aboutsummaryrefslogtreecommitdiff
path: root/arch/blackfin/mach-bf561
diff options
context:
space:
mode:
Diffstat (limited to 'arch/blackfin/mach-bf561')
-rw-r--r--arch/blackfin/mach-bf561/atomic.S7
-rw-r--r--arch/blackfin/mach-bf561/boards/acvilon.c48
-rw-r--r--arch/blackfin/mach-bf561/boards/cm_bf561.c122
-rw-r--r--arch/blackfin/mach-bf561/boards/ezkit.c229
-rw-r--r--arch/blackfin/mach-bf561/boards/tepla.c15
-rw-r--r--arch/blackfin/mach-bf561/include/mach/anomaly.h136
-rw-r--r--arch/blackfin/mach-bf561/include/mach/defBF561.h229
-rw-r--r--arch/blackfin/mach-bf561/include/mach/gpio.h6
-rw-r--r--arch/blackfin/mach-bf561/include/mach/pll.h4
-rw-r--r--arch/blackfin/mach-bf561/secondary.S152
-rw-r--r--arch/blackfin/mach-bf561/smp.c18
11 files changed, 531 insertions, 435 deletions
diff --git a/arch/blackfin/mach-bf561/atomic.S b/arch/blackfin/mach-bf561/atomic.S
index 52d6f73fcce..2a08df8e8c4 100644
--- a/arch/blackfin/mach-bf561/atomic.S
+++ b/arch/blackfin/mach-bf561/atomic.S
@@ -72,6 +72,13 @@ ENTRY(_get_core_lock_noflush)
SSYNC(r2);
jump .Lretry_corelock_noflush
.Ldone_corelock_noflush:
+ /*
+ * SMP kgdb runs into dead loop without NOP here, when one core
+ * single steps over get_core_lock_noflush and the other executes
+ * get_core_lock as a slave node.
+ */
+ nop;
+ CSYNC(r2);
rts;
ENDPROC(_get_core_lock_noflush)
diff --git a/arch/blackfin/mach-bf561/boards/acvilon.c b/arch/blackfin/mach-bf561/boards/acvilon.c
index 9231a942892..6ab951534d7 100644
--- a/arch/blackfin/mach-bf561/boards/acvilon.c
+++ b/arch/blackfin/mach-bf561/boards/acvilon.c
@@ -44,6 +44,7 @@
#include <linux/spi/flash.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
+#include <linux/gpio.h>
#include <linux/jiffies.h>
#include <linux/i2c-pca-platform.h>
#include <linux/delay.h>
@@ -60,7 +61,7 @@
*/
const char bfin_board_name[] = "Acvilon board";
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
@@ -137,7 +138,7 @@ static struct i2c_board_info acvilon_i2c_devs[] __initdata = {
},
};
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
static struct platdata_mtd_ram mtd_ram_data = {
.mapname = "rootfs(RAM)",
.bankwidth = 4,
@@ -160,7 +161,7 @@ static struct platform_device mtd_ram_device = {
};
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
{
@@ -194,7 +195,7 @@ static struct platform_device smsc911x_device = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
@@ -203,8 +204,13 @@ static struct resource bfin_uart0_resources[] = {
.flags = IORESOURCE_MEM,
},
{
+ .start = IRQ_UART_TX,
+ .end = IRQ_UART_TX,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
.start = IRQ_UART_RX,
- .end = IRQ_UART_RX + 1,
+ .end = IRQ_UART_RX,
.flags = IORESOURCE_IRQ,
},
{
@@ -241,9 +247,7 @@ static struct platform_device bfin_uart0_device = {
#endif
#endif
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
-
-const char *part_probes[] = { "cmdlinepart", NULL };
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
static struct mtd_partition bfin_plat_nand_partitions[] = {
{
@@ -284,7 +288,6 @@ static struct platform_nand_data bfin_plat_nand_data = {
.chip = {
.nr_chips = 1,
.chip_delay = 30,
- .part_probe_types = part_probes,
.partitions = bfin_plat_nand_partitions,
.nr_partitions = ARRAY_SIZE(bfin_plat_nand_partitions),
},
@@ -321,7 +324,7 @@ static void bfin_plat_nand_init(void)
}
#endif
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
static struct mtd_partition bfin_spi_dataflash_partitions[] = {
{
.name = "bootloader",
@@ -364,18 +367,10 @@ static struct flash_platform_data bfin_spi_dataflash_data = {
/* DataFlash chip */
static struct bfin5xx_spi_chip data_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip */
- .bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 8,
};
#endif
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
@@ -414,16 +409,15 @@ static struct platform_device bfin_spi0_device = {
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 3,
- .controller_data = &spidev_chip_info,
},
#endif
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.max_speed_hz = 33250000, /* max spi clock (SCK) speed in HZ */
@@ -479,11 +473,11 @@ static struct platform_device bfin_dpmc = {
static struct platform_device *acvilon_devices[] __initdata = {
&bfin_dpmc,
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
@@ -491,17 +485,17 @@ static struct platform_device *acvilon_devices[] __initdata = {
&bfin_gpios_device,
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
&bfin_i2c_pca_device,
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
&bfin_async_nand_device,
#endif
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
&mtd_ram_device,
#endif
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 87595cd38af..e862f7823e6 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -13,11 +13,12 @@
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/ata_platform.h>
#include <linux/irq.h>
+#include <linux/gpio.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
@@ -29,10 +30,10 @@
*/
const char bfin_board_name[] = "Bluetechnix CM BF561";
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
@@ -60,34 +61,11 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
- .bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
- .enable_dma = 1, /* use dma transfer with this chip*/
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip mmc_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
@@ -100,33 +78,20 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
- {
- .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
- .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0, /* Framework bus number */
- .chip_select = 1, /* Framework chip select. */
- .platform_data = NULL, /* No spi_driver specific config */
- .controller_data = &spi_adc_chip_info,
- },
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
- .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
@@ -170,14 +135,14 @@ static struct platform_device bfin_spi0_device = {
#endif /* spi master and devices */
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
static struct platform_device hitachi_fb_device = {
.name = "hitachi-tx09",
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
@@ -209,7 +174,7 @@ static struct platform_device smc91x_device = {
};
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
@@ -244,7 +209,7 @@ static struct platform_device smsc911x_device = {
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x24000000,
@@ -265,7 +230,7 @@ static struct platform_device net2272_bfin_device = {
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x24008000,
@@ -304,7 +269,7 @@ static struct platform_device isp1362_hcd_device = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
@@ -313,8 +278,13 @@ static struct resource bfin_uart0_resources[] = {
.flags = IORESOURCE_MEM,
},
{
+ .start = IRQ_UART_TX,
+ .end = IRQ_UART_TX,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
.start = IRQ_UART_RX,
- .end = IRQ_UART_RX+1,
+ .end = IRQ_UART_RX,
.flags = IORESOURCE_IRQ,
},
{
@@ -350,7 +320,7 @@ static struct platform_device bfin_uart0_device = {
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
@@ -379,12 +349,12 @@ static struct platform_device bfin_sir0_device = {
#endif
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
#define PATA_INT IRQ_PF46
static struct pata_platform_info bfin_pata_platform_data = {
.ioport_shift = 2,
- .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+ .irq_type = IRQF_TRIGGER_HIGH,
};
static struct resource bfin_pata_resources[] = {
@@ -416,7 +386,7 @@ static struct platform_device bfin_pata_device = {
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition para_partitions[] = {
{
.name = "bootloader(nor)",
@@ -487,62 +457,84 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
&bfin_dpmc,
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
&hitachi_fb_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
&bfin_pata_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&para_flash_device,
#endif
};
+static int __init net2272_init(void)
+{
+#if IS_ENABLED(CONFIG_USB_NET2272)
+ int ret;
+
+ ret = gpio_request(GPIO_PF46, "net2272");
+ if (ret)
+ return ret;
+
+ /* Reset USB Chip, PF46 */
+ gpio_direction_output(GPIO_PF46, 0);
+ mdelay(2);
+ gpio_set_value(GPIO_PF46, 1);
+#endif
+
+ return 0;
+}
+
static int __init cm_bf561_init(void)
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf561_devices, ARRAY_SIZE(cm_bf561_devices));
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
#endif
+
+ if (net2272_init())
