aboutsummaryrefslogtreecommitdiff
path: root/arch/cris/arch-v32
diff options
context:
space:
mode:
Diffstat (limited to 'arch/cris/arch-v32')
-rw-r--r--arch/cris/arch-v32/drivers/Kconfig409
-rw-r--r--arch/cris/arch-v32/drivers/axisflashmap.c2
-rw-r--r--arch/cris/arch-v32/drivers/mach-a3/gpio.c2
-rw-r--r--arch/cris/arch-v32/drivers/mach-fs/gpio.c10
-rw-r--r--arch/cris/arch-v32/drivers/sync_serial.c4
-rw-r--r--arch/cris/arch-v32/kernel/entry.S34
-rw-r--r--arch/cris/arch-v32/kernel/fasttimer.c301
-rw-r--r--arch/cris/arch-v32/kernel/irq.c10
-rw-r--r--arch/cris/arch-v32/kernel/process.c15
-rw-r--r--arch/cris/arch-v32/kernel/smp.c8
-rw-r--r--arch/cris/arch-v32/kernel/time.c6
-rw-r--r--arch/cris/arch-v32/mach-a3/Kconfig4
-rw-r--r--arch/cris/arch-v32/mach-a3/Makefile1
-rw-r--r--arch/cris/arch-v32/mach-a3/arbiter.c4
-rw-r--r--arch/cris/arch-v32/mach-a3/cpufreq.c152
-rw-r--r--arch/cris/arch-v32/mach-fs/Makefile1
-rw-r--r--arch/cris/arch-v32/mach-fs/arbiter.c2
-rw-r--r--arch/cris/arch-v32/mach-fs/cpufreq.c145
18 files changed, 185 insertions, 925 deletions
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index af4a486dadc..15a9ed1d579 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -2,9 +2,7 @@ if ETRAX_ARCH_V32
config ETRAX_ETHERNET
bool "Ethernet support"
- depends on ETRAX_ARCH_V32
- select ETHERNET
- select NET_CORE
+ depends on ETRAX_ARCH_V32 && NETDEVICES
select MII
help
This option enables the ETRAX FS built-in 10/100Mbit Ethernet
@@ -13,7 +11,6 @@ config ETRAX_ETHERNET
config ETRAX_NO_PHY
bool "PHY not present"
depends on ETRAX_ETHERNET
- default N
help
This option disables all MDIO communication with an ethernet
transceiver connected to the MII interface. This option shall
@@ -21,64 +18,6 @@ config ETRAX_NO_PHY
switch. This option should normally be disabled. If enabled,
speed and duplex will be locked to 100 Mbit and full duplex.
-config ETRAX_ETHERNET_IFACE0
- depends on ETRAX_ETHERNET
- bool "Enable network interface 0"
-
-config ETRAX_ETHERNET_IFACE1
- depends on (ETRAX_ETHERNET && ETRAXFS)
- bool "Enable network interface 1 (uses DMA6 and DMA7)"
-
-config ETRAX_ETHERNET_GBIT
- depends on (ETRAX_ETHERNET && CRIS_MACH_ARTPEC3)
- bool "Enable gigabit Ethernet support"
-
-choice
- prompt "Eth0 led group"
- depends on ETRAX_ETHERNET_IFACE0
- default ETRAX_ETH0_USE_LEDGRP0
-
-config ETRAX_ETH0_USE_LEDGRP0
- bool "Use LED grp 0"
- depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
- help
- Use LED grp 0 for eth0
-
-config ETRAX_ETH0_USE_LEDGRP1
- bool "Use LED grp 1"
- depends on ETRAX_NBR_LED_GRP_TWO
- help
- Use LED grp 1 for eth0
-
-config ETRAX_ETH0_USE_LEDGRPNULL
- bool "Use no LEDs for eth0"
- help
- Use no LEDs for eth0
-endchoice
-
-choice
- prompt "Eth1 led group"
- depends on ETRAX_ETHERNET_IFACE1
- default ETRAX_ETH1_USE_LEDGRP1
-
-config ETRAX_ETH1_USE_LEDGRP0
- bool "Use LED grp 0"
- depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
- help
- Use LED grp 0 for eth1
-
-config ETRAX_ETH1_USE_LEDGRP1
- bool "Use LED grp 1"
- depends on ETRAX_NBR_LED_GRP_TWO
- help
- Use LED grp 1 for eth1
-
-config ETRAX_ETH1_USE_LEDGRPNULL
- bool "Use no LEDs for eth1"
- help
- Use no LEDs for eth1
-endchoice
-
config ETRAXFS_SERIAL
bool "Serial-port support"
depends on ETRAX_ARCH_V32
@@ -110,261 +49,24 @@ config ETRAX_SERIAL_PORT0
if you do not need DMA to something else.
ser0 can use dma4 or dma6 for output and dma5 or dma7 for input.
-choice
- prompt "Ser0 default port type "
- depends on ETRAX_SERIAL_PORT0
- default ETRAX_SERIAL_PORT0_TYPE_232
- help
- Type of serial port.
-
-config ETRAX_SERIAL_PORT0_TYPE_232
- bool "Ser0 is a RS-232 port"
- help
- Configure serial port 0 to be a RS-232 port.
-
-config ETRAX_SERIAL_PORT0_TYPE_485HD
- bool "Ser0 is a half duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 0 to be a half duplex (two wires) RS-485 port.
-
-config ETRAX_SERIAL_PORT0_TYPE_485FD
- bool "Ser0 is a full duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 0 to be a full duplex (four wires) RS-485 port.
-endchoice
-
-config ETRAX_SER0_DTR_BIT
- string "Ser 0 DTR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT0
-
-config ETRAX_SER0_RI_BIT
- string "Ser 0 RI bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT0
-
-config ETRAX_SER0_DSR_BIT
- string "Ser 0 DSR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT0
-
-config ETRAX_SER0_CD_BIT
- string "Ser 0 CD bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT0
-
config ETRAX_SERIAL_PORT1
bool "Serial port 1 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser1 (ttyS1).
-choice
- prompt "Ser1 default port type"
- depends on ETRAX_SERIAL_PORT1
- default ETRAX_SERIAL_PORT1_TYPE_232
- help
- Type of serial port.
-
-config ETRAX_SERIAL_PORT1_TYPE_232
- bool "Ser1 is a RS-232 port"
- help
- Configure serial port 1 to be a RS-232 port.
-
-config ETRAX_SERIAL_PORT1_TYPE_485HD
- bool "Ser1 is a half duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 1 to be a half duplex (two wires) RS-485 port.
-
-config ETRAX_SERIAL_PORT1_TYPE_485FD
- bool "Ser1 is a full duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 1 to be a full duplex (four wires) RS-485 port.
-endchoice
-
-config ETRAX_SER1_DTR_BIT
- string "Ser 1 DTR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT1
-
-config ETRAX_SER1_RI_BIT
- string "Ser 1 RI bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT1
-
-config ETRAX_SER1_DSR_BIT
- string "Ser 1 DSR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT1
-
-config ETRAX_SER1_CD_BIT
- string "Ser 1 CD bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT1
-
config ETRAX_SERIAL_PORT2
bool "Serial port 2 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser2 (ttyS2).
