (EDMA_ERR_DEV_DCON | EDMA_ERR_DEV_CON)) { + ata_ehi_hotplugged(ehi); + ata_ehi_push_desc(ehi, edma_err_cause & EDMA_ERR_DEV_DCON ? + "dev disconnect" : "dev connect"); + action |= ATA_EH_RESET; + } + + /* + * Gen-I has a different SELF_DIS bit, + * different FREEZE bits, and no SERR bit: + */ + if (IS_GEN_I(hpriv)) { + eh_freeze_mask = EDMA_EH_FREEZE_5; + if (edma_err_cause & EDMA_ERR_SELF_DIS_5) { + pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + ata_ehi_push_desc(ehi, "EDMA self-disable"); + } + } else { + eh_freeze_mask = EDMA_EH_FREEZE; + if (edma_err_cause & EDMA_ERR_SELF_DIS) { + pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + ata_ehi_push_desc(ehi, "EDMA self-disable"); + } + if (edma_err_cause & EDMA_ERR_SERR) { + ata_ehi_push_desc(ehi, "SError=%08x", serr); + err_mask |= AC_ERR_ATA_BUS; + action |= ATA_EH_RESET; + } + } + + if (!err_mask) { + err_mask = AC_ERR_OTHER; + action |= ATA_EH_RESET; + } + + ehi->serror |= serr; + ehi->action |= action; + + if (qc) + qc->err_mask |= err_mask; + else + ehi->err_mask |= err_mask; + + if (err_mask == AC_ERR_DEV) { + /* + * Cannot do ata_port_freeze() here, + * because it would kill PIO access, + * which is needed for further diagnosis. + */ + mv_eh_freeze(ap); + abort = 1; + } else if (edma_err_cause & eh_freeze_mask) { + /* + * Note to self: ata_port_freeze() calls ata_port_abort() + */ + ata_port_freeze(ap); + } else { + abort = 1; + } + + if (abort) { + if (qc) + ata_link_abort(qc->dev->link); + else + ata_port_abort(ap); + } +} + +static bool mv_process_crpb_response(struct ata_port *ap, + struct mv_crpb *response, unsigned int tag, int ncq_enabled) +{ + u8 ata_status; + u16 edma_status = le16_to_cpu(response->flags); + + /* + * edma_status from a response queue entry: + * LSB is from EDMA_ERR_IRQ_CAUSE (non-NCQ only). + * MSB is saved ATA status from command completion. + */ + if (!ncq_enabled) { + u8 err_cause = edma_status & 0xff & ~EDMA_ERR_DEV; + if (err_cause) { + /* + * Error will be seen/handled by + * mv_err_intr(). So do nothing at all here. + */ + return false; + } + } + ata_status = edma_status >> CRPB_FLAG_STATUS_SHIFT; + if (!ac_err_mask(ata_status)) + return true; + /* else: leave it for mv_err_intr() */ + return false; +} + +static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp) { void __iomem *port_mmio = mv_ap_base(ap); - u32 edma_err_cause, serr = 0; + struct mv_host_priv *hpriv = ap->host->private_data; + u32 in_index; + bool work_done = false; + u32 done_mask = 0; + int ncq_enabled = (pp->pp_flags & MV_PP_FLAG_NCQ_EN); + + /* Get the hardware queue position index */ + in_index = (readl(port_mmio + EDMA_RSP_Q_IN_PTR) + >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; - edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + /* Process new responses from since the last time we looked */ + while (in_index != pp->resp_idx) { + unsigned int tag; + struct mv_crpb *response = &pp->crpb[pp->resp_idx]; - if (EDMA_ERR_SERR & edma_err_cause) { - sata_scr_read(ap, SCR_ERROR, &serr); - sata_scr_write_flush(ap, SCR_ERROR, serr); + pp->resp_idx = (pp->resp_idx + 1) & MV_MAX_Q_DEPTH_MASK; + + if (IS_GEN_I(hpriv)) { + /* 50xx: no NCQ, only one command active at a time */ + tag = ap->link.active_tag; + } else { + /* Gen II/IIE: get command tag from CRPB entry */ + tag = le16_to_cpu(response->id) & 0x1f; + } + if (mv_process_crpb_response(ap, response, tag, ncq_enabled)) + done_mask |= 1 << tag; + work_done = true; } - if (EDMA_ERR_SELF_DIS & edma_err_cause) { - struct mv_port_priv *pp = ap->private_data; - pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + + if (work_done) { + ata_qc_complete_multiple(ap, ap->qc_active ^ done_mask); + + /* Update the software queue position index in hardware */ + writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | + (pp->resp_idx << EDMA_RSP_Q_PTR_SHIFT), + port_mmio + EDMA_RSP_Q_OUT_PTR); } - DPRINTK(KERN_ERR "ata%u: port error; EDMA err cause: 0x%08x " - "SERR: 0x%08x\n", ap->id, edma_err_cause, serr); +} - /* Clear EDMA now that SERR cleanup done */ - writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); +static void mv_port_intr(struct ata_port *ap, u32 port_cause) +{ + struct mv_port_priv *pp; + int edma_was_enabled; - /* check for fatal here and recover if needed */ - if (reset_allowed && (EDMA_ERR_FATAL & edma_err_cause)) - mv_stop_and_reset(ap); + /* + * Grab a snapshot of the EDMA_EN flag setting, + * so that we have a consistent view for this port, + * even if something we call of our routines changes it. + */ + pp = ap->private_data; + edma_was_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN); + /* + * Process completed CRPB response(s) before other events. + */ + if (edma_was_enabled && (port_cause & DONE_IRQ)) { + mv_process_crpb_entries(ap, pp); + if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) + mv_handle_fbs_ncq_dev_err(ap); + } + /* + * Handle chip-reported errors, or continue on to handle PIO. + */ + if (unlikely(port_cause & ERR_IRQ)) { + mv_err_intr(ap); + } else if (!edma_was_enabled) { + struct ata_queued_cmd *qc = mv_get_active_qc(ap); + if (qc) + ata_bmdma_port_intr(ap, qc); + else + mv_unexpected_intr(ap, edma_was_enabled); + } } /** * mv_host_intr - Handle all interrupts on the given host controller * @host: host specific structure - * @relevant: port error bits relevant to this host controller - * @hc: which host controller we're to look at - * - * Read then write clear the HC interrupt status then walk each - * port connected to the HC and see if it needs servicing. Port - * success ints are reported in the HC interrupt status reg, the - * port error ints are reported in the higher level main - * interrupt status register and thus are passed in via the - * 'relevant' argument. + * @main_irq_cause: Main interrupt cause register for the chip. * * LOCKING: * Inherited from caller. */ -static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc) +static int mv_host_intr(struct ata_host *host, u32 main_irq_cause) { - void __iomem *mmio = host->mmio_base; - void __iomem *hc_mmio = mv_hc_base(mmio, hc); - struct ata_queued_cmd *qc; - u32 hc_irq_cause; - int shift, port, port0, hard_port, handled; - unsigned int err_mask; - - if (hc == 0) { - port0 = 0; - } else { - port0 = MV_PORTS_PER_HC; - } - - /* we'll need the HC success int register in most cases */ - hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS); - if (hc_irq_cause) { - writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS); - } + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base, *hc_mmio; + unsigned int handled = 0, port; - VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n", - hc,relevant,hc_irq_cause); + /* If asserted, clear the "all ports" IRQ coalescing bit */ + if (main_irq_cause & ALL_PORTS_COAL_DONE) + writel(~ALL_PORTS_COAL_IRQ, mmio + IRQ_COAL_CAUSE); - for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) { - u8 ata_status = 0; + for (port = 0; port < hpriv->n_ports; port++) { struct ata_port *ap = host->ports[port]; - struct mv_port_priv *pp = ap->private_data; + unsigned int p, shift, hardport, port_cause; - hard_port = mv_hardport_from_port(port); /* range 0..3 */ - handled = 0; /* ensure ata_status is set if handled++ */ - - /* Note that DEV_IRQ might happen spuriously during EDMA, - * and should be ignored in such cases. - * The cause of this is still under investigation. + MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport); + /* + * Each hc within the host has its own hc_irq_cause register, + * where the