aboutsummaryrefslogtreecommitdiff
path: root/arch/cris/arch-v10/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'arch/cris/arch-v10/drivers')
-rw-r--r--arch/cris/arch-v10/drivers/Kconfig70
-rw-r--r--arch/cris/arch-v10/drivers/Makefile2
-rw-r--r--arch/cris/arch-v10/drivers/gpio.c8
-rw-r--r--arch/cris/arch-v10/drivers/sync_serial.c8
4 files changed, 9 insertions, 79 deletions
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index daf5f19b61a..239dab0b95c 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -417,16 +417,6 @@ config ETRAX_USB_HOST
for CTRL and BULK traffic only, INTR traffic may work as well
however (depending on the requirements of timeliness).
-config ETRAX_USB_HOST_PORT1
- bool "USB port 1 enabled"
- depends on ETRAX_USB_HOST
- default n
-
-config ETRAX_USB_HOST_PORT2
- bool "USB port 2 enabled"
- depends on ETRAX_USB_HOST
- default n
-
config ETRAX_PTABLE_SECTOR
int "Byte-offset of partition table sector"
depends on ETRAX_AXISFLASHMAP
@@ -527,19 +517,6 @@ config ETRAX_GPIO
Remember that you need to setup the port directions appropriately in
the General configuration.
-config ETRAX_PA_BUTTON_BITMASK
- hex "PA-buttons bitmask"
- depends on ETRAX_GPIO
- default "02"
- help
- This is a bitmask with information about what bits on PA that
- are used for buttons.
- Most products has a so called TEST button on PA1, if that's true
- use 02 here.
- Use 00 if there are no buttons on PA.
- If the bitmask is <> 00 a button driver will be included in the gpio
- driver. ETRAX general I/O support must be enabled.
-
config ETRAX_PA_CHANGEABLE_DIR
hex "PA user changeable dir mask"
depends on ETRAX_GPIO
@@ -580,51 +557,4 @@ config ETRAX_PB_CHANGEABLE_BITS
Bit set = changeable.
You probably want 00 here.
-config ETRAX_DS1302_RST_ON_GENERIC_PORT
- bool "DS1302 RST on Generic Port"
- depends on ETRAX_DS1302
- help
- If your product has the RST signal line for the DS1302 RTC on the
- Generic Port then say Y here, otherwise leave it as N in which
- case the RST signal line is assumed to be connected to Port PB
- (just like the SCL and SDA lines).
-
-config ETRAX_DS1302_RSTBIT
- int "DS1302 RST bit number"
- depends on ETRAX_DS1302
- default "2"
- help
- This is the bit number for the RST signal line of the DS1302 RTC on
- the selected port. If you have selected the generic port then it
- should be bit 27, otherwise your best bet is bit 5.
-
-config ETRAX_DS1302_SCLBIT
- int "DS1302 SCL bit number"
- depends on ETRAX_DS1302
- default "1"
- help
- This is the bit number for the SCL signal line of the DS1302 RTC on
- Port PB. This is probably best left at 3.
-
-config ETRAX_DS1302_SDABIT
- int "DS1302 SDA bit number"
- depends on ETRAX_DS1302
- default "0"
- help
- This is the bit number for the SDA signal line of the DS1302 RTC on
- Port PB. This is probably best left at 2.
-
-config ETRAX_DS1302_TRICKLE_CHARGE
- int "DS1302 Trickle charger value"
- depends on ETRAX_DS1302
- default "0"
- help
- This controls the initial value of the trickle charge register.