-choice
- prompt "Ser2 default port type"
- depends on ETRAX_SERIAL_PORT2
- default ETRAX_SERIAL_PORT2_TYPE_232
- help
- What DMA channel to use for ser2
-
-config ETRAX_SERIAL_PORT2_TYPE_232
- bool "Ser2 is a RS-232 port"
- help
- Configure serial port 2 to be a RS-232 port.
-
-config ETRAX_SERIAL_PORT2_TYPE_485HD
- bool "Ser2 is a half duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 2 to be a half duplex (two wires) RS-485 port.
-
-config ETRAX_SERIAL_PORT2_TYPE_485FD
- bool "Ser2 is a full duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 2 to be a full duplex (four wires) RS-485 port.
-endchoice
-
-
-config ETRAX_SER2_DTR_BIT
- string "Ser 2 DTR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT2
-
-config ETRAX_SER2_RI_BIT
- string "Ser 2 RI bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT2
-
-config ETRAX_SER2_DSR_BIT
- string "Ser 2 DSR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT2
-
-config ETRAX_SER2_CD_BIT
- string "Ser 2 CD bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT2
-
config ETRAX_SERIAL_PORT3
bool "Serial port 3 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser3 (ttyS3).
-choice
- prompt "Ser3 default port type"
- depends on ETRAX_SERIAL_PORT3
- default ETRAX_SERIAL_PORT3_TYPE_232
- help
- What DMA channel to use for ser3.
-
-config ETRAX_SERIAL_PORT3_TYPE_232
- bool "Ser3 is a RS-232 port"
- help
- Configure serial port 3 to be a RS-232 port.
-
-config ETRAX_SERIAL_PORT3_TYPE_485HD
- bool "Ser3 is a half duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 3 to be a half duplex (two wires) RS-485 port.
-
-config ETRAX_SERIAL_PORT3_TYPE_485FD
- bool "Ser3 is a full duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 3 to be a full duplex (four wires) RS-485 port.
-endchoice
-
-config ETRAX_SER3_DTR_BIT
- string "Ser 3 DTR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT3
-
-config ETRAX_SER3_RI_BIT
- string "Ser 3 RI bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT3
-
-config ETRAX_SER3_DSR_BIT
- string "Ser 3 DSR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT3
-
-config ETRAX_SER3_CD_BIT
- string "Ser 3 CD bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT3
-
-config ETRAX_SERIAL_PORT4
- bool "Serial port 4 enabled"
- depends on ETRAXFS_SERIAL && CRIS_MACH_ARTPEC3
- help
- Enables the ETRAX FS serial driver for ser4 (ttyS4).
-
-choice
- prompt "Ser4 default port type"
- depends on ETRAX_SERIAL_PORT4
- default ETRAX_SERIAL_PORT4_TYPE_232
- help
- What DMA channel to use for ser4.
-
-config ETRAX_SERIAL_PORT4_TYPE_232
- bool "Ser4 is a RS-232 port"
- help
- Configure serial port 4 to be a RS-232 port.
-
-config ETRAX_SERIAL_PORT4_TYPE_485HD
- bool "Ser4 is a half duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 4 to be a half duplex (two wires) RS-485 port.
-
-config ETRAX_SERIAL_PORT4_TYPE_485FD
- bool "Ser4 is a full duplex RS-485 port"
- depends on ETRAX_RS485
- help
- Configure serial port 4 to be a full duplex (four wires) RS-485 port.
-endchoice
-
-choice
- prompt "Ser4 DMA in channel "
- depends on ETRAX_SERIAL_PORT4
- default ETRAX_SERIAL_PORT4_NO_DMA_IN
- help
- What DMA channel to use for ser4.
-
-
-config ETRAX_SERIAL_PORT4_NO_DMA_IN
- bool "Ser4 uses no DMA for input"
- help
- Do not use DMA for ser4 input.
-
-config ETRAX_SERIAL_PORT4_DMA9_IN
- bool "Ser4 uses DMA9 for input"
- depends on ETRAX_SERIAL_PORT4
- help
- Enables the DMA9 input channel for ser4 (ttyS4).
- If you do not enable DMA, an interrupt for each character will be
- used when receiving data.
- Normally you want to use DMA, unless you use the DMA channel for
- something else.
-
-endchoice
-
-config ETRAX_SER4_DTR_BIT
- string "Ser 4 DTR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT4
-
-config ETRAX_SER4_RI_BIT
- string "Ser 4 RI bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT4
-
-config ETRAX_SER4_DSR_BIT
- string "Ser 4 DSR bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT4
-
-config ETRAX_SER4_CD_BIT
- string "Ser 4 CD bit (empty = not used)"
- depends on ETRAX_SERIAL_PORT4
-
config ETRAX_SYNCHRONOUS_SERIAL
bool "Synchronous serial-port support"
depends on ETRAX_ARCH_V32
@@ -404,7 +106,6 @@ config ETRAX_AXISFLASHMAP
select MTD_CFI
select MTD_CFI_AMDSTD
select MTD_JEDECPROBE
- select MTD_CHAR
select MTD_BLOCK
select MTD_COMPLEX_MAPPINGS
help
@@ -414,7 +115,6 @@ config ETRAX_AXISFLASHMAP
config ETRAX_AXISFLASHMAP_MTD0WHOLE
bool "MTD0 is whole boot flash device"
depends on ETRAX_AXISFLASHMAP
- default N
help
When this option is not set, mtd0 refers to the first partition
on the boot flash device. When set, mtd0 refers to the whole
@@ -618,7 +318,6 @@ config ETRAX_PV_CHANGEABLE_BITS
config ETRAX_CARDBUS
bool "Cardbus support"
depends on ETRAX_ARCH_V32
- select HOTPLUG
help
Enabled the ETRAX Cardbus driver.
@@ -642,8 +341,6 @@ config ETRAX_STREAMCOPROC
This option enables a driver for the stream co-processor
for cryptographic operations.
-source drivers/mmc/Kconfig
-
config ETRAX_MMC_IOP
tristate "MMC/SD host driver using IO-processor"
depends on ETRAX_ARCH_V32 && MMC
@@ -709,32 +406,6 @@ config ETRAX_SPI_SSER0
want to build it as a module, which will be named spi_crisv32_sser.
(You need to select MMC separately.)
-config ETRAX_SPI_SSER0_DMA
- bool "DMA for SPI on sser0 enabled"
- depends on ETRAX_SPI_SSER0
- depends on !ETRAX_SERIAL_PORT1_DMA4_OUT && !ETRAX_SERIAL_PORT1_DMA5_IN
- default y
- help
- Say Y if using DMA (dma4/dma5) for SPI on synchronous serial port 0.
-
-config ETRAX_SPI_MMC_CD_SSER0_PIN
- string "MMC/SD card detect pin for SPI on sser0"
- depends on ETRAX_SPI_SSER0 && MMC_SPI
- default "pd11"
- help
- The pin to use for SD/MMC card detect. This pin should be pulled up
- and grounded when a card is present. If defined as " " (space), no
- pin is selected. A card must then always be inserted for proper
- action.