interrupting ports bits get ack'd. */ - if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) { - /* EDMA: check for response queue interrupt */ - if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause) { - ata_status = mv_get_crpb_status(ap); - handled = 1; + if (hardport == 0) { /* first port on this hc ? */ + u32 hc_cause = (main_irq_cause >> shift) & HC0_IRQ_PEND; + u32 port_mask, ack_irqs; + /* + * Skip this entire hc if nothing pending for any ports + */ + if (!hc_cause) { + port += MV_PORTS_PER_HC - 1; + continue; } - } else { - /* PIO: check for device (drive) interrupt */ - if ((DEV_IRQ << hard_port) & hc_irq_cause) { - ata_status = readb((void __iomem *) - ap->ioaddr.status_addr); - handled = 1; - /* ignore spurious intr if drive still BUSY */ - if (ata_status & ATA_BUSY) { - ata_status = 0; - handled = 0; - } + /* + * We don't need/want to read the hc_irq_cause register, + * because doing so hurts performance, and + * main_irq_cause already gives us everything we need. + * + * But we do have to *write* to the hc_irq_cause to ack + * the ports that we are handling this time through. + * + * This requires that we create a bitmap for those + * ports which interrupted us, and use that bitmap + * to ack (only) those ports via hc_irq_cause. + */ + ack_irqs = 0; + if (hc_cause & PORTS_0_3_COAL_DONE) + ack_irqs = HC_COAL_IRQ; + for (p = 0; p < MV_PORTS_PER_HC; ++p) { + if ((port + p) >= hpriv->n_ports) + break; + port_mask = (DONE_IRQ | ERR_IRQ) << (p * 2); + if (hc_cause & port_mask) + ack_irqs |= (DMA_IRQ | DEV_IRQ) << p; } - } - - if (ap && (ap->flags & ATA_FLAG_DISABLED)) - continue; - - err_mask = ac_err_mask(ata_status); - - shift = port << 1; /* (port * 2) */ - if (port >= MV_PORTS_PER_HC) { - shift++; /* skip bit 8 in the HC Main IRQ reg */ - } - if ((PORT0_ERR << shift) & relevant) { - mv_err_intr(ap, 1); - err_mask |= AC_ERR_OTHER; + hc_mmio = mv_hc_base_from_port(mmio, port); + writelfl(~ack_irqs, hc_mmio + HC_IRQ_CAUSE); handled = 1; } + /* + * Handle interrupts signalled for this port: + */ + port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ); + if (port_cause) + mv_port_intr(ap, port_cause); + } + return handled; +} - if (handled) { - qc = ata_qc_from_tag(ap, ap->active_tag); - if (qc && (qc->flags & ATA_QCFLAG_ACTIVE)) { - VPRINTK("port %u IRQ found for qc, " - "ata_status 0x%x\n", port,ata_status); - /* mark qc status appropriately */ - if (!(qc->tf.flags & ATA_TFLAG_POLLING)) { - qc->err_mask |= err_mask; - ata_qc_complete(qc); - } - } +static int mv_pci_error(struct ata_host *host, void __iomem *mmio) +{ + struct mv_host_priv *hpriv = host->private_data; + struct ata_port *ap; + struct ata_queued_cmd *qc; + struct ata_eh_info *ehi; + unsigned int i, err_mask, printed = 0; + u32 err_cause; + + err_cause = readl(mmio + hpriv->irq_cause_offset); + + dev_err(host->dev, "PCI ERROR; PCI IRQ cause=0x%08x\n", err_cause); + + DPRINTK("All regs @ PCI error\n"); + mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev)); + + writelfl(0, mmio + hpriv->irq_cause_offset); + + for (i = 0; i < host->n_ports; i++) { + ap = host->ports[i]; + if (!ata_link_offline(&ap->link)) { + ehi = &ap->link.eh_info; + ata_ehi_clear_desc(ehi); + if (!printed++) + ata_ehi_push_desc(ehi, + "PCI err cause 0x%08x", err_cause); + err_mask = AC_ERR_HOST_BUS; + ehi->action = ATA_EH_RESET; + qc = ata_qc_from_tag(ap, ap->link.active_tag); + if (qc) + qc->err_mask |= err_mask; + else + ehi->err_mask |= err_mask; + + ata_port_freeze(ap); } } - VPRINTK("EXIT\n"); + return 1; /* handled */ } /** - * mv_interrupt - + * mv_interrupt - Main interrupt event handler * @irq: unused * @dev_instance: private data; in this case the host structure - * @regs: unused * * Read the read only register to determine if any host * controllers have pending interrupts. If so, call lower level @@ -1447,68 +3002,42 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc) * This routine holds the host lock while processing pending * interrupts. */ -static irqreturn_t mv_interrupt(int irq, void *dev_instance, - struct pt_regs *regs) +static irqreturn_t mv_interrupt(int irq, void *dev_instance) { struct ata_host *host = dev_instance; - unsigned int hc, handled = 0, n_hcs; - void __iomem *mmio = host->mmio_base; - struct mv_host_priv *hpriv; - u32 irq_stat; - - irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS); - - /* check the cases where we either have nothing pending or have read - * a bogus register value which can indicate HW removal or PCI fault - */ - if (!irq_stat || (0xffffffffU == irq_stat)) { - return IRQ_NONE; - } + struct mv_host_priv *hpriv = host->private_data; + unsigned int handled = 0; + int using_msi = hpriv->hp_flags & MV_HP_FLAG_MSI; + u32 main_irq_cause, pending_irqs; - n_hcs = mv_get_hc_count(host->ports[0]->flags); spin_lock(&host->lock); - for (hc = 0; hc < n_hcs; hc++) { - u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT)); - if (relevant) { - mv_host_intr(host, relevant, hc); - handled++; - } - } + /* for MSI: block new interrupts while in here */ + if (using_msi) + mv_write_main_irq_mask(0, hpriv); - hpriv = host->private_data; - if (IS_60XX(hpriv)) { - /* deal with the interrupt coalescing bits */ - if (irq_stat & (TRAN_LO_DONE | TRAN_HI_DONE | PORTS_0_7_COAL_DONE)) { - writelfl(0, mmio + MV_IRQ_COAL_CAUSE_LO); - writelfl(0, mmio + MV_IRQ_COAL_CAUSE_HI); - writelfl(0, mmio + MV_IRQ_COAL_CAUSE); - } + main_irq_cause = readl(hpriv->main_irq_cause_addr); + pending_irqs = main_irq_cause & hpriv->main_irq_mask; + /* + * Deal with cases where we either have nothing pending, or have read + * a bogus register value which can indicate HW removal or PCI fault. + */ + if (pending_irqs && main_irq_cause != 0xffffffffU) { + if (unlikely((pending_irqs & PCI_ERR) && !IS_SOC(hpriv))) + handled = mv_pci_error(host, hpriv->base); + else + handled = mv_host_intr(host, pending_irqs); } - if (PCI_ERR & irq_stat) { - printk(KERN_ERR DRV_NAME ": PCI ERROR; PCI IRQ cause=0x%08x\n", - readl(mmio + PCI_IRQ_CAUSE_OFS)); + /* for MSI: unmask; interrupt cause bits will retrigger now */ + if (using_msi) + mv_write_main_irq_mask(hpriv->main_irq_mask, hpriv); - DPRINTK("All regs @ PCI error\n"); - mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev)); - - writelfl(0, mmio + PCI_IRQ_CAUSE_OFS); - handled++; - } spin_unlock(&host->lock); return IRQ_RETVAL(handled); } -static void __iomem *mv5_phy_base(void __iomem *mmio, unsigned int port) -{ - void __iomem *hc_mmio = mv_hc_base_from_port(mmio, port); - unsigned long ofs = (mv_hardport_from_port(port) + 1) * 0x100UL; - - return hc_mmio + ofs; -} - static unsigned int mv5_scr_offset(unsigned int sc_reg_in) { unsigned int ofs; @@ -1526,34 +3055,40 @@ static unsigned int mv5_scr_offset(unsigned int sc_reg_in) return ofs; } -static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in) +static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val) { - void __iomem *mmio = mv5_phy_base(ap->host->mmio_base, ap->port_no); + struct mv_host_priv *hpriv = link->ap->host->private_data; + void __iomem *mmio = hpriv->base; + void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no); unsigned int ofs = mv5_scr_offset(sc_reg_in); - if (ofs != 0xffffffffU) - return readl(mmio + ofs); - else - return (u32) ofs; + if (ofs != 0xffffffffU) { + *val = readl(addr + ofs); + return 0; + } else + return -EINVAL; } -static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) +static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val) { - void __iomem *mmio = mv5_phy_base(ap->host->mmio_base, ap->port_no); + struct mv_host_priv *hpriv = link->ap->host->private_data; + void __iomem *mmio = hpriv->base; + void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no); unsigned int ofs = mv5_scr_offset(sc_reg_in); - if (ofs != 0xffffffffU) - writelfl(val, mmio + ofs); + if (ofs != 0xffffffffU) { + writelfl(val, addr + ofs); + return 0; + } else + return -EINVAL; } -static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio) +static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio) { - u8 rev_id; + struct pci_dev *pdev = to_pci_dev(host->dev); int early_5080; - pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id); - - early_5080 = (pdev->device == 0x5080) && (rev_id == 0); + early_5080 = (pdev->device == 0x5080) && (pdev->revision == 0); if (!early_5080) { u32 tmp = readl(mmio + MV_PCI_EXP_ROM_BAR_CTL); @@ -1561,12 +3096,12 @@ static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio) writel(tmp, mmio + MV_PCI_EXP_ROM_BAR_CTL); } - mv_reset_pci_bus(pdev, mmio); + mv_reset_pci_bus(host, mmio); } static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) { - writel(0x0fcfffff, mmio + MV_FLASH_CTL); + writel(0x0fcfffff, mmio + FLASH_CTL); } static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx, @@ -1585,7 +3120,7 @@ static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) { u32 tmp; - writel(0, mmio + MV_GPIO_PORT_CTL); + writel(0, mmio + GPIO_PORT_CTL); /* FIXME: handle MV_HP_ERRATA_50XXB2 errata */ @@ -1603,9 +3138,9 @@ static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0); if (fix_apm_sq) { - tmp = readl(phy_mmio + MV5_LT_MODE); + tmp = readl(phy_mmio + MV5_LTMODE); tmp |= (1 << 19); - writel(tmp, phy_mmio + MV5_LT_MODE); + writel(tmp, phy_mmio + MV5_LTMODE); tmp = readl(phy_mmio + MV5_PHY_CTL); tmp &= ~0x3; @@ -1628,12 +3163,10 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio, { void __iomem *port_mmio = mv_port_base(mmio, port); - writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS); - - mv_channel_reset(hpriv, mmio, port); + mv_reset_channel(hpriv, mmio, port); ZERO(0x028); /* command */ - writel(0x11f, port_mmio + EDMA_CFG_OFS); + writel(0x11f, port_mmio + EDMA_CFG); ZERO(0x004); /* timer */ ZERO(0x008); /* irq err cause */ ZERO(0x00c); /* irq err mask */ @@ -1685,8 +3218,9 @@ static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, #undef ZERO #define ZERO(reg) writel(0, mmio + (reg)) -static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) +static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio) { + struct mv_host_priv *hpriv = host->private_data; u32 tmp; tmp = readl(mmio + MV_PCI_MODE); @@ -1696,10 +3230,9 @@ static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) ZERO(MV_PCI_DISC_TIMER); ZERO(MV_PCI_MSI_TRIGGER); writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); - ZERO(HC_MAIN_IRQ_MASK_OFS); ZERO(MV_PCI_SERR_MASK); - ZERO(PCI_IRQ_CAUSE_OFS); - ZERO(PCI_IRQ_MASK_OFS); + ZERO(hpriv->irq_cause_offset); + ZERO(hpriv->irq_mask_offset); ZERO(MV_PCI_ERR_LOW_ADDRESS); ZERO(MV_PCI_ERR_HIGH_ADDRESS); ZERO(MV_PCI_ERR_ATTRIBUTE); @@ -1713,10 +3246,10 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) mv5_reset_flash(hpriv, mmio); - tmp = readl(mmio + MV_GPIO_PORT_CTL); + tmp = readl(mmio + GPIO_PORT_CTL); tmp &= 0x3; tmp |= (1 << 5) | (1 << 6); - writel(tmp, mmio + MV_GPIO_PORT_CTL); + writel(tmp, mmio + GPIO_PORT_CTL); } /** @@ -1731,7 +3264,7 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int n_hc) { - void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS; + void __iomem *reg = mmio + PCI_MAIN_CMD_STS; int i, rc = 0; u32 t; @@ -1744,9 +3277,8 @@ static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, for (i = 0; i < 1000; i++) { udelay(1); t = readl(reg); - if (PCI_MASTER_EMPTY & t) { + if (PCI_MASTER_EMPTY & t) break; - } } if (!(PCI_MASTER_EMPTY & t)) { printk(KERN_ERR DRV_NAME ": PCI master won't flush\n"); @@ -1790,7 +3322,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, void __iomem *port_mmio; u32 tmp; - tmp = readl(mmio + MV_RESET_CFG); + tmp = readl(mmio + RESET_CFG); if ((tmp & (1 << 0)) == 0) { hpriv->signal[idx].amps = 0x7 << 8; hpriv->signal[idx].pre = 0x1 << 5; @@ -1806,7 +3338,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) { - writel(0x00000060, mmio + MV_GPIO_PORT_CTL); + writel(0x00000060, mmio + GPIO_PORT_CTL); } static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, @@ -1819,7 +3351,7 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); int fix_phy_mode4 = hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); - u32 m2, tmp; + u32 m2, m3; if (fix_phy_mode2) { m2 = readl(port_mmio + PHY_MODE2); @@ -1836,27 +3368,37 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, udelay(200); } - /* who knows what this magic does */ - tmp = readl(port_mmio + PHY_MODE3); - tmp &= ~0x7F800000; - tmp |= 0x2A800000; - writel(tmp, port_mmio + PHY_MODE3); - - if (fix_phy_mode4) { - u32 m4; - - m4 = readl(port_mmio + PHY_MODE4); - - if (hp_flags & MV_HP_ERRATA_60X1B2) - tmp = readl(port_mmio + 0x310); + /* + * Gen-II/IIe PHY_MODE3 errata RM#2: + * Achieves better receiver noise performance than the h/w default: + */ + m3 = readl(port_mmio + PHY_MODE3); + m3 = (m3 & 0x1f) | (0x5555601 << 5); - m4 = (m4 & ~(1 << 1)) | (1 << 0); + /* Guideline 88F5182 (GL# SATA-S11) */ + if (IS_SOC(hpriv)) + m3 &= ~0x1c; + if (fix_phy_mode4) { + u32 m4 = readl(port_mmio + PHY_MODE4); + /* + * Enforce reserved-bit restrictions on GenIIe devices only. + * For earlier chipsets, force only the internal config field + * (workaround for errata FEr SATA#10 part 1). + */ + if (IS_GEN_IIE(hpriv)) + m4 = (m4 & ~PHY_MODE4_RSVD_ZEROS) | PHY_MODE4_RSVD_ONES; + else + m4 = (m4 & ~PHY_MODE4_CFG_MASK) | PHY_MODE4_CFG_VALUE; writel(m4, port_mmio + PHY_MODE4); - - if (hp_flags & MV_HP_ERRATA_60X1B2) - writel(tmp, port_mmio + 0x310); } + /* + * Workaround for 60x1-B2 errata SATA#13: + * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3, + * so we must always rewrite PHY_MODE3 after PHY_MODE4. + * Or ensure we use writelfl() when writing PHY_MODE4. + */ + writel(m3, port_mmio + PHY_MODE3); /* Revert values of pre-emphasis and signal amps to the saved ones */ m2 = readl(port_mmio + PHY_MODE2); @@ -1875,191 +3417,271 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, writel(m2, port_mmio + PHY_MODE2); } -static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio, - unsigned int port_no) +/* TODO: use the generic LED interface to configure the SATA Presence */ +/* & Acitivy LEDs on the board */ +static void mv_soc_enable_leds(struct mv_host_priv *hpriv, + void __iomem *mmio) { - void __iomem *port_mmio = mv_port_base(mmio, port_no); + return; +} - writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS); +static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio) +{ + void __iomem *port_mmio; + u32 tmp; - if (IS_60XX(hpriv)) { - u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL); - ifctl |= (1 << 7); /* enable gen2i speed */ - ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */ - writelfl(ifctl, port_mmio + SATA_INTERFACE_CTL); - } + port_mmio = mv_port_base(mmio, idx); + tmp = readl(port_mmio + PHY_MODE2); - udelay(25); /* allow reset propagation */ + hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */ + hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */ +} - /* Spec never mentions clearing the bit. Marvell's driver does - * clear the bit, however. - */ - writelfl(0, port_mmio + EDMA_CMD_OFS); +#undef ZERO +#define ZERO(reg) writel(0, port_mmio + (reg)) +static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int port) +{ + void __iomem *port_mmio = mv_port_base(mmio, port); - hpriv->ops->phy_errata(hpriv, mmio, port_no); + mv_reset_channel(hpriv, mmio, port); + + ZERO(0x028); /* command */ + writel(0x101f, port_mmio + EDMA_CFG); + ZERO(0x004); /* timer */ + ZERO(0x008); /* irq err cause */ + ZERO(0x00c); /* irq err mask */ + ZERO(0x010); /* rq bah */ + ZERO(0x014); /* rq inp */ + ZERO(0x018); /* rq outp */ + ZERO(0x01c); /* respq bah */ + ZERO(0x024); /* respq outp */ + ZERO(0x020); /* respq inp */ + ZERO(0x02c); /* test control */ + writel(0x800, port_mmio + EDMA_IORDY_TMOUT); +} + +#undef ZERO + +#define ZERO(reg) writel(0, hc_mmio + (reg)) +static void mv_soc_reset_one_hc(struct mv_host_priv *hpriv, + void __iomem *mmio) +{ + void __iomem *hc_mmio = mv_hc_base(mmio, 0); + + ZERO(0x00c); + ZERO(0x010); + ZERO(0x014); - if (IS_50XX(hpriv)) - mdelay(1); } -static void mv_stop_and_reset(struct ata_port *ap) +#undef ZERO + +static int mv_soc_reset_hc(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int n_hc) { - struct mv_host_priv *hpriv = ap->host->private_data; - void __iomem *mmio = ap->host->mmio_base; + unsigned int port; - mv_stop_dma(ap); + for (port = 0; port < hpriv->n_ports; port++) + mv_soc_reset_hc_port(hpriv, mmio, port); - mv_channel_reset(hpriv, mmio, ap->port_no); + mv_soc_reset_one_hc(hpriv, mmio); - __mv_phy_reset(ap, 0); + return 0; } -static inline void __msleep(unsigned int msec, int can_sleep) +static void mv_soc_reset_flash(struct mv_host_priv *hpriv, + void __iomem *mmio) { - if (can_sleep) - msleep(msec); - else - mdelay(msec); + return; +} + +static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio) +{ + return; +} + +static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int port) +{ + void __iomem *port_mmio = mv_port_base(mmio, port); + u32 reg; + + reg = readl(port_mmio + PHY_MODE3); + reg &= ~(0x3 << 27); /* SELMUPF (bits 28:27) to 1 */ + reg |= (0x1 << 27); + reg &= ~(0x3 << 29); /* SELMUPI (bits 30:29) to 1 */ + reg |= (0x1 << 29); + writel(reg, port_mmio + PHY_MODE3); + + reg = readl(port_mmio + PHY_MODE4); + reg &= ~0x1; /* SATU_OD8 (bit 0) to 0, reserved bit 16 must be set */ + reg |= (0x1 << 16); + writel(reg, port_mmio + PHY_MODE4); + + reg = readl(port_mmio + PHY_MODE9_GEN2); + reg &= ~0xf; /* TXAMP[3:0] (bits 3:0) to 8 */ + reg |= 0x8; + reg &= ~(0x1 << 14); /* TXAMP[4] (bit 14) to 0 */ + writel(reg, port_mmio + PHY_MODE9_GEN2); + + reg = readl(port_mmio + PHY_MODE9_GEN1); + reg &= ~0xf; /* TXAMP[3:0] (bits 3:0) to 8 */ + reg |= 0x8; + reg &= ~(0x1 << 14); /* TXAMP[4] (bit 14) to 0 */ + writel(reg, port_mmio + PHY_MODE9_GEN1); } /** - * __mv_phy_reset - Perform eDMA reset followed by COMRESET - * @ap: ATA channel to manipulate - * - * Part of this is taken from __sata_phy_reset and modified to - * not sleep since this routine gets called from interrupt level. + * soc_is_65 - check if the soc is 65 nano device * - * LOCKING: - * Inherited from caller. This is coded to safe to call at - * interrupt level, i.e. it does not sleep. + * Detect the type of the SoC, this is done by reading the PHYCFG_OFS + * register, this register should contain non-zero value and it exists only + * in the 65 nano devices, when reading it from older devices we get 0. */ -static void __mv_phy_reset(struct ata_port *ap, int can_sleep) +static bool soc_is_65n(struct mv_host_priv *hpriv) { - struct mv_port_priv *pp = ap->private_data; - struct mv_host_priv *hpriv = ap->host->private_data; - void __iomem *port_mmio = mv_ap_base(ap); - struct ata_taskfile tf; - struct ata_device *dev = &ap->device[0]; - unsigned long timeout; - int retry = 5; - u32 sstatus; + void __iomem *port0_mmio = mv_port_base(hpriv->base, 0); - VPRINTK("ENTER, port %u, mmio 0x%p\n", ap->port_no, port_mmio); - - DPRINTK("S-regs after ATA_RST: SStat 0x%08x SErr 0x%08x " - "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS), - mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL)); + if (readl(port0_mmio + PHYCFG_OFS)) + return true; + return false; +} - /* Issue COMRESET via SControl */ -comreset_retry: - sata_scr_write_flush(ap, SCR_CONTROL, 0x301); - __msleep(1, can_sleep); +static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i) +{ + u32 ifcfg = readl(port_mmio + SATA_IFCFG); - sata_scr_write_flush(ap, SCR_CONTROL, 0x300); - __msleep(20, can_sleep); + ifcfg = (ifcfg & 0xf7f) | 0x9b1000; /* from chip spec */ + if (want_gen2i) + ifcfg |= (1 << 7); /* enable gen2i speed */ + writelfl(ifcfg, port_mmio + SATA_IFCFG); +} - timeout = jiffies + msecs_to_jiffies(200); - do { - sata_scr_read(ap, SCR_STATUS, &sstatus); - if (((sstatus & 0x3) == 3) || ((sstatus & 0x3) == 0)) - break; +static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port_no) +{ + void __iomem *port_mmio = mv_port_base(mmio, port_no); - __msleep(1, can_sleep); - } while (time_before(jiffies, timeout)); + /* + * The datasheet warns against setting EDMA_RESET when EDMA is active + * (but doesn't say what the problem might be). So we first try + * to disable the EDMA engine before doing the EDMA_RESET operation. + */ + mv_stop_edma_engine(port_mmio); + writelfl(EDMA_RESET, port_mmio + EDMA_CMD); - /* work around errata */ - if (IS_60XX(hpriv) && - (sstatus != 0x0) && (sstatus != 0x113) && (sstatus != 0x123) && - (retry-- > 0)) - goto comreset_retry; + if (!IS_GEN_I(hpriv)) { + /* Enable 3.0gb/s link speed: this survives EDMA_RESET */ + mv_setup_ifcfg(port_mmio, 1); + } + /* + * Strobing EDMA_RESET here causes a hard reset of the SATA transport, + * link, and physical layers. It resets all SATA interface registers + * (except for SATA_IFCFG), and issues a COMRESET to the dev. + */ + writelfl(EDMA_RESET, port_mmio + EDMA_CMD); + udelay(25); /* allow reset propagation */ + writelfl(0, port_mmio + EDMA_CMD); - DPRINTK("S-regs after PHY wake: SStat 0x%08x SErr 0x%08x " - "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS), - mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL)); + hpriv->ops->phy_errata(hpriv, mmio, port_no); - if (ata_port_online(ap)) { - ata_port_probe(ap); - } else { - sata_scr_read(ap, SCR_STATUS, &sstatus); - ata_port_printk(ap, KERN_INFO, - "no device found (phy stat %08x)\n", sstatus); - ata_port_disable(ap); - return; - } - ap->cbl = ATA_CBL_SATA; + if (IS_GEN_I(hpriv)) + mdelay(1); +} - /* even after SStatus reflects that device is ready, - * it seems to take a while for link to be fully - * established (and thus Status no longer 0x80/0x7F), - * so we poll a bit for that, here. - */ - retry = 20; - while (1) { - u8 drv_stat = ata_check_status(ap); - if ((drv_stat != 0x80) && (drv_stat != 0x7f)) - break; - __msleep(500, can_sleep); - if (retry-- <= 0) - break; +static void mv_pmp_select(struct ata_port *ap, int pmp) +{ + if (sata_pmp_supported(ap)) { + void __iomem *port_mmio = mv_ap_base(ap); + u32 reg = readl(port_mmio + SATA_IFCTL); + int old = reg & 0xf; + + if (old != pmp) { + reg = (reg & ~0xf) | pmp; + writelfl(reg, port_mmio + SATA_IFCTL); + } } +} - tf.lbah = readb((void __iomem *) ap->ioaddr.lbah_addr); - tf.lbam = readb((void __iomem *) ap->ioaddr.lbam_addr); - tf.lbal = readb((void __iomem *) ap->ioaddr.lbal_addr); - tf.nsect = readb((void __iomem *) ap->ioaddr.nsect_addr); +static int mv_pmp_hardreset(struct ata_link *link, unsigned int *class, + unsigned long deadline) +{ + mv_pmp_select(link->ap, sata_srst_pmp(link)); + return sata_std_hardreset(link, class, deadline); +} - dev->class = ata_dev_classify(&tf); - if (!ata_dev_enabled(dev)) { - VPRINTK("Port disabled post-sig: No device present.