diff options
Diffstat (limited to 'drivers/ata/ata_piix.c')
| -rw-r--r-- | drivers/ata/ata_piix.c | 766 |
1 files changed, 436 insertions, 330 deletions
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index 6cb14ca8ee8..893e30e9a9e 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -1,7 +1,7 @@ /* * ata_piix.c - Intel PATA/SATA controllers * - * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Maintained by: Tejun Heo <tj@kernel.org> * Please ALWAYS copy linux-ide@vger.kernel.org * on emails. * @@ -38,16 +38,16 @@ * Hardware documentation available at http://developer.intel.com/ * * Documentation - * Publically available from Intel web site. Errata documentation - * is also publically available. As an aide to anyone hacking on this + * Publicly available from Intel web site. Errata documentation + * is also publicly available. As an aide to anyone hacking on this * driver the list of errata that are relevant is below, going back to * PIIX4. Older device documentation is now a bit tricky to find. * * The chipsets all follow very much the same design. The original Triton - * series chipsets do _not_ support independant device timings, but this + * series chipsets do _not_ support independent device timings, but this * is fixed in Triton II. With the odd mobile exception the chips then * change little except in gaining more modes until SATA arrives. This - * driver supports only the chips with independant timing (that is those + * driver supports only the chips with independent timing (that is those * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix * for the early chip drivers. * @@ -100,7 +100,7 @@ enum { PIIX_IOCFG = 0x54, /* IDE I/O configuration register */ - ICH5_PMR = 0x90, /* port mapping register */ + ICH5_PMR = 0x90, /* address map register */ ICH5_PCS = 0x92, /* port control and status */ PIIX_SIDPR_BAR = 5, PIIX_SIDPR_LEN = 16, @@ -113,6 +113,8 @@ enum { PIIX_PATA_FLAGS = ATA_FLAG_SLAVE_POSS, PIIX_SATA_FLAGS = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR, + PIIX_FLAG_PIO16 = (1 << 30), /*support 16bit PIO only*/ + PIIX_80C_PRI = (1 << 5) | (1 << 4), PIIX_80C_SEC = (1 << 7) | (1 << 6), @@ -122,7 +124,7 @@ enum { P2 = 2, /* port 2 */ P3 = 3, /* port 3 */ IDE = -1, /* IDE */ - NA = -2, /* not avaliable */ + NA = -2, /* not available */ RV = -3, /* reserved */ PIIX_AHCI_DEVICE = 6, @@ -147,6 +149,9 @@ enum piix_controller_ids { ich8m_apple_sata, /* locks up on second port enable */ tolapai_sata, piix_pata_vmw, /* PIIX4 for VMware, spurious DMA_ERR */ + ich8_sata_snb, + ich8_2port_sata_snb, + ich8_2port_sata_byt, }; struct piix_map_db { @@ -161,27 +166,6 @@ struct piix_host_priv { void __iomem *sidpr; }; -static int piix_init_one(struct pci_dev *pdev, - const struct pci_device_id *ent); -static void piix_remove_one(struct pci_dev *pdev); -static int piix_pata_prereset(struct ata_link *link, unsigned long deadline); -static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev); -static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev); -static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev); -static int ich_pata_cable_detect(struct ata_port *ap); -static u8 piix_vmw_bmdma_status(struct ata_port *ap); -static int piix_sidpr_scr_read(struct ata_link *link, - unsigned int reg, u32 *val); -static int piix_sidpr_scr_write(struct ata_link *link, - unsigned int reg, u32 val); -static int piix_sidpr_set_lpm(struct ata_link *link, enum ata_lpm_policy policy, - unsigned hints); -static bool piix_irq_check(struct ata_port *ap); -#ifdef CONFIG_PM -static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg); -static int piix_pci_device_resume(struct pci_dev *pdev); -#endif - static unsigned int in_module_init = 1; static const struct pci_device_id piix_pci_tbl[] = { @@ -230,7 +214,7 @@ static const struct