+ pr_warning("unable to configure net2272; it probably won't work\n");
+
return 0;
}
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 5067984a62e..2de71e8c104 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -14,6 +14,7 @@
#include <linux/spi/spi.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
+#include <linux/gpio.h>
#include <linux/delay.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
@@ -25,7 +26,7 @@
*/
const char bfin_board_name[] = "ADI BF561-EZKIT";
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
@@ -60,7 +61,7 @@ static struct platform_device bfin_isp1760_device = {
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
static struct resource isp1362_hcd_resources[] = {
@@ -101,13 +102,16 @@ static struct platform_device isp1362_hcd_device = {
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x2C000000,
.end = 0x2C000000 + 0x7F,
.flags = IORESOURCE_MEM,
}, {
+ .start = 1,
+ .flags = IORESOURCE_BUS,
+ }, {
.start = IRQ_PF10,
.end = IRQ_PF10,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
@@ -126,7 +130,7 @@ static struct platform_device net2272_bfin_device = {
* USB-LAN EzExtender board
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
@@ -160,7 +164,7 @@ static struct platform_device smc91x_device = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
@@ -169,8 +173,13 @@ static struct resource bfin_uart0_resources[] = {
.flags = IORESOURCE_MEM,
},
{
+ .start = IRQ_UART_TX,
+ .end = IRQ_UART_TX,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
.start = IRQ_UART_RX,
- .end = IRQ_UART_RX+1,
+ .end = IRQ_UART_RX,
.flags = IORESOURCE_IRQ,
},
{
@@ -206,7 +215,7 @@ static struct platform_device bfin_uart0_device = {
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
@@ -235,7 +244,7 @@ static struct platform_device bfin_sir0_device = {
#endif
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
@@ -283,22 +292,7 @@ static struct platform_device ezkit_flash_device = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
@@ -337,30 +331,27 @@ static struct platform_device bfin_spi0_device = {
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
- .controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
- .controller_data = &spidev_chip_info,
},
#endif
};
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
@@ -384,7 +375,7 @@ static struct platform_device bfin_device_gpiokeys = {
};
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
@@ -392,7 +383,7 @@ static struct i2c_gpio_platform_data i2c_gpio_data = {
.scl_pin = GPIO_PF0,
.sda_is_open_drain = 0,
.scl_is_open_drain = 0,
- .udelay = 40,
+ .udelay = 10,
};
static struct platform_device i2c_gpio_device = {
@@ -431,23 +422,106 @@ static struct platform_device bfin_dpmc = {
},
};
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
-static struct platform_device bfin_i2s = {
- .name = "bfin-i2s",
- .id = CONFIG_SND_BF5XX_SPORT_NUM,
- /* TODO: add platform data here */
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
+#include <linux/videodev2.h>
+#include <media/blackfin/bfin_capture.h>
+#include <media/blackfin/ppi.h>
+
+static const unsigned short ppi_req[] = {
+ P_PPI0_D0, P_PPI0_D1, P_PPI0_D2, P_PPI0_D3,
+ P_PPI0_D4, P_PPI0_D5, P_PPI0_D6, P_PPI0_D7,
+ P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
+ 0,
+};
+
+static const struct ppi_info ppi_info = {
+ .type = PPI_TYPE_PPI,
+ .dma_ch = CH_PPI0,
+ .irq_err = IRQ_PPI1_ERROR,
+ .base = (void __iomem *)PPI0_CONTROL,
+ .pin_req = ppi_req,
+};
+
+#if IS_ENABLED(CONFIG_VIDEO_ADV7183)
+#include <media/adv7183.h>
+static struct v4l2_input adv7183_inputs[] = {
+ {
+ .index = 0,
+ .name = "Composite",
+ .type = V4L2_INPUT_TYPE_CAMERA,
+ .std = V4L2_STD_ALL,
+ .capabilities = V4L2_IN_CAP_STD,
+ },
+ {
+ .index = 1,
+ .name = "S-Video",
+ .type = V4L2_INPUT_TYPE_CAMERA,
+ .std = V4L2_STD_ALL,
+ .capabilities = V4L2_IN_CAP_STD,
+ },
+ {
+ .index = 2,
+ .name = "Component",
+ .type = V4L2_INPUT_TYPE_CAMERA,
+ .std = V4L2_STD_ALL,
+ .capabilities = V4L2_IN_CAP_STD,
+ },
+};
+
+static struct bcap_route adv7183_routes[] = {
+ {
+ .input = ADV7183_COMPOSITE4,
+ .output = ADV7183_8BIT_OUT,
+ },
+ {
+ .input = ADV7183_SVIDEO0,
+ .output = ADV7183_8BIT_OUT,
+ },
+ {
+ .input = ADV7183_COMPONENT0,
+ .output = ADV7183_8BIT_OUT,
+ },
+};
+
+
+static const unsigned adv7183_gpio[] = {
+ GPIO_PF13, /* reset pin */
+ GPIO_PF2, /* output enable pin */
+};
+
+static struct bfin_capture_config bfin_capture_data = {
+ .card_name = "BF561",
+ .inputs = adv7183_inputs,
+ .num_inputs = ARRAY_SIZE(adv7183_inputs),
+ .routes = adv7183_routes,
+ .i2c_adapter_id = 0,
+ .board_info = {
+ .type = "adv7183",
+ .addr = 0x20,
+ .platform_data = (void *)adv7183_gpio,
+ },
+ .ppi_info = &ppi_info,
+ .ppi_control = (PACK_EN | DLEN_8 | DMA32 | FLD_SEL),
};
#endif
-#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
-static struct platform_device bfin_tdm = {
- .name = "bfin-tdm",
+static struct platform_device bfin_capture_device = {
+ .name = "bfin_capture",
+ .dev = {
+ .platform_data = &bfin_capture_data,
+ },
+};
+#endif
+
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
/* TODO: add platform data here */
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97 = {
.name = "bfin-ac97",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
@@ -455,67 +529,103 @@ static struct platform_device bfin_ac97 = {
};
#endif
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
+static const char * const ad1836_link[] = {
+ "bfin-i2s.0",
+ "spi0.4",
+};
+static struct platform_device bfin_ad1836_machine = {
+ .name = "bfin-snd-ad1836",
+ .id = -1,
+ .dev = {
+ .platform_data = (void *)ad1836_link,
+ },
+};
+#endif
+
static struct platform_device *ezkit_devices[] __initdata = {
&bfin_dpmc,
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
&i2c_gpio_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
- &bfin_i2s,
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
+ &bfin_capture_device,
#endif
-#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
- &bfin_tdm,
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
+ &bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97,
#endif
+
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
+ &bfin_ad1836_machine,
+#endif
};
+static int __init net2272_init(void)
+{
+#if IS_ENABLED(CONFIG_USB_NET2272)
+ int ret;
+
+ ret = gpio_request(GPIO_PF11, "net2272");
+ if (ret)
+ return ret;
+
+ /* Reset the USB chip */
+ gpio_direction_output(GPIO_PF11, 0);
+ mdelay(2);
+ gpio_set_value(GPIO_PF11, 1);
+#endif
+
+ return 0;
+}
+
static int __init ezkit_init(void)
{
int ret;
@@ -526,12 +636,12 @@ static int __init ezkit_init(void)
if (ret < 0)
return ret;
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 12));
SSYNC();
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 15));
bfin_write_FIO0_FLAG_S(1 << 15);
SSYNC();
@@ -542,6 +652,9 @@ static int __init ezkit_init(void)
udelay(400);
#endif
+ if (net2272_init())
+ pr_warning("unable to configure net2272; it probably won't work\n");
+
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
return 0;
}
diff --git a/arch/blackfin/mach-bf561/boards/tepla.c b/arch/blackfin/mach-bf561/boards/tepla.c
index bb056e60f6e..f87b8cc0cd4 100644
--- a/arch/blackfin/mach-bf561/boards/tepla.c
+++ b/arch/blackfin/mach-bf561/boards/tepla.c
@@ -42,7 +42,7 @@ static struct platform_device smc91x_device = {
.resource = smc91x_resources,
};
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
@@ -51,8 +51,13 @@ static struct resource bfin_uart0_resources[] = {
.flags = IORESOURCE_MEM,
},
{
+ .start = IRQ_UART_TX,
+ .end = IRQ_UART_TX,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
.start = IRQ_UART_RX,
- .end = IRQ_UART_RX+1,
+ .end = IRQ_UART_RX,
.flags = IORESOURCE_IRQ,
},
{
@@ -88,7 +93,7 @@ static struct platform_device bfin_uart0_device = {
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
@@ -120,13 +125,13 @@ static struct platform_device bfin_sir0_device = {
static struct platform_device *tepla_devices[] __initdata = {
&smc91x_device,
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
diff --git a/arch/blackfin/mach-bf561/include/mach/anomaly.h b/arch/blackfin/mach-bf561/include/mach/anomaly.h
index 22b5ab77302..038249c1d0d 100644
--- a/arch/blackfin/mach-bf561/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf561/include/mach/anomaly.h
@@ -6,12 +6,11 @@
* DO NOT EDIT THIS FILE
*
* Copyright 2004-2011 Analog Devices Inc.
- * Licensed under the ADI BSD license.
- * https://docs.blackfin.uclinux.org/doku.php?id=adi_bsd
+ * Licensed under the Clear BSD license.
