1 files changed, 0 insertions, 398 deletions
diff --git a/arch/powerpc/sysdev/commproc.c b/arch/powerpc/sysdev/commproc.c
deleted file mode 100644
index 9b4fafd9a84..00000000000
--- a/arch/powerpc/sysdev/commproc.c
+++ /dev/null
@@ -1,398 +0,0 @@
-/*
- * General Purpose functions for the global management of the
- * Communication Processor Module.
- * Copyright (c) 1997 Dan error_act (dmalek@jlc.net)
- *
- * In addition to the individual control of the communication
- * channels, there are a few functions that globally affect the
- * communication processor.
- *
- * Buffer descriptors must be allocated from the dual ported memory
- * space.  The allocator for that is here.  When the communication
- * process is reset, we reclaim the memory available.  There is
- * currently no deallocator for this memory.
- * The amount of space available is platform dependent.  On the
- * MBX, the EPPC software loads additional microcode into the
- * communication processor, and uses some of the DP ram for this
- * purpose.  Current, the first 512 bytes and the last 256 bytes of
- * memory are used.  Right now I am conservative and only use the
- * memory that can never be used for microcode.  If there are
- * applications that require more DP ram, we can expand the boundaries
- * but then we have to be careful of any downloaded microcode.
- */
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/dma-mapping.h>
-#include <linux/param.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/module.h>
-#include <asm/mpc8xx.h>
-#include <asm/page.h>
-#include <asm/pgtable.h>
-#include <asm/8xx_immap.h>
-#include <asm/commproc.h>
-#include <asm/io.h>
-#include <asm/tlbflush.h>
-#include <asm/rheap.h>
-#include <asm/prom.h>
-
-#include <asm/fs_pd.h>
-
-#define CPM_MAP_SIZE    (0x4000)
-
-static void m8xx_cpm_dpinit(void);
-static	uint	host_buffer;	/* One page of host buffer */
-static	uint	host_end;	/* end + 1 */
-cpm8xx_t	*cpmp;		/* Pointer to comm processor space */
-cpic8xx_t	*cpic_reg;
-
-static struct device_node *cpm_pic_node;
-static struct irq_host *cpm_pic_host;
-
-static void cpm_mask_irq(unsigned int irq)
-{
-	unsigned int cpm_vec = (unsigned int)irq_map[irq].hwirq;
-
-	clrbits32(&cpic_reg->cpic_cimr, (1 << cpm_vec));
-}
-
-static void cpm_unmask_irq(unsigned int irq)
-{
-	unsigned int cpm_vec = (unsigned int)irq_map[irq].hwirq;
-
-	setbits32(&cpic_reg->cpic_cimr, (1 << cpm_vec));
-}
-
-static void cpm_end_irq(unsigned int irq)
-{
-	unsigned int cpm_vec = (unsigned int)irq_map[irq].hwirq;
-
-	out_be32(&cpic_reg->cpic_cisr, (1 << cpm_vec));
-}
-
-static struct irq_chip cpm_pic = {
-	.typename = " CPM PIC ",
-	.mask = cpm_mask_irq,
-	.unmask = cpm_unmask_irq,
-	.eoi = cpm_end_irq,
-};
-
-int cpm_get_irq(void)
-{
-	int cpm_vec;
-
-	/* Get the vector by setting the ACK bit and then reading
-	 * the register.
-	 */
-	out_be16(&cpic_reg->cpic_civr, 1);
-	cpm_vec = in_be16(&cpic_reg->cpic_civr);
-	cpm_vec >>= 11;
-
-	return irq_linear_revmap(cpm_pic_host, cpm_vec);
-}
-
-static int cpm_pic_host_match(struct irq_host *h, struct device_node *node)
-{
-	return cpm_pic_node == node;
-}
-
-static int cpm_pic_host_map(struct irq_host *h, unsigned int virq,
-			  irq_hw_number_t hw)
-{
-	pr_debug("cpm_pic_host_map(%d, 0x%lx)\n", virq, hw);
-
-	get_irq_desc(virq)->status |= IRQ_LEVEL;
-	set_irq_chip_and_handler(virq, &cpm_pic, handle_fasteoi_irq);
-	return 0;
-}
-
-/* The CPM can generate the error interrupt when there is a race condition
- * between generating and masking interrupts.  All we have to do is ACK it
- * and return.  This is a no-op function so we don't need any special
- * tests in the interrupt handler.