-
-config ETRAX_SPI_MMC_WP_SSER0_PIN
- string "MMC/SD card write-protect pin for SPI on sser0"
- depends on ETRAX_SPI_SSER0 && MMC_SPI
- default "pd10"
- help
- The pin to use for the SD/MMC write-protect signal for a memory
- card. If defined as " " (space), the card is considered writable.
-
config ETRAX_SPI_SSER1
tristate "SPI using synchronous serial port 1 (sser1)"
depends on ETRAX_SPI_MMC
@@ -748,32 +419,6 @@ config ETRAX_SPI_SSER1
want to build it as a module, which will be named spi_crisv32_sser.
(You need to select MMC separately.)
-config ETRAX_SPI_SSER1_DMA
- bool "DMA for SPI on sser1 enabled"
- depends on ETRAX_SPI_SSER1 && !ETRAX_ETHERNET_IFACE1
- depends on !ETRAX_SERIAL_PORT0_DMA6_OUT && !ETRAX_SERIAL_PORT0_DMA7_IN
- default y
- help
- Say Y if using DMA (dma6/dma7) for SPI on synchronous serial port 1.
-
-config ETRAX_SPI_MMC_CD_SSER1_PIN
- string "MMC/SD card detect pin for SPI on sser1"
- depends on ETRAX_SPI_SSER1 && MMC_SPI
- default "pd12"
- help
- The pin to use for SD/MMC card detect. This pin should be pulled up
- and grounded when a card is present. If defined as " " (space), no
- pin is selected. A card must then always be inserted for proper
- action.
-
-config ETRAX_SPI_MMC_WP_SSER1_PIN
- string "MMC/SD card write-protect pin for SPI on sser1"
- depends on ETRAX_SPI_SSER1 && MMC_SPI
- default "pd9"
- help
- The pin to use for the SD/MMC write-protect signal for a memory
- card. If defined as " " (space), the card is considered writable.
-
config ETRAX_SPI_GPIO
tristate "Bitbanged SPI using gpio pins"
depends on ETRAX_SPI_MMC
@@ -788,56 +433,4 @@ config ETRAX_SPI_GPIO
Say m to build it as a module, which will be called spi_crisv32_gpio.
(You need to select MMC separately.)
-# The default match that of sser0, only because that's how it was tested.
-config ETRAX_SPI_CS_PIN
- string "SPI chip select pin"
- depends on ETRAX_SPI_GPIO
- default "pc3"
- help
- The pin to use for SPI chip select.
-
-config ETRAX_SPI_CLK_PIN
- string "SPI clock pin"
- depends on ETRAX_SPI_GPIO
- default "pc1"
- help
- The pin to use for the SPI clock.
-
-config ETRAX_SPI_DATAIN_PIN
- string "SPI MISO (data in) pin"
- depends on ETRAX_SPI_GPIO
- default "pc16"
- help
- The pin to use for SPI data in from the device.
-
-config ETRAX_SPI_DATAOUT_PIN
- string "SPI MOSI (data out) pin"
- depends on ETRAX_SPI_GPIO
- default "pc0"
- help
- The pin to use for SPI data out to the device.
-
-config ETRAX_SPI_MMC_CD_GPIO_PIN
- string "MMC/SD card detect pin for SPI using gpio (space for none)"
- depends on ETRAX_SPI_GPIO && MMC_SPI
- default "pd11"
- help
- The pin to use for SD/MMC card detect. This pin should be pulled up
- and grounded when a card is present. If defined as " " (space), no
- pin is selected. A card must then always be inserted for proper
- action.
-
-config ETRAX_SPI_MMC_WP_GPIO_PIN
- string "MMC/SD card write-protect pin for SPI using gpio (space for none)"
- depends on ETRAX_SPI_GPIO && MMC_SPI
- default "pd10"
- help
- The pin to use for the SD/MMC write-protect signal for a memory
- card. If defined as " " (space), the card is considered writable.
-
-# Avoid choices causing non-working configs by conditionalizing the inclusion.
-if ETRAX_SPI_MMC
-source drivers/spi/Kconfig
-endif
-
endif
diff --git a/arch/cris/arch-v32/drivers/axisflashmap.c b/arch/cris/arch-v32/drivers/axisflashmap.c
index 1b6ad624720..28dd77144e8 100644
--- a/arch/cris/arch-v32/drivers/axisflashmap.c
+++ b/arch/cris/arch-v32/drivers/axisflashmap.c
@@ -24,8 +24,6 @@
#include <linux/mtd/mtdram.h>
#include <linux/mtd/partitions.h>
-#include <linux/cramfs_fs.h>
-
#include <asm/axisflashmap.h>
#include <asm/mmu.h>
diff --git a/arch/cris/arch-v32/drivers/mach-a3/gpio.c b/arch/cris/arch-v32/drivers/mach-a3/gpio.c
index 0b86deedacb..74f9fe80940 100644
--- a/arch/cris/arch-v32/drivers/mach-a3/gpio.c
+++ b/arch/cris/arch-v32/drivers/mach-a3/gpio.c
@@ -978,7 +978,7 @@ static int __init gpio_init(void)
CRIS_LED_DISK_WRITE(0);
int res2 = request_irq(GIO_INTR_VECT, gpio_interrupt,
- IRQF_SHARED | IRQF_DISABLED, "gpio", &alarmlist);
+ IRQF_SHARED, "gpio", &alarmlist);
if (res2) {
printk(KERN_ERR "err: irq for gpio\n");
return res2;
diff --git a/arch/cris/arch-v32/drivers/mach-fs/gpio.c b/arch/cris/arch-v32/drivers/mach-fs/gpio.c
index a2ac0917f1a..009f4ee1bd0 100644
--- a/arch/cris/arch-v32/drivers/mach-fs/gpio.c
+++ b/arch/cris/arch-v32/drivers/mach-fs/gpio.c
@@ -958,17 +958,13 @@ gpio_init(void)
printk(KERN_INFO "ETRAX FS GPIO driver v2.5, (c) 2003-2007 "
"Axis Communications AB\n");
- /* We call etrax_gpio_wake_up_check() from timer interrupt and
- * from cpu_idle() in kernel/process.c
- * The check in cpu_idle() reduces latency from ~15 ms to ~6 ms
- * in some tests.
