diff options
Diffstat (limited to 'arch/mips/sibyte')
32 files changed, 926 insertions, 2479 deletions
diff --git a/arch/mips/sibyte/Kconfig b/arch/mips/sibyte/Kconfig index e6b003ec671..5fbd3605d24 100644 --- a/arch/mips/sibyte/Kconfig +++ b/arch/mips/sibyte/Kconfig @@ -1,6 +1,9 @@ config SIBYTE_SB1250 bool + select CEVT_SB1250 + select CSRC_SB1250 select HW_HAS_PCI + select IRQ_CPU select SIBYTE_ENABLE_LDT_IF_PCI select SIBYTE_HAS_ZBUS_PROFILING select SIBYTE_SB1xxx_SOC @@ -8,20 +11,29 @@ config SIBYTE_SB1250 config SIBYTE_BCM1120 bool + select CEVT_SB1250 + select CSRC_SB1250 + select IRQ_CPU select SIBYTE_BCM112X select SIBYTE_HAS_ZBUS_PROFILING select SIBYTE_SB1xxx_SOC config SIBYTE_BCM1125 bool + select CEVT_SB1250 + select CSRC_SB1250 select HW_HAS_PCI + select IRQ_CPU select SIBYTE_BCM112X select SIBYTE_HAS_ZBUS_PROFILING select SIBYTE_SB1xxx_SOC config SIBYTE_BCM1125H bool + select CEVT_SB1250 + select CSRC_SB1250 select HW_HAS_PCI + select IRQ_CPU select SIBYTE_BCM112X select SIBYTE_ENABLE_LDT_IF_PCI select SIBYTE_HAS_ZBUS_PROFILING @@ -29,31 +41,41 @@ config SIBYTE_BCM1125H config SIBYTE_BCM112X bool + select CEVT_SB1250 + select CSRC_SB1250 + select IRQ_CPU select SIBYTE_SB1xxx_SOC select SIBYTE_HAS_ZBUS_PROFILING config SIBYTE_BCM1x80 bool + select CEVT_BCM1480 + select CSRC_BCM1480 select HW_HAS_PCI + select IRQ_CPU select SIBYTE_HAS_ZBUS_PROFILING select SIBYTE_SB1xxx_SOC select SYS_SUPPORTS_SMP config SIBYTE_BCM1x55 bool + select CEVT_BCM1480 + select CSRC_BCM1480 select HW_HAS_PCI + select IRQ_CPU select SIBYTE_SB1xxx_SOC select SIBYTE_HAS_ZBUS_PROFILING select SYS_SUPPORTS_SMP config SIBYTE_SB1xxx_SOC bool - depends on EXPERIMENTAL select DMA_COHERENT - select SIBYTE_CFE + select IRQ_CPU select SWAP_IO_SPACE select SYS_SUPPORTS_32BIT_KERNEL select SYS_SUPPORTS_64BIT_KERNEL + select FW_CFE + select SYS_HAS_EARLY_PRINTK choice prompt "SiByte SOC Stepping" @@ -107,13 +129,6 @@ config SIBYTE_ENABLE_LDT_IF_PCI bool select SIBYTE_HAS_LDT if PCI -config SIMULATION - bool "Running under simulation" - depends on SIBYTE_SB1xxx_SOC - help - Build a kernel suitable for running under the GDB simulator. - Primarily adjusts the kernel's notion of time. - config SB1_CEX_ALWAYS_FATAL bool "All cache exceptions considered fatal (no recovery attempted)" depends on SIBYTE_SB1xxx_SOC @@ -122,36 +137,18 @@ config SB1_CERR_STALL bool "Stall (rather than panic) on fatal cache error" depends on SIBYTE_SB1xxx_SOC -config SIBYTE_CFE - bool "Booting from CFE" - depends on SIBYTE_SB1xxx_SOC - select SYS_HAS_EARLY_PRINTK - help - Make use of the CFE API for enumerating available memory, - controlling secondary CPUs, and possibly console output. - config SIBYTE_CFE_CONSOLE bool "Use firmware console" - depends on SIBYTE_CFE + depends on SIBYTE_SB1xxx_SOC help Use the CFE API's console write routines during boot. Other console options (VT console, sb1250 duart console, etc.) should not be configured. -config SIBYTE_STANDALONE - bool - depends on SIBYTE_SB1xxx_SOC && !SIBYTE_CFE - select SYS_HAS_EARLY_PRINTK - default y - -config SIBYTE_STANDALONE_RAM_SIZE - int "Memory size (in megabytes)" - depends on SIBYTE_STANDALONE - default "32" - config SIBYTE_BUS_WATCHER bool "Support for Bus Watcher statistics" - depends on SIBYTE_SB1xxx_SOC + depends on SIBYTE_SB1xxx_SOC && \ + (SIBYTE_BCM112X || SIBYTE_SB1250) help Handle and keep statistics on the bus error interrupts (COR_ECC, BAD_ECC, IO_BUS). @@ -166,10 +163,6 @@ config SIBYTE_BW_TRACE buffer activity. Raw buffer data is dumped to console, and must be processed off-line. -config SIBYTE_SB1250_PROF - bool "Support for SB1/SOC profiling - SB1/SCD perf counters" - depends on SIBYTE_SB1xxx_SOC - config SIBYTE_TBPROF tristate "Support for ZBbus profiling" depends on SIBYTE_HAS_ZBUS_PROFILING diff --git a/arch/mips/sibyte/Makefile b/arch/mips/sibyte/Makefile new file mode 100644 index 00000000000..c8ed2c807e6 --- /dev/null +++ b/arch/mips/sibyte/Makefile @@ -0,0 +1,27 @@ +# +# Sibyte SB1250 / BCM1480 family of SOCs +# +obj-$(CONFIG_SIBYTE_BCM112X) += sb1250/ +obj-$(CONFIG_SIBYTE_BCM112X) += common/ +obj-$(CONFIG_SIBYTE_SB1250) += sb1250/ +obj-$(CONFIG_SIBYTE_SB1250) += common/ +obj-$(CONFIG_SIBYTE_BCM1x55) += bcm1480/ +obj-$(CONFIG_SIBYTE_BCM1x55) += common/ +obj-$(CONFIG_SIBYTE_BCM1x80) += bcm1480/ +obj-$(CONFIG_SIBYTE_BCM1x80) += common/ + +# +# Sibyte BCM91120x (Carmel) board +# Sibyte BCM91120C (CRhine) board +# Sibyte BCM91125C (CRhone) board +# Sibyte BCM91125E (Rhone) board +# Sibyte SWARM board +# Sibyte BCM91x80 (BigSur) board +# +obj-$(CONFIG_SIBYTE_CARMEL) += swarm/ +obj-$(CONFIG_SIBYTE_CRHINE) += swarm/ +obj-$(CONFIG_SIBYTE_CRHONE) += swarm/ +obj-$(CONFIG_SIBYTE_RHONE) += swarm/ +obj-$(CONFIG_SIBYTE_SENTOSA) += swarm/ +obj-$(CONFIG_SIBYTE_SWARM) += swarm/ +obj-$(CONFIG_SIBYTE_BIGSUR) += swarm/ diff --git a/arch/mips/sibyte/Platform b/arch/mips/sibyte/Platform new file mode 100644 index 00000000000..af117330ce1 --- /dev/null +++ b/arch/mips/sibyte/Platform @@ -0,0 +1,44 @@ +# +# These are all rather similar so we consider them a single platform +# +platform-$(CONFIG_SIBYTE_BCM112X) += sibyte/ +platform-$(CONFIG_SIBYTE_SB1250) += sibyte/ +platform-$(CONFIG_SIBYTE_BCM1x55) += sibyte/ +platform-$(CONFIG_SIBYTE_BCM1x80) += sibyte/ + +# +# Sibyte SB1250 / BCM1480 family of SOCs +# +cflags-$(CONFIG_SIBYTE_BCM112X) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL + +cflags-$(CONFIG_SIBYTE_SB1250) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL + +cflags-$(CONFIG_SIBYTE_BCM1x55) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL + +cflags-$(CONFIG_SIBYTE_BCM1x80) += \ + -I$(srctree)/arch/mips/include/asm/mach-sibyte \ + -DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL + +# +# Sibyte BCM91120x (Carmel) board +# Sibyte BCM91120C (CRhine) board +# Sibyte BCM91125C (CRhone) board +# Sibyte BCM91125E (Rhone) board +# Sibyte BCM91250A (SWARM) board +# Sibyte BCM91250C2 (LittleSur) board +# Sibyte BCM91x80 (BigSur) board +# +load-$(CONFIG_SIBYTE_CARMEL) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_CRHINE) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_CRHONE) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_RHONE) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_SENTOSA) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_SWARM) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_BIGSUR) := 0xffffffff80100000 +load-$(CONFIG_SIBYTE_LITTLESUR) := 0xffffffff80100000 diff --git a/arch/mips/sibyte/bcm1480/irq.c b/arch/mips/sibyte/bcm1480/irq.c index ba0c4b776c8..373fbbc8425 100644 --- a/arch/mips/sibyte/bcm1480/irq.c +++ b/arch/mips/sibyte/bcm1480/irq.c @@ -19,15 +19,14 @@ #include <linux/init.h> #include <linux/linkage.h> #include <linux/interrupt.h> +#include <linux/smp.h> #include <linux/spinlock.h> #include <linux/mm.h> -#include <linux/slab.h> #include <linux/kernel_stat.h> #include <asm/errno.h> #include <asm/irq_regs.h> #include <asm/signal.h> -#include <asm/system.h> #include <asm/io.h> #include <asm/sibyte/bcm1480_regs.h> @@ -44,66 +43,21 @@ * for interrupt lines */ - -static void end_bcm1480_irq(unsigned int irq); -static void enable_bcm1480_irq(unsigned int irq); -static void disable_bcm1480_irq(unsigned int irq); -static void ack_bcm1480_irq(unsigned int irq); -#ifdef CONFIG_SMP -static void bcm1480_set_affinity(unsigned int irq, cpumask_t mask); -#endif - #ifdef CONFIG_PCI extern unsigned long ht_eoi_space; #endif -#ifdef CONFIG_KGDB -#include <asm/gdb-stub.h> -extern void breakpoint(void); -static int kgdb_irq; -#ifdef CONFIG_GDB_CONSOLE -extern void register_gdb_console(void); -#endif - -/* kgdb is on when configured. Pass "nokgdb" kernel arg to turn it off */ -static int kgdb_flag = 1; -static int __init nokgdb(char *str) -{ - kgdb_flag = 0; - return 1; -} -__setup("nokgdb", nokgdb); - -/* Default to UART1 */ -int kgdb_port = 1; -#ifdef CONFIG_SIBYTE_SB1250_DUART -extern char sb1250_duart_present[]; -#endif -#endif - -static struct irq_chip bcm1480_irq_type = { - .name = "BCM1480-IMR", - .ack = ack_bcm1480_irq, - .mask = disable_bcm1480_irq, - .mask_ack = ack_bcm1480_irq, - .unmask = enable_bcm1480_irq, - .end = end_bcm1480_irq, -#ifdef CONFIG_SMP - .set_affinity = bcm1480_set_affinity -#endif -}; - /* Store the CPU id (not the logical number) */ int bcm1480_irq_owner[BCM1480_NR_IRQS]; -DEFINE_SPINLOCK(bcm1480_imr_lock); +static DEFINE_RAW_SPINLOCK(bcm1480_imr_lock); void bcm1480_mask_irq(int cpu, int irq) { - unsigned long flags; - u64 cur_ints,hl_spacing; + unsigned long flags, hl_spacing; + u64 cur_ints; - spin_lock_irqsave(&bcm1480_imr_lock, flags); + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); hl_spacing = 0; if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) { hl_spacing = BCM1480_IMR_HL_SPACING; @@ -112,15 +66,15 @@ void bcm1480_mask_irq(int cpu, int irq) cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); cur_ints |= (((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); - spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); } void bcm1480_unmask_irq(int cpu, int irq) { - unsigned long flags; - u64 cur_ints,hl_spacing; + unsigned long flags, hl_spacing; + u64 cur_ints; - spin_lock_irqsave(&bcm1480_imr_lock, flags); + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); hl_spacing = 0; if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) { hl_spacing = BCM1480_IMR_HL_SPACING; @@ -129,30 +83,25 @@ void bcm1480_unmask_irq(int cpu, int irq) cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); cur_ints &= ~(((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing)); - spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); } #ifdef CONFIG_SMP -static void bcm1480_set_affinity(unsigned int irq, cpumask_t mask) +static int bcm1480_set_affinity(struct irq_data *d, const struct cpumask *mask, + bool force) { + unsigned int irq_dirty, irq = d->irq; int i = 0, old_cpu, cpu, int_on, k; u64 cur_ints; - struct irq_desc *desc = irq_desc + irq; unsigned long flags; - unsigned int irq_dirty; - if (cpus_weight(mask) != 1) { - printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq); - return; - } - i = first_cpu(mask); + i = cpumask_first_and(mask, cpu_online_mask); /* Convert logical CPU to physical CPU */ cpu = cpu_logical_map(i); /* Protect against other affinity changers and IMR manipulation */ - spin_lock_irqsave(&desc->lock, flags); - spin_lock(&bcm1480_imr_lock); + raw_spin_lock_irqsave(&bcm1480_imr_lock, flags); /* Swizzle each CPU's IMR (but leave the IP selection alone) */ old_cpu = bcm1480_irq_owner[irq]; @@ -177,29 +126,34 @@ static void bcm1480_set_affinity(unsigned int irq, cpumask_t mask) ____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING))); } } - spin_unlock(&bcm1480_imr_lock); - spin_unlock_irqrestore(&desc->lock, flags); + raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags); + + return 0; } #endif /*****************************************************************************/ -static void disable_bcm1480_irq(unsigned int irq) +static void disable_bcm1480_irq(struct irq_data *d) { + unsigned int irq = d->irq; + bcm1480_mask_irq(bcm1480_irq_owner[irq], irq); } -static void enable_bcm1480_irq(unsigned int irq) +static void enable_bcm1480_irq(struct irq_data *d) { + unsigned int irq = d->irq; + bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq); } -static void ack_bcm1480_irq(unsigned int irq) +static void ack_bcm1480_irq(struct irq_data *d) { + unsigned int irq_dirty, irq = d->irq; u64 pending; - unsigned int irq_dirty; int k; /* @@ -246,61 +200,27 @@ static void ack_bcm1480_irq(unsigned int irq) bcm1480_mask_irq(bcm1480_irq_owner[irq], irq); } - -static void end_bcm1480_irq(unsigned int irq) -{ - if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) { - bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq); - } -} - +static struct irq_chip bcm1480_irq_type = { + .name = "BCM1480-IMR", + .irq_mask_ack = ack_bcm1480_irq, + .irq_mask = disable_bcm1480_irq, + .irq_unmask = enable_bcm1480_irq, +#ifdef CONFIG_SMP + .irq_set_affinity = bcm1480_set_affinity +#endif +}; void __init init_bcm1480_irqs(void) { int i; for (i = 0; i < BCM1480_NR_IRQS; i++) { - set_irq_chip(i, &bcm1480_irq_type); + irq_set_chip_and_handler(i, &bcm1480_irq_type, + handle_level_irq); bcm1480_irq_owner[i] = 0; } } - -static irqreturn_t bcm1480_dummy_handler(int irq, void *dev_id) -{ - return IRQ_NONE; -} - -static struct irqaction bcm1480_dummy_action = { - .handler = bcm1480_dummy_handler, - .flags = 0, - .mask = CPU_MASK_NONE, - .name = "bcm1480-private", - .next = NULL, - .dev_id = 0 -}; - -int bcm1480_steal_irq(int irq) -{ - struct irq_desc *desc = irq_desc + irq; - unsigned long flags; - int retval = 0; - - if (irq >= BCM1480_NR_IRQS) - return -EINVAL; - - spin_lock_irqsave(&desc->lock,flags); - /* Don't allow sharing at all for these */ - if (desc->action != NULL) - retval = -EBUSY; - else { - desc->action = &bcm1480_dummy_action; - desc->depth = 0; - } - spin_unlock_irqrestore(&desc->lock,flags); - return 0; -} - /* * init_IRQ is called early in the boot sequence from init/main.c. It * is responsible for setting up the interrupt mapper and installing the @@ -318,7 +238,7 @@ int bcm1480_steal_irq(int irq) * On the second cpu, everything is set to IP5, which is * ignored, EXCEPT the mailbox interrupt. That one is * set to IP[2] so it is handled. This is needed so we - * can do cross-cpu function calls, as requred by SMP + * can do cross-cpu function calls, as required by SMP */ #define IMR_IP2_VAL K_BCM1480_INT_MAP_I0 @@ -329,7 +249,6 @@ int bcm1480_steal_irq(int irq) void __init arch_init_irq(void) { - unsigned int i, cpu; u64 tmp; unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 | @@ -364,10 +283,10 @@ void __init arch_init_irq(void) for (cpu = 0; cpu < 4; cpu++) { __raw_writeq(IMR_IP3_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (K_BCM1480_INT_MBOX_0_0 << 3))); - } + } - /* Clear the mailboxes. The firmware may leave them dirty */ + /* Clear the mailboxes. The firmware may leave them dirty */ for (cpu = 0; cpu < 4; cpu++) { __raw_writeq(0xffffffffffffffffULL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_0_CLR_CPU))); @@ -386,124 +305,57 @@ void __init arch_init_irq(void) __raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_L))); } - bcm1480_steal_irq(K_BCM1480_INT_MBOX_0_0); - /* * Note that the timer interrupts are also mapped, but this is - * done in bcm1480_time_init(). Also, the profiling driver + * done in bcm1480_time_init(). Also, the profiling driver * does its own management of IP7. */ -#ifdef CONFIG_KGDB - imask |= STATUSF_IP6; -#endif /* Enable necessary IPs, disable the rest */ change_c0_status(ST0_IM, imask); - -#ifdef CONFIG_KGDB - if (kgdb_flag) { - kgdb_irq = K_BCM1480_INT_UART_0 + kgdb_port; - -#ifdef CONFIG_SIBYTE_SB1250_DUART - sb1250_duart_present[kgdb_port] = 0; -#endif - /* Setup uart 1 settings, mapper */ - /* QQQ FIXME */ - __raw_writeq(M_DUART_IMR_BRK, IO_SPACE_BASE + A_DUART_IMRREG(kgdb_port)); - - bcm1480_steal_irq(kgdb_irq); - __raw_writeq(IMR_IP6_VAL, - IO_SPACE_BASE + A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + - (kgdb_irq<<3)); - bcm1480_unmask_irq(0, kgdb_irq); - -#ifdef CONFIG_GDB_CONSOLE - register_gdb_console(); -#endif - printk("Waiting for GDB on UART port %d\n", kgdb_port); - set_debug_traps(); - breakpoint(); - } -#endif } -#ifdef CONFIG_KGDB - -#include <linux/delay.h> - -#define