pci_device_id piix_pci_tbl[] = { { 0x8086, 0x2850, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, /* SATA ports */ - + /* 82801EB (ICH5) */ { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata }, /* 82801EB (ICH5) */ @@ -249,7 +233,7 @@ static const struct pci_device_id piix_pci_tbl[] = { PCI_CLASS_STORAGE_IDE << 8, 0xffff00, ich6m_sata }, /* 82801GB/GR/GH (ICH7, identical to ICH6) */ { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata }, - /* 2801GBM/GHM (ICH7M, identical to ICH6M) */ + /* 82801GBM/GHM (ICH7M, identical to ICH6M) */ { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata }, /* Enterprise Southbridge 2 (631xESB/632xESB) */ { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata }, @@ -298,75 +282,66 @@ static const struct pci_device_id piix_pci_tbl[] = { /* SATA Controller IDE (PCH) */ { 0x8086, 0x3b2e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, /* SATA Controller IDE (CPT) */ - { 0x8086, 0x1c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, + { 0x8086, 0x1c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, /* SATA Controller IDE (CPT) */ - { 0x8086, 0x1c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, + { 0x8086, 0x1c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, /* SATA Controller IDE (CPT) */ { 0x8086, 0x1c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, /* SATA Controller IDE (CPT) */ { 0x8086, 0x1c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, /* SATA Controller IDE (PBG) */ - { 0x8086, 0x1d00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, + { 0x8086, 0x1d00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, /* SATA Controller IDE (PBG) */ { 0x8086, 0x1d08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, - { } /* terminate list */ -}; - -static struct pci_driver piix_pci_driver = { - .name = DRV_NAME, - .id_table = piix_pci_tbl, - .probe = piix_init_one, - .remove = piix_remove_one, -#ifdef CONFIG_PM - .suspend = piix_pci_device_suspend, - .resume = piix_pci_device_resume, -#endif -}; - -static struct scsi_host_template piix_sht = { - ATA_BMDMA_SHT(DRV_NAME), -}; - -static struct ata_port_operations piix_sata_ops = { - .inherits = &ata_bmdma32_port_ops, - .sff_irq_check = piix_irq_check, -}; - -static struct ata_port_operations piix_pata_ops = { - .inherits = &piix_sata_ops, - .cable_detect = ata_cable_40wire, - .set_piomode = piix_set_piomode, - .set_dmamode = piix_set_dmamode, - .prereset = piix_pata_prereset, -}; - -static struct ata_port_operations piix_vmw_ops = { - .inherits = &piix_pata_ops, - .bmdma_status = piix_vmw_bmdma_status, -}; - -static struct ata_port_operations ich_pata_ops = { - .inherits = &piix_pata_ops, - .cable_detect = ich_pata_cable_detect, - .set_dmamode = ich_set_dmamode, -}; - -static struct device_attribute *piix_sidpr_shost_attrs[] = { - &dev_attr_link_power_management_policy, - NULL -}; + /* SATA Controller IDE (Panther Point) */ + { 0x8086, 0x1e00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Panther Point) */ + { 0x8086, 0x1e01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Panther Point) */ + { 0x8086, 0x1e08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Panther Point) */ + { 0x8086, 0x1e09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Lynx Point) */ + { 0x8086, 0x8c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Lynx Point) */ + { 0x8086, 0x8c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Lynx Point) */ + { 0x8086, 0x8c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_snb }, + /* SATA Controller IDE (Lynx Point) */ + { 0x8086, 0x8c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Lynx Point-LP) */ + { 0x8086, 0x9c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Lynx Point-LP) */ + { 0x8086, 0x9c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Lynx Point-LP) */ + { 