*/
/* This file should be up to date with:
- * - Revision R, 05/25/2010; ADSP-BF561 Blackfin Processor Anomaly List
+ * - Revision S, 05/23/2011; ADSP-BF561 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
@@ -26,62 +25,16 @@
#define ANOMALY_05000074 (1)
/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
-/* Trace Buffers May Contain Errors in Emulation Mode and/or Exception, NMI, Reset Handlers */
-#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
/* TESTSET Instructions Restricted to 32-Bit Aligned Memory Locations */
#define ANOMALY_05000120 (1)
/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
#define ANOMALY_05000122 (1)
-/* Erroneous Exception when Enabling Cache */
-#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
/* SIGNBITS Instruction Not Functional under Certain Conditions */
#define ANOMALY_05000127 (1)
-/* Two bits in the Watchpoint Status Register (WPSTAT) are swapped */
-#define ANOMALY_05000134 (__SILICON_REVISION__ < 3)
-/* Enable wires from the Data Watchpoint Address Control Register (WPDACTL) are swapped */
-#define ANOMALY_05000135 (__SILICON_REVISION__ < 3)
-/* Stall in multi-unit DMA operations */
-#define ANOMALY_05000136 (__SILICON_REVISION__ < 3)
-/* Allowing the SPORT RX FIFO to fill will cause an overflow */
-#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
-/* Infinite Stall may occur with a particular sequence of consecutive dual dag events */
-#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
-/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
-#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
-/* DMA and TESTSET conflict when both are accessing external memory */
-#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
-/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
-#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
-/* MDMA may lose the first few words of a descriptor chain */
-#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
-/* Source MDMA descriptor may stop with a DMA Error near beginning of descriptor fetch */
-#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
/* IMDMA S1/D1 Channel May Stall */
#define ANOMALY_05000149 (1)
-/* DMA engine may lose data due to incorrect handshaking */
-#define ANOMALY_05000150 (__SILICON_REVISION__ < 3)
-/* DMA stalls when all three controllers read data from the same source */
-#define ANOMALY_05000151 (__SILICON_REVISION__ < 3)
-/* Execution stall when executing in L2 and doing external accesses */
-#define ANOMALY_05000152 (__SILICON_REVISION__ < 3)
-/* Frame Delay in SPORT Multichannel Mode */
-#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
-/* SPORT TFS signal stays active in multichannel mode outside of valid channels */
-#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
/* Timers in PWM-Out Mode with PPI GP Receive (Input) Mode with 0 Frame Syncs */
#define ANOMALY_05000156 (__SILICON_REVISION__ < 4)
-/* Killed 32-Bit MMR Write Leads to Next System MMR Access Thinking It Should Be 32-Bit */
-#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
-/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
-#define ANOMALY_05000159 (__SILICON_REVISION__ < 3)
-/* A read from external memory may return a wrong value with data cache enabled */
-#define ANOMALY_05000160 (__SILICON_REVISION__ < 3)
-/* Data Cache Fill data can be corrupted after/during Instruction DMA if certain core stalls exist */
-#define ANOMALY_05000161 (__SILICON_REVISION__ < 3)
-/* DMEM_CONTROL<12> is not set on Reset */
-#define ANOMALY_05000162 (__SILICON_REVISION__ < 3)
-/* SPORT Transmit Data Is Not Gated by External Frame Sync in Certain Conditions */
-#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
/* PPI Data Lengths between 8 and 16 Do Not Zero Out Upper Bits */
#define ANOMALY_05000166 (1)
/* Turning SPORTs on while External Frame Sync Is Active May Corrupt Data */
@@ -92,10 +45,6 @@
#define ANOMALY_05000169 (__SILICON_REVISION__ < 5)
/* Boot-ROM Modifies SICA_IWRx Wakeup Registers */
#define ANOMALY_05000171 (__SILICON_REVISION__ < 5)
-/* DSPID register values incorrect */
-#define ANOMALY_05000172 (__SILICON_REVISION__ < 3)
-/* DMA vs Core accesses to external memory */
-#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
/* Cache Fill Buffer Data lost */
#define ANOMALY_05000174 (__SILICON_REVISION__ < 5)
/* Overlapping Sequencer and Memory Stalls */
@@ -124,8 +73,6 @@
#define ANOMALY_05000189 (__SILICON_REVISION__ < 5)
/* PPI Not Functional at Core Voltage < 1Volt */
#define ANOMALY_05000190 (1)
-/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
-#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
#define ANOMALY_05000193 (__SILICON_REVISION__ < 5)
/* Restarting SPORT in Specific Modes May Cause Data Corruption */
@@ -217,10 +164,10 @@
/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
#define ANOMALY_05000276 (__SILICON_REVISION__ < 5)
/* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */
-#define ANOMALY_05000277 (__SILICON_REVISION__ < 3)
+#define ANOMALY_05000277 (__SILICON_REVISION__ < 5)
/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
#define ANOMALY_05000278 (__SILICON_REVISION__ < 5)
-/* False Hardware Error Exception when ISR Context Is Not Restored */
+/* False Hardware Error when ISR Context Is Not Restored */
/* Temporarily walk around for bug 5423 till this issue is confirmed by
* official anomaly document. It looks 05000281 still exists on bf561
* v0.5.
@@ -274,8 +221,6 @@
#define ANOMALY_05000366 (1)
/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */
#define ANOMALY_05000371 (1)
-/* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */
-#define ANOMALY_05000402 (__SILICON_REVISION__ == 4)
/* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */
#define ANOMALY_05000403 (1)
/* TESTSET Instruction Causes Data Corruption with Writeback Data Cache Enabled */
@@ -298,16 +243,82 @@
#define ANOMALY_05000462 (1)
/* Boot Failure When SDRAM Control Signals Toggle Coming Out Of Reset */
#define ANOMALY_05000471 (1)
-/* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */
+/* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */
#define ANOMALY_05000473 (1)
-/* Possible Lockup Condition whem Modifying PLL from External Memory */
+/* Possible Lockup Condition when Modifying PLL from External Memory */
#define ANOMALY_05000475 (1)
/* TESTSET Instruction Cannot Be Interrupted */
#define ANOMALY_05000477 (1)
/* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */
#define ANOMALY_05000481 (1)
-/* IFLUSH sucks at life */
+/* PLL May Latch Incorrect Values Coming Out of Reset */
+#define ANOMALY_05000489 (1)
+/* Instruction Memory Stalls Can Cause IFLUSH to Fail */
#define ANOMALY_05000491 (1)
+/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */
+#define ANOMALY_05000494 (1)
+/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */
+#define ANOMALY_05000501 (1)
+
+/*
+ * These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
+
+/* Trace Buffers May Contain Errors in Emulation Mode and/or Exception, NMI, Reset Handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* Erroneous Exception when Enabling Cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* Two bits in the Watchpoint Status Register (WPSTAT) are swapped */
+#define ANOMALY_05000134 (__SILICON_REVISION__ < 3)
+/* Enable wires from the Data Watchpoint Address Control Register (WPDACTL) are swapped */
+#define ANOMALY_05000135 (__SILICON_REVISION__ < 3)
+/* Stall in multi-unit DMA operations */
+#define ANOMALY_05000136 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* Infinite Stall may occur with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* Source MDMA descriptor may stop with a DMA Error near beginning of descriptor fetch */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* DMA engine may lose data due to incorrect handshaking */
+#define ANOMALY_05000150 (__SILICON_REVISION__ < 3)
+/* DMA stalls when all three controllers read data from the same source */
+#define ANOMALY_05000151 (__SILICON_REVISION__ < 3)
+/* Execution stall when executing in L2 and doing external accesses */
+#define ANOMALY_05000152 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal stays active in multichannel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Killed 32-Bit MMR Write Leads to Next System MMR Access Thinking It Should Be 32-Bit */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000159 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000160 (__SILICON_REVISION__ < 3)
+/* Data Cache Fill data can be corrupted after/during Instruction DMA if certain core stalls exist */
+#define ANOMALY_05000161 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL<12> is not set on Reset */
+#define ANOMALY_05000162 (__SILICON_REVISION__ < 3)
+/* SPORT Transmit Data Is Not Gated by External Frame Sync in Certain Conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* DSPID register values incorrect */
+#define ANOMALY_05000172 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */
+#define ANOMALY_05000402 (__SILICON_REVISION__ == 4)
/* Anomalies that don't exist on this proc */
#define ANOMALY_05000119 (0)
@@ -337,5 +348,6 @@
#define ANOMALY_05000474 (0)
#define ANOMALY_05000480 (0)
#define ANOMALY_05000485 (0)
+#define ANOMALY_16000030 (0)
#endif
diff --git a/arch/blackfin/mach-bf561/include/mach/defBF561.h b/arch/blackfin/mach-bf561/include/mach/defBF561.h
index 71e805ea74e..9f21f768c63 100644
--- a/arch/blackfin/mach-bf561/include/mach/defBF561.h
+++ b/arch/blackfin/mach-bf561/include/mach/defBF561.h
@@ -1,7 +1,7 @@
/*
* Copyright 2005-2010 Analog Devices Inc.
