diff options
Diffstat (limited to 'arch/mips/momentum')
35 files changed, 0 insertions, 4597 deletions
diff --git a/arch/mips/momentum/jaguar_atx/Makefile b/arch/mips/momentum/jaguar_atx/Makefile deleted file mode 100644 index 20bbd3ea44a..00000000000 --- a/arch/mips/momentum/jaguar_atx/Makefile +++ /dev/null @@ -1,12 +0,0 @@ -# -# Makefile for Momentum Computer's Jaguar-ATX board. -# -# Note! Dependencies are done automagically by 'make dep', which also -# removes any old dependencies. DON'T put your own dependencies here -# unless it's something special (ie not a .c file). -# - -obj-y += int-handler.o irq.o prom.o reset.o setup.o - -obj-$(CONFIG_SERIAL_8250_CONSOLE) += ja-console.o -obj-$(CONFIG_REMOTE_DEBUG) += dbg_io.o diff --git a/arch/mips/momentum/jaguar_atx/dbg_io.c b/arch/mips/momentum/jaguar_atx/dbg_io.c deleted file mode 100644 index 542eac82b63..00000000000 --- a/arch/mips/momentum/jaguar_atx/dbg_io.c +++ /dev/null @@ -1,126 +0,0 @@ -#include <linux/config.h> - -#if defined(CONFIG_REMOTE_DEBUG) - -#include <asm/serial.h> /* For the serial port location and base baud */ - -/* --- CONFIG --- */ - -typedef unsigned char uint8; -typedef unsigned int uint32; - -/* --- END OF CONFIG --- */ - -#define UART16550_BAUD_2400 2400 -#define UART16550_BAUD_4800 4800 -#define UART16550_BAUD_9600 9600 -#define UART16550_BAUD_19200 19200 -#define UART16550_BAUD_38400 38400 -#define UART16550_BAUD_57600 57600 -#define UART16550_BAUD_115200 115200 - -#define UART16550_PARITY_NONE 0 -#define UART16550_PARITY_ODD 0x08 -#define UART16550_PARITY_EVEN 0x18 -#define UART16550_PARITY_MARK 0x28 -#define UART16550_PARITY_SPACE 0x38 - -#define UART16550_DATA_5BIT 0x0 -#define UART16550_DATA_6BIT 0x1 -#define UART16550_DATA_7BIT 0x2 -#define UART16550_DATA_8BIT 0x3 - -#define UART16550_STOP_1BIT 0x0 -#define UART16550_STOP_2BIT 0x4 - -/* ----------------------------------------------------- */ - -/* === CONFIG === */ - -/* [jsun] we use the second serial port for kdb */ -#define BASE OCELOT_SERIAL1_BASE -#define MAX_BAUD OCELOT_BASE_BAUD - -/* === END OF CONFIG === */ - -#define REG_OFFSET 4 - -/* register offset */ -#define OFS_RCV_BUFFER 0 -#define OFS_TRANS_HOLD 0 -#define OFS_SEND_BUFFER 0 -#define OFS_INTR_ENABLE (1*REG_OFFSET) -#define OFS_INTR_ID (2*REG_OFFSET) -#define OFS_DATA_FORMAT (3*REG_OFFSET) -#define OFS_LINE_CONTROL (3*REG_OFFSET) -#define OFS_MODEM_CONTROL (4*REG_OFFSET) -#define OFS_RS232_OUTPUT (4*REG_OFFSET) -#define OFS_LINE_STATUS (5*REG_OFFSET) -#define OFS_MODEM_STATUS (6*REG_OFFSET) -#define OFS_RS232_INPUT (6*REG_OFFSET) -#define OFS_SCRATCH_PAD (7*REG_OFFSET) - -#define OFS_DIVISOR_LSB (0*REG_OFFSET) -#define OFS_DIVISOR_MSB (1*REG_OFFSET) - - -/* memory-mapped read/write of the port */ -#define UART16550_READ(y) (*((volatile uint8*)(BASE + y))) -#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z) - -void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) -{ - /* disable interrupts */ - UART16550_WRITE(OFS_INTR_ENABLE, 0); - - /* set up buad rate */ - { - uint32 divisor; - - /* set DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x80); - - /* set divisor */ - divisor = MAX_BAUD / baud; - UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff); - UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8); - - /* clear DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x0); - } - - /* set data format */ - UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop); -} - -static int remoteDebugInitialized = 0; - -uint8 getDebugChar(void) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0); - return UART16550_READ(OFS_RCV_BUFFER); -} - - -int putDebugChar(uint8 byte) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0); - UART16550_WRITE(OFS_SEND_BUFFER, byte); - return 1; -} - -#endif diff --git a/arch/mips/momentum/jaguar_atx/int-handler.S b/arch/mips/momentum/jaguar_atx/int-handler.S deleted file mode 100644 index 43fd5a58077..00000000000 --- a/arch/mips/momentum/jaguar_atx/int-handler.S +++ /dev/null @@ -1,128 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Based on work: - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * First-level interrupt dispatcher for Jaguar-ATX board. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <asm/asm.h> -#include <asm/mipsregs.h> -#include <asm/addrspace.h> -#include <asm/regdef.h> -#include <asm/stackframe.h> - -/* - * First level interrupt dispatcher for Ocelot-CS board - */ - .align 5 - NESTED(jaguar_handle_int, PT_SIZE, sp) - SAVE_ALL - CLI - .set at - mfc0 t0, CP0_CAUSE - mfc0 t2, CP0_STATUS - - and t0, t2 - - andi t1, t0, STATUSF_IP0 /* sw0 software interrupt */ - bnez t1, ll_sw0_irq - andi t1, t0, STATUSF_IP1 /* sw1 software interrupt */ - bnez t1, ll_sw1_irq - andi t1, t0, STATUSF_IP2 /* int0 hardware line */ - bnez t1, ll_pcixa_irq - andi t1, t0, STATUSF_IP3 /* int1 hardware line */ - bnez t1, ll_pcixb_irq - andi t1, t0, STATUSF_IP4 /* int2 hardware line */ - bnez t1, ll_pcia_irq - andi t1, t0, STATUSF_IP5 /* int3 hardware line */ - bnez t1, ll_pcib_irq - andi t1, t0, STATUSF_IP6 /* int4 hardware line */ - bnez t1, ll_uart_irq - andi t1, t0, STATUSF_IP7 /* cpu timer */ - bnez t1, ll_cputimer_irq - - nop - nop - - /* now look at extended interrupts */ - mfc0 t0, CP0_CAUSE - cfc0 t1, CP0_S1_INTCONTROL - - /* shift the mask 8 bits left to line up the bits */ - sll t2, t1, 8 - - and t0, t2 - srl t0, t0, 16 - - andi t1, t0, STATUSF_IP8 /* int6 hardware line */ - bnez t1, ll_mv64340_decode_irq - - nop - nop - - .set reorder - - /* wrong alarm or masked ... */ - j spurious_interrupt - nop - END(jaguar_handle_int) - - .align 5 -ll_sw0_irq: - li a0, 0 - move a1, sp - jal do_IRQ - j ret_from_irq -ll_sw1_irq: - li a0, 1 - move a1, sp - jal do_IRQ - j ret_from_irq -ll_pcixa_irq: - li a0, 2 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pcixb_irq: - li a0, 3 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pcia_irq: - li a0, 4 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pcib_irq: - li a0, 5 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_uart_irq: - li a0, 6 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_cputimer_irq: - li a0, 7 - move a1, sp - jal ll_timer_interrupt - j ret_from_irq - -ll_mv64340_decode_irq: - move a0, sp - jal ll_mv64340_irq - j ret_from_irq diff --git a/arch/mips/momentum/jaguar_atx/irq.c b/arch/mips/momentum/jaguar_atx/irq.c deleted file mode 100644 index 15588f91ace..00000000000 --- a/arch/mips/momentum/jaguar_atx/irq.c +++ /dev/null @@ -1,67 +0,0 @@ -/* - * Copyright (C) 2002 Momentum Computer, Inc. - * Author: Matthew Dharm, mdharm@momenco.com - * - * Based on work by: - * Copyright (C) 2000 RidgeRun, Inc. - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * - * Copyright (C) 2000, 2001 Ralf Baechle (ralf@gnu.org) - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - */ -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/signal.h> -#include <linux/types.h> -#include <asm/irq_cpu.h> -#include <asm/mipsregs.h> - -extern asmlinkage void jaguar_handle_int(void); - -static struct irqaction cascade_mv64340 = { - no_action, SA_INTERRUPT, CPU_MASK_NONE, "MV64340-Cascade", NULL, NULL -}; - -void __init arch_init_irq(void) -{ - /* - * Clear all of the interrupts while we change the able around a bit. - * int-handler is not on bootstrap - */ - clear_c0_status(ST0_IM); - - /* Sets the first-level interrupt dispatcher. */ - set_except_vector(0, jaguar_handle_int); - mips_cpu_irq_init(0); - rm7k_cpu_irq_init(8); - - /* set up the cascading interrupts */ - setup_irq(8, &cascade_mv64340); - - mv64340_irq_init(16); - - set_c0_status(ST0_IM); -} diff --git a/arch/mips/momentum/jaguar_atx/ja-console.c b/arch/mips/momentum/jaguar_atx/ja-console.c deleted file mode 100644 index da6e1ed34db..00000000000 --- a/arch/mips/momentum/jaguar_atx/ja-console.c +++ /dev/null @@ -1,106 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2001, 2002, 2004 Ralf Baechle - */ -#include <linux/init.h> -#include <linux/console.h> -#include <linux/kdev_t.h> -#include <linux/major.h> -#include <linux/termios.h> -#include <linux/sched.h> -#include <linux/tty.h> - -#include <linux/serial.h> -#include <linux/serial_core.h> -#include <asm/serial.h> - -/* SUPERIO uart register map */ -struct ja_uartregs { - union { - volatile u8 pad0[3]; - volatile u8 rbr; /* read only, DLAB == 0 */ - volatile u8 pad1[3]; - volatile u8 thr; /* write only, DLAB == 0 */ - volatile u8 pad2[3]; - volatile u8 dll; /* DLAB == 1 */ - } u1; - union { - volatile u8 pad0[3]; - volatile u8 ier; /* DLAB == 0 */ - volatile u8 pad1[3]; - volatile u8 dlm; /* DLAB == 1 */ - } u2; - union { - volatile u8 pad0[3]; - volatile u8 iir; /* read only */ - volatile u8 pad1[3]; - volatile u8 fcr; /* write only */ - } u3; - volatile u8 pad0[3]; - volatile u8 iu_lcr; - volatile u8 pad1[3]; - volatile u8 iu_mcr; - volatile u8 pad2[3]; - volatile u8 iu_lsr; - volatile u8 pad3[3]; - volatile u8 iu_msr; - volatile u8 pad4[3]; - volatile u8 iu_scr; -} ja_uregs_t; - -#define iu_rbr u1.rbr -#define iu_thr u1.thr -#define iu_dll u1.dll -#define iu_ier u2.ier -#define iu_dlm u2.dlm -#define iu_iir u3.iir -#define iu_fcr u3.fcr - -extern unsigned long uart_base; - -static inline struct ja_uartregs *console_uart(void) -{ - return (struct ja_uartregs *) (uart_base + 0x23UL); -} - -void prom_putchar(char c) -{ - struct ja_uartregs *uart = console_uart(); - - while ((uart->iu_lsr & 0x20) == 0); - uart->iu_thr = c; -} - -char __init prom_getchar(void) -{ - return 0; -} - -static void inline ja_console_probe(void) -{ - struct uart_port up; - - /* - * Register to interrupt zero because we share the interrupt with - * the serial driver which we don't properly support yet. - */ - memset(&up, 0, sizeof(up)); - up.membase = (unsigned char *) uart_base + 0x23UL; - up.irq = JAGUAR_ATX_SERIAL1_IRQ; - up.uartclk = JAGUAR_ATX_UART_CLK; - up.regshift = 2; - up.iotype = UPIO_MEM; - up.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; - up.line = 0; - - if (early_serial_setup(&up)) - printk(KERN_ERR "Early serial init of port 0 failed\n"); -} - -__init void ja_setup_console(void) -{ - ja_console_probe(); -} diff --git a/arch/mips/momentum/jaguar_atx/jaguar_atx_fpga.h b/arch/mips/momentum/jaguar_atx/jaguar_atx_fpga.h deleted file mode 100644 index 6978654c712..00000000000 --- a/arch/mips/momentum/jaguar_atx/jaguar_atx_fpga.h +++ /dev/null @@ -1,52 +0,0 @@ -/* - * Jaguar-ATX Board Register Definitions - * - * (C) 2002 Momentum Computer Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - */ -#ifndef __JAGUAR_ATX_FPGA_H__ -#define __JAGUAR_ATX_FPGA_H__ - -#define JAGUAR_ATX_REG_BOARDREV 0x0 -#define JAGUAR_ATX_REG_FPGA_REV 0x1 -#define JAGUAR_ATX_REG_FPGA_TYPE 0x2 -#define JAGUAR_ATX_REG_RESET_STATUS 0x3 -#define JAGUAR_ATX_REG_BOARD_STATUS 0x4 -#define JAGUAR_ATX_REG_RESERVED1 0x5 -#define JAGUAR_ATX_REG_SET 0x6 -#define JAGUAR_ATX_REG_CLR 0x7 -#define JAGUAR_ATX_REG_EEPROM_MODE 0x9 -#define JAGUAR_ATX_REG_RESERVED2 0xa -#define JAGUAR_ATX_REG_RESERVED3 0xb -#define JAGUAR_ATX_REG_RESERVED4 0xc -#define JAGUAR_ATX_REG_PHY_INTSTAT 0xd -#define JAGUAR_ATX_REG_RESERVED5 0xe -#define JAGUAR_ATX_REG_RESERVED6 0xf - -#define JAGUAR_ATX_CS0_ADDR 0xfc000000L - -extern unsigned long ja_fpga_base; - -#define JAGUAR_FPGA_WRITE(x,y) writeb(x, ja_fpga_base + JAGUAR_ATX_REG_##y) -#define JAGUAR_FPGA_READ(x) readb(ja_fpga_base + JAGUAR_ATX_REG_##x) - -#endif diff --git a/arch/mips/momentum/jaguar_atx/prom.c b/arch/mips/momentum/jaguar_atx/prom.c deleted file mode 100644 index fa5982ac0ac..00000000000 --- a/arch/mips/momentum/jaguar_atx/prom.c +++ /dev/null @@ -1,266 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Based on Ocelot Linux port, which is - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Added changes for SMP - Manish Lachwani (lachwani@pmc-sierra.com) - */ -#include <linux/config.