12 files changed, 2705 insertions, 208 deletions

diff --git a/arch/blackfin/mach-bf609/Kconfig b/arch/blackfin/mach-bf609/Kconfig
index 95a4f1b676c..6584190faeb 100644
--- a/arch/blackfin/mach-bf609/Kconfig
+++ b/arch/blackfin/mach-bf609/Kconfig
@@ -9,48 +9,6 @@ source "arch/blackfin/mach-bf609/boards/Kconfig"
 
 menu "BF609 Specific Configuration"
 
-comment "Pin Interrupt to Port Assignment"
-menu "Assignment"
-
-config PINTx_REASSIGN
-	bool "Reprogram PINT Assignment"
-	default y
-	help
-	  The interrupt assignment registers controls the pin-to-interrupt
-	  assignment in a byte-wide manner. Each option allows you to select
-	  a set of pins (High/Low Byte) of an specific Port being mapped
-	  to one of the four PIN Interrupts IRQ_PINTx.
-
-	  You shouldn't change any of these unless you know exactly what you're doing.
-	  Please consult the Blackfin BF60x Processor Hardware Reference Manual.
-
-config PINT0_ASSIGN
-	hex "PINT0_ASSIGN"
-	depends on PINTx_REASSIGN
-	default 0x00000101
-config PINT1_ASSIGN
-	hex "PINT1_ASSIGN"
-	depends on PINTx_REASSIGN
-	default 0x00000101
-config PINT2_ASSIGN
-	hex "PINT2_ASSIGN"
-	depends on PINTx_REASSIGN
-	default 0x00000101
-config PINT3_ASSIGN
-	hex "PINT3_ASSIGN"
-	depends on PINTx_REASSIGN
-	default 0x00000101
-config PINT4_ASSIGN
-	hex "PINT3_ASSIGN"
-	depends on PINTx_REASSIGN
-	default 0x00000101
-config PINT5_ASSIGN
-	hex "PINT3_ASSIGN"
-	depends on PINTx_REASSIGN
-	default 0x00000101
-
-endmenu
-
 config SEC_IRQ_PRIORITY_LEVELS
 	int "SEC interrupt priority levels"
 	default 7
@@ -59,6 +17,1667 @@ config SEC_IRQ_PRIORITY_LEVELS
 	  Divide the total number of interrupt priority levels into sub-levels.
 	  There is 2 ^ (SEC_IRQ_PRIORITY_LEVELS + 1) different levels.
 
