diff options
Diffstat (limited to 'arch/blackfin/mach-bf561/boards/cm_bf561.c')
| -rw-r--r-- | arch/blackfin/mach-bf561/boards/cm_bf561.c | 190 |
1 files changed, 114 insertions, 76 deletions
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c index dfc8d5b7798..e862f7823e6 100644 --- a/arch/blackfin/mach-bf561/boards/cm_bf561.c +++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c @@ -13,11 +13,12 @@ #include <linux/mtd/partitions.h> #include <linux/spi/spi.h> #include <linux/spi/flash.h> -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_ISP1362_HCD) #include <linux/usb/isp1362.h> #endif #include <linux/ata_platform.h> #include <linux/irq.h> +#include <linux/gpio.h> #include <asm/dma.h> #include <asm/bfin5xx_spi.h> #include <asm/portmux.h> @@ -29,10 +30,10 @@ */ const char bfin_board_name[] = "Bluetechnix CM BF561"; -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) /* all SPI peripherals info goes here */ -#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) static struct mtd_partition bfin_spi_flash_partitions[] = { { .name = "bootloader(spi)", @@ -60,34 +61,11 @@ static struct flash_platform_data bfin_spi_flash_data = { /* SPI flash chip (m25p64) */ static struct bfin5xx_spi_chip spi_flash_chip_info = { .enable_dma = 0, /* use dma transfer with this chip*/ - .bits_per_word = 8, -}; -#endif - -#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) -/* SPI ADC chip */ -static struct bfin5xx_spi_chip spi_adc_chip_info = { - .enable_dma = 1, /* use dma transfer with this chip*/ - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) -static struct bfin5xx_spi_chip ad1836_spi_chip_info = { - .enable_dma = 0, - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) -static struct bfin5xx_spi_chip mmc_spi_chip_info = { - .enable_dma = 0, - .bits_per_word = 8, }; #endif static struct spi_board_info bfin_spi_board_info[] __initdata = { -#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) { /* the modalias must be the same as spi device driver name */ .modalias = "m25p80", /* Name of spi_driver for this device */ @@ -100,33 +78,20 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { }, #endif -#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) - { - .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ - .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, /* Framework bus number */ - .chip_select = 1, /* Framework chip select. */ - .platform_data = NULL, /* No spi_driver specific config */ - .controller_data = &spi_adc_chip_info, - }, -#endif - -#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X) { - .modalias = "ad1836", + .modalias = "ad183x", .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, - .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, - .controller_data = &ad1836_spi_chip_info, + .chip_select = 4, }, #endif -#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) +#if IS_ENABLED(CONFIG_MMC_SPI) { .modalias = "mmc_spi", .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, .chip_select = 1, - .controller_data = &mmc_spi_chip_info, .mode = SPI_MODE_3, }, #endif @@ -170,14 +135,14 @@ static struct platform_device bfin_spi0_device = { #endif /* spi master and devices */ -#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) +#if IS_ENABLED(CONFIG_FB_HITACHI_TX09) static struct platform_device hitachi_fb_device = { .name = "hitachi-tx09", }; #endif -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +#if IS_ENABLED(CONFIG_SMC91X) #include <linux/smc91x.h> static struct smc91x_platdata smc91x_info = { @@ -209,7 +174,7 @@ static struct platform_device smc91x_device = { }; #endif -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#if IS_ENABLED(CONFIG_SMSC911X) #include <linux/smsc911x.h> static struct resource smsc911x_resources[] = { @@ -244,7 +209,7 @@ static struct platform_device smsc911x_device = { }; #endif -#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +#if IS_ENABLED(CONFIG_USB_NET2272) static struct resource net2272_bfin_resources[] = { { .start = 0x24000000, @@ -265,7 +230,7 @@ static struct platform_device net2272_bfin_device = { }; #endif -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_ISP1362_HCD) static struct resource isp1362_hcd_resources[] = { { .start = 0x24008000, @@ -278,7 +243,7 @@ static struct resource isp1362_hcd_resources[] = { }, { .start = IRQ_PF47, .end = IRQ_PF47, - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, }, }; @@ -304,24 +269,58 @@ static struct platform_device isp1362_hcd_device = { }; #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) -static struct resource bfin_uart_resources[] = { +#if IS_ENABLED(CONFIG_SERIAL_BFIN) +#ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { { - .start = 0xFFC00400, - .end = 0xFFC004FF, + .start = BFIN_UART_THR, + .end = BFIN_UART_GCTL+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART_TX, + .end = IRQ_UART_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART_RX, + .end = IRQ_UART_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART_ERROR, + .end = IRQ_UART_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART_TX, + .end = CH_UART_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART_RX, + .end = CH_UART_RX, + .flags = IORESOURCE_DMA, + }, }; -static struct platform_device bfin_uart_device = { +static unsigned short bfin_uart0_peripherals[] = { + P_UART0_TX, P_UART0_RX, 0 +}; + +static struct platform_device bfin_uart0_device = { .name = "bfin-uart", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_uart_resources), - .resource = bfin_uart_resources, + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, + .dev = { + .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ + }, }; #endif +#endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 static struct resource bfin_sir0_resources[] = { { @@ -350,12 +349,12 @@ static struct platform_device bfin_sir0_device = { #endif #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) +#if IS_ENABLED(CONFIG_PATA_PLATFORM) #define PATA_INT IRQ_PF46 static struct pata_platform_info bfin_pata_platform_data = { .ioport_shift = 2, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, + .irq_type = IRQF_TRIGGER_HIGH, }; static struct resource bfin_pata_resources[] = { @@ -387,7 +386,7 @@ static struct platform_device bfin_pata_device = { }; #endif -#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +#if IS_ENABLED(CONFIG_MTD_PHYSMAP) static struct mtd_partition para_partitions[] = { { .name = "bootloader(nor)", @@ -458,61 +457,100 @@ static struct platform_device *cm_bf561_devices[] __initdata = { &bfin_dpmc, -#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) +#if IS_ENABLED(CONFIG_FB_HITACHI_TX09) &hitachi_fb_device, #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) - &bfin_uart_device, +#if IS_ENABLED(CONFIG_SERIAL_BFIN) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif #endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 &bfin_sir0_device, #endif #endif -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_ISP1362_HCD) &isp1362_hcd_device, #endif -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +#if IS_ENABLED(CONFIG_SMC91X) &smc91x_device, #endif -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#if IS_ENABLED(CONFIG_SMSC911X) &smsc911x_device, #endif -#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +#if IS_ENABLED(CONFIG_USB_NET2272) &net2272_bfin_device, #endif -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) &bfin_spi0_device, #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) +#if IS_ENABLED(CONFIG_PATA_PLATFORM) &bfin_pata_device, #endif -#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +#if IS_ENABLED(CONFIG_MTD_PHYSMAP) ¶_flash_device, #endif }; +static int __init net2272_init(void) +{ +#if IS_ENABLED(CONFIG_USB_NET2272) + int ret; + + ret = gpio_request(GPIO_PF46, "net2272"); + if (ret) + return ret; + + /* Reset USB Chip, PF46 */ + gpio_direction_output(GPIO_PF46, 0); + mdelay(2); + gpio_set_value(GPIO_PF46, 1); +#endif + + return 0; +} + static int __init cm_bf561_init(void) { printk(KERN_INFO "%s(): registering device resources\n", __func__); platform_add_devices(cm_bf561_devices, ARRAY_SIZE(cm_bf561_devices)); -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; +#if IS_ENABLED(CONFIG_PATA_PLATFORM) + irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN); #endif + + if (net2272_init()) + pr_warning("unable to configure net2272; it probably won't work\n"); + return 0; } arch_initcall(cm_bf561_init); + +static struct platform_device *cm_bf561_early_devices[] __initdata = { +#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#endif +}; + +void __init native_machine_early_platform_add_devices(void) +{ + printk(KERN_INFO "register early platform devices\n"); + early_platform_add_devices(cm_bf561_early_devices, + ARRAY_SIZE(cm_bf561_early_devices)); +} |