duart_out(reg, val) csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port,reg))) -#define duart_in(reg) csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port,reg))) +extern void bcm1480_mailbox_interrupt(void); -static void bcm1480_kgdb_interrupt(void) +static inline void dispatch_ip2(void) { + unsigned long long mask_h, mask_l; + unsigned int cpu = smp_processor_id(); + unsigned long base; + /* - * Clear break-change status (allow some time for the remote - * host to stop the break, since we would see another - * interrupt on the end-of-break too) + * Default...we've hit an IP[2] interrupt, which means we've got to + * check the 1480 interrupt registers to figure out what to do. Need + * to detect which CPU we're on, now that smp_affinity is supported. */ - kstat.irqs[smp_processor_id()][kgdb_irq]++; - mdelay(500); - duart_out(R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT | - M_DUART_RX_EN | M_DUART_TX_EN); - set_async_breakpoint(&get_irq_regs()->cp0_epc); + base = A_BCM1480_IMR_MAPPER(cpu); + mask_h = __raw_readq( + IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_H)); + mask_l = __raw_readq( + IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_L)); + + if (mask_h) { + if (mask_h ^ 1) + do_IRQ(fls64(mask_h) - 1); + else if (mask_l) + do_IRQ(63 + fls64(mask_l)); + } } -#endif /* CONFIG_KGDB */ - -extern void bcm1480_timer_interrupt(void); -extern void bcm1480_mailbox_interrupt(void); - asmlinkage void plat_irq_dispatch(void) { + unsigned int cpu = smp_processor_id(); unsigned int pending; -#ifdef CONFIG_SIBYTE_BCM1480_PROF - /* Set compare to count to silence count/compare timer interrupts */ - write_c0_compare(read_c0_count()); -#endif - pending = read_c0_cause() & read_c0_status(); -#ifdef CONFIG_SIBYTE_BCM1480_PROF - if (pending & CAUSEF_IP7) /* Cpu performance counter interrupt */ - sbprof_cpu_intr(); - else -#endif - if (pending & CAUSEF_IP4) - bcm1480_timer_interrupt(); - + do_IRQ(K_BCM1480_INT_TIMER_0 + cpu); #ifdef CONFIG_SMP else if (pending & CAUSEF_IP3) bcm1480_mailbox_interrupt(); #endif -#ifdef CONFIG_KGDB - else if (pending & CAUSEF_IP6) - bcm1480_kgdb_interrupt(); /* KGDB (uart 1) */ -#endif - - else if (pending & CAUSEF_IP2) { - unsigned long long mask_h, mask_l; - unsigned long base; - - /* - * Default...we've hit an IP[2] interrupt, which means we've - * got to check the 1480 interrupt registers to figure out what - * to do. Need to detect which CPU we're on, now that - * smp_affinity is supported. - */ - base = A_BCM1480_IMR_MAPPER(smp_processor_id()); - mask_h = __raw_readq( - IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_H)); - mask_l = __raw_readq( - IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_L)); - - if (mask_h) { - if (mask_h ^ 1) - do_IRQ(fls64(mask_h) - 1); - else - do_IRQ(63 + fls64(mask_l)); - } - } + else if (pending & CAUSEF_IP2) + dispatch_ip2(); } diff --git a/arch/mips/sibyte/bcm1480/setup.c b/arch/mips/sibyte/bcm1480/setup.c index bdaac34ae70..8e2e04f7787 100644 --- a/arch/mips/sibyte/bcm1480/setup.c +++ b/arch/mips/sibyte/bcm1480/setup.c @@ -15,11 +15,14 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ +#include <linux/init.h> #include <linux/kernel.h> +#include <linux/module.h> #include <linux/reboot.h> #include <linux/string.h> #include <asm/bootinfo.h> +#include <asm/cpu.h> #include <asm/mipsregs.h> #include <asm/io.h> #include <asm/sibyte/sb1250.h> @@ -31,24 +34,59 @@ unsigned int sb1_pass; unsigned int soc_pass; unsigned int soc_type; +EXPORT_SYMBOL(soc_type); unsigned int periph_rev; unsigned int zbbus_mhz; +EXPORT_SYMBOL(zbbus_mhz); static unsigned int part_type; static char *soc_str; static char *pass_str; -static inline int setup_bcm1x80_bcm1x55(void); +static int __init setup_bcm1x80_bcm1x55(void) +{ + int ret = 0; + + switch (soc_pass) { + case K_SYS_REVISION_BCM1480_S0: + periph_rev = 1; + pass_str = "S0 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_A1: + periph_rev = 1; + pass_str = "A1 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_A2: + periph_rev = 1; + pass_str = "A2 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_A3: + periph_rev = 1; + pass_str = "A3 (pass1)"; + break; + case K_SYS_REVISION_BCM1480_B0: + periph_rev = 1; + pass_str = "B0 (pass2)"; + break; + default: + printk("Unknown %s rev %x\n", soc_str, soc_pass); + periph_rev = 1; + pass_str = "Unknown Revision"; + break; + } + + return ret; +} /* Setup code likely to be common to all SiByte platforms */ -static inline int sys_rev_decode(void) +static int __init sys_rev_decode(void) { int ret = 0; switch (soc_type) { - case K_SYS_SOC_TYPE_BCM1x80: + case K_SYS_SOC_TYPE_BCM1x80: if (part_type == K_SYS_PART_BCM1480) soc_str = "BCM1480"; else if (part_type == K_SYS_PART_BCM1280) @@ -58,7 +96,7 @@ static inline int sys_rev_decode(void) ret = setup_bcm1x80_bcm1x55(); break; - case K_SYS_SOC_TYPE_BCM1x55: + case K_SYS_SOC_TYPE_BCM1x55: if (part_type == K_SYS_PART_BCM1455) soc_str = "BCM1455"; else if (part_type == K_SYS_PART_BCM1255) @@ -68,54 +106,21 @@ static inline int sys_rev_decode(void) ret = setup_bcm1x80_bcm1x55(); break; - default: + default: printk("Unknown part type %x\n", part_type); ret = 1; break; } - return ret; -} -static inline int setup_bcm1x80_bcm1x55(void) -{ - int ret = 0; - - switch (soc_pass) { - case K_SYS_REVISION_BCM1480_S0: - periph_rev = 1; - pass_str = "S0 (pass1)"; - break; - case K_SYS_REVISION_BCM1480_A1: - periph_rev = 1; - pass_str = "A1 (pass1)"; - break; - case K_SYS_REVISION_BCM1480_A2: - periph_rev = 1; - pass_str = "A2 (pass1)"; - break; - case K_SYS_REVISION_BCM1480_A3: - periph_rev = 1; - pass_str = "A3 (pass1)"; - break; - case K_SYS_REVISION_BCM1480_B0: - periph_rev = 1; - pass_str = "B0 (pass2)"; - break; - default: - printk("Unknown %s rev %x\n", soc_str, soc_pass); - periph_rev = 1; - pass_str = "Unknown Revision"; - break; - } return ret; } -void bcm1480_setup(void) +void __init bcm1480_setup(void) { uint64_t sys_rev; int plldiv; - sb1_pass = read_c0_prid() & 0xff; + sb1_pass = read_c0_prid() & PRID_REV_MASK; sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION)); soc_type = SYS_SOC_TYPE(sys_rev); part_type = G_SYS_PART(sys_rev); diff --git a/arch/mips/sibyte/bcm1480/smp.c b/arch/mips/sibyte/bcm1480/smp.c index 6eac36d1b8c..af7d44edd9a 100644 --- a/arch/mips/sibyte/bcm1480/smp.c +++ b/arch/mips/sibyte/bcm1480/smp.c @@ -20,9 +20,11 @@ #include <linux/delay.h> #include <linux/smp.h> #include <linux/kernel_stat.h> +#include <linux/sched.h> #include <asm/mmu_context.h> #include <asm/io.h> +#include <asm/fw/cfe/cfe_api.h> #include <asm/sibyte/sb1250.h> #include <asm/sibyte/bcm1480_regs.h> #include <asm/sibyte/bcm1480_int.h> @@ -67,13 +69,6 @@ void bcm1480_smp_init(void) change_c0_status(ST0_IM, imask); } -void bcm1480_smp_finish(void) -{ - extern void bcm1480_time_init(void); - bcm1480_time_init(); - local_irq_enable(); -} - /* * These are routines for dealing with the sb1250 smp capabilities * independent of board/firmware @@ -83,27 +78,111 @@ void bcm1480_smp_finish(void) * Simple enough; everything is set up, so just poke the appropriate mailbox * register, and we should be set */ -void core_send_ipi(int cpu, unsigned int action) +static void bcm1480_send_ipi_single(int cpu, unsigned int action) { __raw_writeq((((u64)action)<< 48), mailbox_0_set_regs[cpu]); } +static void bcm1480_send_ipi_mask(const struct cpumask *mask, + unsigned int action) +{ + unsigned int i; + + for_each_cpu(i, mask) + bcm1480_send_ipi_single(i, action); +} + +/* + * Code to run on secondary just after probing the CPU + */ +static void bcm1480_init_secondary(void) +{ + extern void bcm1480_smp_init(void); + + bcm1480_smp_init(); +} + +/* + * Do any tidying up before marking online and running the idle + * loop + */ +static void bcm1480_smp_finish(void) +{ + extern void sb1480_clockevent_init(void); + + sb1480_clockevent_init(); + local_irq_enable(); +} + +/* + * Setup the PC, SP, and GP of a secondary processor and start it + * running! + */ +static void bcm1480_boot_secondary(int cpu, struct task_struct *idle) +{ + int retval; + + retval = cfe_cpu_start(cpu_logical_map(cpu), &smp_bootstrap, + __KSTK_TOS(idle), + (unsigned long)task_thread_info(idle), 0); + if (retval != 0) + printk("cfe_start_cpu(%i) returned %i\n" , cpu, retval); +} + +/* + * Use CFE to find out how many CPUs are available, setting up + * cpu_possible_mask and the logical/physical mappings. + * XXXKW will the boot CPU ever not be physical 0? + * + * Common setup before any secondaries are started + */ +static void __init bcm1480_smp_setup(void) +{ + int i, num; + + init_cpu_possible(cpumask_of(0)); + __cpu_number_map[0] = 0; + __cpu_logical_map[0] = 0; + + for (i = 1, num = 0; i < NR_CPUS; i++) { + if (cfe_cpu_stop(i) == 0) { + set_cpu_possible(i, true); + __cpu_number_map[i] = ++num; + __cpu_logical_map[num] = i; + } + } + printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num); +} + +static void __init bcm1480_prepare_cpus(unsigned int max_cpus) +{ +} + +struct plat_smp_ops bcm1480_smp_ops = { + .send_ipi_single = bcm1480_send_ipi_single, + .send_ipi_mask = bcm1480_send_ipi_mask, + .init_secondary = bcm1480_init_secondary, + .smp_finish = bcm1480_smp_finish, + .boot_secondary = bcm1480_boot_secondary, + .smp_setup = bcm1480_smp_setup, + .prepare_cpus = bcm1480_prepare_cpus, +}; + void bcm1480_mailbox_interrupt(void) { int cpu = smp_processor_id(); + int irq = K_BCM1480_INT_MBOX_0_0; unsigned int action; - kstat_this_cpu.irqs[K_BCM1480_INT_MBOX_0_0]++; + kstat_incr_irq_this_cpu(irq); /* Load the mailbox register to figure out what we're supposed to do */ action = (__raw_readq(mailbox_0_regs[cpu]) >> 48) & 0xffff; /* Clear the mailbox to clear the interrupt */ __raw_writeq(((u64)action)<<48, mailbox_0_clear_regs[cpu]); - /* - * Nothing to do for SMP_RESCHEDULE_YOURSELF; returning from the - * interrupt will do the reschedule for us - */ + if (action & SMP_RESCHEDULE_YOURSELF) + scheduler_ipi(); if (action & SMP_CALL_FUNCTION) smp_call_function_interrupt(); diff --git a/arch/mips/sibyte/bcm1480/time.c b/arch/mips/sibyte/bcm1480/time.c index 6f3f71bf424..1680a68952a 100644 --- a/arch/mips/sibyte/bcm1480/time.c +++ b/arch/mips/sibyte/bcm1480/time.c @@ -15,118 +15,13 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ +#include <linux/init.h> -/* - * These are routines to set up and handle interrupts from the - * bcm1480 general purpose timer 0. We're using the timer as a - * system clock, so we set it up to run at 100 Hz. On every - * interrupt, we update our idea of what the time of day is, - * then call do_timer() in the architecture-independent kernel - * code to do general bookkeeping (e.g. update jiffies, run - * bottom halves, etc.) - */ -#include <linux/interrupt.h> -#include <linux/sched.h> -#include <linux/spinlock.h> -#include <linux/kernel_stat.h> - -#include <asm/irq.h> -#include <asm/addrspace.h> -#include <asm/time.h> -#include <asm/io.h> - -#include <asm/sibyte/bcm1480_regs.h> -#include <asm/sibyte/sb1250_regs.h> -#include <asm/sibyte/bcm1480_int.h> -#include <asm/sibyte/bcm1480_scd.h> - -#include <asm/sibyte/sb1250.h> - - -#define IMR_IP2_VAL K_BCM1480_INT_MAP_I0 -#define IMR_IP3_VAL K_BCM1480_INT_MAP_I1 -#define IMR_IP4_VAL K_BCM1480_INT_MAP_I2 - -#ifdef CONFIG_SIMULATION -#define BCM1480_HPT_VALUE 50000 -#else -#define BCM1480_HPT_VALUE 1000000 -#endif - -extern int bcm1480_steal_irq(int irq); - -void bcm1480_time_init(void) -{ - int cpu = smp_processor_id(); - int irq = K_BCM1480_INT_TIMER_0+cpu; - - /* Only have 4 general purpose timers */ - if (cpu > 3) { - BUG(); - } - - bcm1480_mask_irq(cpu, irq); - - /* Map the timer interrupt to ip[4] of this cpu */ - __raw_writeq(IMR_IP4_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) - + (irq<<3))); - - /* the general purpose timer ticks at 1 Mhz independent of the rest of the system */ - /* Disable the timer and set up the count */ - __raw_writeq(0, IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG))); - __raw_writeq( - BCM1480_HPT_VALUE/HZ - , IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT))); - - /* Set the timer running */ - __raw_writeq(M_SCD_TIMER_ENABLE|M_SCD_TIMER_MODE_CONTINUOUS, - IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG))); - - bcm1480_unmask_irq(cpu, irq); - bcm1480_steal_irq(irq); - /* - * This interrupt is "special" in that it doesn't use the request_irq - * way to hook the irq line. The timer interrupt is initialized early - * enough to make this a major pain, and it's also firing enough to - * warrant a bit of special case code. bcm1480_timer_interrupt is - * called directly from irq_handler.S when IP[4] is set during an - * interrupt - */ -} - -void bcm1480_timer_interrupt(void) -{ - int cpu = smp_processor_id(); - int irq = K_BCM1480_INT_TIMER_0 + cpu; - - /* Reset the timer */ - __raw_writeq(M_SCD_TIMER_ENABLE|M_SCD_TIMER_MODE_CONTINUOUS, - IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG))); - - if (cpu == 0) { - /* - * CPU 0 handles the global timer interrupt job - */ - ll_timer_interrupt(irq); - } - else { - /* - * other CPUs should just do profiling and process accounting - */ - ll_local_timer_interrupt(irq); - } -} - -static cycle_t bcm1480_hpt_read(void) -{ - /* We assume this function is called xtime_lock held. */ - unsigned long count = - __raw_readq(IOADDR(A_SCD_TIMER_REGISTER(0, R_SCD_TIMER_CNT))); - return (jiffies + 1) * (BCM1480_HPT_VALUE / HZ) - count; -} +extern void sb1480_clockevent_init(void); +extern void sb1480_clocksource_init(void); -void __init bcm1480_hpt_setup(void) +void __init plat_time_init(void) { - clocksource_mips.read = bcm1480_hpt_read; - mips_hpt_frequency = BCM1480_HPT_VALUE; + sb1480_clocksource_init(); + sb1480_clockevent_init(); } diff --git a/arch/mips/sibyte/cfe/Makefile b/arch/mips/sibyte/cfe/Makefile deleted file mode 100644 index 059d84a1d8a..00000000000 --- a/arch/mips/sibyte/cfe/Makefile +++ /dev/null @@ -1,3 +0,0 @@ -lib-y = cfe_api.o setup.o -lib-$(CONFIG_SMP) += smp.o -lib-$(CONFIG_SIBYTE_CFE_CONSOLE) += console.o diff --git a/arch/mips/sibyte/cfe/cfe_api.c b/arch/mips/sibyte/cfe/cfe_api.c deleted file mode 100644 index c0213605e18..00000000000 --- a/arch/mips/sibyte/cfe/cfe_api.c +++ /dev/null @@ -1,502 +0,0 @@ -/* - * Copyright (C) 2000, 2001, 2002 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* ********************************************************************* - * - * Broadcom Common Firmware Environment (CFE) - * - * Device Function stubs File: cfe_api.c - * - * This module contains device function stubs (small routines to - * call the standard "iocb" interface entry point to CFE). - * There should be one routine here per iocb function call. - * - * Authors: Mitch Lichtenberg, Chris Demetriou - * - ********************************************************************* */ - -#include "cfe_api.h" -#include "cfe_api_int.h" - -/* Cast from a native pointer to a cfe_xptr_t and back. */ -#define XPTR_FROM_NATIVE(n) ((cfe_xptr_t) (intptr_t) (n)) -#define NATIVE_FROM_XPTR(x) ((void *) (intptr_t) (x)) - -#ifdef CFE_API_IMPL_NAMESPACE -#define cfe_iocb_dispatch(a) __cfe_iocb_dispatch(a) -#endif -int cfe_iocb_dispatch(cfe_xiocb_t * xiocb); - -#if defined(CFE_API_common) || defined(CFE_API_ALL) -/* - * Declare the dispatch function with args of "intptr_t". - * This makes sure whatever model we're compiling in - * puts the pointers in a single register. For example, - * combining -mlong64 and -mips1 or -mips2 would