0x8086, 0x9c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Lynx Point-LP) */ + { 0x8086, 0x9c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (DH89xxCC) */ + { 0x8086, 0x2326, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Avoton) */ + { 0x8086, 0x1f20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Avoton) */ + { 0x8086, 0x1f21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Avoton) */ + { 0x8086, 0x1f30, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Avoton) */ + { 0x8086, 0x1f31, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (Wellsburg) */ + { 0x8086, 0x8d00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Wellsburg) */ + { 0x8086, 0x8d08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_snb }, + /* SATA Controller IDE (Wellsburg) */ + { 0x8086, 0x8d60, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (Wellsburg) */ + { 0x8086, 0x8d68, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (BayTrail) */ + { 0x8086, 0x0F20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_byt }, + { 0x8086, 0x0F21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_byt }, + /* SATA Controller IDE (Coleto Creek) */ + { 0x8086, 0x23a6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, -static struct scsi_host_template piix_sidpr_sht = { - ATA_BMDMA_SHT(DRV_NAME), - .shost_attrs = piix_sidpr_shost_attrs, -}; - -static struct ata_port_operations piix_sidpr_sata_ops = { - .inherits = &piix_sata_ops, - .hardreset = sata_std_hardreset, - .scr_read = piix_sidpr_scr_read, - .scr_write = piix_sidpr_scr_write, - .set_lpm = piix_sidpr_set_lpm, + { } /* terminate list */ }; static const struct piix_map_db ich5_map_db = { @@ -470,134 +445,9 @@ static const struct piix_map_db *piix_map_db_table[] = { [ich8_2port_sata] = &ich8_2port_map_db, [ich8m_apple_sata] = &ich8m_apple_map_db, [tolapai_sata] = &tolapai_map_db, -}; - -static struct ata_port_info piix_port_info[] = { - [piix_pata_mwdma] = /* PIIX3 MWDMA only */ - { - .flags = PIIX_PATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ - .port_ops = &piix_pata_ops, - }, - - [piix_pata_33] = /* PIIX4 at 33MHz */ - { - .flags = PIIX_PATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ - .udma_mask = ATA_UDMA2, - .port_ops = &piix_pata_ops, - }, - - [ich_pata_33] = /* ICH0 - ICH at 33Mhz*/ - { - .flags = PIIX_PATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA12_ONLY, /* Check: maybe MWDMA0 is ok */ - .udma_mask = ATA_UDMA2, - .port_ops = &ich_pata_ops, - }, - - [ich_pata_66] = /* ICH controllers up to 66MHz */ - { - .flags = PIIX_PATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA12_ONLY, /* MWDMA0 is broken on chip */ - .udma_mask = ATA_UDMA4, - .port_ops = &ich_pata_ops, - }, - - [ich_pata_100] = - { - .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA12_ONLY, - .udma_mask = ATA_UDMA5, - .port_ops = &ich_pata_ops, - }, - - [ich_pata_100_nomwdma1] = - { - .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2_ONLY, - .udma_mask = ATA_UDMA5, - .port_ops = &ich_pata_ops, - }, - - [ich5_sata] = - { - .flags = PIIX_SATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [ich6_sata] = - { - .flags = PIIX_SATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [ich6m_sata] = - { - .flags = PIIX_SATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [ich8_sata] = - { - .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [ich8_2port_sata] = - { - .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [tolapai_sata] = - { - .flags = PIIX_SATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [ich8m_apple_sata] = - { - .flags = PIIX_SATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, - .port_ops = &piix_sata_ops, - }, - - [piix_pata_vmw] = - { - .flags = PIIX_PATA_FLAGS, - .