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/sched.h> -#include <linux/bootmem.h> - -#include <asm/addrspace.h> -#include <asm/bootinfo.h> -#include <asm/mv64340.h> -#include <asm/pmon.h> - -#include "jaguar_atx_fpga.h" - -extern void ja_setup_console(void); - -struct callvectors *debug_vectors; - -extern unsigned long cpu_clock; - -const char *get_system_type(void) -{ - return "Momentum Jaguar-ATX"; -} - -#ifdef CONFIG_MV643XX_ETH -extern unsigned char prom_mac_addr_base[6]; - -static void burn_clocks(void) -{ - int i; - - /* this loop should burn at least 1us -- this should be plenty */ - for (i = 0; i < 0x10000; i++) - ; -} - -static u8 exchange_bit(u8 val, u8 cs) -{ - /* place the data */ - JAGUAR_FPGA_WRITE((val << 2) | cs, EEPROM_MODE); - burn_clocks(); - - /* turn the clock on */ - JAGUAR_FPGA_WRITE((val << 2) | cs | 0x2, EEPROM_MODE); - burn_clocks(); - - /* turn the clock off and read-strobe */ - JAGUAR_FPGA_WRITE((val << 2) | cs | 0x10, EEPROM_MODE); - - /* return the data */ - return ((JAGUAR_FPGA_READ(EEPROM_MODE) >> 3) & 0x1); -} - -void get_mac(char dest[6]) -{ - u8 read_opcode[12] = {1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; - int i,j; - - for (i = 0; i < 12; i++) - exchange_bit(read_opcode[i], 1); - - for (j = 0; j < 6; j++) { - dest[j] = 0; - for (i = 0; i < 8; i++) { - dest[j] <<= 1; - dest[j] |= exchange_bit(0, 1); - } - } - - /* turn off CS */ - exchange_bit(0,0); -} -#endif - -#ifdef CONFIG_MIPS64 - -unsigned long signext(unsigned long addr) -{ - addr &= 0xffffffff; - return (unsigned long)((int)addr); -} - -void *get_arg(unsigned long args, int arc) -{ - unsigned long ul; - unsigned char *puc, uc; - - args += (arc * 4); - ul = (unsigned long)signext(args); - puc = (unsigned char *)ul; - if (puc == 0) - return (void *)0; - -#ifdef CONFIG_CPU_LITTLE_ENDIAN - uc = *puc++; - l = (unsigned long)uc; - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 24); -#else - uc = *puc++; - ul = ((unsigned long)uc) << 24; - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= ((unsigned long)uc); -#endif - ul = signext(ul); - - return (void *)ul; -} - -char *arg64(unsigned long addrin, int arg_index) -{ - unsigned long args; - char *p; - - args = signext(addrin); - p = (char *)get_arg(args, arg_index); - - return p; -} -#endif /* CONFIG_MIPS64 */ - -/* PMON passes arguments in C main() style */ -void __init prom_init(void) -{ - int argc = fw_arg0; - char **arg = (char **) fw_arg1; - char **env = (char **) fw_arg2; - struct callvectors *cv = (struct callvectors *) fw_arg3; - int i; - -#ifdef CONFIG_SERIAL_8250_CONSOLE -// ja_setup_console(); /* The very first thing. */ -#endif - -#ifdef CONFIG_MIPS64 - char *ptr; - - printk("Mips64 Jaguar-ATX\n"); - /* save the PROM vectors for debugging use */ - debug_vectors = (struct callvectors *)signext((unsigned long)cv); - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - - for (i = 1; i < argc; i++) { - ptr = (char *)arg64((unsigned long)arg, i); - if ((strlen(arcs_cmdline) + strlen(ptr) + 1) >= - sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, ptr); - strcat(arcs_cmdline, " "); - } - - i = 0; - while (1) { - ptr = (char *)arg64((unsigned long)env, i); - if (! ptr) - break; - - if (strncmp("gtbase", ptr, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(ptr + strlen("gtbase="), - NULL, 16); - - if ((marvell_base & 0xffffffff00000000) == 0) - marvell_base |= 0xffffffff00000000; - - printk("marvell_base set to 0x%016lx\n", marvell_base); - } - if (strncmp("cpuclock", ptr, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(ptr + strlen("cpuclock="), - NULL, 10); - printk("cpu_clock set to %d\n", cpu_clock); - } - i++; - } - printk("arcs_cmdline: %s\n", arcs_cmdline); - -#else /* CONFIG_MIPS64 */ - /* save the PROM vectors for debugging use */ - debug_vectors = cv; - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - for (i = 1; i < argc; i++) { - if (strlen(arcs_cmdline) + strlen(arg[i] + 1) - >= sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, arg[i]); - strcat(arcs_cmdline, " "); - } - - while (*env) { - if (strncmp("gtbase", *env, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(*env + strlen("gtbase="), - NULL, 16); - } - if (strncmp("cpuclock", *env, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(*env + strlen("cpuclock="), - NULL, 10); - } - env++; - } -#endif /* CONFIG_MIPS64 */ - mips_machgroup = MACH_GROUP_MOMENCO; - mips_machtype = MACH_MOMENCO_JAGUAR_ATX; - -#ifdef CONFIG_MV643XX_ETH - /* get the base MAC address for on-board ethernet ports */ - get_mac(prom_mac_addr_base); -#endif -} - -void __init prom_free_prom_memory(void) -{ -} - -void __init prom_fixup_mem_map(unsigned long start, unsigned long end) -{ -} - -int prom_boot_secondary(int cpu, unsigned long sp, unsigned long gp) -{ - /* Clear the semaphore */ - *(volatile uint32_t *)(0xbb000a68) = 0x80000000; - - return 1; -} - -void prom_init_secondary(void) -{ - clear_c0_config(CONF_CM_CMASK); - set_c0_config(0x2); - - clear_c0_status(ST0_IM); - set_c0_status(0x1ffff); -} - -void prom_smp_finish(void) -{ -} diff --git a/arch/mips/momentum/jaguar_atx/reset.c b/arch/mips/momentum/jaguar_atx/reset.c deleted file mode 100644 index 48039484cdf..00000000000 --- a/arch/mips/momentum/jaguar_atx/reset.c +++ /dev/null @@ -1,57 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Copyright (C) 1997, 2001 Ralf Baechle - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * Copyright (C) 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - */ -#include <linux/config.h> -#include <linux/sched.h> -#include <linux/mm.h> -#include <asm/io.h> -#include <asm/pgtable.h> -#include <asm/processor.h> -#include <asm/reboot.h> -#include <asm/system.h> -#include <linux/delay.h> - -void momenco_jaguar_restart(char *command) -{ - /* base address of timekeeper portion of part */ -#ifdef CONFIG_MIPS64 - void *nvram = (void*) 0xfffffffffc807000; -#else - void *nvram = (void*) 0xfc807000; -#endif - /* Ask the NVRAM/RTC/watchdog chip to assert reset in 1/16 second */ - writeb(0x84, nvram + 0xff7); - - /* wait for the watchdog to go off */ - mdelay(100+(1000/16)); - - /* if the watchdog fails for some reason, let people know */ - printk(KERN_NOTICE "Watchdog reset failed\n"); -} - -void momenco_jaguar_halt(void) -{ - printk(KERN_NOTICE "\n** You can safely turn off the power\n"); - while (1) - __asm__(".set\tmips3\n\t" - "wait\n\t" - ".set\tmips0"); -} - -void momenco_jaguar_power_off(void) -{ - momenco_jaguar_halt(); -} diff --git a/arch/mips/momentum/jaguar_atx/setup.c b/arch/mips/momentum/jaguar_atx/setup.c deleted file mode 100644 index 30462e71506..00000000000 --- a/arch/mips/momentum/jaguar_atx/setup.c +++ /dev/null @@ -1,474 +0,0 @@ -/* - * BRIEF MODULE DESCRIPTION - * Momentum Computer Jaguar-ATX board dependent boot routines - * - * Copyright (C) 1996, 1997, 2001, 2004 Ralf Baechle (ralf@linux-mips.org) - * Copyright (C) 2000 RidgeRun, Inc. - * Copyright (C) 2001 Red Hat, Inc. - * Copyright (C) 2002 Momentum Computer - * - * Author: Matthew Dharm, Momentum Computer - * mdharm@momenco.com - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - */ -#include <linux/config.h> -#include <linux/bcd.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/mm.h> -#include <linux/bootmem.h> -#include <linux/module.h> -#include <linux/pci.h> -#include <linux/swap.h> -#include <linux/ioport.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/timex.h> -#include <linux/vmalloc.h> -#include <asm/time.h> -#include <asm/bootinfo.h> -#include <asm/page.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/processor.h> -#include <asm/ptrace.h> -#include <asm/reboot.h> -#include <asm/tlbflush.h> -#include <asm/mv64340.h> - -#include "jaguar_atx_fpga.h" - -extern unsigned long mv64340_sram_base; -unsigned long cpu_clock; - -/* These functions are used for rebooting or halting the machine*/ -extern void momenco_jaguar_restart(char *command); -extern void momenco_jaguar_halt(void); -extern void momenco_jaguar_power_off(void); - -void momenco_time_init(void); - -static char reset_reason; - -static inline unsigned long ENTRYLO(unsigned long paddr) -{ - return ((paddr & PAGE_MASK) | - (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL | - _CACHE_UNCACHED)) >> 6; -} - -void __init bus_error_init(void) { /* nothing */ } - -/* - * Load a few TLB entries for the MV64340 and perhiperals. The MV64340 is going - * to be hit on every IRQ anyway - there's absolutely no point in letting it be - * a random TLB entry, as it'll just cause needless churning of the TLB. And we - * use the other half for the serial port, which is just a PITA otherwise :) - * - * Device Physical Virtual - * MV64340 Internal Regs 0xf4000000 0xf4000000 - * Ocelot-C[S] PLD (CS0) 0xfc000000 0xfc000000 - * NVRAM (CS1) 0xfc800000 0xfc800000 - * UARTs (CS2) 0xfd000000 0xfd000000 - * Internal SRAM 0xfe000000 0xfe000000 - * M-Systems DOC (CS3) 0xff000000 0xff000000 - */ - -static __init void wire_stupidity_into_tlb(void) -{ -#ifdef CONFIG_MIPS32 - write_c0_wired(0); - local_flush_tlb_all(); - - /* marvell and extra space */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), - 0xf4000000UL, PM_64K); - /* fpga, rtc, and uart */ - add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), - 0xfc000000UL, PM_16M); -// /* m-sys and internal SRAM */ -// add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), -// 0xfe000000UL, PM_16M); - - marvell_base = 0xf4000000; - //mv64340_sram_base = 0xfe000000; /* Currently unused */ -#endif -} - -unsigned long marvell_base = 0xf4000000L; -unsigned long ja_fpga_base = JAGUAR_ATX_CS0_ADDR; -unsigned long uart_base = 0xfd000000L; -static unsigned char *rtc_base = (unsigned char*) 0xfc800000L; - -EXPORT_SYMBOL(marvell_base); - -static __init int per_cpu_mappings(void) -{ - marvell_base = (unsigned long) ioremap(0xf4000000, 0x10000); - ja_fpga_base = (unsigned long) ioremap(JAGUAR_ATX_CS0_ADDR, 0x1000); - uart_base = (unsigned long) ioremap(0xfd000000UL, 0x1000); - rtc_base = ioremap(0xfc000000UL, 0x8000); - // ioremap(0xfe000000, 32 << 20); - write_c0_wired(0); - local_flush_tlb_all(); - ja_setup_console(); - - return 0; -} -arch_initcall(per_cpu_mappings); - -unsigned long m48t37y_get_time(void) -{ - unsigned int year, month, day, hour, min, sec; - - /* stop the update */ - rtc_base[0x7ff8] = 0x40; - - year = BCD2BIN(rtc_base[0x7fff]); - year += BCD2BIN(rtc_base[0x7ff1]) * 100; - - month = BCD2BIN(rtc_base[0x7ffe]); - - day = BCD2BIN(rtc_base[0x7ffd]); - - hour = BCD2BIN(rtc_base[0x7ffb]); - min = BCD2BIN(rtc_base[0x7ffa]); - sec = BCD2BIN(rtc_base[0x7ff9]); - - /* start the update */ - rtc_base[0x7ff8] = 0x00; - - return mktime(year, month, day, hour, min, sec); -} - -int m48t37y_set_time(unsigned long sec) -{ - struct rtc_time tm; - - /* convert to a more useful format -- note months count from 0 */ - to_tm(sec, &tm); - tm.tm_mon += 1; - - /* enable writing */ - rtc_base[0x7ff8] = 0x80; - - /* year */ - rtc_base[0x7fff] = BIN2BCD(tm.tm_year % 100); - rtc_base[0x7ff1] = BIN2BCD(tm.tm_year / 100); - - /* month */ - rtc_base[0x7ffe] = BIN2BCD(tm.tm_mon); - - /* day */ - rtc_base[0x7ffd] = BIN2BCD(tm.tm_mday); - - /* hour/min/sec */ - rtc_base[0x7ffb] = BIN2BCD(tm.tm_hour); - rtc_base[0x7ffa] = BIN2BCD(tm.tm_min); - rtc_base[0x7ff9] = BIN2BCD(tm.tm_sec); - - /* day of week -- not really used, but let's keep it up-to-date */ - rtc_base[0x7ffc] = BIN2BCD(tm.tm_wday + 1); - - /* disable writing */ - rtc_base[0x7ff8] = 0x00; - - return 0; -} - -void momenco_timer_setup(struct irqaction *irq) -{ - setup_irq(8, irq); -} - -/* - * Ugly but the least of all evils. TLB initialization did flush the TLB so - * We need to setup mappings again before we can touch the RTC. - */ -void momenco_time_init(void) -{ - wire_stupidity_into_tlb(); - - mips_hpt_frequency = cpu_clock / 2; - board_timer_setup = momenco_timer_setup; - - rtc_get_time = m48t37y_get_time; - rtc_set_time = m48t37y_set_time; -} - -static struct resource mv_pci_io_mem0_resource = { - .name = "MV64340 PCI0 IO MEM", - .flags = IORESOURCE_IO -}; - -static struct resource mv_pci_mem0_resource = { - .name = "MV64340 PCI0 MEM", - .flags = IORESOURCE_MEM -}; - -static struct mv_pci_controller mv_bus0_controller = { - .pcic = { - .pci_ops = &mv_pci_ops, - .mem_resource = &mv_pci_mem0_resource, - .io_resource = &mv_pci_io_mem0_resource, - }, - .config_addr = MV64340_PCI_0_CONFIG_ADDR, - .config_vreg = MV64340_PCI_0_CONFIG_DATA_VIRTUAL_REG, -}; - -static uint32_t mv_io_base, mv_io_size; - -static void ja_pci0_init(void) -{ - uint32_t mem0_base, mem0_size; - uint32_t io_base, io_size; - - io_base = MV_READ(MV64340_PCI_0_IO_BASE_ADDR) << 16; - io_size = (MV_READ(MV64340_PCI_0_IO_SIZE) + 1) << 16; - mem0_base = MV_READ(MV64340_PCI_0_MEMORY0_BASE_ADDR) << 16; - mem0_size = (MV_READ(MV64340_PCI_0_MEMORY0_SIZE) + 1) << 16; - - mv_pci_io_mem0_resource.start = 0; - mv_pci_io_mem0_resource.end = io_size - 1; - mv_pci_mem0_resource.start = mem0_base; - mv_pci_mem0_resource.end = mem0_base + mem0_size - 1; - mv_bus0_controller.pcic.mem_offset = mem0_base; - mv_bus0_controller.pcic.io_offset = 0; - - ioport_resource.end = io_size - 1; - - register_pci_controller(&mv_bus0_controller.pcic); - - mv_io_base = io_base; - mv_io_size = io_size; -} - -static struct resource mv_pci_io_mem1_resource = { - .name = "MV64340 PCI1 IO MEM", - .flags = IORESOURCE_IO -}; - -static struct resource mv_pci_mem1_resource = { - .name = "MV64340 PCI1 MEM", - .flags = IORESOURCE_MEM -}; - -static struct mv_pci_controller mv_bus1_controller = { - .pcic = { - .pci_ops = &mv_pci_ops, - .mem_resource = &mv_pci_mem1_resource, - .io_resource = &mv_pci_io_mem1_resource, - }, - .config_addr = MV64340_PCI_1_CONFIG_ADDR, - .config_vreg = MV64340_PCI_1_CONFIG_DATA_VIRTUAL_REG, -}; - -static __init void ja_pci1_init(void) -{ - uint32_t mem0_base, mem0_size; - uint32_t io_base, io_size; - - io_base = MV_READ(MV64340_PCI_1_IO_BASE_ADDR) << 16; - io_size = (MV_READ(MV64340_PCI_1_IO_SIZE) + 1) << 16; - mem0_base = MV_READ(MV64340_PCI_1_MEMORY0_BASE_ADDR) << 16; - mem0_size = (MV_READ(MV64340_PCI_1_MEMORY0_SIZE) + 1) << 16; - - /* - * Here we assume the I/O window of second bus to be contiguous with - * the first. A gap is no problem but would waste address space for - * remapping the port space. - */ - mv_pci_io_mem1_resource.start = mv_io_size; - mv_pci_io_mem1_resource.end = mv_io_size + io_size - 1; - mv_pci_mem1_resource.start = mem0_base; - mv_pci_mem1_resource.end = mem0_base + mem0_size - 1; - mv_bus1_controller.pcic.mem_offset = mem0_base; - mv_bus1_controller.pcic.io_offset = 0; - - ioport_resource.end = io_base + io_size -mv_io_base - 1; - - register_pci_controller(&mv_bus1_controller.pcic); - - mv_io_size = io_base + io_size - mv_io_base; -} - -static __init int __init ja_pci_init(void) -{ - unsigned long io_v_base; - uint32_t enable; - - enable = ~MV_READ(MV64340_BASE_ADDR_ENABLE); - - /* - * We require at least one enabled I/O or PCI memory window or we - * will ignore this PCI bus. We ignore PCI windows 1, 2 and 3. - */ - if (enable & (0x01 << 9) || enable & (0x01 << 10)) - ja_pci0_init(); - - if (enable & (0x01 << 14) || enable & (0x01 << 15)) - ja_pci1_init(); - - if (mv_io_size) { - io_v_base = (unsigned long) ioremap(mv_io_base, mv_io_size); - if (!io_v_base) - panic("Could not ioremap I/O port range"); - - set_io_port_base(io_v_base); - } - - return 0; -} - -arch_initcall(ja_pci_init); - -static int __init momenco_jaguar_atx_setup(void) -{ - unsigned int tmpword; - - board_time_init = momenco_time_init; - - _machine_restart = momenco_jaguar_restart; - _machine_halt = momenco_jaguar_halt; - _machine_power_off = momenco_jaguar_power_off; - - /* - * initrd_start = (ulong)jaguar_initrd_start; - * initrd_end = (ulong)jaguar_initrd_start + (ulong)jaguar_initrd_size; - * initrd_below_start_ok = 1; - */ - - wire_stupidity_into_tlb(); - - /* - * shut down ethernet ports, just to be sure our memory doesn't get - * corrupted by random ethernet traffic. - */ - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1), 0xff << 8); - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(2), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(2), 0xff << 8); - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0)) & 0xff); - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1)) & 0xff); - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(2)) & 0xff); - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0)) & 0xff); - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1)) & 0xff); - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(2)) & 0xff); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0)) & ~1); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1)) & ~1); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(2), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(2)) & ~1); - - /* Turn off the Bit-Error LED */ - JAGUAR_FPGA_WRITE(0x80, CLR); - - tmpword = JAGUAR_FPGA_READ(BOARDREV); - if (tmpword < 26) - printk("Momentum Jaguar-ATX: Board Assembly Rev. %c\n", - 'A'+tmpword); - else - printk("Momentum Jaguar-ATX: Board Assembly Revision #0x%x\n", - tmpword); - - tmpword = JAGUAR_FPGA_READ(FPGA_REV); - printk("FPGA Rev: %d.