+config L1_PARITY_CHECK
+	bool "Enable L1 parity check"
+	default n
+	help
+	  Enable the L1 parity check in L1 sram. A fault event is raised
+	  when L1 parity error is found.
+
+comment "System Cross Bar Priority Assignment"
+
+config SCB_PRIORITY
+	bool "Init System Cross Bar Priority"
+	default n
+
+menuconfig	SCB0_MI0
+	bool "SCB0 Master Interface 0 (DDR)"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	Core 0	-- 0
+	Core 1	-- 2
+	SCB1	-- 9
+	SCB2	-- 10
+	SCB3	-- 11
+	SCB4	-- 12
+	SCB5	-- 5
+	SCB6	-- 6
+	SCB7	-- 8
+	SCB8	-- 7
+	SCB9	-- 4
+	USB	-- 13
+
+if SCB0_MI0
+
+config SCB0_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 13
+
+config SCB0_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 2
+	range 0 13
+
+config SCB0_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI0_SLOT8
+	int "Slot 8 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI0_SLOT9
+	int "Slot 9 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI0_SLOT10
+	int "Slot 10 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI0_SLOT11
+	int "Slot 11 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI0_SLOT12
+	int "Slot 12 slave interface id"
+	default 0
+	range 0 13
+
+config SCB0_MI0_SLOT13
+	int "Slot 13 slave interface id"
+	default 2
+	range 0 13
+
+config SCB0_MI0_SLOT14
+	int "Slot 14 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI0_SLOT15
+	int "Slot 15 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI0_SLOT16
+	int "Slot 16 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI0_SLOT17
+	int "Slot 17 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI0_SLOT18
+	int "Slot 18 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI0_SLOT19
+	int "Slot 19 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI0_SLOT20
+	int "Slot 20 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI0_SLOT21
+	int "Slot 21 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI0_SLOT22
+	int "Slot 22 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI0_SLOT23
+	int "Slot 23 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI0_SLOT24
+	int "Slot 24 slave interface id"
+	default 0
+	range 0 13
+
+config SCB0_MI0_SLOT25
+	int "Slot 25 slave interface id"
+	default 2
+	range 0 13
+
+config SCB0_MI0_SLOT26
+	int "Slot 26 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI0_SLOT27
+	int "Slot 27 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI0_SLOT28
+	int "Slot 28 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI0_SLOT29
+	int "Slot 29 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI0_SLOT30
+	int "Slot 30 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI0_SLOT31
+	int "Slot 31 slave interface id"
+	default 13
+	range 0 13
+
+endif # SCB0_MI0
+
+menuconfig	SCB0_MI1
+	bool "SCB0 Master Interface 1 (SMC)"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	Core 0	-- 0
+	Core 1	-- 2
+	SCB1	-- 9
+	SCB2	-- 10
+	SCB3	-- 11
+	SCB4	-- 12
+	SCB5	-- 5
+	SCB6	-- 6
+	SCB7	-- 8
+	SCB8	-- 7
+	SCB9	-- 4
+	USB	-- 13
+
+if SCB0_MI1
+
+config SCB0_MI1_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 13
+
+config SCB0_MI1_SLOT1
+	int "Slot 1 slave interface id"
+	default 2
+	range 0 13
+
+config SCB0_MI1_SLOT2
+	int "Slot 2 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI1_SLOT3
+	int "Slot 3 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI1_SLOT4
+	int "Slot 4 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI1_SLOT5
+	int "Slot 5 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI1_SLOT6
+	int "Slot 6 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI1_SLOT7
+	int "Slot 7 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI1_SLOT8
+	int "Slot 8 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI1_SLOT9
+	int "Slot 9 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI1_SLOT10
+	int "Slot 10 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI1_SLOT11
+	int "Slot 11 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI1_SLOT12
+	int "Slot 12 slave interface id"
+	default 0
+	range 0 13
+
+config SCB0_MI1_SLOT13
+	int "Slot 13 slave interface id"
+	default 2
+	range 0 13
+
+config SCB0_MI1_SLOT14
+	int "Slot 14 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI1_SLOT15
+	int "Slot 15 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI1_SLOT16
+	int "Slot 16 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI1_SLOT17
+	int "Slot 17 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI1_SLOT18
+	int "Slot 18 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI1_SLOT19
+	int "Slot 19 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI1_SLOT20
+	int "Slot 20 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI1_SLOT21
+	int "Slot 21 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI1_SLOT22
+	int "Slot 22 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI1_SLOT23
+	int "Slot 23 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI1_SLOT24
+	int "Slot 24 slave interface id"
+	default 0
+	range 0 13
+
+config SCB0_MI1_SLOT25
+	int "Slot 25 slave interface id"
+	default 2
+	range 0 13
+
+config SCB0_MI1_SLOT26
+	int "Slot 26 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI1_SLOT27
+	int "Slot 27 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI1_SLOT28
+	int "Slot 28 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI1_SLOT29
+	int "Slot 29 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI1_SLOT30
+	int "Slot 30 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI1_SLOT31
+	int "Slot 31 slave interface id"
+	default 13
+	range 0 13
+
+endif # SCB0_MI1
+
+menuconfig	SCB0_MI2
+	bool "SCB0 Master Interface 2 (Data L2)"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	Core 0	-- 0
+	Core 1	-- 2
+	SCB1	-- 9
+	SCB2	-- 10
+	SCB3	-- 11
+	SCB4	-- 12
+	SCB5	-- 5
+	SCB6	-- 6
+	SCB7	-- 8
+	SCB8	-- 7
+	SCB9	-- 4
+	USB	-- 13
+
+if SCB0_MI2
+
+config SCB0_MI2_SLOT0
+	int "Slot 0 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI2_SLOT1
+	int "Slot 1 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI2_SLOT2
+	int "Slot 2 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI2_SLOT3
+	int "Slot 3 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI2_SLOT4
+	int "Slot 4 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI2_SLOT5
+	int "Slot 5 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI2_SLOT6
+	int "Slot 6 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI2_SLOT7
+	int "Slot 7 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI2_SLOT8
+	int "Slot 8 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI2_SLOT9
+	int "Slot 9 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI2_SLOT10
+	int "Slot 10 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI2_SLOT11
+	int "Slot 11 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI2_SLOT12
+	int "Slot 12 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI2_SLOT13
+	int "Slot 13 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI2_SLOT14
+	int "Slot 14 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI2_SLOT15
+	int "Slot 15 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI2_SLOT16
+	int "Slot 16 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI2_SLOT17
+	int "Slot 17 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI2_SLOT18
+	int "Slot 18 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI2_SLOT19
+	int "Slot 19 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI2_SLOT20
+	int "Slot 20 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI2_SLOT21
+	int "Slot 21 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI2_SLOT22
+	int "Slot 22 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI2_SLOT23
+	int "Slot 23 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI2_SLOT24
+	int "Slot 24 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI2_SLOT25
+	int "Slot 25 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI2_SLOT26
+	int "Slot 26 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI2_SLOT27
+	int "Slot 27 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI2_SLOT28
+	int "Slot 28 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI2_SLOT29
+	int "Slot 29 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI2_SLOT30
+	int "Slot 30 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI2_SLOT31
+	int "Slot 31 slave interface id"
+	default 7
+	range 0 13
+
+endif # SCB0_MI2
+
+menuconfig	SCB0_MI3
+	bool "SCB0 Master Interface 3 (L1A)"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	Core 0	-- 0
+	Core 1	-- 2
+	SCB1	-- 9
+	SCB2	-- 10
+	SCB3	-- 11
+	SCB4	-- 12
+	SCB5	-- 5
+	SCB6	-- 6
+	SCB7	-- 8
+	SCB8	-- 7
+	SCB9	-- 4
+	USB	-- 13
+
+if SCB0_MI3
+
+config SCB0_MI3_SLOT0
+	int "Slot 0 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI3_SLOT1
+	int "Slot 1 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI3_SLOT2
+	int "Slot 2 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI3_SLOT3
+	int "Slot 3 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI3_SLOT4
+	int "Slot 4 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI3_SLOT5
+	int "Slot 5 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI3_SLOT6
+	int "Slot 6 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI3_SLOT7
+	int "Slot 7 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI3_SLOT8
+	int "Slot 8 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI3_SLOT9
+	int "Slot 9 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI3_SLOT10
+	int "Slot 10 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI3_SLOT11
+	int "Slot 11 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI3_SLOT12
+	int "Slot 12 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI3_SLOT13
+	int "Slot 13 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI3_SLOT14
+	int "Slot 14 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI3_SLOT15
+	int "Slot 15 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI3_SLOT16
+	int "Slot 16 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI3_SLOT17
+	int "Slot 17 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI3_SLOT18
+	int "Slot 18 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI3_SLOT19
+	int "Slot 19 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI3_SLOT20
+	int "Slot 20 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI3_SLOT21
+	int "Slot 21 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI3_SLOT22
+	int "Slot 22 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI3_SLOT23
+	int "Slot 23 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI3_SLOT24
+	int "Slot 24 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI3_SLOT25
+	int "Slot 25 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI3_SLOT26
+	int "Slot 26 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI3_SLOT27
+	int "Slot 27 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI3_SLOT28
+	int "Slot 28 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI3_SLOT29
+	int "Slot 29 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI3_SLOT30
+	int "Slot 30 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI3_SLOT31
+	int "Slot 31 slave interface id"
+	default 7
+	range 0 13
+
+endif # SCB0_MI3
+
+menuconfig	SCB0_MI4
+	bool "SCB0 Master Interface 4 (L1B)"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	Core 0	-- 0
+	Core 1	-- 2
+	SCB1	-- 9
+	SCB2	-- 10
+	SCB3	-- 11
+	SCB4	-- 12
+	SCB5	-- 5
+	SCB6	-- 6
+	SCB7	-- 8
+	SCB8	-- 7
+	SCB9	-- 4
+	USB	-- 13
+
+if SCB0_MI4
+
+config SCB0_MI4_SLOT0
+	int "Slot 0 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI4_SLOT1
+	int "Slot 1 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI4_SLOT2
+	int "Slot 2 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI4_SLOT3
+	int "Slot 3 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI4_SLOT4
+	int "Slot 4 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI4_SLOT5
+	int "Slot 5 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI4_SLOT6
+	int "Slot 6 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI4_SLOT7
+	int "Slot 7 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI4_SLOT8
+	int "Slot 8 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI4_SLOT9
+	int "Slot 9 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI4_SLOT10
+	int "Slot 10 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI4_SLOT11
+	int "Slot 11 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI4_SLOT12
+	int "Slot 12 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI4_SLOT13
+	int "Slot 13 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI4_SLOT14
+	int "Slot 14 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI4_SLOT15
+	int "Slot 15 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI4_SLOT16
+	int "Slot 16 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI4_SLOT17
+	int "Slot 17 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI4_SLOT18
+	int "Slot 18 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI4_SLOT19
+	int "Slot 19 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI4_SLOT20
+	int "Slot 20 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI4_SLOT21
+	int "Slot 21 slave interface id"
+	default 5
+	range 0 13
+
+config SCB0_MI4_SLOT22
+	int "Slot 22 slave interface id"
+	default 6
+	range 0 13
+
+config SCB0_MI4_SLOT23
+	int "Slot 23 slave interface id"
+	default 7
+	range 0 13
+
+config SCB0_MI4_SLOT24
+	int "Slot 24 slave interface id"
+	default 8
+	range 0 13
+
+config SCB0_MI4_SLOT25
+	int "Slot 25 slave interface id"
+	default 9
+	range 0 13
+
+config SCB0_MI4_SLOT26
+	int "Slot 26 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI4_SLOT27
+	int "Slot 27 slave interface id"
+	default 11
+	range 0 13
+
+config SCB0_MI4_SLOT28
+	int "Slot 28 slave interface id"
+	default 13
+	range 0 13
+
+config SCB0_MI4_SLOT29
+	int "Slot 29 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI4_SLOT30
+	int "Slot 30 slave interface id"
+	default 4
+	range 0 13
+
+config SCB0_MI4_SLOT31
+	int "Slot 31 slave interface id"
+	default 7
+	range 0 13
+
+endif # SCB0_MI4
+
+menuconfig	SCB0_MI5
+	bool "SCB0 Master Interface 5 (SMMR)"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	MMR0	-- 1
+	MMR1	-- 3
+	SCB2	-- 10
+	SCB4	-- 12
+
+if SCB0_MI5
+
+config SCB0_MI5_SLOT0
+	int "Slot 0 slave interface id"
+	default 1
+	range 0 13
+
+config SCB0_MI5_SLOT1
+	int "Slot 1 slave interface id"
+	default 3
+	range 0 13
+
+config SCB0_MI5_SLOT2
+	int "Slot 2 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI5_SLOT3
+	int "Slot 3 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI5_SLOT4
+	int "Slot 4 slave interface id"
+	default 1
+	range 0 13
+
+config SCB0_MI5_SLOT5
+	int "Slot 5 slave interface id"
+	default 3
+	range 0 13
+
+config SCB0_MI5_SLOT6
+	int "Slot 6 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI5_SLOT7
+	int "Slot 7 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI5_SLOT8
+	int "Slot 8 slave interface id"
+	default 1
+	range 0 13
+
+config SCB0_MI5_SLOT9
+	int "Slot 9 slave interface id"
+	default 3
+	range 0 13
+
+config SCB0_MI5_SLOT10
+	int "Slot 10 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI5_SLOT11
+	int "Slot 11 slave interface id"
+	default 12
+	range 0 13
+
+config SCB0_MI5_SLOT12
+	int "Slot 12 slave interface id"
+	default 1
+	range 0 13
+
+config SCB0_MI5_SLOT13
+	int "Slot 13 slave interface id"
+	default 3
+	range 0 13
+
+config SCB0_MI5_SLOT14
+	int "Slot 14 slave interface id"
+	default 10
+	range 0 13
+
+config SCB0_MI5_SLOT15
+	int "Slot 15 slave interface id"
+	default 12
+	range 0 13
+
+endif # SCB0_MI5
+
+menuconfig	SCB1_MI0
+	bool "SCB1 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	SPORT0A	-- 0
+	SPORT0B	-- 1
+	SPORT1A	-- 2
+	SPORT1B	-- 3
+	SPORT2A	-- 4
+	SPORT2B	-- 5
+	SPI0TX	-- 6
+	SPI0RX	-- 7
+	SPI1TX	-- 8
+	SPI1RX	-- 9
+
+if SCB1_MI0
+
+config SCB1_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 9
+
+config SCB1_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 9
+
+config SCB1_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 9
+
+config SCB1_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 9
+
+config SCB1_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 4
+	range 0 9
+
+config SCB1_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 5
+	range 0 9
+
+config SCB1_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 6
+	range 0 9
+
+config SCB1_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 7
+	range 0 9
+
+config SCB1_MI0_SLOT8
+	int "Slot 8 slave interface id"
+	default 8
+	range 0 9
+
+config SCB1_MI0_SLOT9
+	int "Slot 9 slave interface id"
+	default 9
+	range 0 9
+
+config SCB1_MI0_SLOT10
+	int "Slot 10 slave interface id"
+	default 0
+	range 0 9
+
+config SCB1_MI0_SLOT11
+	int "Slot 11 slave interface id"
+	default 1
+	range 0 9
+
+config SCB1_MI0_SLOT12
+	int "Slot 12 slave interface id"
+	default 2
+	range 0 9
+
+config SCB1_MI0_SLOT13
+	int "Slot 13 slave interface id"
+	default 3
+	range 0 9
+
+config SCB1_MI0_SLOT14
+	int "Slot 14 slave interface id"
+	default 4
+	range 0 9
+
+config SCB1_MI0_SLOT15
+	int "Slot 15 slave interface id"
+	default 5
+	range 0 9
+
+config SCB1_MI0_SLOT16
+	int "Slot 16 slave interface id"
+	default 6
+	range 0 13
+
+config SCB1_MI0_SLOT17
+	int "Slot 17 slave interface id"
+	default 7
+	range 0 13
+
+config SCB1_MI0_SLOT18
+	int "Slot 18 slave interface id"
+	default 8
+	range 0 13
+
+config SCB1_MI0_SLOT19
+	int "Slot 19 slave interface id"
+	default 9
+	range 0 13
+
+endif # SCB1_MI0
+
+menuconfig	SCB2_MI0
+	bool "SCB2 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	RSI	-- 0
+	SDU DMA	-- 1
+	SDU	-- 2
+	EMAC0	-- 3
+	EMAC1	-- 4
+
+if SCB2_MI0
+
+config SCB2_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 4
+
+config SCB2_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 4
+
+config SCB2_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 4
+
+config SCB2_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 4
+
+config SCB2_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 4
+	range 0 4
+
+config SCB2_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 0
+	range 0 4
+
+config SCB2_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 1
+	range 0 4
+
+config SCB2_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 2
+	range 0 4
+
+config SCB2_MI0_SLOT8
+	int "Slot 8 slave interface id"
+	default 3
+	range 0 4
+
+config SCB2_MI0_SLOT9
+	int "Slot 9 slave interface id"
+	default 4
+	range 0 4
+
+endif # SCB2_MI0
+
+menuconfig	SCB3_MI0
+	bool "SCB3 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	LP0	-- 0
+	LP1	-- 1
+	LP2	-- 2
+	LP3	-- 3
+	UART0TX	-- 4
+	UART0RX	-- 5
+	UART1TX	-- 4
+	UART1RX	-- 5
+
+if SCB3_MI0
+
+config SCB3_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 7
+
+config SCB3_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 7
+
+config SCB3_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 7
+
+config SCB3_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 7
+
+config SCB3_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 4
+	range 0 7
+
+config SCB3_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 5
+	range 0 7
+
+config SCB3_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 6
+	range 0 7
+
+config SCB3_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 7
+	range 0 7
+
+config SCB3_MI0_SLOT8
+	int "Slot 8 slave interface id"
+	default 0
+	range 0 7
+
+config SCB3_MI0_SLOT9
+	int "Slot 9 slave interface id"
+	default 1
+	range 0 7
+
+config SCB3_MI0_SLOT10
+	int "Slot 10 slave interface id"
+	default 2
+	range 0 7
+
+config SCB3_MI0_SLOT11
+	int "Slot 11 slave interface id"
+	default 3
+	range 0 7
+
+config SCB3_MI0_SLOT12
+	int "Slot 12 slave interface id"
+	default 4
+	range 0 7
+
+config SCB3_MI0_SLOT13
+	int "Slot 13 slave interface id"
+	default 5
+	range 0 7
+
+config SCB3_MI0_SLOT14
+	int "Slot 14 slave interface id"
+	default 6
+	range 0 7
+
+config SCB3_MI0_SLOT15
+	int "Slot 15 slave interface id"
+	default 7
+	range 0 7
+
+endif # SCB3_MI0
+
+menuconfig	SCB4_MI0
+	bool "SCB4 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	MDA21	-- 0
+	MDA22	-- 1
+	MDA23	-- 2
+	MDA24	-- 3
+	MDA25	-- 4
+	MDA26	-- 5
+	MDA27	-- 6
+	MDA28	-- 7
+
+if SCB4_MI0
+
+config SCB4_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 7
+
+config SCB4_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 7
+
+config SCB4_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 7
+
+config SCB4_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 7
+
+config SCB4_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 4
+	range 0 7
+
+config SCB4_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 5
+	range 0 7
+
+config SCB4_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 6
+	range 0 7
+
+config SCB4_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 7
+	range 0 7
+
+config SCB4_MI0_SLOT8
+	int "Slot 8 slave interface id"
+	default 0
+	range 0 7
+
+config SCB4_MI0_SLOT9
+	int "Slot 9 slave interface id"
+	default 1
+	range 0 7
+
+config SCB4_MI0_SLOT10
+	int "Slot 10 slave interface id"
+	default 2
+	range 0 7
+
+config SCB4_MI0_SLOT11
+	int "Slot 11 slave interface id"
+	default 3
+	range 0 7
+
+config SCB4_MI0_SLOT12
+	int "Slot 12 slave interface id"
+	default 4
+	range 0 7
+
+config SCB4_MI0_SLOT13
+	int "Slot 13 slave interface id"
+	default 5
+	range 0 7
+
+config SCB4_MI0_SLOT14
+	int "Slot 14 slave interface id"
+	default 6
+	range 0 7
+
+config SCB4_MI0_SLOT15
+	int "Slot 15 slave interface id"
+	default 7
+	range 0 7
+
+endif # SCB4_MI0
+
+menuconfig	SCB5_MI0
+	bool "SCB5 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	PPI0 MDA29	-- 0
+	PPI0 MDA30	-- 1
+	PPI2 MDA31	-- 2
+	PPI2 MDA32	-- 3
+
+if SCB5_MI0
+
+config SCB5_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 3
+
+config SCB5_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 3
+
+config SCB5_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 3
+
+config SCB5_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 3
+
+config SCB5_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 0
+	range 0 3
+
+config SCB5_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 1
+	range 0 3
+
+config SCB5_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 2
+	range 0 3
+
+config SCB5_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 3
+	range 0 3
+
+endif # SCB5_MI0
+
+menuconfig	SCB6_MI0
+	bool "SCB6 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	PPI1 MDA33	-- 0
+	PPI1 MDA34	-- 1
+
+if SCB6_MI0
+
+config SCB6_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 1
+
+config SCB6_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 1
+
+config SCB6_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 0
+	range 0 1
+
+config SCB6_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 1
+	range 0 1
+
+endif # SCB6_MI0
+
+menuconfig	SCB7_MI0
+	bool "SCB7 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	PIXC0	-- 0
+	PIXC1	-- 1
+	PIXC2	-- 2
+
+if SCB7_MI0
+
+config SCB7_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 2
+
+config SCB7_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 2
+
+config SCB7_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 2
+
+config SCB7_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 0
+	range 0 2
+
+config SCB7_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 1
+	range 0 2
+
+config SCB7_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 2
+	range 0 2
+
+endif # SCB7_MI0
+
+menuconfig	SCB8_MI0
+	bool "SCB8 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	PVP CPDOB	-- 0
+	PVP CPDOC	-- 1
+	PVP CPCO	-- 2
+	PVP CPCI	-- 3
+
+if SCB8_MI0
+
+config SCB8_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 3
+
+config SCB8_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 3
+
+config SCB8_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 3
+
+config SCB8_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 3
+
+config SCB8_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 0
+	range 0 3
+
+config SCB8_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 1
+	range 0 3
+
+config SCB8_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 2
+	range 0 3
+
+config SCB8_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 3
+	range 0 3
+
+endif # SCB8_MI0
+
+menuconfig	SCB9_MI0
+	bool "SCB9 Master Interface 0"
+	default n
+	depends on SCB_PRIORITY
+	help
+	The slave interface id of each slot should be set according following table.
+	PVP MPDO	-- 0
+	PVP MPDI	-- 1
+	PVP MPCO	-- 2
+	PVP MPCI	-- 3
+	PVP CPDOA	-- 4
+
+if SCB9_MI0
+
+config SCB9_MI0_SLOT0
+	int "Slot 0 slave interface id"
+	default 0
+	range 0 4
+
+config SCB9_MI0_SLOT1
+	int "Slot 1 slave interface id"
+	default 1
+	range 0 4
+
+config SCB9_MI0_SLOT2
+	int "Slot 2 slave interface id"
+	default 2
+	range 0 4
+
+config SCB9_MI0_SLOT3
+	int "Slot 3 slave interface id"
+	default 3
+	range 0 4
+
+config SCB9_MI0_SLOT4
+	int "Slot 4 slave interface id"
+	default 4
+	range 0 4
+
+config SCB9_MI0_SLOT5
+	int "Slot 5 slave interface id"
+	default 0
+	range 0 4
+
+config SCB9_MI0_SLOT6
+	int "Slot 6 slave interface id"
+	default 1
+	range 0 4
+
+config SCB9_MI0_SLOT7
+	int "Slot 7 slave interface id"
+	default 2
+	range 0 4
+
+config SCB9_MI0_SLOT8
+	int "Slot 8 slave interface id"
+	default 3
+	range 0 4
+
+config SCB9_MI0_SLOT9
+	int "Slot 9 slave interface id"
+	default 4
+	range 0 4
+
+endif # SCB9_MI0
+
 endmenu
 