- */
+ /* We call etrax_gpio_wake_up_check() from timer interrupt */
if (request_irq(TIMER0_INTR_VECT, gpio_poll_timer_interrupt,
- IRQF_SHARED | IRQF_DISABLED, "gpio poll", &alarmlist))
+ IRQF_SHARED, "gpio poll", &alarmlist))
printk(KERN_ERR "timer0 irq for gpio\n");
if (request_irq(GIO_INTR_VECT, gpio_pa_interrupt,
- IRQF_SHARED | IRQF_DISABLED, "gpio PA", &alarmlist))
+ IRQF_SHARED, "gpio PA", &alarmlist))
printk(KERN_ERR "PA irq for gpio\n");
#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
diff --git a/arch/cris/arch-v32/drivers/sync_serial.c b/arch/cris/arch-v32/drivers/sync_serial.c
index 219f704e322..bbb806b6883 100644
--- a/arch/cris/arch-v32/drivers/sync_serial.c
+++ b/arch/cris/arch-v32/drivers/sync_serial.c
@@ -19,6 +19,7 @@
#include <linux/init.h>
#include <linux/timer.h>
#include <linux/spinlock.h>
+#include <linux/wait.h>
#include <asm/io.h>
#include <dma.h>
@@ -1144,7 +1145,8 @@ static ssize_t sync_serial_read(struct file * file, char * buf,
if (file->f_flags & O_NONBLOCK)
return -EAGAIN;
- interruptible_sleep_on(&port->in_wait_q);
+ wait_event_interruptible(port->in_wait_q,
+ !(start == end && !port->full));
if (signal_pending(current))
return -EINTR;
diff --git a/arch/cris/arch-v32/kernel/entry.S b/arch/cris/arch-v32/kernel/entry.S
index faa644111fe..2f19ac6217a 100644
--- a/arch/cris/arch-v32/kernel/entry.S
+++ b/arch/cris/arch-v32/kernel/entry.S
@@ -424,7 +424,7 @@ nmi_interrupt:
bpl 1f
nop
jsr handle_watchdog_bite ; In time.c.
- move.d $sp, $r10 ; Pointer to registers
+ move.d $sp, $r10 ; Pointer to registers
1: btstq REG_BIT(intr_vect, r_nmi, ext), $r0
bpl 1f
nop
@@ -452,7 +452,7 @@ spurious_interrupt:
nop
;; This handles the case when multiple interrupts arrive at the same
- ;; time. Jump to the first set interrupt bit in a priotiry fashion. The
+ ;; time. Jump to the first set interrupt bit in a priority fashion. The
;; hardware will call the unserved interrupts after the handler
;; finishes.
.type multiple_interrupt, @function
@@ -885,13 +885,29 @@ sys_call_table:
.long sys_preadv
.long sys_pwritev
.long sys_setns /* 335 */
-
- /*
- * NOTE!! This doesn't have to be exact - we just have
- * to make sure we have _enough_ of the "sys_ni_syscall"
- * entries. Don't panic if you notice that this hasn't
- * been shrunk every time we add a new system call.
- */
+ .long sys_name_to_handle_at
+ .long sys_open_by_handle_at
+ .long sys_rt_tgsigqueueinfo
+ .long sys_perf_event_open
+ .long sys_recvmmsg /* 340 */
+ .long sys_accept4
+ .long sys_fanotify_init
+ .long sys_fanotify_mark
+ .long sys_prlimit64
+ .long sys_clock_adjtime /* 345 */
+ .long sys_syncfs
+ .long sys_sendmmsg
+ .long sys_process_vm_readv
+ .long sys_process_vm_writev
+ .long sys_kcmp /* 350 */
+ .long sys_finit_module
+
+ /*
+ * NOTE!! This doesn't have to be exact - we just have
+ * to make sure we have _enough_ of the "sys_ni_syscall"
+ * entries. Don't panic if you notice that this hasn't
+ * been shrunk every time we add a new system call.
+ */
.rept NR_syscalls - (.-sys_call_table) / 4
.long sys_ni_syscall
diff --git a/arch/cris/arch-v32/kernel/fasttimer.c b/arch/cris/arch-v32/kernel/fasttimer.c
index ab1551ee43c..b130c2c5fdd 100644
--- a/arch/cris/arch-v32/kernel/fasttimer.c
+++ b/arch/cris/arch-v32/kernel/fasttimer.c
@@ -23,6 +23,7 @@
#include <hwregs/timer_defs.h>
#include <asm/fasttimer.h>
#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
/*
* timer0 is running at 100MHz and generating jiffies timer ticks
@@ -463,195 +464,161 @@ void schedule_usleep(unsigned long us)
}
#ifdef CONFIG_PROC_FS
-static int proc_fasttimer_read(char *buf, char **start, off_t offset, int len
- ,int *eof, void *data_unused);
-static struct proc_dir_entry *fasttimer_proc_entry;
-#endif /* CONFIG_PROC_FS */
-
-#ifdef CONFIG_PROC_FS
-
/* This value is very much based on testing */
#define BIG_BUF_SIZE (500 + NUM_TIMER_STATS * 300)
-static int proc_fasttimer_read(char *buf, char **start, off_t offset, int len
- ,int *eof, void *data_unused)
+static int proc_fasttimer_show(struct seq_file *m, void *v)
{
- unsigned long flags;
- int i = 0;
- int num_to_show;
+ unsigned long flags;
+ int i = 0;
+ int num_to_show;
struct fasttime_t tv;
- struct fast_timer *t, *nextt;
- static char *bigbuf = NULL;
- static unsigned long used;
-
- if (!bigbuf) {
- bigbuf = vmalloc(BIG_BUF_SIZE);
- if (!bigbuf) {
- used = 0;
- if (buf)
- buf[0] = '\0';
- return 0;
- }
- }
-
- if (!offset || !used) {
- do_gettimeofday_fast(&tv);
-
- used = 0;
- used += sprintf(bigbuf + used, "Fast timers added: %i\n",
- fast_timers_added);
- used += sprintf(bigbuf + used, "Fast timers started: %i\n",
- fast_timers_started);
- used += sprintf(bigbuf + used, "Fast timer interrupts: %i\n",
- fast_timer_ints);
- used += sprintf(bigbuf + used, "Fast timers expired: %i\n",
- fast_timers_expired);
- used += sprintf(bigbuf + used, "Fast timers deleted: %i\n",
- fast_timers_deleted);
- used += sprintf(bigbuf + used, "Fast timer running: %s\n",
- fast_timer_running ? "yes" : "no");
- used += sprintf(bigbuf + used, "Current time: %lu.%06lu\n",
- (unsigned long)tv.tv_jiff,
- (unsigned long)tv.tv_usec);
+ struct fast_timer *t, *nextt;
+
+ do_gettimeofday_fast(&tv);
+
+ seq_printf(m, "Fast timers added: %i\n", fast_timers_added);
+ seq_printf(m, "Fast timers started: %i\n", fast_timers_started);
+ seq_printf(m, "Fast timer interrupts: %i\n", fast_timer_ints);
+ seq_printf(m, "Fast timers expired: %i\n", fast_timers_expired);