- 0 = disabled (use this if you are unsure or have a non rechargeable battery)
- Otherwise the following values can be OR:ed together to control the
- charge current:
- 1 = 2kohm, 2 = 4kohm, 3 = 4kohm
- 4 = 1 diode, 8 = 2 diodes
- Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5
-
endif
diff --git a/arch/cris/arch-v10/drivers/Makefile b/arch/cris/arch-v10/drivers/Makefile
index 44bf2e88c26..e5c13183b97 100644
--- a/arch/cris/arch-v10/drivers/Makefile
+++ b/arch/cris/arch-v10/drivers/Makefile
@@ -6,7 +6,5 @@ obj-$(CONFIG_ETRAX_AXISFLASHMAP) += axisflashmap.o
obj-$(CONFIG_ETRAX_I2C) += i2c.o
obj-$(CONFIG_ETRAX_I2C_EEPROM) += eeprom.o
obj-$(CONFIG_ETRAX_GPIO) += gpio.o
-obj-$(CONFIG_ETRAX_DS1302) += ds1302.o
-obj-$(CONFIG_ETRAX_PCF8563) += pcf8563.o
obj-$(CONFIG_ETRAX_SYNCHRONOUS_SERIAL) += sync_serial.o
diff --git a/arch/cris/arch-v10/drivers/gpio.c b/arch/cris/arch-v10/drivers/gpio.c
index 609d5510410..64285e0d348 100644
--- a/arch/cris/arch-v10/drivers/gpio.c
+++ b/arch/cris/arch-v10/drivers/gpio.c
@@ -833,18 +833,18 @@ static int __init gpio_init(void)
printk(KERN_INFO "ETRAX 100LX GPIO driver v2.5, (c) 2001-2008 "
"Axis Communications AB\n");
/* We call etrax_gpio_wake_up_check() from timer interrupt and
- * from cpu_idle() in kernel/process.c
- * The check in cpu_idle() reduces latency from ~15 ms to ~6 ms
+ * from default_idle() in kernel/process.c
+ * The check in default_idle() reduces latency from ~15 ms to ~6 ms
* in some tests.
*/
res = request_irq(TIMER0_IRQ_NBR, gpio_poll_timer_interrupt,
- IRQF_SHARED | IRQF_DISABLED, "gpio poll", gpio_name);
+ IRQF_SHARED, "gpio poll", gpio_name);
if (res) {
printk(KERN_CRIT "err: timer0 irq for gpio\n");
return res;
}
res = request_irq(PA_IRQ_NBR, gpio_interrupt,
- IRQF_SHARED | IRQF_DISABLED, "gpio PA", gpio_name);
+ IRQF_SHARED, "gpio PA", gpio_name);
if (res)
printk(KERN_CRIT "err: PA irq for gpio\n");
diff --git a/arch/cris/arch-v10/drivers/sync_serial.c b/arch/cris/arch-v10/drivers/sync_serial.c
index a1c498d18d3..29eb02ab3f2 100644
--- a/arch/cris/arch-v10/drivers/sync_serial.c
+++ b/arch/cris/arch-v10/drivers/sync_serial.c
@@ -22,6 +22,7 @@
#include <linux/init.h>
#include <linux/mutex.h>
#include <linux/timer.h>
+#include <linux/wait.h>
#include <asm/irq.h>
#include <asm/dma.h>
#include <asm/io.h>
@@ -580,7 +581,7 @@ static int sync_serial_open(struct inode *inode, struct file *file)
if (port == &ports[0]) {
if (request_irq(8,
manual_interrupt,
- IRQF_SHARED | IRQF_DISABLED,
+ IRQF_SHARED,
"synchronous serial manual irq",
&ports[0])) {
printk(KERN_CRIT "Can't alloc "
@@ -590,7 +591,7 @@ static int sync_serial_open(struct inode *inode, struct file *file)
} else if (port == &ports[1]) {
if (request_irq(8,
manual_interrupt,
- IRQF_SHARED | IRQF_DISABLED,
+ IRQF_SHARED,
"synchronous serial manual irq",
&ports[1])) {
printk(KERN_CRIT "Can't alloc "
@@ -1136,7 +1137,8 @@ static ssize_t sync_serial_read(struct file *file, char *buf,
if (file->f_flags & O_NONBLOCK)
return -EAGAIN;
- interruptible_sleep_on(&port->in_wait_q);
+ wait_event_interruptible(port->in_wait_q,
+ !(start == end && !port->full));
if (signal_pending(current))
return -EINTR;
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-11-10 11:40:20 +0000