 endif
diff --git a/arch/blackfin/mach-bf609/Makefile b/arch/blackfin/mach-bf609/Makefile
index 234fe1b4bb0..60ffaf85d30 100644
--- a/arch/blackfin/mach-bf609/Makefile
+++ b/arch/blackfin/mach-bf609/Makefile
@@ -4,3 +4,4 @@
 
 obj-y := dma.o clock.o ints-priority.o
 obj-$(CONFIG_PM) += pm.o dpm.o
+obj-$(CONFIG_SCB_PRIORITY) += scb.o
diff --git a/arch/blackfin/mach-bf609/boards/ezkit.c b/arch/blackfin/mach-bf609/boards/ezkit.c
index 0bc47231540..e2c0b024ce8 100644
--- a/arch/blackfin/mach-bf609/boards/ezkit.c
+++ b/arch/blackfin/mach-bf609/boards/ezkit.c
@@ -17,7 +17,10 @@
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/usb/musb.h>
-#include <asm/bfin_spi3.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/platform_data/pinctrl-adi2.h>
+#include <linux/spi/adi_spi3.h>
 #include <asm/dma.h>
 #include <asm/gpio.h>
 #include <asm/nand.h>
@@ -36,7 +39,7 @@ const char bfin_board_name[] = "ADI BF609-EZKIT";
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 #include <linux/usb/isp1760.h>
 static struct resource bfin_isp1760_resources[] = {
 	[0] = {
@@ -71,7 +74,7 @@ static struct platform_device bfin_isp1760_device = {
 };
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 #include <asm/bfin_rotary.h>
 
 static struct bfin_rotary_platform_data bfin_rotary_data = {
@@ -102,20 +105,34 @@ static struct platform_device bfin_rotary_device = {
 };
 #endif
 
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
+#if IS_ENABLED(CONFIG_STMMAC_ETH)
 #include <linux/stmmac.h>
-
-static unsigned short pins[] = P_RMII0;
+#include <linux/phy.h>
 
 static struct stmmac_mdio_bus_data phy_private_data = {
 	.phy_mask = 1,
 };
 
+static struct stmmac_dma_cfg eth_dma_cfg = {
+	.pbl	= 2,
+};
+
+int stmmac_ptp_clk_init(struct platform_device *pdev, void *priv)
+{
+	bfin_write32(PADS0_EMAC_PTP_CLKSEL, 0);
+	return 0;
+}
+
 static struct plat_stmmacenet_data eth_private_data = {
+	.has_gmac = 1,
 	.bus_id   = 0,
 	.enh_desc = 1,
 	.phy_addr = 1,
 	.mdio_bus_data = &phy_private_data,
+	.dma_cfg  = &eth_dma_cfg,
+	.force_thresh_dma_mode = 1,
+	.interface = PHY_INTERFACE_MODE_RMII,
+	.init = stmmac_ptp_clk_init,
 };
 
 static struct platform_device bfin_eth_device = {
@@ -142,7 +159,7 @@ static struct platform_device bfin_eth_device = {
 };
 #endif
 
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
 #include <linux/input/adxl34x.h>
 static const struct adxl34x_platform_data adxl34x_info = {
 	.x_axis_offset = 0,
@@ -181,14 +198,14 @@ static const struct adxl34x_platform_data adxl34x_info = {
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
@@ -196,6 +213,18 @@ static struct resource bfin_uart0_resources[] = {
 		.end = UART0_RXDIV+4,
 		.flags = IORESOURCE_MEM,
 	},
+#ifdef CONFIG_EARLY_PRINTK
+	{
+		.start = PORTD_FER,
+		.end = PORTD_FER+2,
+		.flags = IORESOURCE_REG,
+	},
+	{
+		.start = PORTD_MUX,
+		.end = PORTD_MUX+3,
+		.flags = IORESOURCE_REG,
+	},
+#endif
 	{
 		.start = IRQ_UART0_TX,
 		.end = IRQ_UART0_TX,
@@ -260,6 +289,13 @@ static struct resource bfin_uart1_resources[] = {
 		.end = UART1_RXDIV+4,
 		.flags = IORESOURCE_MEM,
 	},
+#ifdef CONFIG_EARLY_PRINTK
+	{
+		.start = PORTG_FER_SET,
+		.end = PORTG_FER_SET+2,
+		.flags = IORESOURCE_REG,
+	},
+#endif
 	{
 		.start = IRQ_UART1_TX,
 		.end = IRQ_UART1_TX,
@@ -319,7 +355,7 @@ static struct platform_device bfin_uart1_device = {
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
@@ -372,7 +408,7 @@ static struct platform_device bfin_sir1_device = {
 #endif
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 static struct resource musb_resources[] = {
 	[0] = {
 		.start	= 0xFFCC1000,
@@ -428,7 +464,7 @@ static struct platform_device musb_device = {
 };
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
@@ -533,7 +569,7 @@ static struct platform_device bfin_sport2_uart_device = {
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 
 static unsigned short bfin_can0_peripherals[] = {
 	P_CAN0_RX, P_CAN0_TX, 0
@@ -574,7 +610,7 @@ static struct platform_device bfin_can0_device = {
 
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 static struct mtd_partition partition_info[] = {
 	{
 		.name = "bootloader(nand)",
@@ -624,7 +660,7 @@ static struct platform_device bfin_nand_device = {
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_RSI,
@@ -641,7 +677,7 @@ static struct platform_device bfin_sdh_device = {
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
@@ -658,16 +694,9 @@ static struct mtd_partition ezkit_partitions[] = {
 	},
 };
 
-int bf609_nor_flash_init(struct platform_device *dev)
+int bf609_nor_flash_init(struct platform_device *pdev)
 {
 #define CONFIG_SMC_GCTL_VAL     0x00000010
-	const unsigned short pins[] = {
-		P_A3, P_A4, P_A5, P_A6, P_A7, P_A8, P_A9, P_A10, P_A11, P_A12,
-		P_A13, P_A14, P_A15, P_A16, P_A17, P_A18, P_A19, P_A20, P_A21,
-		P_A22, P_A23, P_A24, P_A25, P_NORCK, 0,
-	};
-
-	peripheral_request_list(pins, "smc0");
 
 	bfin_write32(SMC_GCTL, CONFIG_SMC_GCTL_VAL);
 	bfin_write32(SMC_B0CTL, 0x01002011);
@@ -676,16 +705,8 @@ int bf609_nor_flash_init(struct platform_device *dev)
 	return 0;
 }
 
-void bf609_nor_flash_exit(struct platform_device *dev)
+void bf609_nor_flash_exit(struct platform_device *pdev)
 {
-	const unsigned short pins[] = {
-		P_A3, P_A4, P_A5, P_A6, P_A7, P_A8, P_A9, P_A10, P_A11, P_A12,
-		P_A13, P_A14, P_A15, P_A16, P_A17, P_A18, P_A19, P_A20, P_A21,
-		P_A22, P_A23, P_A24, P_A25, P_NORCK, 0,
-	};
-
-	peripheral_free_list(pins);
-
 	bfin_write32(SMC_GCTL, 0);
 }
 
@@ -717,8 +738,7 @@ static struct platform_device ezkit_flash_device = {
 };
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 /* SPI flash chip (w25q32) */
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
@@ -744,26 +764,25 @@ static struct flash_platform_data bfin_spi_flash_data = {
 	.type = "w25q32",
 };
 
-static struct bfin_spi3_chip spi_flash_chip_info = {
+static struct adi_spi3_chip spi_flash_chip_info = {
 	.enable_dma = true,         /* use dma transfer with this chip*/
 };
 #endif
 
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin_spi3_chip spidev_chip_info = {
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
+static struct adi_spi3_chip spidev_chip_info = {
 	.enable_dma = true,
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s_pcm = {
 	.name = "bfin-i2s-pcm-audio",
 	.id = -1,
 };
 #endif
 
-#if defined(CONFIG_SND_BF6XX_SOC_I2S) || \
-	defined(CONFIG_SND_BF6XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF6XX_SOC_I2S)
 #include <asm/bfin_sport3.h>
 static struct resource bfin_snd_resources[] = {
 	{
@@ -817,8 +836,7 @@ static struct platform_device bfin_i2s = {
 };
 #endif
 
