diff options
Diffstat (limited to 'arch/blackfin/mach-bf548')
25 files changed, 2139 insertions, 2494 deletions
diff --git a/arch/blackfin/mach-bf548/Kconfig b/arch/blackfin/mach-bf548/Kconfig index 70189a0d1a1..334ec7b1218 100644 --- a/arch/blackfin/mach-bf548/Kconfig +++ b/arch/blackfin/mach-bf548/Kconfig @@ -42,6 +42,65 @@ config BF548_ATAPI_ALTERNATIVE_PORT async address or GPIO port F and G. Select y to route it to GPIO. +choice + prompt "UART2 DMA channel selection" + depends on SERIAL_BFIN_UART2 + default UART2_DMA_RX_ON_DMA18 + help + UART2 DMA channel selection + RX -> DMA18 + TX -> DMA19 + or + RX -> DMA13 + TX -> DMA14 + +config UART2_DMA_RX_ON_DMA18 + bool "UART2 DMA RX -> DMA18 TX -> DMA19" + help + UART2 DMA channel assignment + RX -> DMA18 + TX -> DMA19 + use SPORT2 default DMA channel + +config UART2_DMA_RX_ON_DMA13 + bool "UART2 DMA RX -> DMA13 TX -> DMA14" + help + UART2 DMA channel assignment + RX -> DMA13 + TX -> DMA14 + use EPPI1 EPPI2 default DMA channel +endchoice + +choice + prompt "UART3 DMA channel selection" + depends on SERIAL_BFIN_UART3 + default UART3_DMA_RX_ON_DMA20 + help + UART3 DMA channel selection + RX -> DMA20 + TX -> DMA21 + or + RX -> DMA15 + TX -> DMA16 + +config UART3_DMA_RX_ON_DMA20 + bool "UART3 DMA RX -> DMA20 TX -> DMA21" + help + UART3 DMA channel assignment + RX -> DMA20 + TX -> DMA21 + use SPORT3 default DMA channel + +config UART3_DMA_RX_ON_DMA15 + bool "UART3 DMA RX -> DMA15 TX -> DMA16" + help + UART3 DMA channel assignment + RX -> DMA15 + TX -> DMA16 + use PIXC default DMA channel + +endchoice + comment "Interrupt Priority Assignment" menu "Priority" @@ -318,40 +377,6 @@ config IRQ_PINT3 endmenu -comment "Pin Interrupt to Port Assignment" -menu "Assignment" - -config PINTx_REASSIGN - bool "Reprogram PINT Assignment" - default y - help - The interrupt assignment registers controls the pin-to-interrupt - assignment in a byte-wide manner. Each option allows you to select - a set of pins (High/Low Byte) of an specific Port being mapped - to one of the four PIN Interrupts IRQ_PINTx. - - You shouldn't change any of these unless you know exactly what you're doing. - Please consult the Blackfin BF54x Processor Hardware Reference Manual. - -config PINT0_ASSIGN - hex "PINT0_ASSIGN" - depends on PINTx_REASSIGN - default 0x00000101 -config PINT1_ASSIGN - hex "PINT1_ASSIGN" - depends on PINTx_REASSIGN - default 0x01010000 -config PINT2_ASSIGN - hex "PINT2_ASSIGN" - depends on PINTx_REASSIGN - default 0x07000101 -config PINT3_ASSIGN - hex "PINT3_ASSIGN" - depends on PINTx_REASSIGN - default 0x02020303 - -endmenu - endmenu endif diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c index ccdcd6da2e9..6d5ffdead06 100644 --- a/arch/blackfin/mach-bf548/boards/cm_bf548.c +++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c @@ -37,7 +37,7 @@ const char bfin_board_name[] = "Bluetechnix CM-BF548"; * Driver needs to know address, irq and flag pin. */ -#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE) +#if IS_ENABLED(CONFIG_FB_BF54X_LQ043) #include <mach/bf54x-lq043.h> @@ -69,7 +69,7 @@ static struct platform_device bf54x_lq043_device = { }; #endif -#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_BFIN) static unsigned int bf548_keymap[] = { KEYVAL(0, 0, KEY_ENTER), KEYVAL(0, 1, KEY_HELP), @@ -119,54 +119,241 @@ static struct platform_device bf54x_kpad_device = { }; #endif -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +#if IS_ENABLED(CONFIG_RTC_DRV_BFIN) static struct platform_device rtc_device = { .name = "rtc-bfin", .id = -1, }; #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) -static struct resource bfin_uart_resources[] = { +#if IS_ENABLED(CONFIG_SERIAL_BFIN) #ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { { - .start = 0xFFC00400, - .end = 0xFFC004FF, + .start = UART0_DLL, + .end = UART0_RBR+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_TX, + .end = IRQ_UART0_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_ERROR, + .end = IRQ_UART0_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_TX, + .end = CH_UART0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static unsigned short bfin_uart0_peripherals[] = { + P_UART0_TX, P_UART0_RX, 0 +}; + +static struct platform_device bfin_uart0_device = { + .name = "bfin-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, + .dev = { + .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ + }, +}; #endif #ifdef CONFIG_SERIAL_BFIN_UART1 +static struct resource bfin_uart1_resources[] = { { - .start = 0xFFC02000, - .end = 0xFFC020FF, + .start = UART1_DLL, + .end = UART1_RBR+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART1_TX, + .end = IRQ_UART1_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART1_ERROR, + .end = IRQ_UART1_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_TX, + .end = CH_UART1_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART1_CTSRTS + { /* CTS pin -- 0 means not supported */ + .start = GPIO_PE10, + .end = GPIO_PE10, + .flags = IORESOURCE_IO, + }, + { /* RTS pin -- 0 means not supported */ + .start = GPIO_PE9, + .end = GPIO_PE9, + .flags = IORESOURCE_IO, + }, +#endif +}; + +static unsigned short bfin_uart1_peripherals[] = { + P_UART1_TX, P_UART1_RX, +#ifdef CONFIG_BFIN_UART1_CTSRTS + P_UART1_RTS, P_UART1_CTS, +#endif + 0 +}; + +static struct platform_device bfin_uart1_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart1_resources), + .resource = bfin_uart1_resources, + .dev = { + .platform_data = &bfin_uart1_peripherals, /* Passed to driver */ + }, +}; #endif #ifdef CONFIG_SERIAL_BFIN_UART2 +static struct resource bfin_uart2_resources[] = { { - .start = 0xFFC02100, - .end = 0xFFC021FF, + .start = UART2_DLL, + .end = UART2_RBR+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART2_TX, + .end = IRQ_UART2_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART2_RX, + .end = IRQ_UART2_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART2_ERROR, + .end = IRQ_UART2_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART2_TX, + .end = CH_UART2_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART2_RX, + .end = CH_UART2_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static unsigned short bfin_uart2_peripherals[] = { + P_UART2_TX, P_UART2_RX, 0 +}; + +static struct platform_device bfin_uart2_device = { + .name = "bfin-uart", + .id = 2, + .num_resources = ARRAY_SIZE(bfin_uart2_resources), + .resource = bfin_uart2_resources, + .dev = { + .platform_data = &bfin_uart2_peripherals, /* Passed to driver */ + }, +}; #endif #ifdef CONFIG_SERIAL_BFIN_UART3 +static struct resource bfin_uart3_resources[] = { { - .start = 0xFFC03100, - .end = 0xFFC031FF, + .start = UART3_DLL, + .end = UART3_RBR+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART3_TX, + .end = IRQ_UART3_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART3_RX, + .end = IRQ_UART3_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART3_ERROR, + .end = IRQ_UART3_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART3_TX, + .end = CH_UART3_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART3_RX, + .end = CH_UART3_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART3_CTSRTS + { /* CTS pin -- 0 means not supported */ + .start = GPIO_PB3, + .end = GPIO_PB3, + .flags = IORESOURCE_IO, + }, + { /* RTS pin -- 0 means not supported */ + .start = GPIO_PB2, + .end = GPIO_PB2, + .flags = IORESOURCE_IO, + }, +#endif +}; + +static unsigned short bfin_uart3_peripherals[] = { + P_UART3_TX, P_UART3_RX, +#ifdef CONFIG_BFIN_UART3_CTSRTS + P_UART3_RTS, P_UART3_CTS, #endif + 0 }; -static struct platform_device bfin_uart_device = { +static struct platform_device bfin_uart3_device = { .name = "bfin-uart", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_uart_resources), - .resource = bfin_uart_resources, + .id = 3, + .num_resources = ARRAY_SIZE(bfin_uart3_resources), + .resource = bfin_uart3_resources, + .dev = { + .platform_data = &bfin_uart3_peripherals, /* Passed to driver */ + }, }; #endif +#endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 static struct resource bfin_sir0_resources[] = { { @@ -269,7 +456,7 @@ static struct platform_device bfin_sir3_device = { #endif #endif -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#if IS_ENABLED(CONFIG_SMSC911X) #include <linux/smsc911x.h> static struct