*
- * Licensed under the ADI BSD license or the GPL-2 (or later)
+ * Licensed under the Clear BSD license or the GPL-2 (or later)
*/
#ifndef _DEF_BF561_H
@@ -479,61 +479,61 @@
#define DMA1_11_PERIPHERAL_MAP 0xFFC01EEC /* DMA1 Channel 11 Peripheral Map Register */
/* Memory DMA1 Controller registers (0xFFC0 1E80-0xFFC0 1FFF) */
-#define MDMA_D2_CONFIG 0xFFC01F08 /*MemDMA1 Stream 0 Destination Configuration */
-#define MDMA_D2_NEXT_DESC_PTR 0xFFC01F00 /*MemDMA1 Stream 0 Destination Next Descriptor Ptr Reg */
-#define MDMA_D2_START_ADDR 0xFFC01F04 /*MemDMA1 Stream 0 Destination Start Address */
-#define MDMA_D2_X_COUNT 0xFFC01F10 /*MemDMA1 Stream 0 Destination Inner-Loop Count */
-#define MDMA_D2_Y_COUNT 0xFFC01F18 /*MemDMA1 Stream 0 Destination Outer-Loop Count */
-#define MDMA_D2_X_MODIFY 0xFFC01F14 /*MemDMA1 Stream 0 Dest Inner-Loop Address-Increment */
-#define MDMA_D2_Y_MODIFY 0xFFC01F1C /*MemDMA1 Stream 0 Dest Outer-Loop Address-Increment */
-#define MDMA_D2_CURR_DESC_PTR 0xFFC01F20 /*MemDMA1 Stream 0 Dest Current Descriptor Ptr reg */
-#define MDMA_D2_CURR_ADDR 0xFFC01F24 /*MemDMA1 Stream 0 Destination Current Address */
-#define MDMA_D2_CURR_X_COUNT 0xFFC01F30 /*MemDMA1 Stream 0 Dest Current Inner-Loop Count */
-#define MDMA_D2_CURR_Y_COUNT 0xFFC01F38 /*MemDMA1 Stream 0 Dest Current Outer-Loop Count */
-#define MDMA_D2_IRQ_STATUS 0xFFC01F28 /*MemDMA1 Stream 0 Destination Interrupt/Status */
-#define MDMA_D2_PERIPHERAL_MAP 0xFFC01F2C /*MemDMA1 Stream 0 Destination Peripheral Map */
-
-#define MDMA_S2_CONFIG 0xFFC01F48 /*MemDMA1 Stream 0 Source Configuration */
-#define MDMA_S2_NEXT_DESC_PTR 0xFFC01F40 /*MemDMA1 Stream 0 Source Next Descriptor Ptr Reg */
-#define MDMA_S2_START_ADDR 0xFFC01F44 /*MemDMA1 Stream 0 Source Start Address */
-#define MDMA_S2_X_COUNT 0xFFC01F50 /*MemDMA1 Stream 0 Source Inner-Loop Count */
-#define MDMA_S2_Y_COUNT 0xFFC01F58 /*MemDMA1 Stream 0 Source Outer-Loop Count */
-#define MDMA_S2_X_MODIFY 0xFFC01F54 /*MemDMA1 Stream 0 Source Inner-Loop Address-Increment */
-#define MDMA_S2_Y_MODIFY 0xFFC01F5C /*MemDMA1 Stream 0 Source Outer-Loop Address-Increment */
-#define MDMA_S2_CURR_DESC_PTR 0xFFC01F60 /*MemDMA1 Stream 0 Source Current Descriptor Ptr reg */
-#define MDMA_S2_CURR_ADDR 0xFFC01F64 /*MemDMA1 Stream 0 Source Current Address */
-#define MDMA_S2_CURR_X_COUNT 0xFFC01F70 /*MemDMA1 Stream 0 Source Current Inner-Loop Count */
-#define MDMA_S2_CURR_Y_COUNT 0xFFC01F78 /*MemDMA1 Stream 0 Source Current Outer-Loop Count */
-#define MDMA_S2_IRQ_STATUS 0xFFC01F68 /*MemDMA1 Stream 0 Source Interrupt/Status */
-#define MDMA_S2_PERIPHERAL_MAP 0xFFC01F6C /*MemDMA1 Stream 0 Source Peripheral Map */
-
-#define MDMA_D3_CONFIG 0xFFC01F88 /*MemDMA1 Stream 1 Destination Configuration */
-#define MDMA_D3_NEXT_DESC_PTR 0xFFC01F80 /*MemDMA1 Stream 1 Destination Next Descriptor Ptr Reg */
-#define MDMA_D3_START_ADDR 0xFFC01F84 /*MemDMA1 Stream 1 Destination Start Address */
-#define MDMA_D3_X_COUNT 0xFFC01F90 /*MemDMA1 Stream 1 Destination Inner-Loop Count */
-#define MDMA_D3_Y_COUNT 0xFFC01F98 /*MemDMA1 Stream 1 Destination Outer-Loop Count */
-#define MDMA_D3_X_MODIFY 0xFFC01F94 /*MemDMA1 Stream 1 Dest Inner-Loop Address-Increment */
-#define MDMA_D3_Y_MODIFY 0xFFC01F9C /*MemDMA1 Stream 1 Dest Outer-Loop Address-Increment */
-#define MDMA_D3_CURR_DESC_PTR 0xFFC01FA0 /*MemDMA1 Stream 1 Dest Current Descriptor Ptr reg */
-#define MDMA_D3_CURR_ADDR 0xFFC01FA4 /*MemDMA1 Stream 1 Dest Current Address */
-#define MDMA_D3_CURR_X_COUNT 0xFFC01FB0 /*MemDMA1 Stream 1 Dest Current Inner-Loop Count */
-#define MDMA_D3_CURR_Y_COUNT 0xFFC01FB8 /*MemDMA1 Stream 1 Dest Current Outer-Loop Count */
-#define MDMA_D3_IRQ_STATUS 0xFFC01FA8 /*MemDMA1 Stream 1 Dest Interrupt/Status */
-#define MDMA_D3_PERIPHERAL_MAP 0xFFC01FAC /*MemDMA1 Stream 1 Dest Peripheral Map */
-
-#define MDMA_S3_CONFIG 0xFFC01FC8 /*MemDMA1 Stream 1 Source Configuration */
-#define MDMA_S3_NEXT_DESC_PTR 0xFFC01FC0 /*MemDMA1 Stream 1 Source Next Descriptor Ptr Reg */
-#define MDMA_S3_START_ADDR 0xFFC01FC4 /*MemDMA1 Stream 1 Source Start Address */
-#define MDMA_S3_X_COUNT 0xFFC01FD0 /*MemDMA1 Stream 1 Source Inner-Loop Count */
-#define MDMA_S3_Y_COUNT 0xFFC01FD8 /*MemDMA1 Stream 1 Source Outer-Loop Count */
-#define MDMA_S3_X_MODIFY 0xFFC01FD4 /*MemDMA1 Stream 1 Source Inner-Loop Address-Increment */
-#define MDMA_S3_Y_MODIFY 0xFFC01FDC /*MemDMA1 Stream 1 Source Outer-Loop Address-Increment */
-#define MDMA_S3_CURR_DESC_PTR 0xFFC01FE0 /*MemDMA1 Stream 1 Source Current Descriptor Ptr reg */
-#define MDMA_S3_CURR_ADDR 0xFFC01FE4 /*MemDMA1 Stream 1 Source Current Address */
-#define MDMA_S3_CURR_X_COUNT 0xFFC01FF0 /*MemDMA1 Stream 1 Source Current Inner-Loop Count */
-#define MDMA_S3_CURR_Y_COUNT 0xFFC01FF8 /*MemDMA1 Stream 1 Source Current Outer-Loop Count */
-#define MDMA_S3_IRQ_STATUS 0xFFC01FE8 /*MemDMA1 Stream 1 Source Interrupt/Status */
-#define MDMA_S3_PERIPHERAL_MAP 0xFFC01FEC /*MemDMA1 Stream 1 Source Peripheral Map */
+#define MDMA_D0_CONFIG 0xFFC01F08 /*MemDMA1 Stream 0 Destination Configuration */
+#define MDMA_D0_NEXT_DESC_PTR 0xFFC01F00 /*MemDMA1 Stream 0 Destination Next Descriptor Ptr Reg */
+#define MDMA_D0_START_ADDR 0xFFC01F04 /*MemDMA1 Stream 0 Destination Start Address */
+#define MDMA_D0_X_COUNT 0xFFC01F10 /*MemDMA1 Stream 0 Destination Inner-Loop Count */
+#define MDMA_D0_Y_COUNT 0xFFC01F18 /*MemDMA1 Stream 0 Destination Outer-Loop Count */
+#define MDMA_D0_X_MODIFY 0xFFC01F14 /*MemDMA1 Stream 0 Dest Inner-Loop Address-Increment */
+#define MDMA_D0_Y_MODIFY 0xFFC01F1C /*MemDMA1 Stream 0 Dest Outer-Loop Address-Increment */
+#define MDMA_D0_CURR_DESC_PTR 0xFFC01F20 /*MemDMA1 Stream 0 Dest Current Descriptor Ptr reg */