\n"); - ata_port_disable(ap); - } +static int mv_softreset(struct ata_link *link, unsigned int *class, + unsigned long deadline) +{ + mv_pmp_select(link->ap, sata_srst_pmp(link)); + return ata_sff_softreset(link, class, deadline); +} - writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); +static int mv_hardreset(struct ata_link *link, unsigned int *class, + unsigned long deadline) +{ + struct ata_port *ap = link->ap; + struct mv_host_priv *hpriv = ap->host->private_data; + struct mv_port_priv *pp = ap->private_data; + void __iomem *mmio = hpriv->base; + int rc, attempts = 0, extra = 0; + u32 sstatus; + bool online; + mv_reset_channel(hpriv, mmio, ap->port_no); pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + pp->pp_flags &= + ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY); - VPRINTK("EXIT\n"); + /* Workaround for errata FEr SATA#10 (part 2) */ + do { + const unsigned long *timing = + sata_ehc_deb_timing(&link->eh_context); + + rc = sata_link_hardreset(link, timing, deadline + extra, + &online, NULL); + rc = online ? -EAGAIN : rc; + if (rc) + return rc; + sata_scr_read(link, SCR_STATUS, &sstatus); + if (!IS_GEN_I(hpriv) && ++attempts >= 5 && sstatus == 0x121) { + /* Force 1.5gb/s link speed and try again */ + mv_setup_ifcfg(mv_ap_base(ap), 0); + if (time_after(jiffies + HZ, deadline)) + extra = HZ; /* only extend it once, max */ + } + } while (sstatus != 0x0 && sstatus != 0x113 && sstatus != 0x123); + mv_save_cached_regs(ap); + mv_edma_cfg(ap, 0, 0); + + return rc; } -static void mv_phy_reset(struct ata_port *ap) +static void mv_eh_freeze(struct ata_port *ap) { - __mv_phy_reset(ap, 1); + mv_stop_edma(ap); + mv_enable_port_irqs(ap, 0); } -/** - * mv_eng_timeout - Routine called by libata when SCSI times out I/O - * @ap: ATA channel to manipulate - * - * Intent is to clear all pending error conditions, reset the - * chip/bus, fail the command, and move on. - * - * LOCKING: - * This routine holds the host lock while failing the command. - */ -static void mv_eng_timeout(struct ata_port *ap) +static void mv_eh_thaw(struct ata_port *ap) { - struct ata_queued_cmd *qc; - unsigned long flags; - - ata_port_printk(ap, KERN_ERR, "Entering mv_eng_timeout\n"); - DPRINTK("All regs @ start of eng_timeout\n"); - mv_dump_all_regs(ap->host->mmio_base, ap->port_no, - to_pci_dev(ap->host->dev)); + struct mv_host_priv *hpriv = ap->host->private_data; + unsigned int port = ap->port_no; + unsigned int hardport = mv_hardport_from_port(port); + void __iomem *hc_mmio = mv_hc_base_from_port(hpriv->base, port); + void __iomem *port_mmio = mv_ap_base(ap); + u32 hc_irq_cause; - qc = ata_qc_from_tag(ap, ap->active_tag); - printk(KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n", - ap->host->mmio_base, ap, qc, qc->scsicmd, &qc->scsicmd->cmnd); + /* clear EDMA errors on this port */ + writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE); - spin_lock_irqsave(&ap->host->lock, flags); - mv_err_intr(ap, 0); - mv_stop_and_reset(ap); - spin_unlock_irqrestore(&ap->host->lock, flags); + /* clear pending irq events */ + hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport); + writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE); - WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE)); - if (qc->flags & ATA_QCFLAG_ACTIVE) { - qc->err_mask |= AC_ERR_TIMEOUT; - ata_eh_qc_complete(qc); - } + mv_enable_port_irqs(ap, ERR_IRQ); } /** @@ -2076,8 +3698,7 @@ static void mv_eng_timeout(struct ata_port *ap) */ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio) { - unsigned long shd_base = (unsigned long) port_mmio + SHD_BLK_OFS; - unsigned serr_ofs; + void __iomem *serr, *shd_base = port_mmio + SHD_BLK; /* PIO related setup */ @@ -2092,39 +3713,74 @@ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio) port->status_addr = port->command_addr = shd_base + (sizeof(u32) * ATA_REG_STATUS); /* special case: control/altstatus doesn't have ATA_REG_ address */ - port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST_OFS; - - /* unused: */ - port->cmd_addr = port->bmdma_addr = port->scr_addr = 0; + port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST; /* Clear any currently outstanding port interrupt conditions */ - serr_ofs = mv_scr_offset(SCR_ERROR); - writelfl(readl(port_mmio + serr_ofs), port_mmio + serr_ofs); - writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + serr = port_mmio + mv_scr_offset(SCR_ERROR); + writelfl(readl(serr), serr); + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE); - /* unmask all EDMA error interrupts */ - writelfl(~0, port_mmio + EDMA_ERR_IRQ_MASK_OFS); + /* unmask all non-transient EDMA error interrupts */ + writelfl(~EDMA_ERR_IRQ_TRANSIENT, port_mmio + EDMA_ERR_IRQ_MASK); VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n", - readl(port_mmio + EDMA_CFG_OFS), - readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS), - readl(port_mmio + EDMA_ERR_IRQ_MASK_OFS)); + readl(port_mmio + EDMA_CFG), + readl(port_mmio + EDMA_ERR_IRQ_CAUSE), + readl(port_mmio + EDMA_ERR_IRQ_MASK)); } -static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, - unsigned int board_idx) +static unsigned int mv_in_pcix_mode(struct ata_host *host) { - u8 rev_id; - u32 hp_flags = hpriv->hp_flags; + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; + u32 reg; + + if (IS_SOC(hpriv) || !IS_PCIE(hpriv)) + return 0; /* not PCI-X capable */ + reg = readl(mmio + MV_PCI_MODE); + if ((reg & MV_PCI_MODE_MASK) == 0) + return 0; /* conventional PCI mode */ + return 1; /* chip is in PCI-X mode */ +} + +static int mv_pci_cut_through_okay(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; + u32 reg; - pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id); + if (!mv_in_pcix_mode(host)) { + reg = readl(mmio + MV_PCI_COMMAND); + if (reg & MV_PCI_COMMAND_MRDTRIG) + return 0; /* not okay */ + } + return 1; /* okay */ +} + +static void mv_60x1b2_errata_pci7(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; + + /* workaround for 60x1-B2 errata PCI#7 */ + if (mv_in_pcix_mode(host)) { + u32 reg = readl(mmio + MV_PCI_COMMAND); + writelfl(reg & ~MV_PCI_COMMAND_MWRCOM, mmio + MV_PCI_COMMAND); + } +} - switch(board_idx) { +static int mv_chip_id(struct ata_host *host, unsigned int board_idx) +{ + struct pci_dev *pdev = to_pci_dev(host->dev); + struct mv_host_priv *hpriv = host->private_data; + u32 hp_flags = hpriv->hp_flags; + + switch (board_idx) { case chip_5080: hpriv->ops = &mv5xxx_ops; - hp_flags |= MV_HP_50XX; + hp_flags |= MV_HP_GEN_I; - switch (rev_id) { + switch (pdev->revision) { case 0x1: hp_flags |= MV_HP_ERRATA_50XXB0; break; @@ -2132,8 +3788,8 @@ static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, hp_flags |= MV_HP_ERRATA_50XXB2; break; default: - dev_printk(KERN_WARNING, &pdev->dev, - "Applying 50XXB2 workarounds to unknown rev\n"); + dev_warn(&pdev->dev, + "Applying 50XXB2 workarounds to unknown rev\n"); hp_flags |= MV_HP_ERRATA_50XXB2; break; } @@ -2142,9 +3798,9 @@ static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, case chip_504x: case chip_508x: hpriv->ops = &mv5xxx_ops; - hp_flags |= MV_HP_50XX; + hp_flags |= MV_HP_GEN_I; - switch (rev_id) { + switch (pdev->revision) { case 0x0: hp_flags |= MV_HP_ERRATA_50XXB0; break; @@ -2152,8 +3808,8 @@ static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, hp_flags |= MV_HP_ERRATA_50XXB2; break; default: - dev_printk(KERN_WARNING, &pdev->dev, - "Applying B2 workarounds to unknown rev\n"); + dev_warn(&pdev->dev, + "Applying B2 