- */
-static	irqreturn_t cpm_error_interrupt(int irq, void *dev)
-{
-	return IRQ_HANDLED;
-}
-
-static struct irqaction cpm_error_irqaction = {
-	.handler = cpm_error_interrupt,
-	.mask = CPU_MASK_NONE,
-	.name = "error",
-};
-
-static struct irq_host_ops cpm_pic_host_ops = {
-	.match = cpm_pic_host_match,
-	.map = cpm_pic_host_map,
-};
-
-unsigned int cpm_pic_init(void)
-{
-	struct device_node *np = NULL;
-	struct resource res;
-	unsigned int sirq = NO_IRQ, hwirq, eirq;
-	int ret;
-
-	pr_debug("cpm_pic_init\n");
-
-	np = of_find_compatible_node(NULL, "cpm-pic", "CPM");
-	if (np == NULL) {
-		printk(KERN_ERR "CPM PIC init: can not find cpm-pic node\n");
-		return sirq;
-	}
-	ret = of_address_to_resource(np, 0, &res);
-	if (ret)
-		goto end;
-
-	cpic_reg = (void *)ioremap(res.start, res.end - res.start + 1);
-	if (cpic_reg == NULL)
-		goto end;
-
-	sirq = irq_of_parse_and_map(np, 0);
-	if (sirq == NO_IRQ)
-		goto end;
-
-	/* Initialize the CPM interrupt controller. */
-	hwirq = (unsigned int)irq_map[sirq].hwirq;
-	out_be32(&cpic_reg->cpic_cicr,
-	    (CICR_SCD_SCC4 | CICR_SCC_SCC3 | CICR_SCB_SCC2 | CICR_SCA_SCC1) |
-		((hwirq/2) << 13) | CICR_HP_MASK);
-
-	out_be32(&cpic_reg->cpic_cimr, 0);
-
-	cpm_pic_node = of_node_get(np);
-
-	cpm_pic_host = irq_alloc_host(IRQ_HOST_MAP_LINEAR, 64, &cpm_pic_host_ops, 64);
-	if (cpm_pic_host == NULL) {
-		printk(KERN_ERR "CPM2 PIC: failed to allocate irq host!\n");
-		sirq = NO_IRQ;
-		goto end;
-	}
-	of_node_put(np);
-
-	/* Install our own error handler. */
-	np = of_find_node_by_type(NULL, "cpm");
-	if (np == NULL) {
-		printk(KERN_ERR "CPM PIC init: can not find cpm node\n");
-		goto end;
-	}
-	eirq= irq_of_parse_and_map(np, 0);
-	if (eirq == NO_IRQ)
-		goto end;
-
-	if (setup_irq(eirq, &cpm_error_irqaction))
-		printk(KERN_ERR "Could not allocate CPM error IRQ!");
-
-	setbits32(&cpic_reg->cpic_cicr, CICR_IEN);
-
-end:
-	of_node_put(np);
-	return sirq;
-}
-
-void cpm_reset(void)
-{
-	cpm8xx_t	*commproc;
-	sysconf8xx_t    *siu_conf;
-
-	commproc = (cpm8xx_t *)ioremap(CPM_MAP_ADDR, CPM_MAP_SIZE);
-
-#ifdef CONFIG_UCODE_PATCH
-	/* Perform a reset.
-	*/
-	out_be16(&commproc->cp_cpcr,  CPM_CR_RST | CPM_CR_FLG);
-
-	/* Wait for it.
-	*/
-	while (in_be16(&commproc->cp_cpcr) & CPM_CR_FLG);
-
-	cpm_load_patch(commproc);
-#endif
-
-	/* Set SDMA Bus Request priority 5.
-	 * On 860T, this also enables FEC priority 6.  I am not sure
-	 * this is what we realy want for some applications, but the
-	 * manual recommends it.
-	 * Bit 25, FAM can also be set to use FEC aggressive mode (860T).
-	 */
-	siu_conf = (sysconf8xx_t*)immr_map(im_siu_conf);
-	out_be32(&siu_conf->sc_sdcr, 1);
-	immr_unmap(siu_conf);
-
-	/* Reclaim the DP memory for our use. */
-	m8xx_cpm_dpinit();
-
-	/* Tell everyone where the comm processor resides.
-	*/
-	cpmp = commproc;
-}
-
-/* We used to do this earlier, but have to postpone as long as possible
- * to ensure the kernel VM is now running.
- */
-static void
-alloc_host_memory(void)
-{
-	dma_addr_t	physaddr;
-
-	/* Set the host page for allocation.
-	*/
-	host_buffer = (uint)dma_alloc_coherent(NULL, PAGE_SIZE, &physaddr,
-			GFP_KERNEL);
-	host_end = host_buffer + PAGE_SIZE;
-}
-
-/* We also own one page of host buffer space for the allocation of
- * UART "fifos" and the like.
- */
-uint
-m8xx_cpm_hostalloc(uint size)
-{
-	uint	retloc;
-
-	if (host_buffer == 0)
-		alloc_host_memory();
-
-	if ((host_buffer + size) >= host_end)
-		return(0);
-
-	retloc = host_buffer;
-	host_buffer += size;
-
-	return(retloc);
-}
-
-/* Set a baud rate generator.  This needs lots of work.  There are
- * four BRGs, any of which can be wired to any channel.
