diff options
Diffstat (limited to 'arch/mips/sibyte')
22 files changed, 398 insertions, 473 deletions
diff --git a/arch/mips/sibyte/Kconfig b/arch/mips/sibyte/Kconfig index 366b19d33f7..5fbd3605d24 100644 --- a/arch/mips/sibyte/Kconfig +++ b/arch/mips/sibyte/Kconfig @@ -71,10 +71,11 @@ config SIBYTE_SB1xxx_SOC bool select DMA_COHERENT select IRQ_CPU - select SIBYTE_CFE select SWAP_IO_SPACE select SYS_SUPPORTS_32BIT_KERNEL select SYS_SUPPORTS_64BIT_KERNEL + select FW_CFE + select SYS_HAS_EARLY_PRINTK choice prompt "SiByte SOC Stepping" @@ -128,13 +129,6 @@ config SIBYTE_ENABLE_LDT_IF_PCI bool select SIBYTE_HAS_LDT if PCI -config SIMULATION - bool "Running under simulation" - depends on SIBYTE_SB1xxx_SOC - help - Build a kernel suitable for running under the GDB simulator. - Primarily adjusts the kernel's notion of time. - config SB1_CEX_ALWAYS_FATAL bool "All cache exceptions considered fatal (no recovery attempted)" depends on SIBYTE_SB1xxx_SOC @@ -143,37 +137,18 @@ config SB1_CERR_STALL bool "Stall (rather than panic) on fatal cache error" depends on SIBYTE_SB1xxx_SOC -config SIBYTE_CFE - bool "Booting from CFE" - depends on SIBYTE_SB1xxx_SOC - select CFE - select SYS_HAS_EARLY_PRINTK - help - Make use of the CFE API for enumerating available memory, - controlling secondary CPUs, and possibly console output. - config SIBYTE_CFE_CONSOLE bool "Use firmware console" - depends on SIBYTE_CFE + depends on SIBYTE_SB1xxx_SOC help Use the CFE API's console write routines during boot. Other console options (VT console, sb1250 duart console, etc.) should not be configured. -config SIBYTE_STANDALONE - bool - depends on SIBYTE_SB1xxx_SOC && !SIBYTE_CFE - select SYS_HAS_EARLY_PRINTK - default y - -config SIBYTE_STANDALONE_RAM_SIZE - int "Memory size (in megabytes)" - depends on SIBYTE_STANDALONE - default "32" - config SIBYTE_BUS_WATCHER bool "Support for Bus Watcher statistics" - depends on SIBYTE_SB1xxx_SOC + depends on SIBYTE_SB1xxx_SOC && \ + (SIBYTE_BCM112X || SIBYTE_SB1250) help Handle and keep statistics on the bus error interrupts (COR_ECC, BAD_ECC, IO_BUS). diff --git a/arch/mips/sibyte/Makefile b/arch/mips/sibyte/Makefile new file mode 100644 index 00000000000..c8ed2c807e6 --- /dev/null +++ b/arch/mips/sibyte/Makefile @@ -0,0 +1,27 @@ +# +# Sibyte SB1250 / BCM1480 family of SOCs +# +obj-$(CONFIG_SIBYTE_BCM112X) += sb1250/ +obj-$(CONFIG_SIBYTE_BCM112X) += common/ +obj-$(CONFIG_SIBYTE_SB1250) += sb1250/ +obj-$(CONFIG_SIBYTE_SB1250) += common/ +obj-$(CONFIG_SIBYTE_BCM1x55) += bcm1480/ +obj-$(CONFIG_SIBYTE_BCM1x55) += common/ +obj-$(CONFIG_SIBYTE_BCM1x80) += bcm1480/ +obj-$(CONFIG_SIBYTE_BCM1x80) += common/ + +# +# Sibyte BCM91120x (Carmel) board +# Sibyte BCM91120C (CRhine) board +# Sibyte BCM91125C (CRhone) board +# Sibyte BCM91125E (Rhone) board +# Sibyte SWARM board +# Sibyte BCM91x80 (BigSur) board +# +obj-$(CONFIG_SIBYTE_CARMEL) += swarm/ +obj-$(CONFIG_SIBYTE_CRHINE) += swarm/ +obj-$(CONFIG_SIBYTE_CRHONE) += swarm/ +obj-$(CONFIG_SIBYTE_RHONE) += swarm/ +obj-$(CONFIG_SIBYTE_SENTOSA) += swarm/ +obj-$(CONFIG_SIBYTE_SWARM) += swarm/ +obj-$(CONFIG_SIBYTE_BIGSUR) += swarm/ diff --git a/arch/mips/sibyte/Platform b/arch/mips/sibyte/Platform new file mode 100644 index 00000000000..af117330ce1 --- /dev/null +++ b/arch/mips/sibyte/Platform @@ -0,0 +1,44 @@ +# +# These are all rather similar so we consider them a single platform +# +platform-$(CONFIG_SIBYTE_BCM112X) += sibyte/ +platform-$(CONFIG_SIBYTE_SB1250) += sibyte/ +platform-$(CONFIG_SIBYTE_BCM1x55) += sibyte/ +platform-$(CONFIG_SIBYTE_BCM1x80) += sibyte/ + +# +# Sibyte SB1250 / BCM1480 family of SOCs +# +cflags-$(CONFIG_SIBYTE_BCM112X) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL + +cflags-$(CONFIG_SIBYTE_SB1250) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL + +cflags-$(CONFIG_SIBYTE_BCM1x55) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL + +cflags-$(CONFIG_SIBYTE_BCM1x80) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL + +# +# Sibyte BCM91120x (Carmel) board +# Sibyte BCM91120C (CRhine) board +# Sibyte BCM91125C (CRhone) board +# Sibyte BCM91125E (Rhone) board +# Sibyte BCM91250A (SWARM) board +# Sibyte BCM91250C2 (LittleSur) board +# Sibyte BCM91x80 (BigSur) board +# +load-$(CONFIG_SIBYTE_CARMEL) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_CRHINE) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_CRHONE) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_RHONE) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_SENTOSA) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_SWARM) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_BIGSUR) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_LITTLESUR) := 0xffffffff80100000 diff --git a/arch/mips/sibyte/bcm1480/Makefile b/arch/mips/sibyte/bcm1480/Makefile index f292f7df0cf..cdc4c56c3e2 100644 --- a/arch/mips/sibyte/bcm1480/Makefile +++ b/arch/mips/sibyte/bcm1480/Makefile @@ -1,5 +1,3 @@ obj-y := setup.o irq.o time.o obj-$(CONFIG_SMP) += smp.o - -EXTRA_CFLAGS += -Werror diff --git a/arch/mips/sibyte/bcm1480/irq.c b/arch/mips/sibyte/bcm1480/irq.c index 690de06bde9..373fbbc8425 100644 --- a/arch/mips/sibyte/bcm1480/irq.c +++ b/arch/mips/sibyte/bcm1480/irq.c @@ -19,15 +19,14 @@ #include <linux/init.h> #include <linux/linkage.h> #include <linux/interrupt.h> +#include <linux/smp.h> #include <linux/spinlock.h> #include <linux/mm.h> -#include <linux/slab.h> #include <linux/kernel_stat.h> #include <asm/errno.h> #include <asm/irq_regs.h> #include <asm/signal.h> -#include <asm/system.h> #include <asm/io.h> #include <asm/sibyte/bcm1480_regs.h> @@ -44,42 +43,21 @@ * for interrupt lines */ - -static void end_bcm1480_irq(unsigned int irq); -static void enable_bcm1480_irq(unsigned int irq); -static void disable_bcm1480_irq(unsigned int irq); -static void ack_bcm1480_irq(unsigned int irq); -#ifdef CONFIG_SMP -static int bcm1480_set_affinity(unsigned int irq, const struct cpumask *mask); -#endif - #ifdef CONFIG_PCI extern unsigned long ht_eoi_space; #endif -static struct irq_chip bcm1480_irq_type = { - .name = "BCM1480-IMR", - .ack = ack_bcm1480_irq, - .mask = disable_bcm1480_irq, - .mask_ack = ack_bcm1480_irq, - .unmask = enable_bcm1480_irq, - .end = end_bcm1480_irq, -#ifdef CONFIG_SMP - .set_affinity = bcm1480_set_affinity -#endif -}; - /* Store the CPU id (not the logical number) */ int bcm1480_irq_owner[BCM1480_NR_IRQS]; -DEFINE_SPINLOCK(bcm1480_imr_lock); +static DEFINE_RAW_SPINLOCK(bcm1480_imr_lock); void bcm1480_mask_irq(int cpu, int irq) { unsigned long flags, hl_spacing; u64 cur_ints; - spin_lock_irqsave(&bcm1480_imr_lock, flags); + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); hl_spacing = 0; if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) { hl_spacing = BCM1480_IMR_HL_SPACING; @@ -88,7 +66,7 @@ void bcm1480_mask_irq(int cpu, int irq) cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); cur_ints |= (((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); - spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); } void bcm1480_unmask_irq(int cpu, int irq) @@ -96,7 +74,7 @@ void bcm1480_unmask_irq(int cpu, int irq) unsigned long flags, hl_spacing; u64 cur_ints; - spin_lock_irqsave(&bcm1480_imr_lock, flags); + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); hl_spacing = 0; if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) { hl_spacing = BCM1480_IMR_HL_SPACING; @@ -105,28 +83,25 @@ void bcm1480_unmask_irq(int cpu, int irq) cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); cur_ints &= ~(((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); - spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); } #ifdef CONFIG_SMP -static int bcm1480_set_affinity(unsigned int irq, const struct cpumask *mask) +static int bcm1480_set_affinity(struct irq_data *d, const struct cpumask *mask, + bool force) { + unsigned int irq_dirty, irq = d->irq; int i = 0, old_cpu, cpu, int_on, k; u64 cur_ints; unsigned long flags; - unsigned int irq_dirty; - if (cpumask_weight(mask) != 1) { - printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq); - return -1; - } - i = cpumask_first(mask); + i = cpumask_first_and(mask, cpu_online_mask); /* Convert logical CPU to physical CPU */ cpu = cpu_logical_map(i); /* Protect against other affinity changers and IMR manipulation */ - spin_lock_irqsave(&bcm1480_imr_lock, flags); + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); /* Swizzle each CPU's IMR (but leave the IP selection alone) */ old_cpu = bcm1480_irq_owner[irq]; @@ -151,7 +126,7 @@ static int bcm1480_set_affinity(unsigned int irq, const struct cpumask *mask) ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING))); } } - spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); return 0; } @@ -160,21 +135,25 @@ static int bcm1480_set_affinity(unsigned int irq, const struct cpumask *mask) /*****************************************************************************/ -static void disable_bcm1480_irq(unsigned int irq) +static void disable_bcm1480_irq(struct irq_data *d) { + unsigned int irq = d->irq; + bcm1480_mask_irq(bcm1480_irq_owner[irq], irq); } -static void enable_bcm1480_irq(unsigned int irq) +static void enable_bcm1480_irq(struct irq_data *d) { + unsigned int irq = d->irq; + bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq); } -static void ack_bcm1480_irq(unsigned int irq) +static void ack_bcm1480_irq(struct irq_data *d) { + unsigned int irq_dirty, irq = d->irq; u64 pending; - unsigned int irq_dirty; int k; /* @@ -221,21 +200,23 @@ static void ack_bcm1480_irq(unsigned int irq) bcm1480_mask_irq(bcm1480_irq_owner[irq], irq); } - -static void end_bcm1480_irq(unsigned int irq) -{ - if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) { - bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq); - } -} - +static struct irq_chip bcm1480_irq_type = { + .name = "BCM1480-IMR", + .irq_mask_ack = ack_bcm1480_irq, + .irq_mask = disable_bcm1480_irq, + .irq_unmask = enable_bcm1480_irq, +#ifdef CONFIG_SMP + .irq_set_affinity = bcm1480_set_affinity +#endif +}; void __init init_bcm1480_irqs(void) { int i; for (i = 0; i < BCM1480_NR_IRQS; i++) { - set_irq_chip_and_handler(i, &bcm1480_irq_type, handle_level_irq); + irq_set_chip_and_handler(i, &bcm1480_irq_type, + handle_level_irq); bcm1480_irq_owner[i] = 0; } } @@ -257,7 +238,7 @@ void __init init_bcm1480_irqs(void) * On the second cpu, everything is set to IP5, which is * ignored, EXCEPT the mailbox interrupt. That one is * set to IP[2] so it is handled. This is needed so we - * can do cross-cpu function calls, as requred by SMP + * can do cross-cpu function calls, as required by SMP */ #define IMR_IP2_VAL K_BCM1480_INT_MAP_I0 @@ -302,10 +283,10 @@ void __init arch_init_irq(void) for (cpu = 0; cpu < 4; cpu++) { __raw_writeq(IMR_IP3_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (K_BCM1480_INT_MBOX_0_0 << 3))); - } + } - /* Clear the mailboxes. The firmware may leave them dirty */ + /* Clear the mailboxes. The firmware may leave them dirty */ for (cpu = 0; cpu < 4; cpu++) { __raw_writeq(0xffffffffffffffffULL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_0_CLR_CPU))); @@ -326,7 +307,7 @@ void __init arch_init_irq(void) /* * Note that the timer interrupts are also mapped, but this is - * done in bcm1480_time_init(). Also, the profiling driver + * done in bcm1480_time_init(). Also, the profiling driver * does its own management of IP7. */ @@ -344,7 +325,7 @@ static inline void dispatch_ip2(void) /* * Default...we've hit an IP[2] interrupt, which means we've got to - * check the 1480 interrupt registers to figure out what to do. Need + * check the 1480 interrupt registers to figure out what to do. Need * to detect which CPU we're on, now that smp_affinity is supported. */ base = A_BCM1480_IMR_MAPPER(cpu); @@ -366,19 +347,8 @@ asmlinkage void plat_irq_dispatch(void) unsigned int cpu = smp_processor_id(); unsigned int pending; -#ifdef CONFIG_SIBYTE_BCM1480_PROF - /* Set compare to count to silence count/compare timer interrupts */ - write_c0_compare(read_c0_count()); -#endif - pending = read_c0_cause() & read_c0_status(); -#ifdef CONFIG_SIBYTE_BCM1480_PROF - if (pending & CAUSEF_IP7) /* Cpu performance counter interrupt */ - sbprof_cpu_intr(); - else -#endif - if (pending & CAUSEF_IP4) do_IRQ(K_BCM1480_INT_TIMER_0 + cpu); #ifdef CONFIG_SMP diff --git a/arch/mips/sibyte/bcm1480/setup.c b/arch/mips/sibyte/bcm1480/setup.c index 05ed92c92b6..8e2e04f7787 100644 --- a/arch/mips/sibyte/bcm1480/setup.c +++ b/arch/mips/sibyte/bcm1480/setup.c @@ -22,6 +22,7 @@ #include <linux/string.h> #include <asm/bootinfo.h> +#include <asm/cpu.h> #include <asm/mipsregs.h> #include <asm/io.h> #include <asm/sibyte/sb1250.h> @@ -119,7 +120,7 @@ void __init bcm1480_setup(void) uint64_t sys_rev; int plldiv; - sb1_pass = read_c0_prid() & 0xff; + sb1_pass = read_c0_prid() & PRID_REV_MASK; sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION)); soc_type = SYS_SOC_TYPE(sys_rev); part_type = G_SYS_PART(sys_rev); diff --git a/arch/mips/sibyte/bcm1480/smp.c b/arch/mips/sibyte/bcm1480/smp.c index 314691648c9..af7d44edd9a 100644 --- a/arch/mips/sibyte/bcm1480/smp.c +++ b/arch/mips/sibyte/bcm1480/smp.c @@ -20,6 +20,7 @@ #include <linux/delay.h> #include <linux/smp.h> #include <linux/kernel_stat.h> +#include <linux/sched.h> #include <asm/mmu_context.h> #include <asm/io.h> @@ -59,7 +60,7 @@ static void *mailbox_0_regs[] = { /* * SMP init and finish on secondary CPUs */ -void __cpuinit bcm1480_smp_init(void) +void bcm1480_smp_init(void) { unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 | STATUSF_IP1 | STATUSF_IP0; @@ -82,18 +83,19 @@ static void bcm1480_send_ipi_single(int cpu, unsigned int action) __raw_writeq((((u64)action)<< 48), mailbox_0_set_regs[cpu]); } -static void bcm1480_send_ipi_mask(cpumask_t mask, unsigned int action) +static void bcm1480_send_ipi_mask(const struct cpumask *mask, + unsigned int action) { unsigned int i; - for_each_cpu_mask(i, mask) + for_each_cpu(i, mask) bcm1480_send_ipi_single(i, action); } /* * Code to run on secondary just after probing the CPU */ -static void __cpuinit bcm1480_init_secondary(void) +static void bcm1480_init_secondary(void) { extern void bcm1480_smp_init(void); @@ -104,7 +106,7 @@ static void __cpuinit bcm1480_init_secondary(void) * Do any tidying up before marking online and running the idle * loop */ -static void __cpuinit bcm1480_smp_finish(void) +static void bcm1480_smp_finish(void) { extern void sb1480_clockevent_init(void); @@ -113,17 +115,10 @@ static void __cpuinit bcm1480_smp_finish(void) } /* - * Final cleanup after all secondaries booted - */ -static void bcm1480_cpus_done(void) -{ -} - -/* * Setup the PC, SP, and GP of a secondary processor and start it * running! */ -static void __cpuinit bcm1480_boot_secondary(int cpu, struct task_struct *idle) +static void bcm1480_boot_secondary(int cpu, struct task_struct *idle) { int retval; @@ -136,7 +131,7 @@ static void __cpuinit bcm1480_boot_secondary(int cpu, struct task_struct *idle) /* * Use CFE to find out how many CPUs are available, setting up - * cpu_possible_map and the logical/physical mappings. + * cpu_possible_mask and the logical/physical mappings. * XXXKW will the boot CPU ever not be physical 0? * * Common setup before any secondaries are started @@ -145,14 +140,13 @@ static void __init bcm1480_smp_setup(void) { int i, num; - cpus_clear(cpu_possible_map); - cpu_set(0, cpu_possible_map); + init_cpu_possible(cpumask_of(0)); __cpu_number_map[0] = 0; __cpu_logical_map[0] = 0; for (i = 1, num = 0; i < NR_CPUS; i++) { if (cfe_cpu_stop(i) == 0) { - cpu_set(i, cpu_possible_map); + set_cpu_possible(i, true); __cpu_number_map[i] = ++num; __cpu_logical_map[num] = i; } @@ -169,7 +163,6 @@ struct plat_smp_ops bcm1480_smp_ops = { .send_ipi_mask = bcm1480_send_ipi_mask, .init_secondary = bcm1480_init_secondary, .smp_finish = bcm1480_smp_finish, - .cpus_done = bcm1480_cpus_done, .boot_secondary = bcm1480_boot_secondary, .smp_setup = bcm1480_smp_setup, .prepare_cpus = bcm1480_prepare_cpus, @@ -181,17 +174,15 @@ void bcm1480_mailbox_interrupt(void) int irq = K_BCM1480_INT_MBOX_0_0; unsigned int action; - kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq)); + kstat_incr_irq_this_cpu(irq); /* Load the mailbox register to figure out what we're supposed to do */ action = (__raw_readq(mailbox_0_regs[cpu]) >> 48) & 0xffff; /* Clear the mailbox to clear the interrupt */ __raw_writeq(((u64)action)<<48, mailbox_0_clear_regs[cpu]); - /* - * Nothing to do for SMP_RESCHEDULE_YOURSELF; returning from the - * interrupt will do the reschedule for us - */ + if (action & SMP_RESCHEDULE_YOURSELF) + scheduler_ipi(); if (action & SMP_CALL_FUNCTION) smp_call_function_interrupt(); diff --git a/arch/mips/sibyte/cfe/Makefile b/arch/mips/sibyte/cfe/Makefile deleted file mode 100644 index 02b32e142ad..00000000000 --- a/arch/mips/sibyte/cfe/Makefile +++ /dev/null @@ -1,2 +0,0 @@ -lib-y = setup.o -lib-$(CONFIG_SIBYTE_CFE_CONSOLE) += console.o diff --git a/arch/mips/sibyte/common/Makefile b/arch/mips/sibyte/common/Makefile index 48a91b9e587..b3d6bf23a66 100644 --- a/arch/mips/sibyte/common/Makefile +++ b/arch/mips/sibyte/common/Makefile @@ -1,5 +1,4 @@ -obj-y := - +obj-y := cfe.o +obj-$(CONFIG_SIBYTE_BUS_WATCHER) += bus_watcher.o +obj-$(CONFIG_SIBYTE_CFE_CONSOLE) += cfe_console.o obj-$(CONFIG_SIBYTE_TBPROF) += sb_tbprof.o - -EXTRA_CFLAGS += -Werror diff --git a/arch/mips/sibyte/sb1250/bus_watcher.c b/arch/mips/sibyte/common/bus_watcher.c index 45274bd3cd8..5581844c919 100644 --- a/arch/mips/sibyte/sb1250/bus_watcher.c +++ b/arch/mips/sibyte/common/bus_watcher.c @@ -30,13 +30,16 @@ #include <linux/interrupt.h> #include <linux/sched.h> #include <linux/proc_fs.h> -#include <asm/system.h> +#include <linux/seq_file.h> #include <asm/io.h> #include <asm/sibyte/sb1250.h> #include <asm/sibyte/sb1250_regs.h> #include <asm/sibyte/sb1250_int.h> #include <asm/sibyte/sb1250_scd.h> +#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) +#include <asm/sibyte/bcm1480_regs.h> +#endif struct bw_stats_struct { @@ -72,7 +75,7 @@ static void print_summary(uint32_t status, uint32_t l2_err, * already been destructively read out of the registers. * * notes: this is currently used by the cache error handler - * should provide locking against the interrupt handler + * should provide locking against the interrupt handler */ void check_bus_watcher(void) { @@ -81,9 +84,15 @@ void check_bus_watcher(void) #ifdef CONFIG_SB1_PASS_1_WORKAROUNDS /* Destructive read, clears register and interrupt */ status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS)); -#else +#elif defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250) /* Use non-destructive register */ status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS_DEBUG)); +#elif defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) + /* Use non-destructive register */ + /* Same as 1250 except BUS_ERR_STATUS_DEBUG is in a different place. */ + status = csr_in32(IOADDR(A_BCM1480_BUS_ERR_STATUS_DEBUG)); +#else +#error bus watcher being built for unknown Sibyte SOC! #endif if (!