+#define MDMA_D0_CURR_ADDR 0xFFC01F24 /*MemDMA1 Stream 0 Destination Current Address */
+#define MDMA_D0_CURR_X_COUNT 0xFFC01F30 /*MemDMA1 Stream 0 Dest Current Inner-Loop Count */
+#define MDMA_D0_CURR_Y_COUNT 0xFFC01F38 /*MemDMA1 Stream 0 Dest Current Outer-Loop Count */
+#define MDMA_D0_IRQ_STATUS 0xFFC01F28 /*MemDMA1 Stream 0 Destination Interrupt/Status */
+#define MDMA_D0_PERIPHERAL_MAP 0xFFC01F2C /*MemDMA1 Stream 0 Destination Peripheral Map */
+
+#define MDMA_S0_CONFIG 0xFFC01F48 /*MemDMA1 Stream 0 Source Configuration */
+#define MDMA_S0_NEXT_DESC_PTR 0xFFC01F40 /*MemDMA1 Stream 0 Source Next Descriptor Ptr Reg */
+#define MDMA_S0_START_ADDR 0xFFC01F44 /*MemDMA1 Stream 0 Source Start Address */
+#define MDMA_S0_X_COUNT 0xFFC01F50 /*MemDMA1 Stream 0 Source Inner-Loop Count */
+#define MDMA_S0_Y_COUNT 0xFFC01F58 /*MemDMA1 Stream 0 Source Outer-Loop Count */
+#define MDMA_S0_X_MODIFY 0xFFC01F54 /*MemDMA1 Stream 0 Source Inner-Loop Address-Increment */
+#define MDMA_S0_Y_MODIFY 0xFFC01F5C /*MemDMA1 Stream 0 Source Outer-Loop Address-Increment */
+#define MDMA_S0_CURR_DESC_PTR 0xFFC01F60 /*MemDMA1 Stream 0 Source Current Descriptor Ptr reg */
+#define MDMA_S0_CURR_ADDR 0xFFC01F64 /*MemDMA1 Stream 0 Source Current Address */
+#define MDMA_S0_CURR_X_COUNT 0xFFC01F70 /*MemDMA1 Stream 0 Source Current Inner-Loop Count */
+#define MDMA_S0_CURR_Y_COUNT 0xFFC01F78 /*MemDMA1 Stream 0 Source Current Outer-Loop Count */
+#define MDMA_S0_IRQ_STATUS 0xFFC01F68 /*MemDMA1 Stream 0 Source Interrupt/Status */
+#define MDMA_S0_PERIPHERAL_MAP 0xFFC01F6C /*MemDMA1 Stream 0 Source Peripheral Map */
+
+#define MDMA_D1_CONFIG 0xFFC01F88 /*MemDMA1 Stream 1 Destination Configuration */
+#define MDMA_D1_NEXT_DESC_PTR 0xFFC01F80 /*MemDMA1 Stream 1 Destination Next Descriptor Ptr Reg */
+#define MDMA_D1_START_ADDR 0xFFC01F84 /*MemDMA1 Stream 1 Destination Start Address */
+#define MDMA_D1_X_COUNT 0xFFC01F90 /*MemDMA1 Stream 1 Destination Inner-Loop Count */
+#define MDMA_D1_Y_COUNT 0xFFC01F98 /*MemDMA1 Stream 1 Destination Outer-Loop Count */
+#define MDMA_D1_X_MODIFY 0xFFC01F94 /*MemDMA1 Stream 1 Dest Inner-Loop Address-Increment */
+#define MDMA_D1_Y_MODIFY 0xFFC01F9C /*MemDMA1 Stream 1 Dest Outer-Loop Address-Increment */
+#define MDMA_D1_CURR_DESC_PTR 0xFFC01FA0 /*MemDMA1 Stream 1 Dest Current Descriptor Ptr reg */
+#define MDMA_D1_CURR_ADDR 0xFFC01FA4 /*MemDMA1 Stream 1 Dest Current Address */
+#define MDMA_D1_CURR_X_COUNT 0xFFC01FB0 /*MemDMA1 Stream 1 Dest Current Inner-Loop Count */
+#define MDMA_D1_CURR_Y_COUNT 0xFFC01FB8 /*MemDMA1 Stream 1 Dest Current Outer-Loop Count */
+#define MDMA_D1_IRQ_STATUS 0xFFC01FA8 /*MemDMA1 Stream 1 Dest Interrupt/Status */
+#define MDMA_D1_PERIPHERAL_MAP 0xFFC01FAC /*MemDMA1 Stream 1 Dest Peripheral Map */
+
+#define MDMA_S1_CONFIG 0xFFC01FC8 /*MemDMA1 Stream 1 Source Configuration */
+#define MDMA_S1_NEXT_DESC_PTR 0xFFC01FC0 /*MemDMA1 Stream 1 Source Next Descriptor Ptr Reg */
+#define MDMA_S1_START_ADDR 0xFFC01FC4 /*MemDMA1 Stream 1 Source Start Address */
+#define MDMA_S1_X_COUNT 0xFFC01FD0 /*MemDMA1 Stream 1 Source Inner-Loop Count */
+#define MDMA_S1_Y_COUNT 0xFFC01FD8 /*MemDMA1 Stream 1 Source Outer-Loop Count */
+#define MDMA_S1_X_MODIFY 0xFFC01FD4 /*MemDMA1 Stream 1 Source Inner-Loop Address-Increment */
+#define MDMA_S1_Y_MODIFY 0xFFC01FDC /*MemDMA1 Stream 1 Source Outer-Loop Address-Increment */
+#define MDMA_S1_CURR_DESC_PTR 0xFFC01FE0 /*MemDMA1 Stream 1 Source Current Descriptor Ptr reg */
+#define MDMA_S1_CURR_ADDR 0xFFC01FE4 /*MemDMA1 Stream 1 Source Current Address */
+#define MDMA_S1_CURR_X_COUNT 0xFFC01FF0 /*MemDMA1 Stream 1 Source Current Inner-Loop Count */
+#define MDMA_S1_CURR_Y_COUNT 0xFFC01FF8 /*MemDMA1 Stream 1 Source Current Outer-Loop Count */
+#define MDMA_S1_IRQ_STATUS 0xFFC01FE8 /*MemDMA1 Stream 1 Source Interrupt/Status */
+#define MDMA_S1_PERIPHERAL_MAP 0xFFC01FEC /*MemDMA1 Stream 1 Source Peripheral Map */
/* DMA2 Controller registers (0xFFC0 0C00-0xFFC0 0DFF) */
#define DMA2_0_CONFIG 0xFFC00C08 /* DMA2 Channel 0 Configuration register */
@@ -705,61 +705,61 @@
#define DMA2_11_PERIPHERAL_MAP 0xFFC00EEC /* DMA2 Channel 11 Peripheral Map Register */
/* Memory DMA2 Controller registers (0xFFC0 0E80-0xFFC0 0FFF) */
-#define MDMA_D0_CONFIG 0xFFC00F08 /*MemDMA2 Stream 0 Destination Configuration register */
-#define MDMA_D0_NEXT_DESC_PTR 0xFFC00F00 /*MemDMA2 Stream 0 Destination Next Descriptor Ptr Reg */
-#define MDMA_D0_START_ADDR 0xFFC00F04 /*MemDMA2 Stream 0 Destination Start Address */
-#define MDMA_D0_X_COUNT 0xFFC00F10 /*MemDMA2 Stream 0 Dest Inner-Loop Count register */
-#define MDMA_D0_Y_COUNT 0xFFC00F18 /*MemDMA2 Stream 0 Dest Outer-Loop Count register */
-#define MDMA_D0_X_MODIFY 0xFFC00F14 /*MemDMA2 Stream 0 Dest Inner-Loop Address-Increment */
-#define MDMA_D0_Y_MODIFY 0xFFC00F1C /*MemDMA2 Stream 0 Dest Outer-Loop Address-Increment */
-#define MDMA_D0_CURR_DESC_PTR 0xFFC00F20 /*MemDMA2 Stream 0 Dest Current Descriptor Ptr reg */
-#define MDMA_D0_CURR_ADDR 0xFFC00F24 /*MemDMA2 Stream 0 Destination Current Address */
-#define MDMA_D0_CURR_X_COUNT 0xFFC00F30 /*MemDMA2 Stream 0 Dest Current Inner-Loop Count reg */
-#define MDMA_D0_CURR_Y_COUNT 0xFFC00F38 /*MemDMA2 Stream 0 Dest Current Outer-Loop Count reg */
-#define MDMA_D0_IRQ_STATUS 0xFFC00F28 /*MemDMA2 Stream 0 Dest Interrupt/Status Register */
-#define MDMA_D0_PERIPHERAL_MAP 0xFFC00F2C /*MemDMA2 Stream 0 Destination Peripheral Map register */
-
-#define MDMA_S0_CONFIG 0xFFC00F48 /*MemDMA2 Stream 0 Source Configuration register */
-#define MDMA_S0_NEXT_DESC_PTR 0xFFC00F40 /*MemDMA2 Stream 0 Source Next Descriptor Ptr Reg */
-#define MDMA_S0_START_ADDR 0xFFC00F44 /*MemDMA2 Stream 0 Source Start Address */