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ - .udma_mask = ATA_UDMA2, - .port_ops = &piix_vmw_ops, - }, - + [ich8_sata_snb] = &ich8_map_db, + [ich8_2port_sata_snb] = &ich8_2port_map_db, + [ich8_2port_sata_byt] = &ich8_2port_map_db, }; static struct pci_bits piix_enable_bits[] = { @@ -641,6 +491,14 @@ static const struct ich_laptop ich_laptop[] = { { 0, } }; +static int piix_port_start(struct ata_port *ap) +{ + if (!(ap->flags & PIIX_FLAG_PIO16)) + ap->pflags |= ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE; + + return ata_bmdma_port_start(ap); +} + /** * ich_pata_cable_detect - Probe host controller cable detect info * @ap: Port for which cable detect info is desired @@ -659,7 +517,7 @@ static int ich_pata_cable_detect(struct ata_port *ap) const struct ich_laptop *lap = &ich_laptop[0]; u8 mask; - /* Check for specials - Acer Aspire 5602WLMi */ + /* Check for specials */ while (lap->device) { if (lap->device == pdev->device && lap->subvendor == pdev->subsystem_vendor && @@ -696,22 +554,11 @@ static int piix_pata_prereset(struct ata_link *link, unsigned long deadline) static DEFINE_SPINLOCK(piix_lock); -/** - * piix_set_piomode - Initialize host controller PATA PIO timings - * @ap: Port whose timings we are configuring - * @adev: um - * - * Set PIO mode for device, in host controller PCI config space. - * - * LOCKING: - * None (inherited from caller). - */ - -static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev) +static void piix_set_timings(struct ata_port *ap, struct ata_device *adev, + u8 pio) { struct pci_dev *dev = to_pci_dev(ap->host->dev); unsigned long flags; - unsigned int pio = adev->pio_mode - XFER_PIO_0; unsigned int is_slave = (adev->devno != 0); unsigned int master_port= ap->port_no ? 0x42 : 0x40; unsigned int slave_port = 0x44; @@ -736,10 +583,16 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev) control |= 1; /* TIME1 enable */ if (ata_pio_need_iordy(adev)) control |= 2; /* IE enable */ - /* Intel specifies that the PPE functionality is for disk only */ if (adev->class == ATA_DEV_ATA) control |= 4; /* PPE enable */ + /* + * If the drive MWDMA is faster than it can do PIO then + * we must force PIO into PIO0 + */ + if (adev->pio_mode < XFER_PIO_0 + pio) + /* Enable DMA timing only */ + control |= 8; /* PIO cycles in PIO0 */ spin_lock_irqsave(&piix_lock, flags); @@ -751,8 +604,6 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev) if (is_slave) { /* clear TIME1|IE1|PPE1|DTE1 */ master_data &= 0xff0f; - /* Enable SITRE (separate slave timing register) */ - master_data |= 0x4000; /* enable PPE1, IE1 and TIME1 as needed */ master_data |= (control << 4); pci_read_config_byte(dev, slave_port, &slave_data); @@ -770,6 +621,9 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev) (timings[pio][0] << 12) | (timings[pio][1] << 8); } + + /* Enable SITRE (separate slave timing register) */ + master_data |= 0x4000; pci_write_config_word(dev, master_port, master_data); if (is_slave) pci_write_config_byte(dev, slave_port, slave_data); @@ -787,6 +641,22 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev) } /** + * piix_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Drive in question + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + piix_set_timings(ap, adev, adev->pio_mode - XFER_PIO_0); +} + +/** * do_pata_set_dmamode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Drive in question @@ -802,31 +672,20 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in { struct pci_dev *dev = to_pci_dev(ap->host->dev); unsigned long flags; - u8 master_port = ap->port_no ? 