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
-	        || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 static const char * const ad1836_link[] = {
 	"bfin-i2s.0",
 	"spi0.76",
@@ -832,14 +850,13 @@ static struct platform_device bfin_ad1836_machine = {
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61)
 static struct platform_device adau1761_device = {
 	.name = "bfin-eval-adau1x61",
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
 #include <sound/adau17x1.h>
 static struct adau1761_platform_data adau1761_info = {
 	.lineout_mode = ADAU1761_OUTPUT_MODE_LINE,
@@ -847,8 +864,7 @@ static struct adau1761_platform_data adau1761_info = {
 };
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_capture.h>
 #include <media/blackfin/ppi.h>
@@ -858,7 +874,7 @@ static const unsigned short ppi_req[] = {
 	P_PPI0_D4, P_PPI0_D5, P_PPI0_D6, P_PPI0_D7,
 	P_PPI0_D8, P_PPI0_D9, P_PPI0_D10, P_PPI0_D11,
 	P_PPI0_D12, P_PPI0_D13, P_PPI0_D14, P_PPI0_D15,
-#if !defined(CONFIG_VIDEO_VS6624) && !defined(CONFIG_VIDEO_VS6624_MODULE)
+#if !IS_ENABLED(CONFIG_VIDEO_VS6624)
 	P_PPI0_D16, P_PPI0_D17, P_PPI0_D18, P_PPI0_D19,
 	P_PPI0_D20, P_PPI0_D21, P_PPI0_D22, P_PPI0_D23,
 #endif
@@ -874,8 +890,7 @@ static const struct ppi_info ppi_info = {
 	.pin_req = ppi_req,
 };
 
-#if defined(CONFIG_VIDEO_VS6624) \
-	|| defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
 static struct v4l2_input vs6624_inputs[] = {
 	{
 		.index = 0,
@@ -912,8 +927,7 @@ static struct bfin_capture_config bfin_capture_data = {
 };
 #endif
 
-#if defined(CONFIG_VIDEO_ADV7842) \
-	|| defined(CONFIG_VIDEO_ADV7842_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7842)
 #include <media/adv7842.h>
 
 static struct v4l2_input adv7842_inputs[] = {
@@ -1001,7 +1015,9 @@ static struct adv7842_platform_data adv7842_data = {
 	.ain_sel = ADV7842_AIN10_11_12_NC_SYNC_4_1,
 	.prim_mode = ADV7842_PRIM_MODE_SDP,
 	.vid_std_select = ADV7842_SDP_VID_STD_CVBS_SD_4x1,
-	.inp_color_space = ADV7842_INP_COLOR_SPACE_AUTO,
+	.hdmi_free_run_enable = 1,
+	.sdp_free_run_auto = 1,
+	.llc_dll_phase = 0x10,
 	.i2c_sdp_io = 0x40,
 	.i2c_sdp = 0x41,
 	.i2c_cp = 0x42,
@@ -1041,8 +1057,7 @@ static struct platform_device bfin_capture_device = {
 };
 #endif
 
-#if defined(CONFIG_VIDEO_BLACKFIN_DISPLAY) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_DISPLAY_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_DISPLAY)
 #include <linux/videodev2.h>
 #include <media/blackfin/bfin_display.h>
 #include <media/blackfin/ppi.h>
@@ -1064,8 +1079,7 @@ static const struct ppi_info ppi_info = {
 	.pin_req = ppi_req_disp,
 };
 
-#if defined(CONFIG_VIDEO_ADV7511) \
-	|| defined(CONFIG_VIDEO_ADV7511_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7511)
 #include <media/adv7511.h>
 
 static struct v4l2_output adv7511_outputs[] = {
@@ -1107,6 +1121,81 @@ static struct bfin_display_config bfin_display_data = {
 };
 #endif
 
+#if IS_ENABLED(CONFIG_VIDEO_ADV7343)
+#include <media/adv7343.h>
+
+static struct v4l2_output adv7343_outputs[] = {
+	{
+		.index = 0,
+		.name = "Composite",
+		.type = V4L2_OUTPUT_TYPE_ANALOG,
+		.std = V4L2_STD_ALL,
+		.capabilities = V4L2_OUT_CAP_STD,
+	},
+	{
+		.index = 1,
+		.name = "S-Video",
+		.type = V4L2_OUTPUT_TYPE_ANALOG,
+		.std = V4L2_STD_ALL,
+		.capabilities = V4L2_OUT_CAP_STD,
+	},
+	{
+		.index = 2,
+		.name = "Component",
+		.type = V4L2_OUTPUT_TYPE_ANALOG,
+		.std = V4L2_STD_ALL,
+		.capabilities = V4L2_OUT_CAP_STD,
+	},
+
+};
+
+static struct disp_route adv7343_routes[] = {
+	{
+		.output = ADV7343_COMPOSITE_ID,
+	},
+	{
+		.output = ADV7343_SVIDEO_ID,
+	},
+	{
+		.output = ADV7343_COMPONENT_ID,
+	},
+};
+
+static struct adv7343_platform_data adv7343_data = {
+	.mode_config = {
+		.sleep_mode = false,
+		.pll_control = false,
+		.dac_1 = true,
+		.dac_2 = true,
+		.dac_3 = true,
+		.dac_4 = true,
+		.dac_5 = true,
+		.dac_6 = true,
+	},
+	.sd_config = {
+		.sd_dac_out1 = false,
+		.sd_dac_out2 = false,
+	},
+};
+
+static struct bfin_display_config bfin_display_data = {
+	.card_name = "BF609",
+	.outputs = adv7343_outputs,
+	.num_outputs = ARRAY_SIZE(adv7343_outputs),
+	.routes = adv7343_routes,
+	.i2c_adapter_id = 0,
+	.board_info = {
+		.type = "adv7343",
+		.addr = 0x2b,
+		.platform_data = (void *)&adv7343_data,
+	},
+	.ppi_info = &ppi_info_disp,
+	.ppi_control = (PACK_EN | DLEN_8 | EPPI_CTL_FS1LO_FS2LO
+			| EPPI_CTL_POLC3 | EPPI_CTL_BLANKGEN | EPPI_CTL_SYNC2
+			| EPPI_CTL_NON656 | EPPI_CTL_DIR),
+};
+#endif
+
 static struct platform_device bfin_display_device = {
 	.name = "bfin_display",
 	.dev = {
@@ -1212,7 +1301,7 @@ static struct platform_device bfin_crypto_crc_device = {
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -1228,7 +1317,357 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#ifdef CONFIG_PINCTRL_ADI2
+
+# define ADI_PINT_DEVNAME "adi-gpio-pint"
+# define ADI_GPIO_DEVNAME "adi-gpio"
+# define ADI_PINCTRL_DEVNAME "pinctrl-adi2"
+
+static struct platform_device bfin_pinctrl_device = {
+	.name = ADI_PINCTRL_DEVNAME,
+	.id = 0,
+};
+
+static struct resource bfin_pint0_resources[] = {
+	{
+		.start = PINT0_MASK_SET,
+		.end = PINT0_LATCH + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PINT0,
+		.end = IRQ_PINT0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pint0_device = {
+	.name = ADI_PINT_DEVNAME,
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_pint0_resources),
+	.resource = bfin_pint0_resources,
+};
+
+static struct resource bfin_pint1_resources[] = {
+	{
+		.start = PINT1_MASK_SET,
+		.end = PINT1_LATCH + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PINT1,
+		.end = IRQ_PINT1,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pint1_device = {
+	.name = ADI_PINT_DEVNAME,
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_pint1_resources),
+	.resource = bfin_pint1_resources,
+};
+
+static struct resource bfin_pint2_resources[] = {
+	{
+		.start = PINT2_MASK_SET,
+		.end = PINT2_LATCH + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PINT2,
+		.end = IRQ_PINT2,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pint2_device = {
+	.name = ADI_PINT_DEVNAME,
+	.id = 2,
+	.num_resources = ARRAY_SIZE(bfin_pint2_resources),
+	.resource = bfin_pint2_resources,
+};
+
+static struct resource bfin_pint3_resources[] = {
+	{
+		.start = PINT3_MASK_SET,
+		.end = PINT3_LATCH + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PINT3,
+		.end = IRQ_PINT3,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pint3_device = {
+	.name = ADI_PINT_DEVNAME,
+	.id = 3,
+	.num_resources = ARRAY_SIZE(bfin_pint3_resources),
+	.resource = bfin_pint3_resources,
+};
+
+static struct resource bfin_pint4_resources[] = {
+	{
+		.start = PINT4_MASK_SET,
+		.end = PINT4_LATCH + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PINT4,
+		.end = IRQ_PINT4,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pint4_device = {
+	.name = ADI_PINT_DEVNAME,
+	.id = 4,
+	.num_resources = ARRAY_SIZE(bfin_pint4_resources),
+	.resource = bfin_pint4_resources,
+};
+
+static struct resource bfin_pint5_resources[] = {
+	{
+		.start = PINT5_MASK_SET,
+		.end = PINT5_LATCH + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PINT5,
+		.end = IRQ_PINT5,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pint5_device = {
+	.name = ADI_PINT_DEVNAME,
+	.id = 5,
+	.num_resources = ARRAY_SIZE(bfin_pint5_resources),
+	.resource = bfin_pint5_resources,
+};
+
+static struct resource bfin_gpa_resources[] = {
+	{
+		.start = PORTA_FER,
+		.end = PORTA_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{	/* optional */
+		.start = IRQ_PA0,
+		.end = IRQ_PA0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpa_pdata = {
+	.port_pin_base	= GPIO_PA0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 0,		/* PINT0 */
+	.pint_assign	= true,		/* PINT upper 16 bit */
+	.pint_map	= 0,		/* mapping mask in PINT */
+};
+
+static struct platform_device bfin_gpa_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_gpa_resources),
+	.resource = bfin_gpa_resources,
+	.dev = {
+		.platform_data = &bfin_gpa_pdata, /* Passed to driver */
+	},
+};
+
+static struct resource bfin_gpb_resources[] = {
+	{
+		.start = PORTB_FER,
+		.end = PORTB_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PB0,
+		.end = IRQ_PB0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpb_pdata = {
+	.port_pin_base	= GPIO_PB0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 0,
+	.pint_assign	= false,
+	.pint_map	= 1,
+};
+
+static struct platform_device bfin_gpb_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_gpb_resources),
+	.resource = bfin_gpb_resources,
+	.dev = {
+		.platform_data = &bfin_gpb_pdata, /* Passed to driver */
+	},
+};
+
+static struct resource bfin_gpc_resources[] = {
+	{
+		.start = PORTC_FER,
+		.end = PORTC_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PC0,
+		.end = IRQ_PC0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpc_pdata = {
+	.port_pin_base	= GPIO_PC0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 1,
+	.pint_assign	= false,
+	.pint_map	= 1,
+};
+
+static struct platform_device bfin_gpc_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 2,
+	.num_resources = ARRAY_SIZE(bfin_gpc_resources),
+	.resource = bfin_gpc_resources,
+	.dev = {
+		.platform_data = &bfin_gpc_pdata, /* Passed to driver */
+	},
+};
+
+static struct resource bfin_gpd_resources[] = {
+	{
+		.start = PORTD_FER,
+		.end = PORTD_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PD0,
+		.end = IRQ_PD0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpd_pdata = {
+	.port_pin_base	= GPIO_PD0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 2,
+	.pint_assign	= false,
+	.pint_map	= 1,
+};
+
+static struct platform_device bfin_gpd_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 3,
+	.num_resources = ARRAY_SIZE(bfin_gpd_resources),
+	.resource = bfin_gpd_resources,
+	.dev = {
+		.platform_data = &bfin_gpd_pdata, /* Passed to driver */
+	},
+};
+
+static struct resource bfin_gpe_resources[] = {
+	{
+		.start = PORTE_FER,
+		.end = PORTE_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PE0,
+		.end = IRQ_PE0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpe_pdata = {
+	.port_pin_base	= GPIO_PE0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 3,
+	.pint_assign	= false,
+	.pint_map	= 1,
+};
+
+static struct platform_device bfin_gpe_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 4,
+	.num_resources = ARRAY_SIZE(bfin_gpe_resources),
+	.resource = bfin_gpe_resources,
+	.dev = {
+		.platform_data = &bfin_gpe_pdata, /* Passed to driver */
+	},
+};
+
+static struct resource bfin_gpf_resources[] = {
+	{
+		.start = PORTF_FER,
+		.end = PORTF_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PF0,
+		.end = IRQ_PF0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpf_pdata = {
+	.port_pin_base	= GPIO_PF0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 4,
+	.pint_assign	= false,
+	.pint_map	= 1,
+};
+
+static struct platform_device bfin_gpf_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 5,
+	.num_resources = ARRAY_SIZE(bfin_gpf_resources),
+	.resource = bfin_gpf_resources,
+	.dev = {
+		.platform_data = &bfin_gpf_pdata, /* Passed to driver */
+	},
+};
+
+static struct resource bfin_gpg_resources[] = {
+	{
+		.start = PORTG_FER,
+		.end = PORTG_MUX + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PG0,
+		.end = IRQ_PG0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct adi_pinctrl_gpio_platform_data bfin_gpg_pdata = {
+	.port_pin_base	= GPIO_PG0,
+	.port_width	= GPIO_BANKSIZE,
+	.pint_id	= 5,
+	.pint_assign	= false,
+	.pint_map	= 1,
+};
+
+static struct platform_device bfin_gpg_device = {
+	.name = ADI_GPIO_DEVNAME,
+	.id = 6,
+	.num_resources = ARRAY_SIZE(bfin_gpg_resources),
+	.resource = bfin_gpg_resources,
+	.dev = {
+		.platform_data = &bfin_gpg_pdata, /* Passed to driver */
+	},
+};
+
+#endif
+
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
@@ -1251,39 +1690,38 @@ static struct platform_device bfin_device_gpiokeys = {
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* SPI_SSEL1*/
+		.chip_select = MAX_CTRL_CS + GPIO_PD11, /* SPI_SSEL1*/
 		.platform_data = &bfin_spi_flash_data,
 		.controller_data = &spi_flash_chip_info,
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
 		.irq			= IRQ_PD9,
 		.max_speed_hz		= 12500000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num		= 0,
-		.chip_select  		= 4,
+		.chip_select		= MAX_CTRL_CS + GPIO_PC15, /* SPI_SSEL4 */
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = 1,
+		.chip_select = MAX_CTRL_CS + GPIO_PD11, /* SPI_SSEL1*/
 		.controller_data = &spidev_chip_info,
 	},
 #endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
 	{
 		.modalias		= "adxl34x",
 		.platform_data		= &adxl34x_info,
@@ -1295,7 +1733,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 };
-#if IS_ENABLED(CONFIG_SPI_BFIN_V3)
+#if IS_ENABLED(CONFIG_SPI_ADI_V3)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	{
@@ -1336,13 +1774,13 @@ static struct resource bfin_spi1_resource[] = {
 };
 