-#define MDMA_S0_X_COUNT 0xFFC00F50 /*MemDMA2 Stream 0 Source Inner-Loop Count register */
-#define MDMA_S0_Y_COUNT 0xFFC00F58 /*MemDMA2 Stream 0 Source Outer-Loop Count register */
-#define MDMA_S0_X_MODIFY 0xFFC00F54 /*MemDMA2 Stream 0 Src Inner-Loop Addr-Increment reg */
-#define MDMA_S0_Y_MODIFY 0xFFC00F5C /*MemDMA2 Stream 0 Src Outer-Loop Addr-Increment reg */
-#define MDMA_S0_CURR_DESC_PTR 0xFFC00F60 /*MemDMA2 Stream 0 Source Current Descriptor Ptr reg */
-#define MDMA_S0_CURR_ADDR 0xFFC00F64 /*MemDMA2 Stream 0 Source Current Address */
-#define MDMA_S0_CURR_X_COUNT 0xFFC00F70 /*MemDMA2 Stream 0 Src Current Inner-Loop Count reg */
-#define MDMA_S0_CURR_Y_COUNT 0xFFC00F78 /*MemDMA2 Stream 0 Src Current Outer-Loop Count reg */
-#define MDMA_S0_IRQ_STATUS 0xFFC00F68 /*MemDMA2 Stream 0 Source Interrupt/Status Register */
-#define MDMA_S0_PERIPHERAL_MAP 0xFFC00F6C /*MemDMA2 Stream 0 Source Peripheral Map register */
-
-#define MDMA_D1_CONFIG 0xFFC00F88 /*MemDMA2 Stream 1 Destination Configuration register */
-#define MDMA_D1_NEXT_DESC_PTR 0xFFC00F80 /*MemDMA2 Stream 1 Destination Next Descriptor Ptr Reg */
-#define MDMA_D1_START_ADDR 0xFFC00F84 /*MemDMA2 Stream 1 Destination Start Address */
-#define MDMA_D1_X_COUNT 0xFFC00F90 /*MemDMA2 Stream 1 Dest Inner-Loop Count register */
-#define MDMA_D1_Y_COUNT 0xFFC00F98 /*MemDMA2 Stream 1 Dest Outer-Loop Count register */
-#define MDMA_D1_X_MODIFY 0xFFC00F94 /*MemDMA2 Stream 1 Dest Inner-Loop Address-Increment */
-#define MDMA_D1_Y_MODIFY 0xFFC00F9C /*MemDMA2 Stream 1 Dest Outer-Loop Address-Increment */
-#define MDMA_D1_CURR_DESC_PTR 0xFFC00FA0 /*MemDMA2 Stream 1 Destination Current Descriptor Ptr */
-#define MDMA_D1_CURR_ADDR 0xFFC00FA4 /*MemDMA2 Stream 1 Destination Current Address reg */
-#define MDMA_D1_CURR_X_COUNT 0xFFC00FB0 /*MemDMA2 Stream 1 Dest Current Inner-Loop Count reg */
-#define MDMA_D1_CURR_Y_COUNT 0xFFC00FB8 /*MemDMA2 Stream 1 Dest Current Outer-Loop Count reg */
-#define MDMA_D1_IRQ_STATUS 0xFFC00FA8 /*MemDMA2 Stream 1 Destination Interrupt/Status Reg */
-#define MDMA_D1_PERIPHERAL_MAP 0xFFC00FAC /*MemDMA2 Stream 1 Destination Peripheral Map register */
-
-#define MDMA_S1_CONFIG 0xFFC00FC8 /*MemDMA2 Stream 1 Source Configuration register */
-#define MDMA_S1_NEXT_DESC_PTR 0xFFC00FC0 /*MemDMA2 Stream 1 Source Next Descriptor Ptr Reg */
-#define MDMA_S1_START_ADDR 0xFFC00FC4 /*MemDMA2 Stream 1 Source Start Address */
-#define MDMA_S1_X_COUNT 0xFFC00FD0 /*MemDMA2 Stream 1 Source Inner-Loop Count register */
-#define MDMA_S1_Y_COUNT 0xFFC00FD8 /*MemDMA2 Stream 1 Source Outer-Loop Count register */
-#define MDMA_S1_X_MODIFY 0xFFC00FD4 /*MemDMA2 Stream 1 Src Inner-Loop Address-Increment */
-#define MDMA_S1_Y_MODIFY 0xFFC00FDC /*MemDMA2 Stream 1 Source Outer-Loop Address-Increment */
-#define MDMA_S1_CURR_DESC_PTR 0xFFC00FE0 /*MemDMA2 Stream 1 Source Current Descriptor Ptr reg */
-#define MDMA_S1_CURR_ADDR 0xFFC00FE4 /*MemDMA2 Stream 1 Source Current Address */
-#define MDMA_S1_CURR_X_COUNT 0xFFC00FF0 /*MemDMA2 Stream 1 Source Current Inner-Loop Count */
-#define MDMA_S1_CURR_Y_COUNT 0xFFC00FF8 /*MemDMA2 Stream 1 Source Current Outer-Loop Count */
-#define MDMA_S1_IRQ_STATUS 0xFFC00FE8 /*MemDMA2 Stream 1 Source Interrupt/Status Register */
-#define MDMA_S1_PERIPHERAL_MAP 0xFFC00FEC /*MemDMA2 Stream 1 Source Peripheral Map register */
+#define MDMA_D2_CONFIG 0xFFC00F08 /*MemDMA2 Stream 0 Destination Configuration register */
+#define MDMA_D2_NEXT_DESC_PTR 0xFFC00F00 /*MemDMA2 Stream 0 Destination Next Descriptor Ptr Reg */
+#define MDMA_D2_START_ADDR 0xFFC00F04 /*MemDMA2 Stream 0 Destination Start Address */
+#define MDMA_D2_X_COUNT 0xFFC00F10 /*MemDMA2 Stream 0 Dest Inner-Loop Count register */
+#define MDMA_D2_Y_COUNT 0xFFC00F18 /*MemDMA2 Stream 0 Dest Outer-Loop Count register */
+#define MDMA_D2_X_MODIFY 0xFFC00F14 /*MemDMA2 Stream 0 Dest Inner-Loop Address-Increment */
+#define MDMA_D2_Y_MODIFY 0xFFC00F1C /*MemDMA2 Stream 0 Dest Outer-Loop Address-Increment */
+#define MDMA_D2_CURR_DESC_PTR 0xFFC00F20 /*MemDMA2 Stream 0 Dest Current Descriptor Ptr reg */
+#define MDMA_D2_CURR_ADDR 0xFFC00F24 /*MemDMA2 Stream 0 Destination Current Address */
+#define MDMA_D2_CURR_X_COUNT 0xFFC00F30 /*MemDMA2 Stream 0 Dest Current Inner-Loop Count reg */
+#define MDMA_D2_CURR_Y_COUNT 0xFFC00F38 /*MemDMA2 Stream 0 Dest Current Outer-Loop Count reg */
+#define MDMA_D2_IRQ_STATUS 0xFFC00F28 /*MemDMA2 Stream 0 Dest Interrupt/Status Register */
+#define MDMA_D2_PERIPHERAL_MAP 0xFFC00F2C /*MemDMA2 Stream 0 Destination Peripheral Map register */
+
+#define MDMA_S2_CONFIG 0xFFC00F48 /*MemDMA2 Stream 0 Source Configuration register */
+#define MDMA_S2_NEXT_DESC_PTR 0xFFC00F40 /*MemDMA2 Stream 0 Source Next Descriptor Ptr Reg */
+#define MDMA_S2_START_ADDR 0xFFC00F44 /*MemDMA2 Stream 0 Source Start Address */
+#define MDMA_S2_X_COUNT 0xFFC00F50 /*MemDMA2 Stream 0 Source Inner-Loop Count register */
+#define MDMA_S2_Y_COUNT 0xFFC00F58 /*MemDMA2 Stream 0 Source Outer-Loop Count register */
+#define MDMA_S2_X_MODIFY 0xFFC00F54 /*MemDMA2 Stream 0 Src Inner-Loop Addr-Increment reg */
+#define MDMA_S2_Y_MODIFY 0xFFC00F5C /*MemDMA2 Stream 0 Src Outer-Loop Addr-Increment reg */
+#define MDMA_S2_CURR_DESC_PTR 0xFFC00F60 /*MemDMA2 Stream 0 Source Current Descriptor Ptr reg */
+#define MDMA_S2_CURR_ADDR 0xFFC00F64 /*MemDMA2 Stream 0 Source Current Address */
+#define MDMA_S2_CURR_X_COUNT 0xFFC00F70 /*MemDMA2 Stream 0 Src Current Inner-Loop Count reg */
+#define MDMA_S2_CURR_Y_COUNT 0xFFC00F78 /*MemDMA2 Stream 0 Src Current Outer-Loop Count reg */
+#define MDMA_S2_IRQ_STATUS 0xFFC00F68 /*MemDMA2 Stream 0 Source Interrupt/Status Register */