%d\n", tmpword>>4, tmpword&15); - tmpword = JAGUAR_FPGA_READ(RESET_STATUS); - printk("Reset reason: 0x%x\n", tmpword); - switch (tmpword) { - case 0x1: - printk(" - Power-up reset\n"); - break; - case 0x2: - printk(" - Push-button reset\n"); - break; - case 0x8: - printk(" - Watchdog reset\n"); - break; - case 0x10: - printk(" - JTAG reset\n"); - break; - default: - printk(" - Unknown reset cause\n"); - } - reset_reason = tmpword; - JAGUAR_FPGA_WRITE(0xff, RESET_STATUS); - - tmpword = JAGUAR_FPGA_READ(BOARD_STATUS); - printk("Board Status register: 0x%02x\n", tmpword); - printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent"); - printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent"); - - /* 256MiB of RM9000x2 DDR */ -// add_memory_region(0x0, 0x100<<20, BOOT_MEM_RAM); - - /* 128MiB of MV-64340 DDR */ -// add_memory_region(0x100<<20, 0x80<<20, BOOT_MEM_RAM); - - /* XXX Memory configuration should be picked up from PMON2k */ -#ifdef CONFIG_JAGUAR_DMALOW - printk("Jaguar ATX DMA-low mode set\n"); - add_memory_region(0x00000000, 0x08000000, BOOT_MEM_RAM); - add_memory_region(0x08000000, 0x10000000, BOOT_MEM_RAM); -#else - /* 128MiB of MV-64340 DDR RAM */ - printk("Jaguar ATX DMA-low mode is not set\n"); - add_memory_region(0x100<<20, 0x80<<20, BOOT_MEM_RAM); -#endif - -#ifdef GEMDEBUG_TRACEBUFFER - { - unsigned int tbControl; - tbControl = - 0 << 26 | /* post trigger delay 0 */ - 0x2 << 16 | /* sequential trace mode */ - // 0x0 << 16 | /* non-sequential trace mode */ - // 0xf << 4 | /* watchpoints disabled */ - 2 << 2 | /* armed */ - 2 ; /* interrupt disabled */ - printk ("setting tbControl = %08lx\n", tbControl); - write_32bit_cp0_set1_register($22, tbControl); - __asm__ __volatile__(".set noreorder\n\t" \ - "nop; nop; nop; nop; nop; nop;\n\t" \ - "nop; nop; nop; nop; nop; nop;\n\t" \ - ".set reorder\n\t"); - - } -#endif - - return 0; -} - -early_initcall(momenco_jaguar_atx_setup); diff --git a/arch/mips/momentum/ocelot_3/Makefile b/arch/mips/momentum/ocelot_3/Makefile deleted file mode 100644 index aab8fd89f83..00000000000 --- a/arch/mips/momentum/ocelot_3/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for Momentum Computer's Ocelot-3 board. -# -# Note! Dependencies are done automagically by 'make dep', which also -# removes any old dependencies. DON'T put your own dependencies here -# unless it's something special (ie not a .c file). -# -obj-y += int-handler.o irq.o prom.o reset.o setup.o diff --git a/arch/mips/momentum/ocelot_3/int-handler.S b/arch/mips/momentum/ocelot_3/int-handler.S deleted file mode 100644 index 4522f09ed76..00000000000 --- a/arch/mips/momentum/ocelot_3/int-handler.S +++ /dev/null @@ -1,137 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * Copyright 2004 PMC-Sierra - * Author: Manish Lachwani (lachwani@pmc-sierra.com) - * - * Copyright (C) 2004 MontaVista Software Inc. - * Author: Manish Lachwani, mlachwani@mvista.com - * - * First-level interrupt dispatcher for Ocelot-3 board. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <asm/asm.h> -#include <asm/mipsregs.h> -#include <asm/addrspace.h> -#include <asm/regdef.h> -#include <asm/stackframe.h> - -/* - * First level interrupt dispatcher for Ocelot-3 board - */ - .align 5 - NESTED(ocelot3_handle_int, PT_SIZE, sp) - SAVE_ALL - CLI - .set at - - mfc0 t0, CP0_CAUSE - mfc0 t2, CP0_STATUS - - and t0, t2 - - andi t1, t0, STATUSF_IP0 /* sw0 software interrupt (IRQ0) */ - bnez t1, ll_sw0_irq - - andi t1, t0, STATUSF_IP1 /* sw1 software interrupt (IRQ1) */ - bnez t1, ll_sw1_irq - - andi t1, t0, STATUSF_IP2 /* int0 hardware line (IRQ2) */ - bnez t1, ll_pci0slot1_irq - - andi t1, t0, STATUSF_IP3 /* int1 hardware line (IRQ3) */ - bnez t1, ll_pci0slot2_irq - - andi t1, t0, STATUSF_IP4 /* int2 hardware line (IRQ4) */ - bnez t1, ll_pci1slot1_irq - - andi t1, t0, STATUSF_IP5 /* int3 hardware line (IRQ5) */ - bnez t1, ll_pci1slot2_irq - - andi t1, t0, STATUSF_IP6 /* int4 hardware line (IRQ6) */ - bnez t1, ll_uart_irq - - andi t1, t0, STATUSF_IP7 /* cpu timer (IRQ7) */ - bnez t1, ll_cputimer_irq - - /* now look at extended interrupts */ - mfc0 t0, CP0_CAUSE - cfc0 t1, CP0_S1_INTCONTROL - - /* shift the mask 8 bits left to line up the bits */ - sll t2, t1, 8 - - and t0, t2 - srl t0, t0, 16 - - andi t1, t0, STATUSF_IP8 /* int6 hardware line (IRQ9) */ - bnez t1, ll_mv64340_decode_irq - - .set reorder - - /* wrong alarm or masked ... */ - j spurious_interrupt - nop - END(ocelot3_handle_int) - - .align 5 -ll_sw0_irq: - li a0, 0 /* IRQ 1 */ - move a1, sp - jal do_IRQ - j ret_from_irq -ll_sw1_irq: - li a0, 1 /* IRQ 2 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pci0slot1_irq: - li a0, 2 /* IRQ 3 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pci0slot2_irq: - li a0, 3 /* IRQ 4 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pci1slot1_irq: - li a0, 4 /* IRQ 5 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pci1slot2_irq: - li a0, 5 /* IRQ 6 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_uart_irq: - li a0, 6 /* IRQ 7 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_cputimer_irq: - li a0, 7 /* IRQ 8 */ - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_mv64340_decode_irq: - move a0, sp - jal ll_mv64340_irq - j ret_from_irq - diff --git a/arch/mips/momentum/ocelot_3/irq.c b/arch/mips/momentum/ocelot_3/irq.c deleted file mode 100644 index 42464dbd4ad..00000000000 --- a/arch/mips/momentum/ocelot_3/irq.c +++ /dev/null @@ -1,81 +0,0 @@ -/* - * Copyright (C) 2000 RidgeRun, Inc. - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * Copyright (C) 2000, 2001 Ralf Baechle (ralf@gnu.org) - * - * Copyright 2004 PMC-Sierra - * Author: Manish Lachwani (lachwani@pmc-sierra.com) - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Copyright (C) 2004 MontaVista Software Inc. - * Author: Manish Lachwani, mlachwani@mvista.com - * - */ -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/kernel_stat.h> -#include <linux/module.h> -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/types.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/timex.h> -#include <linux/slab.h> -#include <linux/random.h> -#include <asm/bitops.h> -#include <asm/bootinfo.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/mipsregs.h> -#include <asm/system.h> - -extern asmlinkage void ocelot3_handle_int(void); - -static struct irqaction cascade_mv64340 = { - no_action, SA_INTERRUPT, CPU_MASK_NONE, "MV64340-Cascade", NULL, NULL -}; - -void __init arch_init_irq(void) -{ - /* - * Clear all of the interrupts while we change the able around a bit. - * int-handler is not on bootstrap - */ - clear_c0_status(ST0_IM | ST0_BEV); - - /* Sets the first-level interrupt dispatcher. */ - set_except_vector(0, ocelot3_handle_int); - mips_cpu_irq_init(0); - rm7k_cpu_irq_init(8); - - /* set up the cascading interrupts */ - setup_irq(8, &cascade_mv64340); /* unmask intControl IM8, IRQ 9 */ - mv64340_irq_init(16); - - set_c0_status(ST0_IM); /* IE in the status register */ - -} diff --git a/arch/mips/momentum/ocelot_3/ocelot_3_fpga.h b/arch/mips/momentum/ocelot_3/ocelot_3_fpga.h deleted file mode 100644 index 227e429fe72..00000000000 --- a/arch/mips/momentum/ocelot_3/ocelot_3_fpga.h +++ /dev/null @@ -1,57 +0,0 @@ -/* - * Ocelot-3 Board Register Definitions - * - * (C) 2002 Momentum Computer Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Copyright (C) 2004 MontaVista Software Inc. - * Author: Manish Lachwani, mlachwani@mvista.com - */ - -#ifndef __OCELOT_3_FPGA_H__ -#define __OCELOT_3_FPGA_H__ - -#define OCELOT_3_REG_BOARDREV 0x0 -#define OCELOT_3_REG_FPGA_REV 0x1 -#define OCELOT_3_REG_FPGA_TYPE 0x2 -#define OCELOT_3_REG_RESET_STATUS 0x3 -#define OCELOT_3_REG_BOARD_STATUS 0x4 -#define OCELOT_3_REG_CPCI_ID 0x5 -#define OCELOT_3_REG_SET 0x6 -#define OCELOT_3_REG_CLR 0x7 -#define OCELOT_3_REG_EEPROM_MODE 0x9 -#define OCELOT_3_REG_INTMASK 0xa -#define OCELOT_3_REG_INTSTAT 0xb -#define OCELOT_3_REG_UART_INTMASK 0xc -#define OCELOT_3_REG_UART_INTSTAT 0xd -#define OCELOT_3_REG_INTSET 0xe -#define OCELOT_3_REG_INTCLR 0xf - -extern unsigned long ocelot_fpga_base; - -#define OCELOT_FPGA_WRITE(x, y) writeb(x, ocelot_fpga_base + OCELOT_3_REG_##y) -#define OCELOT_FPGA_READ(x) readb(ocelot_fpga_base + OCELOT_3_REG_##x) - -#endif diff --git a/arch/mips/momentum/ocelot_3/prom.c b/arch/mips/momentum/ocelot_3/prom.c deleted file mode 100644 index 89c17a0c0be..00000000000 --- a/arch/mips/momentum/ocelot_3/prom.c +++ /dev/null @@ -1,248 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Copyright 2004 PMC-Sierra - * Author: Manish Lachwani (lachwani@pmc-sierra.com) - * - * Based on Ocelot Linux port, which is - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Copyright (C) 2004 MontaVista Software Inc. - * Author: Manish Lachwani, mlachwani@mvista.com - * - */ -#include <linux/config.h> -#include <linux/init.h> -#include <linux/bootmem.h> -#include <linux/mv643xx.h> - -#include <asm/addrspace.h> -#include <asm/bootinfo.h> -#include <asm/pmon.h> -#include "ocelot_3_fpga.h" - -struct callvectors* debug_vectors; -extern unsigned long marvell_base; -extern unsigned long cpu_clock; - -#ifdef CONFIG_MV643XX_ETH -extern unsigned char prom_mac_addr_base[6]; -#endif - -const char *get_system_type(void) -{ - return "Momentum Ocelot-3"; -} - -#ifdef CONFIG_MV643XX_ETH -void burn_clocks(void) -{ - int i; - - /* this loop should burn at least 1us -- this should be plenty */ - for (i = 0; i < 0x10000; i++) - ; -} - -u8 exchange_bit(u8 val, u8 cs) -{ - /* place the data */ - OCELOT_FPGA_WRITE((val << 2) | cs, EEPROM_MODE); - burn_clocks(); - - /* turn the clock on */ - OCELOT_FPGA_WRITE((val << 2) | cs | 0x2, EEPROM_MODE); - burn_clocks(); - - /* turn the clock off and read-strobe */ - OCELOT_FPGA_WRITE((val << 2) | cs | 0x10, EEPROM_MODE); - - /* return the data */ - return ((OCELOT_FPGA_READ(EEPROM_MODE) >> 3) & 0x1); -} - -void get_mac(char dest[6]) -{ - u8 read_opcode[12] = {1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; - int i,j; - - for (i = 0; i < 12; i++) - exchange_bit(read_opcode[i], 1); - - for (j = 0; j < 6; j++) { - dest[j] = 0; - for (i = 0; i < 8; i++) { - dest[j] <<= 1; - dest[j] |= exchange_bit(0, 1); - } - } - - /* turn off CS */ - exchange_bit(0,0); -} -#endif - - -#ifdef CONFIG_MIPS64 - -unsigned long signext(unsigned long addr) -{ - addr &= 0xffffffff; - return (unsigned long)((int)addr); -} - -void *get_arg(unsigned long args, int arc) -{ - unsigned long ul; - unsigned char *puc, uc; - - args += (arc * 4); - ul = (unsigned long)signext(args); - puc = (unsigned char *)ul; - if (puc == 0) - return (void *)0; - -#ifdef CONFIG_CPU_LITTLE_ENDIAN - uc = *puc++; - ul = (unsigned long)uc; - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 24); -#else /* CONFIG_CPU_LITTLE_ENDIAN */ - uc = *puc++; - ul = ((unsigned long)uc) << 24; - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= ((unsigned long)uc); -#endif /* CONFIG_CPU_LITTLE_ENDIAN */ - ul = signext(ul); - return (void *)ul; -} - -char *arg64(unsigned long addrin, int arg_index) -{ - unsigned long args; - char *p; - - args = signext(addrin); - p = (char *)get_arg(args, arg_index); - - return p; -} -#endif /* CONFIG_MIPS64 */ - -void __init prom_init(void) -{ - int argc = fw_arg0; - char **arg = (char **) fw_arg1; - char **env = (char **) fw_arg2; - struct callvectors *cv = (struct callvectors *) fw_arg3; - int i; - -#ifdef CONFIG_MIPS64 - char *ptr; - printk("prom_init - MIPS64\n"); - - /* save the PROM vectors for debugging use */ - debug_vectors = (struct callvectors *)signext((unsigned long)cv); - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - - for (i = 1; i < argc; i++) { - ptr = (char *)arg64((unsigned long)arg, i); - if ((strlen(arcs_cmdline) + strlen(ptr) + 1) >= - sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, ptr); - strcat(arcs_cmdline, " "); - } - i = 0; - - while (1) { - ptr = (char *)arg64((unsigned long)env, i); - if (! ptr) - break; - - if (strncmp("gtbase", ptr, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(ptr + strlen("gtbase="), - NULL, 16); - - if ((marvell_base & 0xffffffff00000000) == 0) - marvell_base |= 0xffffffff00000000; - - printk("marvell_base set to 0x%016lx\n", marvell_base); - } - if (strncmp("cpuclock", ptr, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(ptr + strlen("cpuclock="), - NULL, 10); - printk("cpu_clock set to %d\n", cpu_clock); - } - i++; - } - printk("arcs_cmdline: %s\n", arcs_cmdline); - -#else /* CONFIG_MIPS64 */ - - /* save the PROM vectors for debugging use */ - debug_vectors = cv; - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - for (i = 1; i < argc; i++) { - if (strlen(arcs_cmdline) + strlen(arg[i] + 1) - >= sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, arg[i]); - strcat(arcs_cmdline, " "); - } - - while (*env) { - if (strncmp("gtbase", *env, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(*env + strlen("gtbase="), - NULL, 16); - } - if (strncmp("cpuclock", *env, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(*env + strlen("cpuclock="), - NULL, 10); - } - env++; - } -#endif /* CONFIG_MIPS64 */ - - mips_machgroup = MACH_GROUP_MOMENCO; - mips_machtype = MACH_MOMENCO_OCELOT_3; - -#ifdef CONFIG_MV643XX_ETH - /* get the base MAC address for on-board ethernet ports */ - get_mac(prom_mac_addr_base); -#endif - -#ifndef CONFIG_MIPS64 - debug_vectors->printf("Booting Linux kernel...