(status & 0x7fffffff)) { printk("Using last values reaped by bus watcher driver\n"); @@ -100,63 +109,60 @@ void check_bus_watcher(void) printk("Bus watcher indicates no error\n"); } -static int bw_print_buffer(char *page, struct bw_stats_struct *stats) +#ifdef CONFIG_PROC_FS + +/* For simplicity, I want to assume a single read is required each + time */ +static int bw_proc_show(struct seq_file *m, void *v) { - int len; - - len = sprintf(page, "SiByte Bus Watcher statistics\n"); - len += sprintf(page+len, "-----------------------------\n"); - len += sprintf(page+len, "L2-d-cor %8ld\nL2-d-bad %8ld\n", - stats->l2_cor_d, stats->l2_bad_d); - len += sprintf(page+len, "L2-t-cor %8ld\nL2-t-bad %8ld\n", - stats->l2_cor_t, stats->l2_bad_t); - len += sprintf(page+len, "MC-d-cor %8ld\nMC-d-bad %8ld\n", - stats->mem_cor_d, stats->mem_bad_d); - len += sprintf(page+len, "IO-err %8ld\n", stats->bus_error); - len += sprintf(page+len, "\nLast recorded signature:\n"); - len += sprintf(page+len, "Request %02x from %d, answered by %d with Dcode %d\n", - (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f), - (int)(G_SCD_BERR_TID(stats->status) >> 6), - (int)G_SCD_BERR_RID(stats->status), - (int)G_SCD_BERR_DCODE(stats->status)); + struct bw_stats_struct *stats = m->private; + + seq_puts(m, "SiByte Bus Watcher statistics\n"); + seq_puts(m, "-----------------------------\n"); + seq_printf(m, "L2-d-cor %8ld\nL2-d-bad %8ld\n", + stats->l2_cor_d, stats->l2_bad_d); + seq_printf(m, "L2-t-cor %8ld\nL2-t-bad %8ld\n", + stats->l2_cor_t, stats->l2_bad_t); + seq_printf(m, "MC-d-cor %8ld\nMC-d-bad %8ld\n", + stats->mem_cor_d, stats->mem_bad_d); + seq_printf(m, "IO-err %8ld\n", stats->bus_error); + seq_puts(m, "\nLast recorded signature:\n"); + seq_printf(m, "Request %02x from %d, answered by %d with Dcode %d\n", + (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f), + (int)(G_SCD_BERR_TID(stats->status) >> 6), + (int)G_SCD_BERR_RID(stats->status), + (int)G_SCD_BERR_DCODE(stats->status)); /* XXXKW indicate multiple errors between printings, or stats - collection (or both)? */ + collection (or both)? */ if (stats->status & M_SCD_BERR_MULTERRS) - len += sprintf(page+len, "Multiple errors observed since last check.\n"); + seq_puts(m, "Multiple errors observed since last check.\n"); if (stats->status_printed) { - len += sprintf(page+len, "(no change since last printing)\n"); + seq_puts(m, "(no change since last printing)\n"); } else { stats->status_printed = 1; } - return len; + return 0; } -#ifdef CONFIG_PROC_FS - -/* For simplicity, I want to assume a single read is required each - time */ -static int bw_read_proc(char *page, char **start, off_t off, - int count, int *eof, void *data) +static int bw_proc_open(struct inode *inode, struct file *file) { - int len; - - if (off == 0) { - len = bw_print_buffer(page, data); - *start = page; - } else { - len = 0; - *eof = 1; - } - return len; + return single_open(file, bw_proc_show, PDE_DATA(inode)); } +static const struct file_operations bw_proc_fops = { + .open = bw_proc_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; + static void create_proc_decoder(struct bw_stats_struct *stats) { struct proc_dir_entry *ent; - ent = create_proc_read_entry("bus_watcher", S_IWUSR | S_IRUGO, NULL, - bw_read_proc, stats); + ent = proc_create_data("bus_watcher", S_IWUSR | S_IRUGO, NULL, + &bw_proc_fops, stats); if (!ent) { printk(KERN_INFO "Unable to initialize bus_watcher /proc entry\n"); return; @@ -169,7 +175,7 @@ static void create_proc_decoder(struct bw_stats_struct *stats) * sibyte_bw_int - handle bus watcher interrupts and accumulate counts * * notes: possible re-entry due to multiple sources - * should check/indicate saturation + * should check/indicate saturation */ static irqreturn_t sibyte_bw_int(int irq, void *data) { @@ -178,9 +184,6 @@ static irqreturn_t sibyte_bw_int(int irq, void *data) #ifdef CONFIG_SIBYTE_BW_TRACE int i; #endif -#ifndef CONFIG_PROC_FS - char bw_buf[1024]; -#endif #ifdef CONFIG_SIBYTE_BW_TRACE csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG)); @@ -211,11 +214,6 @@ static irqreturn_t sibyte_bw_int(int irq, void *data) stats->bus_error += G_SCD_MEM_BUSERR(cntr); csr_out32(0, IOADDR(A_BUS_MEM_IO_ERRORS)); -#ifndef CONFIG_PROC_FS - bw_print_buffer(bw_buf, stats); - printk(bw_buf); -#endif - return IRQ_HANDLED; } diff --git a/arch/mips/sibyte/cfe/setup.c b/arch/mips/sibyte/common/cfe.c index eb5396cf81b..588e1806a1a 100644 --- a/arch/mips/sibyte/cfe/setup.c +++ b/arch/mips/sibyte/common/cfe.c @@ -127,8 +127,8 @@ static __init void prom_meminit(void) if ((initrd_pstart > addr) && (initrd_pstart < (addr + size))) { add_memory_region(addr, - initrd_pstart - addr, - BOOT_MEM_RAM); + initrd_pstart - addr, + BOOT_MEM_RAM); rd_flag = 1; } if ((initrd_pend > addr) && @@ -195,7 +195,7 @@ static int __init initrd_setup(char *str) /* *Initrd location comes in the form "<hex size of ramdisk in bytes>@<location in memory>" - * e.g. initrd=3abfd@80010000. This is set up by the loader. + * e.g. initrd=3abfd@80010000. This is set up by the loader. */ for (tmp = str; *tmp != '@'; tmp++) { if (!*tmp) { @@ -244,7 +244,7 @@ void __init prom_init(void) int *prom_vec = (int *) fw_arg3; _machine_restart = cfe_linux_restart; - _machine_halt = cfe_linux_halt; + _machine_halt = cfe_linux_halt; pm_power_off = cfe_linux_halt; /* @@ -287,7 +287,7 @@ void __init prom_init(void) * boot console */ cfe_cons_handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE); - if (cfe_getenv("LINUX_CMDLINE", arcs_cmdline, CL_SIZE) < 0) { + if (cfe_getenv("LINUX_CMDLINE", arcs_cmdline, COMMAND_LINE_SIZE) < 0) { if (argc >= 0) { /* The loader should have set the command line */ /* too early for panic to do any good */ @@ -299,7 +299,7 @@ void __init prom_init(void) #ifdef CONFIG_BLK_DEV_INITRD { char *ptr; - /* Need to find out early whether we've got an initrd. So scan + /* Need to find out early whether we've got an initrd. So scan the list looking now */ for (ptr = arcs_cmdline; *ptr; ptr++) { while (*ptr == ' ') { @@ -318,7 +318,7 @@ void __init prom_init(void) #endif /* CONFIG_BLK_DEV_INITRD */ /* Not sure this is needed, but it's the safe way. */ - arcs_cmdline[CL_SIZE-1] = 0; + arcs_cmdline[COMMAND_LINE_SIZE-1] = 0; prom_meminit(); diff --git a/arch/mips/sibyte/cfe/console.c b/arch/mips/sibyte/common/cfe_console.c index 81e3d54376e..1ad2da103fe 100644 --- a/arch/mips/sibyte/cfe/console.c +++ b/arch/mips/sibyte/common/cfe_console.c @@ -51,12 +51,13 @@ static int cfe_console_setup(struct console *cons, char *str) setleds("u0cn"); } else if (!strcmp(consdev, "uart1")) { setleds("u1cn"); + } else #endif #ifdef CONFIG_VGA_CONSOLE - } else if (!strcmp(consdev, "pcconsole0")) { - setleds("pccn"); -#endif + if (!strcmp(consdev, "pcconsole0")) { + setleds("pccn"); } else +#endif return -ENODEV; } return 0; diff --git a/arch/mips/sibyte/common/sb_tbprof.c b/arch/mips/sibyte/common/sb_tbprof.c index 637a194e5cd..059e28c8fd9 100644 --- a/arch/mips/sibyte/common/sb_tbprof.c +++ b/arch/mips/sibyte/common/sb_tbprof.c @@ -27,8 +27,7 @@ #include <linux/types.h> #include <linux/init.h> #include <linux/interrupt.h> -#include <linux/slab.h> -#include <linux/smp_lock.h> +#include <linux/sched.h> #include <linux/vmalloc.h> #include <linux/fs.h> #include <linux/errno.h> @@ -45,7 +44,7 @@ #include <asm/sibyte/sb1250_scd.h> #include <asm/sibyte/sb1250_int.h> #else -#error invalid SiByte UART configuation +#error invalid SiByte UART configuration #endif #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) @@ -55,7 +54,6 @@ #define K_INT_PERF_CNT K_BCM1480_INT_PERF_CNT #endif -#include <asm/system.h> #include <asm/uaccess.h> #define SBPROF_TB_MAJOR 240 @@ -155,7 +153,7 @@ static u64 tb_period; static void arm_tb(void) { - u64 scdperfcnt; + u64 scdperfcnt; u64 next = (1ULL << 40) - tb_period; u64 tb_options = M_SCD_TRACE_CFG_FREEZE_FULL; @@ -260,8 +258,8 @@ static irqreturn_t sbprof_pc_intr(int irq, void *dev_id) /* * Requires: Already called zclk_timer_init with a value that won't - * saturate 40 bits. No subsequent use of SCD performance counters - * or trace buffer. + * saturate 40 bits. No subsequent use of SCD performance counters + * or trace buffer. */ static int sbprof_zbprof_start(struct file *filp) @@ -291,8 +289,8 @@ static int sbprof_zbprof_start(struct file *filp) /* * We grab this interrupt to prevent others from trying to use - * it, even though we don't want to service the interrupts - * (they only feed into the trace-on-interrupt mechanism) + * it, even though we don't want to service the interrupts + * (they only feed into the trace-on-interrupt mechanism) */ if (request_irq(K_INT_PERF_CNT, sbprof_pc_intr, 0, DEVNAME " scd perfcnt", &sbp)) { free_irq(K_INT_TRACE_FREEZE, &sbp); @@ -301,7 +299,7 @@ static int sbprof_zbprof_start(struct file *filp) /* * I need the core to mask these, but the interrupt mapper to - * pass them through. I am exploiting my knowledge that + * pass them through. I am exploiting my knowledge that * cp0_status masks out IP[5]. krw */ #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) @@ -331,7 +329,7 @@ static int sbprof_zbprof_start(struct file *filp) __raw_writeq(0, IOADDR(A_ADDR_TRAP_CFG_3)); /* Initialize Trace Event 0-7 */ - /* when interrupt */ + /* when interrupt */ __raw_writeq(M_SCD_TREVT_INTERRUPT, IOADDR(A_SCD_TRACE_EVENT_0)); __raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_1)); __raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_2)); @@ -403,36 +401,30 @@ static int sbprof_zbprof_stop(void) static int sbprof_tb_open(struct inode *inode, struct file *filp) { int minor; - int err = 0; - lock_kernel(); minor = iminor(inode); - if (minor != 0) { - err = -ENODEV; - goto out; - } + if (minor != 0) + return -ENODEV; - if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED) { - err = -EBUSY; - goto out; - } + if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED) + return -EBUSY; memset(&sbp, 0, sizeof(struct sbprof_tb)); - sbp.sbprof_tbbuf = vmalloc(MAX_TBSAMPLE_BYTES); + sbp.sbprof_tbbuf = vzalloc(MAX_TBSAMPLE_BYTES); if (!sbp.sbprof_tbbuf) { - err = -ENOMEM; - goto out; + sbp.open = SB_CLOSED; + wmb(); + return -ENOMEM; } - memset(sbp.sbprof_tbbuf, 0, MAX_TBSAMPLE_BYTES); + init_waitqueue_head(&sbp.tb_sync); init_waitqueue_head(&sbp.tb_read); mutex_init(&sbp.lock); sbp.open = SB_OPEN; + wmb(); - out: - unlock_kernel(); - return err; + return 0; } static int sbprof_tb_release(struct inode *inode, struct file *filp) @@ -440,7 +432,7 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp) int minor; minor = iminor(inode); - if (minor != 0 || !sbp.open) + if (minor != 0 || sbp.open != SB_CLOSED) return -ENODEV; mutex_lock(&sbp.lock); @@ -449,7 +441,8 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp) sbprof_zbprof_stop(); vfree(sbp.sbprof_tbbuf); - sbp.open = 0; + sbp.open = SB_CLOSED; + wmb(); mutex_unlock(&sbp.lock); @@ -487,7 +480,7 @@ static ssize_t sbprof_tb_read(struct file *filp, char *buf, return err; } pr_debug(DEVNAME ": read from sample %d, %d bytes\n", - cur_sample, cur_count); + cur_sample, cur_count); size -= cur_count; sample_left -= cur_count; if (!sample_left) { @@ -548,9 +541,10 @@ static const struct file_operations sbprof_tb_fops = { .open = sbprof_tb_open, .release = sbprof_tb_release, .read = sbprof_tb_read, - .unlocked_ioctl = sbprof_tb_ioctl, + .unlocked_ioctl = sbprof_tb_ioctl, .compat_ioctl = sbprof_tb_ioctl, .mmap = NULL, + .llseek = default_llseek, }; static struct class *tb_class; @@ -583,7 +577,8 @@ static int __init sbprof_tb_init(void) } tb_dev = dev; - sbp.open = 0; + sbp.open = SB_CLOSED; + wmb(); tb_period = zbbus_mhz * 10000LL; pr_info(DEVNAME ": initialized - tb_period = %lld\n", (long long) tb_period); diff --git a/arch/mips/sibyte/sb1250/Makefile b/arch/mips/sibyte/sb1250/Makefile index 697793783a2..cdc4c56c3e2 100644 --- a/arch/mips/sibyte/sb1250/Makefile +++ b/arch/mips/sibyte/sb1250/Makefile @@ -1,7 +1,3 @@ obj-y := setup.o irq.o time.o obj-$(CONFIG_SMP) += smp.o -obj-$(CONFIG_SIBYTE_STANDALONE) += prom.o -obj-$(CONFIG_SIBYTE_BUS_WATCHER) += bus_watcher.o - -EXTRA_CFLAGS += -Werror diff --git a/arch/mips/sibyte/sb1250/irq.c b/arch/mips/sibyte/sb1250/irq.c index 409dec79886..6d8dba5cf34 100644 --- a/arch/mips/sibyte/sb1250/irq.c +++ b/arch/mips/sibyte/sb1250/irq.c @@ -22,12 +22,10 @@ #include <linux/spinlock.h> #include <linux/smp.h> #include <linux/mm.h> -#include <linux/slab.h> #include <linux/kernel_stat.h> #include <asm/errno.h> #include <asm/signal.h> -#include <asm/system.h> #include <asm/time.h> #include <asm/io.h> @@ -44,48 +42,27 @@ * for interrupt lines */ - -static void end_sb1250_irq(unsigned int irq); -static void enable_sb1250_irq(unsigned int irq); -static void disable_sb1250_irq(unsigned int irq); -static void ack_sb1250_irq(unsigned int irq); -#ifdef CONFIG_SMP -static int sb1250_set_affinity(unsigned int irq, const struct cpumask *mask); -#endif - #ifdef CONFIG_SIBYTE_HAS_LDT extern unsigned long ldt_eoi_space; #endif -static struct irq_chip sb1250_irq_type = { - .name = "SB1250-IMR", - .ack = ack_sb1250_irq, - .mask = disable_sb1250_irq, - .mask_ack = ack_sb1250_irq, - .unmask = enable_sb1250_irq, - .end = end_sb1250_irq, -#ifdef CONFIG_SMP - .set_affinity = sb1250_set_affinity -#endif -}; - /* Store the CPU id (not the logical number) */ int sb1250_irq_owner[SB1250_NR_IRQS]; -DEFINE_SPINLOCK(sb1250_imr_lock); +static DEFINE_RAW_SPINLOCK(sb1250_imr_lock); void sb1250_mask_irq(int cpu, int irq) { unsigned long flags; u64 cur_ints; - spin_lock_irqsave(&sb1250_imr_lock, flags); + raw_spin_lock_irqsave(&sb1250_imr_lock, flags); cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); cur_ints |= (((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); - spin_unlock_irqrestore(&sb1250_imr_lock, flags); + raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags); } void sb1250_unmask_irq(int cpu, int irq) @@ -93,34 +70,31 @@ void sb1250_unmask_irq(int cpu, int irq) unsigned long flags; u64 