lead to - * trouble, since the handle and IOCB pointer will be - * passed in two registers each, and CFE expects one. - */ - -static int (*cfe_dispfunc) (intptr_t handle, intptr_t xiocb) = 0; -static cfe_xuint_t cfe_handle = 0; - -int cfe_init(cfe_xuint_t handle, cfe_xuint_t ept) -{ - cfe_dispfunc = NATIVE_FROM_XPTR(ept); - cfe_handle = handle; - return 0; -} - -int cfe_iocb_dispatch(cfe_xiocb_t * xiocb) -{ - if (!cfe_dispfunc) - return -1; - return (*cfe_dispfunc) ((intptr_t) cfe_handle, (intptr_t) xiocb); -} -#endif /* CFE_API_common || CFE_API_ALL */ - -#if defined(CFE_API_close) || defined(CFE_API_ALL) -int cfe_close(int handle) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_CLOSE; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = handle; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = 0; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; - -} -#endif /* CFE_API_close || CFE_API_ALL */ - -#if defined(CFE_API_cpu_start) || defined(CFE_API_ALL) -int cfe_cpu_start(int cpu, void (*fn) (void), long sp, long gp, long a1) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_CPUCTL; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_cpuctl_t); - xiocb.plist.xiocb_cpuctl.cpu_number = cpu; - xiocb.plist.xiocb_cpuctl.cpu_command = CFE_CPU_CMD_START; - xiocb.plist.xiocb_cpuctl.gp_val = gp; - xiocb.plist.xiocb_cpuctl.sp_val = sp; - xiocb.plist.xiocb_cpuctl.a1_val = a1; - xiocb.plist.xiocb_cpuctl.start_addr = (long) fn; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_cpu_start || CFE_API_ALL */ - -#if defined(CFE_API_cpu_stop) || defined(CFE_API_ALL) -int cfe_cpu_stop(int cpu) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_CPUCTL; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_cpuctl_t); - xiocb.plist.xiocb_cpuctl.cpu_number = cpu; - xiocb.plist.xiocb_cpuctl.cpu_command = CFE_CPU_CMD_STOP; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_cpu_stop || CFE_API_ALL */ - -#if defined(CFE_API_enumenv) || defined(CFE_API_ALL) -int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_ENV_SET; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_envbuf_t); - xiocb.plist.xiocb_envbuf.enum_idx = idx; - xiocb.plist.xiocb_envbuf.name_ptr = XPTR_FROM_NATIVE(name); - xiocb.plist.xiocb_envbuf.name_length = namelen; - xiocb.plist.xiocb_envbuf.val_ptr = XPTR_FROM_NATIVE(val); - xiocb.plist.xiocb_envbuf.val_length = vallen; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_enumenv || CFE_API_ALL */ - -#if defined(CFE_API_enummem) || defined(CFE_API_ALL) -int -cfe_enummem(int idx, int flags, cfe_xuint_t * start, cfe_xuint_t * length, - cfe_xuint_t * type) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_MEMENUM; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = flags; - xiocb.xiocb_psize = sizeof(xiocb_meminfo_t); - xiocb.plist.xiocb_meminfo.mi_idx = idx; - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - - *start = xiocb.plist.xiocb_meminfo.mi_addr; - *length = xiocb.plist.xiocb_meminfo.mi_size; - *type = xiocb.plist.xiocb_meminfo.mi_type; - - return 0; -} -#endif /* CFE_API_enummem || CFE_API_ALL */ - -#if defined(CFE_API_exit) || defined(CFE_API_ALL) -int cfe_exit(int warm, int status) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_RESTART; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = warm ? CFE_FLG_WARMSTART : 0; - xiocb.xiocb_psize = sizeof(xiocb_exitstat_t); - xiocb.plist.xiocb_exitstat.status = status; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_exit || CFE_API_ALL */ - -#if defined(CFE_API_flushcache) || defined(CFE_API_ALL) -int cfe_flushcache(int flg) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_FLUSHCACHE; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = flg; - xiocb.xiocb_psize = 0; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_flushcache || CFE_API_ALL */ - -#if defined(CFE_API_getdevinfo) || defined(CFE_API_ALL) -int cfe_getdevinfo(char *name) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_GETINFO; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_buffer_t); - xiocb.plist.xiocb_buffer.buf_offset = 0; - xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(name); - xiocb.plist.xiocb_buffer.buf_length = cfe_strlen(name); - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - return xiocb.plist.xiocb_buffer.buf_devflags; -} -#endif /* CFE_API_getdevinfo || CFE_API_ALL */ - -#if defined(CFE_API_getenv) || defined(CFE_API_ALL) -int cfe_getenv(char *name, char *dest, int destlen) -{ - cfe_xiocb_t xiocb; - - *dest = 0; - - xiocb.xiocb_fcode = CFE_CMD_ENV_GET; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_envbuf_t); - xiocb.plist.xiocb_envbuf.enum_idx = 0; - xiocb.plist.xiocb_envbuf.name_ptr = XPTR_FROM_NATIVE(name); - xiocb.plist.xiocb_envbuf.name_length = cfe_strlen(name); - xiocb.plist.xiocb_envbuf.val_ptr = XPTR_FROM_NATIVE(dest); - xiocb.plist.xiocb_envbuf.val_length = destlen; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_getenv || CFE_API_ALL */ - -#if defined(CFE_API_getfwinfo) || defined(CFE_API_ALL) -int cfe_getfwinfo(cfe_fwinfo_t * info) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_GETINFO; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_fwinfo_t); - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - - info->fwi_version = xiocb.plist.xiocb_fwinfo.fwi_version; - info->fwi_totalmem = xiocb.plist.xiocb_fwinfo.fwi_totalmem; - info->fwi_flags = xiocb.plist.xiocb_fwinfo.fwi_flags; - info->fwi_boardid = xiocb.plist.xiocb_fwinfo.fwi_boardid; - info->fwi_bootarea_va = xiocb.plist.xiocb_fwinfo.fwi_bootarea_va; - info->fwi_bootarea_pa = xiocb.plist.xiocb_fwinfo.fwi_bootarea_pa; - info->fwi_bootarea_size = - xiocb.plist.xiocb_fwinfo.fwi_bootarea_size; -#if 0 - info->fwi_reserved1 = xiocb.plist.xiocb_fwinfo.fwi_reserved1; - info->fwi_reserved2 = xiocb.plist.xiocb_fwinfo.fwi_reserved2; - info->fwi_reserved3 = xiocb.plist.xiocb_fwinfo.fwi_reserved3; -#endif - - return 0; -} -#endif /* CFE_API_getfwinfo || CFE_API_ALL */ - -#if defined(CFE_API_getstdhandle) || defined(CFE_API_ALL) -int cfe_getstdhandle(int flg) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_GETHANDLE; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = flg; - xiocb.xiocb_psize = 0; - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - return xiocb.xiocb_handle; -} -#endif /* CFE_API_getstdhandle || CFE_API_ALL */ - -#if defined(CFE_API_getticks) || defined(CFE_API_ALL) -int64_t -#ifdef CFE_API_IMPL_NAMESPACE -__cfe_getticks(void) -#else -cfe_getticks(void) -#endif -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_FW_GETTIME; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_time_t); - xiocb.plist.xiocb_time.ticks = 0; - - cfe_iocb_dispatch(&xiocb); - - return xiocb.plist.xiocb_time.ticks; - -} -#endif /* CFE_API_getticks || CFE_API_ALL */ - -#if defined(CFE_API_inpstat) || defined(CFE_API_ALL) -int cfe_inpstat(int handle) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_INPSTAT; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = handle; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_inpstat_t); - xiocb.plist.xiocb_inpstat.inp_status = 0; - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - return xiocb.plist.xiocb_inpstat.inp_status; -} -#endif /* CFE_API_inpstat || CFE_API_ALL */ - -#if defined(CFE_API_ioctl) || defined(CFE_API_ALL) -int -cfe_ioctl(int handle, unsigned int ioctlnum, unsigned char *buffer, - int length, int *retlen, cfe_xuint_t offset) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_IOCTL; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = handle; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_buffer_t); - xiocb.plist.xiocb_buffer.buf_offset = offset; - xiocb.plist.xiocb_buffer.buf_ioctlcmd = ioctlnum; - xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(buffer); - xiocb.plist.xiocb_buffer.buf_length = length; - - cfe_iocb_dispatch(&xiocb); - - if (retlen) - *retlen = xiocb.plist.xiocb_buffer.buf_retlen; - return xiocb.xiocb_status; -} -#endif /* CFE_API_ioctl || CFE_API_ALL */ - -#if defined(CFE_API_open) || defined(CFE_API_ALL) -int cfe_open(char *name) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_OPEN; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_buffer_t); - xiocb.plist.xiocb_buffer.buf_offset = 0; - xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(name); - xiocb.plist.xiocb_buffer.buf_length = cfe_strlen(name); - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - return xiocb.xiocb_handle; -} -#endif /* CFE_API_open || CFE_API_ALL */ - -#if defined(CFE_API_read) || defined(CFE_API_ALL) -int cfe_read(int handle, unsigned char *buffer, int length) -{ - return cfe_readblk(handle, 0, buffer, length); -} -#endif /* CFE_API_read || CFE_API_ALL */ - -#if defined(CFE_API_readblk) || defined(CFE_API_ALL) -int -cfe_readblk(int handle, cfe_xint_t offset, unsigned char *buffer, - int length) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_READ; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = handle; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_buffer_t); - xiocb.plist.xiocb_buffer.buf_offset = offset; - xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(buffer); - xiocb.plist.xiocb_buffer.buf_length = length; - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - return xiocb.plist.xiocb_buffer.buf_retlen; -} -#endif /* CFE_API_readblk || CFE_API_ALL */ - -#if defined(CFE_API_setenv) || defined(CFE_API_ALL) -int cfe_setenv(char *name, char *val) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_ENV_SET; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = 0; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_envbuf_t); - xiocb.plist.xiocb_envbuf.enum_idx = 0; - xiocb.plist.xiocb_envbuf.name_ptr = XPTR_FROM_NATIVE(name); - xiocb.plist.xiocb_envbuf.name_length = cfe_strlen(name); - xiocb.plist.xiocb_envbuf.val_ptr = XPTR_FROM_NATIVE(val); - xiocb.plist.xiocb_envbuf.val_length = cfe_strlen(val); - - cfe_iocb_dispatch(&xiocb); - - return xiocb.xiocb_status; -} -#endif /* CFE_API_setenv || CFE_API_ALL */ - -#if (defined(CFE_API_strlen) || defined(CFE_API_ALL)) \ - && !defined(CFE_API_STRLEN_CUSTOM) -int cfe_strlen(char *name) -{ - int count = 0; - - while (*name++) - count++; - - return count; -} -#endif /* CFE_API_strlen || CFE_API_ALL */ - -#if defined(CFE_API_write) || defined(CFE_API_ALL) -int cfe_write(int handle, unsigned char *buffer, int length) -{ - return cfe_writeblk(handle, 0, buffer, length); -} -#endif /* CFE_API_write || CFE_API_ALL */ - -#if defined(CFE_API_writeblk) || defined(CFE_API_ALL) -int -cfe_writeblk(int handle, cfe_xint_t offset, unsigned char *buffer, - int length) -{ - cfe_xiocb_t xiocb; - - xiocb.xiocb_fcode = CFE_CMD_DEV_WRITE; - xiocb.xiocb_status = 0; - xiocb.xiocb_handle = handle; - xiocb.xiocb_flags = 0; - xiocb.xiocb_psize = sizeof(xiocb_buffer_t); - xiocb.plist.xiocb_buffer.buf_offset = offset; - xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(buffer); - xiocb.plist.xiocb_buffer.buf_length = length; - - cfe_iocb_dispatch(&xiocb); - - if (xiocb.xiocb_status < 0) - return xiocb.xiocb_status; - return xiocb.plist.xiocb_buffer.buf_retlen; -} -#endif /* CFE_API_writeblk || CFE_API_ALL */ diff --git a/arch/mips/sibyte/cfe/cfe_api.h b/arch/mips/sibyte/cfe/cfe_api.h deleted file mode 100644 index d8230cc53b8..00000000000 --- a/arch/mips/sibyte/cfe/cfe_api.h +++ /dev/null @@ -1,185 +0,0 @@ -/* - * Copyright (C) 2000, 2001, 2002 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* ********************************************************************* - * - * Broadcom Common Firmware Environment (CFE) - * - * Device function prototypes File: cfe_api.h - * - * This file contains declarations for doing callbacks to - * cfe from an application. It should be the only header - * needed by the application to use this library - * - * Authors: Mitch Lichtenberg, Chris Demetriou - * - ********************************************************************* */ - -#ifndef CFE_API_H -#define CFE_API_H - -/* - * Apply customizations here for different OSes. These need to: - * * typedef uint64_t, int64_t, intptr_t, uintptr_t. - * * define cfe_strlen() if use of an existing function is desired. - * * define CFE_API_IMPL_NAMESPACE if API functions are to use - * names in the implementation namespace. - * Also, optionally, if the build environment does not do so automatically, - * CFE_API_* can be defined here as desired. - */ -/* Begin customization. */ -#include <linux/types.h> -#include <linux/string.h> - -typedef long intptr_t; - -#define cfe_strlen strlen - -#define CFE_API_ALL -#define CFE_API_STRLEN_CUSTOM -/* End customization. */ - - -/* ********************************************************************* - * Constants - ********************************************************************* */ - -/* Seal indicating CFE's presence, passed to user program. */ -#define CFE_EPTSEAL 0x43464531 - -#define CFE_MI_RESERVED 0 /* memory is reserved, do not use */ -#define CFE_MI_AVAILABLE 1 /* memory is available */ - -#define CFE_FLG_WARMSTART 0x00000001 -#define CFE_FLG_FULL_ARENA 0x00000001 -#define CFE_FLG_ENV_PERMANENT 0x00000001 - -#define CFE_CPU_CMD_START 1 -#define CFE_CPU_CMD_STOP 0 - -#define CFE_STDHANDLE_CONSOLE 0 - -#define CFE_DEV_NETWORK 1 -#define CFE_DEV_DISK 2 -#define CFE_DEV_FLASH 3 -#define CFE_DEV_SERIAL 4 -#define CFE_DEV_CPU 5 -#define CFE_DEV_NVRAM 6 -#define CFE_DEV_CLOCK 7 -#define CFE_DEV_OTHER 8 -#define CFE_DEV_MASK 0x0F - -#define CFE_CACHE_FLUSH_D 1 -#define CFE_CACHE_INVAL_I 2 -#define CFE_CACHE_INVAL_D 4 -#define CFE_CACHE_INVAL_L2 8 - -#define CFE_FWI_64BIT 0x00000001 -#define CFE_FWI_32BIT 0x00000002 -#define CFE_FWI_RELOC 0x00000004 -#define CFE_FWI_UNCACHED 0x00000008 -#define CFE_FWI_MULTICPU 0x00000010 -#define CFE_FWI_FUNCSIM 0x00000020 -#define CFE_FWI_RTLSIM 0x00000040 - -typedef struct { - int64_t fwi_version; /* major, minor, eco version */ - int64_t fwi_totalmem; /* total installed mem */ - int64_t fwi_flags; /* various flags */ - int64_t fwi_boardid; /* board ID */ - int64_t fwi_bootarea_va; /* VA of boot area */ - int64_t fwi_bootarea_pa; /* PA of boot area */ - int64_t fwi_bootarea_size; /* size of boot area */ -} cfe_fwinfo_t; - - -/* - * cfe_strlen is handled specially: If already defined, it has been - * overridden in this environment with a standard strlen-like function. - */ -#ifdef cfe_strlen -# define CFE_API_STRLEN_CUSTOM -#else -# ifdef CFE_API_IMPL_NAMESPACE -# define cfe_strlen(a) __cfe_strlen(a) -# endif -int cfe_strlen(char *name); -#endif - -/* - * Defines and prototypes for functions which take no arguments. - */ -#ifdef CFE_API_IMPL_NAMESPACE -int64_t __cfe_getticks(void); -#define cfe_getticks() __cfe_getticks() -#else -int64_t cfe_getticks(void); -#endif - -/* - * Defines and prototypes for the rest of the functions. - */ -#ifdef CFE_API_IMPL_NAMESPACE -#define cfe_close(a) __cfe_close(a) -#define cfe_cpu_start(a,b,c,d,e) __cfe_cpu_start(a,b,c,d,e) -#define cfe_cpu_stop(a) __cfe_cpu_stop(a) -#define cfe_enumenv(a,b,d,e,f) __cfe_enumenv(a,b,d,e,f) -#define cfe_enummem(a,b,c,d,e) __cfe_enummem(a,b,c,d,e) -#define cfe_exit(a,b) __cfe_exit(a,b) -#define cfe_flushcache(a) __cfe_cacheflush(a) -#define cfe_getdevinfo(a) __cfe_getdevinfo(a) -#define cfe_getenv(a,b,c) __cfe_getenv(a,b,c) -#define cfe_getfwinfo(a) __cfe_getfwinfo(a) -#define cfe_getstdhandle(a) __cfe_getstdhandle(a) -#define cfe_init(a,b) __cfe_init(a,b) -#define cfe_inpstat(a) __cfe_inpstat(a) -#define