0x42 : 0x40; - u16 master_data; u8 speed = adev->dma_mode; int devid = adev->devno + 2 * ap->port_no; u8 udma_enable = 0; - static const /* ISP RTC */ - u8 timings[][2] = { { 0, 0 }, - { 0, 0 }, - { 1, 0 }, - { 2, 1 }, - { 2, 3 }, }; - - spin_lock_irqsave(&piix_lock, flags); - - pci_read_config_word(dev, master_port, &master_data); - if (ap->udma_mask) - pci_read_config_byte(dev, 0x48, &udma_enable); - if (speed >= XFER_UDMA_0) { - unsigned int udma = adev->dma_mode - XFER_UDMA_0; + unsigned int udma = speed - XFER_UDMA_0; u16 udma_timing; u16 ideconf; int u_clock, u_speed; + spin_lock_irqsave(&piix_lock, flags); + + pci_read_config_byte(dev, 0x48, &udma_enable); + /* * UDMA is handled by a combination of clock switching and * selection of dividers @@ -859,56 +718,21 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in performance (WR_PingPong_En) */ pci_write_config_word(dev, 0x54, ideconf); } + + pci_write_config_byte(dev, 0x48, udma_enable); + + spin_unlock_irqrestore(&piix_lock, flags); } else { - /* - * MWDMA is driven by the PIO timings. We must also enable - * IORDY unconditionally along with TIME1. PPE has already - * been set when the PIO timing was set. - */ - unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; - unsigned int control; - u8 slave_data; + /* MWDMA is driven by the PIO timings. */ + unsigned int mwdma = speed - XFER_MW_DMA_0; const unsigned int needed_pio[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 }; int pio = needed_pio[mwdma] - XFER_PIO_0; - control = 3; /* IORDY|TIME1 */ - - /* If the drive MWDMA is faster than it can do PIO then - we must force PIO into PIO0 */ - - if (adev->pio_mode < needed_pio[mwdma]) - /* Enable DMA timing only */ - control |= 8; /* PIO cycles in PIO0 */ - - if (adev->devno) { /* Slave */ - master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ - master_data |= control << 4; - pci_read_config_byte(dev, 0x44, &slave_data); - slave_data &= (ap->port_no ? 0x0f : 0xf0); - /* Load the matching timing */ - slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); - pci_write_config_byte(dev, 0x44, slave_data); - } else { /* Master */ - master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY - and master timing bits */ - master_data |= control; - master_data |= - (timings[pio][0] << 12) | - (timings[pio][1] << 8); - } - - if (ap->udma_mask) - udma_enable &= ~(1 << devid); - - pci_write_config_word(dev, master_port, master_data); + /* XFER_PIO_0 is never used currently */ + piix_set_timings(ap, adev, pio); } - /* Don't scribble on 0x48 if the controller does not support UDMA */ - if (ap->udma_mask) - pci_write_config_byte(dev, 0x48, udma_enable); - - spin_unlock_irqrestore(&piix_lock, flags); } /** @@ -1006,7 +830,7 @@ static bool piix_irq_check(struct ata_port *ap) return ap->ops->bmdma_status(ap) & ATA_DMA_INTR; } -#ifdef CONFIG_PM +#ifdef CONFIG_PM_SLEEP static int piix_broken_suspend(void) { static const struct dmi_system_id sysids[] = { @@ -1116,6 +940,13 @@ static int piix_broken_suspend(void) }, }, { + .ident = "Satellite Pro A120", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "Satellite Pro A120"), + }, + }, + { .ident = "Portege M500", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), @@ -1164,7 +995,7 @@ static int piix_broken_suspend(void) static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg) { - struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct ata_host *host = pci_get_drvdata(pdev); unsigned long flags; int rc = 0; @@ -1199,7 +1030,7 @@ static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg) static int piix_pci_device_resume(struct pci_dev *pdev) { - struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct ata_host *host = pci_get_drvdata(pdev); unsigned long flags; int rc; @@ -1217,8 +1048,9 @@ static int piix_pci_device_resume(struct pci_dev *pdev) */ rc = pci_reenable_device(pdev); if (rc) - dev_printk(KERN_ERR, &pdev->dev, "failed to enable " - "device after resume (%d)\n", rc); + dev_err(&pdev->dev, + "failed to enable device after resume (%d)\n", + rc); } else rc = ata_pci_device_do_resume(pdev); @@ -1234,6 +1066,213 @@ static u8 piix_vmw_bmdma_status(struct ata_port *ap) return ata_bmdma_status(ap) & ~ATA_DMA_ERR; } +static struct scsi_host_template piix_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations piix_sata_ops = { + .inherits = &ata_bmdma32_port_ops, + .sff_irq_check = piix_irq_check, + .port_start = piix_port_start, +}; + +static struct ata_port_operations piix_pata_ops = { + .inherits = &piix_sata_ops, + .cable_detect = ata_cable_40wire, + .set_piomode = piix_set_piomode, + .set_dmamode = piix_set_dmamode, + .prereset = piix_pata_prereset, +}; + +static struct ata_port_operations piix_vmw_ops = { + .inherits = &piix_pata_ops, + .bmdma_status = piix_vmw_bmdma_status, +}; + +static struct ata_port_operations ich_pata_ops = { + .inherits = &piix_pata_ops, + .cable_detect = ich_pata_cable_detect, + .set_dmamode = ich_set_dmamode, +}; + +static struct device_attribute *piix_sidpr_shost_attrs[] = { + &dev_attr_link_power_management_policy, + NULL +}; + +static struct scsi_host_template piix_sidpr_sht = { + ATA_BMDMA_SHT(DRV_NAME), + .shost_attrs = piix_sidpr_shost_attrs, +}; + +static struct ata_port_operations piix_sidpr_sata_ops = { + .inherits = &piix_sata_ops, + .hardreset = sata_std_hardreset, + .scr_read = piix_sidpr_scr_read, + .scr_write = piix_sidpr_scr_write, + .set_lpm = piix_sidpr_set_lpm, +}; + +static struct ata_port_info piix_port_info[] = { + [piix_pata_mwdma] = /* PIIX3 MWDMA only */ + { + .flags = PIIX_PATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ + .port_ops = &piix_pata_ops, + }, + + [piix_pata_33] = /* PIIX4 at 33MHz */ + { + .flags = PIIX_PATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ + .udma_mask = ATA_UDMA2, + .port_ops = &piix_pata_ops, + }, + + [ich_pata_33] = /* ICH0 - ICH at 33Mhz*/ + { + .flags = PIIX_PATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, /* Check: maybe MWDMA0 is ok */ + .udma_mask = ATA_UDMA2, + .port_ops = &ich_pata_ops, + }, + + [ich_pata_66] = /* ICH controllers up to 66MHz */ + { + .flags = PIIX_PATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, /* MWDMA0 is broken on chip */ + .udma_mask = ATA_UDMA4, + .port_ops = &ich_pata_ops, + }, + + [ich_pata_100] = + { + .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, + .udma_mask = ATA_UDMA5, + .port_ops = &ich_pata_ops, + }, + + [ich_pata_100_nomwdma1] = + { + .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2_ONLY, + .udma_mask = ATA_UDMA5, + .port_ops = &ich_pata_ops, + }, + + [ich5_sata] = + { + .flags = PIIX_SATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich6_sata] = + { + .flags = PIIX_SATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich6m_sata] = + { + .flags = PIIX_SATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich8_sata] = + { + .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich8_2port_sata] = + { + .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [tolapai_sata] = + { + .flags = PIIX_SATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich8m_apple_sata] = + { + .flags = PIIX_SATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [piix_pata_vmw] = + { + .flags = PIIX_PATA_FLAGS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ + .udma_mask = ATA_UDMA2, + .port_ops = &piix_vmw_ops, + }, + + /* + * some Sandybridge chipsets have broken 32 mode up to now, + * see https://bugzilla.kernel.org/show_bug.cgi?id=40592 + */ + [ich8_sata_snb] = + { + .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR | PIIX_FLAG_PIO16, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich8_2port_sata_snb] = + { + .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR + | PIIX_FLAG_PIO16, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + + [ich8_2port_sata_byt] = + { + .