+ seq_printf(m, "Fast timers deleted: %i\n", fast_timers_deleted);
+ seq_printf(m, "Fast timer running: %s\n",
+ fast_timer_running ? "yes" : "no");
+ seq_printf(m, "Current time: %lu.%06lu\n",
+ (unsigned long)tv.tv_jiff,
+ (unsigned long)tv.tv_usec);
#ifdef FAST_TIMER_SANITY_CHECKS
- used += sprintf(bigbuf + used, "Sanity failed: %i\n",
- sanity_failed);
+ seq_printf(m, "Sanity failed: %i\n", sanity_failed);
#endif
- used += sprintf(bigbuf + used, "\n");
+ seq_putc(m, '\n');
#ifdef DEBUG_LOG_INCLUDED
- {
- int end_i = debug_log_cnt;
- i = 0;
-
- if (debug_log_cnt_wrapped)
- i = debug_log_cnt;
-
- while ((i != end_i || (debug_log_cnt_wrapped && !used)) &&
- used+100 < BIG_BUF_SIZE)
- {
- used += sprintf(bigbuf + used, debug_log_string[i],
- debug_log_value[i]);
- i = (i+1) % DEBUG_LOG_MAX;
- }
- }
- used += sprintf(bigbuf + used, "\n");
+ {
+ int end_i = debug_log_cnt;
+ i = 0;
+
+ if (debug_log_cnt_wrapped)
+ i = debug_log_cnt;
+
+ while ((i != end_i || debug_log_cnt_wrapped)) {
+ if (seq_printf(m, debug_log_string[i], debug_log_value[i]) < 0)
+ return 0;
+ i = (i+1) % DEBUG_LOG_MAX;
+ }
+ }
+ seq_putc(m, '\n');
#endif
- num_to_show = (fast_timers_started < NUM_TIMER_STATS ? fast_timers_started:
- NUM_TIMER_STATS);
- used += sprintf(bigbuf + used, "Timers started: %i\n", fast_timers_started);
- for (i = 0; i < num_to_show && (used+100 < BIG_BUF_SIZE) ; i++)
- {
- int cur = (fast_timers_started - i - 1) % NUM_TIMER_STATS;
+ num_to_show = (fast_timers_started < NUM_TIMER_STATS ? fast_timers_started:
+ NUM_TIMER_STATS);
+ seq_printf(m, "Timers started: %i\n", fast_timers_started);
+ for (i = 0; i < num_to_show; i++) {
+ int cur = (fast_timers_started - i - 1) % NUM_TIMER_STATS;
#if 1 //ndef FAST_TIMER_LOG
- used += sprintf(bigbuf + used, "div: %i delay: %i"
- "\n",
- timer_div_settings[cur],
- timer_delay_settings[cur]
- );
+ seq_printf(m, "div: %i delay: %i"
+ "\n",
+ timer_div_settings[cur],
+ timer_delay_settings[cur]);
#endif
#ifdef FAST_TIMER_LOG
- t = &timer_started_log[cur];
- used += sprintf(bigbuf + used, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
- "d: %6li us data: 0x%08lX"
- "\n",
- t->name,
- (unsigned long)t->tv_set.tv_jiff,
- (unsigned long)t->tv_set.tv_usec,
- (unsigned long)t->tv_expires.tv_jiff,
- (unsigned long)t->tv_expires.tv_usec,
- t->delay_us,
- t->data
- );
+ t = &timer_started_log[cur];
+ if (seq_printf(m, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
+ "d: %6li us data: 0x%08lX"
+ "\n",
+ t->name,
+ (unsigned long)t->tv_set.tv_jiff,
+ (unsigned long)t->tv_set.tv_usec,
+ (unsigned long)t->tv_expires.tv_jiff,
+ (unsigned long)t->tv_expires.tv_usec,
+ t->delay_us,
+ t->data) < 0)
+ return 0;
#endif
- }
- used += sprintf(bigbuf + used, "\n");
+ }
+ seq_putc(m, '\n');
#ifdef FAST_TIMER_LOG
- num_to_show = (fast_timers_added < NUM_TIMER_STATS ? fast_timers_added:
- NUM_TIMER_STATS);
- used += sprintf(bigbuf + used, "Timers added: %i\n", fast_timers_added);
- for (i = 0; i < num_to_show && (used+100 < BIG_BUF_SIZE); i++)
- {
- t = &timer_added_log[(fast_timers_added - i - 1) % NUM_TIMER_STATS];
- used += sprintf(bigbuf + used, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
- "d: %6li us data: 0x%08lX"
- "\n",
- t->name,
- (unsigned long)t->tv_set.tv_jiff,
- (unsigned long)t->tv_set.tv_usec,
- (unsigned long)t->tv_expires.tv_jiff,
- (unsigned long)t->tv_expires.tv_usec,
- t->delay_us,
- t->data
- );
- }
- used += sprintf(bigbuf + used, "\n");
-
- num_to_show = (fast_timers_expired < NUM_TIMER_STATS ? fast_timers_expired:
- NUM_TIMER_STATS);
- used += sprintf(bigbuf + used, "Timers expired: %i\n", fast_timers_expired);
- for (i = 0; i < num_to_show && (used+100 < BIG_BUF_SIZE); i++)
- {
- t = &timer_expired_log[(fast_timers_expired - i - 1) % NUM_TIMER_STATS];
- used += sprintf(bigbuf + used, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
- "d: %6li us data: 0x%08lX"
- "\n",
- t->name,
- (unsigned long)t->tv_set.tv_jiff,
- (unsigned long)t->tv_set.tv_usec,
- (unsigned long)t->tv_expires.tv_jiff,
- (unsigned long)t->tv_expires.tv_usec,
- t->delay_us,
- t->data
- );
- }
- used += sprintf(bigbuf + used, "\n");
+ num_to_show = (fast_timers_added < NUM_TIMER_STATS ? fast_timers_added:
+ NUM_TIMER_STATS);
+ seq_printf(m, "Timers added: %i\n", fast_timers_added);
+ for (i = 0; i < num_to_show; i++) {
+ t = &timer_added_log[(fast_timers_added - i - 1) % NUM_TIMER_STATS];
+ if (seq_printf(m, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
+ "d: %6li us data: 0x%08lX"
+ "\n",
+ t->name,
+ (unsigned long)t->tv_set.tv_jiff,
+ (unsigned long)t->tv_set.tv_usec,
+ (unsigned long)t->tv_expires.tv_jiff,
+ (unsigned long)t->tv_expires.tv_usec,
+ t->delay_us,
+ t->data) < 0)
+ return 0;
+ }
+ seq_putc(m, '\n');
+
+ num_to_show = (fast_timers_expired < NUM_TIMER_STATS ? fast_timers_expired:
+ NUM_TIMER_STATS);
+ seq_printf(m, "Timers expired: %i\n", fast_timers_expired);
+ for (i = 0; i < num_to_show; i++){
+ t = &timer_expired_log[(fast_timers_expired - i - 1) % NUM_TIMER_STATS];
+ if (seq_printf(m, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
+ "d: %6li us data: 0x%08lX"
+ "\n",
+ t->name,
+ (unsigned long)t->tv_set.tv_jiff,
+ (unsigned long)t->tv_set.tv_usec,
+ (unsigned long)t->tv_expires.tv_jiff,
+ (unsigned long)t->tv_expires.tv_usec,
+ t->delay_us,
+ t->data) < 0)
+ return 0;
+ }
+ seq_putc(m, '\n');
#endif
- used += sprintf(bigbuf + used, "Active timers:\n");
- local_irq_save(flags);
- t = fast_timer_list;
- while (t != NULL && (used+100 < BIG_BUF_SIZE))
- {