cfe_ioctl(a,b,c,d,e,f) __cfe_ioctl(a,b,c,d,e,f) -#define cfe_open(a) __cfe_open(a) -#define cfe_read(a,b,c) __cfe_read(a,b,c) -#define cfe_readblk(a,b,c,d) __cfe_readblk(a,b,c,d) -#define cfe_setenv(a,b) __cfe_setenv(a,b) -#define cfe_write(a,b,c) __cfe_write(a,b,c) -#define cfe_writeblk(a,b,c,d) __cfe_writeblk(a,b,c,d) -#endif /* CFE_API_IMPL_NAMESPACE */ - -int cfe_close(int handle); -int cfe_cpu_start(int cpu, void (*fn) (void), long sp, long gp, long a1); -int cfe_cpu_stop(int cpu); -int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen); -int cfe_enummem(int idx, int flags, uint64_t * start, uint64_t * length, - uint64_t * type); -int cfe_exit(int warm, int status); -int cfe_flushcache(int flg); -int cfe_getdevinfo(char *name); -int cfe_getenv(char *name, char *dest, int destlen); -int cfe_getfwinfo(cfe_fwinfo_t * info); -int cfe_getstdhandle(int flg); -int cfe_init(uint64_t handle, uint64_t ept); -int cfe_inpstat(int handle); -int cfe_ioctl(int handle, unsigned int ioctlnum, unsigned char *buffer, - int length, int *retlen, uint64_t offset); -int cfe_open(char *name); -int cfe_read(int handle, unsigned char *buffer, int length); -int cfe_readblk(int handle, int64_t offset, unsigned char *buffer, - int length); -int cfe_setenv(char *name, char *val); -int cfe_write(int handle, unsigned char *buffer, int length); -int cfe_writeblk(int handle, int64_t offset, unsigned char *buffer, - int length); - -#endif /* CFE_API_H */ diff --git a/arch/mips/sibyte/cfe/cfe_api_int.h b/arch/mips/sibyte/cfe/cfe_api_int.h deleted file mode 100644 index f7e5a64b55f..00000000000 --- a/arch/mips/sibyte/cfe/cfe_api_int.h +++ /dev/null @@ -1,152 +0,0 @@ -/* - * Copyright (C) 2000, 2001, 2002 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* ********************************************************************* - * - * Broadcom Common Firmware Environment (CFE) - * - * Device function prototypes File: cfe_api_int.h - * - * This header defines all internal types and macros for the - * library. This is stuff that's not exported to an app - * using the library. - * - * Authors: Mitch Lichtenberg, Chris Demetriou - * - ********************************************************************* */ - -#ifndef CFE_API_INT_H -#define CFE_API_INT_H - -/* ********************************************************************* - * Constants - ********************************************************************* */ - -#define CFE_CMD_FW_GETINFO 0 -#define CFE_CMD_FW_RESTART 1 -#define CFE_CMD_FW_BOOT 2 -#define CFE_CMD_FW_CPUCTL 3 -#define CFE_CMD_FW_GETTIME 4 -#define CFE_CMD_FW_MEMENUM 5 -#define CFE_CMD_FW_FLUSHCACHE 6 - -#define CFE_CMD_DEV_GETHANDLE 9 -#define CFE_CMD_DEV_ENUM 10 -#define CFE_CMD_DEV_OPEN 11 -#define CFE_CMD_DEV_INPSTAT 12 -#define CFE_CMD_DEV_READ 13 -#define CFE_CMD_DEV_WRITE 14 -#define CFE_CMD_DEV_IOCTL 15 -#define CFE_CMD_DEV_CLOSE 16 -#define CFE_CMD_DEV_GETINFO 17 - -#define CFE_CMD_ENV_ENUM 20 -#define CFE_CMD_ENV_GET 22 -#define CFE_CMD_ENV_SET 23 -#define CFE_CMD_ENV_DEL 24 - -#define CFE_CMD_MAX 32 - -#define CFE_CMD_VENDOR_USE 0x8000 /* codes above this are for customer use */ - -/* ********************************************************************* - * Structures - ********************************************************************* */ - -typedef uint64_t cfe_xuint_t; -typedef int64_t cfe_xint_t; -typedef int64_t cfe_xptr_t; - -typedef struct xiocb_buffer_s { - cfe_xuint_t buf_offset; /* offset on device (bytes) */ - cfe_xptr_t buf_ptr; /* pointer to a buffer */ - cfe_xuint_t buf_length; /* length of this buffer */ - cfe_xuint_t buf_retlen; /* returned length (for read ops) */ - cfe_xuint_t buf_ioctlcmd; /* IOCTL command (used only for IOCTLs) */ -} xiocb_buffer_t; - -#define buf_devflags buf_ioctlcmd /* returned device info flags */ - -typedef struct xiocb_inpstat_s { - cfe_xuint_t inp_status; /* 1 means input available */ -} xiocb_inpstat_t; - -typedef struct xiocb_envbuf_s { - cfe_xint_t enum_idx; /* 0-based enumeration index */ - cfe_xptr_t name_ptr; /* name string buffer */ - cfe_xint_t name_length; /* size of name buffer */ - cfe_xptr_t val_ptr; /* value string buffer */ - cfe_xint_t val_length; /* size of value string buffer */ -} xiocb_envbuf_t; - -typedef struct xiocb_cpuctl_s { - cfe_xuint_t cpu_number; /* cpu number to control */ - cfe_xuint_t cpu_command; /* command to issue to CPU */ - cfe_xuint_t start_addr; /* CPU start address */ - cfe_xuint_t gp_val; /* starting GP value */ - cfe_xuint_t sp_val; /* starting SP value */ - cfe_xuint_t a1_val; /* starting A1 value */ -} xiocb_cpuctl_t; - -typedef struct xiocb_time_s { - cfe_xint_t ticks; /* current time in ticks */ -} xiocb_time_t; - -typedef struct xiocb_exitstat_s { - cfe_xint_t status; -} xiocb_exitstat_t; - -typedef struct xiocb_meminfo_s { - cfe_xint_t mi_idx; /* 0-based enumeration index */ - cfe_xint_t mi_type; /* type of memory block */ - cfe_xuint_t mi_addr; /* physical start address */ - cfe_xuint_t mi_size; /* block size */ -} xiocb_meminfo_t; - -typedef struct xiocb_fwinfo_s { - cfe_xint_t fwi_version; /* major, minor, eco version */ - cfe_xint_t fwi_totalmem; /* total installed mem */ - cfe_xint_t fwi_flags; /* various flags */ - cfe_xint_t fwi_boardid; /* board ID */ - cfe_xint_t fwi_bootarea_va; /* VA of boot area */ - cfe_xint_t fwi_bootarea_pa; /* PA of boot area */ - cfe_xint_t fwi_bootarea_size; /* size of boot area */ - cfe_xint_t fwi_reserved1; - cfe_xint_t fwi_reserved2; - cfe_xint_t fwi_reserved3; -} xiocb_fwinfo_t; - -typedef struct cfe_xiocb_s { - cfe_xuint_t xiocb_fcode; /* IOCB function code */ - cfe_xint_t xiocb_status; /* return status */ - cfe_xint_t xiocb_handle; /* file/device handle */ - cfe_xuint_t xiocb_flags; /* flags for this IOCB */ - cfe_xuint_t xiocb_psize; /* size of parameter list */ - union { - xiocb_buffer_t xiocb_buffer; /* buffer parameters */ - xiocb_inpstat_t xiocb_inpstat; /* input status parameters */ - xiocb_envbuf_t xiocb_envbuf; /* environment function parameters */ - xiocb_cpuctl_t xiocb_cpuctl; /* CPU control parameters */ - xiocb_time_t xiocb_time; /* timer parameters */ - xiocb_meminfo_t xiocb_meminfo; /* memory arena info parameters */ - xiocb_fwinfo_t xiocb_fwinfo; /* firmware information */ - xiocb_exitstat_t xiocb_exitstat; /* Exit Status */ - } plist; -} cfe_xiocb_t; - -#endif /* CFE_API_INT_H */ diff --git a/arch/mips/sibyte/cfe/cfe_error.h b/arch/mips/sibyte/cfe/cfe_error.h deleted file mode 100644 index 975f00002cb..00000000000 --- a/arch/mips/sibyte/cfe/cfe_error.h +++ /dev/null @@ -1,85 +0,0 @@ -/* - * Copyright (C) 2000, 2001, 2002 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* ********************************************************************* - * - * Broadcom Common Firmware Environment (CFE) - * - * Error codes File: cfe_error.h - * - * CFE's global error code list is here. - * - * Author: Mitch Lichtenberg - * - ********************************************************************* */ - - -#define CFE_OK 0 -#define CFE_ERR -1 /* generic error */ -#define CFE_ERR_INV_COMMAND -2 -#define CFE_ERR_EOF -3 -#define CFE_ERR_IOERR -4 -#define CFE_ERR_NOMEM -5 -#define CFE_ERR_DEVNOTFOUND -6 -#define CFE_ERR_DEVOPEN -7 -#define CFE_ERR_INV_PARAM -8 -#define CFE_ERR_ENVNOTFOUND -9 -#define CFE_ERR_ENVREADONLY -10 - -#define CFE_ERR_NOTELF -11 -#define CFE_ERR_NOT32BIT -12 -#define CFE_ERR_WRONGENDIAN -13 -#define CFE_ERR_BADELFVERS -14 -#define CFE_ERR_NOTMIPS -15 -#define CFE_ERR_BADELFFMT -16 -#define CFE_ERR_BADADDR -17 - -#define CFE_ERR_FILENOTFOUND -18 -#define CFE_ERR_UNSUPPORTED -19 - -#define CFE_ERR_HOSTUNKNOWN -20 - -#define CFE_ERR_TIMEOUT -21 - -#define CFE_ERR_PROTOCOLERR -22 - -#define CFE_ERR_NETDOWN -23 -#define CFE_ERR_NONAMESERVER -24 - -#define CFE_ERR_NOHANDLES -25 -#define CFE_ERR_ALREADYBOUND -26 - -#define CFE_ERR_CANNOTSET -27 -#define CFE_ERR_NOMORE -28 -#define CFE_ERR_BADFILESYS -29 -#define CFE_ERR_FSNOTAVAIL -30 - -#define CFE_ERR_INVBOOTBLOCK -31 -#define CFE_ERR_WRONGDEVTYPE -32 -#define CFE_ERR_BBCHECKSUM -33 -#define CFE_ERR_BOOTPROGCHKSUM -34 - -#define CFE_ERR_LDRNOTAVAIL -35 - -#define CFE_ERR_NOTREADY -36 - -#define CFE_ERR_GETMEM -37 -#define CFE_ERR_SETMEM -38 - -#define CFE_ERR_NOTCONN -39 -#define CFE_ERR_ADDRINUSE -40 diff --git a/arch/mips/sibyte/cfe/smp.c b/arch/mips/sibyte/cfe/smp.c deleted file mode 100644 index eab20e2db32..00000000000 --- a/arch/mips/sibyte/cfe/smp.c +++ /dev/null @@ -1,110 +0,0 @@ -/* - * Copyright (C) 2000, 2001, 2002, 2003 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -#include <linux/init.h> -#include <linux/sched.h> -#include <linux/smp.h> -#include <asm/processor.h> - -#include "cfe_api.h" -#include "cfe_error.h" - -/* - * Use CFE to find out how many CPUs are available, setting up - * phys_cpu_present_map and the logical/physical mappings. - * XXXKW will the boot CPU ever not be physical 0? - * - * Common setup before any secondaries are started - */ -void __init plat_smp_setup(void) -{ - int i, num; - - cpus_clear(phys_cpu_present_map); - cpu_set(0, phys_cpu_present_map); - __cpu_number_map[0] = 0; - __cpu_logical_map[0] = 0; - - for (i = 1, num = 0; i < NR_CPUS; i++) { - if (cfe_cpu_stop(i) == 0) { - cpu_set(i, phys_cpu_present_map); - __cpu_number_map[i] = ++num; - __cpu_logical_map[num] = i; - } - } - printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num); -} - -void __init plat_prepare_cpus(unsigned int max_cpus) -{ -} - -/* - * Setup the PC, SP, and GP of a secondary processor and start it - * running! - */ -void prom_boot_secondary(int cpu, struct task_struct *idle) -{ - int retval; - - retval = cfe_cpu_start(cpu_logical_map(cpu), &smp_bootstrap, - __KSTK_TOS(idle), - (unsigned long)task_thread_info(idle), 0); - if (retval != 0) - printk("cfe_start_cpu(%i) returned %i\n" , cpu, retval); -} - -/* - * Code to run on secondary just after probing the CPU - */ -void prom_init_secondary(void) -{ -#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) - extern void bcm1480_smp_init(void); - bcm1480_smp_init(); -#elif defined(CONFIG_SIBYTE_SB1250) - extern void sb1250_smp_init(void); - sb1250_smp_init(); -#else -#error invalid SMP configuration -#endif -} - -/* - * Do any tidying up before marking online and running the idle - * loop - */ -void prom_smp_finish(void) -{ -#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) - extern void bcm1480_smp_finish(void); - bcm1480_smp_finish(); -#elif defined(CONFIG_SIBYTE_SB1250) - extern void sb1250_smp_finish(void); - sb1250_smp_finish(); -#else -#error invalid SMP configuration -#endif -} - -/* - * Final cleanup after all secondaries booted - */ -void prom_cpus_done(void) -{ -} diff --git a/arch/mips/sibyte/common/Makefile b/arch/mips/sibyte/common/Makefile index 8a06a4fb521..b3d6bf23a66 100644 --- a/arch/mips/sibyte/common/Makefile +++ b/arch/mips/sibyte/common/Makefile @@ -1,5 +1,4 @@ -obj-y := - +obj-y := cfe.o +obj-$(CONFIG_SIBYTE_BUS_WATCHER) += bus_watcher.o +obj-$(CONFIG_SIBYTE_CFE_CONSOLE) += cfe_console.o obj-$(CONFIG_SIBYTE_TBPROF) += sb_tbprof.o - -EXTRA_AFLAGS := $(CFLAGS) diff --git a/arch/mips/sibyte/sb1250/bus_watcher.c b/arch/mips/sibyte/common/bus_watcher.c index 45274bd3cd8..5581844c919 100644 --- a/arch/mips/sibyte/sb1250/bus_watcher.c +++ b/arch/mips/sibyte/common/bus_watcher.c @@ -30,13 +30,16 @@ #include <linux/interrupt.h> #include <linux/sched.h> #include <linux/proc_fs.h> -#include <asm/system.h> +#include <linux/seq_file.h> #include <asm/io.h> #include <asm/sibyte/sb1250.h> #include <asm/sibyte/sb1250_regs.h> #include <asm/sibyte/sb1250_int.h> #include <asm/sibyte/sb1250_scd.h> +#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) +#include <asm/sibyte/bcm1480_regs.h> +#endif struct bw_stats_struct { @@ -72,7 +75,7 @@ static void print_summary(uint32_t status, uint32_t l2_err, * already been destructively read out of the registers. * * notes: this is currently used by the cache error handler - * should provide locking against the interrupt handler + * should provide locking against the interrupt handler */ void check_bus_watcher(void) { @@ -81,9 +84,15 @@ void check_bus_watcher(void) #ifdef CONFIG_SB1_PASS_1_WORKAROUNDS /* Destructive read, clears register and interrupt */ status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS)); -#else +#elif defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250) /* Use non-destructive register */ status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS_DEBUG)); +#elif defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) + /* Use non-destructive register */ + /* Same as 1250 except BUS_ERR_STATUS_DEBUG is in a different place. */ + status = csr_in32(IOADDR(A_BCM1480_BUS_ERR_STATUS_DEBUG)); +#else +#error bus watcher being built for unknown Sibyte SOC! #endif if (!(status & 0x7fffffff)) { printk("Using last values reaped by bus watcher driver\n"); @@ -100,63 +109,60 @@ void check_bus_watcher(void) printk("Bus watcher indicates no error\n"); } -static int bw_print_buffer(char *page, struct bw_stats_struct *stats) +#ifdef CONFIG_PROC_FS + +/* For simplicity, I want to assume a single read is required each + time */ +static int bw_proc_show(struct seq_file *m, void *v) { - int len; - - len = sprintf(page, "SiByte Bus Watcher statistics\n"); - len += sprintf(page+len, "-----------------------------\n"); - len += sprintf(page+len, "L2-d-cor %8ld\nL2-d-bad %8ld\n", - stats->l2_cor_d, stats->l2_bad_d); - len += sprintf(page+len, "L2-t-cor %8ld\nL2-t-bad %8ld\n", - stats->l2_cor_t, stats->l2_bad_t); - len += sprintf(page+len, "MC-d-cor %8ld\nMC-d-bad %8ld\n", - stats->mem_cor_d, stats->mem_bad_d); - len += sprintf(page+len, "IO-err %8ld\n", stats->bus_error); - len += sprintf(page+len, "\nLast recorded signature:\n"); - len += sprintf(page+len, "Request %02x from %d, answered by %d with Dcode %d\n", - (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f), - (int)(G_SCD_BERR_TID(stats->status) >> 6), - (int)G_SCD_BERR_RID(stats->status), - (int)G_SCD_BERR_DCODE(stats->status)); + struct bw_stats_struct *stats = m->private; + + seq_puts(m, "SiByte Bus Watcher statistics\n"); + seq_puts(m, "-----------------------------\n"); + seq_printf(m, "L2-d-cor %8ld\nL2-d-bad %8ld\n", + stats->l2_cor_d, stats->l2_bad_d); + seq_printf(m, "L2-t-cor %8ld\nL2-t-bad %8ld\n", + stats->l2_cor_t, stats->l2_bad_t); + seq_printf(m, "MC-d-cor %8ld\nMC-d-bad %8ld\n", + stats->mem_cor_d, stats->mem_bad_d); + seq_printf(m, "IO-err %8ld\n", stats->bus_error); + seq_puts(m, "\nLast recorded signature:\n"); + seq_printf(m, "Request %02x from %d, answered by %d with Dcode %d\n", + (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f), + (int)(G_SCD_BERR_TID(stats->status) >> 6), + (int)G_SCD_BERR_RID(stats->status), + (int)G_SCD_BERR_DCODE(stats->status)); /* XXXKW indicate multiple errors between printings, or stats - collection (or both)? */ + collection (or both)? */ if (stats->status & M_SCD_BERR_MULTERRS) - len += sprintf(page+len, "Multiple errors observed since last check.\n"); + seq_puts(m, "Multiple errors observed since last check.