resource smsc911x_resources[] = { @@ -304,7 +491,7 @@ static struct platform_device smsc911x_device = { }; #endif -#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) +#if IS_ENABLED(CONFIG_USB_MUSB_HDRC) static struct resource musb_resources[] = { [0] = { .start = 0xFFC03C00, @@ -315,11 +502,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -331,6 +520,11 @@ static struct musb_hdrc_config musb_config = { .num_eps = 8, .dma_channels = 8, .gpio_vrsel = GPIO_PH6, + /* Some custom boards need to be active low, just set it to "0" + * if it is the case. + */ + .gpio_vrsel_active = 1, + .clkin = 24, /* musb CLKIN in MHZ */ }; static struct musb_hdrc_platform_data musb_plat = { @@ -347,7 +541,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, @@ -359,7 +553,146 @@ static struct platform_device musb_device = { }; #endif -#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE) +#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART +static struct resource bfin_sport0_uart_resources[] = { + { + .start = SPORT0_TCR1, + .end = SPORT0_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT0_RX, + .end = IRQ_SPORT0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT0_ERROR, + .end = IRQ_SPORT0_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport0_peripherals[] = { + P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS, + P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0 +}; + +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources), + .resource = bfin_sport0_uart_resources, + .dev = { + .platform_data = &bfin_sport0_peripherals, /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART +static struct resource bfin_sport1_uart_resources[] = { + { + .start = SPORT1_TCR1, + .end = SPORT1_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT1_RX, + .end = IRQ_SPORT1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT1_ERROR, + .end = IRQ_SPORT1_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport1_peripherals[] = { + P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS, + P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0 +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources), + .resource = bfin_sport1_uart_resources, + .dev = { + .platform_data = &bfin_sport1_peripherals, /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT2_UART +static struct resource bfin_sport2_uart_resources[] = { + { + .start = SPORT2_TCR1, + .end = SPORT2_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT2_RX, + .end = IRQ_SPORT2_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT2_ERROR, + .end = IRQ_SPORT2_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport2_peripherals[] = { + P_SPORT2_TFS, P_SPORT2_DTPRI, P_SPORT2_TSCLK, P_SPORT2_RFS, + P_SPORT2_DRPRI, P_SPORT2_RSCLK, P_SPORT2_DRSEC, P_SPORT2_DTSEC, 0 +}; + +static struct platform_device bfin_sport2_uart_device = { + .name = "bfin-sport-uart", + .id = 2, + .num_resources = ARRAY_SIZE(bfin_sport2_uart_resources), + .resource = bfin_sport2_uart_resources, + .dev = { + .platform_data = &bfin_sport2_peripherals, /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT3_UART +static struct resource bfin_sport3_uart_resources[] = { + { + .start = SPORT3_TCR1, + .end = SPORT3_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT3_RX, + .end = IRQ_SPORT3_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT3_ERROR, + .end = IRQ_SPORT3_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport3_peripherals[] = { + P_SPORT3_TFS, P_SPORT3_DTPRI, P_SPORT3_TSCLK, P_SPORT3_RFS, + P_SPORT3_DRPRI, P_SPORT3_RSCLK, P_SPORT3_DRSEC, P_SPORT3_DTSEC, 0 +}; + +static struct platform_device bfin_sport3_uart_device = { + .name = "bfin-sport-uart", + .id = 3, + .num_resources = ARRAY_SIZE(bfin_sport3_uart_resources), + .resource = bfin_sport3_uart_resources, + .dev = { + .platform_data = &bfin_sport3_peripherals, /* Passed to driver */ + }, +}; +#endif +#endif + +#if IS_ENABLED(CONFIG_PATA_BF54X) static struct resource bfin_atapi_resources[] = { { .start = 0xFFC03800, @@ -381,7 +714,7 @@ static struct platform_device bfin_atapi_device = { }; #endif -#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) +#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX) static struct mtd_partition partition_info[] = { { .name = "linux kernel(nand)", @@ -396,7 +729,6 @@ static struct mtd_partition partition_info[] = { }; static struct bf5xx_nand_platform bf5xx_nand_platform = { - .page_size = NFC_PG_SIZE_256, .data_width = NFC_NWIDTH_8, .partitions = partition_info, .nr_partitions = ARRAY_SIZE(partition_info), @@ -428,7 +760,7 @@ static struct platform_device bf5xx_nand_device = { }; #endif -#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SDH_BFIN) static struct bfin_sd_host bfin_sdh_data = { .dma_chan = CH_SDH, .irq_int0 = IRQ_SDH_MASK0, @@ -444,7 +776,45 @@ static struct platform_device bf54x_sdh_device = { }; #endif -#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +#if IS_ENABLED(CONFIG_CAN_BFIN) +static unsigned short bfin_can_peripherals[] = { + P_CAN0_RX, P_CAN0_TX, 0 +}; + +static struct resource bfin_can_resources[] = { + { + .start = 0xFFC02A00, + .end = 0xFFC02FFF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_CAN0_RX, + .end = IRQ_CAN0_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_CAN0_TX, + .end = IRQ_CAN0_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_CAN0_ERROR, + .end = IRQ_CAN0_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_can_device = { + .name = "bfin_can", + .num_resources = ARRAY_SIZE(bfin_can_resources), + .resource = bfin_can_resources, + .dev = { + .platform_data = &bfin_can_peripherals, /* Passed to driver */ + }, +}; +#endif + +#if IS_ENABLED(CONFIG_MTD_PHYSMAP) static struct mtd_partition para_partitions[] = { { .name = "bootloader(nor)", @@ -484,10 +854,9 @@ static struct platform_device para_flash_device = { }; #endif -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) /* all SPI peripherals info goes here */ -#if defined(CONFIG_MTD_M25P80) \ - || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) /* SPI flash chip (m25p16) */ static struct mtd_partition bfin_spi_flash_partitions[] = { { @@ -511,16 +880,10 @@ static struct flash_platform_data bfin_spi_flash_data = { static struct bfin5xx_spi_chip spi_flash_chip_info = { .enable_dma = 0, /* use dma transfer with this chip*/ - .bits_per_word = 8, }; #endif -#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) -static struct bfin5xx_spi_chip spi_ad7877_chip_info = { - .enable_dma = 0, - .bits_per_word = 16, -}; - +#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877) static const struct ad7877_platform_data bfin_ad7877_ts_info = { .model = 7877, .vref_delay_usecs = 50, /* internal, no capacitor */ @@ -536,16 +899,8 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = { }; #endif -#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) -static struct bfin5xx_spi_chip spidev_chip_info = { - .enable_dma = 0, - .bits_per_word = 8, -}; -#endif - static struct spi_board_info bf54x_spi_board_info[] __initdata = { -#if defined(CONFIG_MTD_M25P80) \ - || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) { /* the modalias must be the same as spi device driver name */ .modalias = "m25p80", /* Name of spi_driver for this device */ @@ -557,7 +912,7 @@ static struct spi_board_info bf54x_spi_board_info[] __initdata = { .mode = SPI_MODE_3, }, #endif -#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) +#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877) { .modalias = "ad7877", .platform_data = &bfin_ad7877_ts_info, @@ -565,16 +920,14 @@ static struct spi_board_info bf54x_spi_board_info[] __initdata = { .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, .chip_select = 2, - .controller_data = &spi_ad7877_chip_info, }, #endif -#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) +#if IS_ENABLED(CONFIG_SPI_SPIDEV) { .modalias = "spidev", .