- nextt = t->next;
- local_irq_restore(flags);
- used += sprintf(bigbuf + used, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
- "d: %6li us data: 0x%08lX"
+ seq_puts(m, "Active timers:\n");
+ local_irq_save(flags);
+ t = fast_timer_list;
+ while (t != NULL){
+ nextt = t->next;
+ local_irq_restore(flags);
+ if (seq_printf(m, "%-14s s: %6lu.%06lu e: %6lu.%06lu "
+ "d: %6li us data: 0x%08lX"
/* " func: 0x%08lX" */
- "\n",
- t->name,
- (unsigned long)t->tv_set.tv_jiff,
- (unsigned long)t->tv_set.tv_usec,
- (unsigned long)t->tv_expires.tv_jiff,
- (unsigned long)t->tv_expires.tv_usec,
- t->delay_us,
- t->data
+ "\n",
+ t->name,
+ (unsigned long)t->tv_set.tv_jiff,
+ (unsigned long)t->tv_set.tv_usec,
+ (unsigned long)t->tv_expires.tv_jiff,
+ (unsigned long)t->tv_expires.tv_usec,
+ t->delay_us,
+ t->data
/* , t->function */
- );
- local_irq_save(flags);
- if (t->next != nextt)
- {
- printk("timer removed!\n");
- }
- t = nextt;
- }
- local_irq_restore(flags);
- }
+ ) < 0)
+ return 0;
+ local_irq_save(flags);
+ if (t->next != nextt)
+ printk("timer removed!\n");
+ t = nextt;
+ }
+ local_irq_restore(flags);
+ return 0;
+}
- if (used - offset < len)
- {
- len = used - offset;
- }
+static int proc_fasttimer_open(struct inode *inode, struct file *file)
+{
+ return single_open_size(file, proc_fasttimer_show, PDE_DATA(inode), BIG_BUF_SIZE);
+}
- memcpy(buf, bigbuf + offset, len);
- *start = buf;
- *eof = 1;
+static const struct file_operations proc_fasttimer_fops = {
+ .open = proc_fasttimer_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
- return len;
-}
#endif /* PROC_FS */
#ifdef FAST_TIMER_TEST
@@ -816,12 +783,10 @@ int fast_timer_init(void)
printk("fast_timer_init()\n");
#ifdef CONFIG_PROC_FS
- fasttimer_proc_entry = create_proc_entry("fasttimer", 0, 0);
- if (fasttimer_proc_entry)
- fasttimer_proc_entry->read_proc = proc_fasttimer_read;
+ proc_create("fasttimer", 0, NULL, &proc_fasttimer_fops);
#endif /* PROC_FS */
if (request_irq(TIMER0_INTR_VECT, timer_trig_interrupt,
- IRQF_SHARED | IRQF_DISABLED,
+ IRQF_SHARED,
"fast timer int", &fast_timer_list))
printk(KERN_ERR "err: fasttimer irq\n");
fast_timer_is_init = 1;
diff --git a/arch/cris/arch-v32/kernel/irq.c b/arch/cris/arch-v32/kernel/irq.c
index 5ebe6e84182..25437ae2812 100644
--- a/arch/cris/arch-v32/kernel/irq.c
+++ b/arch/cris/arch-v32/kernel/irq.c
@@ -331,11 +331,11 @@ extern void do_IRQ(int irq, struct pt_regs * regs);
void
crisv32_do_IRQ(int irq, int block, struct pt_regs* regs)
{
- /* Interrupts that may not be moved to another CPU and
- * are IRQF_DISABLED may skip blocking. This is currently
- * only valid for the timer IRQ and the IPI and is used
- * for the timer interrupt to avoid watchdog starvation.
- */
+ /* Interrupts that may not be moved to another CPU may
+ * skip blocking. This is currently only valid for the
+ * timer IRQ and the IPI and is used for the timer
+ * interrupt to avoid watchdog starvation.
+ */
if (!block) {
do_IRQ(irq, regs);
return;
diff --git a/arch/cris/arch-v32/kernel/process.c b/arch/cris/arch-v32/kernel/process.c
index 2b23ef0e445..cebd32e2a8f 100644
--- a/arch/cris/arch-v32/kernel/process.c
+++ b/arch/cris/arch-v32/kernel/process.c
@@ -20,18 +20,12 @@
extern void stop_watchdog(void);
-extern int cris_hlt_counter;
-
/* We use this if we don't have any better idle routine. */
void default_idle(void)
{
- local_irq_disable();
- if (!need_resched() && !cris_hlt_counter) {
- /* Halt until exception. */
- __asm__ volatile("ei \n\t"
- "halt ");
- }
- local_irq_enable();
+ /* Halt until exception. */
+ __asm__ volatile("ei \n\t"
+ "halt ");
}
/*
@@ -170,6 +164,9 @@ get_wchan(struct task_struct *p)
void show_regs(struct pt_regs * regs)
{
unsigned long usp = rdusp();
+
+ show_regs_print_info(KERN_DEFAULT);
+
printk("ERP: %08lx SRP: %08lx CCS: %08lx USP: %08lx MOF: %08lx\n",
regs->erp, regs->srp, regs->ccs, usp, regs->mof);
diff --git a/arch/cris/arch-v32/kernel/smp.c b/arch/cris/arch-v32/kernel/smp.c
index 04a16edd540..0698582467c 100644
--- a/arch/cris/arch-v32/kernel/smp.c
+++ b/arch/cris/arch-v32/kernel/smp.c
@@ -64,7 +64,7 @@ static irqreturn_t crisv32_ipi_interrupt(int irq, void *dev_id);
static int send_ipi(int vector, int wait, cpumask_t cpu_mask);
static struct irqaction irq_ipi = {
.handler = crisv32_ipi_interrupt,
- .flags = IRQF_DISABLED,
+ .flags = 0,
.name = "ipi",
};
@@ -145,8 +145,6 @@ smp_boot_one_cpu(int cpuid, struct task_struct idle)
* specific stuff such as the local timer and the MMU. */
void __init smp_callin(void)
{
- extern void cpu_idle(void);
-
int cpu = cpu_now_booting;
reg_intr_vect_rw_mask vect_mask = {0};
@@ -170,7 +168,7 @@ void __init smp_callin(void)
local_irq_enable();
set_cpu_online(cpu, true);
- cpu_idle();
+ cpu_startup_entry(CPUHP_ONLINE);
}
/* Stop execution on this CPU.*/
@@ -199,7 +197,7 @@ int setup_profiling_timer(unsigned int multiplier)
*/
unsigned long cache_decay_ticks = 1;
-int __cpuinit __cpu_up(unsigned int cpu, struct task_struct *tidle)
+int __cpu_up(unsigned int cpu, struct task_struct *tidle)
{
smp_boot_one_cpu(cpu, tidle);
return cpu_online(cpu) ? 0 : -ENOSYS;
diff --git a/arch/cris/arch-v32/kernel/time.c b/arch/cris/arch-v32/kernel/time.c
index 8c4b45efd7b..ee66866538f 100644
--- a/arch/cris/arch-v32/kernel/time.c
+++ b/arch/cris/arch-v32/kernel/time.c
@@ -216,12 +216,10 @@ static inline irqreturn_t timer_interrupt(int irq, void *dev_id)
return IRQ_HANDLED;
}
-/* Timer is IRQF_SHARED so drivers can add stuff to the timer irq chain.