workarounds to unknown rev\n"); hp_flags |= MV_HP_ERRATA_50XXB2; break; } @@ -2162,57 +3818,104 @@ static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, case chip_604x: case chip_608x: hpriv->ops = &mv6xxx_ops; + hp_flags |= MV_HP_GEN_II; - switch (rev_id) { + switch (pdev->revision) { case 0x7: + mv_60x1b2_errata_pci7(host); hp_flags |= MV_HP_ERRATA_60X1B2; break; case 0x9: hp_flags |= MV_HP_ERRATA_60X1C0; break; default: - dev_printk(KERN_WARNING, &pdev->dev, - "Applying B2 workarounds to unknown rev\n"); + dev_warn(&pdev->dev, + "Applying B2 workarounds to unknown rev\n"); hp_flags |= MV_HP_ERRATA_60X1B2; break; } break; case chip_7042: + hp_flags |= MV_HP_PCIE | MV_HP_CUT_THROUGH; + if (pdev->vendor == PCI_VENDOR_ID_TTI && + (pdev->device == 0x2300 || pdev->device == 0x2310)) + { + /* + * Highpoint RocketRAID PCIe 23xx series cards: + * + * Unconfigured drives are treated as "Legacy" + * by the BIOS, and it overwrites sector 8 with + * a "Lgcy" metadata block prior to Linux boot. + * + * Configured drives (RAID or JBOD) leave sector 8 + * alone, but instead overwrite a high numbered + * sector for the RAID metadata. This sector can + * be determined exactly, by truncating the physical + * drive capacity to a nice even GB value. + * + * RAID metadata is at: (dev->n_sectors & ~0xfffff) + * + * Warn the user, lest they think we're just buggy. + */ + printk(KERN_WARNING DRV_NAME ": Highpoint RocketRAID" + " BIOS CORRUPTS DATA on all attached drives," + " regardless of if/how they are configured." + " BEWARE!\n"); + printk(KERN_WARNING DRV_NAME ": For data safety, do not" + " use sectors 8-9 on \"Legacy\" drives," + " and avoid the final two gigabytes on" + " all RocketRAID BIOS initialized drives.\n"); + } + /* drop through */ case chip_6042: hpriv->ops = &mv6xxx_ops; - hp_flags |= MV_HP_GEN_IIE; + if (board_idx == chip_6042 && mv_pci_cut_through_okay(host)) + hp_flags |= MV_HP_CUT_THROUGH; - switch (rev_id) { - case 0x0: - hp_flags |= MV_HP_ERRATA_XX42A0; - break; - case 0x1: + switch (pdev->revision) { + case 0x2: /* Rev.B0: the first/only public release */ hp_flags |= MV_HP_ERRATA_60X1C0; break; default: - dev_printk(KERN_WARNING, &pdev->dev, - "Applying 60X1C0 workarounds to unknown rev\n"); + dev_warn(&pdev->dev, + "Applying 60X1C0 workarounds to unknown rev\n"); hp_flags |= MV_HP_ERRATA_60X1C0; break; } break; + case chip_soc: + if (soc_is_65n(hpriv)) + hpriv->ops = &mv_soc_65n_ops; + else + hpriv->ops = &mv_soc_ops; + hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE | + MV_HP_ERRATA_60X1C0; + break; default: - printk(KERN_ERR DRV_NAME ": BUG: invalid board index %u\n", board_idx); + dev_err(host->dev, "BUG: invalid board index %u\n", board_idx); return 1; } hpriv->hp_flags = hp_flags; + if (hp_flags & MV_HP_PCIE) { + hpriv->irq_cause_offset = PCIE_IRQ_CAUSE; + hpriv->irq_mask_offset = PCIE_IRQ_MASK; + hpriv->unmask_all_irqs = PCIE_UNMASK_ALL_IRQS; + } else { + hpriv->irq_cause_offset = PCI_IRQ_CAUSE; + hpriv->irq_mask_offset = PCI_IRQ_MASK; + hpriv->unmask_all_irqs = PCI_UNMASK_ALL_IRQS; + } return 0; } /** * mv_init_host - Perform some early initialization of the host. - * @pdev: host PCI device - * @probe_ent: early data struct representing the host + * @host: ATA host to initialize * * If possible, do an early global reset of the host. Then do * our port init and clear/unmask all/relevant host interrupts. @@ -2220,50 +3923,49 @@ static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, * LOCKING: * Inherited from caller. */ -static int mv_init_host(struct pci_dev *pdev, struct ata_probe_ent *probe_ent, - unsigned int board_idx) +static int mv_init_host(struct ata_host *host) { int rc = 0, n_hc, port, hc; - void __iomem *mmio = probe_ent->mmio_base; - struct mv_host_priv *hpriv = probe_ent->private_data; - - /* global interrupt mask */ - writel(0, mmio + HC_MAIN_IRQ_MASK_OFS); + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; - rc = mv_chip_id(pdev, hpriv, board_idx); + rc = mv_chip_id(host, hpriv->board_idx); if (rc) goto done; - n_hc = mv_get_hc_count(probe_ent->port_flags); - probe_ent->n_ports = MV_PORTS_PER_HC * n_hc; + if (IS_SOC(hpriv)) { + hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE; + hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK; + } else { + hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE; + hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK; + } + + /* initialize shadow irq mask with register's value */ + hpriv->main_irq_mask = readl(hpriv->main_irq_mask_addr); + + /* global interrupt mask: 0 == mask everything */ + mv_set_main_irq_mask(host, ~0, 0); - for (port = 0; port < probe_ent->n_ports; port++) - hpriv->ops->read_preamp(hpriv, port, mmio); + n_hc = mv_get_hc_count(host->ports[0]->flags); + + for (port = 0; port < host->n_ports; port++) + if (hpriv->ops->read_preamp) + hpriv->ops->read_preamp(hpriv, port, mmio); rc = hpriv->ops->reset_hc(hpriv, mmio, n_hc); if (rc) goto done; hpriv->ops->reset_flash(hpriv, mmio); - hpriv->ops->reset_bus(pdev, mmio); + hpriv->ops->reset_bus(host, mmio); hpriv->ops->enable_leds(hpriv, mmio); - for (port = 0; port < probe_ent->n_ports; port++) { - if (IS_60XX(hpriv)) { - void __iomem *port_mmio = mv_port_base(mmio, port); - - u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL); - ifctl |= (1 << 7); /* enable gen2i speed */ - ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */ - writelfl(ifctl, port_mmio + SATA_INTERFACE_CTL); - } - - hpriv->ops->phy_errata(hpriv, mmio, port); - } - - for (port = 0; port < probe_ent->n_ports; port++) { + for (port = 0; port < host->n_ports; port++) { + struct ata_port *ap = host->ports[port]; void __iomem *port_mmio = mv_port_base(mmio, port); - mv_port_init(&probe_ent->port[port], port_mmio); + + mv_port_init(&ap->ioaddr, port_mmio); } for (hc = 0; hc < n_hc; hc++) { @@ -2271,186 +3973,535 @@ static int mv_init_host(struct pci_dev *pdev, struct ata_probe_ent *probe_ent, VPRINTK("HC%i: HC config=0x%08x HC IRQ cause " "(before clear)=0x%08x\n", hc, - readl(hc_mmio + HC_CFG_OFS), - readl(hc_mmio + HC_IRQ_CAUSE_OFS)); + readl(hc_mmio + HC_CFG), + readl(hc_mmio + HC_IRQ_CAUSE)); /* Clear any currently outstanding hc interrupt conditions */ - writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS); + writelfl(0, hc_mmio + HC_IRQ_CAUSE); } - /* Clear any currently outstanding host interrupt conditions */ - writelfl(0, mmio + PCI_IRQ_CAUSE_OFS); + if (!IS_SOC(hpriv)) { + /* Clear any currently outstanding host interrupt conditions */ + writelfl(0, mmio + hpriv->irq_cause_offset); - /* and unmask interrupt generation for host regs */ - writelfl(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS); - writelfl(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS); - - VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x " - "PCI int cause/mask=0x%08x/0x%08x\n", - readl(mmio + HC_MAIN_IRQ_CAUSE_OFS), - readl(mmio + HC_MAIN_IRQ_MASK_OFS), - readl(mmio + PCI_IRQ_CAUSE_OFS), - readl(mmio + PCI_IRQ_MASK_OFS)); + /* and unmask interrupt generation for host regs */ + writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_offset); + } + /* + * enable only global host interrupts for now. + * The per-port interrupts get done later as ports are set up. + */ + mv_set_main_irq_mask(host, 0, PCI_ERR); + mv_set_irq_coalescing(host, irq_coalescing_io_count, + irq_coalescing_usecs); done: return rc; } +static int mv_create_dma_pools(struct mv_host_priv *hpriv, struct device *dev) +{ + hpriv->crqb_pool = dmam_pool_create("crqb_q", dev, MV_CRQB_Q_SZ, + MV_CRQB_Q_SZ, 