+#define MDMA_S2_PERIPHERAL_MAP 0xFFC00F6C /*MemDMA2 Stream 0 Source Peripheral Map register */
+
+#define MDMA_D3_CONFIG 0xFFC00F88 /*MemDMA2 Stream 1 Destination Configuration register */
+#define MDMA_D3_NEXT_DESC_PTR 0xFFC00F80 /*MemDMA2 Stream 1 Destination Next Descriptor Ptr Reg */
+#define MDMA_D3_START_ADDR 0xFFC00F84 /*MemDMA2 Stream 1 Destination Start Address */
+#define MDMA_D3_X_COUNT 0xFFC00F90 /*MemDMA2 Stream 1 Dest Inner-Loop Count register */
+#define MDMA_D3_Y_COUNT 0xFFC00F98 /*MemDMA2 Stream 1 Dest Outer-Loop Count register */
+#define MDMA_D3_X_MODIFY 0xFFC00F94 /*MemDMA2 Stream 1 Dest Inner-Loop Address-Increment */
+#define MDMA_D3_Y_MODIFY 0xFFC00F9C /*MemDMA2 Stream 1 Dest Outer-Loop Address-Increment */
+#define MDMA_D3_CURR_DESC_PTR 0xFFC00FA0 /*MemDMA2 Stream 1 Destination Current Descriptor Ptr */
+#define MDMA_D3_CURR_ADDR 0xFFC00FA4 /*MemDMA2 Stream 1 Destination Current Address reg */
+#define MDMA_D3_CURR_X_COUNT 0xFFC00FB0 /*MemDMA2 Stream 1 Dest Current Inner-Loop Count reg */
+#define MDMA_D3_CURR_Y_COUNT 0xFFC00FB8 /*MemDMA2 Stream 1 Dest Current Outer-Loop Count reg */
+#define MDMA_D3_IRQ_STATUS 0xFFC00FA8 /*MemDMA2 Stream 1 Destination Interrupt/Status Reg */
+#define MDMA_D3_PERIPHERAL_MAP 0xFFC00FAC /*MemDMA2 Stream 1 Destination Peripheral Map register */
+
+#define MDMA_S3_CONFIG 0xFFC00FC8 /*MemDMA2 Stream 1 Source Configuration register */
+#define MDMA_S3_NEXT_DESC_PTR 0xFFC00FC0 /*MemDMA2 Stream 1 Source Next Descriptor Ptr Reg */
+#define MDMA_S3_START_ADDR 0xFFC00FC4 /*MemDMA2 Stream 1 Source Start Address */
+#define MDMA_S3_X_COUNT 0xFFC00FD0 /*MemDMA2 Stream 1 Source Inner-Loop Count register */
+#define MDMA_S3_Y_COUNT 0xFFC00FD8 /*MemDMA2 Stream 1 Source Outer-Loop Count register */
+#define MDMA_S3_X_MODIFY 0xFFC00FD4 /*MemDMA2 Stream 1 Src Inner-Loop Address-Increment */
+#define MDMA_S3_Y_MODIFY 0xFFC00FDC /*MemDMA2 Stream 1 Source Outer-Loop Address-Increment */
+#define MDMA_S3_CURR_DESC_PTR 0xFFC00FE0 /*MemDMA2 Stream 1 Source Current Descriptor Ptr reg */
+#define MDMA_S3_CURR_ADDR 0xFFC00FE4 /*MemDMA2 Stream 1 Source Current Address */
+#define MDMA_S3_CURR_X_COUNT 0xFFC00FF0 /*MemDMA2 Stream 1 Source Current Inner-Loop Count */
+#define MDMA_S3_CURR_Y_COUNT 0xFFC00FF8 /*MemDMA2 Stream 1 Source Current Outer-Loop Count */
+#define MDMA_S3_IRQ_STATUS 0xFFC00FE8 /*MemDMA2 Stream 1 Source Interrupt/Status Register */
+#define MDMA_S3_PERIPHERAL_MAP 0xFFC00FEC /*MemDMA2 Stream 1 Source Peripheral Map register */
/* Internal Memory DMA Registers (0xFFC0_1800 - 0xFFC0_19FF) */
#define IMDMA_D0_CONFIG 0xFFC01808 /*IMDMA Stream 0 Destination Configuration */
@@ -879,6 +879,13 @@
#define DLENGTH 0x00003800 /* PPI Data Length */
#define DLEN_8 0x0 /* PPI Data Length mask for DLEN=8 */
#define DLEN(x) (((x-9) & 0x07) << 11) /* PPI Data Length (only works for x=10-->x=16) */
+#define DLEN_10 0x00000800 /* Data Length = 10 Bits */
+#define DLEN_11 0x00001000 /* Data Length = 11 Bits */
+#define DLEN_12 0x00001800 /* Data Length = 12 Bits */
+#define DLEN_13 0x00002000 /* Data Length = 13 Bits */
+#define DLEN_14 0x00002800 /* Data Length = 14 Bits */
+#define DLEN_15 0x00003000 /* Data Length = 15 Bits */
+#define DLEN_16 0x00003800 /* Data Length = 16 Bits */
#define POL 0x0000C000 /* PPI Signal Polarities */
#define POLC 0x4000 /* PPI Clock Polarity */
#define POLS 0x8000 /* PPI Frame Sync Polarity */
diff --git a/arch/blackfin/mach-bf561/include/mach/gpio.h b/arch/blackfin/mach-bf561/include/mach/gpio.h
index 57d5eab59fa..f9f8b2adf4b 100644
--- a/arch/blackfin/mach-bf561/include/mach/gpio.h
+++ b/arch/blackfin/mach-bf561/include/mach/gpio.h
@@ -58,9 +58,9 @@
#define GPIO_PF46 46
#define GPIO_PF47 47
-#define PORT_FIO0 GPIO_0
-#define PORT_FIO1 GPIO_16
-#define PORT_FIO2 GPIO_32
+#define PORT_FIO0 GPIO_PF0
+#define PORT_FIO1 GPIO_PF16
+#define PORT_FIO2 GPIO_PF32
#include <mach-common/ports-f.h>
diff --git a/arch/blackfin/mach-bf561/include/mach/pll.h b/arch/blackfin/mach-bf561/include/mach/pll.h
index 7977db2f1c1..00bdacee9cc 100644
--- a/arch/blackfin/mach-bf561/include/mach/pll.h
+++ b/arch/blackfin/mach-bf561/include/mach/pll.h
@@ -16,6 +16,7 @@
#include <mach/irq.h>
#define SUPPLE_0_WAKEUP ((IRQ_SUPPLE_0 - (IRQ_CORETMR + 1)) % 32)
+#define SUPPLE_1_WAKEUP ((IRQ_SUPPLE_1 - (IRQ_CORETMR + 1)) % 32)
static inline void
bfin_iwr_restore(unsigned long iwr0, unsigned long iwr1, unsigned long iwr2)
@@ -42,7 +43,8 @@ bfin_iwr_save(unsigned long niwr0, unsigned long niwr1, unsigned long niwr2,
static inline void
bfin_iwr_set_sup0(unsigned long *iwr0, unsigned long *iwr1, unsigned long *iwr2)
{
- bfin_iwr_save(0, IWR_ENABLE(SUPPLE_0_WAKEUP), 0, iwr0, iwr1, iwr2);
+ bfin_iwr_save(0, IWR_ENABLE(SUPPLE_0_WAKEUP) |
+ IWR_ENABLE(SUPPLE_1_WAKEUP), 0, iwr0, iwr1, iwr2);
}
#endif
diff --git a/arch/blackfin/mach-bf561/secondary.S b/arch/blackfin/mach-bf561/secondary.S
index 4c462838f4e..01e5408620a 100644
--- a/arch/blackfin/mach-bf561/secondary.S
+++ b/arch/blackfin/mach-bf561/secondary.S
@@ -23,108 +23,78 @@
#define INITIAL_STACK (COREB_L1_SCRATCH_START + L1_SCRATCH_LENGTH - 12)
ENTRY(_coreb_trampoline_start)
- /* Set the SYSCFG register */
- R0 = 0x36;
- SYSCFG = R0; /*Enable Cycle Counter and Nesting Of Interrupts(3rd Bit)*/
- R0 = 0;
-
- /*Clear Out All the data and pointer Registers*/
- R1 = R0;
- R2 = R0;
- R3 = R0;
- R4 = R0;
- R5 = R0;
- R6 = R0;
- R7 = R0;
-
- P0 = R0;
- P1 = R0;
- P2 = R0;
- P3 = R0;
- P4 = R0;
- P5 = R0;
-
- LC0 = r0;
- LC1 = r0;
- L0 = r0;
- L1 = r0;
- L2 = r0;
- L3 = r0;
-
- /* Clear Out All the DAG Registers*/
- B0 = r0;
- B1 = r0;
- B2 = r0;
- B3 = r0;
-
- I0 = r0;
- I1 = r0;
- I2 = r0;
- I3 = r0;
-
- M0 = r0;
- M1 = r0;
- M2 = r0;
- M3 = r0;