\n"); if (stats->status_printed) { - len += sprintf(page+len, "(no change since last printing)\n"); + seq_puts(m, "(no change since last printing)\n"); } else { stats->status_printed = 1; } - return len; + return 0; } -#ifdef CONFIG_PROC_FS - -/* For simplicity, I want to assume a single read is required each - time */ -static int bw_read_proc(char *page, char **start, off_t off, - int count, int *eof, void *data) +static int bw_proc_open(struct inode *inode, struct file *file) { - int len; - - if (off == 0) { - len = bw_print_buffer(page, data); - *start = page; - } else { - len = 0; - *eof = 1; - } - return len; + return single_open(file, bw_proc_show, PDE_DATA(inode)); } +static const struct file_operations bw_proc_fops = { + .open = bw_proc_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; + static void create_proc_decoder(struct bw_stats_struct *stats) { struct proc_dir_entry *ent; - ent = create_proc_read_entry("bus_watcher", S_IWUSR | S_IRUGO, NULL, - bw_read_proc, stats); + ent = proc_create_data("bus_watcher", S_IWUSR | S_IRUGO, NULL, + &bw_proc_fops, stats); if (!ent) { printk(KERN_INFO "Unable to initialize bus_watcher /proc entry\n"); return; @@ -169,7 +175,7 @@ static void create_proc_decoder(struct bw_stats_struct *stats) * sibyte_bw_int - handle bus watcher interrupts and accumulate counts * * notes: possible re-entry due to multiple sources - * should check/indicate saturation + * should check/indicate saturation */ static irqreturn_t sibyte_bw_int(int irq, void *data) { @@ -178,9 +184,6 @@ static irqreturn_t sibyte_bw_int(int irq, void *data) #ifdef CONFIG_SIBYTE_BW_TRACE int i; #endif -#ifndef CONFIG_PROC_FS - char bw_buf[1024]; -#endif #ifdef CONFIG_SIBYTE_BW_TRACE csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG)); @@ -211,11 +214,6 @@ static irqreturn_t sibyte_bw_int(int irq, void *data) stats->bus_error += G_SCD_MEM_BUSERR(cntr); csr_out32(0, IOADDR(A_BUS_MEM_IO_ERRORS)); -#ifndef CONFIG_PROC_FS - bw_print_buffer(bw_buf, stats); - printk(bw_buf); -#endif - return IRQ_HANDLED; } diff --git a/arch/mips/sibyte/cfe/setup.c b/arch/mips/sibyte/common/cfe.c index ae4a92c3e52..588e1806a1a 100644 --- a/arch/mips/sibyte/cfe/setup.c +++ b/arch/mips/sibyte/common/cfe.c @@ -28,9 +28,10 @@ #include <asm/bootinfo.h> #include <asm/reboot.h> #include <asm/sibyte/board.h> +#include <asm/smp-ops.h> -#include "cfe_api.h" -#include "cfe_error.h" +#include <asm/fw/cfe/cfe_api.h> +#include <asm/fw/cfe/cfe_error.h> /* Max ram addressable in 32-bit segments */ #ifdef CONFIG_64BIT @@ -58,11 +59,7 @@ int cfe_cons_handle; extern unsigned long initrd_start, initrd_end; #endif -#ifdef CONFIG_KGDB -extern int kgdb_port; -#endif - -static void ATTRIB_NORET cfe_linux_exit(void *arg) +static void __noreturn cfe_linux_exit(void *arg) { int warm = *(int *)arg; @@ -73,7 +70,7 @@ static void ATTRIB_NORET cfe_linux_exit(void *arg) if (!reboot_smp) { /* Get CPU 0 to do the cfe_exit */ reboot_smp = 1; - smp_call_function(cfe_linux_exit, arg, 1, 0); + smp_call_function(cfe_linux_exit, arg, 0); } } else { printk("Passing control back to CFE...\n"); @@ -83,14 +80,14 @@ static void ATTRIB_NORET cfe_linux_exit(void *arg) while (1); } -static void ATTRIB_NORET cfe_linux_restart(char *command) +static void __noreturn cfe_linux_restart(char *command) { static const int zero; cfe_linux_exit((void *)&zero); } -static void ATTRIB_NORET cfe_linux_halt(void) +static void __noreturn cfe_linux_halt(void) { static const int one = 1; @@ -130,8 +127,8 @@ static __init void prom_meminit(void) if ((initrd_pstart > addr) && (initrd_pstart < (addr + size))) { add_memory_region(addr, - initrd_pstart - addr, - BOOT_MEM_RAM); + initrd_pstart - addr, + BOOT_MEM_RAM); rd_flag = 1; } if ((initrd_pend > addr) && @@ -198,7 +195,7 @@ static int __init initrd_setup(char *str) /* *Initrd location comes in the form "<hex size of ramdisk in bytes>@<location in memory>" - * e.g. initrd=3abfd@80010000. This is set up by the loader. + * e.g. initrd=3abfd@80010000. This is set up by the loader. */ for (tmp = str; *tmp != '@'; tmp++) { if (!*tmp) { @@ -232,6 +229,9 @@ static int __init initrd_setup(char *str) #endif +extern struct plat_smp_ops sb_smp_ops; +extern struct plat_smp_ops bcm1480_smp_ops; + /* * prom_init is called just after the cpu type is determined, from setup_arch() */ @@ -242,12 +242,9 @@ void __init prom_init(void) int argc = fw_arg0; char **envp = (char **) fw_arg2; int *prom_vec = (int *) fw_arg3; -#ifdef CONFIG_KGDB - char *arg; -#endif _machine_restart = cfe_linux_restart; - _machine_halt = cfe_linux_halt; + _machine_halt = cfe_linux_halt; pm_power_off = cfe_linux_halt; /* @@ -290,17 +287,8 @@ void __init prom_init(void) * boot console */ cfe_cons_handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE); - if (cfe_getenv("LINUX_CMDLINE", arcs_cmdline, CL_SIZE) < 0) { - if (argc < 0) { - /* - * It's OK for direct boot to not provide a - * command line - */ - strcpy(arcs_cmdline, "root=/dev/ram0 "); -#ifdef CONFIG_SIBYTE_PTSWARM - strcat(arcs_cmdline, "console=ttyS0,115200 "); -#endif - } else { + if (cfe_getenv("LINUX_CMDLINE", arcs_cmdline, COMMAND_LINE_SIZE) < 0) { + if (argc >= 0) { /* The loader should have set the command line */ /* too early for panic to do any good */ printk("LINUX_CMDLINE not defined in cfe."); @@ -308,17 +296,10 @@ void __init prom_init(void) } } -#ifdef CONFIG_KGDB - if ((arg = strstr(arcs_cmdline,"kgdb=duart")) != NULL) - kgdb_port = (arg[10] == '0') ? 0 : 1; - else - kgdb_port = 1; -#endif - #ifdef CONFIG_BLK_DEV_INITRD { char *ptr; - /* Need to find out early whether we've got an initrd. So scan + /* Need to find out early whether we've got an initrd. So scan the list looking now */ for (ptr = arcs_cmdline; *ptr; ptr++) { while (*ptr == ' ') { @@ -337,10 +318,16 @@ void __init prom_init(void) #endif /* CONFIG_BLK_DEV_INITRD */ /* Not sure this is needed, but it's the safe way. */ - arcs_cmdline[CL_SIZE-1] = 0; + arcs_cmdline[COMMAND_LINE_SIZE-1] = 0; - mips_machgroup = MACH_GROUP_SIBYTE; prom_meminit(); + +#if defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250) + register_smp_ops(&sb_smp_ops); +#endif +#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) + register_smp_ops(&bcm1480_smp_ops); +#endif } void __init prom_free_prom_memory(void) diff --git a/arch/mips/sibyte/cfe/console.c b/arch/mips/sibyte/common/cfe_console.c index c6ec748175b..1ad2da103fe 100644 --- a/arch/mips/sibyte/cfe/console.c +++ b/arch/mips/sibyte/common/cfe_console.c @@ -4,8 +4,8 @@ #include <asm/sibyte/board.h> -#include "cfe_api.h" -#include "cfe_error.h" +#include <asm/fw/cfe/cfe_api.h> +#include <asm/fw/cfe/cfe_error.h> extern int cfe_cons_handle; @@ -14,7 +14,7 @@ static void cfe_console_write(struct console *cons, const char *str, { int i, last, written; - for (i=0,last=0; i<count; i++) { + for (i=0, last=0; i<count; i++) { if (!str[i]) /* XXXKW can/should this ever happen? */ return; @@ -46,17 +46,18 @@ static int cfe_console_setup(struct console *cons, char *str) /* XXXKW think about interaction with 'console=' cmdline arg */ /* If none of the console options are configured, the build will break. */ if (cfe_getenv("BOOT_CONSOLE", consdev, 32) >= 0) { -#ifdef CONFIG_SIBYTE_SB1250_DUART +#ifdef CONFIG_SERIAL_SB1250_DUART if (!strcmp(consdev, "uart0")) { setleds("u0cn"); } else if (!strcmp(consdev, "uart1")) { setleds("u1cn"); + } else #endif #ifdef CONFIG_VGA_CONSOLE - } else if (!strcmp(consdev, "pcconsole0")) { - setleds("pccn"); -#endif + if (!strcmp(consdev, "pcconsole0")) { + setleds("pccn"); } else +#endif return -ENODEV; } return 0; diff --git a/arch/mips/sibyte/common/sb_tbprof.c b/arch/mips/sibyte/common/sb_tbprof.c index 4fcdaa8ba51..059e28c8fd9 100644 --- a/arch/mips/sibyte/common/sb_tbprof.c +++ b/arch/mips/sibyte/common/sb_tbprof.c @@ -27,7 +27,7 @@ #include <linux/types.h> #include <linux/init.h> #include <linux/interrupt.h> -#include <linux/slab.h> +#include <linux/sched.h> #include <linux/vmalloc.h> #include <linux/fs.h> #include <linux/errno.h> @@ -44,7 +44,7 @@ #include <asm/sibyte/sb1250_scd.h> #include <asm/sibyte/sb1250_int.h> #else -#error invalid SiByte UART configuation +#error invalid SiByte UART configuration #endif #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) @@ -54,7 +54,6 @@ #define K_INT_PERF_CNT K_BCM1480_INT_PERF_CNT #endif -#include <asm/system.h> #include <asm/uaccess.h> #define SBPROF_TB_MAJOR 240 @@ -154,7 +153,7 @@ static u64 tb_period; static void arm_tb(void) { - u64 scdperfcnt; + u64 scdperfcnt; u64 next = (1ULL << 40) - tb_period; u64 tb_options = M_SCD_TRACE_CFG_FREEZE_FULL; @@ -259,8 +258,8 @@ static irqreturn_t sbprof_pc_intr(int irq, void *dev_id) /* * Requires: Already called zclk_timer_init with a value that won't - * saturate 40 bits. No subsequent use of SCD performance counters - * or trace buffer. + * saturate 40 bits. No subsequent use of SCD performance counters + * or trace buffer. */ static int sbprof_zbprof_start(struct file *filp) @@ -276,8 +275,8 @@ static int sbprof_zbprof_start(struct file *filp) sbp.next_tb_sample = 0; filp->f_pos = 0; - err = request_irq (K_INT_TRACE_FREEZE, sbprof_tb_intr, 0, - DEVNAME " trace freeze", &sbp); + err = request_irq(K_INT_TRACE_FREEZE, sbprof_tb_intr, 0, + DEVNAME " trace freeze", &sbp); if (err) return -EBUSY; @@ -290,8 +289,8 @@ static int sbprof_zbprof_start(struct file *filp) /* * We grab this interrupt to prevent others from trying to use - * it, even though we don't want to service the interrupts - * (they only feed into the trace-on-interrupt mechanism) + * it, even though we don't want to service the interrupts + * (they only feed into the trace-on-interrupt mechanism) */ if (request_irq(K_INT_PERF_CNT, sbprof_pc_intr, 0, DEVNAME " scd perfcnt", &sbp)) { free_irq(K_INT_TRACE_FREEZE, &sbp); @@ -300,7 +299,7 @@ static int sbprof_zbprof_start(struct file *filp) /* * I need the core to mask these, but the interrupt mapper to - * pass them through. I am exploiting my knowledge that + * pass them through. I am exploiting my knowledge that * cp0_status masks out IP[5]. krw */ #if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) @@ -330,7 +329,7 @@ static int sbprof_zbprof_start(struct file *filp) __raw_writeq(0, IOADDR(A_ADDR_TRAP_CFG_3)); /* Initialize Trace Event 0-7 */ - /* when interrupt */ + /* when interrupt */ __raw_writeq(M_SCD_TREVT_INTERRUPT, IOADDR(A_SCD_TRACE_EVENT_0)); __raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_1)); __raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_2)); @@ -411,15 +410,19 @@ static int sbprof_tb_open(struct inode *inode, struct file *filp) return -EBUSY; memset(&sbp, 0, sizeof(struct sbprof_tb)); - sbp.sbprof_tbbuf = vmalloc(MAX_TBSAMPLE_BYTES); - if (!sbp.sbprof_tbbuf) + sbp.sbprof_tbbuf = vzalloc(MAX_TBSAMPLE_BYTES); + if (!sbp.sbprof_tbbuf) { + sbp.open = SB_CLOSED; + wmb(); return -ENOMEM; - memset(sbp.sbprof_tbbuf, 0, MAX_TBSAMPLE_BYTES); + } + init_waitqueue_head(&sbp.tb_sync); init_waitqueue_head(&sbp.tb_read); mutex_init(&sbp.lock); sbp.open = SB_OPEN; + wmb(); return 0; } @@ -429,7 +432,7 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp) int minor; minor = iminor(inode); - if (minor != 0 || !sbp.open) + if (minor != 0 || sbp.open != SB_CLOSED) return -ENODEV; mutex_lock(&sbp.lock); @@ -438,7 +441,8 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp) sbprof_zbprof_stop(); vfree(sbp.sbprof_tbbuf); - sbp.open = 0; + sbp.open = SB_CLOSED; + wmb(); mutex_unlock(&sbp.lock); @@ -476,7 +480,7 @@ static ssize_t sbprof_tb_read(struct file *filp, char *buf, return err; } pr_debug(DEVNAME ": read from sample %d, %d bytes\n", - cur_sample, cur_count); + cur_sample, cur_count); size -= cur_count; sample_left -= cur_count; if (!sample_left) { @@ -537,9 +541,10 @@ static const struct file_operations sbprof_tb_fops = { .open = sbprof_tb_open, .release = sbprof_tb_release, .read = sbprof_tb_read, - .unlocked_ioctl = sbprof_tb_ioctl, + .unlocked_ioctl = sbprof_tb_ioctl, .compat_ioctl = sbprof_tb_ioctl, .mmap = NULL, + .llseek = default_llseek, }; static struct class *tb_class; @@ -565,14 +570,15 @@ static int __init sbprof_tb_init(void) tb_class = tbc; - dev = device_create(tbc, NULL, MKDEV(SBPROF_TB_MAJOR, 0), "tb"); + dev = device_create(tbc, NULL, MKDEV(SBPROF_TB_MAJOR, 0), NULL, "tb"); if (IS_ERR(dev)) { err = PTR_ERR(dev); goto out_class; } tb_dev = dev; - sbp.open = 0; + sbp.open = SB_CLOSED; + wmb(); tb_period = zbbus_mhz * 10000LL; pr_info(DEVNAME ": initialized - tb_period = %lld\n", (long long) tb_period); diff --git a/arch/mips/sibyte/sb1250/Makefile b/arch/mips/sibyte/sb1250/Makefile index df662c61473..cdc4c56c3e2 100644 --- a/arch/mips/sibyte/sb1250/Makefile +++ b/arch/mips/sibyte/sb1250/Makefile @@ -1,5 +1,3 @@ obj-y := setup.o irq.o time.o obj-$(CONFIG_SMP) += smp.o -obj-$(CONFIG_SIBYTE_STANDALONE) += prom.o -obj-$(CONFIG_SIBYTE_BUS_WATCHER) += bus_watcher.o diff --git a/arch/mips/sibyte/sb1250/irq.c b/arch/mips/sibyte/sb1250/irq.c index 0e6a13c0bd0..6d8dba5cf34 100644 --- a/arch/mips/sibyte/sb1250/irq.c +++ b/arch/mips/sibyte/sb1250/irq.c @@ -22,12 +22,11 @@ #include <linux/spinlock.h> #include <linux/smp.h> #include <linux/mm.h> -#include <linux/slab.h> #include <linux/kernel_stat.h> #include <asm/errno.h> #include <asm/signal.h> -#include <asm/system.h> +#include <asm/time.h> #include <asm/io.h> #include <asm/sibyte/sb1250_regs.h> @@ -43,58 +42,27 @@ * for interrupt lines */ - -static void end_sb1250_irq(unsigned int irq); -static void enable_sb1250_irq(unsigned int irq); -static void disable_sb1250_irq(unsigned int irq); -static void ack_sb1250_irq(unsigned int irq); -#ifdef CONFIG_SMP -static void sb1250_set_affinity(unsigned int irq, cpumask_t mask); -#endif - #ifdef CONFIG_SIBYTE_HAS_LDT extern unsigned long ldt_eoi_space; #endif -#ifdef CONFIG_KGDB -static int kgdb_irq; - -/* Default to UART1 */ -int kgdb_port = 1; -#ifdef CONFIG_SIBYTE_SB1250_DUART -extern char sb1250_duart_present[]; -#endif -#endif - -static struct irq_chip sb1250_irq_type = { - .name = "SB1250-IMR", - .ack = ack_sb1250_irq, - .mask = disable_sb1250_irq, - .mask_ack = ack_sb1250_irq, - .unmask = enable_sb1250_irq, - .end = end_sb1250_irq, -#ifdef CONFIG_SMP - .set_affinity = sb1250_set_affinity -#endif -}; - /* Store the CPU id (not the logical number) */ int sb1250_irq_owner[SB1250_NR_IRQS]; -DEFINE_SPINLOCK(sb1250_imr_lock); +static DEFINE_RAW_SPINLOCK(sb1250_imr_lock); void sb1250_mask_irq(int cpu, int irq) { unsigned long flags; u64 cur_ints; - spin_lock_irqsave(&sb1250_imr_lock, flags); + raw_spin_lock_irqsave(&sb1250_imr_lock, flags); cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); cur_ints |= (((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); - spin_unlock_irqrestore(&sb1250_imr_lock, flags); + raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags); } void sb1250_unmask_irq(int cpu, int irq) @@ -102,36 +70,31 @@ void sb1250_unmask_irq(int cpu, int irq) unsigned long flags; u64 cur_ints; - spin_lock_irqsave(&sb1250_imr_lock, flags); + raw_spin_lock_irqsave(&sb1250_imr_lock, flags); cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); cur_ints &= ~(((u64) 1) << irq); ____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); - spin_unlock_irqrestore(&sb1250_imr_lock, flags); + raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags); } #ifdef CONFIG_SMP -static void sb1250_set_affinity(unsigned int irq, cpumask_t mask) +static int sb1250_set_affinity(struct irq_data *d, const struct cpumask *mask, + bool force) { int i = 0, old_cpu, cpu, int_on; + unsigned int irq = d->irq; u64 cur_ints; - struct irq_desc *desc = irq_desc + irq; unsigned long flags; - i = first_cpu(mask); - - if (cpus_weight(mask) > 1) { - printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq); - return; - } + i = cpumask_first_and(mask, cpu_online_mask); /* Convert logical CPU to physical CPU */ cpu = cpu_logical_map(i); /* Protect against other affinity changers and IMR manipulation */ - spin_lock_irqsave(&desc->lock, flags); - spin_lock(&sb1250_imr_lock); + raw_spin_lock_irqsave(&sb1250_imr_lock, flags); /* Swizzle each CPU's IMR (but leave the IP selection alone) */ old_cpu = sb1250_irq_owner[irq]; @@ -153,26 +116,30 @@ static void sb1250_set_affinity(unsigned int irq, cpumask_t mask) ____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) + R_IMR_INTERRUPT_MASK)); } - spin_unlock(&sb1250_imr_lock); - spin_unlock_irqrestore(&desc->lock, flags); + raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags); + + return 0; } #endif -/*****************************************************************************/ - -static void disable_sb1250_irq(unsigned int irq) +static void disable_sb1250_irq(struct irq_data *d) { + unsigned int irq = d->irq; + sb1250_mask_irq(sb1250_irq_owner[irq], irq); } -static void enable_sb1250_irq(unsigned int irq) +static void enable_sb1250_irq(struct irq_data *d) { + unsigned int irq = d->irq; + sb1250_unmask_irq(sb1250_irq_owner[irq], irq); } -static void ack_sb1250_irq(unsigned int irq) +static void ack_sb1250_irq(struct irq_data *d) { + unsigned int irq = d->irq; #ifdef CONFIG_SIBYTE_HAS_LDT u64 pending; @@ -215,61 +182,28 @@ static void ack_sb1250_irq(unsigned int irq) sb1250_mask_irq(sb1250_irq_owner[irq], irq); } - -static void end_sb1250_irq(unsigned int irq) -{ - if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) { - sb1250_unmask_irq(sb1250_irq_owner[irq], irq); - } -} - +static struct irq_chip sb1250_irq_type = { + .name = "SB1250-IMR", + .irq_mask_ack = ack_sb1250_irq, + .irq_unmask = enable_sb1250_irq, + .irq_mask = disable_sb1250_irq, +#ifdef CONFIG_SMP + .irq_set_affinity = sb1250_set_affinity +#endif +}; void __init init_sb1250_irqs(void) { int i; for (i = 0; i < SB1250_NR_IRQS; i++) { - set_irq_chip(i, &sb1250_irq_type); + irq_set_chip_and_handler(i, &sb1250_irq_type, + handle_level_irq); sb1250_irq_owner[i] = 0; } } -static irqreturn_t sb1250_dummy_handler(int irq, void *dev_id) -{ - return IRQ_NONE; -} - -static struct irqaction sb1250_dummy_action = { - .handler = sb1250_dummy_handler, - .flags = 0, - .mask = CPU_MASK_NONE, - .name = "sb1250-private", - .next = NULL, - .dev_id = 0 -}; - -int sb1250_steal_irq(int irq) -{ - struct irq_desc *desc = irq_desc + irq; - unsigned long flags; - int retval = 0; - - if (irq >= SB1250_NR_IRQS) - return -EINVAL; - - spin_lock_irqsave(&desc->lock,flags); - /* Don't allow sharing at all for these */ - if (desc->action != NULL) - retval = -EBUSY; - else { - desc->action = &sb1250_dummy_action; - desc->depth = 0; - } - spin_unlock_irqrestore(&desc->lock,flags); - return 0; -} - /* * arch_init_irq is called early in the boot sequence from init/main.c via * init_IRQ. It is responsible for setting up the interrupt mapper and @@ -287,7 +221,7 @@ int sb1250_steal_irq(int irq) * On the second cpu, everything is set to IP5, which is * ignored, EXCEPT the mailbox interrupt. That one is * set to IP[2] so it is handled. This is needed so we - * can do cross-cpu function calls, as requred by SMP + * can do cross-cpu function calls, as required by SMP */ #define IMR_IP2_VAL K_INT_MAP_I0 @@ -330,7 +264,7 @@ void __init arch_init_irq(void) IOADDR(A_IMR_REGISTER(1, R_IMR_INTERRUPT_MAP_BASE) + (K_INT_MBOX_0 << 3))); - /* Clear the mailboxes. The firmware may leave them dirty */ + /* Clear the mailboxes. The firmware may leave them dirty */ __raw_writeq(0xffffffffffffffffULL, IOADDR(A_IMR_REGISTER(0, R_IMR_MAILBOX_CLR_CPU))); __raw_writeq(0xffffffffffffffffULL, @@ -341,76 +275,39 @@ void __init arch_init_irq(void) __raw_writeq(tmp, IOADDR(A_IMR_REGISTER(0, R_IMR_INTERRUPT_MASK))); __raw_writeq(tmp, IOADDR(A_IMR_REGISTER(1, R_IMR_INTERRUPT_MASK))); - sb1250_steal_irq(K_INT_MBOX_0); - /* * Note that the timer interrupts are also mapped, but this is - * done in sb1250_time_init(). Also, the profiling driver + * done in sb1250_time_init(). Also, the profiling driver * does its own management of IP7. */ -#ifdef CONFIG_KGDB - imask |= STATUSF_IP6; -#endif /* Enable necessary IPs, disable the rest */ change_c0_status(ST0_IM, imask); - -#ifdef CONFIG_KGDB - if (kgdb_flag) { - kgdb_irq = K_INT_UART_0 + kgdb_port; - -#ifdef CONFIG_SIBYTE_SB1250_DUART - sb1250_duart_present[kgdb_port] = 0; -#endif - /* Setup uart 1 settings, mapper */ - __raw_writeq(M_DUART_IMR_BRK, - IOADDR(A_DUART_IMRREG(kgdb_port))); - - sb1250_steal_irq(kgdb_irq); - __raw_writeq(IMR_IP6_VAL, - IOADDR(A_IMR_REGISTER(0, - R_IMR_INTERRUPT_MAP_BASE) + - (kgdb_irq << 3))); - sb1250_unmask_irq(0, kgdb_irq); - } -#endif } -#ifdef CONFIG_KGDB - -#include <linux/delay.h> - -#define duart_out(reg, val) csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port,reg))) -#define duart_in(reg) csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port,reg))) +extern void sb1250_mailbox_interrupt(void); -static void sb1250_kgdb_interrupt(void) +static inline void dispatch_ip2(void) { + unsigned int cpu = smp_processor_id(); + unsigned long long mask; + /* - * Clear break-change status (allow some time for the remote - * host to stop the break, since we would see another - * interrupt on the end-of-break too) + * Default...we've hit an IP[2] interrupt, which means we've got to + * check the 1250 interrupt registers to figure out what to do. Need + * to detect which CPU we're on, now that smp_affinity is supported. */ - kstat_this_cpu.irqs[kgdb_irq]++; - mdelay(500); - duart_out(R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT | - M_DUART_RX_EN | M_DUART_TX_EN); - set_async_breakpoint(&get_irq_regs()->cp0_epc); + mask = __raw_readq(IOADDR(A_IMR_REGISTER(cpu, + R_IMR_INTERRUPT_STATUS_BASE))); + if (mask) + do_IRQ(fls64(mask) - 1); } -#endif /* CONFIG_KGDB */ - -extern void sb1250_timer_interrupt(void); -extern void sb1250_mailbox_interrupt(void); - asmlinkage void plat_irq_dispatch(void) { + unsigned int cpu = smp_processor_id(); unsigned int pending; -#ifdef CONFIG_SIBYTE_SB1250_PROF - /* Set compare to count to silence count/compare timer interrupts */ - write_c0_compare(read_c0_count()); -#endif - /* * What a pain. We have to be really careful saving the upper 32 bits * of any * register across function calls if we don't want them @@ -423,40 +320,18 @@ asmlinkage void plat_irq_dispatch(void) pending = read_c0_cause() & read_c0_status() & ST0_IM; -#ifdef CONFIG_SIBYTE_SB1250_PROF - if (pending & CAUSEF_IP7) /* Cpu performance counter interrupt */ - sbprof_cpu_intr(); - else -#endif - - if (pending & CAUSEF_IP4) - sb1250_timer_interrupt(); + if (pending & CAUSEF_IP7) /* CPU performance counter interrupt */ + do_IRQ(MIPS_CPU_IRQ_BASE + 7); + else if (pending & CAUSEF_IP4) + do_IRQ(K_INT_TIMER_0 + cpu); /* sb1250_timer_interrupt() */ #ifdef CONFIG_SMP else if (pending & CAUSEF_IP3) sb1250_mailbox_interrupt(); #endif -#ifdef CONFIG_KGDB - else if (pending & CAUSEF_IP6) /* KGDB (uart 1) */ - sb1250_kgdb_interrupt(); -#endif - - else if (pending & CAUSEF_IP2) { - unsigned long long mask; - - /* - * Default...we've hit an IP[2] interrupt, which means we've - * got to check the 1250 interrupt registers to figure out what - * to do. Need to detect which CPU we're on, now that - * smp_affinity is supported. - */ - mask = __raw_readq(IOADDR(A_IMR_REGISTER(smp_processor_id(), - R_IMR_INTERRUPT_STATUS_BASE))); - if (mask) - do_IRQ(fls64(mask) - 1); - else - spurious_interrupt(); - } else + else if (pending & CAUSEF_IP2) + dispatch_ip2(); + else spurious_interrupt(); } diff --git a/arch/mips/sibyte/sb1250/prom.c b/arch/mips/sibyte/sb1250/prom.c deleted file mode 100644 index 257c4e67435..00000000000 --- a/arch/mips/sibyte/sb1250/prom.c +++ /dev/null @@ -1,97 +0,0 @@ -/* - * Copyright (C) 2000, 2001 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/mm.h> -#include <linux/blkdev.h> -#include <linux/bootmem.h> -#include <linux/smp.h> -#include <linux/initrd.h> -#include <linux/pm.h> - -#include <asm/bootinfo.h> -#include <asm/reboot.h> - -#define MAX_RAM_SIZE ((CONFIG_SIBYTE_STANDALONE_RAM_SIZE * 1024 * 1024) - 1) - -static __init void prom_meminit(void) -{ -#ifdef CONFIG_BLK_DEV_INITRD - unsigned long initrd_pstart; - unsigned long initrd_pend; - - initrd_pstart = __pa(initrd_start); - initrd_pend = __pa(initrd_end); - if (initrd_start && - ((initrd_pstart > MAX_RAM_SIZE) - || (initrd_pend > MAX_RAM_SIZE))) { - panic("initrd out of addressable memory"); - } - - add_memory_region(0, initrd_pstart, - BOOT_MEM_RAM); - add_memory_region(initrd_pstart, initrd_pend - initrd_pstart, - BOOT_MEM_RESERVED); - add_memory_region(initrd_pend, - (CONFIG_SIBYTE_STANDALONE_RAM_SIZE * 1024 * 1024) - initrd_pend, - BOOT_MEM_RAM); -#else - add_memory_region(0, CONFIG_SIBYTE_STANDALONE_RAM_SIZE * 1024 * 1024, - BOOT_MEM_RAM); -#endif -} - -void prom_cpu0_exit(void *unused) -{ - while (1) ; -} - -static void prom_linux_exit(void) -{ -#ifdef CONFIG_SMP - if (smp_processor_id()) { - smp_call_function(prom_cpu0_exit,NULL,1,1); - } -#endif - while(1); -} - -/* - * prom_init is called just after the cpu type is determined, from setup_arch() - */ -void __init prom_init(void) -{ - _machine_restart = (void (*)(char *))prom_linux_exit; - _machine_halt = prom_linux_exit; - pm_power_off = prom_linux_exit; - - strcpy(arcs_cmdline, "root=/dev/ram0 "); - - mips_machgroup = MACH_GROUP_SIBYTE; - prom_meminit(); -} - -void __init prom_free_prom_memory(void) -{ - /* Not sure what I'm supposed to do here. Nothing, I think */ -} - -void prom_putchar(char c) -{ -} diff --git a/arch/mips/sibyte/sb1250/setup.c b/arch/mips/sibyte/sb1250/setup.c index f4a6169aa0a..3c02b2a77ae 100644 --- a/arch/mips/sibyte/sb1250/setup.c +++ b/arch/mips/sibyte/sb1250/setup.c @@ -22,6 +22,7 @@ #include <linux/string.h> #include <asm/bootinfo.h> +#include <asm/cpu.h> #include <asm/mipsregs.h> #include <asm/io.h> #include <asm/sibyte/sb1250.h> @@ -31,6 +32,7 @@ unsigned int sb1_pass; unsigned int soc_pass; unsigned int soc_type; +EXPORT_SYMBOL(soc_type); unsigned int periph_rev; unsigned int zbbus_mhz; EXPORT_SYMBOL(zbbus_mhz); @@ -39,43 +41,6 @@ static char *soc_str; static char *pass_str; static unsigned int war_pass; /* XXXKW don't overload PASS defines? */ -static inline int setup_bcm1250(void); -static inline int setup_bcm112x(void); - -/* Setup code likely to be common to all SiByte platforms */ - -static int __init sys_rev_decode(void) -{ - int ret = 0; - - war_pass = soc_pass; - switch (soc_type) { - case K_SYS_SOC_TYPE_BCM1250: - case K_SYS_SOC_TYPE_BCM1250_ALT: - case K_SYS_SOC_TYPE_BCM1250_ALT2: - soc_str = "BCM1250"; - ret = setup_bcm1250(); - break; - case K_SYS_SOC_TYPE_BCM1120: - soc_str = "BCM1120"; - ret = setup_bcm112x(); - break; - case K_SYS_SOC_TYPE_BCM1125: - soc_str = "BCM1125"; - ret = setup_bcm112x(); - break; - case K_SYS_SOC_TYPE_BCM1125H: - soc_str = "BCM1125H"; - ret = setup_bcm112x(); - break; - default: - printk("Unknown SOC type %x\n", soc_type); - ret = 1; - break; - } - return ret; -} - static int __init setup_bcm1250(void) { int ret = 0; @@ -119,9 +84,25 @@ static int __init setup_bcm1250(void) } break; } + return ret; } +int sb1250_m3_workaround_needed(void) +{ + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1250: + case K_SYS_SOC_TYPE_BCM1250_ALT: + case K_SYS_SOC_TYPE_BCM1250_ALT2: + case K_SYS_SOC_TYPE_BCM1125: + case K_SYS_SOC_TYPE_BCM1125H: + return soc_pass < K_SYS_REVISION_BCM1250_C0; + + default: + return 0; + } +} + static int __init setup_bcm112x(void) { int ret = 0; @@ -157,6 +138,42 @@ static int __init setup_bcm112x(void) printk("Unknown %s rev %x\n", soc_str, soc_pass); ret = 1; } + + return ret; +} + +/* Setup code likely to be common to all SiByte platforms */ + +static int __init sys_rev_decode(void) +{ + int ret = 0; + + war_pass = soc_pass; + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1250: + case K_SYS_SOC_TYPE_BCM1250_ALT: + case K_SYS_SOC_TYPE_BCM1250_ALT2: + soc_str = "BCM1250"; + ret = setup_bcm1250(); + break; + case K_SYS_SOC_TYPE_BCM1120: + soc_str = "BCM1120"; + ret = setup_bcm112x(); + break; + case K_SYS_SOC_TYPE_BCM1125: + soc_str = "BCM1125"; + ret = setup_bcm112x(); + break; + case K_SYS_SOC_TYPE_BCM1125H: + soc_str = "BCM1125H"; + ret = setup_bcm112x(); + break; + default: + printk("Unknown SOC type %x\n", soc_type); + ret = 1; + break; + } + return ret; } @@ -166,7 +183,7 @@ void __init sb1250_setup(void) int plldiv; int bad_config = 0; - sb1_pass = read_c0_prid() & 0xff; + sb1_pass = read_c0_prid() & PRID_REV_MASK; sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION)); soc_type = SYS_SOC_TYPE(sys_rev); soc_pass = G_SYS_REVISION(sys_rev); @@ -187,8 +204,8 @@ void __init sb1250_setup(void) case K_SYS_REVISION_BCM1250_PASS1: #ifndef CONFIG_SB1_PASS_1_WORKAROUNDS printk("@@@@ This is a BCM1250 A0-A2 (Pass 1) board, " - "and the kernel doesn't have the proper " - "workarounds compiled in. @@@@\n"); + "and the kernel doesn't have the proper " + "workarounds compiled in. @@@@\n"); bad_config = 1; #endif break; @@ -197,28 +214,28 @@ void __init sb1250_setup(void) #if !defined(CONFIG_SB1_PASS_2_WORKAROUNDS) || \ !defined(CONFIG_SB1_PASS_2_1_WORKAROUNDS) printk("@@@@ This is a BCM1250 A3-A10 board, and the " - "kernel doesn't have the proper workarounds " - "compiled in. @@@@\n"); + "kernel doesn't have the proper workarounds " + "compiled in. @@@@\n"); bad_config = 1; #endif #ifdef CONFIG_CPU_HAS_PREFETCH printk("@@@@ Prefetches may be enabled in this kernel, " - "but are buggy on this board. @@@@\n"); + "but are buggy on this board. @@@@\n"); bad_config = 1; #endif break; case K_SYS_REVISION_BCM1250_PASS2_2: #ifndef CONFIG_SB1_PASS_2_WORKAROUNDS printk("@@@@ This is a BCM1250 B1/B2. board, and the " - "kernel doesn't have the proper workarounds " - "compiled in. @@@@\n"); + "kernel doesn't have the proper workarounds " + "compiled in. @@@@\n"); bad_config = 1; #endif #if defined(CONFIG_SB1_PASS_2_1_WORKAROUNDS) || \ !defined(CONFIG_CPU_HAS_PREFETCH) printk("@@@@ This is a BCM1250 B1/B2, but the kernel is " - "conservatively configured for an 'A' stepping. " - "@@@@\n"); + "conservatively configured for an 'A' stepping. " + "@@@@\n"); #endif break; default: diff --git a/arch/mips/sibyte/sb1250/smp.c b/arch/mips/sibyte/sb1250/smp.c index c38e1f34460..c0c4b3f88a0 100644 --- a/arch/mips/sibyte/sb1250/smp.c +++ b/arch/mips/sibyte/sb1250/smp.c @@ -21,9 +21,11 @@ #include <linux/interrupt.h> #include <linux/smp.h> #include <linux/kernel_stat.h> +#include <linux/sched.h> #include <asm/mmu_context.h> #include <asm/io.h> +#include <asm/fw/cfe/cfe_api.h> #include <asm/sibyte/sb1250.h> #include <asm/sibyte/sb1250_regs.h> #include <asm/sibyte/sb1250_int.h> @@ -55,13 +57,6 @@ void sb1250_smp_init(void) change_c0_status(ST0_IM, imask); } -void sb1250_smp_finish(void) -{ - extern void sb1250_time_init(void); - sb1250_time_init(); - local_irq_enable(); -} - /* * These are routines for dealing with the sb1250 smp capabilities * independent of board/firmware @@ -71,27 +66,111 @@ void sb1250_smp_finish(void) * Simple enough; everything is set up, so just poke the appropriate mailbox * register, and we should be set */ -void core_send_ipi(int cpu, unsigned int action) +static void sb1250_send_ipi_single(int cpu, unsigned int action) { __raw_writeq((((u64)action) << 48), mailbox_set_regs[cpu]); } +static inline void sb1250_send_ipi_mask(const struct