cur_ints; - spin_lock_irqsave(&sb1250_imr_lock, flags); + raw_spin_lock_irqsave(&sb1250_imr_lock, flags); cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); cur_ints &= ~(((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); - spin_unlock_irqrestore(&sb1250_imr_lock, flags); + raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags); } #ifdef CONFIG_SMP -static int sb1250_set_affinity(unsigned int irq, const struct cpumask *mask) +static int sb1250_set_affinity(struct irq_data *d, const struct cpumask *mask, + bool force) { int i = 0, old_cpu, cpu, int_on; + unsigned int irq = d->irq; u64 cur_ints; unsigned long flags; - i = cpumask_first(mask); - - if (cpumask_weight(mask) > 1) { - printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq); - return -1; - } + i = cpumask_first_and(mask, cpu_online_mask); /* Convert logical CPU to physical CPU */ cpu = cpu_logical_map(i); /* Protect against other affinity changers and IMR manipulation */ - spin_lock_irqsave(&sb1250_imr_lock, flags); + raw_spin_lock_irqsave(&sb1250_imr_lock, flags); /* Swizzle each CPU's IMR (but leave the IP selection alone) */ old_cpu = sb1250_irq_owner[irq]; @@ -142,27 +116,30 @@ static int sb1250_set_affinity(unsigned int irq, const struct cpumask *mask) ____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); } - spin_unlock_irqrestore(&sb1250_imr_lock, flags); + raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags); return 0; } #endif -/*****************************************************************************/ - -static void disable_sb1250_irq(unsigned int irq) +static void disable_sb1250_irq(struct irq_data *d) { + unsigned int irq = d->irq; + sb1250_mask_irq(sb1250_irq_owner[irq], irq); } -static void enable_sb1250_irq(unsigned int irq) +static void enable_sb1250_irq(struct irq_data *d) { + unsigned int irq = d->irq; + sb1250_unmask_irq(sb1250_irq_owner[irq], irq); } -static void ack_sb1250_irq(unsigned int irq) +static void ack_sb1250_irq(struct irq_data *d) { + unsigned int irq = d->irq; #ifdef CONFIG_SIBYTE_HAS_LDT u64 pending; @@ -205,21 +182,23 @@ static void ack_sb1250_irq(unsigned int irq) sb1250_mask_irq(sb1250_irq_owner[irq], irq); } - -static void end_sb1250_irq(unsigned int irq) -{ - if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) { - sb1250_unmask_irq(sb1250_irq_owner[irq], irq); - } -} - +static struct irq_chip sb1250_irq_type = { + .name = "SB1250-IMR", + .irq_mask_ack = ack_sb1250_irq, + .irq_unmask = enable_sb1250_irq, + .irq_mask = disable_sb1250_irq, +#ifdef CONFIG_SMP + .irq_set_affinity = sb1250_set_affinity +#endif +}; void __init init_sb1250_irqs(void) { int i; for (i = 0; i < SB1250_NR_IRQS; i++) { - set_irq_chip_and_handler(i, &sb1250_irq_type, handle_level_irq); + irq_set_chip_and_handler(i, &sb1250_irq_type, + handle_level_irq); sb1250_irq_owner[i] = 0; } } @@ -242,7 +221,7 @@ void __init init_sb1250_irqs(void) * On the second cpu, everything is set to IP5, which is * ignored, EXCEPT the mailbox interrupt. That one is * set to IP[2] so it is handled. This is needed so we - * can do cross-cpu function calls, as requred by SMP + * can do cross-cpu function calls, as required by SMP */ #define IMR_IP2_VAL K_INT_MAP_I0 @@ -285,7 +264,7 @@ void __init arch_init_irq(void) IOADDR(A_IMR_REGISTER(1, R_IMR_INTERRUPT_MAP_BASE) + (K_INT_MBOX_0 << 3))); - /* Clear the mailboxes. The firmware may leave them dirty */ + /* Clear the mailboxes. The firmware may leave them dirty */ __raw_writeq(0xffffffffffffffffULL, IOADDR(A_IMR_REGISTER(0, R_IMR_MAILBOX_CLR_CPU))); __raw_writeq(0xffffffffffffffffULL, @@ -298,7 +277,7 @@ void __init arch_init_irq(void) /* * Note that the timer interrupts are also mapped, but this is - * done in sb1250_time_init(). Also, the profiling driver + * done in sb1250_time_init(). Also, the profiling driver * does its own management of IP7. */ @@ -315,7 +294,7 @@ static inline void dispatch_ip2(void) /* * Default...we've hit an IP[2] interrupt, which means we've got to - * check the 1250 interrupt registers to figure out what to do. Need + * check the 1250 interrupt registers to figure out what to do. Need * to detect which CPU we're on, now that smp_affinity is supported. */ mask = __raw_readq(IOADDR(A_IMR_REGISTER(cpu, @@ -344,7 +323,7 @@ asmlinkage void plat_irq_dispatch(void) if (pending & CAUSEF_IP7) /* CPU performance counter interrupt */ do_IRQ(MIPS_CPU_IRQ_BASE + 7); else if (pending & CAUSEF_IP4) - do_IRQ(K_INT_TIMER_0 + cpu); /* sb1250_timer_interrupt() */ + do_IRQ(K_INT_TIMER_0 + cpu); /* sb1250_timer_interrupt() */ #ifdef CONFIG_SMP else if (pending & CAUSEF_IP3) diff --git a/arch/mips/sibyte/sb1250/prom.c b/arch/mips/sibyte/sb1250/prom.c deleted file mode 100644 index 65b1af66b67..00000000000 --- a/arch/mips/sibyte/sb1250/prom.c +++ /dev/null @@ -1,96 +0,0 @@ -/* - * Copyright (C) 2000, 2001 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/mm.h> -#include <linux/blkdev.h> -#include <linux/bootmem.h> -#include <linux/smp.h> -#include <linux/initrd.h> -#include <linux/pm.h> - -#include <asm/bootinfo.h> -#include <asm/reboot.h> - -#define MAX_RAM_SIZE ((CONFIG_SIBYTE_STANDALONE_RAM_SIZE * 1024 * 1024) - 1) - -static __init void prom_meminit(void) -{ -#ifdef CONFIG_BLK_DEV_INITRD - unsigned long initrd_pstart; - unsigned long initrd_pend; - - initrd_pstart = __pa(initrd_start); - initrd_pend = __pa(initrd_end); - if (initrd_start && - ((initrd_pstart > MAX_RAM_SIZE) - || (initrd_pend > MAX_RAM_SIZE))) { - panic("initrd out of addressable memory"); - } - - add_memory_region(0, initrd_pstart, - BOOT_MEM_RAM); - add_memory_region(initrd_pstart, initrd_pend - initrd_pstart, - BOOT_MEM_RESERVED); - add_memory_region(initrd_pend, - (CONFIG_SIBYTE_STANDALONE_RAM_SIZE * 1024 * 1024) - initrd_pend, - BOOT_MEM_RAM); -#else - add_memory_region(0, CONFIG_SIBYTE_STANDALONE_RAM_SIZE * 1024 * 1024, - BOOT_MEM_RAM); -#endif -} - -void prom_cpu0_exit(void *unused) -{ - while (1) ; -} - -static void prom_linux_exit(void) -{ -#ifdef CONFIG_SMP - if (smp_processor_id()) { - smp_call_function(prom_cpu0_exit, NULL, 1); - } -#endif - while(1); -} - -/* - * prom_init is called just after the cpu type is determined, from setup_arch() - */ -void __init prom_init(void) -{ - _machine_restart = (void (*)(char *))prom_linux_exit; - _machine_halt = prom_linux_exit; - pm_power_off = prom_linux_exit; - - strcpy(arcs_cmdline, "root=/dev/ram0 "); - - prom_meminit(); -} - -void __init prom_free_prom_memory(void) -{ - /* Not sure what I'm supposed to do here. Nothing, I think */ -} - -void prom_putchar(char c) -{ -} diff --git a/arch/mips/sibyte/sb1250/setup.c b/arch/mips/sibyte/sb1250/setup.c index 0444da1e23c..3c02b2a77ae 100644 --- a/arch/mips/sibyte/sb1250/setup.c +++ b/arch/mips/sibyte/sb1250/setup.c @@ -22,6 +22,7 @@ #include <linux/string.h> #include <asm/bootinfo.h> +#include <asm/cpu.h> #include <asm/mipsregs.h> #include <asm/io.h> #include <asm/sibyte/sb1250.h> @@ -87,6 +88,21 @@ static int __init setup_bcm1250(void) return ret; } +int sb1250_m3_workaround_needed(void) +{ + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1250: + case K_SYS_SOC_TYPE_BCM1250_ALT: + case K_SYS_SOC_TYPE_BCM1250_ALT2: + case K_SYS_SOC_TYPE_BCM1125: + case K_SYS_SOC_TYPE_BCM1125H: + return soc_pass < K_SYS_REVISION_BCM1250_C0; + + default: + return 0; + } +} + static int __init setup_bcm112x(void) { int ret = 0; @@ -167,7 +183,7 @@ void __init sb1250_setup(void) int plldiv; int bad_config = 0; - sb1_pass = read_c0_prid() & 0xff; + sb1_pass = read_c0_prid() & PRID_REV_MASK; sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION)); soc_type = SYS_SOC_TYPE(sys_rev); soc_pass = G_SYS_REVISION(sys_rev); @@ -188,8 +204,8 @@ void __init sb1250_setup(void) case K_SYS_REVISION_BCM1250_PASS1: #ifndef CONFIG_SB1_PASS_1_WORKAROUNDS printk("@@@@ This is a BCM1250 A0-A2 (Pass 1) board, " - "and the kernel doesn't have the proper " - "workarounds compiled in. @@@@\n"); + "and the kernel doesn't have the proper " + "workarounds compiled in. @@@@\n"); bad_config = 1; #endif break; @@ -198,28 +214,28 @@ void __init sb1250_setup(void) #if !defined(CONFIG_SB1_PASS_2_WORKAROUNDS) || \ !defined(CONFIG_SB1_PASS_2_1_WORKAROUNDS) printk("@@@@ This is a BCM1250 A3-A10 board, and the " - "kernel doesn't have the proper workarounds " - "compiled in. @@@@\n"); + "kernel doesn't have the proper workarounds " + "compiled in. @@@@\n"); bad_config = 1; #endif #ifdef CONFIG_CPU_HAS_PREFETCH printk("@@@@ Prefetches may be enabled in this kernel, " - "but are buggy on this board. @@@@\n"); + "but are buggy on this board. @@@@\n"); bad_config = 1; #endif break; case K_SYS_REVISION_BCM1250_PASS2_2: #ifndef CONFIG_SB1_PASS_2_WORKAROUNDS printk("@@@@ This is a BCM1250 B1/B2. board, and the " - "kernel doesn't have the proper workarounds " - "compiled in. @@@@\n"); + "kernel doesn't have the proper workarounds " + "compiled in. @@@@\n"); bad_config = 1; #endif #if defined(CONFIG_SB1_PASS_2_1_WORKAROUNDS) || \ !defined(CONFIG_CPU_HAS_PREFETCH) printk("@@@@ This is a BCM1250 B1/B2, but the kernel is " - "conservatively configured for an 'A' stepping. " - "@@@@\n"); + "conservatively configured for an 'A' stepping. " + "@@@@\n"); #endif break; default: diff --git a/arch/mips/sibyte/sb1250/smp.c b/arch/mips/sibyte/sb1250/smp.c index cad14003b84..c0c4b3f88a0 100644 --- a/arch/mips/sibyte/sb1250/smp.c +++ b/arch/mips/sibyte/sb1250/smp.c @@ -21,6 +21,7 @@ #include <linux/interrupt.h> #include <linux/smp.h> #include <linux/kernel_stat.h> +#include <linux/sched.h> #include <asm/mmu_context.h> #include <asm/io.h> @@ -47,7 +48,7 @@ static void *mailbox_regs[] = { /* * SMP init and finish on secondary CPUs */ -void __cpuinit sb1250_smp_init(void) +void sb1250_smp_init(void) { unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 | STATUSF_IP1 | STATUSF_IP0; @@ -70,18 +71,19 @@ static void sb1250_send_ipi_single(int cpu, unsigned int action) __raw_writeq((((u64)action) << 48), mailbox_set_regs[cpu]); } -static inline void sb1250_send_ipi_mask(cpumask_t mask, unsigned int action) +static inline void sb1250_send_ipi_mask(const struct cpumask *mask, + unsigned int action) { unsigned int i; - for_each_cpu_mask(i, mask) + for_each_cpu(i, mask) sb1250_send_ipi_single(i, action); } /* * Code to run on secondary just after probing the CPU */ -static void __cpuinit sb1250_init_secondary(void) +static void sb1250_init_secondary(void) { extern void sb1250_smp_init(void); @@ -92,7 +94,7 @@ static void __cpuinit sb1250_init_secondary(void) * Do any tidying up before marking online and running the idle * loop */ -static void __cpuinit sb1250_smp_finish(void) +static void sb1250_smp_finish(void) { extern void sb1250_clockevent_init(void); @@ -101,17 +103,10 @@ static void __cpuinit sb1250_smp_finish(void) } /* - * Final cleanup after all secondaries booted - */ -static void sb1250_cpus_done(void) -{ -} - -/* * Setup the PC, SP, and GP of a secondary processor and start it * running! */ -static void __cpuinit sb1250_boot_secondary(int cpu, struct task_struct *idle) +static void sb1250_boot_secondary(int cpu, struct task_struct *idle) { int retval; @@ -124,7 +119,7 @@ static void __cpuinit sb1250_boot_secondary(int cpu, struct task_struct *idle) /* * Use CFE to find out how many CPUs are available, setting up - * cpu_possible_map and the logical/physical mappings. + * cpu_possible_mask and the logical/physical mappings. * XXXKW will the boot CPU ever not be physical 0? * * Common setup before any secondaries are started @@ -133,14 +128,13 @@ static void __init sb1250_smp_setup(void) { int i, num; - cpus_clear(cpu_possible_map); - cpu_set(0, cpu_possible_map); + init_cpu_possible(cpumask_of(0)); __cpu_number_map[0] = 0; __cpu_logical_map[0] = 0; for (i = 1, num = 0; i < NR_CPUS; i++) { if (cfe_cpu_stop(i) == 0) { - cpu_set(i, cpu_possible_map); + set_cpu_possible(i, true); __cpu_number_map[i] = ++num; __cpu_logical_map[num] = i; } @@ -157,7 +151,6 @@ struct plat_smp_ops sb_smp_ops = { .send_ipi_mask = sb1250_send_ipi_mask, .init_secondary = sb1250_init_secondary, .smp_finish = sb1250_smp_finish, - .cpus_done = sb1250_cpus_done, .boot_secondary = sb1250_boot_secondary, .smp_setup = sb1250_smp_setup, .prepare_cpus = sb1250_prepare_cpus, @@ -169,17 +162,15 @@ void sb1250_mailbox_interrupt(void) int irq = K_INT_MBOX_0; unsigned int action; - kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq)); + kstat_incr_irq_this_cpu(irq); /* Load the mailbox register to figure out what we're supposed to do */ action = (____raw_readq(mailbox_regs[cpu]) >> 48) & 0xffff; /* Clear the mailbox to clear the interrupt */ ____raw_writeq(((u64)action) << 48, mailbox_clear_regs[cpu]); - /* - * Nothing to do for SMP_RESCHEDULE_YOURSELF; returning from the - * interrupt will do the reschedule for us - */ + if (action & SMP_RESCHEDULE_YOURSELF) + scheduler_ipi(); if (action & SMP_CALL_FUNCTION) smp_call_function_interrupt(); diff --git a/arch/mips/sibyte/swarm/platform.c b/arch/mips/sibyte/swarm/platform.c index 54847fe1e56..9480c14ec66 100644 --- a/arch/mips/sibyte/swarm/platform.c +++ b/arch/mips/sibyte/swarm/platform.c @@ -13,7 +13,7 @@ #define DRV_NAME "pata-swarm" -#define SWARM_IDE_SHIFT 5 +#define SWARM_IDE_SHIFT 5 #define SWARM_IDE_BASE 0x1f0 #define SWARM_IDE_CTRL 0x3f6 @@ -83,3 +83,57 @@ static int __init