- * It needs to be IRQF_DISABLED to make the jiffies update work properly.
- */
+/* Timer is IRQF_SHARED so drivers can add stuff to the timer irq chain. */
static struct irqaction irq_timer = {
.handler = timer_interrupt,
- .flags = IRQF_SHARED | IRQF_DISABLED,
+ .flags = IRQF_SHARED,
.name = "timer"
};
diff --git a/arch/cris/arch-v32/mach-a3/Kconfig b/arch/cris/arch-v32/mach-a3/Kconfig
index 7796aafc711..87547271a59 100644
--- a/arch/cris/arch-v32/mach-a3/Kconfig
+++ b/arch/cris/arch-v32/mach-a3/Kconfig
@@ -15,10 +15,6 @@ config ETRAX_SERIAL_PORTS
int
default 5
-config ETRAX_DDR
- bool
- default y
-
config ETRAX_DDR2_MRS
hex "DDR2 MRS"
default "0"
diff --git a/arch/cris/arch-v32/mach-a3/Makefile b/arch/cris/arch-v32/mach-a3/Makefile
index d366e089198..18a227196a4 100644
--- a/arch/cris/arch-v32/mach-a3/Makefile
+++ b/arch/cris/arch-v32/mach-a3/Makefile
@@ -3,7 +3,6 @@
#
obj-y := dma.o pinmux.o io.o arbiter.o
-obj-$(CONFIG_CPU_FREQ) += cpufreq.o
clean:
diff --git a/arch/cris/arch-v32/mach-a3/arbiter.c b/arch/cris/arch-v32/mach-a3/arbiter.c
index 15f5c9de263..ab5c421a4de 100644
--- a/arch/cris/arch-v32/mach-a3/arbiter.c
+++ b/arch/cris/arch-v32/mach-a3/arbiter.c
@@ -256,11 +256,11 @@ static void crisv32_arbiter_init(void)
crisv32_arbiter_config(1, EXT_REGION, 0);
if (request_irq(MEMARB_FOO_INTR_VECT, crisv32_foo_arbiter_irq,
- IRQF_DISABLED, "arbiter", NULL))
+ 0, "arbiter", NULL))
printk(KERN_ERR "Couldn't allocate arbiter IRQ\n");
if (request_irq(MEMARB_BAR_INTR_VECT, crisv32_bar_arbiter_irq,
- IRQF_DISABLED, "arbiter", NULL))
+ 0, "arbiter", NULL))
printk(KERN_ERR "Couldn't allocate arbiter IRQ\n");
#ifndef CONFIG_ETRAX_KGDB
diff --git a/arch/cris/arch-v32/mach-a3/cpufreq.c b/arch/cris/arch-v32/mach-a3/cpufreq.c
deleted file mode 100644
index ee391ecb5bc..00000000000
--- a/arch/cris/arch-v32/mach-a3/cpufreq.c
+++ /dev/null
@@ -1,152 +0,0 @@
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/cpufreq.h>
-#include <hwregs/reg_map.h>
-#include <hwregs/reg_rdwr.h>
-#include <hwregs/clkgen_defs.h>
-#include <hwregs/ddr2_defs.h>
-
-static int
-cris_sdram_freq_notifier(struct notifier_block *nb, unsigned long val,
- void *data);
-
-static struct notifier_block cris_sdram_freq_notifier_block = {
- .notifier_call = cris_sdram_freq_notifier
-};
-
-static struct cpufreq_frequency_table cris_freq_table[] = {
- {0x01, 6000},
- {0x02, 200000},
- {0, CPUFREQ_TABLE_END},
-};
-
-static unsigned int cris_freq_get_cpu_frequency(unsigned int cpu)
-{
- reg_clkgen_rw_clk_ctrl clk_ctrl;
- clk_ctrl = REG_RD(clkgen, regi_clkgen, rw_clk_ctrl);
- return clk_ctrl.pll ? 200000 : 6000;
-}
-
-static void cris_freq_set_cpu_state(unsigned int state)
-{
- int i = 0;
- struct cpufreq_freqs freqs;
- reg_clkgen_rw_clk_ctrl clk_ctrl;
- clk_ctrl = REG_RD(clkgen, regi_clkgen, rw_clk_ctrl);
-
-#ifdef CONFIG_SMP
- for_each_present_cpu(i)
-#endif
- {
- freqs.old = cris_freq_get_cpu_frequency(i);
- freqs.new = cris_freq_table[state].frequency;
- freqs.cpu = i;
- }
-
- cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
-
- local_irq_disable();
-
- /* Even though we may be SMP they will share the same clock
- * so all settings are made on CPU0. */
- if (cris_freq_table[state].frequency == 200000)
- clk_ctrl.pll = 1;
- else
- clk_ctrl.pll = 0;
- REG_WR(clkgen, regi_clkgen, rw_clk_ctrl, clk_ctrl);
-
- local_irq_enable();
-
- cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
-};
-
-static int cris_freq_verify(struct cpufreq_policy *policy)
-{
- return cpufreq_frequency_table_verify(policy, &cris_freq_table[0]);
-}
-
-static int cris_freq_target(struct cpufreq_policy *policy,
- unsigned int target_freq,
- unsigned int relation)
-{
- unsigned int newstate = 0;
-
- if (cpufreq_frequency_table_target(policy, cris_freq_table,
- target_freq, relation, &newstate))
- return -EINVAL;
-
- cris_freq_set_cpu_state(newstate);
-
- return 0;
-}
-
-static int cris_freq_cpu_init(struct cpufreq_policy *policy)
-{
- int result;
-
- /* cpuinfo and default policy values */
- policy->cpuinfo.transition_latency = 1000000; /* 1ms */
- policy->cur = cris_freq_get_cpu_frequency(0);
-
- result = cpufreq_frequency_table_cpuinfo(policy, cris_freq_table);
- if (result)
- return (result);
-
- cpufreq_frequency_table_get_attr(cris_freq_table, policy->cpu);
-
- return 0;
-}
-
-
-static int cris_freq_cpu_exit(struct cpufreq_policy *policy)
-{
- cpufreq_frequency_table_put_attr(policy->cpu);
- return 0;
-}
-
-
-static struct freq_attr *cris_freq_attr[] = {
- &cpufreq_freq_attr_scaling_available_freqs,
- NULL,
-};
-
-static struct cpufreq_driver cris_freq_driver = {
- .get = cris_freq_get_cpu_frequency,
- .verify = cris_freq_verify,
- .target = cris_freq_target,
- .init = cris_freq_cpu_init,
- .exit = cris_freq_cpu_exit,
- .name = "cris_freq",
- .owner = THIS_MODULE,
- .attr = cris_freq_attr,
-};
-
-static int __init cris_freq_init(void)
-{
- int ret;
- ret = cpufreq_register_driver(&cris_freq_driver);
- cpufreq_register_notifier(&cris_sdram_freq_notifier_block,
- CPUFREQ_TRANSITION_NOTIFIER);
- return ret;
-}
-
-static int
-cris_sdram_freq_notifier(struct notifier_block *nb, unsigned long val,
- void *data)
-{
- int i;