+ /* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+ R0 = SYSCFG_SNEN;
+#else
+ R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
+ SYSCFG = R0;
- trace_buffer_init(p0,r0);
+ /* Optimization register tricks: keep a base value in the
+ * reserved P registers so we use the load/store with an
+ * offset syntax. R0 = [P5 + <constant>];
+ * P5 - core MMR base
+ * R6 - 0
+ */
+ r6 = 0;
+ p5.l = 0;
+ p5.h = hi(COREMMR_BASE);
- /* Turn off the icache */
- p0.l = LO(IMEM_CONTROL);
- p0.h = HI(IMEM_CONTROL);
- R1 = [p0];
- R0 = ~ENICPLB;
- R0 = R0 & R1;
+ /* Zero out registers required by Blackfin ABI */
- /* Disabling of CPLBs should be proceeded by a CSYNC */
+ /* Disable circular buffers */
+ L0 = r6;
+ L1 = r6;
+ L2 = r6;
+ L3 = r6;
+
+ /* Disable hardware loops in case we were started by 'go' */
+ LC0 = r6;
+ LC1 = r6;
+
+ /*
+ * Clear ITEST_COMMAND and DTEST_COMMAND registers,
+ * Leaving these as non-zero can confuse the emulator
+ */
+ [p5 + (DTEST_COMMAND - COREMMR_BASE)] = r6;
+ [p5 + (ITEST_COMMAND - COREMMR_BASE)] = r6;
CSYNC;
- [p0] = R0;
+
+ trace_buffer_init(p0,r0);
+
+ /* Turn off the icache */
+ r1 = [p5 + (IMEM_CONTROL - COREMMR_BASE)];
+ BITCLR (r1, ENICPLB_P);
+ [p5 + (IMEM_CONTROL - COREMMR_BASE)] = r1;
SSYNC;
/* Turn off the dcache */
- p0.l = LO(DMEM_CONTROL);
- p0.h = HI(DMEM_CONTROL);
- R1 = [p0];
- R0 = ~ENDCPLB;
- R0 = R0 & R1;
-
- /* Disabling of CPLBs should be proceeded by a CSYNC */
- CSYNC;
- [p0] = R0;
+ r1 = [p5 + (DMEM_CONTROL - COREMMR_BASE)];
+ BITCLR (r1, ENDCPLB_P);
+ [p5 + (DMEM_CONTROL - COREMMR_BASE)] = r1;
SSYNC;
/* in case of double faults, save a few things */
- p0.l = _init_retx_coreb;
- p0.h = _init_retx_coreb;
- R0 = RETX;
- [P0] = R0;
-
+ p1.l = _initial_pda_coreb;
+ p1.h = _initial_pda_coreb;
+ r4 = RETX;
#ifdef CONFIG_DEBUG_DOUBLEFAULT
/* Only save these if we are storing them,
* This happens here, since L1 gets clobbered
* below
*/
GET_PDA(p0, r0);
- r7 = [p0 + PDA_DF_RETX];
- p1.l = _init_saved_retx_coreb;
- p1.h = _init_saved_retx_coreb;
- [p1] = r7;
-
- r7 = [p0 + PDA_DF_DCPLB];
- p1.l = _init_saved_dcplb_fault_addr_coreb;
- p1.h = _init_saved_dcplb_fault_addr_coreb;
- [p1] = r7;
-
- r7 = [p0 + PDA_DF_ICPLB];
- p1.l = _init_saved_icplb_fault_addr_coreb;
- p1.h = _init_saved_icplb_fault_addr_coreb;
- [p1] = r7;
-
- r7 = [p0 + PDA_DF_SEQSTAT];
- p1.l = _init_saved_seqstat_coreb;
- p1.h = _init_saved_seqstat_coreb;
- [p1] = r7;
+ r0 = [p0 + PDA_DF_RETX];
+ r1 = [p0 + PDA_DF_DCPLB];
+ r2 = [p0 + PDA_DF_ICPLB];
+ r3 = [p0 + PDA_DF_SEQSTAT];
+ [p1 + PDA_INIT_DF_RETX] = r0;
+ [p1 + PDA_INIT_DF_DCPLB] = r1;
+ [p1 + PDA_INIT_DF_ICPLB] = r2;
+ [p1 + PDA_INIT_DF_SEQSTAT] = r3;
#endif
+ [p1 + PDA_INIT_RETX] = r4;
/* Initialize stack pointer */
sp.l = lo(INITIAL_STACK);
@@ -138,19 +108,13 @@ ENTRY(_coreb_trampoline_start)
/* EVT15 = _real_start */
- p0.l = lo(EVT15);
- p0.h = hi(EVT15);
p1.l = _coreb_start;
p1.h = _coreb_start;
- [p0] = p1;
+ [p5 + (EVT15 - COREMMR_BASE)] = p1;
csync;
- p0.l = lo(IMASK);
- p0.h = hi(IMASK);
- p1.l = IMASK_IVG15;
- p1.h = 0x0;
- [p0] = p1;
- csync;
+ r0 = EVT_IVG15 (z);
+ sti r0;
raise 15;
p0.l = .LWAIT_HERE;
diff --git a/arch/blackfin/mach-bf561/smp.c b/arch/blackfin/mach-bf561/smp.c
index 85abd8be134..11789beca75 100644
--- a/arch/blackfin/mach-bf561/smp.c
+++ b/arch/blackfin/mach-bf561/smp.c
@@ -48,7 +48,7 @@ int __init setup_profiling_timer(unsigned int multiplier) /* not supported */
return -EINVAL;
}
-void __cpuinit platform_secondary_init(unsigned int cpu)
+void platform_secondary_init(unsigned int cpu)
{
/* Clone setup for peripheral interrupt sources from CoreA. */
bfin_write_SICB_IMASK0(bfin_read_SIC_IMASK0());
@@ -69,12 +69,11 @@ void __cpuinit platform_secondary_init(unsigned int cpu)
SSYNC();
/* We are done with local CPU inits, unblock the boot CPU. */
- set_cpu_online(cpu, true);
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
}
-int __cpuinit platform_boot_secondary(unsigned int cpu, struct task_struct *idle)
+int platform_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned long timeout;
@@ -84,14 +83,16 @@ int __cpuinit platform_boot_secondary(unsigned int cpu, struct task_struct *idle
if ((bfin_read_SYSCR() & COREB_SRAM_INIT) == 0) {
/* CoreB already running, sending ipi to wakeup it */
- platform_send_ipi_cpu(cpu, IRQ_SUPPLE_0);
+ smp_send_reschedule(cpu);
} else {
/* Kick CoreB, which should start execution from CORE_SRAM_BASE. */
bfin_write_SYSCR(bfin_read_SYSCR() & ~COREB_SRAM_INIT);
SSYNC();
}
- timeout = jiffies + 1 * HZ;
+ timeout = jiffies + HZ;
+ /* release the lock and let coreb run */
+ spin_unlock(&boot_lock);
while (time_before(jiffies, timeout)) {
if (cpu_online(cpu))
break;
@@ -100,8 +101,6 @@ int __cpuinit platform_boot_secondary(unsigned int cpu, struct task_struct *idle
}
if (cpu_online(cpu)) {
- /* release the lock and let coreb run */
- spin_unlock(&boot_lock);
return 0;
} else
panic("CPU%u: processor failed to boot\n", cpu);
@@ -114,7 +113,8 @@ void __init platform_request_ipi(int irq, void *handler)
int ret;
const char *name = (irq == IRQ_SUPPLE_0) ? supple0 : supple1;
- ret = request_irq(irq, handler, IRQF_DISABLED | IRQF_PERCPU, name, handler);
+ ret = request_irq(irq, handler, IRQF_PERCPU | IRQF_NO_SUSPEND |
+ IRQF_FORCE_RESUME, name, handler);
if (ret)
panic("Cannot request %s for IPI service", name);
}
@@ -154,7 +154,7 @@ void platform_clear_ipi(unsigned int cpu, int irq)
* Setup core B's local core timer.
* In SMP, core timer is used for clock event device.
*/
-void __cpuinit bfin_local_timer_setup(void)
+void bfin_local_timer_setup(void)
{
#if defined(CONFIG_TICKSOURCE_CORETMR)
struct irq_data *data = irq_get_irq_data(IRQ_CORETMR);
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-12-15 02:20:06 +0000