 /* SPI controller data */
-static struct bfin_spi3_master bf60x_spi_master_info0 = {
+static struct adi_spi3_master bf60x_spi_master_info0 = {
 	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
 
 static struct platform_device bf60x_spi_master0 = {
-	.name = "bfin-spi3",
+	.name = "adi-spi3",
 	.id = 0, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
 	.resource = bfin_spi0_resource,
@@ -1351,13 +1789,13 @@ static struct platform_device bf60x_spi_master0 = {
 	},
 };
 
-static struct bfin_spi3_master bf60x_spi_master_info1 = {
+static struct adi_spi3_master bf60x_spi_master_info1 = {
 	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
 
 static struct platform_device bf60x_spi_master1 = {
-	.name = "bfin-spi3",
+	.name = "adi-spi3",
 	.id = 1, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_spi1_resource),
 	.resource = bfin_spi1_resource,
@@ -1367,7 +1805,7 @@ static struct platform_device bf60x_spi_master1 = {
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
@@ -1420,20 +1858,20 @@ static struct platform_device i2c_bfin_twi1_device = {
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
 	{
 		I2C_BOARD_INFO("adxl34x", 0x53),
 		.irq = IRQ_PC5,
 		.platform_data = (void *)&adxl34x_info,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
 	{
 		I2C_BOARD_INFO("adau1761", 0x38),
 		.platform_data = (void *)&adau1761_info
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
@@ -1474,12 +1912,28 @@ static struct platform_device bfin_dpmc = {
 static struct platform_device *ezkit_devices[] __initdata = {
 
 	&bfin_dpmc,
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if defined(CONFIG_PINCTRL_ADI2)
+	&bfin_pinctrl_device,
+	&bfin_pint0_device,
+	&bfin_pint1_device,
+	&bfin_pint2_device,
+	&bfin_pint3_device,
+	&bfin_pint4_device,
+	&bfin_pint5_device,
+	&bfin_gpa_device,
+	&bfin_gpb_device,
+	&bfin_gpc_device,
+	&bfin_gpd_device,
+	&bfin_gpe_device,
+	&bfin_gpf_device,
+	&bfin_gpg_device,
+#endif
+
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
@@ -1488,7 +1942,7 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
@@ -1497,19 +1951,19 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 #endif
 
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
+#if IS_ENABLED(CONFIG_STMMAC_ETH)
 	&bfin_eth_device,
 #endif
 
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
 	&musb_device,
 #endif
 
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
 	&bfin_isp1760_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
@@ -1521,28 +1975,28 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 #endif
 
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
 	&bfin_can0_device,
 #endif
 
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
 	&bfin_nand_device,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bfin_sdh_device,
 #endif
 
-#if IS_ENABLED(CONFIG_SPI_BFIN_V3)
+#if IS_ENABLED(CONFIG_SPI_ADI_V3)
 	&bf60x_spi_master0,
 	&bf60x_spi_master1,
 #endif
 
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
 	&bfin_rotary_device,
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi0_device,
 #if !defined(CONFIG_BF542)
 	&i2c_bfin_twi1_device,
@@ -1557,53 +2011,79 @@ static struct platform_device *ezkit_devices[] __initdata = {
 	&bfin_crypto_crc_device,
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezkit_flash_device,
 #endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s_pcm,
 #endif
-#if defined(CONFIG_SND_BF6XX_SOC_I2S) || \
-	defined(CONFIG_SND_BF6XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF6XX_SOC_I2S)
 	&bfin_i2s,
 #endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
-	defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
 	&bfin_ad1836_machine,
 #endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61) || \
-	defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61)
 	&adau1761_device,
 #endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
 	&bfin_capture_device,
 #endif
-#if defined(CONFIG_VIDEO_BLACKFIN_DISPLAY) \
-	|| defined(CONFIG_VIDEO_BLACKFIN_DISPLAY_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_DISPLAY)
 	&bfin_display_device,
 #endif
 
 };
 
+/* Pin control settings */
+static struct pinctrl_map __initdata bfin_pinmux_map[] = {
+	/* per-device maps */
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.0",  "pinctrl-adi2.0", NULL, "uart0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.1",  "pinctrl-adi2.0", NULL, "uart1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.0",  "pinctrl-adi2.0", NULL, "uart0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.1",  "pinctrl-adi2.0", NULL, "uart1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-sdh.0",  "pinctrl-adi2.0", NULL, "rsi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("stmmaceth.0",  "pinctrl-adi2.0", NULL, "eth0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("adi-spi3.0",  "pinctrl-adi2.0", NULL, "spi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("adi-spi3.1",  "pinctrl-adi2.0", NULL, "spi1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("i2c-bfin-twi.0",  "pinctrl-adi2.0", NULL, "twi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("i2c-bfin-twi.1",  "pinctrl-adi2.0", NULL, "twi1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-rotary",  "pinctrl-adi2.0", NULL, "rotary"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin_can.0",  "pinctrl-adi2.0", NULL, "can0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("physmap-flash.0",  "pinctrl-adi2.0", NULL, "smc0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bf609_nl8048.2",  "pinctrl-adi2.0", "ppi2_16bgrp", "ppi2"),
+	PIN_MAP_MUX_GROUP("bfin_display.0", "8bit",  "pinctrl-adi2.0", "ppi2_8bgrp", "ppi2"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin_display.0",  "pinctrl-adi2.0", "ppi2_16bgrp", "ppi2"),
+	PIN_MAP_MUX_GROUP("bfin_display.0", "16bit",  "pinctrl-adi2.0", "ppi2_16bgrp", "ppi2"),
+	PIN_MAP_MUX_GROUP("bfin_capture.0", "8bit",  "pinctrl-adi2.0", "ppi0_8bgrp", "ppi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0",  "pinctrl-adi2.0", "ppi0_16bgrp", "ppi0"),
+	PIN_MAP_MUX_GROUP("bfin_capture.0", "16bit",  "pinctrl-adi2.0", "ppi0_16bgrp", "ppi0"),
+	PIN_MAP_MUX_GROUP("bfin_capture.0", "24bit",  "pinctrl-adi2.0", "ppi0_24bgrp", "ppi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.0",  "pinctrl-adi2.0", NULL, "sport0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.0",  "pinctrl-adi2.0", NULL, "sport0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.1",  "pinctrl-adi2.0", NULL, "sport1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.1",  "pinctrl-adi2.0", NULL, "sport1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.2",  "pinctrl-adi2.0", NULL, "sport2"),
+	PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.2",  "pinctrl-adi2.0", NULL, "sport2"),
+};
+
 static int __init ezkit_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 
+	/* Initialize pinmuxing */
+	pinctrl_register_mappings(bfin_pinmux_map,
+				ARRAY_SIZE(bfin_pinmux_map));
+
 	i2c_register_board_info(0, bfin_i2c_board_info0,
 				ARRAY_SIZE(bfin_i2c_board_info0));
 	i2c_register_board_info(1, bfin_i2c_board_info1,
 				ARRAY_SIZE(bfin_i2c_board_info1));
 
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
-	if (!peripheral_request_list(pins, "emac0"))
-		printk(KERN_ERR "%s(): request emac pins failed\n", __func__);
-#endif
-
 	platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
 
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
@@ -1622,18 +2102,6 @@ static struct platform_device *ezkit_early_devices[] __initdata = {
 	&bfin_uart1_device,
 #endif
 #endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
-#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
-	&bfin_sport0_uart_device,
-#endif
-#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
-	&bfin_sport1_uart_device,
-#endif
-#ifdef CONFIG_SERIAL_BFIN_SPORT2_UART
-	&bfin_sport2_uart_device,
-#endif
-#endif
 };
 
 void __init native_machine_early_platform_add_devices(void)
diff --git a/arch/blackfin/mach-bf609/clock.c b/arch/blackfin/mach-bf609/clock.c
index 437d56c8228..244fa4ab4c5 100644
--- a/arch/blackfin/mach-bf609/clock.c
+++ b/arch/blackfin/mach-bf609/clock.c
@@ -73,24 +73,6 @@ static void clk_reg_write_mask(u32 reg, uint32_t val, uint32_t mask)
 	bfin_write32(reg, val2);
 }
 