\n"); -#endif -} - -void __init prom_free_prom_memory(void) -{ -} - -void __init prom_fixup_mem_map(unsigned long start, unsigned long end) -{ -} diff --git a/arch/mips/momentum/ocelot_3/reset.c b/arch/mips/momentum/ocelot_3/reset.c deleted file mode 100644 index 72b4423c086..00000000000 --- a/arch/mips/momentum/ocelot_3/reset.c +++ /dev/null @@ -1,59 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Copyright (C) 1997, 01, 05 Ralf Baechle - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * Copyright (C) 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Copyright 2004 PMC-Sierra - * Author: Manish Lachwani (lachwani@pmc-sierra.com) - * - * Copyright (C) 2004 MontaVista Software Inc. - * Author: Manish Lachwani, mlachwani@mvista.com - */ -#include <linux/sched.h> -#include <linux/mm.h> -#include <linux/delay.h> -#include <asm/io.h> -#include <asm/pgtable.h> -#include <asm/processor.h> -#include <asm/reboot.h> -#include <asm/system.h> - -void momenco_ocelot_restart(char *command) -{ - /* base address of timekeeper portion of part */ - void *nvram = (void *) 0xfc807000L; - - /* Ask the NVRAM/RTC/watchdog chip to assert reset in 1/16 second */ - writeb(0x84, nvram + 0xff7); - - /* wait for the watchdog to go off */ - mdelay(100+(1000/16)); - - /* if the watchdog fails for some reason, let people know */ - printk(KERN_NOTICE "Watchdog reset failed\n"); -} - -void momenco_ocelot_halt(void) -{ - printk(KERN_NOTICE "\n** You can safely turn off the power\n"); - while (1) - __asm__(".set\tmips3\n\t" - "wait\n\t" - ".set\tmips0"); -} - -void momenco_ocelot_power_off(void) -{ - momenco_ocelot_halt(); -} diff --git a/arch/mips/momentum/ocelot_3/setup.c b/arch/mips/momentum/ocelot_3/setup.c deleted file mode 100644 index ce2efcbab7a..00000000000 --- a/arch/mips/momentum/ocelot_3/setup.c +++ /dev/null @@ -1,398 +0,0 @@ -/* - * setup.c - * - * BRIEF MODULE DESCRIPTION - * Momentum Computer Ocelot-3 board dependent boot routines - * - * Copyright (C) 1996, 1997, 01, 05 Ralf Baechle - * Copyright (C) 2000 RidgeRun, Inc. - * Copyright (C) 2001 Red Hat, Inc. - * Copyright (C) 2002 Momentum Computer - * - * Author: Matthew Dharm, Momentum Computer - * mdharm@momenco.com - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * Copyright 2004 PMC-Sierra - * Author: Manish Lachwani (lachwani@pmc-sierra.com) - * - * Copyright (C) 2004 MontaVista Software Inc. - * Author: Manish Lachwani, mlachwani@mvista.com - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - */ -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/mc146818rtc.h> -#include <linux/ioport.h> -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/timex.h> -#include <linux/bootmem.h> -#include <linux/mv643xx.h> -#include <asm/time.h> -#include <asm/page.h> -#include <asm/bootinfo.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/pci.h> -#include <asm/processor.h> -#include <asm/ptrace.h> -#include <asm/reboot.h> -#include <asm/mc146818rtc.h> -#include <asm/tlbflush.h> -#include "ocelot_3_fpga.h" - -/* Marvell Discovery Register Base */ -unsigned long marvell_base = (signed)0xf4000000; - -/* CPU clock */ -unsigned long cpu_clock; - -/* RTC/NVRAM */ -unsigned char* rtc_base = (unsigned char*)(signed)0xfc800000; - -/* FPGA Base */ -unsigned long ocelot_fpga_base = (signed)0xfc000000; - -/* Serial base */ -unsigned long uart_base = (signed)0xfd000000; - -/* - * Marvell Discovery SRAM. This is one place where Ethernet - * Tx and Rx descriptors can be placed to improve performance - */ -extern unsigned long mv64340_sram_base; - -/* These functions are used for rebooting or halting the machine*/ -extern void momenco_ocelot_restart(char *command); -extern void momenco_ocelot_halt(void); -extern void momenco_ocelot_power_off(void); - -void momenco_time_init(void); -static char reset_reason; - -void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1, - unsigned long entryhi, unsigned long pagemask); - -static inline unsigned long ENTRYLO(unsigned long paddr) -{ - return ((paddr & PAGE_MASK) | - (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL | - _CACHE_UNCACHED)) >> 6; -} - -void __init bus_error_init(void) -{ - /* nothing */ -} - -/* - * setup code for a handoff from a version 2 PMON 2000 PROM - */ -void setup_wired_tlb_entries(void) -{ - write_c0_wired(0); - local_flush_tlb_all(); - - /* marvell and extra space */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), (signed)0xf4000000, PM_64K); - - /* fpga, rtc, and uart */ - add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), (signed)0xfc000000, PM_16M); -} - -#define CONV_BCD_TO_BIN(val) (((val) & 0xf) + (((val) >> 4) * 10)) -#define CONV_BIN_TO_BCD(val) (((val) % 10) + (((val) / 10) << 4)) - -unsigned long m48t37y_get_time(void) -{ - unsigned int year, month, day, hour, min, sec; - - /* stop the update */ - rtc_base[0x7ff8] = 0x40; - - year = CONV_BCD_TO_BIN(rtc_base[0x7fff]); - year += CONV_BCD_TO_BIN(rtc_base[0x7ff1]) * 100; - - month = CONV_BCD_TO_BIN(rtc_base[0x7ffe]); - - day = CONV_BCD_TO_BIN(rtc_base[0x7ffd]); - - hour = CONV_BCD_TO_BIN(rtc_base[0x7ffb]); - min = CONV_BCD_TO_BIN(rtc_base[0x7ffa]); - sec = CONV_BCD_TO_BIN(rtc_base[0x7ff9]); - - /* start the update */ - rtc_base[0x7ff8] = 0x00; - - return mktime(year, month, day, hour, min, sec); -} - -int m48t37y_set_time(unsigned long sec) -{ - struct rtc_time tm; - - /* convert to a more useful format -- note months count from 0 */ - to_tm(sec, &tm); - tm.tm_mon += 1; - - /* enable writing */ - rtc_base[0x7ff8] = 0x80; - - /* year */ - rtc_base[0x7fff] = CONV_BIN_TO_BCD(tm.tm_year % 100); - rtc_base[0x7ff1] = CONV_BIN_TO_BCD(tm.tm_year / 100); - - /* month */ - rtc_base[0x7ffe] = CONV_BIN_TO_BCD(tm.tm_mon); - - /* day */ - rtc_base[0x7ffd] = CONV_BIN_TO_BCD(tm.tm_mday); - - /* hour/min/sec */ - rtc_base[0x7ffb] = CONV_BIN_TO_BCD(tm.tm_hour); - rtc_base[0x7ffa] = CONV_BIN_TO_BCD(tm.tm_min); - rtc_base[0x7ff9] = CONV_BIN_TO_BCD(tm.tm_sec); - - /* day of week -- not really used, but let's keep it up-to-date */ - rtc_base[0x7ffc] = CONV_BIN_TO_BCD(tm.tm_wday + 1); - - /* disable writing */ - rtc_base[0x7ff8] = 0x00; - - return 0; -} - -void momenco_timer_setup(struct irqaction *irq) -{ - setup_irq(7, irq); /* Timer interrupt, unmask status IM7 */ -} - -void momenco_time_init(void) -{ - setup_wired_tlb_entries(); - - /* - * Ocelot-3 board has been built with both - * the Rm7900 and the Rm7065C - */ - mips_hpt_frequency = cpu_clock / 2; - board_timer_setup = momenco_timer_setup; - - rtc_get_time = m48t37y_get_time; - rtc_set_time = m48t37y_set_time; -} - -/* - * PCI Support for Ocelot-3 - */ - -/* Bus #0 IO and MEM space */ -#define OCELOT_3_PCI_IO_0_START 0xe0000000 -#define OCELOT_3_PCI_IO_0_SIZE 0x08000000 -#define OCELOT_3_PCI_MEM_0_START 0xc0000000 -#define OCELOT_3_PCI_MEM_0_SIZE 0x10000000 - -/* Bus #1 IO and MEM space */ -#define OCELOT_3_PCI_IO_1_START 0xe8000000 -#define OCELOT_3_PCI_IO_1_SIZE 0x08000000 -#define OCELOT_3_PCI_MEM_1_START 0xd0000000 -#define OCELOT_3_PCI_MEM_1_SIZE 0x10000000 - -static struct resource mv_pci_io_mem0_resource = { - .name = "MV64340 PCI0 IO MEM", - .start = OCELOT_3_PCI_IO_0_START, - .end = OCELOT_3_PCI_IO_0_START + OCELOT_3_PCI_IO_0_SIZE - 1, - .flags = IORESOURCE_IO, -}; - -static struct resource mv_pci_io_mem1_resource = { - .name = "MV64340 PCI1 IO MEM", - .start = OCELOT_3_PCI_IO_1_START, - .end = OCELOT_3_PCI_IO_1_START + OCELOT_3_PCI_IO_1_SIZE - 1, - .flags = IORESOURCE_IO, -}; - -static struct resource mv_pci_mem0_resource = { - .name = "MV64340 PCI0 MEM", - .start = OCELOT_3_PCI_MEM_0_START, - .end = OCELOT_3_PCI_MEM_0_START + OCELOT_3_PCI_MEM_0_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct resource mv_pci_mem1_resource = { - .name = "MV64340 PCI1 MEM", - .start = OCELOT_3_PCI_MEM_1_START, - .end = OCELOT_3_PCI_MEM_1_START + OCELOT_3_PCI_MEM_1_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct mv_pci_controller mv_bus0_controller = { - .pcic = { - .pci_ops = &mv_pci_ops, - .mem_resource = &mv_pci_mem0_resource, - .io_resource = &mv_pci_io_mem0_resource, - }, - .config_addr = MV64340_PCI_0_CONFIG_ADDR, - .config_vreg = MV64340_PCI_0_CONFIG_DATA_VIRTUAL_REG, -}; - -static struct mv_pci_controller mv_bus1_controller = { - .pcic = { - .pci_ops = &mv_pci_ops, - .mem_resource = &mv_pci_mem1_resource, - .io_resource = &mv_pci_io_mem1_resource, - }, - .config_addr = MV64340_PCI_1_CONFIG_ADDR, - .config_vreg = MV64340_PCI_1_CONFIG_DATA_VIRTUAL_REG, -}; - -static __init int __init ja_pci_init(void) -{ - uint32_t enable; - extern int pci_probe_only; - - /* PMON will assign PCI resources */ - pci_probe_only = 1; - - enable = ~MV_READ(MV64340_BASE_ADDR_ENABLE); - /* - * We require at least one enabled I/O or PCI memory window or we - * will ignore this PCI bus. We ignore PCI windows 1, 2 and 3. - */ - if (enable & (0x01 << 9) || enable & (0x01 << 10)) - register_pci_controller(&mv_bus0_controller.pcic); - - if (enable & (0x01 << 14) || enable & (0x01 << 15)) - register_pci_controller(&mv_bus1_controller.pcic); - - ioport_resource.end = OCELOT_3_PCI_IO_0_START + OCELOT_3_PCI_IO_0_SIZE + - OCELOT_3_PCI_IO_1_SIZE - 1; - - iomem_resource.end = OCELOT_3_PCI_MEM_0_START + OCELOT_3_PCI_MEM_0_SIZE + - OCELOT_3_PCI_MEM_1_SIZE - 1; - - set_io_port_base(OCELOT_3_PCI_IO_0_START); /* mips_io_port_base */ - - return 0; -} - -arch_initcall(ja_pci_init); - -static int __init momenco_ocelot_3_setup(void) -{ - unsigned int tmpword; - - board_time_init = momenco_time_init; - - _machine_restart = momenco_ocelot_restart; - _machine_halt = momenco_ocelot_halt; - _machine_power_off = momenco_ocelot_power_off; - - /* Wired TLB entries */ - setup_wired_tlb_entries(); - - /* shut down ethernet ports, just to be sure our memory doesn't get - * corrupted by random ethernet traffic. - */ - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1), 0xff << 8); - do {} - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0)) & 0xff); - do {} - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1)) & 0xff); - do {} - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0)) & 0xff); - do {} - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1)) & 0xff); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0)) & ~1); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1)) & ~1); - - /* Turn off the Bit-Error LED */ - OCELOT_FPGA_WRITE(0x80, CLR); - - tmpword = OCELOT_FPGA_READ(BOARDREV); - if (tmpword < 26) - printk("Momenco Ocelot-3: Board Assembly Rev. %c\n", - 'A'+tmpword); - else - printk("Momenco Ocelot-3: Board Assembly Revision #0x%x\n", - tmpword); - - tmpword = OCELOT_FPGA_READ(FPGA_REV); - printk("FPGA Rev: %d.%d\n", tmpword>>4, tmpword&15); - tmpword = OCELOT_FPGA_READ(RESET_STATUS); - printk("Reset reason: 0x%x\n", tmpword); - switch (tmpword) { - case 0x1: - printk(" - Power-up reset\n"); - break; - case 0x2: - printk(" - Push-button reset\n"); - break; - case 0x4: - printk(" - cPCI bus reset\n"); - break; - case 0x8: - printk(" - Watchdog reset\n"); - break; - case 0x10: - printk(" - Software reset\n"); - break; - default: - printk(" - Unknown reset cause\n"); - } - reset_reason = tmpword; - OCELOT_FPGA_WRITE(0xff, RESET_STATUS); - - tmpword = OCELOT_FPGA_READ(CPCI_ID); - printk("cPCI ID register: 0x%02x\n", tmpword); - printk(" - Slot number: %d\n", tmpword & 0x1f); - printk(" - PCI bus present: %s\n", tmpword & 0x40 ? "yes" : "no"); - printk(" - System Slot: %s\n", tmpword & 0x20 ? "yes" : "no"); - - tmpword = OCELOT_FPGA_READ(BOARD_STATUS); - printk("Board Status register: 0x%02x\n", tmpword); - printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent"); - printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent"); - printk(" - L3 cache size: %d MB\n", (1<<((tmpword&12) >> 2))&~1); - - /* Support for 128 MB memory */ - add_memory_region(0x0, 0x08000000, BOOT_MEM_RAM); - - return 0; -} - -early_initcall(momenco_ocelot_3_setup); diff --git a/arch/mips/momentum/ocelot_c/Makefile b/arch/mips/momentum/ocelot_c/Makefile deleted file mode 100644 index 91240777f97..00000000000 --- a/arch/mips/momentum/ocelot_c/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for Momentum Computer's Ocelot-C and -CS boards. -# - -obj-y += cpci-irq.o int-handler.o irq.o prom.o reset.o \ - setup.o uart-irq.o - -obj-$(CONFIG_KGDB) += dbg_io.o diff --git a/arch/mips/momentum/ocelot_c/cpci-irq.c b/arch/mips/momentum/ocelot_c/cpci-irq.c deleted file mode 100644 index dea48b3ad68..00000000000 --- a/arch/mips/momentum/ocelot_c/cpci-irq.c +++ /dev/null @@ -1,153 +0,0 @@ -/* - * Copyright 2002 Momentum Computer - * Author: mdharm@momenco.com - * - * arch/mips/momentum/ocelot_c/cpci-irq.c - * Interrupt routines for cpci. Interrupt numbers are assigned from - * CPCI_IRQ_BASE to CPCI_IRQ_BASE+8 (8 interrupt sources). - * - * Note that the high-level software will need to be careful about using - * these interrupts. If this board is asserting a cPCI interrupt, it will - * also see the asserted interrupt. Care must be taken to avoid an - * interrupt flood. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/kernel.h> -#include <asm/ptrace.h> -#include <linux/sched.h> -#include <linux/kernel_stat.h> -#include <asm/io.h> -#include "ocelot_c_fpga.h" - -#define CPCI_IRQ_BASE 8 - -static inline int ls1bit8(unsigned int x) -{ - int b = 7, s; - - s = 4; if (((unsigned char)(x << 4)) == 0) s = 0; b -= s; x <<= s; - s = 2; if (((unsigned char)(x << 2)) == 0) s = 0; b -= s; x <<= s; - s = 1; if (((unsigned char)(x << 1)) == 0) s = 0; b -= s; - - return b; -} - -/* mask off an interrupt -- 0 is enable, 1 is disable */ -static inline void mask_cpci_irq(unsigned int irq) -{ - uint32_t value; - - value = OCELOT_FPGA_READ(INTMASK); - value |= 1 << (irq - CPCI_IRQ_BASE); - OCELOT_FPGA_WRITE(value, INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(INTMASK); -} - -/* unmask an interrupt -- 0 is enable, 1 is disable */ -static inline void unmask_cpci_irq(unsigned int irq) -{ - uint32_t value; - - value = OCELOT_FPGA_READ(INTMASK); - value &= ~(1 << (irq - CPCI_IRQ_BASE)); - OCELOT_FPGA_WRITE(value, INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(INTMASK); -} - -/* - * Enables the IRQ in the FPGA - */ -static void enable_cpci_irq(unsigned int irq) -{ - unmask_cpci_irq(irq); -} - -/* - * Initialize the IRQ in the FPGA - */ -static unsigned int startup_cpci_irq(unsigned int irq) -{ - unmask_cpci_irq(irq); - return 0; -} - -/* - * Disables the IRQ in the FPGA - */ -static void disable_cpci_irq(unsigned int irq) -{ - mask_cpci_irq(irq); -} - -/* - * Masks and ACKs an IRQ - */ -static void mask_and_ack_cpci_irq(unsigned int irq) -{ - mask_cpci_irq(irq); -} - -/* - * End IRQ processing - */ -static void end_cpci_irq(unsigned int irq) -{ - if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS))) - unmask_cpci_irq(irq); -} - -/* - * Interrupt handler for interrupts coming from the FPGA chip. - * It could be built in ethernet ports etc... - */ -void ll_cpci_irq(struct pt_regs *regs) -{ - unsigned int irq_src, irq_mask; - - /* read the interrupt status registers */ - irq_src = OCELOT_FPGA_READ(INTSTAT); - irq_mask = OCELOT_FPGA_READ(INTMASK); - - /* mask for just the interrupts we want */ - irq_src &= ~irq_mask; - - do_IRQ(ls1bit8(irq_src) + CPCI_IRQ_BASE, regs); -} - -#define shutdown_cpci_irq disable_cpci_irq - -struct hw_interrupt_type cpci_irq_type = { - "CPCI/FPGA", - startup_cpci_irq, - shutdown_cpci_irq, - enable_cpci_irq, - disable_cpci_irq, - mask_and_ack_cpci_irq, - end_cpci_irq, - NULL -}; - -void cpci_irq_init(void) -{ - int i; - - /* Reset irq handlers pointers to NULL */ - for (i = CPCI_IRQ_BASE; i < (CPCI_IRQ_BASE + 8); i++) { - irq_desc[i].status = IRQ_DISABLED; - irq_desc[i].action = 0; - irq_desc[i].depth = 2; - irq_desc[i].handler = &cpci_irq_type; - } -} diff --git a/arch/mips/momentum/ocelot_c/dbg_io.c b/arch/mips/momentum/ocelot_c/dbg_io.c deleted file mode 100644 index 8720bccfdea..00000000000 --- a/arch/mips/momentum/ocelot_c/dbg_io.c +++ /dev/null @@ -1,126 +0,0 @@ -#include <linux/config.h> - -#ifdef CONFIG_KGDB - -#include <asm/serial.h> /* For the serial port location and base baud */ - -/* --- CONFIG --- */ - -typedef unsigned char uint8; -typedef unsigned int uint32; - -/* --- END OF CONFIG --- */ - -#define UART16550_BAUD_2400 2400 -#define UART16550_BAUD_4800 4800 -#define UART16550_BAUD_9600 9600 -#define UART16550_BAUD_19200 19200 -#define UART16550_BAUD_38400 38400 -#define UART16550_BAUD_57600 57600 -#define UART16550_BAUD_115200 115200 - -#define UART16550_PARITY_NONE 0 -#define UART16550_PARITY_ODD 0x08 -#define UART16550_PARITY_EVEN 0x18 -#define UART16550_PARITY_MARK 0x28 -#define UART16550_PARITY_SPACE 0x38 - -#define UART16550_DATA_5BIT 0x0 -#define UART16550_DATA_6BIT 0x1 -#define UART16550_DATA_7BIT 0x2 -#define UART16550_DATA_8BIT 0x3 - -#define UART16550_STOP_1BIT 0x0 -#define UART16550_STOP_2BIT 0x4 - -/* ----------------------------------------------------- */ - -/* === CONFIG === */ - -/* [jsun] we use the second serial port for kdb */ -#define BASE OCELOT_SERIAL1_BASE -#define MAX_BAUD OCELOT_BASE_BAUD - -/* === END OF CONFIG === */ - -#define REG_OFFSET 4 - -/* register offset */ -#define OFS_RCV_BUFFER 0 -#define OFS_TRANS_HOLD 0 -#define OFS_SEND_BUFFER 0 -#define OFS_INTR_ENABLE (1*REG_OFFSET) -#define OFS_INTR_ID (2*REG_OFFSET) -#define OFS_DATA_FORMAT (3*REG_OFFSET) -#define OFS_LINE_CONTROL (3*REG_OFFSET) -#define OFS_MODEM_CONTROL (4*REG_OFFSET) -#define OFS_RS232_OUTPUT (4*REG_OFFSET) -#define OFS_LINE_STATUS (5*REG_OFFSET) -#define OFS_MODEM_STATUS (6*REG_OFFSET) -#define OFS_RS232_INPUT (6*REG_OFFSET) -#define OFS_SCRATCH_PAD (7*REG_OFFSET) - -#define OFS_DIVISOR_LSB (0*REG_OFFSET) -#define OFS_DIVISOR_MSB (1*REG_OFFSET) - - -/* memory-mapped read/write of the port */ -#define UART16550_READ(y) (*((volatile uint8*)(BASE + y))) -#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z) - -void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) -{ - /* disable interrupts */ - UART16550_WRITE(OFS_INTR_ENABLE, 0); - - /* set up buad rate */ - { - uint32 divisor; - - /* set DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x80); - - /* set divisor */ - divisor = MAX_BAUD / baud; - UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff); - UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8); - - /* clear DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x0); - } - - /* set data format */ - UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop); -} - -static int remoteDebugInitialized = 0; - -uint8 getDebugChar(void) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0); - return UART16550_READ(OFS_RCV_BUFFER); -} - - -int putDebugChar(uint8 byte) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0); - UART16550_WRITE(OFS_SEND_BUFFER, byte); - return 1; -} - -#endif diff --git a/arch/mips/momentum/ocelot_c/int-handler.S b/arch/mips/momentum/ocelot_c/int-handler.S deleted file mode 100644 index 2f2430648ab..00000000000 --- a/arch/mips/momentum/ocelot_c/int-handler.S +++ /dev/null @@ -1,102 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * First-level interrupt dispatcher for Ocelot-CS board. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <asm/asm.h> -#include <asm/mipsregs.h> -#include <asm/addrspace.h> -#include <asm/regdef.h> -#include <asm/stackframe.h> -#include "ocelot_c_fpga.h" - -/* - * First level interrupt dispatcher for Ocelot-CS board - */ - .align 5 - NESTED(ocelot_handle_int, PT_SIZE, sp) - SAVE_ALL - CLI - .set at - mfc0 t0, CP0_CAUSE - mfc0 t2, CP0_STATUS - - and t0, t2 - - andi t1, t0, STATUSF_IP0 /* sw0 software interrupt */ - bnez t1, ll_sw0_irq - andi t1, t0, STATUSF_IP1 /* sw1 software interrupt */ - bnez t1, ll_sw1_irq - andi t1, t0, STATUSF_IP2 /* int0 hardware line */ - bnez t1, ll_scsi_irq - andi t1, t0, STATUSF_IP3 /* int1 hardware line */ - bnez t1, ll_uart_decode_irq - andi t1, t0, STATUSF_IP4 /* int2 hardware line */ - bnez t1, ll_pmc_irq - andi t1, t0, STATUSF_IP5 /* int3 hardware line */ - bnez t1, ll_cpci_decode_irq - andi t1, t0, STATUSF_IP6 /* int4 hardware line */ - bnez t1, ll_mv64340_decode_irq - andi t1, t0, STATUSF_IP7 /* cpu timer */ - bnez t1, ll_cputimer_irq - - .set reorder - - /* wrong alarm or masked ... */ - j spurious_interrupt - nop - END(ocelot_handle_int) - - .align 5 -ll_sw0_irq: - li a0, 0 - move a1, sp - jal do_IRQ - j ret_from_irq -ll_sw1_irq: - li a0, 1 - move a1, sp - jal do_IRQ - j ret_from_irq -ll_scsi_irq: - li a0, 2 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_uart_decode_irq: - move a0, sp - jal ll_uart_irq - j ret_from_irq - -ll_pmc_irq: - li a0, 4 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_cpci_decode_irq: - move a0, sp - jal ll_cpci_irq - j ret_from_irq - -ll_mv64340_decode_irq: - move a0, sp - jal ll_mv64340_irq - j ret_from_irq - -ll_cputimer_irq: - li a0, 7 - move a1, sp - jal do_IRQ - j ret_from_irq - diff --git a/arch/mips/momentum/ocelot_c/irq.c b/arch/mips/momentum/ocelot_c/irq.c deleted file mode 100644 index 300fe8e4fbe..00000000000 --- a/arch/mips/momentum/ocelot_c/irq.c +++ /dev/null @@ -1,83 +0,0 @@ -/* - * Copyright (C) 2000 RidgeRun, Inc. - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * Copyright (C) 2000, 01, 05 Ralf Baechle (ralf@linux-mips.org) - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/kernel_stat.h> -#include <linux/module.h> -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/types.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/timex.h> -#include <linux/slab.h> -#include <linux/random.h> -#include <linux/bitops.h> -#include <asm/bootinfo.h> -#include <asm/io.h> -#include <asm/irq_cpu.h> -#include <asm/mipsregs.h> -#include <asm/mv64340.h> -#include <asm/system.h> - -extern asmlinkage void ocelot_handle_int(void); -extern void uart_irq_init(void); -extern void cpci_irq_init(void); - -static struct irqaction cascade_fpga = { - no_action, SA_INTERRUPT, CPU_MASK_NONE, "cascade via FPGA", NULL, NULL -}; - -static struct irqaction cascade_mv64340 = { - no_action, SA_INTERRUPT, CPU_MASK_NONE, "cascade via MV64340", NULL, NULL -}; - -void __init arch_init_irq(void) -{ - /* - * Clear all of the interrupts while we change the able around a bit. - * int-handler is not on bootstrap - */ - clear_c0_status(ST0_IM); - - /* Sets the first-level interrupt dispatcher. */ - set_except_vector(0, ocelot_handle_int); - mips_cpu_irq_init(0); - - /* set up the cascading interrupts */ - setup_irq(3, &cascade_fpga); - setup_irq(5, &cascade_fpga); - setup_irq(6, &cascade_mv64340); - - mv64340_irq_init(16); - uart_irq_init(); - cpci_irq_init(); -} diff --git a/arch/mips/momentum/ocelot_c/ocelot_c_fpga.h b/arch/mips/momentum/ocelot_c/ocelot_c_fpga.h deleted file mode 100644 index a6cf7a7959b..00000000000 --- a/arch/mips/momentum/ocelot_c/ocelot_c_fpga.h +++ /dev/null @@ -1,60 +0,0 @@ -/* - * Ocelot-C Board Register Definitions - * - * (C) 2002 Momentum Computer Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - */ - -#ifndef __OCELOT_C_FPGA_H__ -#define __OCELOT_C_FPGA_H__ - -#include <linux/config.h> - -#ifdef CONFIG_MIPS64 -#define OCELOT_C_CS0_ADDR (0xfffffffffc000000) -#else -#define OCELOT_C_CS0_ADDR (0xfc000000) -#endif - -#define OCELOT_C_REG_BOARDREV 0x0 -#define OCELOT_C_REG_FPGA_REV 0x1 -#define OCELOT_C_REG_FPGA_TYPE 0x2 -#define OCELOT_C_REG_RESET_STATUS 0x3 -#define OCELOT_C_REG_BOARD_STATUS 0x4 -#define OCELOT_C_REG_CPCI_ID 0x5 -#define OCELOT_C_REG_SET 0x6 -#define OCELOT_C_REG_CLR 0x7 -#define OCELOT_C_REG_EEPROM_MODE 0x9 -#define OCELOT_C_REG_INTMASK 0xa -#define OCELOT_C_REG_INTSTAT 0xb -#define OCELOT_C_REG_UART_INTMASK 0xc -#define OCELOT_C_REG_UART_INTSTAT 0xd -#define OCELOT_C_REG_INTSET 0xe -#define OCELOT_C_REG_INTCLR 0xf - -#define OCELOT_FPGA_WRITE(x, y) writeb(x, OCELOT_C_CS0_ADDR + OCELOT_C_REG_##y) -#define OCELOT_FPGA_READ(x) readb(OCELOT_C_CS0_ADDR + OCELOT_C_REG_##x) - -#endif diff --git a/arch/mips/momentum/ocelot_c/prom.c b/arch/mips/momentum/ocelot_c/prom.c deleted file mode 100644 index 49ac302d890..00000000000 --- a/arch/mips/momentum/ocelot_c/prom.c +++ /dev/null @@ -1,243 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Based on Ocelot Linux port, which is - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <linux/config.