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, .chip_select = 1, - .controller_data = &spidev_chip_info, }, #endif }; @@ -619,7 +972,7 @@ static struct resource bfin_spi1_resource[] = { /* SPI controller data */ static struct bfin5xx_spi_master bf54x_spi_master_info0 = { - .num_chipselect = 3, + .num_chipselect = 4, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, }; @@ -635,7 +988,7 @@ static struct platform_device bf54x_spi_master0 = { }; static struct bfin5xx_spi_master bf54x_spi_master_info1 = { - .num_chipselect = 3, + .num_chipselect = 4, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0}, }; @@ -651,7 +1004,9 @@ static struct platform_device bf54x_spi_master1 = { }; #endif /* spi master and devices */ -#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI) +static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0}; + static struct resource bfin_twi0_resource[] = { [0] = { .start = TWI0_REGBASE, @@ -670,9 +1025,14 @@ static struct platform_device i2c_bfin_twi0_device = { .id = 0, .num_resources = ARRAY_SIZE(bfin_twi0_resource), .resource = bfin_twi0_resource, + .dev = { + .platform_data = &bfin_twi0_pins, + }, }; #if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ +static const u16 bfin_twi1_pins[] = {P_TWI1_SCL, P_TWI1_SDA, 0}; + static struct resource bfin_twi1_resource[] = { [0] = { .start = TWI1_REGBASE, @@ -691,11 +1051,14 @@ static struct platform_device i2c_bfin_twi1_device = { .id = 1, .num_resources = ARRAY_SIZE(bfin_twi1_resource), .resource = bfin_twi1_resource, + .dev = { + .platform_data = &bfin_twi1_pins, + }, }; #endif #endif -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_GPIO) #include <linux/gpio_keys.h> static struct gpio_keys_button bfin_gpio_keys_table[] = { @@ -747,15 +1110,26 @@ static struct platform_device *cm_bf548_devices[] __initdata = { &bfin_dpmc, -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +#if IS_ENABLED(CONFIG_RTC_DRV_BFIN) &rtc_device, #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) - &bfin_uart_device, +#if IS_ENABLED(CONFIG_SERIAL_BFIN) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART2 + &bfin_uart2_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART3 + &bfin_uart3_device, +#endif #endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 &bfin_sir0_device, #endif @@ -770,53 +1144,73 @@ static struct platform_device *cm_bf548_devices[] __initdata = { #endif #endif -#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE) +#if IS_ENABLED(CONFIG_FB_BF54X_LQ043) &bf54x_lq043_device, #endif -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#if IS_ENABLED(CONFIG_SMSC911X) &smsc911x_device, #endif -#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) +#if IS_ENABLED(CONFIG_USB_MUSB_HDRC) &musb_device, #endif -#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE) +#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART + &bfin_sport0_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART + &bfin_sport1_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT2_UART + &bfin_sport2_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT3_UART + &bfin_sport3_uart_device, +#endif +#endif + +#if IS_ENABLED(CONFIG_PATA_BF54X) &bfin_atapi_device, #endif -#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) +#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX) &bf5xx_nand_device, #endif -#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SDH_BFIN) &bf54x_sdh_device, #endif -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) &bf54x_spi_master0, &bf54x_spi_master1, #endif -#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_BFIN) &bf54x_kpad_device, #endif -#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI) &i2c_bfin_twi0_device, #if !defined(CONFIG_BF542) &i2c_bfin_twi1_device, #endif #endif -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_GPIO) &bfin_device_gpiokeys, #endif -#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +#if IS_ENABLED(CONFIG_MTD_PHYSMAP) ¶_flash_device, #endif + +#if IS_ENABLED(CONFIG_CAN_BFIN) + &bfin_can_device, +#endif + }; static int __init cm_bf548_init(void) @@ -824,7 +1218,7 @@ static int __init cm_bf548_init(void) printk(KERN_INFO "%s(): registering device resources\n", __func__); platform_add_devices(cm_bf548_devices, ARRAY_SIZE(cm_bf548_devices)); -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) spi_register_board_info(bf54x_spi_board_info, ARRAY_SIZE(bf54x_spi_board_info)); #endif @@ -833,3 +1227,42 @@ static int __init cm_bf548_init(void) } arch_initcall(cm_bf548_init); + +static struct platform_device *cm_bf548_early_devices[] __initdata = { +#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART2 + &bfin_uart2_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART3 + &bfin_uart3_device, +#endif +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART + &bfin_sport0_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART + &bfin_sport1_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT2_UART + &bfin_sport2_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT3_UART + &bfin_sport3_uart_device, +#endif +#endif +}; + +void __init native_machine_early_platform_add_devices(void) +{ + printk(KERN_INFO "register early platform devices\n"); + early_platform_add_devices(cm_bf548_early_devices, + ARRAY_SIZE(cm_bf548_early_devices)); +} diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c index 60193f72777..1fe7ff28661 100644 --- a/arch/blackfin/mach-bf548/boards/ezkit.c +++ b/arch/blackfin/mach-bf548/boards/ezkit.c @@ -17,11 +17,15 @@ #include <linux/i2c.h> #include <linux/interrupt.h> #include <linux/usb/musb.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinconf-generic.h> +#include <linux/platform_data/pinctrl-adi2.h> #include <asm/bfin5xx_spi.h> #include <asm/dma.h> #include <asm/gpio.h> #include <asm/nand.h> #include <asm/dpmc.h> +#include <asm/bfin_sport.h> #include <asm/portmux.h> #include <asm/bfin_sdh.h> #include <mach/bf54x_keys.h> @@ -37,7 +41,7 @@ const char bfin_board_name[] = "ADI BF548-EZKIT"; * Driver needs to know address, irq and flag pin. */ -#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_ISP1760_HCD) #include <linux/usb/isp1760.h> static struct resource bfin_isp1760_resources[] = { [0] = { @@ -72,7 +76,7 @@ static struct platform_device bfin_isp1760_device = { }; #endif -#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE) +#if IS_ENABLED(CONFIG_FB_BF54X_LQ043) #include <mach/bf54x-lq043.h> @@ -104,7 +108,7 @@ static struct platform_device bf54x_lq043_device = { }; #endif -#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_BFIN) static const unsigned int bf548_keymap[] = { KEYVAL(0, 0, KEY_ENTER), KEYVAL(0, 1, KEY_HELP), @@ -154,7 +158,7 @@ static struct platform_device bf54x_kpad_device = { }; #endif -#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE) +#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY) #include <asm/bfin_rotary.h> static struct bfin_rotary_platform_data bfin_rotary_data = { @@ -164,6 +168,7 @@ static struct bfin_rotary_platform_data bfin_rotary_data = { .rotary_button_key = KEY_ENTER, .debounce = 10, /* 0..17 */ .mode = ROT_QUAD_ENC | ROT_DEBE, + .pm_wakeup = 1, }; static struct resource bfin_rotary_resources[] = { @@ -185,7 +190,7 @@ static struct platform_device bfin_rotary_device = { }; #endif -#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE) +#if IS_ENABLED(CONFIG_INPUT_ADXL34X) #include <linux/input/adxl34x.h> static const struct adxl34x_platform_data adxl34x_info = { .x_axis_offset = 0, @@ -224,54 +229,269 @@ static const struct adxl34x_platform_data adxl34x_info = { }; #endif -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +#if IS_ENABLED(CONFIG_RTC_DRV_BFIN) static struct platform_device rtc_device = { .name = "rtc-bfin", .id = -1, }; #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) -static struct resource bfin_uart_resources[] = { +#if IS_ENABLED(CONFIG_SERIAL_BFIN) #ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { { - .start = 0xFFC00400, - .end = 0xFFC004FF, + .start = UART0_DLL, + .end = UART0_RBR+2, .flags = IORESOURCE_MEM, }, +#ifdef CONFIG_EARLY_PRINTK + { + .start = PORTE_FER, + .end = PORTE_FER+2, + .flags = IORESOURCE_REG, + }, +#endif + { + .start = IRQ_UART0_TX, + .end = IRQ_UART0_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_ERROR, + .end = IRQ_UART0_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_TX, + .end = CH_UART0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static unsigned short bfin_uart0_peripherals[] = { + P_UART0_TX, P_UART0_RX, 0 +}; + +static struct platform_device bfin_uart0_device = { + .name = "bfin-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, + .dev = { + .