-static void clk_reg_set_bits(u32 reg, uint32_t mask)
-{
-	u32 val;
-
-	val = bfin_read32(reg);
-	val |= mask;
-	bfin_write32(reg, val);
-}
-
-static void clk_reg_clear_bits(u32 reg, uint32_t mask)
-{
-	u32 val;
-
-	val = bfin_read32(reg);
-	val &= ~mask;
-	bfin_write32(reg, val);
-}
-
 int wait_for_pll_align(void)
 {
 	int i = 10000;
@@ -120,6 +102,7 @@ void clk_disable(struct clk *clk)
 }
 EXPORT_SYMBOL(clk_disable);
 
+
 unsigned long clk_get_rate(struct clk *clk)
 {
 	unsigned long ret = 0;
@@ -131,7 +114,7 @@ EXPORT_SYMBOL(clk_get_rate);
 
 long clk_round_rate(struct clk *clk, unsigned long rate)
 {
-	long ret = -EIO;
+	long ret = 0;
 	if (clk->ops && clk->ops->round_rate)
 		ret = clk->ops->round_rate(clk, rate);
 	return ret;
@@ -220,6 +203,12 @@ unsigned long sys_clk_get_rate(struct clk *clk)
 	}
 }
 
+unsigned long dummy_get_rate(struct clk *clk)
+{
+	clk->parent->rate = clk_get_rate(clk->parent);
+	return clk->parent->rate;
+}
+
 unsigned long sys_clk_round_rate(struct clk *clk, unsigned long rate)
 {
 	unsigned long max_rate;
@@ -283,6 +272,10 @@ static struct clk_ops sys_clk_ops = {
 	.round_rate = sys_clk_round_rate,
 };
 
+static struct clk_ops dummy_clk_ops = {
+	.get_rate = dummy_get_rate,
+};
+
 static struct clk sys_clkin = {
 	.name       = "SYS_CLKIN",
 	.rate       = CONFIG_CLKIN_HZ,
@@ -364,6 +357,18 @@ static struct clk oclk = {
 	.parent     = &pll_clk,
 };
 
+static struct clk ethclk = {
+	.name       = "stmmaceth",
+	.parent     = &sclk0,
+	.ops	    = &dummy_clk_ops,
+};
+
+static struct clk spiclk = {
+	.name       = "spi",
+	.parent     = &sclk1,
+	.ops        = &dummy_clk_ops,
+};
+
 static struct clk_lookup bf609_clks[] = {
 	CLK(sys_clkin, NULL, "SYS_CLKIN"),
 	CLK(pll_clk, NULL, "PLLCLK"),
@@ -375,6 +380,8 @@ static struct clk_lookup bf609_clks[] = {
 	CLK(sclk1, NULL, "SCLK1"),
 	CLK(dclk, NULL, "DCLK"),
 	CLK(oclk, NULL, "OCLK"),
+	CLK(ethclk, NULL, "stmmaceth"),
+	CLK(spiclk, NULL, "spi"),
 };
 
 int __init clk_init(void)
diff --git a/arch/blackfin/mach-bf609/include/mach/anomaly.h b/arch/blackfin/mach-bf609/include/mach/anomaly.h
index 7a07374308a..696786e9a53 100644
--- a/arch/blackfin/mach-bf609/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf609/include/mach/anomaly.h
@@ -23,11 +23,11 @@
 /* TRU_STAT.ADDRERR and TRU_ERRADDR.ADDR May Not Reflect the Correct Status */
 #define ANOMALY_16000003 (1)
 /* The EPPI Data Enable (DEN) Signal is Not Functional */
-#define ANOMALY_16000004 (1)
+#define ANOMALY_16000004 (__SILICON_REVISION__ < 1)
 /* Using L1 Instruction Cache with Parity Enabled is Unreliable */
-#define ANOMALY_16000005 (1)
+#define ANOMALY_16000005 (__SILICON_REVISION__ < 1)
 /* SEQSTAT.SYSNMI Clears Upon Entering the NMI ISR */
-#define ANOMALY_16000006 (1)
+#define ANOMALY_16000006 (__SILICON_REVISION__ < 1)
 /* DDR2 Memory Reads May Fail Intermittently */
 #define ANOMALY_16000007 (1)
 /* Instruction Memory Stalls Can Cause IFLUSH to Fail */
@@ -49,19 +49,53 @@
 /* Speculative Fetches Can Cause Undesired External FIFO Operations */
 #define ANOMALY_16000017 (1)
 /* RSI Boot Cleanup Routine Does Not Clear Registers */
-#define ANOMALY_16000018 (1)
+#define ANOMALY_16000018 (__SILICON_REVISION__ < 1)
 /* SPI Master Boot Device Auto-detection Frequency is Set Incorrectly */
-#define ANOMALY_16000019 (1)
+#define ANOMALY_16000019 (__SILICON_REVISION__ < 1)
 /* rom_SysControl() Fails to Set DDR0_CTL.INIT for Wakeup From Hibernate */
-#define ANOMALY_16000020 (1)
+#define ANOMALY_16000020 (__SILICON_REVISION__ < 1)
 /* rom_SysControl() Fails to Save and Restore DDR0_PHYCTL3 for Hibernate/Wakeup Sequence */
-#define ANOMALY_16000021 (1)
+#define ANOMALY_16000021 (__SILICON_REVISION__ < 1)
 /* Boot Code Fails to Enable Parity Fault Detection */
-#define ANOMALY_16000022 (1)
+#define ANOMALY_16000022 (__SILICON_REVISION__ < 1)
+/* Rom_SysControl Does not Update CGU0_CLKOUTSEL */
+#define ANOMALY_16000023 (__SILICON_REVISION__ < 1)
+/* Spurious Fault Signaled After Clearing an Externally Generated Fault */
+#define ANOMALY_16000024 (1)
+/* SPORT May Drive Data Pins During Inactive Channels in Multichannel Mode */
+#define ANOMALY_16000025 (1)
 /* USB DMA interrupt status do not show the DMA channel interrupt in the DMA ISR */
-#define ANOMALY_16000027 (1)
+#define ANOMALY_16000027 (__SILICON_REVISION__ < 1)
+/* Default SPI Master Boot Mode Setting is Incorrect */
+#define ANOMALY_16000028 (__SILICON_REVISION__ < 1)
+/* PPI tDFSPI Timing Does Not Meet Data Sheet Specification */
+#define ANOMALY_16000027 (__SILICON_REVISION__ < 1)
 /* Interrupted Core Reads of MMRs May Cause Data Loss */
-#define ANOMALY_16000030 (1)
+#define ANOMALY_16000030 (__SILICON_REVISION__ < 1)
+/* Incorrect Default USB_PLL_OSC.PLLM Value */
+#define ANOMALY_16000031 (__SILICON_REVISION__ < 1)
+/* Core Reads of System MMRs May Cause the Core to Hang */
+#define ANOMALY_16000032 (__SILICON_REVISION__ < 1)
+/* PPI Data Underflow on First Word Not Reported in Certain Modes */
+#define ANOMALY_16000033 (1)
+/* CNV1 Red Pixel Substitution feature not functional in the PVP */
+#define ANOMALY_16000034 (__SILICON_REVISION__ < 1)
+/* IPF0 Output Port Color Separation feature not functional */
+#define ANOMALY_16000035 (__SILICON_REVISION__ < 1)
+/* Spurious USB Wake From Hibernate May Occur When USB_VBUS is Low */
+#define ANOMALY_16000036 (__SILICON_REVISION__ < 1)
+/* Core RAISE 2 Instruction Not Latched When Executed at Priority Level 0, 1, or 2 */
+#define ANOMALY_16000037 (__SILICON_REVISION__ < 1)
+/* Spurious Unhandled NMI or L1 Memory Parity Error Interrupt May Occur Upon Entering the NMI ISR */
+#define ANOMALY_16000038 (__SILICON_REVISION__ < 1)
+/* CGU_STAT.PLOCKERR Bit May be Unreliable */
+#define ANOMALY_16000039 (1)
+/* JTAG Emulator Reads of SDU_IDCODE Alter Register Contents */
+#define ANOMALY_16000040 (1)
+/* IFLUSH Instruction Causes Parity Error When Parity Is Enabled */
+#define ANOMALY_16000041 (1)
+/* Instruction Cache Failure When Parity Is Enabled */
+#define ANOMALY_16000042 (__SILICON_REVISION__ == 1)
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000158 (0)
diff --git a/arch/blackfin/mach-bf609/include/mach/defBF60x_base.h b/arch/blackfin/mach-bf609/include/mach/defBF60x_base.h
index f1a6afae1a7..35caa7bc192 100644
--- a/arch/blackfin/mach-bf609/include/mach/defBF60x_base.h
+++ b/arch/blackfin/mach-bf609/include/mach/defBF60x_base.h
@@ -839,6 +839,16 @@
 #define PORTG_LOCK                  0xFFC03344         /* PORTG Port x GPIO Lock Register */
 #define PORTG_REVID                 0xFFC0337C         /* PORTG Port x GPIO Revision ID */
 
+/* ==================================================
+        Pads Controller Registers
+   ================================================== */
+
+/* =========================
+        PADS0
+   ========================= */
+#define PADS0_EMAC_PTP_CLKSEL	    0xFFC03404         /* PADS0 Clock Selection for EMAC and PTP */
+#define PADS0_TWI_VSEL		    0xFFC03408         /* PADS0 TWI Voltage Selection */
+#define PADS0_PORTS_HYST	    0xFFC03440         /* PADS0 Hysteresis Enable Register */
 
 /* =========================
         PINT Registers
diff --git a/arch/blackfin/mach-bf609/include/mach/gpio.h b/arch/blackfin/mach-bf609/include/mach/gpio.h
index c32c8cc8db2..07182513e79 100644
--- a/arch/blackfin/mach-bf609/include/mach/gpio.h
+++ b/arch/blackfin/mach-bf609/include/mach/gpio.h
@@ -152,14 +152,6 @@ struct gpio_port_t {
 	unsigned long revid;
 };
 
-struct gpio_port_s {
-	unsigned short fer;
-	unsigned short data;
-	unsigned short dir;
-	unsigned short inen;
-	unsigned int mux;
-};
-
 #endif
 
 #include <mach-common/ports-a.h>
diff --git a/arch/blackfin/mach-bf609/include/mach/irq.h b/arch/blackfin/mach-bf609/include/mach/irq.h
index fa0843d5d77..d1cb6a86f80 100644
--- a/arch/blackfin/mach-bf609/include/mach/irq.h
+++ b/arch/blackfin/mach-bf609/include/mach/irq.h
@@ -298,7 +298,7 @@
 extern u8 sec_int_priority[];
 
 /*
- * bfin pint registers layout
+ * gpio pint registers layout
  */
 struct bfin_pint_regs {
 	u32 mask_set;
diff --git a/arch/blackfin/mach-bf609/include/mach/pm.h b/arch/blackfin/mach-bf609/include/mach/pm.h
index 3ca0fb96563..a1efd936dd3 100644
--- a/arch/blackfin/mach-bf609/include/mach/pm.h
+++ b/arch/blackfin/mach-bf609/include/mach/pm.h
@@ -10,6 +10,7 @@
 #define __MACH_BF609_PM_H__
 
 #include <linux/suspend.h>
+#include <linux/platform_device.h>
 
 extern int bfin609_pm_enter(suspend_state_t state);
 extern int bf609_pm_prepare(void);
@@ -19,6 +20,6 @@ void bf609_hibernate(void);
 void bfin_sec_raise_irq(unsigned int sid);
 void coreb_enable(void);
 