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/sched.h> -#include <linux/bootmem.h> - -#include <asm/addrspace.h> -#include <asm/bootinfo.h> -#include <asm/mv64340.h> -#include <asm/pmon.h> - -#include "ocelot_c_fpga.h" - -struct callvectors* debug_vectors; - -extern unsigned long marvell_base; -extern unsigned long cpu_clock; - -#ifdef CONFIG_MV643XX_ETH -extern unsigned char prom_mac_addr_base[6]; -#endif - -const char *get_system_type(void) -{ -#ifdef CONFIG_CPU_SR71000 - return "Momentum Ocelot-CS"; -#else - return "Momentum Ocelot-C"; -#endif -} - -#ifdef CONFIG_MV643XX_ETH -static void burn_clocks(void) -{ - int i; - - /* this loop should burn at least 1us -- this should be plenty */ - for (i = 0; i < 0x10000; i++) - ; -} - -static u8 exchange_bit(u8 val, u8 cs) -{ - /* place the data */ - OCELOT_FPGA_WRITE((val << 2) | cs, EEPROM_MODE); - burn_clocks(); - - /* turn the clock on */ - OCELOT_FPGA_WRITE((val << 2) | cs | 0x2, EEPROM_MODE); - burn_clocks(); - - /* turn the clock off and read-strobe */ - OCELOT_FPGA_WRITE((val << 2) | cs | 0x10, EEPROM_MODE); - - /* return the data */ - return ((OCELOT_FPGA_READ(EEPROM_MODE) >> 3) & 0x1); -} - -void get_mac(char dest[6]) -{ - u8 read_opcode[12] = {1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; - int i,j; - - for (i = 0; i < 12; i++) - exchange_bit(read_opcode[i], 1); - - for (j = 0; j < 6; j++) { - dest[j] = 0; - for (i = 0; i < 8; i++) { - dest[j] <<= 1; - dest[j] |= exchange_bit(0, 1); - } - } - - /* turn off CS */ - exchange_bit(0,0); -} -#endif - - -#ifdef CONFIG_MIPS64 - -unsigned long signext(unsigned long addr) -{ - addr &= 0xffffffff; - return (unsigned long)((int)addr); -} - -void *get_arg(unsigned long args, int arc) -{ - unsigned long ul; - unsigned char *puc, uc; - - args += (arc * 4); - ul = (unsigned long)signext(args); - puc = (unsigned char *)ul; - if (puc == 0) - return (void *)0; - -#ifdef CONFIG_CPU_LITTLE_ENDIAN - uc = *puc++; - ul = (unsigned long)uc; - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 24); -#else /* CONFIG_CPU_LITTLE_ENDIAN */ - uc = *puc++; - ul = ((unsigned long)uc) << 24; - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= ((unsigned long)uc); -#endif /* CONFIG_CPU_LITTLE_ENDIAN */ - ul = signext(ul); - return (void *)ul; -} - -char *arg64(unsigned long addrin, int arg_index) -{ - unsigned long args; - char *p; - args = signext(addrin); - p = (char *)get_arg(args, arg_index); - return p; -} -#endif /* CONFIG_MIPS64 */ - - -void __init prom_init(void) -{ - int argc = fw_arg0; - char **arg = (char **) fw_arg1; - char **env = (char **) fw_arg2; - struct callvectors *cv = (struct callvectors *) fw_arg3; - int i; - -#ifdef CONFIG_MIPS64 - char *ptr; - - printk("prom_init - MIPS64\n"); - /* save the PROM vectors for debugging use */ - debug_vectors = (struct callvectors *)signext((unsigned long)cv); - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - - for (i = 1; i < argc; i++) { - ptr = (char *)arg64((unsigned long)arg, i); - if ((strlen(arcs_cmdline) + strlen(ptr) + 1) >= - sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, ptr); - strcat(arcs_cmdline, " "); - } - i = 0; - while (1) { - ptr = (char *)arg64((unsigned long)env, i); - if (! ptr) - break; - - if (strncmp("gtbase", ptr, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(ptr + strlen("gtbase="), - NULL, 16); - - if ((marvell_base & 0xffffffff00000000) == 0) - marvell_base |= 0xffffffff00000000; - - printk("marvell_base set to 0x%016lx\n", marvell_base); - } - if (strncmp("cpuclock", ptr, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(ptr + strlen("cpuclock="), - NULL, 10); - printk("cpu_clock set to %d\n", cpu_clock); - } - i++; - } - printk("arcs_cmdline: %s\n", arcs_cmdline); - -#else /* CONFIG_MIPS64 */ - /* save the PROM vectors for debugging use */ - debug_vectors = cv; - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - for (i = 1; i < argc; i++) { - if (strlen(arcs_cmdline) + strlen(arg[i] + 1) - >= sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, arg[i]); - strcat(arcs_cmdline, " "); - } - - while (*env) { - if (strncmp("gtbase", *env, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(*env + strlen("gtbase="), - NULL, 16); - } - if (strncmp("cpuclock", *env, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(*env + strlen("cpuclock="), - NULL, 10); - } - env++; - } -#endif /* CONFIG_MIPS64 */ - - mips_machgroup = MACH_GROUP_MOMENCO; - mips_machtype = MACH_MOMENCO_OCELOT_C; - -#ifdef CONFIG_MV643XX_ETH - /* get the base MAC address for on-board ethernet ports */ - get_mac(prom_mac_addr_base); -#endif - -#ifndef CONFIG_MIPS64 - debug_vectors->printf("Booting Linux kernel...\n"); -#endif -} - -unsigned long __init prom_free_prom_memory(void) -{ - return 0; -} diff --git a/arch/mips/momentum/ocelot_c/reset.c b/arch/mips/momentum/ocelot_c/reset.c deleted file mode 100644 index 1f2b4263cc8..00000000000 --- a/arch/mips/momentum/ocelot_c/reset.c +++ /dev/null @@ -1,59 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Copyright (C) 1997, 2001 Ralf Baechle - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * Copyright (C) 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - */ -#include <linux/config.h> -#include <linux/sched.h> -#include <linux/mm.h> -#include <asm/io.h> -#include <asm/pgtable.h> -#include <asm/processor.h> -#include <asm/reboot.h> -#include <asm/system.h> -#include <linux/delay.h> - -void momenco_ocelot_restart(char *command) -{ - /* base address of timekeeper portion of part */ - void *nvram = (void *) -#ifdef CONFIG_MIPS64 - 0xfffffffffc807000; -#else - 0xfc807000; -#endif - - /* Ask the NVRAM/RTC/watchdog chip to assert reset in 1/16 second */ - writeb(0x84, nvram + 0xff7); - - /* wait for the watchdog to go off */ - mdelay(100+(1000/16)); - - /* if the watchdog fails for some reason, let people know */ - printk(KERN_NOTICE "Watchdog reset failed\n"); -} - -void momenco_ocelot_halt(void) -{ - printk(KERN_NOTICE "\n** You can safely turn off the power\n"); - while (1) - __asm__(".set\tmips3\n\t" - "wait\n\t" - ".set\tmips0"); -} - -void momenco_ocelot_power_off(void) -{ - momenco_ocelot_halt(); -} diff --git a/arch/mips/momentum/ocelot_c/setup.c b/arch/mips/momentum/ocelot_c/setup.c deleted file mode 100644 index 021c00e3c07..00000000000 --- a/arch/mips/momentum/ocelot_c/setup.c +++ /dev/null @@ -1,363 +0,0 @@ -/* - * BRIEF MODULE DESCRIPTION - * Momentum Computer Ocelot-C and -CS board dependent boot routines - * - * Copyright (C) 1996, 1997, 2001 Ralf Baechle - * Copyright (C) 2000 RidgeRun, Inc. - * Copyright (C) 2001 Red Hat, Inc. - * Copyright (C) 2002 Momentum Computer - * - * Author: Matthew Dharm, Momentum Computer - * mdharm@momenco.com - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -#include <linux/config.h> -#include <linux/bcd.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/mm.h> -#include <linux/swap.h> -#include <linux/ioport.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/timex.h> -#include <linux/vmalloc.h> -#include <asm/time.h> -#include <asm/bootinfo.h> -#include <asm/page.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/pci.h> -#include <asm/processor.h> -#include <asm/ptrace.h> -#include <asm/reboot.h> -#include <linux/bootmem.h> -#include <linux/blkdev.h> -#include <asm/mv64340.h> -#include "ocelot_c_fpga.h" - -unsigned long marvell_base; -extern unsigned long mv64340_sram_base; -unsigned long cpu_clock; - -/* These functions are used for rebooting or halting the machine*/ -extern void momenco_ocelot_restart(char *command); -extern void momenco_ocelot_halt(void); -extern void momenco_ocelot_power_off(void); - -void momenco_time_init(void); - -static char reset_reason; - -void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1, unsigned long entryhi, unsigned long pagemask); - -static unsigned long ENTRYLO(unsigned long paddr) -{ - return ((paddr & PAGE_MASK) | - (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL | - _CACHE_UNCACHED)) >> 6; -} - -/* setup code for a handoff from a version 2 PMON 2000 PROM */ -void PMON_v2_setup(void) -{ - /* Some wired TLB entries for the MV64340 and perhiperals. The - MV64340 is going to be hit on every IRQ anyway - there's - absolutely no point in letting it be a random TLB entry, as - it'll just cause needless churning of the TLB. And we use - the other half for the serial port, which is just a PITA - otherwise :) - - Device Physical Virtual - MV64340 Internal Regs 0xf4000000 0xf4000000 - Ocelot-C[S] PLD (CS0) 0xfc000000 0xfc000000 - NVRAM (CS1) 0xfc800000 0xfc800000 - UARTs (CS2) 0xfd000000 0xfd000000 - Internal SRAM 0xfe000000 0xfe000000 - M-Systems DOC (CS3) 0xff000000 0xff000000 - */ - printk("PMON_v2_setup\n"); - -#ifdef CONFIG_MIPS64 - /* marvell and extra space */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), 0xfffffffff4000000, PM_64K); - /* fpga, rtc, and uart */ - add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), 0xfffffffffc000000, PM_16M); - /* m-sys and internal SRAM */ - add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), 0xfffffffffe000000, PM_16M); - - marvell_base = 0xfffffffff4000000; - mv64340_sram_base = 0xfffffffffe000000; -#else - /* marvell and extra space */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), 0xf4000000, PM_64K); - /* fpga, rtc, and uart */ - add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), 0xfc000000, PM_16M); - /* m-sys and internal SRAM */ - add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), 0xfe000000, PM_16M); - - marvell_base = 0xf4000000; - mv64340_sram_base = 0xfe000000; -#endif -} - -unsigned long m48t37y_get_time(void) -{ -#ifdef CONFIG_MIPS64 - unsigned char *rtc_base = (unsigned char*)0xfffffffffc800000; -#else - unsigned char* rtc_base = (unsigned char*)0xfc800000; -#endif - unsigned int year, month, day, hour, min, sec; - - /* stop the update */ - rtc_base[0x7ff8] = 0x40; - - year = BCD2BIN(rtc_base[0x7fff]); - year += BCD2BIN(rtc_base[0x7ff1]) * 100; - - month = BCD2BIN(rtc_base[0x7ffe]); - - day = BCD2BIN(rtc_base[0x7ffd]); - - hour = BCD2BIN(rtc_base[0x7ffb]); - min = BCD2BIN(rtc_base[0x7ffa]); - sec = BCD2BIN(rtc_base[0x7ff9]); - - /* start the update */ - rtc_base[0x7ff8] = 0x00; - - return mktime(year, month, day, hour, min, sec); -} - -int m48t37y_set_time(unsigned long sec) -{ -#ifdef CONFIG_MIPS64 - unsigned char* rtc_base = (unsigned char*)0xfffffffffc800000; -#else - unsigned char* rtc_base = (unsigned char*)0xfc800000; -#endif - struct rtc_time tm; - - /* convert to a more useful format -- note months count from 0 */ - to_tm(sec, &tm); - tm.tm_mon += 1; - - /* enable writing */ - rtc_base[0x7ff8] = 0x80; - - /* year */ - rtc_base[0x7fff] = BIN2BCD(tm.tm_year % 100); - rtc_base[0x7ff1] = BIN2BCD(tm.tm_year / 100); - - /* month */ - rtc_base[0x7ffe] = BIN2BCD(tm.tm_mon); - - /* day */ - rtc_base[0x7ffd] = BIN2BCD(tm.tm_mday); - - /* hour/min/sec */ - rtc_base[0x7ffb] = BIN2BCD(tm.tm_hour); - rtc_base[0x7ffa] = BIN2BCD(tm.tm_min); - rtc_base[0x7ff9] = BIN2BCD(tm.tm_sec); - - /* day of week -- not really used, but let's keep it up-to-date */ - rtc_base[0x7ffc] = BIN2BCD(tm.tm_wday + 1); - - /* disable writing */ - rtc_base[0x7ff8] = 0x00; - - return 0; -} - -void momenco_timer_setup(struct irqaction *irq) -{ - setup_irq(7, irq); -} - -void momenco_time_init(void) -{ -#ifdef CONFIG_CPU_SR71000 - mips_hpt_frequency = cpu_clock; -#elif defined(CONFIG_CPU_RM7000) - mips_hpt_frequency = cpu_clock / 2; -#else -#error Unknown CPU for this board -#endif - printk("momenco_time_init cpu_clock=%d\n", cpu_clock); - board_timer_setup = momenco_timer_setup; - - rtc_get_time = m48t37y_get_time; - rtc_set_time = m48t37y_set_time; -} - -static void __init momenco_ocelot_c_setup(void) -{ - unsigned int tmpword; - - board_time_init = momenco_time_init; - - _machine_restart = momenco_ocelot_restart; - _machine_halt = momenco_ocelot_halt; - _machine_power_off = momenco_ocelot_power_off; - - /* - * initrd_start = (ulong)ocelot_initrd_start; - * initrd_end = (ulong)ocelot_initrd_start + (ulong)ocelot_initrd_size; - * initrd_below_start_ok = 1; - */ - - /* do handoff reconfiguration */ - PMON_v2_setup(); - - /* shut down ethernet ports, just to be sure our memory doesn't get - * corrupted by random ethernet traffic. - */ - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1), 0xff << 8); - do {} - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0)) & 0xff); - do {} - while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1)) & 0xff); - do {} - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0)) & 0xff); - do {} - while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1)) & 0xff); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0)) & ~1); - MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1), - MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1)) & ~1); - - /* Turn off the Bit-Error LED */ - OCELOT_FPGA_WRITE(0x80, CLR); - - tmpword = OCELOT_FPGA_READ(BOARDREV); -#ifdef CONFIG_CPU_SR71000 - if (tmpword < 26) - printk("Momenco Ocelot-CS: Board Assembly Rev. %c\n", - 'A'+tmpword); - else - printk("Momenco Ocelot-CS: Board Assembly Revision #0x%x\n", - tmpword); -#else - if (tmpword < 26) - printk("Momenco Ocelot-C: Board Assembly Rev. %c\n", - 'A'+tmpword); - else - printk("Momenco Ocelot-C: Board Assembly Revision #0x%x\n", - tmpword); -#endif - - tmpword = OCELOT_FPGA_READ(FPGA_REV); - printk("FPGA Rev: %d.%d\n", tmpword>>4, tmpword&15); - tmpword = OCELOT_FPGA_READ(RESET_STATUS); - printk("Reset reason: 0x%x\n", tmpword); - switch (tmpword) { - case 0x1: - printk(" - Power-up reset\n"); - break; - case 0x2: - printk(" - Push-button reset\n"); - break; - case 0x4: - printk(" - cPCI bus reset\n"); - break; - case 0x8: - printk(" - Watchdog reset\n"); - break; - case 0x10: - printk(" - Software reset\n"); - break; - default: - printk(" - Unknown reset cause\n"); - } - reset_reason = tmpword; - OCELOT_FPGA_WRITE(0xff, RESET_STATUS); - - tmpword = OCELOT_FPGA_READ(CPCI_ID); - printk("cPCI ID register: 0x%02x\n", tmpword); - printk(" - Slot number: %d\n", tmpword & 0x1f); - printk(" - PCI bus present: %s\n", tmpword & 0x40 ? "yes" : "no"); - printk(" - System Slot: %s\n", tmpword & 0x20 ? "yes" : "no"); - - tmpword = OCELOT_FPGA_READ(BOARD_STATUS); - printk("Board Status register: 0x%02x\n", tmpword); - printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent"); - printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent"); - printk(" - L3 Cache size: %d MiB\n", (1<<((tmpword&12) >> 2))&~1); - printk(" - SDRAM size: %d MiB\n", 1<<(6+(tmpword&3))); - - switch(tmpword &3) { - case 3: - /* 512MiB */ - add_memory_region(0x0, 0x200<<20, BOOT_MEM_RAM); - break; - case 2: - /* 256MiB */ - add_memory_region(0x0, 0x100<<20, BOOT_MEM_RAM); - break; - case 1: - /* 128MiB */ - add_memory_region(0x0, 0x80<<20, BOOT_MEM_RAM); - break; - case 0: - /* 1GiB -- needs CONFIG_HIGHMEM */ - add_memory_region(0x0, 0x400<<20, BOOT_MEM_RAM); - break; - } -} - -early_initcall(momenco_ocelot_c_setup); - -#ifndef CONFIG_MIPS64 -/* This needs to be one of the first initcalls, because no I/O port access - can work before this */ -static int io_base_ioremap(void) -{ - /* we're mapping PCI accesses from 0xc0000000 to 0xf0000000 */ - void *io_remap_range = ioremap(0xc0000000, 0x30000000); - - if (!io_remap_range) { - panic("Could not ioremap I/O port range"); - } - printk("io_remap_range set at 0x%08x\n", (uint32_t)io_remap_range); - set_io_port_base(io_remap_range - 0xc0000000); - - return 0; -} - -module_init(io_base_ioremap); -#endif diff --git