diff options
Diffstat (limited to 'arch/mips/alchemy/common/power.c')
| -rw-r--r-- | arch/mips/alchemy/common/power.c | 115 |
1 files changed, 16 insertions, 99 deletions
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c index 6ab7b42aa1b..bdb28dee8fd 100644 --- a/arch/mips/alchemy/common/power.c +++ b/arch/mips/alchemy/common/power.c @@ -29,18 +29,12 @@ * 675 Mass Ave, Cambridge, MA 02139, USA. */ -#include <linux/init.h> #include <linux/pm.h> #include <linux/sysctl.h> #include <linux/jiffies.h> #include <asm/uaccess.h> #include <asm/mach-au1x00/au1000.h> -#if defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) -#include <asm/mach-au1x00/au1xxx_dbdma.h> -#endif - -#ifdef CONFIG_PM /* * We need to save/restore a bunch of core registers that are @@ -52,12 +46,6 @@ * We only have to save/restore registers that aren't otherwise * done as part of a driver pm_* function. */ -static unsigned int sleep_uart0_inten; -static unsigned int sleep_uart0_fifoctl; -static unsigned int sleep_uart0_linectl; -static unsigned int sleep_uart0_clkdiv; -static unsigned int sleep_uart0_enable; -static unsigned int sleep_usb[2]; static unsigned int sleep_sys_clocks[5]; static unsigned int sleep_sys_pinfunc; static unsigned int sleep_static_memctlr[4][3]; @@ -65,50 +53,6 @@ static unsigned int sleep_static_memctlr[4][3]; static void save_core_regs(void) { - extern void save_au1xxx_intctl(void); - extern void pm_eth0_shutdown(void); - - /* - * Do the serial ports.....these really should be a pm_* - * registered function by the driver......but of course the - * standard serial driver doesn't understand our Au1xxx - * unique registers. - */ - sleep_uart0_inten = au_readl(UART0_ADDR + UART_IER); - sleep_uart0_fifoctl = au_readl(UART0_ADDR + UART_FCR); - sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR); - sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK); - sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL); - au_sync(); - -#ifndef CONFIG_SOC_AU1200 - /* Shutdown USB host/device. */ - sleep_usb[0] = au_readl(USB_HOST_CONFIG); - - /* There appears to be some undocumented reset register.... */ - au_writel(0, 0xb0100004); - au_sync(); - au_writel(0, USB_HOST_CONFIG); - au_sync(); - - sleep_usb[1] = au_readl(USBD_ENABLE); - au_writel(0, USBD_ENABLE); - au_sync(); - -#else /* AU1200 */ - - /* enable access to OTG mmio so we can save OTG CAP/MUX. - * FIXME: write an OTG driver and move this stuff there! - */ - au_writel(au_readl(USB_MSR_BASE + 4) | (1 << 6), USB_MSR_BASE + 4); - au_sync(); - sleep_usb[0] = au_readl(0xb4020020); /* OTG_CAP */ - sleep_usb[1] = au_readl(0xb4020024); /* OTG_MUX */ -#endif - - /* Save interrupt controller state. */ - save_au1xxx_intctl(); - /* Clocks and PLLs. */ sleep_sys_clocks[0] = au_readl(SYS_FREQCTRL0); sleep_sys_clocks[1] = au_readl(SYS_FREQCTRL1); @@ -132,10 +76,6 @@ static void save_core_regs(void) sleep_static_memctlr[3][0] = au_readl(MEM_STCFG3); sleep_static_memctlr[3][1] = au_readl(MEM_STTIME3); sleep_static_memctlr[3][2] = au_readl(MEM_STADDR3); - -#if defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) - au1xxx_dbdma_suspend(); -#endif } static void restore_core_regs(void) @@ -156,22 +96,6 @@ static void restore_core_regs(void) au_writel(sleep_sys_pinfunc, SYS_PINFUNC); au_sync(); -#ifndef CONFIG_SOC_AU1200 - au_writel(sleep_usb[0], USB_HOST_CONFIG); - au_writel(sleep_usb[1], USBD_ENABLE); - au_sync(); -#else - /* enable accces to OTG memory */ - au_writel(au_readl(USB_MSR_BASE + 4) | (1 << 6), USB_MSR_BASE + 4); - au_sync(); - - /* restore OTG caps and port mux. */ - au_writel(sleep_usb[0], 0xb4020020 + 0); /* OTG_CAP */ - au_sync(); - au_writel(sleep_usb[1], 0xb4020020 + 4); /* OTG_MUX */ - au_sync(); -#endif - /* Restore the static memory controller configuration. */ au_writel(sleep_static_memctlr[0][0], MEM_STCFG0); au_writel(sleep_static_memctlr[0][1], MEM_STTIME0); @@ -185,33 +109,26 @@ static void restore_core_regs(void) au_writel(sleep_static_memctlr[3][0], MEM_STCFG3); au_writel(sleep_static_memctlr[3][1], MEM_STTIME3); au_writel(sleep_static_memctlr[3][2], MEM_STADDR3); - - /* - * Enable the UART if it was enabled before sleep. - * I guess I should define module control bits........ - */ - if (sleep_uart0_enable & 0x02) { - au_writel(0, UART0_ADDR + UART_MOD_CNTRL); au_sync(); - au_writel(1, UART0_ADDR + UART_MOD_CNTRL); au_sync(); - au_writel(3, UART0_ADDR + UART_MOD_CNTRL); au_sync(); - au_writel(sleep_uart0_inten, UART0_ADDR + UART_IER); au_sync(); - au_writel(sleep_uart0_fifoctl, UART0_ADDR + UART_FCR); au_sync(); - au_writel(sleep_uart0_linectl, UART0_ADDR + UART_LCR); au_sync(); - au_writel(sleep_uart0_clkdiv, UART0_ADDR + UART_CLK); au_sync(); - } - - restore_au1xxx_intctl(); - -#if defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) - au1xxx_dbdma_resume(); -#endif } void au_sleep(void) { save_core_regs(); - au1xxx_save_and_sleep(); + + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1000: + case ALCHEMY_CPU_AU1500: + case ALCHEMY_CPU_AU1100: + alchemy_sleep_au1000(); + break; + case ALCHEMY_CPU_AU1550: + case ALCHEMY_CPU_AU1200: + alchemy_sleep_au1550(); + break; + case ALCHEMY_CPU_AU1300: + alchemy_sleep_au1300(); + break; + } + restore_core_regs(); } - -#endif /* CONFIG_PM */ |