-int bf609_nor_flash_init(void);
-void bf609_nor_flash_exit(void);
+int bf609_nor_flash_init(struct platform_device *pdev);
+void bf609_nor_flash_exit(struct platform_device *pdev);
 #endif
diff --git a/arch/blackfin/mach-bf609/include/mach/portmux.h b/arch/blackfin/mach-bf609/include/mach/portmux.h
index 2e1a51c2509..c48bb71a55c 100644
--- a/arch/blackfin/mach-bf609/include/mach/portmux.h
+++ b/arch/blackfin/mach-bf609/include/mach/portmux.h
@@ -7,8 +7,6 @@
 #ifndef _MACH_PORTMUX_H_
 #define _MACH_PORTMUX_H_
 
-#define MAX_RESOURCES	MAX_BLACKFIN_GPIOS
-
 /* EMAC RMII Port Mux */
 #define P_MII0_MDC	(P_DEFINED | P_IDENT(GPIO_PC6) | P_FUNCT(0))
 #define P_MII0_MDIO	(P_DEFINED | P_IDENT(GPIO_PC7) | P_FUNCT(0))
@@ -21,6 +19,7 @@
 #define P_MII0_CRS	(P_DEFINED | P_IDENT(GPIO_PC5) | P_FUNCT(0))
 #define P_MII0_ERxER	(P_DEFINED | P_IDENT(GPIO_PC4) | P_FUNCT(0))
 #define P_MII0_TxCLK	(P_DEFINED | P_IDENT(GPIO_PB14) | P_FUNCT(0))
+#define P_MII0_PTPPPS	(P_DEFINED | P_IDENT(GPIO_PB15) | P_FUNCT(0))
 
 #define P_RMII0 {\
 	P_MII0_ETxD0, \
@@ -32,6 +31,7 @@
 	P_MII0_TxCLK, \
 	P_MII0_PHYINT, \
 	P_MII0_CRS, \
+	P_MII0_PTPPPS, \
 	P_MII0_MDC, \
 	P_MII0_MDIO, 0}
 
@@ -46,6 +46,7 @@
 #define P_MII1_CRS	(P_DEFINED | P_IDENT(GPIO_PE13) | P_FUNCT(0))
 #define P_MII1_ERxER	(P_DEFINED | P_IDENT(GPIO_PE14) | P_FUNCT(0))
 #define P_MII1_TxCLK	(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(0))
+#define P_MII1_PTPPPS	(P_DEFINED | P_IDENT(GPIO_PC9) | P_FUNCT(0))
 
 #define P_RMII1 {\
 	P_MII1_ETxD0, \
@@ -57,6 +58,7 @@
 	P_MII1_TxCLK, \
 	P_MII1_PHYINT, \
 	P_MII1_CRS, \
+	P_MII1_PTPPPS, \
 	P_MII1_MDC, \
 	P_MII1_MDIO, 0}
 
diff --git a/arch/blackfin/mach-bf609/pm.c b/arch/blackfin/mach-bf609/pm.c
index ad505d9db4a..b1bfcf434d1 100644
--- a/arch/blackfin/mach-bf609/pm.c
+++ b/arch/blackfin/mach-bf609/pm.c
@@ -210,7 +210,7 @@ void bf609_cpu_pm_enter(suspend_state_t state)
 
 #ifdef CONFIG_PM_BFIN_WAKE_PB15
 	wakeup |= PB15WE;
-# if CONFIG_PM_BFIN_WAKE_PA15_POL
+# if CONFIG_PM_BFIN_WAKE_PB15_POL
 	wakeup_pol |= PB15WE;
 # endif
 #endif
@@ -291,13 +291,13 @@ static struct bfin_cpu_pm_fns bf609_cpu_pm = {
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 static int smc_pm_syscore_suspend(void)
 {
-	bf609_nor_flash_exit();
+	bf609_nor_flash_exit(NULL);
 	return 0;
 }
 
 static void smc_pm_syscore_resume(void)
 {
-	bf609_nor_flash_init();
+	bf609_nor_flash_init(NULL);
 }
 