0); + if (!hpriv->crqb_pool) + return -ENOMEM; + + hpriv->crpb_pool = dmam_pool_create("crpb_q", dev, MV_CRPB_Q_SZ, + MV_CRPB_Q_SZ, 0); + if (!hpriv->crpb_pool) + return -ENOMEM; + + hpriv->sg_tbl_pool = dmam_pool_create("sg_tbl", dev, MV_SG_TBL_SZ, + MV_SG_TBL_SZ, 0); + if (!hpriv->sg_tbl_pool) + return -ENOMEM; + + return 0; +} + +static void mv_conf_mbus_windows(struct mv_host_priv *hpriv, + const struct mbus_dram_target_info *dram) +{ + int i; + + for (i = 0; i < 4; i++) { + writel(0, hpriv->base + WINDOW_CTRL(i)); + writel(0, hpriv->base + WINDOW_BASE(i)); + } + + for (i = 0; i < dram->num_cs; i++) { + const struct mbus_dram_window *cs = dram->cs + i; + + writel(((cs->size - 1) & 0xffff0000) | + (cs->mbus_attr << 8) | + (dram->mbus_dram_target_id << 4) | 1, + hpriv->base + WINDOW_CTRL(i)); + writel(cs->base, hpriv->base + WINDOW_BASE(i)); + } +} + +/** + * mv_platform_probe - handle a positive probe of an soc Marvell + * host + * @pdev: platform device found + * + * LOCKING: + * Inherited from caller. + */ +static int mv_platform_probe(struct platform_device *pdev) +{ + const struct mv_sata_platform_data *mv_platform_data; + const struct mbus_dram_target_info *dram; + const struct ata_port_info *ppi[] = + { &mv_port_info[chip_soc], NULL }; + struct ata_host *host; + struct mv_host_priv *hpriv; + struct resource *res; + int n_ports = 0, irq = 0; + int rc; + int port; + + ata_print_version_once(&pdev->dev, DRV_VERSION); + + /* + * Simple resource validation .. + */ + if (unlikely(pdev->num_resources != 2)) { + dev_err(&pdev->dev, "invalid number of resources\n"); + return -EINVAL; + } + + /* + * Get the register base first + */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res == NULL) + return -EINVAL; + + /* allocate host */ + if (pdev->dev.of_node) { + of_property_read_u32(pdev->dev.of_node, "nr-ports", &n_ports); + irq = irq_of_parse_and_map(pdev->dev.of_node, 0); + } else { + mv_platform_data = dev_get_platdata(&pdev->dev); + n_ports = mv_platform_data->n_ports; + irq = platform_get_irq(pdev, 0); + } + + host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports); + hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL); + + if (!host || !hpriv) + return -ENOMEM; + hpriv->port_clks = devm_kzalloc(&pdev->dev, + sizeof(struct clk *) * n_ports, + GFP_KERNEL); + if (!hpriv->port_clks) + return -ENOMEM; + hpriv->port_phys = devm_kzalloc(&pdev->dev, + sizeof(struct phy *) * n_ports, + GFP_KERNEL); + if (!hpriv->port_phys) + return -ENOMEM; + host->private_data = hpriv; + hpriv->board_idx = chip_soc; + + host->iomap = NULL; + hpriv->base = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + hpriv->base -= SATAHC0_REG_BASE; + + hpriv->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(hpriv->clk)) + dev_notice(&pdev->dev, "cannot get optional clkdev\n"); + else + clk_prepare_enable(hpriv->clk); + + for (port = 0; port < n_ports; port++) { + char port_number[16]; + sprintf(port_number, "%d", port); + hpriv->port_clks[port] = clk_get(&pdev->dev, port_number); + if (!IS_ERR(hpriv->port_clks[port])) + clk_prepare_enable(hpriv->port_clks[port]); + + sprintf(port_number, "port%d", port); + hpriv->port_phys[port] = devm_phy_optional_get(&pdev->dev, + port_number); + if (IS_ERR(hpriv->port_phys[port])) { + rc = PTR_ERR(hpriv->port_phys[port]); + hpriv->port_phys[port] = NULL; + if (rc != -EPROBE_DEFER) + dev_warn(&pdev->dev, "error getting phy %d", rc); + + /* Cleanup only the initialized ports */ + hpriv->n_ports = port; + goto err; + } else + phy_power_on(hpriv->port_phys[port]); + } + + /* All the ports have been initialized */ + hpriv->n_ports = n_ports; + + /* + * (Re-)program MBUS remapping windows if we are asked to. + */ + dram = mv_mbus_dram_info(); + if (dram) + mv_conf_mbus_windows(hpriv, dram); + + rc = mv_create_dma_pools(hpriv, &pdev->dev); + if (rc) + goto err; + + /* + * To allow disk hotplug on Armada 370/XP SoCs, the PHY speed must be + * updated in the LP_PHY_CTL register. + */ + if (pdev->dev.of_node && + of_device_is_compatible(pdev->dev.of_node, + "marvell,armada-370-sata")) + hpriv->hp_flags |= MV_HP_FIX_LP_PHY_CTL; + + /* initialize adapter */ + rc = mv_init_host(host); + if (rc) + goto err; + + dev_info(&pdev->dev, "slots %u ports %d\n", + (unsigned)MV_MAX_Q_DEPTH, host->n_ports); + + rc = ata_host_activate(host, irq, mv_interrupt, IRQF_SHARED, &mv6_sht); + if (!rc) + return 0; + +err: + if (!IS_ERR(hpriv->clk)) { + clk_disable_unprepare(hpriv->clk); + clk_put(hpriv->clk); + } + for (port = 0; port < hpriv->n_ports; port++) { + if (!IS_ERR(hpriv->port_clks[port])) { + clk_disable_unprepare(hpriv->port_clks[port]); + clk_put(hpriv->port_clks[port]); + } + if (hpriv->port_phys[port]) + phy_power_off(hpriv->port_phys[port]); + } + + return rc; +} + +/* + * + * mv_platform_remove - unplug a platform interface + * @pdev: platform device + * + * A platform bus SATA device has been unplugged. Perform the needed + * cleanup. Also called on module unload for any active devices. + */ +static int mv_platform_remove(struct platform_device *pdev) +{ + struct ata_host *host = platform_get_drvdata(pdev); + struct mv_host_priv *hpriv = host->private_data; + int port; + ata_host_detach(host); + + if (!IS_ERR(hpriv->clk)) { + clk_disable_unprepare(hpriv->clk); + clk_put(hpriv->clk); + } + for (port = 0; port < host->n_ports; port++) { + if (!IS_ERR(hpriv->port_clks[port])) { + clk_disable_unprepare(hpriv->port_clks[port]); + clk_put(hpriv->port_clks[port]); + } + if (hpriv->port_phys[port]) + phy_power_off(hpriv->port_phys[port]); + } + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int mv_platform_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct ata_host *host = platform_get_drvdata(pdev); + if (host) + return ata_host_suspend(host, state); + else + return 0; +} + +static int mv_platform_resume(struct platform_device *pdev) +{ + struct ata_host *host = platform_get_drvdata(pdev); + const struct mbus_dram_target_info *dram; + int ret; + + if (host) { + struct mv_host_priv *hpriv = host->private_data; + + /* + * (Re-)program MBUS remapping windows if we are asked to. + */ + dram = mv_mbus_dram_info(); + if (dram) + mv_conf_mbus_windows(hpriv, dram); + + /* initialize adapter */ + ret = mv_init_host(host); + if (ret) { + printk(KERN_ERR DRV_NAME ": Error during HW init\n"); + return ret; + } + ata_host_resume(host); + } + + return 0; +} +#else +#define mv_platform_suspend NULL +#define mv_platform_resume NULL +#endif + +#ifdef CONFIG_OF +static struct of_device_id mv_sata_dt_ids[] = { + { .compatible = "marvell,armada-370-sata", }, + { .compatible = "marvell,orion-sata", }, + {}, +}; +MODULE_DEVICE_TABLE(of, mv_sata_dt_ids); +#endif + +static struct platform_driver mv_platform_driver = { + .probe = mv_platform_probe, + .remove = mv_platform_remove, + .suspend = mv_platform_suspend, + .resume = mv_platform_resume, + .driver = { + .name = DRV_NAME, + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(mv_sata_dt_ids), + }, +}; + + +#ifdef CONFIG_PCI +static int mv_pci_init_one(struct pci_dev *pdev, + const struct pci_device_id *ent); +#ifdef CONFIG_PM_SLEEP +static int mv_pci_device_resume(struct pci_dev *pdev); +#endif + + +static struct pci_driver mv_pci_driver = { + .name = DRV_NAME, + .id_table = mv_pci_tbl, + .probe = mv_pci_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = mv_pci_device_resume, +#endif + +}; + +/* move to PCI layer or libata core? */ +static int pci_go_64(struct pci_dev *pdev) +{ + int