- * The internal baud rate clock is the system clock divided by 16.
- * This assumes the baudrate is 16x oversampled by the uart.
- */
-#define BRG_INT_CLK		(get_brgfreq())
-#define BRG_UART_CLK		(BRG_INT_CLK/16)
-#define BRG_UART_CLK_DIV16	(BRG_UART_CLK/16)
-
-void
-cpm_setbrg(uint brg, uint rate)
-{
-	volatile uint	*bp;
-
-	/* This is good enough to get SMCs running.....
-	*/
-	bp = (uint *)&cpmp->cp_brgc1;
-	bp += brg;
-	/* The BRG has a 12-bit counter.  For really slow baud rates (or
-	 * really fast processors), we may have to further divide by 16.
-	 */
-	if (((BRG_UART_CLK / rate) - 1) < 4096)
-		*bp = (((BRG_UART_CLK / rate) - 1) << 1) | CPM_BRG_EN;
-	else
-		*bp = (((BRG_UART_CLK_DIV16 / rate) - 1) << 1) |
-						CPM_BRG_EN | CPM_BRG_DIV16;
-}
-
-/*
- * dpalloc / dpfree bits.
- */
-static spinlock_t cpm_dpmem_lock;
-/*
- * 16 blocks should be enough to satisfy all requests
- * until the memory subsystem goes up...
- */
-static rh_block_t cpm_boot_dpmem_rh_block[16];
-static rh_info_t cpm_dpmem_info;
-
-#define CPM_DPMEM_ALIGNMENT	8
-static u8* dpram_vbase;
-static uint dpram_pbase;
-
-void m8xx_cpm_dpinit(void)
-{
-	spin_lock_init(&cpm_dpmem_lock);
-
-	dpram_vbase = immr_map_size(im_cpm.cp_dpmem, CPM_DATAONLY_BASE + CPM_DATAONLY_SIZE);
-	dpram_pbase = (uint)&((immap_t *)IMAP_ADDR)->im_cpm.cp_dpmem;
-
-	/* Initialize the info header */
-	rh_init(&cpm_dpmem_info, CPM_DPMEM_ALIGNMENT,
-			sizeof(cpm_boot_dpmem_rh_block) /
-			sizeof(cpm_boot_dpmem_rh_block[0]),
-			cpm_boot_dpmem_rh_block);
-
-	/*
-	 * Attach the usable dpmem area.
-	 * XXX: This is actually crap.  CPM_DATAONLY_BASE and
-	 * CPM_DATAONLY_SIZE are a subset of the available dparm.  It varies
-	 * with the processor and the microcode patches applied / activated.
-	 * But the following should be at least safe.
-	 */
-	rh_attach_region(&cpm_dpmem_info, (void *)CPM_DATAONLY_BASE, CPM_DATAONLY_SIZE);
-}
-
-/*
- * Allocate the requested size worth of DP memory.
- * This function returns an offset into the DPRAM area.
- * Use cpm_dpram_addr() to get the virtual address of the area.
- */
-uint cpm_dpalloc(uint size, uint align)
-{
-	void *start;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cpm_dpmem_lock, flags);
-	cpm_dpmem_info.alignment = align;
-	start = rh_alloc(&cpm_dpmem_info, size, "commproc");
-	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
-	return (uint)start;
-}
-EXPORT_SYMBOL(cpm_dpalloc);
-
-int cpm_dpfree(uint offset)
-{
-	int ret;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cpm_dpmem_lock, flags);
-	ret = rh_free(&cpm_dpmem_info, (void *)offset);
-	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
-	return ret;
-}
-EXPORT_SYMBOL(cpm_dpfree);
-
-uint cpm_dpalloc_fixed(uint offset, uint size, uint align)
-{
-	void *start;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cpm_dpmem_lock, flags);
-	cpm_dpmem_info.alignment = align;
-	start = rh_alloc_fixed(&cpm_dpmem_info, (void *)offset, size, "commproc");
-	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
-	return (uint)start;
-}
-EXPORT_SYMBOL(cpm_dpalloc_fixed);
-
-void cpm_dpdump(void)
-{
-	rh_dump(&cpm_dpmem_info);
-}
-EXPORT_SYMBOL(cpm_dpdump);
-
-void *cpm_dpram_addr(uint offset)
-{
-	return (void *)(dpram_vbase + offset);
-}
-EXPORT_SYMBOL(cpm_dpram_addr);
-
-uint cpm_dpram_phys(u8* addr)
-{
-	return (dpram_pbase + (uint)(addr - dpram_vbase));
-}
-EXPORT_SYMBOL(cpm_dpram_addr);