 static struct syscore_ops smc_pm_syscore_ops = {
diff --git a/arch/blackfin/mach-bf609/scb.c b/arch/blackfin/mach-bf609/scb.c
new file mode 100644
index 00000000000..ac1f07c3359
--- /dev/null
+++ b/arch/blackfin/mach-bf609/scb.c
@@ -0,0 +1,363 @@
+/*
+ * arch/blackfin/mach-common/scb-init.c - reprogram system cross bar priority
+ *
+ * Copyright 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <asm/blackfin.h>
+#include <asm/scb.h>
+
+struct scb_mi_prio scb_data[] = {
+#ifdef CONFIG_SCB0_MI0
+	{ REG_SCB0_ARBR0, REG_SCB0_ARBW0, 32, {
+		CONFIG_SCB0_MI0_SLOT0,
+		CONFIG_SCB0_MI0_SLOT1,
+		CONFIG_SCB0_MI0_SLOT2,
+		CONFIG_SCB0_MI0_SLOT3,
+		CONFIG_SCB0_MI0_SLOT4,
+		CONFIG_SCB0_MI0_SLOT5,
+		CONFIG_SCB0_MI0_SLOT6,
+		CONFIG_SCB0_MI0_SLOT7,
+		CONFIG_SCB0_MI0_SLOT8,
+		CONFIG_SCB0_MI0_SLOT9,
+		CONFIG_SCB0_MI0_SLOT10,
+		CONFIG_SCB0_MI0_SLOT11,
+		CONFIG_SCB0_MI0_SLOT12,
+		CONFIG_SCB0_MI0_SLOT13,
+		CONFIG_SCB0_MI0_SLOT14,
+		CONFIG_SCB0_MI0_SLOT15,
+		CONFIG_SCB0_MI0_SLOT16,
+		CONFIG_SCB0_MI0_SLOT17,
+		CONFIG_SCB0_MI0_SLOT18,
+		CONFIG_SCB0_MI0_SLOT19,
+		CONFIG_SCB0_MI0_SLOT20,
+		CONFIG_SCB0_MI0_SLOT21,
+		CONFIG_SCB0_MI0_SLOT22,
+		CONFIG_SCB0_MI0_SLOT23,
+		CONFIG_SCB0_MI0_SLOT24,
+		CONFIG_SCB0_MI0_SLOT25,
+		CONFIG_SCB0_MI0_SLOT26,
+		CONFIG_SCB0_MI0_SLOT27,
+		CONFIG_SCB0_MI0_SLOT28,
+		CONFIG_SCB0_MI0_SLOT29,
+		CONFIG_SCB0_MI0_SLOT30,
+		CONFIG_SCB0_MI0_SLOT31
+		},
+	},
+#endif
+#ifdef CONFIG_SCB0_MI1
+	{ REG_SCB0_ARBR1, REG_SCB0_ARBW1, 32, {
+		CONFIG_SCB0_MI1_SLOT0,
+		CONFIG_SCB0_MI1_SLOT1,
+		CONFIG_SCB0_MI1_SLOT2,
+		CONFIG_SCB0_MI1_SLOT3,
+		CONFIG_SCB0_MI1_SLOT4,
+		CONFIG_SCB0_MI1_SLOT5,
+		CONFIG_SCB0_MI1_SLOT6,
+		CONFIG_SCB0_MI1_SLOT7,
+		CONFIG_SCB0_MI1_SLOT8,
+		CONFIG_SCB0_MI1_SLOT9,
+		CONFIG_SCB0_MI1_SLOT10,
+		CONFIG_SCB0_MI1_SLOT11,
+		CONFIG_SCB0_MI1_SLOT12,
+		CONFIG_SCB0_MI1_SLOT13,
+		CONFIG_SCB0_MI1_SLOT14,
+		CONFIG_SCB0_MI1_SLOT15,
+		CONFIG_SCB0_MI1_SLOT16,
+		CONFIG_SCB0_MI1_SLOT17,
+		CONFIG_SCB0_MI1_SLOT18,
+		CONFIG_SCB0_MI1_SLOT19,
+		CONFIG_SCB0_MI1_SLOT20,
+		CONFIG_SCB0_MI1_SLOT21,
+		CONFIG_SCB0_MI1_SLOT22,
+		CONFIG_SCB0_MI1_SLOT23,
+		CONFIG_SCB0_MI1_SLOT24,
+		CONFIG_SCB0_MI1_SLOT25,
+		CONFIG_SCB0_MI1_SLOT26,
+		CONFIG_SCB0_MI1_SLOT27,
+		CONFIG_SCB0_MI1_SLOT28,
+		CONFIG_SCB0_MI1_SLOT29,
+		CONFIG_SCB0_MI1_SLOT30,
+		CONFIG_SCB0_MI1_SLOT31
+		},
+	},
+#endif
+#ifdef CONFIG_SCB0_MI2
+	{ REG_SCB0_ARBR2, REG_SCB0_ARBW2, 32, {
+		CONFIG_SCB0_MI2_SLOT0,
+		CONFIG_SCB0_MI2_SLOT1,
+		CONFIG_SCB0_MI2_SLOT2,
+		CONFIG_SCB0_MI2_SLOT3,
+		CONFIG_SCB0_MI2_SLOT4,
+		CONFIG_SCB0_MI2_SLOT5,
+		CONFIG_SCB0_MI2_SLOT6,
+		CONFIG_SCB0_MI2_SLOT7,
+		CONFIG_SCB0_MI2_SLOT8,
+		CONFIG_SCB0_MI2_SLOT9,
+		CONFIG_SCB0_MI2_SLOT10,
+		CONFIG_SCB0_MI2_SLOT11,
+		CONFIG_SCB0_MI2_SLOT12,
+		CONFIG_SCB0_MI2_SLOT13,
+		CONFIG_SCB0_MI2_SLOT14,
+		CONFIG_SCB0_MI2_SLOT15,
+		CONFIG_SCB0_MI2_SLOT16,
+		CONFIG_SCB0_MI2_SLOT17,
+		CONFIG_SCB0_MI2_SLOT18,
+		CONFIG_SCB0_MI2_SLOT19,
+		CONFIG_SCB0_MI2_SLOT20,
+		CONFIG_SCB0_MI2_SLOT21,
+		CONFIG_SCB0_MI2_SLOT22,
+		CONFIG_SCB0_MI2_SLOT23,
+		CONFIG_SCB0_MI2_SLOT24,
+		CONFIG_SCB0_MI2_SLOT25,
+		CONFIG_SCB0_MI2_SLOT26,
+		CONFIG_SCB0_MI2_SLOT27,
+		CONFIG_SCB0_MI2_SLOT28,
+		CONFIG_SCB0_MI2_SLOT29,
+		CONFIG_SCB0_MI2_SLOT30,
+		CONFIG_SCB0_MI2_SLOT31
+		},
+	},
+#endif
+#ifdef CONFIG_SCB0_MI3
+	{ REG_SCB0_ARBR3, REG_SCB0_ARBW3, 32, {
+		CONFIG_SCB0_MI3_SLOT0,
+		CONFIG_SCB0_MI3_SLOT1,
+		CONFIG_SCB0_MI3_SLOT2,
+		CONFIG_SCB0_MI3_SLOT3,
+		CONFIG_SCB0_MI3_SLOT4,
+		CONFIG_SCB0_MI3_SLOT5,
+		CONFIG_SCB0_MI3_SLOT6,
+		CONFIG_SCB0_MI3_SLOT7,
+		CONFIG_SCB0_MI3_SLOT8,
+		CONFIG_SCB0_MI3_SLOT9,
+		CONFIG_SCB0_MI3_SLOT10,
+		CONFIG_SCB0_MI3_SLOT11,
+		CONFIG_SCB0_MI3_SLOT12,
+		CONFIG_SCB0_MI3_SLOT13,
+		CONFIG_SCB0_MI3_SLOT14,
+		CONFIG_SCB0_MI3_SLOT15,
+		CONFIG_SCB0_MI3_SLOT16,
+		CONFIG_SCB0_MI3_SLOT17,
+		CONFIG_SCB0_MI3_SLOT18,
+		CONFIG_SCB0_MI3_SLOT19,
+		CONFIG_SCB0_MI3_SLOT20,
+		CONFIG_SCB0_MI3_SLOT21,
+		CONFIG_SCB0_MI3_SLOT22,
+		CONFIG_SCB0_MI3_SLOT23,
+		CONFIG_SCB0_MI3_SLOT24,
+		CONFIG_SCB0_MI3_SLOT25,
+		CONFIG_SCB0_MI3_SLOT26,
+		CONFIG_SCB0_MI3_SLOT27,
+		CONFIG_SCB0_MI3_SLOT28,
+		CONFIG_SCB0_MI3_SLOT29,
+		CONFIG_SCB0_MI3_SLOT30,
+		CONFIG_SCB0_MI3_SLOT31
+		},
+	},
+#endif
+#ifdef CONFIG_SCB0_MI4
+	{ REG_SCB0_ARBR4, REG_SCB4_ARBW0, 32, {
+		CONFIG_SCB0_MI4_SLOT0,
+		CONFIG_SCB0_MI4_SLOT1,
+		CONFIG_SCB0_MI4_SLOT2,
+		CONFIG_SCB0_MI4_SLOT3,
+		CONFIG_SCB0_MI4_SLOT4,
+		CONFIG_SCB0_MI4_SLOT5,
+		CONFIG_SCB0_MI4_SLOT6,
+		CONFIG_SCB0_MI4_SLOT7,
+		CONFIG_SCB0_MI4_SLOT8,
+		CONFIG_SCB0_MI4_SLOT9,
+		CONFIG_SCB0_MI4_SLOT10,
+		CONFIG_SCB0_MI4_SLOT11,
+		CONFIG_SCB0_MI4_SLOT12,
+		CONFIG_SCB0_MI4_SLOT13,
+		CONFIG_SCB0_MI4_SLOT14,
+		CONFIG_SCB0_MI4_SLOT15,
+		CONFIG_SCB0_MI4_SLOT16,
+		CONFIG_SCB0_MI4_SLOT17,
+		CONFIG_SCB0_MI4_SLOT18,
+		CONFIG_SCB0_MI4_SLOT19,
+		CONFIG_SCB0_MI4_SLOT20,
+		CONFIG_SCB0_MI4_SLOT21,
+		CONFIG_SCB0_MI4_SLOT22,
+		CONFIG_SCB0_MI4_SLOT23,
+		CONFIG_SCB0_MI4_SLOT24,
+		CONFIG_SCB0_MI4_SLOT25,
+		CONFIG_SCB0_MI4_SLOT26,
+		CONFIG_SCB0_MI4_SLOT27,
+		CONFIG_SCB0_MI4_SLOT28,
+		CONFIG_SCB0_MI4_SLOT29,
+		CONFIG_SCB0_MI4_SLOT30,
+		CONFIG_SCB0_MI4_SLOT31
+		},
+	},
+#endif
+#ifdef CONFIG_SCB0_MI5
+	{ REG_SCB0_ARBR5, REG_SCB0_ARBW5, 16, {
+		CONFIG_SCB0_MI5_SLOT0,
+		CONFIG_SCB0_MI5_SLOT1,
+		CONFIG_SCB0_MI5_SLOT2,
+		CONFIG_SCB0_MI5_SLOT3,
+		CONFIG_SCB0_MI5_SLOT4,
+		CONFIG_SCB0_MI5_SLOT5,
+		CONFIG_SCB0_MI5_SLOT6,
+		CONFIG_SCB0_MI5_SLOT7,
+		CONFIG_SCB0_MI5_SLOT8,
+		CONFIG_SCB0_MI5_SLOT9,
+		CONFIG_SCB0_MI5_SLOT10,
+		CONFIG_SCB0_MI5_SLOT11,
+		CONFIG_SCB0_MI5_SLOT12,
+		CONFIG_SCB0_MI5_SLOT13,
+		CONFIG_SCB0_MI5_SLOT14,
+		CONFIG_SCB0_MI5_SLOT15
+		},
+	},
+#endif
+#ifdef CONFIG_SCB1_MI0
+	{ REG_SCB1_ARBR0, REG_SCB1_ARBW0, 20, {
+		CONFIG_SCB1_MI0_SLOT0,
+		CONFIG_SCB1_MI0_SLOT1,
+		CONFIG_SCB1_MI0_SLOT2,
+		CONFIG_SCB1_MI0_SLOT3,
+		CONFIG_SCB1_MI0_SLOT4,
+		CONFIG_SCB1_MI0_SLOT5,
+		CONFIG_SCB1_MI0_SLOT6,
+		CONFIG_SCB1_MI0_SLOT7,
+		CONFIG_SCB1_MI0_SLOT8,
+		CONFIG_SCB1_MI0_SLOT9,
+		CONFIG_SCB1_MI0_SLOT10,
+		CONFIG_SCB1_MI0_SLOT11,
+		CONFIG_SCB1_MI0_SLOT12,
+		CONFIG_SCB1_MI0_SLOT13,
+		CONFIG_SCB1_MI0_SLOT14,
+		CONFIG_SCB1_MI0_SLOT15,
+		CONFIG_SCB1_MI0_SLOT16,
+		CONFIG_SCB1_MI0_SLOT17,
+		CONFIG_SCB1_MI0_SLOT18,
+		CONFIG_SCB1_MI0_SLOT19
+		},
+	},
+#endif
+#ifdef CONFIG_SCB2_MI0
+	{ REG_SCB2_ARBR0, REG_SCB2_ARBW0, 10, {
+		CONFIG_SCB2_MI0_SLOT0,
+		CONFIG_SCB2_MI0_SLOT1,
+		CONFIG_SCB2_MI0_SLOT2,
+		CONFIG_SCB2_MI0_SLOT3,
+		CONFIG_SCB2_MI0_SLOT4,
+		CONFIG_SCB2_MI0_SLOT5,
+		CONFIG_SCB2_MI0_SLOT6,
+		CONFIG_SCB2_MI0_SLOT7,
+		CONFIG_SCB2_MI0_SLOT8,
+		CONFIG_SCB2_MI0_SLOT9
+		},
+	},
+#endif
+#ifdef CONFIG_SCB3_MI0
+	{ REG_SCB3_ARBR0, REG_SCB3_ARBW0, 16, {
+		CONFIG_SCB3_MI0_SLOT0,
+		CONFIG_SCB3_MI0_SLOT1,
+		CONFIG_SCB3_MI0_SLOT2,
+		CONFIG_SCB3_MI0_SLOT3,
+		CONFIG_SCB3_MI0_SLOT4,
+		CONFIG_SCB3_MI0_SLOT5,
+		CONFIG_SCB3_MI0_SLOT6,
+		CONFIG_SCB3_MI0_SLOT7,
+		CONFIG_SCB3_MI0_SLOT8,
+		CONFIG_SCB3_MI0_SLOT9,
+		CONFIG_SCB3_MI0_SLOT10,
+		CONFIG_SCB3_MI0_SLOT11,
+		CONFIG_SCB3_MI0_SLOT12,
+		CONFIG_SCB3_MI0_SLOT13,
+		CONFIG_SCB3_MI0_SLOT14,
+		CONFIG_SCB3_MI0_SLOT15
+		},
+	},
+#endif
+#ifdef CONFIG_SCB4_MI0
+	{ REG_SCB4_ARBR0, REG_SCB4_ARBW0, 16, {
+		CONFIG_SCB4_MI0_SLOT0,
+		CONFIG_SCB4_MI0_SLOT1,
+		CONFIG_SCB4_MI0_SLOT2,
+		CONFIG_SCB4_MI0_SLOT3,
+		CONFIG_SCB4_MI0_SLOT4,
+		CONFIG_SCB4_MI0_SLOT5,
+		CONFIG_SCB4_MI0_SLOT6,
+		CONFIG_SCB4_MI0_SLOT7,
+		CONFIG_SCB4_MI0_SLOT8,
+		CONFIG_SCB4_MI0_SLOT9,
+		CONFIG_SCB4_MI0_SLOT10,
+		CONFIG_SCB4_MI0_SLOT11,
+		CONFIG_SCB4_MI0_SLOT12,
+		CONFIG_SCB4_MI0_SLOT13,
+		CONFIG_SCB4_MI0_SLOT14,
+		CONFIG_SCB4_MI0_SLOT15
+		},
+	},
+#endif
+#ifdef CONFIG_SCB5_MI0
+	{ REG_SCB5_ARBR0, REG_SCB5_ARBW0, 8, {
+		CONFIG_SCB5_MI0_SLOT0,
+		CONFIG_SCB5_MI0_SLOT1,
+		CONFIG_SCB5_MI0_SLOT2,
+		CONFIG_SCB5_MI0_SLOT3,
+		CONFIG_SCB5_MI0_SLOT4,
+		CONFIG_SCB5_MI0_SLOT5,
+		CONFIG_SCB5_MI0_SLOT6,
+		CONFIG_SCB5_MI0_SLOT7
+		},
+	},
+#endif
+#ifdef CONFIG_SCB6_MI0
+	{ REG_SCB6_ARBR0, REG_SCB6_ARBW0, 4, {
+		CONFIG_SCB6_MI0_SLOT0,
+		CONFIG_SCB6_MI0_SLOT1,
+		CONFIG_SCB6_MI0_SLOT2,
+		CONFIG_SCB6_MI0_SLOT3
+		},
+	},
+#endif
+#ifdef CONFIG_SCB7_MI0
+	{ REG_SCB7_ARBR0, REG_SCB7_ARBW0, 6, {
+		CONFIG_SCB7_MI0_SLOT0,
+		CONFIG_SCB7_MI0_SLOT1,
+		CONFIG_SCB7_MI0_SLOT2,
+		CONFIG_SCB7_MI0_SLOT3,
+		CONFIG_SCB7_MI0_SLOT4,
+		CONFIG_SCB7_MI0_SLOT5
+		},
+	},
+#endif
+#ifdef CONFIG_SCB8_MI0
+	{ REG_SCB8_ARBR0, REG_SCB8_ARBW0, 8, {
+		CONFIG_SCB8_MI0_SLOT0,
+		CONFIG_SCB8_MI0_SLOT1,
+		CONFIG_SCB8_MI0_SLOT2,
+		CONFIG_SCB8_MI0_SLOT3,
+		CONFIG_SCB8_MI0_SLOT4,
+		CONFIG_SCB8_MI0_SLOT5,
+		CONFIG_SCB8_MI0_SLOT6,
+		CONFIG_SCB8_MI0_SLOT7
+		},
+	},
+#endif
+#ifdef CONFIG_SCB9_MI0
+	{ REG_SCB9_ARBR0, REG_SCB9_ARBW0, 10, {
+		CONFIG_SCB9_MI0_SLOT0,
+		CONFIG_SCB9_MI0_SLOT1,
+		CONFIG_SCB9_MI0_SLOT2,
+		CONFIG_SCB9_MI0_SLOT3,
+		CONFIG_SCB9_MI0_SLOT4,
+		CONFIG_SCB9_MI0_SLOT5,
+		CONFIG_SCB9_MI0_SLOT6,
+		CONFIG_SCB9_MI0_SLOT7,
+		CONFIG_SCB9_MI0_SLOT8,
+		CONFIG_SCB9_MI0_SLOT9
+		},
+	},
+#endif
+	{ 0, }
+};