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR | PIIX_FLAG_PIO16, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, + .port_ops = &piix_sata_ops, + }, + +}; + #define AHCI_PCI_BAR 5 #define AHCI_GLOBAL_CTL 0x04 #define AHCI_ENABLE (1 << 31) @@ -1277,7 +1316,7 @@ static int piix_disable_ahci(struct pci_dev *pdev) * they are found return an error code so we can turn off DMA */ -static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev) +static int piix_check_450nx_errata(struct pci_dev *ata_dev) { struct pci_dev *pdev = NULL; u16 cfg; @@ -1295,14 +1334,16 @@ static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev) no_piix_dma = 2; } if (no_piix_dma) - dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n"); - if (no_piix_dma == 2) - dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n"); + dev_warn(&ata_dev->dev, + "450NX errata present, disabling IDE DMA%s\n", + no_piix_dma == 2 ? " - a BIOS update may resolve this" + : ""); + return no_piix_dma; } -static void __devinit piix_init_pcs(struct ata_host *host, - const struct piix_map_db *map_db) +static void piix_init_pcs(struct ata_host *host, + const struct piix_map_db *map_db) { struct pci_dev *pdev = to_pci_dev(host->dev); u16 pcs, new_pcs; @@ -1318,49 +1359,49 @@ static void __devinit piix_init_pcs(struct ata_host *host, } } -static const int *__devinit piix_init_sata_map(struct pci_dev *pdev, - struct ata_port_info *pinfo, - const struct piix_map_db *map_db) +static const int *piix_init_sata_map(struct pci_dev *pdev, + struct ata_port_info *pinfo, + const struct piix_map_db *map_db) { const int *map; int i, invalid_map = 0; u8 map_value; + char buf[32]; + char *p = buf, *end = buf + sizeof(buf); pci_read_config_byte(pdev, ICH5_PMR, &map_value); map = map_db->map[map_value & map_db->mask]; - dev_printk(KERN_INFO, &pdev->dev, "MAP ["); for (i = 0; i < 4; i++) { switch (map[i]) { case RV: invalid_map = 1; - printk(" XX"); + p += scnprintf(p, end - p, " XX"); break; case NA: - printk(" --"); + p += scnprintf(p, end - p, " --"); break; case IDE: WARN_ON((i & 1) || map[i + 1] != IDE); pinfo[i / 2] = piix_port_info[ich_pata_100]; i++; - printk(" IDE IDE"); + p += scnprintf(p, end - p, " IDE IDE"); break; default: - printk(" P%d", map[i]); + p += scnprintf(p, end - p, " P%d", map[i]); if (i & 1) pinfo[i / 2].flags |= ATA_FLAG_SLAVE_POSS; break; } } - printk(" ]\n"); + dev_info(&pdev->dev, "MAP [%s ]\n", buf); if (invalid_map) - dev_printk(KERN_ERR, &pdev->dev, - "invalid MAP value %u\n", map_value); + dev_err(&pdev->dev, "invalid MAP value %u\n", map_value); return map; } @@ -1390,15 +1431,15 @@ static bool piix_no_sidpr(struct ata_host *host) if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == 0x2920 && pdev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG && pdev->subsystem_device == 0xb049) { - dev_printk(KERN_WARNING, host->dev, - "Samsung DB-P70 detected, disabling SIDPR\n"); + dev_warn(host->dev, + "Samsung DB-P70 detected, disabling SIDPR\n"); return true; } return false; } -static int __devinit piix_init_sidpr(struct ata_host *host) +static int piix_init_sidpr(struct ata_host *host) { struct pci_dev *pdev = to_pci_dev(host->dev); struct piix_host_priv *hpriv = host->private_data; @@ -1443,8 +1484,8 @@ static int __devinit piix_init_sidpr(struct ata_host *host) piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol); if ((scontrol & 0xf00) != 0x300) { - dev_printk(KERN_INFO, host->dev, "SCR access via " - "SIDPR is available but doesn't work\n"); + dev_info(host->dev, + "SCR access via SIDPR is available but doesn't work\n"); return 0; } } @@ -1493,8 +1534,7 @@ static void piix_iocfg_bit18_quirk(struct ata_host *host) * affected systems. */ if (hpriv->saved_iocfg & (1 << 18)) { - dev_printk(KERN_INFO, &pdev->dev, - "applying IOCFG bit18 quirk\n"); + dev_info(&pdev->dev, "applying IOCFG bit18 quirk\n"); pci_write_config_dword(pdev, PIIX_IOCFG, hpriv->saved_iocfg & ~(1 << 18)); } @@ -1535,6 +1575,62 @@ static bool piix_broken_system_poweroff(struct pci_dev *pdev) return false; } +static int prefer_ms_hyperv = 1; +module_param(prefer_ms_hyperv, int, 0); +MODULE_PARM_DESC(prefer_ms_hyperv, + "Prefer Hyper-V paravirtualization drivers instead of ATA, " + "0 - Use ATA drivers, " + "1 (Default) - Use the paravirtualization drivers."); + +static void piix_ignore_devices_quirk(struct ata_host *host) +{ +#if IS_ENABLED(CONFIG_HYPERV_STORAGE) + static const struct dmi_system_id ignore_hyperv[] = { + { + /* On Hyper-V hypervisors the disks are exposed on + * both the emulated SATA controller and on the + * paravirtualised drivers. The CD/DVD devices + * are only exposed on the emulated controller. + * Request we ignore ATA devices on this host. + */ + .ident = "Hyper-V Virtual Machine", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, + "Microsoft Corporation"), + DMI_MATCH(DMI_PRODUCT_NAME, "Virtual Machine"), + }, + }, + { } /* terminate list */ + }; + static const struct dmi_system_id allow_virtual_pc[] = { + { + /* In MS Virtual PC guests the DMI ident is nearly + * identical to a Hyper-V guest. One difference is the + * product version which is used here to identify + * a Virtual PC guest. This entry allows ata_piix to + * drive the emulated hardware. + */ + .ident = "MS Virtual PC 2007", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, + "Microsoft Corporation"), + DMI_MATCH(DMI_PRODUCT_NAME, "Virtual Machine"), + DMI_MATCH(DMI_PRODUCT_VERSION, "VS2005R2"), + }, + }, + { } /* terminate list */ + }; + const struct dmi_system_id *ignore = dmi_first_match(ignore_hyperv); + const struct dmi_system_id *allow = dmi_first_match(allow_virtual_pc); + + if (ignore && !allow && prefer_ms_hyperv) { + host->flags |= ATA_HOST_IGNORE_ATA; + dev_info(host->dev, "%s detected, ATA device ignore set\n", + ignore->ident); + } +#endif +} + /** * piix_init_one - Register PIIX ATA PCI device with kernel services * @pdev: PCI device to register @@ -1550,10 +1646,8 @@ static bool piix_broken_system_poweroff(struct pci_dev *pdev) * Zero on success, or -ERRNO value. */ -static int __devinit piix_init_one(struct pci_dev *pdev, - const struct pci_device_id *ent) +static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { - static int printed_version; struct device *dev = &pdev->dev; struct ata_port_info port_info[2]; const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] }; @@ -1563,9 +1657,7 @@ static int __devinit piix_init_one(struct pci_dev *pdev, struct piix_host_priv *hpriv; int rc; - if (!printed_version++) - dev_printk(KERN_DEBUG, &pdev->dev, - "version " DRV_VERSION "\n"); + ata_print_version_once(&pdev->dev, DRV_VERSION); /* no hotplugging support for later devices (FIXME) */ if (!in_module_init && ent->driver_data >= ich5_sata) @@ -1653,13 +1745,16 @@ static int __devinit piix_init_one(struct pci_dev *pdev, } host->flags |= ATA_HOST_PARALLEL_SCAN; + /* Allow hosts to specify device types to ignore when scanning. */ + piix_ignore_devices_quirk(host); + pci_set_master(pdev); return ata_pci_sff_activate_host(host, ata_bmdma_interrupt, sht); } static void piix_remove_one(struct pci_dev *pdev) { - struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct ata_host *host = pci_get_drvdata(pdev); struct piix_host_priv *hpriv = host->private_data; pci_write_config_dword(pdev, PIIX_IOCFG, hpriv->saved_iocfg); @@ -1667,6 +1762,17 @@ static void piix_remove_one(struct pci_dev *pdev) ata_pci_remove_one(pdev); } +static struct pci_driver piix_pci_driver = { + .name = DRV_NAME, + .id_table = piix_pci_tbl, + .probe = piix_init_one, + .remove = piix_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = piix_pci_device_suspend, + .resume = piix_pci_device_resume, +#endif +}; + static int __init piix_init(void) { int rc; |