rc; + + if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) { + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)); + if (rc) { + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); + if (rc) { + dev_err(&pdev->dev, + "64-bit DMA enable failed\n"); + return rc; + } + } + } else { + rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); + if (rc) { + dev_err(&pdev->dev, "32-bit DMA enable failed\n"); + return rc; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); + if (rc) { + dev_err(&pdev->dev, + "32-bit consistent DMA enable failed\n"); + return rc; + } + } + + return rc; +} + /** * mv_print_info - Dump key info to kernel log for perusal. - * @probe_ent: early data struct representing the host + * @host: ATA host to print info about * * FIXME: complete this. * * LOCKING: * Inherited from caller. */ -static void mv_print_info(struct ata_probe_ent *probe_ent) +static void mv_print_info(struct ata_host *host) { - struct pci_dev *pdev = to_pci_dev(probe_ent->dev); - struct mv_host_priv *hpriv = probe_ent->private_data; - u8 rev_id, scc; - const char *scc_s; + struct pci_dev *pdev = to_pci_dev(host->dev); + struct mv_host_priv *hpriv = host->private_data; + u8 scc; + const char *scc_s, *gen; /* Use this to determine the HW stepping of the chip so we know * what errata to workaround */ - pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id); - pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &scc); if (scc == 0) scc_s = "SCSI"; else if (scc == 0x01) scc_s = "RAID"; else - scc_s = "unknown"; + scc_s = "?"; + + if (IS_GEN_I(hpriv)) + gen = "I"; + else if (IS_GEN_II(hpriv)) + gen = "II"; + else if (IS_GEN_IIE(hpriv)) + gen = "IIE"; + else + gen = "?"; - dev_printk(KERN_INFO, &pdev->dev, - "%u slots %u ports %s mode IRQ via %s\n", - (unsigned)MV_MAX_Q_DEPTH, probe_ent->n_ports, - scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx"); + dev_info(&pdev->dev, "Gen-%s %u slots %u ports %s mode IRQ via %s\n", + gen, (unsigned)MV_MAX_Q_DEPTH, host->n_ports, + scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx"); } /** - * mv_init_one - handle a positive probe of a Marvell host + * mv_pci_init_one - handle a positive probe of a PCI Marvell host * @pdev: PCI device found * @ent: PCI device ID entry for the matched host * * LOCKING: * Inherited from caller. */ -static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +static int mv_pci_init_one(struct pci_dev *pdev, + const struct pci_device_id *ent) { - static int printed_version = 0; - struct ata_probe_ent *probe_ent = NULL; - struct mv_host_priv *hpriv; unsigned int board_idx = (unsigned int)ent->driver_data; - void __iomem *mmio_base; - int pci_dev_busy = 0, rc; + const struct ata_port_info *ppi[] = { &mv_port_info[board_idx], NULL }; + struct ata_host *host; + struct mv_host_priv *hpriv; + int n_ports, port, rc; - if (!printed_version++) - dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n"); + ata_print_version_once(&pdev->dev, DRV_VERSION); - rc = pci_enable_device(pdev); - if (rc) { - return rc; - } - pci_set_master(pdev); + /* allocate host */ + n_ports = mv_get_hc_count(ppi[0]->flags) * MV_PORTS_PER_HC; - rc = pci_request_regions(pdev, DRV_NAME); - if (rc) { - pci_dev_busy = 1; - goto err_out; - } + host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports); + hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL); + if (!host || !hpriv) + return -ENOMEM; + host->private_data = hpriv; + hpriv->n_ports = n_ports; + hpriv->board_idx = board_idx; - probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); - if (probe_ent == NULL) { - rc = -ENOMEM; - goto err_out_regions; - } + /* acquire resources */ + rc = pcim_enable_device(pdev); + if (rc) + return rc; - memset(probe_ent, 0, sizeof(*probe_ent)); - probe_ent->dev = pci_dev_to_dev(pdev); - INIT_LIST_HEAD(&probe_ent->node); + rc = pcim_iomap_regions(pdev, 1 << MV_PRIMARY_BAR, DRV_NAME); + if (rc == -EBUSY) + pcim_pin_device(pdev); + if (rc) + return rc; + host->iomap = pcim_iomap_table(pdev); + hpriv->base = host->iomap[MV_PRIMARY_BAR]; - mmio_base = pci_iomap(pdev, MV_PRIMARY_BAR, 0); - if (mmio_base == NULL) { - rc = -ENOMEM; - goto err_out_free_ent; - } + rc = pci_go_64(pdev); + if (rc) + return rc; - hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL); - if (!hpriv) { - rc = -ENOMEM; - goto err_out_iounmap; - } - memset(hpriv, 0, sizeof(*hpriv)); + rc = mv_create_dma_pools(hpriv, &pdev->dev); + if (rc) + return rc; - probe_ent->sht = mv_port_info[board_idx].sht; - probe_ent->port_flags = mv_port_info[board_idx].flags; - probe_ent->pio_mask = mv_port_info[board_idx].pio_mask; - probe_ent->udma_mask = mv_port_info[board_idx].udma_mask; - probe_ent->port_ops = mv_port_info[board_idx].port_ops; + for (port = 0; port < host->n_ports; port++) { + struct ata_port *ap = host->ports[port]; + void __iomem *port_mmio = mv_port_base(hpriv->base, port); + unsigned int offset = port_mmio - hpriv->base; - probe_ent->irq = pdev->irq; - probe_ent->irq_flags = IRQF_SHARED; - probe_ent->mmio_base = mmio_base; - probe_ent->private_data = hpriv; + ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio"); + ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port"); + } /* initialize adapter */ - rc = mv_init_host(pdev, probe_ent, board_idx); - if (rc) { - goto err_out_hpriv; - } + rc = mv_init_host(host); + if (rc) + return rc; - /* Enable interrupts */ - if (msi && pci_enable_msi(pdev) == 0) { + /* Enable message-switched interrupts, if requested */ + if (msi && pci_enable_msi(pdev) == 0) hpriv->hp_flags |= MV_HP_FLAG_MSI; - } else { - pci_intx(pdev, 1); - } mv_dump_pci_cfg(pdev, 0x68); - mv_print_info(probe_ent); + mv_print_info(host); - if (ata_device_add(probe_ent) == 0) { - rc = -ENODEV; /* No devices discovered */ - goto err_out_dev_add; - } + pci_set_master(pdev); + pci_try_set_mwi(pdev); + return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED, + IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht); +} - kfree(probe_ent); - return 0; +#ifdef CONFIG_PM_SLEEP +static int mv_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = pci_get_drvdata(pdev); + int rc; -err_out_dev_add: - if (MV_HP_FLAG_MSI & hpriv->hp_flags) { - pci_disable_msi(pdev); - } else { - pci_intx(pdev, 0); - } -err_out_hpriv: - kfree(hpriv); -err_out_iounmap: - pci_iounmap(pdev, mmio_base); -err_out_free_ent: - kfree(probe_ent); -err_out_regions: - pci_release_regions(pdev); -err_out: - if (!pci_dev_busy) { - pci_disable_device(pdev); - } + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; - return rc; + /* initialize adapter */ + rc = mv_init_host(host); + if (rc) + return rc; + + ata_host_resume(host); + + return 0; } +#endif +#endif static int __init mv_init(void) { - return pci_register_driver(&mv_pci_driver); + int rc = -ENODEV; +#ifdef CONFIG_PCI + rc = pci_register_driver(&mv_pci_driver); + if (rc < 0) + return rc; +#endif + rc = platform_driver_register(&mv_platform_driver); + +#ifdef CONFIG_PCI + if (rc < 0) + pci_unregister_driver(&mv_pci_driver); +#endif + return rc; } static void __exit mv_exit(void) { +#ifdef CONFIG_PCI pci_unregister_driver(&mv_pci_driver); +#endif + platform_driver_unregister(&mv_platform_driver); } MODULE_AUTHOR("Brett Russ"); @@ -2458,9 +4509,7 @@ MODULE_DESCRIPTION("SCSI low-level driver for Marvell SATA controllers"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, mv_pci_tbl); MODULE_VERSION(DRV_VERSION); - -module_param(msi, int, 0444); -MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)"); +MODULE_ALIAS("platform:" DRV_NAME); module_init(mv_init); module_exit(mv_exit); |