cpumask *mask, + unsigned int action) +{ + unsigned int i; + + for_each_cpu(i, mask) + sb1250_send_ipi_single(i, action); +} + +/* + * Code to run on secondary just after probing the CPU + */ +static void sb1250_init_secondary(void) +{ + extern void sb1250_smp_init(void); + + sb1250_smp_init(); +} + +/* + * Do any tidying up before marking online and running the idle + * loop + */ +static void sb1250_smp_finish(void) +{ + extern void sb1250_clockevent_init(void); + + sb1250_clockevent_init(); + local_irq_enable(); +} + +/* + * Setup the PC, SP, and GP of a secondary processor and start it + * running! + */ +static void sb1250_boot_secondary(int cpu, struct task_struct *idle) +{ + int retval; + + retval = cfe_cpu_start(cpu_logical_map(cpu), &smp_bootstrap, + __KSTK_TOS(idle), + (unsigned long)task_thread_info(idle), 0); + if (retval != 0) + printk("cfe_start_cpu(%i) returned %i\n" , cpu, retval); +} + +/* + * Use CFE to find out how many CPUs are available, setting up + * cpu_possible_mask and the logical/physical mappings. + * XXXKW will the boot CPU ever not be physical 0? + * + * Common setup before any secondaries are started + */ +static void __init sb1250_smp_setup(void) +{ + int i, num; + + init_cpu_possible(cpumask_of(0)); + __cpu_number_map[0] = 0; + __cpu_logical_map[0] = 0; + + for (i = 1, num = 0; i < NR_CPUS; i++) { + if (cfe_cpu_stop(i) == 0) { + set_cpu_possible(i, true); + __cpu_number_map[i] = ++num; + __cpu_logical_map[num] = i; + } + } + printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num); +} + +static void __init sb1250_prepare_cpus(unsigned int max_cpus) +{ +} + +struct plat_smp_ops sb_smp_ops = { + .send_ipi_single = sb1250_send_ipi_single, + .send_ipi_mask = sb1250_send_ipi_mask, + .init_secondary = sb1250_init_secondary, + .smp_finish = sb1250_smp_finish, + .boot_secondary = sb1250_boot_secondary, + .smp_setup = sb1250_smp_setup, + .prepare_cpus = sb1250_prepare_cpus, +}; + void sb1250_mailbox_interrupt(void) { int cpu = smp_processor_id(); + int irq = K_INT_MBOX_0; unsigned int action; - kstat_this_cpu.irqs[K_INT_MBOX_0]++; + kstat_incr_irq_this_cpu(irq); /* Load the mailbox register to figure out what we're supposed to do */ action = (____raw_readq(mailbox_regs[cpu]) >> 48) & 0xffff; /* Clear the mailbox to clear the interrupt */ ____raw_writeq(((u64)action) << 48, mailbox_clear_regs[cpu]); - /* - * Nothing to do for SMP_RESCHEDULE_YOURSELF; returning from the - * interrupt will do the reschedule for us - */ + if (action & SMP_RESCHEDULE_YOURSELF) + scheduler_ipi(); if (action & SMP_CALL_FUNCTION) smp_call_function_interrupt(); diff --git a/arch/mips/sibyte/sb1250/time.c b/arch/mips/sibyte/sb1250/time.c index 2efffe15ff2..68337bf7a5a 100644 --- a/arch/mips/sibyte/sb1250/time.c +++ b/arch/mips/sibyte/sb1250/time.c @@ -15,139 +15,13 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ +#include <linux/init.h> -/* - * These are routines to set up and handle interrupts from the - * sb1250 general purpose timer 0. We're using the timer as a - * system clock, so we set it up to run at 100 Hz. On every - * interrupt, we update our idea of what the time of day is, - * then call do_timer() in the architecture-independent kernel - * code to do general bookkeeping (e.g. update jiffies, run - * bottom halves, etc.) - */ -#include <linux/interrupt.h> -#include <linux/sched.h> -#include <linux/spinlock.h> -#include <linux/kernel_stat.h> - -#include <asm/irq.h> -#include <asm/addrspace.h> -#include <asm/time.h> -#include <asm/io.h> - -#include <asm/sibyte/sb1250.h> -#include <asm/sibyte/sb1250_regs.h> -#include <asm/sibyte/sb1250_int.h> -#include <asm/sibyte/sb1250_scd.h> - - -#define IMR_IP2_VAL K_INT_MAP_I0 -#define IMR_IP3_VAL K_INT_MAP_I1 -#define IMR_IP4_VAL K_INT_MAP_I2 - -#define SB1250_HPT_NUM 3 -#define SB1250_HPT_VALUE M_SCD_TIMER_CNT /* max value */ - - -extern int sb1250_steal_irq(int irq); - -static cycle_t sb1250_hpt_read(void); - -void __init sb1250_hpt_setup(void) -{ - int cpu = smp_processor_id(); - - if (!cpu) { - /* Setup hpt using timer #3 but do not enable irq for it */ - __raw_writeq(0, IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM, R_SCD_TIMER_CFG))); - __raw_writeq(SB1250_HPT_VALUE, - IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM, R_SCD_TIMER_INIT))); - __raw_writeq(M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS, - IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM, R_SCD_TIMER_CFG))); - - mips_hpt_frequency = V_SCD_TIMER_FREQ; - clocksource_mips.read = sb1250_hpt_read; - clocksource_mips.mask = M_SCD_TIMER_INIT; - } -} - - -void sb1250_time_init(void) -{ - int cpu = smp_processor_id(); - int irq = K_INT_TIMER_0+cpu; - - /* Only have 4 general purpose timers, and we use last one as hpt */ - if (cpu > 2) { - BUG(); - } - - sb1250_mask_irq(cpu, irq); - - /* Map the timer interrupt to ip[4] of this cpu */ - __raw_writeq(IMR_IP4_VAL, - IOADDR(A_IMR_REGISTER(cpu, R_IMR_INTERRUPT_MAP_BASE) + - (irq << 3))); - - /* the general purpose timer ticks at 1 Mhz independent if the rest of the system */ - /* Disable the timer and set up the count */ - __raw_writeq(0, IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG))); -#ifdef CONFIG_SIMULATION - __raw_writeq((50000 / HZ) - 1, - IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT))); -#else - __raw_writeq((V_SCD_TIMER_FREQ / HZ) - 1, - IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT))); -#endif +extern void sb1250_clocksource_init(void); +extern void sb1250_clockevent_init(void); - /* Set the timer running */ - __raw_writeq(M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS, - IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG))); - - sb1250_unmask_irq(cpu, irq); - sb1250_steal_irq(irq); - /* - * This interrupt is "special" in that it doesn't use the request_irq - * way to hook the irq line. The timer interrupt is initialized early - * enough to make this a major pain, and it's also firing enough to - * warrant a bit of special case code. sb1250_timer_interrupt is - * called directly from irq_handler.S when IP[4] is set during an - * interrupt - */ -} - -void sb1250_timer_interrupt(void) +void __init plat_time_init(void) { - int cpu = smp_processor_id(); - int irq = K_INT_TIMER_0 + cpu; - - /* ACK interrupt */ - ____raw_writeq(M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS, - IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG))); - - if (cpu == 0) { - /* - * CPU 0 handles the global timer interrupt job - */ - ll_timer_interrupt(irq); - } - else { - /* - * other CPUs should just do profiling and process accounting - */ - ll_local_timer_interrupt(irq); - } -} - -/* - * The HPT is free running from SB1250_HPT_VALUE down to 0 then starts over - * again. - */ -static cycle_t sb1250_hpt_read(void) -{ - unsigned int count; - - count = G_SCD_TIMER_CNT(__raw_readq(IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM, R_SCD_TIMER_CNT)))); - - return SB1250_HPT_VALUE - count; + sb1250_clocksource_init(); + sb1250_clockevent_init(); } diff --git a/arch/mips/sibyte/swarm/Makefile b/arch/mips/sibyte/swarm/Makefile index 2d626039195..7b45f199d92 100644 --- a/arch/mips/sibyte/swarm/Makefile +++ b/arch/mips/sibyte/swarm/Makefile @@ -1,3 +1,4 @@ -lib-y = setup.o rtc_xicor1241.o rtc_m41t81.o +obj-y := platform.o setup.o rtc_xicor1241.o \ + rtc_m41t81.o -lib-$(CONFIG_KGDB) += dbg_io.o +obj-$(CONFIG_I2C_BOARDINFO) += swarm-i2c.o diff --git a/arch/mips/sibyte/swarm/dbg_io.c b/arch/mips/sibyte/swarm/dbg_io.c deleted file mode 100644 index 75ce14c8eb6..00000000000 --- a/arch/mips/sibyte/swarm/dbg_io.c +++ /dev/null @@ -1,76 +0,0 @@ -/* - * kgdb debug routines for SiByte boards. - * - * Copyright (C) 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - */ - -/* -------------------- BEGINNING OF CONFIG --------------------- */ - -#include <linux/delay.h> -#include <asm/io.h> -#include <asm/sibyte/sb1250.h> -#include <asm/sibyte/sb1250_regs.h> -#include <asm/sibyte/sb1250_uart.h> -#include <asm/sibyte/sb1250_int.h> -#include <asm/addrspace.h> - -/* - * We use the second serial port for kgdb traffic. - * 115200, 8, N, 1. - */ - -#define BAUD_RATE 115200 -#define CLK_DIVISOR V_DUART_BAUD_RATE(BAUD_RATE) -#define DATA_BITS V_DUART_BITS_PER_CHAR_8 /* or 7 */ -#define PARITY V_DUART_PARITY_MODE_NONE /* or even */ -#define STOP_BITS M_DUART_STOP_BIT_LEN_1 /* or 2 */ - -static int duart_initialized = 0; /* 0: need to be init'ed by kgdb */ - -/* -------------------- END OF CONFIG --------------------- */ -extern int kgdb_port; - -#define duart_out(reg, val) csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port,reg))) -#define duart_in(reg) csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port,reg))) - -void putDebugChar(unsigned char c); -unsigned char getDebugChar(void); -static void -duart_init(int clk_divisor, int data, int parity, int stop) -{ - duart_out(R_DUART_MODE_REG_1, data | parity); - duart_out(R_DUART_MODE_REG_2, stop); - duart_out(R_DUART_CLK_SEL, clk_divisor); - - duart_out(R_DUART_CMD, M_DUART_RX_EN | M_DUART_TX_EN); /* enable rx and tx */ -} - -void -putDebugChar(unsigned char c) -{ - if (!duart_initialized) { - duart_initialized = 1; - duart_init(CLK_DIVISOR, DATA_BITS, PARITY, STOP_BITS); - } - while ((duart_in(R_DUART_STATUS) & M_DUART_TX_RDY) == 0); - duart_out(R_DUART_TX_HOLD, c); -} - -unsigned char -getDebugChar(void) -{ - if (!duart_initialized) { - duart_initialized = 1; - duart_init(CLK_DIVISOR, DATA_BITS, PARITY, STOP_BITS); - } - while ((duart_in(R_DUART_STATUS) & M_DUART_RX_RDY) == 0) ; - return duart_in(R_DUART_RX_HOLD); -} - diff --git a/arch/mips/sibyte/swarm/platform.c b/arch/mips/sibyte/swarm/platform.c new file mode 100644 index 00000000000..9480c14ec66 --- /dev/null +++ b/arch/mips/sibyte/swarm/platform.c @@ -0,0 +1,139 @@ +#include <linux/err.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/ata_platform.h> + +#include <asm/sibyte/board.h> +#include <asm/sibyte/sb1250_genbus.h> +#include <asm/sibyte/sb1250_regs.h> + +#if defined(CONFIG_SIBYTE_SWARM) || defined(CONFIG_SIBYTE_LITTLESUR) + +#define DRV_NAME "pata-swarm" + +#define SWARM_IDE_SHIFT 5 +#define SWARM_IDE_BASE 0x1f0 +#define SWARM_IDE_CTRL 0x3f6 + +static struct resource swarm_pata_resource[] = { + { + .name = "Swarm GenBus IDE", + .flags = IORESOURCE_MEM, + }, { + .name = "Swarm GenBus IDE", + .flags = IORESOURCE_MEM, + }, { + .name = "Swarm GenBus IDE", + .flags = IORESOURCE_IRQ, + .start = K_INT_GB_IDE, + .end = K_INT_GB_IDE, + }, +}; + +static struct pata_platform_info pata_platform_data = { + .ioport_shift = SWARM_IDE_SHIFT, +}; + +static struct platform_device swarm_pata_device = { + .name = "pata_platform", + .id = -1, + .resource = swarm_pata_resource, + .num_resources = ARRAY_SIZE(swarm_pata_resource), + .dev = { + .platform_data = &pata_platform_data, + .coherent_dma_mask = ~0, /* grumble */ + }, +}; + +static int __init swarm_pata_init(void) +{ + u8 __iomem *base; + phys_t offset, size; + struct resource *r; + + if (!SIBYTE_HAVE_IDE) + return -ENODEV; + + base = ioremap(A_IO_EXT_BASE, 0x800); + offset = __raw_readq(base + R_IO_EXT_REG(R_IO_EXT_START_ADDR, IDE_CS)); + size = __raw_readq(base + R_IO_EXT_REG(R_IO_EXT_MULT_SIZE, IDE_CS)); + iounmap(base); + + offset = G_IO_START_ADDR(offset) << S_IO_ADDRBASE; + size = (G_IO_MULT_SIZE(size) + 1) << S_IO_REGSIZE; + if (offset < A_PHYS_GENBUS || offset >= A_PHYS_GENBUS_END) { + pr_info(DRV_NAME ": PATA interface at GenBus disabled\n"); + + return -EBUSY; + } + + pr_info(DRV_NAME ": PATA interface at GenBus slot %i\n", IDE_CS); + + r = swarm_pata_resource; + r[0].start = offset + (SWARM_IDE_BASE << SWARM_IDE_SHIFT); + r[0].end = offset + ((SWARM_IDE_BASE + 8) << SWARM_IDE_SHIFT) - 1; + r[1].start = offset + (SWARM_IDE_CTRL << SWARM_IDE_SHIFT); + r[1].end = offset + ((SWARM_IDE_CTRL + 1) << SWARM_IDE_SHIFT) - 1; + + return platform_device_register(&swarm_pata_device); +} + +device_initcall(swarm_pata_init); + +#endif /* defined(CONFIG_SIBYTE_SWARM) || defined(CONFIG_SIBYTE_LITTLESUR) */ + +#define sb1250_dev_struct(num) \ + static struct resource sb1250_res##num = { \ + .name = "SB1250 MAC " __stringify(num), \ + .flags = IORESOURCE_MEM, \ + .start = A_MAC_CHANNEL_BASE(num), \ + .end = A_MAC_CHANNEL_BASE(num + 1) -1, \ + };\ + static struct platform_device sb1250_dev##num = { \ + .name = "sb1250-mac", \ + .id = num, \ + .resource = &sb1250_res##num, \ + .num_resources = 1, \ + } + +sb1250_dev_struct(0); +sb1250_dev_struct(1); +sb1250_dev_struct(2); +sb1250_dev_struct(3); + +static struct platform_device *sb1250_devs[] __initdata = { + &sb1250_dev0, + &sb1250_dev1, + &sb1250_dev2, + &sb1250_dev3, +}; + +static int __init sb1250_device_init(void) +{ + int ret; + + /* Set the number of available units based on the SOC type. */ + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1250: + case K_SYS_SOC_TYPE_BCM1250_ALT: + ret = platform_add_devices(sb1250_devs, 3); + break; + case K_SYS_SOC_TYPE_BCM1120: + case K_SYS_SOC_TYPE_BCM1125: + case K_SYS_SOC_TYPE_BCM1125H: + case K_SYS_SOC_TYPE_BCM1250_ALT2: /* Hybrid */ + ret = platform_add_devices(sb1250_devs, 2); + break; + case K_SYS_SOC_TYPE_BCM1x55: + case K_SYS_SOC_TYPE_BCM1x80: + ret = platform_add_devices(sb1250_devs, 4); + break; + default: + ret = -ENODEV; + break; + } + return ret; +} +device_initcall(sb1250_device_init); diff --git a/arch/mips/sibyte/swarm/rtc_m41t81.c b/arch/mips/sibyte/swarm/rtc_m41t81.c index c13914bdda5..b732600b47f 100644 --- a/arch/mips/sibyte/swarm/rtc_m41t81.c +++ b/arch/mips/sibyte/swarm/rtc_m41t81.c @@ -146,7 +146,8 @@ int m41t81_set_time(unsigned long t) struct rtc_time tm; unsigned long flags; - to_tm(t, &tm); + /* Note we don't care about the century */ + rtc_time_to_tm(t, &tm); /* * Note the write order matters as it ensures the correctness. @@ -155,32 +156,32 @@ int m41t81_set_time(unsigned long t) */ spin_lock_irqsave(&rtc_lock, flags); - tm.tm_sec = BIN2BCD(tm.tm_sec); + tm.tm_sec = bin2bcd(tm.tm_sec); m41t81_write(M41T81REG_SC, tm.tm_sec); - tm.tm_min = BIN2BCD(tm.tm_min); + tm.tm_min = bin2bcd(tm.tm_min); m41t81_write(M41T81REG_MN, tm.tm_min); - tm.tm_hour = BIN2BCD(tm.tm_hour); + tm.tm_hour = bin2bcd(tm.tm_hour); tm.tm_hour = (tm.tm_hour & 0x3f) | (m41t81_read(M41T81REG_HR) & 0xc0); m41t81_write(M41T81REG_HR, tm.tm_hour); /* tm_wday starts from 0 to 6 */ if (tm.tm_wday == 0) tm.tm_wday = 7; - tm.tm_wday = BIN2BCD(tm.tm_wday); + tm.tm_wday = bin2bcd(tm.tm_wday); m41t81_write(M41T81REG_DY, tm.tm_wday); - tm.tm_mday = BIN2BCD(tm.tm_mday); + tm.tm_mday = bin2bcd(tm.tm_mday); m41t81_write(M41T81REG_DT, tm.tm_mday); /* tm_mon starts from 0, *ick* */ tm.tm_mon ++; - tm.tm_mon = BIN2BCD(tm.tm_mon); + tm.tm_mon = bin2bcd(tm.tm_mon); m41t81_write(M41T81REG_MO, tm.tm_mon); /* we don't do century, everything is beyond 2000 */ tm.tm_year %= 100; - tm.tm_year = BIN2BCD(tm.tm_year); + tm.tm_year = bin2bcd(tm.tm_year); m41t81_write(M41T81REG_YR, tm.tm_year); spin_unlock_irqrestore(&rtc_lock, flags); @@ -208,12 +209,12 @@ unsigned long m41t81_get_time(void) year = m41t81_read(M41T81REG_YR); spin_unlock_irqrestore(&rtc_lock, flags); - sec = BCD2BIN(sec); - min = BCD2BIN(min); - hour = BCD2BIN(hour); - day = BCD2BIN(day); - mon = BCD2BIN(mon); - year = BCD2BIN(year); + sec = bcd2bin(sec); + min = bcd2bin(min); + hour = bcd2bin(hour); + day = bcd2bin(day); + mon = bcd2bin(mon); + year = bcd2bin(year); year += 2000; diff --git a/arch/mips/sibyte/swarm/rtc_xicor1241.c