swarm_pata_init(void) device_initcall(swarm_pata_init); #endif /* defined(CONFIG_SIBYTE_SWARM) || defined(CONFIG_SIBYTE_LITTLESUR) */ + +#define sb1250_dev_struct(num) \ + static struct resource sb1250_res##num = { \ + .name = "SB1250 MAC " __stringify(num), \ + .flags = IORESOURCE_MEM, \ + .start = A_MAC_CHANNEL_BASE(num), \ + .end = A_MAC_CHANNEL_BASE(num + 1) -1, \ + };\ + static struct platform_device sb1250_dev##num = { \ + .name = "sb1250-mac", \ + .id = num, \ + .resource = &sb1250_res##num, \ + .num_resources = 1, \ + } + +sb1250_dev_struct(0); +sb1250_dev_struct(1); +sb1250_dev_struct(2); +sb1250_dev_struct(3); + +static struct platform_device *sb1250_devs[] __initdata = { + &sb1250_dev0, + &sb1250_dev1, + &sb1250_dev2, + &sb1250_dev3, +}; + +static int __init sb1250_device_init(void) +{ + int ret; + + /* Set the number of available units based on the SOC type. */ + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1250: + case K_SYS_SOC_TYPE_BCM1250_ALT: + ret = platform_add_devices(sb1250_devs, 3); + break; + case K_SYS_SOC_TYPE_BCM1120: + case K_SYS_SOC_TYPE_BCM1125: + case K_SYS_SOC_TYPE_BCM1125H: + case K_SYS_SOC_TYPE_BCM1250_ALT2: /* Hybrid */ + ret = platform_add_devices(sb1250_devs, 2); + break; + case K_SYS_SOC_TYPE_BCM1x55: + case K_SYS_SOC_TYPE_BCM1x80: + ret = platform_add_devices(sb1250_devs, 4); + break; + default: + ret = -ENODEV; + break; + } + return ret; +} +device_initcall(sb1250_device_init); diff --git a/arch/mips/sibyte/swarm/rtc_xicor1241.c b/arch/mips/sibyte/swarm/rtc_xicor1241.c index 4438b2195c4..178a824b28d 100644 --- a/arch/mips/sibyte/swarm/rtc_xicor1241.c +++ b/arch/mips/sibyte/swarm/rtc_xicor1241.c @@ -4,8 +4,8 @@ * Copyright (C) 2002 MontaVista Software Inc. * Author: jsun@mvista.com or jsun@junsun.net * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ @@ -28,15 +28,15 @@ * Register bits */ -#define X1241REG_SR_BAT 0x80 /* currently on battery power */ +#define X1241REG_SR_BAT 0x80 /* currently on battery power */ #define X1241REG_SR_RWEL 0x04 /* r/w latch is enabled, can write RTC */ #define X1241REG_SR_WEL 0x02 /* r/w latch is unlocked, can enable r/w now */ #define X1241REG_SR_RTCF 0x01 /* clock failed */ #define X1241REG_BL_BP2 0x80 /* block protect 2 */ #define X1241REG_BL_BP1 0x40 /* block protect 1 */ #define X1241REG_BL_BP0 0x20 /* block protect 0 */ -#define X1241REG_BL_WD1 0x10 -#define X1241REG_BL_WD0 0x08 +#define X1241REG_BL_WD1 0x10 +#define X1241REG_BL_WD0 0x08 #define X1241REG_HR_MIL 0x80 /* military time format */ /* @@ -61,50 +61,50 @@ static int xicor_read(uint8_t addr) { - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; __raw_writeq((addr >> 8) & 0x7, SMB_CSR(R_SMB_CMD)); __raw_writeq(addr & 0xff, SMB_CSR(R_SMB_DATA)); __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR2BYTE, SMB_CSR(R_SMB_START)); - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_RD1BYTE, SMB_CSR(R_SMB_START)); - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; - if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { - /* Clear error bit by writing a 1 */ - __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); - return -1; - } + if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { + /* Clear error bit by writing a 1 */ + __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); + return -1; + } return (__raw_readq(SMB_CSR(R_SMB_DATA)) & 0xff); } static int xicor_write(uint8_t addr, int b) { - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; __raw_writeq(addr, SMB_CSR(R_SMB_CMD)); __raw_writeq((addr & 0xff) | ((b & 0xff) << 8), SMB_CSR(R_SMB_DATA)); __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR3BYTE, SMB_CSR(R_SMB_START)); - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; - if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { - /* Clear error bit by writing a 1 */ - __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); - return -1; - } else { + if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { + /* Clear error bit by writing a 1 */ + __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); + return -1; + } else { return 0; } } diff --git a/arch/mips/sibyte/swarm/setup.c b/arch/mips/sibyte/swarm/setup.c index 080c966263b..3462c831d0e 100644 --- a/arch/mips/sibyte/swarm/setup.c +++ b/arch/mips/sibyte/swarm/setup.c @@ -82,24 +82,31 @@ int swarm_be_handler(struct pt_regs *regs, int is_fixup) enum swarm_rtc_type { RTC_NONE, RTC_XICOR, - RTC_M4LT81 + RTC_M41T81, }; enum swarm_rtc_type swarm_rtc_type; -unsigned long read_persistent_clock(void) +void read_persistent_clock(struct timespec *ts) { + unsigned long sec; + switch (swarm_rtc_type) { case RTC_XICOR: - return xicor_get_time(); + sec = xicor_get_time(); + break; - case RTC_M4LT81: - return m41t81_get_time(); + case RTC_M41T81: + sec = m41t81_get_time(); + break; case RTC_NONE: default: - return mktime(2000, 1, 1, 0, 0, 0); + sec = mktime(2000, 1, 1, 0, 0, 0); + break; } + ts->tv_sec = sec; + ts->tv_nsec = 0; } int rtc_mips_set_time(unsigned long sec) @@ -108,7 +115,7 @@ int rtc_mips_set_time(unsigned long sec) case RTC_XICOR: return xicor_set_time(sec); - case RTC_M4LT81: + case RTC_M41T81: return m41t81_set_time(sec); case RTC_NONE: @@ -127,40 +134,23 @@ void __init plat_mem_setup(void) #error invalid SiByte board configuration #endif - panic_timeout = 5; /* For debug. */ - board_be_handler = swarm_be_handler; if (xicor_probe()) swarm_rtc_type = RTC_XICOR; if (m41t81_probe()) - swarm_rtc_type = RTC_M4LT81; - - printk("This kernel optimized for " -#ifdef CONFIG_SIMULATION - "simulation" -#else - "board" -#endif - " runs " -#ifdef CONFIG_SIBYTE_CFE - "with" -#else - "without" -#endif - " CFE\n"); + swarm_rtc_type = RTC_M41T81; #ifdef CONFIG_VT screen_info = (struct screen_info) { - 0, 0, /* orig-x, orig-y */ - 0, /* unused */ - 52, /* orig_video_page */ - 3, /* orig_video_mode */ - 80, /* orig_video_cols */ - 4626, 3, 9, /* unused, ega_bx, unused */ - 25, /* orig_video_lines */ - 0x22, /* orig_video_isVGA */ - 16 /* orig_video_points */ + .orig_video_page = 52, + .orig_video_mode = 3, + .orig_video_cols = 80, + .flags = 12, + .orig_video_ega_bx = 3, + .orig_video_lines = 25, + .orig_video_isVGA = 0x22, + .orig_video_points = 16, }; /* XXXKW for CFE, get lines/cols from environment */ #endif diff --git a/arch/mips/sibyte/swarm/swarm-i2c.c b/arch/mips/sibyte/swarm/swarm-i2c.c index 4282ac9d01d..062505054d4 100644 --- a/arch/mips/sibyte/swarm/swarm-i2c.c +++ b/arch/mips/sibyte/swarm/swarm-i2c.c @@ -1,6 +1,4 @@ /* - * arch/mips/sibyte/swarm/swarm-i2c.c - * * Broadcom BCM91250A (SWARM), etc. I2C platform setup. * * Copyright (c) 2008 Maciej W. Rozycki |