a/arch/mips/momentum/ocelot_c/uart-irq.c b/arch/mips/momentum/ocelot_c/uart-irq.c deleted file mode 100644 index ebe1507b17d..00000000000 --- a/arch/mips/momentum/ocelot_c/uart-irq.c +++ /dev/null @@ -1,147 +0,0 @@ -/* - * Copyright 2002 Momentum Computer - * Author: mdharm@momenco.com - * - * arch/mips/momentum/ocelot_c/uart-irq.c - * Interrupt routines for UARTs. Interrupt numbers are assigned from - * 80 to 81 (2 interrupt sources). - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/kernel.h> -#include <asm/ptrace.h> -#include <linux/sched.h> -#include <linux/kernel_stat.h> -#include <asm/io.h> -#include <asm/irq.h> -#include "ocelot_c_fpga.h" - -static inline int ls1bit8(unsigned int x) -{ - int b = 7, s; - - s = 4; if (((unsigned char)(x << 4)) == 0) s = 0; b -= s; x <<= s; - s = 2; if (((unsigned char)(x << 2)) == 0) s = 0; b -= s; x <<= s; - s = 1; if (((unsigned char)(x << 1)) == 0) s = 0; b -= s; - - return b; -} - -/* mask off an interrupt -- 0 is enable, 1 is disable */ -static inline void mask_uart_irq(unsigned int irq) -{ - uint8_t value; - - value = OCELOT_FPGA_READ(UART_INTMASK); - value |= 1 << (irq - 74); - OCELOT_FPGA_WRITE(value, UART_INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(UART_INTMASK); -} - -/* unmask an interrupt -- 0 is enable, 1 is disable */ -static inline void unmask_uart_irq(unsigned int irq) -{ - uint8_t value; - - value = OCELOT_FPGA_READ(UART_INTMASK); - value &= ~(1 << (irq - 74)); - OCELOT_FPGA_WRITE(value, UART_INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(UART_INTMASK); -} - -/* - * Enables the IRQ in the FPGA - */ -static void enable_uart_irq(unsigned int irq) -{ - unmask_uart_irq(irq); -} - -/* - * Initialize the IRQ in the FPGA - */ -static unsigned int startup_uart_irq(unsigned int irq) -{ - unmask_uart_irq(irq); - return 0; -} - -/* - * Disables the IRQ in the FPGA - */ -static void disable_uart_irq(unsigned int irq) -{ - mask_uart_irq(irq); -} - -/* - * Masks and ACKs an IRQ - */ -static void mask_and_ack_uart_irq(unsigned int irq) -{ - mask_uart_irq(irq); -} - -/* - * End IRQ processing - */ -static void end_uart_irq(unsigned int irq) -{ - if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS))) - unmask_uart_irq(irq); -} - -/* - * Interrupt handler for interrupts coming from the FPGA chip. - */ -void ll_uart_irq(struct pt_regs *regs) -{ - unsigned int irq_src, irq_mask; - - /* read the interrupt status registers */ - irq_src = OCELOT_FPGA_READ(UART_INTSTAT); - irq_mask = OCELOT_FPGA_READ(UART_INTMASK); - - /* mask for just the interrupts we want */ - irq_src &= ~irq_mask; - - do_IRQ(ls1bit8(irq_src) + 74, regs); -} - -#define shutdown_uart_irq disable_uart_irq - -struct hw_interrupt_type uart_irq_type = { - "UART/FPGA", - startup_uart_irq, - shutdown_uart_irq, - enable_uart_irq, - disable_uart_irq, - mask_and_ack_uart_irq, - end_uart_irq, - NULL -}; - -void uart_irq_init(void) -{ - /* Reset irq handlers pointers to NULL */ - irq_desc[80].status = IRQ_DISABLED; - irq_desc[80].action = 0; - irq_desc[80].depth = 2; - irq_desc[80].handler = &uart_irq_type; - - irq_desc[81].status = IRQ_DISABLED; - irq_desc[81].action = 0; - irq_desc[81].depth = 2; - irq_desc[81].handler = &uart_irq_type; -} diff --git a/arch/mips/momentum/ocelot_g/Makefile b/arch/mips/momentum/ocelot_g/Makefile deleted file mode 100644 index e5f1cb08697..00000000000 --- a/arch/mips/momentum/ocelot_g/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for Momentum Computer's Ocelot-G board. -# - -obj-y += int-handler.o irq.o gt-irq.o prom.o reset.o setup.o -obj-$(CONFIG_KGDB) += dbg_io.o - -EXTRA_AFLAGS := $(CFLAGS) diff --git a/arch/mips/momentum/ocelot_g/dbg_io.c b/arch/mips/momentum/ocelot_g/dbg_io.c deleted file mode 100644 index 8720bccfdea..00000000000 --- a/arch/mips/momentum/ocelot_g/dbg_io.c +++ /dev/null @@ -1,126 +0,0 @@ -#include <linux/config.h> - -#ifdef CONFIG_KGDB - -#include <asm/serial.h> /* For the serial port location and base baud */ - -/* --- CONFIG --- */ - -typedef unsigned char uint8; -typedef unsigned int uint32; - -/* --- END OF CONFIG --- */ - -#define UART16550_BAUD_2400 2400 -#define UART16550_BAUD_4800 4800 -#define UART16550_BAUD_9600 9600 -#define UART16550_BAUD_19200 19200 -#define UART16550_BAUD_38400 38400 -#define UART16550_BAUD_57600 57600 -#define UART16550_BAUD_115200 115200 - -#define UART16550_PARITY_NONE 0 -#define UART16550_PARITY_ODD 0x08 -#define UART16550_PARITY_EVEN 0x18 -#define UART16550_PARITY_MARK 0x28 -#define UART16550_PARITY_SPACE 0x38 - -#define UART16550_DATA_5BIT 0x0 -#define UART16550_DATA_6BIT 0x1 -#define UART16550_DATA_7BIT 0x2 -#define UART16550_DATA_8BIT 0x3 - -#define UART16550_STOP_1BIT 0x0 -#define UART16550_STOP_2BIT 0x4 - -/* ----------------------------------------------------- */ - -/* === CONFIG === */ - -/* [jsun] we use the second serial port for kdb */ -#define BASE OCELOT_SERIAL1_BASE -#define MAX_BAUD OCELOT_BASE_BAUD - -/* === END OF CONFIG === */ - -#define REG_OFFSET 4 - -/* register offset */ -#define OFS_RCV_BUFFER 0 -#define OFS_TRANS_HOLD 0 -#define OFS_SEND_BUFFER 0 -#define OFS_INTR_ENABLE (1*REG_OFFSET) -#define OFS_INTR_ID (2*REG_OFFSET) -#define OFS_DATA_FORMAT (3*REG_OFFSET) -#define OFS_LINE_CONTROL (3*REG_OFFSET) -#define OFS_MODEM_CONTROL (4*REG_OFFSET) -#define OFS_RS232_OUTPUT (4*REG_OFFSET) -#define OFS_LINE_STATUS (5*REG_OFFSET) -#define OFS_MODEM_STATUS (6*REG_OFFSET) -#define OFS_RS232_INPUT (6*REG_OFFSET) -#define OFS_SCRATCH_PAD (7*REG_OFFSET) - -#define OFS_DIVISOR_LSB (0*REG_OFFSET) -#define OFS_DIVISOR_MSB (1*REG_OFFSET) - - -/* memory-mapped read/write of the port */ -#define UART16550_READ(y) (*((volatile uint8*)(BASE + y))) -#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z) - -void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) -{ - /* disable interrupts */ - UART16550_WRITE(OFS_INTR_ENABLE, 0); - - /* set up buad rate */ - { - uint32 divisor; - - /* set DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x80); - - /* set divisor */ - divisor = MAX_BAUD / baud; - UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff); - UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8); - - /* clear DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x0); - } - - /* set data format */ - UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop); -} - -static int remoteDebugInitialized = 0; - -uint8 getDebugChar(void) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0); - return UART16550_READ(OFS_RCV_BUFFER); -} - - -int putDebugChar(uint8 byte) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0); - UART16550_WRITE(OFS_SEND_BUFFER, byte); - return 1; -} - -#endif diff --git a/arch/mips/momentum/ocelot_g/gt-irq.c b/arch/mips/momentum/ocelot_g/gt-irq.c deleted file mode 100644 index d0b5c9dd0ea..00000000000 --- a/arch/mips/momentum/ocelot_g/gt-irq.c +++ /dev/null @@ -1,214 +0,0 @@ -/* - * - * Copyright 2002 Momentum Computer - * Author: mdharm@momenco.com - * - * arch/mips/momentum/ocelot_g/gt_irq.c - * Interrupt routines for gt64240. Currently it only handles timer irq. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <linux/config.h> -#include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/kernel.h> -#include <asm/ptrace.h> -#include <linux/sched.h> -#include <linux/kernel_stat.h> -#include <asm/gt64240.h> -#include <asm/io.h> - -unsigned long bus_clock; - -/* - * These are interrupt handlers for the GT on-chip interrupts. They - * all come in to the MIPS on a single interrupt line, and have to - * be handled and ack'ed differently than other MIPS interrupts. - */ - -#if CURRENTLY_UNUSED - -struct tq_struct irq_handlers[MAX_CAUSE_REGS][MAX_CAUSE_REG_WIDTH]; -void hook_irq_handler(int int_cause, int bit_num, void *isr_ptr); - -/* - * Hooks IRQ handler to the system. When the system is interrupted - * the interrupt service routine is called. - * - * Inputs : - * int_cause - The interrupt cause number. In EVB64120 two parameters - * are declared, INT_CAUSE_MAIN and INT_CAUSE_HIGH. - * bit_num - Indicates which bit number in the cause register - * isr_ptr - Pointer to the interrupt service routine - */ -void hook_irq_handler(int int_cause, int bit_num, void *isr_ptr) -{ - irq_handlers[int_cause][bit_num].routine = isr_ptr; -} - - -/* - * Enables the IRQ on Galileo Chip - * - * Inputs : - * int_cause - The interrupt cause number. In EVB64120 two parameters - * are declared, INT_CAUSE_MAIN and INT_CAUSE_HIGH. - * bit_num - Indicates which bit number in the cause register - * - * Outputs : - * 1 if succesful, 0 if failure - */ -int enable_galileo_irq(int int_cause, int bit_num) -{ - if (int_cause == INT_CAUSE_MAIN) - SET_REG_BITS(CPU_INTERRUPT_MASK_REGISTER, (1 << bit_num)); - else if (int_cause == INT_CAUSE_HIGH) - SET_REG_BITS(CPU_HIGH_INTERRUPT_MASK_REGISTER, - (1 << bit_num)); - else - return 0; - - return 1; -} - -/* - * Disables the IRQ on Galileo Chip - * - * Inputs : - * int_cause - The interrupt cause number. In EVB64120 two parameters - * are declared, INT_CAUSE_MAIN and INT_CAUSE_HIGH. - * bit_num - Indicates which bit number in the cause register - * - * Outputs : - * 1 if succesful, 0 if failure - */ -int disable_galileo_irq(int int_cause, int bit_num) -{ - if (int_cause == INT_CAUSE_MAIN) - RESET_REG_BITS(CPU_INTERRUPT_MASK_REGISTER, - (1 << bit_num)); - else if (int_cause == INT_CAUSE_HIGH) - RESET_REG_BITS(CPU_HIGH_INTERRUPT_MASK_REGISTER, - (1 << bit_num)); - else - return 0; - return 1; -} -#endif /* UNUSED */ - -/* - * Interrupt handler for interrupts coming from the Galileo chip via P0_INT#. - * - * We route the timer interrupt to P0_INT# (IRQ 6), and that's all this - * routine can handle, for now. - * - * In the future, we'll route more interrupts to this pin, and that's why - * we keep this particular structure in the function. - */ - -static irqreturn_t gt64240_p0int_irq(int irq, void *dev, struct pt_regs *regs) -{ - uint32_t irq_src, irq_src_mask; - int handled; - - /* get the low interrupt cause register */ - irq_src = MV_READ(LOW_INTERRUPT_CAUSE_REGISTER); - - /* get the mask register for this pin */ - irq_src_mask = MV_READ(PCI_0INTERRUPT_CAUSE_MASK_REGISTER_LOW); - - /* mask off only the interrupts we're interested in */ - irq_src = irq_src & irq_src_mask; - - handled = IRQ_NONE; - - /* Check for timer interrupt */ - if (irq_src & 0x00000100) { - handled = IRQ_HANDLED; - irq_src &= ~0x00000100; - - /* Clear any pending cause bits */ - MV_WRITE(TIMER_COUNTER_0_3_INTERRUPT_CAUSE, 0x0); - - /* handle the timer call */ - do_timer(regs); -#ifndef CONFIG_SMP - update_process_times(user_mode(regs)); -#endif - } - - if (irq_src) { - printk(KERN_INFO - "UNKNOWN P0_INT# interrupt received, irq_src=0x%x\n", - irq_src); - } - - return handled; -} - -/* - * Initializes timer using galileo's built in timer. - */ - -/* - * This will ignore the standard MIPS timer interrupt handler - * that is passed in as *irq (=irq0 in ../kernel/time.c). - * We will do our own timer interrupt handling. - */ -void gt64240_time_init(void) -{ - static struct irqaction timer; - - /* Stop the timer -- we'll use timer #0 */ - MV_WRITE(TIMER_COUNTER_0_3_CONTROL, 0x0); - - /* Load timer value for 100 Hz */ - MV_WRITE(TIMER_COUNTER0, bus_clock / 100); - - /* - * Create the IRQ structure entry for the timer. Since we're too early - * in the boot process to use the "request_irq()" call, we'll hard-code - * the values to the correct interrupt line. - */ - timer.handler = >64240_p0int_irq; - timer.flags = SA_SHIRQ | SA_INTERRUPT; - timer.name = "timer"; - timer.dev_id = NULL; - timer.next = NULL; - timer.mask = 0; - irq_desc[6].action = &timer; - - enable_irq(6); - - /* Clear any pending cause bits */ - MV_WRITE(TIMER_COUNTER_0_3_INTERRUPT_CAUSE, 0x0); - - /* Enable the interrupt for timer 0 */ - MV_WRITE(TIMER_COUNTER_0_3_INTERRUPT_MASK, 0x1); - - /* Enable the timer interrupt for GT-64240 pin P0_INT# */ - MV_WRITE (PCI_0INTERRUPT_CAUSE_MASK_REGISTER_LOW, 0x100); - - /* Configure and start the timer */ - MV_WRITE(TIMER_COUNTER_0_3_CONTROL, 0x3); -} - -void gt64240_irq_init(void) -{ -#if CURRENTLY_UNUSED - int i, j; - - /* Reset irq handlers pointers to NULL */ - for (i = 0; i < MAX_CAUSE_REGS; i++) { - for (j = 0; j < MAX_CAUSE_REG_WIDTH; j++) { - irq_handlers[i][j].next = NULL; - irq_handlers[i][j].sync = 0; - irq_handlers[i][j].routine = NULL; - irq_handlers[i][j].data = NULL; - } - } -#endif -} diff --git a/arch/mips/momentum/ocelot_g/int-handler.S b/arch/mips/momentum/ocelot_g/int-handler.S deleted file mode 100644 index 772e8f71317..00000000000 --- a/arch/mips/momentum/ocelot_g/int-handler.S +++ /dev/null @@ -1,131 +0,0 @@ -/* - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * First-level interrupt dispatcher for ocelot board. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <asm/asm.h> -#include <asm/mipsregs.h> -#include <asm/addrspace.h> -#include <asm/regdef.h> -#include <asm/stackframe.h> - -/* - * first level interrupt dispatcher for ocelot board - - * We check for the timer first, then check PCI ints A and D. - * Then check for serial IRQ and fall through. - */ - .align 5 - NESTED(ocelot_handle_int, PT_SIZE, sp) - SAVE_ALL - CLI - .set at - mfc0 t0, CP0_CAUSE - mfc0 t2, CP0_STATUS - - and t0, t2 - - andi t1, t0, STATUSF_IP2 /* int0 hardware line */ - bnez t1, ll_pri_enet_irq - andi t1, t0, STATUSF_IP3 /* int1 hardware line */ - bnez t1, ll_sec_enet_irq - andi t1, t0, STATUSF_IP4 /* int2 hardware line */ - bnez t1, ll_uart_irq - andi t1, t0, STATUSF_IP5 /* int3 hardware line */ - bnez t1, ll_cpci_irq - andi t1, t0, STATUSF_IP6 /* int4 hardware line */ - bnez t1, ll_galileo_p0_irq - andi t1, t0, STATUSF_IP7 /* cpu timer */ - bnez t1, ll_cputimer_irq - - /* now look at the extended interrupts */ - mfc0 t0, CP0_CAUSE - cfc0 t1, CP0_S1_INTCONTROL - - /* shift the mask 8 bits left to line up the bits */ - sll t2, t1, 8 - - and t0, t2 - srl t0, t0, 16 - - andi t1, t0, STATUSF_IP8 /* int6 hardware line */ - bnez t1, ll_galileo_p1_irq - andi t1, t0, STATUSF_IP9 /* int7 hardware line */ - bnez t1, ll_pmc_irq - andi t1, t0, STATUSF_IP10 /* int8 hardware line */ - bnez t1, ll_cpci_abcd_irq - andi t1, t0, STATUSF_IP11 /* int9 hardware line */ - bnez t1, ll_testpoint_irq - - .set reorder - - /* wrong alarm or masked ... */ - j spurious_interrupt - nop - END(ocelot_handle_int) - - .align 5 -ll_pri_enet_irq: - li a0, 2 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_sec_enet_irq: - li a0, 3 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_uart_irq: - li a0, 4 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_cpci_irq: - li a0, 5 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_galileo_p0_irq: - li a0, 6 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_cputimer_irq: - li a0, 7 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_galileo_p1_irq: - li a0, 8 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_pmc_irq: - li a0, 9 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_cpci_abcd_irq: - li a0, 10 - move a1, sp - jal do_IRQ - j ret_from_irq - -ll_testpoint_irq: - li a0, 11 - move a1, sp - jal do_IRQ - j ret_from_irq diff --git a/arch/mips/momentum/ocelot_g/irq.c b/arch/mips/momentum/ocelot_g/irq.c deleted file mode 100644 index 5eb85b16420..00000000000 --- a/arch/mips/momentum/ocelot_g/irq.c +++ /dev/null @@ -1,69 +0,0 @@ -/* - * Copyright (C) 2000 RidgeRun, Inc. - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * Copyright (C) 2000, 01, 05 Ralf Baechle (ralf@linux-mips.org) - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/kernel_stat.h> -#include <linux/module.h> -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/types.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/timex.h> -#include <linux/slab.h> -#include <linux/random.h> -#include <linux/bitops.h> -#include <asm/bootinfo.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/irq_cpu.h> -#include <asm/mipsregs.h> -#include <asm/system.h> - -extern asmlinkage void ocelot_handle_int(void); -extern void gt64240_irq_init(void); - -void __init arch_init_irq(void) -{ - /* - * Clear all of the interrupts while we change the able around a bit. - * int-handler is not on bootstrap - */ - clear_c0_status(ST0_IM); - local_irq_disable(); - - /* Sets the first-level interrupt dispatcher. */ - set_except_vector(0, ocelot_handle_int); - mips_cpu_irq_init(0); - rm7k_cpu_irq_init(8); - - gt64240_irq_init(); -} diff --git a/arch/mips/momentum/ocelot_g/ocelot_pld.h b/arch/mips/momentum/ocelot_g/ocelot_pld.h deleted file mode 100644 index fcb8275e219..00000000000 --- a/arch/mips/momentum/ocelot_g/ocelot_pld.h +++ /dev/null @@ -1,30 +0,0 @@ -/* - * Ocelot Board Register Definitions - * - * (C) 2001 Red Hat, Inc. - * - * GPL'd - */ -#ifndef __MOMENCO_OCELOT_PLD_H__ -#define __MOMENCO_OCELOT_PLD_H__ - -#define OCELOT_CS0_ADDR (0xfc000000) - -#define OCELOT_REG_BOARDREV (0) -#define OCELOT_REG_PLD1_ID (1) -#define OCELOT_REG_PLD2_ID (2) -#define OCELOT_REG_RESET_STATUS (3) -#define OCELOT_REG_BOARD_STATUS (4) -#define OCELOT_REG_CPCI_ID (5) -#define OCELOT_REG_I2C_CTRL (8) -#define OCELOT_REG_EEPROM_MODE (9) -#define OCELOT_REG_INTMASK (10) -#define OCELOT_REG_INTSTATUS (11) -#define OCELOT_REG_INTSET (12) -#define OCELOT_REG_INTCLR (13) - -#define OCELOT_PLD_WRITE(x, y) writeb(x, OCELOT_CS0_ADDR + OCELOT_REG_##y) -#define OCELOT_PLD_READ(x) readb(OCELOT_CS0_ADDR + OCELOT_REG_##x) - - -#endif /* __MOMENCO_OCELOT_PLD_H__ */ diff --git a/arch/mips/momentum/ocelot_g/prom.c b/arch/mips/momentum/ocelot_g/prom.c deleted file mode 100644 index 6b4f577c275..00000000000 --- a/arch/mips/momentum/ocelot_g/prom.c +++ /dev/null @@ -1,86 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Based on Ocelot Linux port, which is - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <linux/config.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/sched.h> -#include <linux/bootmem.h> - -#include <asm/addrspace.h> -#include <asm/bootinfo.h> -#include <asm/pmon.h> -#include <asm/gt64240.h> - -#include "ocelot_pld.h" - -struct callvectors* debug_vectors; - -extern unsigned long marvell_base; -extern unsigned long bus_clock; - -#ifdef CONFIG_GALILLEO_GT64240_ETH -extern unsigned char prom_mac_addr_base[6]; -#endif - -const char *get_system_type(void) -{ - return "Momentum Ocelot"; -} - -void __init prom_init(void) -{ - int argc = fw_arg0; - char **arg = (char **) fw_arg1; - char **env = (char **) fw_arg2; - struct callvectors *cv = (struct callvectors *) fw_arg3; - int i; - - /* save the PROM vectors for debugging use */ - debug_vectors = cv; - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - for (i = 1; i < argc; i++) { - if (strlen(arcs_cmdline) + strlen(arg[i] + 1) - >= sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, arg[i]); - strcat(arcs_cmdline, " "); - } - - mips_machgroup = MACH_GROUP_MOMENCO; - mips_machtype = MACH_MOMENCO_OCELOT_G; - -#ifdef CONFIG_GALILLEO_GT64240_ETH - /* get the base MAC address for on-board ethernet ports */ - memcpy(prom_mac_addr_base, (void*)0xfc807cf2, 6); -#endif - - while (*env) { - if (strncmp("gtbase", *env, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(*env + strlen("gtbase="), - NULL, 16); - } - if (strncmp("busclock", *env, strlen("busclock")) == 0) { - bus_clock = simple_strtol(*env + strlen("busclock="), - NULL, 10); - } - env++; - } -} - -unsigned long __init prom_free_prom_memory(void) -{ - return 0; -} diff --git a/arch/mips/momentum/ocelot_g/reset.c b/arch/mips/momentum/ocelot_g/reset.c deleted file mode 100644 index 3fd499adf4c..00000000000 --- a/arch/mips/momentum/ocelot_g/reset.c +++ /dev/null @@ -1,47 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Copyright (C) 1997, 2001 Ralf Baechle - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - */ -#include <linux/sched.h> -#include <linux/mm.h> -#include <asm/io.h> -#include <asm/pgtable.h> -#include <asm/processor.h> -#include <asm/reboot.h> -#include <asm/system.h> -#include <linux/delay.h> - -void momenco_ocelot_restart(char *command) -{ - void *nvram = ioremap_nocache(0x2c807000, 0x1000); - - if (!nvram) { - printk(KERN_NOTICE "ioremap of reset register failed\n"); - return; - } - writeb(0x84, nvram + 0xff7); /* Ask the NVRAM/RTC/watchdog chip to - assert reset in 1/16 second */ - mdelay(10+(1000/16)); - iounmap(nvram); - printk(KERN_NOTICE "Watchdog reset failed\n"); -} - -void momenco_ocelot_halt(void) -{ - printk(KERN_NOTICE "\n** You can safely turn off the power\n"); - while (1) - __asm__(".set\tmips3\n\t" - "wait\n\t" - ".set\tmips0"); -} - -void momenco_ocelot_power_off(void) -{ - momenco_ocelot_halt(); -} diff --git a/arch/mips/momentum/ocelot_g/setup.c b/arch/mips/momentum/ocelot_g/setup.c deleted file mode 100644 index 38a78ab8c83..00000000000 --- a/arch/mips/momentum/ocelot_g/setup.c +++ /dev/null @@ -1,266 +0,0 @@ -/* - * BRIEF MODULE DESCRIPTION - * Momentum Computer Ocelot-G (CP7000G) - board dependent boot routines - * - * Copyright (C) 1996, 1997, 2001 Ralf Baechle - * Copyright (C) 2000 RidgeRun, Inc. - * Copyright (C) 2001 Red Hat, Inc. - * Copyright (C) 2002 Momentum Computer - * - * Author: Matthew Dharm, Momentum Computer - * mdharm@momenco.com - * - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -#include <linux/config.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/mm.h> -#include <linux/swap.h> -#include <linux/ioport.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/timex.h> -#include <linux/vmalloc.h> -#include <asm/time.h> -#include <asm/bootinfo.h> -#include <asm/page.h> -#include <asm/io.h> -#include <asm/gt64240.h> -#include <asm/irq.h> -#include <asm/pci.h> -#include <asm/processor.h> -#include <asm/ptrace.h> -#include <asm/reboot.h> -#include <linux/bootmem.h> - -#include "ocelot_pld.h" - -#ifdef CONFIG_GALILLEO_GT64240_ETH -extern unsigned char prom_mac_addr_base[6]; -#endif - -unsigned long marvell_base; - -/* These functions are used for rebooting or halting the machine*/ -extern void momenco_ocelot_restart(char *command); -extern void momenco_ocelot_halt(void); -extern void momenco_ocelot_power_off(void); - -extern void gt64240_time_init(void); -extern void momenco_ocelot_irq_setup(void); - -static char reset_reason; - -static unsigned long ENTRYLO(unsigned long paddr) -{ - return ((paddr & PAGE_MASK) | - (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL | - _CACHE_UNCACHED)) >> 6; -} - -/* setup code for a handoff from a version 2 PMON 2000 PROM */ -void PMON_v2_setup(void) -{ - /* A wired TLB entry for the GT64240 and the serial port. The - GT64240 is going to be hit on every IRQ anyway - there's - absolutely no point in letting it be a random TLB entry, as - it'll just cause needless churning of the TLB. And we use - the other half for the serial port, which is just a PITA - otherwise :) - - Device Physical Virtual - GT64240 Internal Regs 0xf4000000 0xe0000000 - UARTs (CS2) 0xfd000000 0xe0001000 - */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), - 0xf4000000, PM_64K); - add_wired_entry(ENTRYLO(0xfd000000), ENTRYLO(0xfd001000), - 0xfd000000, PM_4K); - - /* Also a temporary entry to let us talk to the Ocelot PLD and NVRAM - in the CS[012] region. We can't use ioremap() yet. The NVRAM - is a ST M48T37Y, which includes NVRAM, RTC, and Watchdog functions. - - Ocelot PLD (CS0) 0xfc000000 0xe0020000 - NVRAM (CS1) 0xfc800000 0xe0030000 - */ - add_temporary_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfc010000), - 0xfc000000, PM_64K); - add_temporary_entry(ENTRYLO(0xfc800000), ENTRYLO(0xfc810000), - 0xfc800000, PM_64K); - - marvell_base = 0xf4000000; -} - -extern int rm7k_tcache_enabled; - -/* - * This runs in KSEG1. See the verbiage in rm7k.c::probe_scache() - */ -#define Page_Invalidate_T 0x16 -static void __init setup_l3cache(unsigned long size) -{ - int register i; - - printk("Enabling L3 cache..."); - - /* Enable the L3 cache in the GT64120A's CPU Configuration register */ - MV_WRITE(0, MV_READ(0) | (1<<14)); - - /* Enable the L3 cache in the CPU */ - set_c0_config(1<<12 /* CONF_TE */); - - /* Clear the cache */ - write_c0_taglo(0); - write_c0_taghi(0); - - for (i=0; i < size; i+= 4096) { - __asm__ __volatile__ ( - ".set noreorder\n\t" - ".set mips3\n\t" - "cache %1, (%0)\n\t" - ".set mips0\n\t" - ".set reorder" - : - : "r" (KSEG0ADDR(i)), - "i" (Page_Invalidate_T)); - } - - /* Let the RM7000 MM code know that the tertiary cache is enabled */ - rm7k_tcache_enabled = 1; - - printk("Done\n"); -} - -static int __init momenco_ocelot_g_setup(void) -{ - void (*l3func)(unsigned long) = (void *) KSEG1ADDR(setup_l3cache); - unsigned int tmpword; - - board_time_init = gt64240_time_init; - - _machine_restart = momenco_ocelot_restart; - _machine_halt = momenco_ocelot_halt; - _machine_power_off = momenco_ocelot_power_off; - - /* - * initrd_start = (ulong)ocelot_initrd_start; - * initrd_end = (ulong)ocelot_initrd_start + (ulong)ocelot_initrd_size; - * initrd_below_start_ok = 1; - */ - - /* do handoff reconfiguration */ - PMON_v2_setup(); - -#ifdef CONFIG_GALILLEO_GT64240_ETH - /* get the mac addr */ - memcpy(prom_mac_addr_base, (void*)0xfc807cf2, 6); -#endif - - /* Turn off the Bit-Error LED */ - OCELOT_PLD_WRITE(0x80, INTCLR); - - tmpword = OCELOT_PLD_READ(BOARDREV); - if (tmpword < 26) - printk("Momenco Ocelot-G: Board Assembly Rev. %c\n", 'A'+tmpword); - else - printk("Momenco Ocelot-G: Board Assembly Revision #0x%x\n", tmpword); - - tmpword = OCELOT_PLD_READ(PLD1_ID); - printk("PLD 1 ID: %d.%d\n", tmpword>>4, tmpword&15); - tmpword = OCELOT_PLD_READ(PLD2_ID); - printk("PLD 2 ID: %d.%d\n", tmpword>>4, tmpword&15); - tmpword = OCELOT_PLD_READ(RESET_STATUS); - printk("Reset reason: 0x%x\n", tmpword); - reset_reason = tmpword; - OCELOT_PLD_WRITE(0xff, RESET_STATUS); - - tmpword = OCELOT_PLD_READ(BOARD_STATUS); - printk("Board Status register: 0x%02x\n", tmpword); - printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent"); - printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent"); - printk(" - Tulip PHY %s connected\n", (tmpword&0x10)?"is":"not"); - printk(" - L3 Cache size: %d MiB\n", (1<<((tmpword&12) >> 2))&~1); - printk(" - SDRAM size: %d MiB\n", 1<<(6+(tmpword&3))); - - if (tmpword&12) - l3func((1<<(((tmpword&12) >> 2)+20))); - - switch(tmpword &3) { - case 3: - /* 512MiB -- two banks of 256MiB */ - add_memory_region( 0x0<<20, 0x100<<20, BOOT_MEM_RAM); -/* - add_memory_region(0x100<<20, 0x100<<20, BOOT_MEM_RAM); -*/ - break; - case 2: - /* 256MiB -- two banks of 128MiB */ - add_memory_region( 0x0<<20, 0x80<<20, BOOT_MEM_RAM); - add_memory_region(0x80<<20, 0x80<<20, BOOT_MEM_RAM); - break; - case 1: - /* 128MiB -- 64MiB per bank */ - add_memory_region( 0x0<<20, 0x40<<20, BOOT_MEM_RAM); - add_memory_region(0x40<<20, 0x40<<20, BOOT_MEM_RAM); - break; - case 0: - /* 64MiB */ - add_memory_region( 0x0<<20, 0x40<<20, BOOT_MEM_RAM); - break; - } - - /* FIXME: Fix up the DiskOnChip mapping */ - MV_WRITE(0x468, 0xfef73); - - return 0; -} - -early_initcall(momenco_ocelot_g_setup); - -/* This needs to be one of the first initcalls, because no I/O port access - can work before this */ - -static int io_base_ioremap(void) -{ - /* we're mapping PCI accesses from 0xc0000000 to 0xf0000000 */ - unsigned long io_remap_range; - - io_remap_range = (unsigned long) ioremap(0xc0000000, 0x30000000); - if (!io_remap_range) - panic("Could not ioremap I/O port range"); - - set_io_port_base(io_remap_range - 0xc0000000); - - return 0; -} - -module_init(io_base_ioremap); |