b/arch/mips/sibyte/swarm/rtc_xicor1241.c index f4a17883641..178a824b28d 100644 --- a/arch/mips/sibyte/swarm/rtc_xicor1241.c +++ b/arch/mips/sibyte/swarm/rtc_xicor1241.c @@ -4,8 +4,8 @@ * Copyright (C) 2002 MontaVista Software Inc. * Author: jsun@mvista.com or jsun@junsun.net * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ @@ -28,15 +28,15 @@ * Register bits */ -#define X1241REG_SR_BAT 0x80 /* currently on battery power */ +#define X1241REG_SR_BAT 0x80 /* currently on battery power */ #define X1241REG_SR_RWEL 0x04 /* r/w latch is enabled, can write RTC */ #define X1241REG_SR_WEL 0x02 /* r/w latch is unlocked, can enable r/w now */ #define X1241REG_SR_RTCF 0x01 /* clock failed */ #define X1241REG_BL_BP2 0x80 /* block protect 2 */ #define X1241REG_BL_BP1 0x40 /* block protect 1 */ #define X1241REG_BL_BP0 0x20 /* block protect 0 */ -#define X1241REG_BL_WD1 0x10 -#define X1241REG_BL_WD0 0x08 +#define X1241REG_BL_WD1 0x10 +#define X1241REG_BL_WD0 0x08 #define X1241REG_HR_MIL 0x80 /* military time format */ /* @@ -61,50 +61,50 @@ static int xicor_read(uint8_t addr) { - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; __raw_writeq((addr >> 8) & 0x7, SMB_CSR(R_SMB_CMD)); __raw_writeq(addr & 0xff, SMB_CSR(R_SMB_DATA)); __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR2BYTE, SMB_CSR(R_SMB_START)); - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_RD1BYTE, SMB_CSR(R_SMB_START)); - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; - if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { - /* Clear error bit by writing a 1 */ - __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); - return -1; - } + if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { + /* Clear error bit by writing a 1 */ + __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); + return -1; + } return (__raw_readq(SMB_CSR(R_SMB_DATA)) & 0xff); } static int xicor_write(uint8_t addr, int b) { - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; __raw_writeq(addr, SMB_CSR(R_SMB_CMD)); __raw_writeq((addr & 0xff) | ((b & 0xff) << 8), SMB_CSR(R_SMB_DATA)); __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR3BYTE, SMB_CSR(R_SMB_START)); - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; + while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) + ; - if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { - /* Clear error bit by writing a 1 */ - __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); - return -1; - } else { + if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { + /* Clear error bit by writing a 1 */ + __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); + return -1; + } else { return 0; } } @@ -115,7 +115,8 @@ int xicor_set_time(unsigned long t) int tmp; unsigned long flags; - to_tm(t, &tm); + rtc_time_to_tm(t, &tm); + tm.tm_year += 1900; spin_lock_irqsave(&rtc_lock, flags); /* unlock writes to the CCR */ @@ -123,18 +124,18 @@ int xicor_set_time(unsigned long t) xicor_write(X1241REG_SR, X1241REG_SR_WEL | X1241REG_SR_RWEL); /* trivial ones */ - tm.tm_sec = BIN2BCD(tm.tm_sec); + tm.tm_sec = bin2bcd(tm.tm_sec); xicor_write(X1241REG_SC, tm.tm_sec); - tm.tm_min = BIN2BCD(tm.tm_min); + tm.tm_min = bin2bcd(tm.tm_min); xicor_write(X1241REG_MN, tm.tm_min); - tm.tm_mday = BIN2BCD(tm.tm_mday); + tm.tm_mday = bin2bcd(tm.tm_mday); xicor_write(X1241REG_DT, tm.tm_mday); /* tm_mon starts from 0, *ick* */ tm.tm_mon ++; - tm.tm_mon = BIN2BCD(tm.tm_mon); + tm.tm_mon = bin2bcd(tm.tm_mon); xicor_write(X1241REG_MO, tm.tm_mon); /* year is split */ @@ -147,7 +148,7 @@ int xicor_set_time(unsigned long t) tmp = xicor_read(X1241REG_HR); if (tmp & X1241REG_HR_MIL) { /* 24 hour format */ - tm.tm_hour = BIN2BCD(tm.tm_hour); + tm.tm_hour = bin2bcd(tm.tm_hour); tmp = (tmp & ~0x3f) | (tm.tm_hour & 0x3f); } else { /* 12 hour format, with 0x2 for pm */ @@ -156,7 +157,7 @@ int xicor_set_time(unsigned long t) tmp |= 0x20; tm.tm_hour -= 12; } - tm.tm_hour = BIN2BCD(tm.tm_hour); + tm.tm_hour = bin2bcd(tm.tm_hour); tmp |= tm.tm_hour; } xicor_write(X1241REG_HR, tmp); @@ -190,13 +191,13 @@ unsigned long xicor_get_time(void) y2k = xicor_read(X1241REG_Y2K); spin_unlock_irqrestore(&rtc_lock, flags); - sec = BCD2BIN(sec); - min = BCD2BIN(min); - hour = BCD2BIN(hour); - day = BCD2BIN(day); - mon = BCD2BIN(mon); - year = BCD2BIN(year); - y2k = BCD2BIN(y2k); + sec = bcd2bin(sec); + min = bcd2bin(min); + hour = bcd2bin(hour); + day = bcd2bin(day); + mon = bcd2bin(mon); + year = bcd2bin(year); + y2k = bcd2bin(y2k); year += (y2k * 100); diff --git a/arch/mips/sibyte/swarm/setup.c b/arch/mips/sibyte/swarm/setup.c index 83572d8f3e1..3462c831d0e 100644 --- a/arch/mips/sibyte/swarm/setup.c +++ b/arch/mips/sibyte/swarm/setup.c @@ -69,39 +69,59 @@ const char *get_system_type(void) return "SiByte " SIBYTE_BOARD_NAME; } -void __init swarm_time_init(void) +int swarm_be_handler(struct pt_regs *regs, int is_fixup) { -#if defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X) - /* Setup HPT */ - sb1250_hpt_setup(); -#endif + if (!is_fixup && (regs->cp0_cause & 4)) { + /* Data bus error - print PA */ + printk("DBE physical address: %010Lx\n", + __read_64bit_c0_register($26, 1)); + } + return (is_fixup ? MIPS_BE_FIXUP : MIPS_BE_FATAL); } -void __init plat_timer_setup(struct irqaction *irq) +enum swarm_rtc_type { + RTC_NONE, + RTC_XICOR, + RTC_M41T81, +}; + +enum swarm_rtc_type swarm_rtc_type; + +void read_persistent_clock(struct timespec *ts) { - /* - * we don't set up irqaction, because we will deliver timer - * interrupts through low-level (direct) meachanism. - */ + unsigned long sec; - /* We only need to setup the generic timer */ -#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) - bcm1480_time_init(); -#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X) - sb1250_time_init(); -#else -#error invalid SiByte board configuration -#endif + switch (swarm_rtc_type) { + case RTC_XICOR: + sec = xicor_get_time(); + break; + + case RTC_M41T81: + sec = m41t81_get_time(); + break; + + case RTC_NONE: + default: + sec = mktime(2000, 1, 1, 0, 0, 0); + break; + } + ts->tv_sec = sec; + ts->tv_nsec = 0; } -int swarm_be_handler(struct pt_regs *regs, int is_fixup) +int rtc_mips_set_time(unsigned long sec) { - if (!is_fixup && (regs->cp0_cause & 4)) { - /* Data bus error - print PA */ - printk("DBE physical address: %010Lx\n", - __read_64bit_c0_register($26, 1)); + switch (swarm_rtc_type) { + case RTC_XICOR: + return xicor_set_time(sec); + + case RTC_M41T81: + return m41t81_set_time(sec); + + case RTC_NONE: + default: + return -1; } - return (is_fixup ? MIPS_BE_FIXUP : MIPS_BE_FATAL); } void __init plat_mem_setup(void) @@ -114,48 +134,23 @@ void __init plat_mem_setup(void) #error invalid SiByte board configuration #endif - panic_timeout = 5; /* For debug. */ - - board_time_init = swarm_time_init; board_be_handler = swarm_be_handler; - if (xicor_probe()) { - printk("swarm setup: Xicor 1241 RTC detected.\n"); - rtc_mips_get_time = xicor_get_time; - rtc_mips_set_time = xicor_set_time; - } - - if (m41t81_probe()) { - printk("swarm setup: M41T81 RTC detected.\n"); - rtc_mips_get_time = m41t81_get_time; - rtc_mips_set_time = m41t81_set_time; - } - - printk("This kernel optimized for " -#ifdef CONFIG_SIMULATION - "simulation" -#else - "board" -#endif - " runs " -#ifdef CONFIG_SIBYTE_CFE - "with" -#else - "without" -#endif - " CFE\n"); + if (xicor_probe()) + swarm_rtc_type = RTC_XICOR; + if (m41t81_probe()) + swarm_rtc_type = RTC_M41T81; #ifdef CONFIG_VT screen_info = (struct screen_info) { - 0, 0, /* orig-x, orig-y */ - 0, /* unused */ - 52, /* orig_video_page */ - 3, /* orig_video_mode */ - 80, /* orig_video_cols */ - 4626, 3, 9, /* unused, ega_bx, unused */ - 25, /* orig_video_lines */ - 0x22, /* orig_video_isVGA */ - 16 /* orig_video_points */ + .orig_video_page = 52, + .orig_video_mode = 3, + .orig_video_cols = 80, + .flags = 12, + .orig_video_ega_bx = 3, + .orig_video_lines = 25, + .orig_video_isVGA = 0x22, + .orig_video_points = 16, }; /* XXXKW for CFE, get lines/cols from environment */ #endif diff --git a/arch/mips/sibyte/swarm/swarm-i2c.c b/arch/mips/sibyte/swarm/swarm-i2c.c new file mode 100644 index 00000000000..062505054d4 --- /dev/null +++ b/arch/mips/sibyte/swarm/swarm-i2c.c @@ -0,0 +1,35 @@ +/* + * Broadcom BCM91250A (SWARM), etc. I2C platform setup. + * + * Copyright (c) 2008 Maciej W. Rozycki + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> + + +static struct i2c_board_info swarm_i2c_info1[] __initdata = { + { + I2C_BOARD_INFO("m41t81", 0x68), + }, +}; + +static int __init swarm_i2c_init(void) +{ + int err; + + err = i2c_register_board_info(1, swarm_i2c_info1, + ARRAY_SIZE(swarm_i2c_info1)); + if (err < 0) + printk(KERN_ERR + "swarm-i2c: cannot register board I2C devices\n"); + return err; +} + +arch_initcall(swarm_i2c_init); diff --git a/arch/mips/sibyte/swarm/time.c b/arch/mips/sibyte/swarm/time.c deleted file mode 100644 index 97c73c793c3..00000000000 --- a/arch/mips/sibyte/swarm/time.c +++ /dev/null @@ -1,244 +0,0 @@ -/* - * Copyright (C) 2000, 2001 Broadcom Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* - * Time routines for the swarm board. We pass all the hard stuff - * through to the sb1250 handling code. Only thing we really keep - * track of here is what time of day we think it is. And we don't - * really even do a good job of that... - */ - - -#include <linux/bcd.h> -#include <linux/init.h> -#include <linux/time.h> -#include <linux/sched.h> -#include <linux/spinlock.h> -#include <asm/system.h> -#include <asm/addrspace.h> -#include <asm/io.h> - -#include <asm/sibyte/sb1250.h> -#include <asm/sibyte/sb1250_regs.h> -#include <asm/sibyte/sb1250_smbus.h> - -static unsigned long long sec_bias = 0; -static unsigned int usec_bias = 0; - -/* Xicor 1241 definitions */ - -/* - * Register bits - */ - -#define X1241REG_SR_BAT 0x80 /* currently on battery power */ -#define X1241REG_SR_RWEL 0x04 /* r/w latch is enabled, can write RTC */ -#define X1241REG_SR_WEL 0x02 /* r/w latch is unlocked, can enable r/w now */ -#define X1241REG_SR_RTCF 0x01 /* clock failed */ -#define X1241REG_BL_BP2 0x80 /* block protect 2 */ -#define X1241REG_BL_BP1 0x40 /* block protect 1 */ -#define X1241REG_BL_BP0 0x20 /* block protect 0 */ -#define X1241REG_BL_WD1 0x10 -#define X1241REG_BL_WD0 0x08 -#define X1241REG_HR_MIL 0x80 /* military time format */ - -/* - * Register numbers - */ - -#define X1241REG_BL 0x10 /* block protect bits */ -#define X1241REG_INT 0x11 /* */ -#define X1241REG_SC 0x30 /* Seconds */ -#define X1241REG_MN 0x31 /* Minutes */ -#define X1241REG_HR 0x32 /* Hours */ -#define X1241REG_DT 0x33 /* Day of month */ -#define X1241REG_MO 0x34 /* Month */ -#define X1241REG_YR 0x35 /* Year */ -#define X1241REG_DW 0x36 /* Day of Week */ -#define X1241REG_Y2K 0x37 /* Year 2K */ -#define X1241REG_SR 0x3F /* Status register */ - -#define X1241_CCR_ADDRESS 0x6F - -#define SMB_CSR(reg) (IOADDR(A_SMB_REGISTER(1, reg))) - -static int xicor_read(uint8_t addr) -{ - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; - - __raw_writeq((addr >> 8) & 0x7, SMB_CSR(R_SMB_CMD)); - __raw_writeq(addr & 0xff, SMB_CSR(R_SMB_DATA)); - __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR2BYTE, - SMB_CSR(R_SMB_START)); - - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; - - __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_RD1BYTE, - SMB_CSR(R_SMB_START)); - - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; - - if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { - /* Clear error bit by writing a 1 */ - __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); - return -1; - } - - return (__raw_readq(SMB_CSR(R_SMB_DATA)) & 0xff); -} - -static int xicor_write(uint8_t addr, int b) -{ - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; - - __raw_writeq(addr, SMB_CSR(R_SMB_CMD)); - __raw_writeq((addr & 0xff) | ((b & 0xff) << 8), SMB_CSR(R_SMB_DATA)); - __raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR3BYTE, - SMB_CSR(R_SMB_START)); - - while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY) - ; - - if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) { - /* Clear error bit by writing a 1 */ - __raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS)); - return -1; - } else { - return 0; - } -} - -/* - * In order to set the CMOS clock precisely, set_rtc_mmss has to be - * called 500 ms after the second nowtime has started, because when - * nowtime is written into the registers of the CMOS clock, it will - * jump to the next second precisely 500 ms later. Check the Motorola - * MC146818A or Dallas DS12887 data sheet for details. - * - * BUG: This routine does not handle hour overflow properly; it just - * sets the minutes. Usually you'll only notice that after reboot! - */ -int set_rtc_mmss(unsigned long nowtime) -{ - int retval = 0; - int real_seconds, real_minutes, cmos_minutes; - - cmos_minutes = xicor_read(X1241REG_MN); - cmos_minutes = BCD2BIN(cmos_minutes); - - /* - * since we're only adjusting minutes and seconds, - * don't interfere with hour overflow. This avoids - * messing with unknown time zones but requires your - * RTC not to be off by more than 15 minutes - */ - real_seconds = nowtime % 60; - real_minutes = nowtime / 60; - if (((abs(real_minutes - cmos_minutes) + 15)/30) & 1) - real_minutes += 30; /* correct for half hour time zone */ - real_minutes %= 60; - - /* unlock writes to the CCR */ - xicor_write(X1241REG_SR, X1241REG_SR_WEL); - xicor_write(X1241REG_SR, X1241REG_SR_WEL | X1241REG_SR_RWEL); - - if (abs(real_minutes - cmos_minutes) < 30) { - real_seconds = BIN2BCD(real_seconds); - real_minutes = BIN2BCD(real_minutes); - xicor_write(X1241REG_SC, real_seconds); - xicor_write(X1241REG_MN, real_minutes); - } else { - printk(KERN_WARNING - "set_rtc_mmss: can't update from %d to %d\n", - cmos_minutes, real_minutes); - retval = -1; - } - - xicor_write(X1241REG_SR, 0); - - printk("set_rtc_mmss: %02d:%02d\n", real_minutes, real_seconds); - - return retval; -} - -static unsigned long __init get_swarm_time(void) -{ - unsigned int year, mon, day, hour, min, sec, y2k; - - sec = xicor_read(X1241REG_SC); - min = xicor_read(X1241REG_MN); - hour = xicor_read(X1241REG_HR); - - if (hour & X1241REG_HR_MIL) { - hour &= 0x3f; - } else { - if (hour & 0x20) - hour = (hour & 0xf) + 0x12; - } - - sec = BCD2BIN(sec); - min = BCD2BIN(min); - hour = BCD2BIN(hour); - - day = xicor_read(X1241REG_DT); - mon = xicor_read(X1241REG_MO); - year = xicor_read(X1241REG_YR); - y2k = xicor_read(X1241REG_Y2K); - - day = BCD2BIN(day); - mon = BCD2BIN(mon); - year = BCD2BIN(year); - y2k = BCD2BIN(y2k); - - year += (y2k * 100); - - return mktime(year, mon, day, hour, min, sec); -} - -/* - * Bring up the timer at 100 Hz. - */ -void __init swarm_time_init(void) -{ - unsigned int flags; - int status; - - /* Set up the scd general purpose timer 0 to cpu 0 */ - sb1250_time_init(); - - /* Establish communication with the Xicor 1241 RTC */ - /* XXXKW how do I share the SMBus with the I2C subsystem? */ - - __raw_writeq(K_SMB_FREQ_400KHZ, SMB_CSR(R_SMB_FREQ)); - __raw_writeq(0, SMB_CSR(R_SMB_CONTROL)); - - if ((status = xicor_read(X1241REG_SR_RTCF)) < 0) { - printk("x1241: couldn't detect on SWARM SMBus 1\n"); - } else { - if (status & X1241REG_SR_RTCF) - printk("x1241: battery failed -- time is probably wrong\n"); - write_seqlock_irqsave(&xtime_lock, flags); - xtime.tv_sec = get_swarm_time(); - xtime.tv_nsec = 0; - write_sequnlock_irqrestore(&xtime_lock, flags); - } -} |