- struct cpufreq_freqs *freqs = data;
- if (val == CPUFREQ_PRECHANGE) {
- reg_ddr2_rw_cfg cfg =
- REG_RD(ddr2, regi_ddr2_ctrl, rw_cfg);
- cfg.ref_interval = (freqs->new == 200000 ? 1560 : 46);
-
- if (freqs->new == 200000)
- for (i = 0; i < 50000; i++);
- REG_WR(bif_core, regi_bif_core, rw_sdram_timing, timing);
- }
- return 0;
-}
-
-
-module_init(cris_freq_init);
diff --git a/arch/cris/arch-v32/mach-fs/Makefile b/arch/cris/arch-v32/mach-fs/Makefile
index d366e089198..18a227196a4 100644
--- a/arch/cris/arch-v32/mach-fs/Makefile
+++ b/arch/cris/arch-v32/mach-fs/Makefile
@@ -3,7 +3,6 @@
#
obj-y := dma.o pinmux.o io.o arbiter.o
-obj-$(CONFIG_CPU_FREQ) += cpufreq.o
clean:
diff --git a/arch/cris/arch-v32/mach-fs/arbiter.c b/arch/cris/arch-v32/mach-fs/arbiter.c
index 3f8ebb5c147..c97f4d8120f 100644
--- a/arch/cris/arch-v32/mach-fs/arbiter.c
+++ b/arch/cris/arch-v32/mach-fs/arbiter.c
@@ -184,7 +184,7 @@ static void crisv32_arbiter_init(void)
crisv32_arbiter_config(EXT_REGION, 0);
crisv32_arbiter_config(INT_REGION, 0);
- if (request_irq(MEMARB_INTR_VECT, crisv32_arbiter_irq, IRQF_DISABLED,
+ if (request_irq(MEMARB_INTR_VECT, crisv32_arbiter_irq, 0,
"arbiter", NULL))
printk(KERN_ERR "Couldn't allocate arbiter IRQ\n");
diff --git a/arch/cris/arch-v32/mach-fs/cpufreq.c b/arch/cris/arch-v32/mach-fs/cpufreq.c
deleted file mode 100644
index d92cf70d1cb..00000000000
--- a/arch/cris/arch-v32/mach-fs/cpufreq.c
+++ /dev/null
@@ -1,145 +0,0 @@
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/cpufreq.h>
-#include <hwregs/reg_map.h>
-#include <arch/hwregs/reg_rdwr.h>
-#include <arch/hwregs/config_defs.h>
-#include <arch/hwregs/bif_core_defs.h>
-
-static int
-cris_sdram_freq_notifier(struct notifier_block *nb, unsigned long val,
- void *data);
-
-static struct notifier_block cris_sdram_freq_notifier_block = {
- .notifier_call = cris_sdram_freq_notifier
-};
-
-static struct cpufreq_frequency_table cris_freq_table[] = {
- {0x01, 6000},
- {0x02, 200000},
- {0, CPUFREQ_TABLE_END},
-};
-
-static unsigned int cris_freq_get_cpu_frequency(unsigned int cpu)
-{
- reg_config_rw_clk_ctrl clk_ctrl;
- clk_ctrl = REG_RD(config, regi_config, rw_clk_ctrl);
- return clk_ctrl.pll ? 200000 : 6000;
-}
-
-static void cris_freq_set_cpu_state(unsigned int state)
-{
- int i;
- struct cpufreq_freqs freqs;
- reg_config_rw_clk_ctrl clk_ctrl;
- clk_ctrl = REG_RD(config, regi_config, rw_clk_ctrl);
-
- for_each_possible_cpu(i) {
- freqs.old = cris_freq_get_cpu_frequency(i);
- freqs.new = cris_freq_table[state].frequency;
- freqs.cpu = i;
- }
-
- cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
-
- local_irq_disable();
-
- /* Even though we may be SMP they will share the same clock
- * so all settings are made on CPU0. */
- if (cris_freq_table[state].frequency == 200000)
- clk_ctrl.pll = 1;
- else
- clk_ctrl.pll = 0;
- REG_WR(config, regi_config, rw_clk_ctrl, clk_ctrl);
-
- local_irq_enable();
-
- cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
-};
-
-static int cris_freq_verify(struct cpufreq_policy *policy)
-{
- return cpufreq_frequency_table_verify(policy, &cris_freq_table[0]);
-}
-
-static int cris_freq_target(struct cpufreq_policy *policy,
- unsigned int target_freq, unsigned int relation)
-{
- unsigned int newstate = 0;
-
- if (cpufreq_frequency_table_target
- (policy, cris_freq_table, target_freq, relation, &newstate))
- return -EINVAL;
-
- cris_freq_set_cpu_state(newstate);
-
- return 0;
-}
-
-static int cris_freq_cpu_init(struct cpufreq_policy *policy)
-{
- int result;
-
- /* cpuinfo and default policy values */
- policy->cpuinfo.transition_latency = 1000000; /* 1ms */
- policy->cur = cris_freq_get_cpu_frequency(0);
-
- result = cpufreq_frequency_table_cpuinfo(policy, cris_freq_table);
- if (result)
- return (result);
-
- cpufreq_frequency_table_get_attr(cris_freq_table, policy->cpu);
-
- return 0;
-}
-
-static int cris_freq_cpu_exit(struct cpufreq_policy *policy)
-{
- cpufreq_frequency_table_put_attr(policy->cpu);
- return 0;
-}
-
-static struct freq_attr *cris_freq_attr[] = {
- &cpufreq_freq_attr_scaling_available_freqs,
- NULL,
-};
-
-static struct cpufreq_driver cris_freq_driver = {
- .get = cris_freq_get_cpu_frequency,
- .verify = cris_freq_verify,
- .target = cris_freq_target,
- .init = cris_freq_cpu_init,
- .exit = cris_freq_cpu_exit,
- .name = "cris_freq",
- .owner = THIS_MODULE,
- .attr = cris_freq_attr,
-};
-
-static int __init cris_freq_init(void)
-{
- int ret;
- ret = cpufreq_register_driver(&cris_freq_driver);
- cpufreq_register_notifier(&cris_sdram_freq_notifier_block,
- CPUFREQ_TRANSITION_NOTIFIER);
- return ret;
-}
-
-static int
-cris_sdram_freq_notifier(struct notifier_block *nb, unsigned long val,
- void *data)
-{
- int i;
- struct cpufreq_freqs *freqs = data;
- if (val == CPUFREQ_PRECHANGE) {
- reg_bif_core_rw_sdram_timing timing =
- REG_RD(bif_core, regi_bif_core, rw_sdram_timing);
- timing.cpd = (freqs->new == 200000 ? 0 : 1);
-
- if (freqs->new == 200000)
- for (i = 0; i < 50000; i++) ;
- REG_WR(bif_core, regi_bif_core, rw_sdram_timing, timing);
- }
- return 0;
-}
-
-module_init(cris_freq_init);
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-12-15 20:47:43 +0000