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ + }, +}; #endif #ifdef CONFIG_SERIAL_BFIN_UART1 +static struct resource bfin_uart1_resources[] = { { - .start = 0xFFC02000, - .end = 0xFFC020FF, + .start = UART1_DLL, + .end = UART1_RBR+2, .flags = IORESOURCE_MEM, }, +#ifdef CONFIG_EARLY_PRINTK + { + .start = PORTH_FER, + .end = PORTH_FER+2, + .flags = IORESOURCE_REG, + }, +#endif + { + .start = IRQ_UART1_TX, + .end = IRQ_UART1_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART1_ERROR, + .end = IRQ_UART1_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_TX, + .end = CH_UART1_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART1_CTSRTS + { /* CTS pin -- 0 means not supported */ + .start = GPIO_PE10, + .end = GPIO_PE10, + .flags = IORESOURCE_IO, + }, + { /* RTS pin -- 0 means not supported */ + .start = GPIO_PE9, + .end = GPIO_PE9, + .flags = IORESOURCE_IO, + }, +#endif +}; + +static unsigned short bfin_uart1_peripherals[] = { + P_UART1_TX, P_UART1_RX, +#ifdef CONFIG_BFIN_UART1_CTSRTS + P_UART1_RTS, P_UART1_CTS, +#endif + 0 +}; + +static struct platform_device bfin_uart1_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart1_resources), + .resource = bfin_uart1_resources, + .dev = { + .platform_data = &bfin_uart1_peripherals, /* Passed to driver */ + }, +}; #endif #ifdef CONFIG_SERIAL_BFIN_UART2 +static struct resource bfin_uart2_resources[] = { { - .start = 0xFFC02100, - .end = 0xFFC021FF, + .start = UART2_DLL, + .end = UART2_RBR+2, .flags = IORESOURCE_MEM, }, +#ifdef CONFIG_EARLY_PRINTK + { + .start = PORTB_FER, + .end = PORTB_FER+2, + .flags = IORESOURCE_REG, + }, +#endif + { + .start = IRQ_UART2_TX, + .end = IRQ_UART2_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART2_RX, + .end = IRQ_UART2_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART2_ERROR, + .end = IRQ_UART2_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART2_TX, + .end = CH_UART2_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART2_RX, + .end = CH_UART2_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static unsigned short bfin_uart2_peripherals[] = { + P_UART2_TX, P_UART2_RX, 0 +}; + +static struct platform_device bfin_uart2_device = { + .name = "bfin-uart", + .id = 2, + .num_resources = ARRAY_SIZE(bfin_uart2_resources), + .resource = bfin_uart2_resources, + .dev = { + .platform_data = &bfin_uart2_peripherals, /* Passed to driver */ + }, +}; #endif #ifdef CONFIG_SERIAL_BFIN_UART3 +static struct resource bfin_uart3_resources[] = { { - .start = 0xFFC03100, - .end = 0xFFC031FF, + .start = UART3_DLL, + .end = UART3_RBR+2, .flags = IORESOURCE_MEM, }, +#ifdef CONFIG_EARLY_PRINTK + { + .start = PORTB_FER, + .end = PORTB_FER+2, + .flags = IORESOURCE_REG, + }, #endif + { + .start = IRQ_UART3_TX, + .end = IRQ_UART3_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART3_RX, + .end = IRQ_UART3_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART3_ERROR, + .end = IRQ_UART3_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART3_TX, + .end = CH_UART3_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART3_RX, + .end = CH_UART3_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART3_CTSRTS + { /* CTS pin -- 0 means not supported */ + .start = GPIO_PB3, + .end = GPIO_PB3, + .flags = IORESOURCE_IO, + }, + { /* RTS pin -- 0 means not supported */ + .start = GPIO_PB2, + .end = GPIO_PB2, + .flags = IORESOURCE_IO, + }, +#endif +}; + +static unsigned short bfin_uart3_peripherals[] = { + P_UART3_TX, P_UART3_RX, +#ifdef CONFIG_BFIN_UART3_CTSRTS + P_UART3_RTS, P_UART3_CTS, +#endif + 0 }; -static struct platform_device bfin_uart_device = { +static struct platform_device bfin_uart3_device = { .name = "bfin-uart", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_uart_resources), - .resource = bfin_uart_resources, + .id = 3, + .num_resources = ARRAY_SIZE(bfin_uart3_resources), + .resource = bfin_uart3_resources, + .dev = { + .platform_data = &bfin_uart3_peripherals, /* Passed to driver */ + }, }; #endif +#endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 static struct resource bfin_sir0_resources[] = { { @@ -374,7 +594,7 @@ static struct platform_device bfin_sir3_device = { #endif #endif -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#if IS_ENABLED(CONFIG_SMSC911X) #include <linux/smsc911x.h> static struct resource smsc911x_resources[] = { @@ -409,7 +629,7 @@ static struct platform_device smsc911x_device = { }; #endif -#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) +#if IS_ENABLED(CONFIG_USB_MUSB_HDRC) static struct resource musb_resources[] = { [0] = { .start = 0xFFC03C00, @@ -420,11 +640,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -436,12 +658,17 @@ static struct musb_hdrc_config musb_config = { .num_eps = 8, .dma_channels = 8, .gpio_vrsel = GPIO_PE7, + /* Some custom boards need to be active low, just set it to "0" + * if it is the case. + */ + .gpio_vrsel_active = 1, + .clkin = 24, /* musb CLKIN in MHZ */ }; static struct musb_hdrc_platform_data musb_plat = { -#if defined(CONFIG_USB_MUSB_OTG) +#if defined(CONFIG_USB_MUSB_HDRC) && defined(CONFIG_USB_GADGET_MUSB_HDRC) .mode = MUSB_OTG, -#elif defined(CONFIG_USB_MUSB_HDRC_HCD) +#elif defined(CONFIG_USB_MUSB_HDRC) .mode = MUSB_HOST, #elif defined(CONFIG_USB_GADGET_MUSB_HDRC) .mode = MUSB_PERIPHERAL, @@ -452,7 +679,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, @@ -464,12 +691,152 @@ static struct platform_device musb_device = { }; #endif -#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE) -unsigned short bfin_can_peripherals[] = { +#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART +static struct resource bfin_sport0_uart_resources[] = { + { + .start = SPORT0_TCR1, + .end = SPORT0_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT0_RX, + .end = IRQ_SPORT0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT0_ERROR, + .end = IRQ_SPORT0_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport0_peripherals[] = { + P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS, + P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0 +}; + +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources), + .resource = bfin_sport0_uart_resources, + .dev = { + .platform_data = &bfin_sport0_peripherals, /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART +static struct resource bfin_sport1_uart_resources[] = { + { + .start = SPORT1_TCR1, + .end = SPORT1_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT1_RX, + .end = IRQ_SPORT1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT1_ERROR, + .end = IRQ_SPORT1_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport1_peripherals[] = { + P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS, + P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0 +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources), + .resource = bfin_sport1_uart_resources, + .dev = { + .platform_data = &bfin_sport1_peripherals, /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT2_UART +static struct resource bfin_sport2_uart_resources[] = { + { + .start = SPORT2_TCR1, + .end = SPORT2_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT2_RX, + .end = IRQ_SPORT2_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT2_ERROR, + .end = IRQ_SPORT2_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport2_peripherals[] = { + P_SPORT2_TFS, P_SPORT2_DTPRI, P_SPORT2_TSCLK, P_SPORT2_RFS, + P_SPORT2_DRPRI, P_SPORT2_RSCLK, P_SPORT2_DRSEC, P_SPORT2_DTSEC, 0 +}; + +static struct platform_device bfin_sport2_uart_device = { + .name = "bfin-sport-uart", + .id = 2, + .num_resources = ARRAY_SIZE(bfin_sport2_uart_resources), + .resource = bfin_sport2_uart_resources, + .dev = { + .platform_data = &bfin_sport2_peripherals, /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT3_UART +static struct resource bfin_sport3_uart_resources[] = { + { + .start = SPORT3_TCR1, + .end = SPORT3_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT3_RX, + .end = IRQ_SPORT3_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT3_ERROR, + .end = IRQ_SPORT3_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static unsigned short bfin_sport3_peripherals[] = { + P_SPORT3_TFS, P_SPORT3_DTPRI, P_SPORT3_TSCLK, P_SPORT3_RFS, + P_SPORT3_DRPRI, P_SPORT3_RSCLK, P_SPORT3_DRSEC, P_SPORT3_DTSEC, 0 +}; + +static struct platform_device bfin_sport3_uart_device = { + .name = "bfin-sport-uart", + .id = 3, + .num_resources = ARRAY_SIZE(bfin_sport3_uart_resources), + .resource = bfin_sport3_uart_resources, + .dev = { + .platform_data = &bfin_sport3_peripherals, /* Passed to driver */ + }, +}; +#endif +#endif + +#if IS_ENABLED(CONFIG_CAN_BFIN) + +static unsigned short bfin_can0_peripherals[] = { P_CAN0_RX, P_CAN0_TX, 0 }; -static struct resource bfin_can_resources[] = { +static struct resource bfin_can0_resources[] = { { .start = 0xFFC02A00, .end = 0xFFC02FFF, @@ -492,17 +859,56 @@ static struct resource bfin_can_resources[] = { }, }; -static struct platform_device bfin_can_device = { +static struct platform_device bfin_can0_device = { .name = "bfin_can", - .num_resources = ARRAY_SIZE(bfin_can_resources), - .resource = bfin_can_resources, + .id = 0, + .num_resources = ARRAY_SIZE(bfin_can0_resources), + .resource = bfin_can0_resources, .dev = { - .platform_data = &bfin_can_peripherals, /* Passed to driver */ + .platform_data = &bfin_can0_peripherals, /* Passed to driver */ }, }; + +static unsigned short bfin_can1_peripherals[] = { + P_CAN1_RX, P_CAN1_TX, 0 +}; + +static struct resource bfin_can1_resources[] = { + { + .start = 0xFFC03200, + .end = 0xFFC037FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_CAN1_RX, + .end = IRQ_CAN1_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_CAN1_TX, + .end = IRQ_CAN1_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_CAN1_ERROR, + .end = IRQ_CAN1_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_can1_device = { + .name = "bfin_can", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_can1_resources), + .resource = bfin_can1_resources, + .dev = { + .platform_data = &bfin_can1_peripherals, /* Passed to driver */ + }, +}; + #endif -#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE) +#if IS_ENABLED(CONFIG_PATA_BF54X) static struct resource bfin_atapi_resources[] = { { .start = 0xFFC03800, @@ -524,11 +930,15 @@ static struct platform_device bfin_atapi_device = { }; #endif -#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) +#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX) static struct mtd_partition partition_info[] = { { - .name = "linux kernel(nand)", + .name = "bootloader(nand)", .offset = 0, + .size = 0x80000, + }, { + .name = "linux kernel(nand)", + .offset = MTDPART_OFS_APPEND, .size = 4 * 1024 * 1024, }, { @@ -539,7 +949,6 @@ static struct mtd_partition partition_info[] = { }; static struct bf5xx_nand_platform bf5xx_nand_platform = { - .page_size = NFC_PG_SIZE_256, .data_width = NFC_NWIDTH_8, .partitions = partition_info, .nr_partitions = ARRAY_SIZE(partition_info), @@ -571,7 +980,7 @@ static struct platform_device bf5xx_nand_device = { }; #endif -#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SDH_BFIN) static struct bfin_sd_host bfin_sdh_data = { .dma_chan = CH_SDH, @@ -588,11 +997,11 @@ static struct platform_device bf54x_sdh_device = { }; #endif -#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +#if IS_ENABLED(CONFIG_MTD_PHYSMAP) static struct mtd_partition ezkit_partitions[] = { { .name = "bootloader(nor)", - .size = 0x40000, + .size = 0x80000, .offset = 0, }, { .name = "linux kernel(nor)", @@ -600,7 +1009,15 @@ static struct mtd_partition ezkit_partitions[] = { .offset = MTDPART_OFS_APPEND, }, { .name = "file system(nor)", - .size = MTDPART_SIZ_FULL, + .size = 0x1000000 - 0x80000 - 0x400000 - 0x8000 * 4, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "config(nor)", + .size = 0x8000 * 3, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "u-boot env(nor)", + .size = 0x8000, .offset = MTDPART_OFS_APPEND, } }; @@ -628,13 +1045,12 @@ static struct platform_device ezkit_flash_device = { }; #endif -#if defined(CONFIG_MTD_M25P80) \ - || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) /* SPI flash chip (m25p16) */ static struct mtd_partition bfin_spi_flash_partitions[] = { { .name = "bootloader(spi)", - .size = 0x00040000, + .size = 0x00080000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { @@ -653,24 +1069,10 @@ static struct flash_platform_data bfin_spi_flash_data = { static struct bfin5xx_spi_chip spi_flash_chip_info = { .enable_dma = 0, /* use dma transfer with this chip*/ - .bits_per_word = 8, }; #endif -#if defined(CONFIG_SND_BLACKFIN_AD1836) \ - || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) -static struct bfin5xx_spi_chip ad1836_spi_chip_info = { - .enable_dma = 0, - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) -static struct bfin5xx_spi_chip spi_ad7877_chip_info = { - .enable_dma = 0, - .bits_per_word = 16, -}; - +#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877) static const struct ad7877_platform_data bfin_ad7877_ts_info = { .model = 7877, .vref_delay_usecs = 50, /* internal, no capacitor */ @@ -686,78 +1088,463 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = { }; #endif -#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) -static struct bfin5xx_spi_chip spidev_chip_info = { - .enable_dma = 0, - .bits_per_word = 8, +#ifdef CONFIG_PINCTRL_ADI2 + +# define ADI_PINT_DEVNAME "adi-gpio-pint" +# define ADI_GPIO_DEVNAME "adi-gpio" +# define ADI_PINCTRL_DEVNAME "pinctrl-adi2" + +static struct platform_device bfin_pinctrl_device = { + .name = ADI_PINCTRL_DEVNAME, + .id = 0, }; -#endif -#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE) -static struct bfin5xx_spi_chip spi_adxl34x_chip_info = { - .enable_dma = 0, /* use dma transfer with this chip*/ - .bits_per_word = 8, +static struct resource bfin_pint0_resources[] = { + { + .start = PINT0_MASK_SET, + .end = PINT0_LATCH + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PINT0, + .end = IRQ_PINT0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pint0_device = { + .name = ADI_PINT_DEVNAME, + .id = 0, + .num_resources = ARRAY_SIZE(bfin_pint0_resources), + .resource = bfin_pint0_resources, +}; + +static struct resource bfin_pint1_resources[] = { + { + .start = PINT1_MASK_SET, + .end = PINT1_LATCH + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PINT1, + .end = IRQ_PINT1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pint1_device = { + .name = ADI_PINT_DEVNAME, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_pint1_resources), + .resource = bfin_pint1_resources, }; + +static struct resource bfin_pint2_resources[] = { + { + .start = PINT2_MASK_SET, + .end = PINT2_LATCH + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PINT2, + .end = IRQ_PINT2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pint2_device = { + .name = ADI_PINT_DEVNAME, + .id = 2, + .num_resources = ARRAY_SIZE(bfin_pint2_resources), + .resource = bfin_pint2_resources, +}; + +static struct resource bfin_pint3_resources[] = { + { + .start = PINT3_MASK_SET, + .end = PINT3_LATCH + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PINT3, + .end = IRQ_PINT3, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pint3_device = { + .name = ADI_PINT_DEVNAME, + .id = 3, + .num_resources = ARRAY_SIZE(bfin_pint3_resources), + .resource = bfin_pint3_resources, +}; + +static struct resource bfin_gpa_resources[] = { + { + .start = PORTA_FER, + .end = PORTA_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { /* optional */ + .start = IRQ_PA0, + .end = IRQ_PA0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpa_pdata = { + .port_gpio_base = GPIO_PA0, /* Optional */ + .port_pin_base = GPIO_PA0, + .port_width = GPIO_BANKSIZE, + .pint_id = 0, /* PINT0 */ + .pint_assign = true, /* PINT upper 16 bit */ + .pint_map = 0, /* mapping mask in PINT */ +}; + +static struct platform_device bfin_gpa_device = { + .name = ADI_GPIO_DEVNAME, + .id = 0, + .num_resources = ARRAY_SIZE(bfin_gpa_resources), + .resource = bfin_gpa_resources, + .dev = { + .platform_data = &bfin_gpa_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpb_resources[] = { + { + .start = PORTB_FER, + .end = PORTB_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PB0, + .end = IRQ_PB0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpb_pdata = { + .port_gpio_base = GPIO_PB0, + .port_pin_base = GPIO_PB0, + .port_width = 15, + .pint_id = 0, + .pint_assign = true, + .pint_map = 1, +}; + +static struct platform_device bfin_gpb_device = { + .name = ADI_GPIO_DEVNAME, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_gpb_resources), + .resource = bfin_gpb_resources, + .dev = { + .platform_data = &bfin_gpb_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpc_resources[] = { + { + .start = PORTC_FER, + .end = PORTC_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PC0, + .end = IRQ_PC0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpc_pdata = { + .port_gpio_base = GPIO_PC0, + .port_pin_base = GPIO_PC0, + .port_width = 14, + .pint_id = 2, + .pint_assign = true, + .pint_map = 0, +}; + +static struct platform_device bfin_gpc_device = { + .name = ADI_GPIO_DEVNAME, + .id = 2, + .num_resources = ARRAY_SIZE(bfin_gpc_resources), + .resource = bfin_gpc_resources, + .dev = { + .platform_data = &bfin_gpc_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpd_resources[] = { + { + .start = PORTD_FER, + .end = PORTD_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PD0, + .end = IRQ_PD0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpd_pdata = { + .port_gpio_base = GPIO_PD0, + .port_pin_base = GPIO_PD0, + .port_width = GPIO_BANKSIZE, + .pint_id = 2, + .pint_assign = false, + .pint_map = 1, +}; + +static struct platform_device bfin_gpd_device = { + .name = ADI_GPIO_DEVNAME, + .id = 3, + .num_resources = ARRAY_SIZE(bfin_gpd_resources), + .resource = bfin_gpd_resources, + .dev = { + .platform_data = &bfin_gpd_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpe_resources[] = { + { + .start = PORTE_FER, + .end = PORTE_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PE0, + .end = IRQ_PE0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpe_pdata = { + .port_gpio_base = GPIO_PE0, + .port_pin_base = GPIO_PE0, + .port_width = GPIO_BANKSIZE, + .pint_id = 3, + .pint_assign = true, + .pint_map = 2, +}; + +static struct platform_device bfin_gpe_device = { + .name = ADI_GPIO_DEVNAME, + .id = 4, + .num_resources = ARRAY_SIZE(bfin_gpe_resources), + .resource = bfin_gpe_resources, + .dev = { + .platform_data = &bfin_gpe_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpf_resources[] = { + { + .start = PORTF_FER, + .end = PORTF_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PF0, + .end = IRQ_PF0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpf_pdata = { + .port_gpio_base = GPIO_PF0, + .port_pin_base = GPIO_PF0, + .port_width = GPIO_BANKSIZE, + .pint_id = 3, + .pint_assign = false, + .pint_map = 3, +}; + +static struct platform_device bfin_gpf_device = { + .name = ADI_GPIO_DEVNAME, + .id = 5, + .num_resources = ARRAY_SIZE(bfin_gpf_resources), + .resource = bfin_gpf_resources, + .dev = { + .platform_data = &bfin_gpf_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpg_resources[] = { + { + .start = PORTG_FER, + .end = PORTG_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PG0, + .end = IRQ_PG0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpg_pdata = { + .port_gpio_base = GPIO_PG0, + .port_pin_base = GPIO_PG0, + .port_width = GPIO_BANKSIZE, + .pint_id = -1, +}; + +static struct platform_device bfin_gpg_device = { + .name = ADI_GPIO_DEVNAME, + .id = 6, + .num_resources = ARRAY_SIZE(bfin_gpg_resources), + .resource = bfin_gpg_resources, + .dev = { + .platform_data = &bfin_gpg_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gph_resources[] = { + { + .start = PORTH_FER, + .end = PORTH_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PH0, + .end = IRQ_PH0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gph_pdata = { + .port_gpio_base = GPIO_PH0, + .port_pin_base = GPIO_PH0, + .port_width = 14, + .pint_id = -1, +}; + +static struct platform_device bfin_gph_device = { + .name = ADI_GPIO_DEVNAME, + .id = 7, + .num_resources = ARRAY_SIZE(bfin_gph_resources), + .resource = bfin_gph_resources, + .dev = { + .platform_data = &bfin_gph_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpi_resources[] = { + { + .start = PORTI_FER, + .end = PORTI_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PI0, + .end = IRQ_PI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpi_pdata = { + .port_gpio_base = GPIO_PI0, + .port_pin_base = GPIO_PI0, + .port_width = GPIO_BANKSIZE, + .pint_id = -1, +}; + +static struct platform_device bfin_gpi_device = { + .name = ADI_GPIO_DEVNAME, + .id = 8, + .num_resources = ARRAY_SIZE(bfin_gpi_resources), + .resource = bfin_gpi_resources, + .dev = { + .platform_data = &bfin_gpi_pdata, /* Passed to driver */ + }, +}; + +static struct resource bfin_gpj_resources[] = { + { + .start = PORTJ_FER, + .end = PORTJ_MUX + 3, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_PJ0, + .end = IRQ_PJ0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct adi_pinctrl_gpio_platform_data bfin_gpj_pdata = { + .port_gpio_base = GPIO_PJ0, + .port_pin_base = GPIO_PJ0, + .port_width = 14, + .pint_id = -1, +}; + +static struct platform_device bfin_gpj_device = { + .name = ADI_GPIO_DEVNAME, + .id = 9, + .num_resources = ARRAY_SIZE(bfin_gpj_resources), + .resource = bfin_gpj_resources, + .dev = { + .platform_data = &bfin_gpj_pdata, /* Passed to driver */ + }, +}; + #endif static struct spi_board_info bfin_spi_board_info[] __initdata = { -#if defined(CONFIG_MTD_M25P80) \ - || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) { /* the modalias must be the same as spi device driver name */ .modalias = "m25p80", /* Name of spi_driver for this device */ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, /* Framework bus number */ - .chip_select = 1, /* SPI_SSEL1*/ + .chip_select = MAX_CTRL_CS + GPIO_PE4, /* SPI_SSEL1*/ .platform_data = &bfin_spi_flash_data, .controller_data = &spi_flash_chip_info, .mode = SPI_MODE_3, }, #endif -#if defined(CONFIG_SND_BLACKFIN_AD1836) \ - || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X) { - .modalias = "ad1836", + .modalias = "ad183x", .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ .bus_num = 1, - .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, - .controller_data = &ad1836_spi_chip_info, + .chip_select = MAX_CTRL_CS + GPIO_PG6, /* SPI_SSEL2 */ }, #endif -#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) +#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877) { .modalias = "ad7877", .platform_data = &bfin_ad7877_ts_info, .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, - .chip_select = 2, - .controller_data = &spi_ad7877_chip_info, + .chip_select = MAX_CTRL_CS + GPIO_PE5, /* SPI_SSEL2 */ }, #endif -#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) +#if IS_ENABLED(CONFIG_SPI_SPIDEV) { .modalias = "spidev", .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, - .chip_select = 1, - .controller_data = &spidev_chip_info, + .chip_select = MAX_CTRL_CS + GPIO_PE4, /* SPI_SSEL1 */ }, #endif -#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE) +#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI) { .modalias = "adxl34x", .platform_data = &adxl34x_info, .irq = IRQ_PC5, .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 1, - .chip_select = 2, - .controller_data = &spi_adxl34x_chip_info, + .chip_select = MAX_CTRL_CS + GPIO_PG6, /* SPI_SSEL2 */ .mode = SPI_MODE_3, }, #endif }; -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) /* SPI (0) */ static struct resource bfin_spi0_resource[] = { [0] = { @@ -798,7 +1585,7 @@ static struct resource bfin_spi1_resource[] = { /* SPI controller data */ static struct bfin5xx_spi_master bf54x_spi_master_info0 = { - .num_chipselect = 3, + .num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, }; @@ -814,7 +1601,7 @@ static struct platform_device bf54x_spi_master0 = { }; static struct bfin5xx_spi_master bf54x_spi_master_info1 = { - .num_chipselect = 3, + .num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0}, }; @@ -830,7 +1617,74 @@ static struct platform_device bf54x_spi_master1 = { }; #endif /* spi master and devices */ -#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE) +#include <linux/videodev2.h> +#include <media/blackfin/bfin_capture.h> +#include <media/blackfin/ppi.h> + +static const unsigned short ppi_req[] = { + P_PPI1_D0, P_PPI1_D1, P_PPI1_D2, P_PPI1_D3, + P_PPI1_D4, P_PPI1_D5, P_PPI1_D6, P_PPI1_D7, + P_PPI1_CLK, P_PPI1_FS1, P_PPI1_FS2, + 0, +}; + +static const struct ppi_info ppi_info = { + .type = PPI_TYPE_EPPI, + .dma_ch = CH_EPPI1, + .irq_err = IRQ_EPPI1_ERROR, + .base = (void __iomem *)EPPI1_STATUS, + .pin_req = ppi_req, +}; + +#if IS_ENABLED(CONFIG_VIDEO_VS6624) +static struct v4l2_input vs6624_inputs[] = { + { + .index = 0, + .name = "Camera", + .type = V4L2_INPUT_TYPE_CAMERA, + .std = V4L2_STD_UNKNOWN, + }, +}; + +static struct bcap_route vs6624_routes[] = { + { + .input = 0, + .output = 0, + }, +}; + +static const unsigned vs6624_ce_pin = GPIO_PG6; + +static struct bfin_capture_config bfin_capture_data = { + .card_name = "BF548", + .inputs = vs6624_inputs, + .num_inputs = ARRAY_SIZE(vs6624_inputs), + .routes = vs6624_routes, + .i2c_adapter_id = 0, + .board_info = { + .type = "vs6624", + .addr = 0x10, + .platform_data = (void *)&vs6624_ce_pin, + }, + .ppi_info = &ppi_info, + .ppi_control = (POLC | PACKEN | DLEN_8 | XFR_TYPE | 0x20), + .int_mask = 0xFFFFFFFF, /* disable error interrupt on eppi */ + .blank_clocks = 8, /* 8 clocks as SAV and EAV */ +}; +#endif + +static struct platform_device bfin_capture_device = { + .name = "bfin_capture", + .dev = { + .platform_data = &bfin_capture_data, + }, +}; +#endif + +#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI) +static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0}; + static struct resource bfin_twi0_resource[] = { [0] = { .start = TWI0_REGBASE, @@ -849,9 +1703,14 @@ static struct platform_device i2c_bfin_twi0_device = { .id = 0, .num_resources = ARRAY_SIZE(bfin_twi0_resource), .resource = bfin_twi0_resource, + .dev = { + .platform_data = &bfin_twi0_pins, + }, }; #if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ +static const u16 bfin_twi1_pins[] = {P_TWI1_SCL, P_TWI1_SDA, 0}; + static struct resource bfin_twi1_resource[] = { [0] = { .start = TWI1_REGBASE, @@ -870,37 +1729,50 @@ static struct platform_device i2c_bfin_twi1_device = { .id = 1, .num_resources = ARRAY_SIZE(bfin_twi1_resource), .resource = bfin_twi1_resource, + .dev = { + .platform_data = &bfin_twi1_pins, + }, }; #endif #endif static struct i2c_board_info __initdata bfin_i2c_board_info0[] = { +#if IS_ENABLED(CONFIG_SND_SOC_SSM2602) + { + I2C_BOARD_INFO("ssm2602", 0x1b), + }, +#endif }; #if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = { -#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE) +#if IS_ENABLED(CONFIG_BFIN_TWI_LCD) { I2C_BOARD_INFO("pcf8574_lcd", 0x22), }, #endif -#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE) +#if IS_ENABLED(CONFIG_INPUT_PCF8574) { I2C_BOARD_INFO("pcf8574_keypad", 0x27), .irq = 212, }, #endif -#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE) +#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C) { I2C_BOARD_INFO("adxl34x", 0x53), .irq = IRQ_PC5, .platform_data = (void *)&adxl34x_info, }, #endif +#if IS_ENABLED(CONFIG_BFIN_TWI_LCD) + { + I2C_BOARD_INFO("ad5252", 0x2f), + }, +#endif }; #endif -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_GPIO) #include <linux/gpio_keys.h> static struct gpio_keys_button bfin_gpio_keys_table[] = { @@ -951,19 +1823,160 @@ static struct platform_device bfin_dpmc = { }, }; +#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \ + IS_ENABLED(CONFIG_SND_BF5XX_AC97) + +#define SPORT_REQ(x) \ + [x] = {P_SPORT##x##_TFS, P_SPORT##x##_DTPRI, P_SPORT##x##_TSCLK, \ + P_SPORT##x##_RFS, P_SPORT##x##_DRPRI, P_SPORT##x##_RSCLK, 0} + +static const u16 bfin_snd_pin[][7] = { + SPORT_REQ(0), + SPORT_REQ(1), + SPORT_REQ(2), + SPORT_REQ(3), +}; + +static struct bfin_snd_platform_data bfin_snd_data[] = { + { + .pin_req = &bfin_snd_pin[0][0], + }, + { + .pin_req = &bfin_snd_pin[1][0], + }, + { + .pin_req = &bfin_snd_pin[2][0], + }, + { + .pin_req = &bfin_snd_pin[3][0], + }, +}; + +#define BFIN_SND_RES(x) \ + [x] = { \ + { \ + .start = SPORT##x##_TCR1, \ + .end = SPORT##x##_TCR1, \ + .flags = IORESOURCE_MEM \ + }, \ + { \ + .start = CH_SPORT##x##_RX, \ + .end = CH_SPORT##x##_RX, \ + .flags = IORESOURCE_DMA, \ + }, \ + { \ + .start = CH_SPORT##x##_TX, \ + .end = CH_SPORT##x##_TX, \ + .flags = IORESOURCE_DMA, \ + }, \ + { \ + .start = IRQ_SPORT##x##_ERROR, \ + .end = IRQ_SPORT##x##_ERROR, \ + .flags = IORESOURCE_IRQ, \ + } \ + } + +static struct resource bfin_snd_resources[][4] = { + BFIN_SND_RES(0), + BFIN_SND_RES(1), + BFIN_SND_RES(2), + BFIN_SND_RES(3), +}; +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) +static struct platform_device bfin_i2s_pcm = { + .name = "bfin-i2s-pcm-audio", + .id = -1, +}; +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_AC97) +static struct platform_device bfin_ac97_pcm = { + .name = "bfin-ac97-pcm-audio", + .id = -1, +}; +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311) +static struct platform_device bfin_ad73311_codec_device = { + .name = "ad73311", + .id = -1, +}; +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1980) +static struct platform_device bfin_ad1980_codec_device = { + .name = "ad1980", + .id = -1, +}; +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S) +static struct platform_device bfin_i2s = { + .name = "bfin-i2s", + .id = CONFIG_SND_BF5XX_SPORT_NUM, + .num_resources = ARRAY_SIZE(bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM]), + .resource = bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM], + .dev = { + .platform_data = &bfin_snd_data[CONFIG_SND_BF5XX_SPORT_NUM], + }, +}; +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97) +static struct platform_device bfin_ac97 = { + .name = "bfin-ac97", + .id = CONFIG_SND_BF5XX_SPORT_NUM, + .num_resources = ARRAY_SIZE(bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM]), + .resource = bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM], + .dev = { + .platform_data = &bfin_snd_data[CONFIG_SND_BF5XX_SPORT_NUM], + }, +}; +#endif + static struct platform_device *ezkit_devices[] __initdata = { &bfin_dpmc, - -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +#if defined(CONFIG_PINCTRL_ADI2) + &bfin_pinctrl_device, + &bfin_pint0_device, + &bfin_pint1_device, + &bfin_pint2_device, + &bfin_pint3_device, + &bfin_gpa_device, + &bfin_gpb_device, + &bfin_gpc_device, + &bfin_gpd_device, + &bfin_gpe_device, + &bfin_gpf_device, + &bfin_gpg_device, + &bfin_gph_device, + &bfin_gpi_device, + &bfin_gpj_device, +#endif + +#if IS_ENABLED(CONFIG_RTC_DRV_BFIN) &rtc_device, #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) - &bfin_uart_device, +#if IS_ENABLED(CONFIG_SERIAL_BFIN) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART2 + &bfin_uart2_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART3 + &bfin_uart3_device, +#endif #endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 &bfin_sir0_device, #endif @@ -978,71 +1991,168 @@ static struct platform_device *ezkit_devices[] __initdata = { #endif #endif -#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE) +#if IS_ENABLED(CONFIG_FB_BF54X_LQ043) &bf54x_lq043_device, #endif -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#if IS_ENABLED(CONFIG_SMSC911X) &smsc911x_device, #endif -#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) +#if IS_ENABLED(CONFIG_USB_MUSB_HDRC) &musb_device, #endif -#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_ISP1760_HCD) &bfin_isp1760_device, #endif -#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE) - &bfin_can_device, +#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART + &bfin_sport0_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART + &bfin_sport1_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT2_UART + &bfin_sport2_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT3_UART + &bfin_sport3_uart_device, +#endif +#endif + +#if IS_ENABLED(CONFIG_CAN_BFIN) + &bfin_can0_device, + &bfin_can1_device, #endif -#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE) +#if IS_ENABLED(CONFIG_PATA_BF54X) &bfin_atapi_device, #endif -#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) +#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX) &bf5xx_nand_device, #endif -#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SDH_BFIN) &bf54x_sdh_device, #endif -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) &bf54x_spi_master0, &bf54x_spi_master1, #endif +#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE) + &bfin_capture_device, +#endif -#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_BFIN) &bf54x_kpad_device, #endif -#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE) +#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY) &bfin_rotary_device, #endif -#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI) &i2c_bfin_twi0_device, #if !defined(CONFIG_BF542) &i2c_bfin_twi1_device, #endif #endif -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_GPIO) &bfin_device_gpiokeys, #endif -#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) +#if IS_ENABLED(CONFIG_MTD_PHYSMAP) &ezkit_flash_device, #endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) + &bfin_i2s_pcm, +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_AC97) + &bfin_ac97_pcm, +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1980) + &bfin_ad1980_codec_device, +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) + &bfin_i2s, +#endif + +#if IS_ENABLED(CONFIG_SND_BF5XX_AC97) + &bfin_ac97, +#endif +}; + +/* Pin control settings */ +static struct pinctrl_map __initdata bfin_pinmux_map[] = { + /* per-device maps */ + PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.0", "pinctrl-adi2.0", NULL, "uart0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.1", "pinctrl-adi2.0", NULL, "uart1"), +#ifdef CONFIG_BFIN_UART1_CTSRTS + PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.1", "pinctrl-adi2.0", NULL, "uart1_ctsrts"), +#endif + PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.2", "pinctrl-adi2.0", NULL, "uart2"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.3", "pinctrl-adi2.0", NULL, "uart3"), +#ifdef CONFIG_BFIN_UART3_CTSRTS + PIN_MAP_MUX_GROUP_DEFAULT("bfin-uart.3", "pinctrl-adi2.0", NULL, "uart3_ctsrts"), +#endif + PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.0", "pinctrl-adi2.0", NULL, "uart0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.1", "pinctrl-adi2.0", NULL, "uart1"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.2", "pinctrl-adi2.0", NULL, "uart2"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.3", "pinctrl-adi2.0", NULL, "uart3"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-sdh.0", "pinctrl-adi2.0", NULL, "rsi0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-spi.0", "pinctrl-adi2.0", NULL, "spi0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-spi.1", "pinctrl-adi2.0", NULL, "spi1"), + PIN_MAP_MUX_GROUP_DEFAULT("i2c-bfin-twi.0", "pinctrl-adi2.0", NULL, "twi0"), +#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ + PIN_MAP_MUX_GROUP_DEFAULT("i2c-bfin-twi.1", "pinctrl-adi2.0", NULL, "twi1"), +#endif + PIN_MAP_MUX_GROUP_DEFAULT("bfin-rotary", "pinctrl-adi2.0", NULL, "rotary"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin_can.0", "pinctrl-adi2.0", NULL, "can0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin_can.1", "pinctrl-adi2.0", NULL, "can1"), + PIN_MAP_MUX_GROUP_DEFAULT("bf54x-lq043", "pinctrl-adi2.0", "ppi0_24bgrp", "ppi0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.0", "pinctrl-adi2.0", NULL, "sport0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.0", "pinctrl-adi2.0", NULL, "sport0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-ac97.0", "pinctrl-adi2.0", NULL, "sport0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.1", "pinctrl-adi2.0", NULL, "sport1"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.1", "pinctrl-adi2.0", NULL, "sport1"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-ac97.1", "pinctrl-adi2.0", NULL, "sport1"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.2", "pinctrl-adi2.0", NULL, "sport2"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.2", "pinctrl-adi2.0", NULL, "sport2"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-ac97.2", "pinctrl-adi2.0", NULL, "sport2"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-i2s.3", "pinctrl-adi2.0", NULL, "sport3"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-tdm.3", "pinctrl-adi2.0", NULL, "sport3"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-ac97.3", "pinctrl-adi2.0", NULL, "sport3"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-sport-uart.0", "pinctrl-adi2.0", NULL, "sport0"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-sport-uart.1", "pinctrl-adi2.0", NULL, "sport1"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-sport-uart.2", "pinctrl-adi2.0", NULL, "sport2"), + PIN_MAP_MUX_GROUP_DEFAULT("bfin-sport-uart.3", "pinctrl-adi2.0", NULL, "sport3"), + PIN_MAP_MUX_GROUP_DEFAULT("pata-bf54x", "pinctrl-adi2.0", NULL, "atapi"), +#ifdef CONFIG_BF548_ATAPI_ALTERNATIVE_PORT + PIN_MAP_MUX_GROUP_DEFAULT("pata-bf54x", "pinctrl-adi2.0", NULL, "atapi_alter"), +#endif + PIN_MAP_MUX_GROUP_DEFAULT("bf5xx-nand.0", "pinctrl-adi2.0", NULL, "nfc0"), + PIN_MAP_MUX_GROUP_DEFAULT("bf54x-keys", "pinctrl-adi2.0", "keys_4x4grp", "keys"), + PIN_MAP_MUX_GROUP("bf54x-keys", "4bit", "pinctrl-adi2.0", "keys_4x4grp", "keys"), + PIN_MAP_MUX_GROUP("bf54x-keys", "8bit", "pinctrl-adi2.0", "keys_8x8grp", "keys"), }; static int __init ezkit_init(void) { printk(KERN_INFO "%s(): registering device resources\n", __func__); + /* Initialize pinmuxing */ + pinctrl_register_mappings(bfin_pinmux_map, + ARRAY_SIZE(bfin_pinmux_map)); + i2c_register_board_info(0, bfin_i2c_board_info0, ARRAY_SIZE(bfin_i2c_board_info0)); #if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */ @@ -1058,3 +2168,27 @@ static int __init ezkit_init(void) } arch_initcall(ezkit_init); + +static struct platform_device *ezkit_early_devices[] __initdata = { +#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART2 + &bfin_uart2_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART3 + &bfin_uart3_device, +#endif +#endif +}; + +void __init native_machine_early_platform_add_devices(void) +{ + printk(KERN_INFO "register early platform devices\n"); + early_platform_add_devices(ezkit_early_devices, + ARRAY_SIZE(ezkit_early_devices)); +} diff --git a/arch/blackfin/mach-bf548/dma.c b/arch/blackfin/mach-bf548/dma.c index 039a6d9d38f..69ead33cbf9 100644 --- a/arch/blackfin/mach-bf548/dma.c +++ b/arch/blackfin/mach-bf548/dma.c @@ -11,7 +11,7 @@ #include <asm/blackfin.h> #include <asm/dma.h> -struct dma_register *dma_io_base_addr[MAX_DMA_CHANNELS] = { +struct dma_register * const dma_io_base_addr[MAX_DMA_CHANNELS] = { (struct dma_register *) DMA0_NEXT_DESC_PTR, (struct dma_register *) DMA1_NEXT_DESC_PTR, (struct dma_register *) DMA2_NEXT_DESC_PTR, @@ -63,6 +63,7 @@ int channel2irq(unsigned int channel) break; case CH_SPORT1_TX: ret_irq = IRQ_SPORT1_TX; + break; case CH_SPI0: ret_irq = IRQ_SPI0; break; diff --git a/arch/blackfin/mach-bf548/include/mach/anomaly.h b/arch/blackfin/mach-bf548/include/mach/anomaly.h index 7d08c752449..098fad63e03 100644 --- a/arch/blackfin/mach-bf548/include/mach/anomaly.h +++ b/arch/blackfin/mach-bf548/include/mach/anomaly.h @@ -5,13 +5,12 @@ * and can be replaced with that version at any time * DO NOT EDIT THIS FILE * - * Copyright 2004-2009 Analog Devices Inc. - * Licensed under the ADI BSD license. - * https://docs.blackfin.uclinux.org/doku.php?id=adi_bsd + * Copyright 2004-2011 Analog Devices Inc. + * Licensed under the Clear BSD license. */ /* This file should be up to date with: - * - Revision I, 07/23/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List + * - Revision K, 05/23/2011; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List */ #ifndef _MACH_ANOMALY_H_ @@ -28,26 +27,148 @@ #define ANOMALY_05000119 (1) /* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ #define ANOMALY_05000122 (1) -/* Data Corruption with Cached External Memory and Non-Cached On-Chip L2 Memory */ -#define ANOMALY_05000220 (1) +/* Data Corruption/Core Hang with L2/L3 Configured in Writeback Cache Mode */ +#define ANOMALY_05000220 (__SILICON_REVISION__ < 4) /* False Hardware Error from an Access in the Shadow of a Conditional Branch */ #define ANOMALY_05000245 (1) /* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */ #define ANOMALY_05000265 (1) /* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */ #define ANOMALY_05000272 (1) -/* False Hardware Error Exception when ISR Context Is Not Restored */ +/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */ +#define ANOMALY_05000310 (1) +/* FIFO Boot Mode Not Functional */ +#define ANOMALY_05000325 (__SILICON_REVISION__ < 2) +/* bfrom_SysControl() Firmware Function Performs Improper System Reset */ +/* + * Note: anomaly sheet says this is fixed with bf54x-0.2+, but testing + * shows that the fix itself does not cover all cases. + */ +#define ANOMALY_05000353 (1) +/* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */ +#define ANOMALY_05000357 (1) +/* External Memory Read Access Hangs Core With PLL Bypass */ +#define ANOMALY_05000360 (1) +/* DMAs that Go Urgent during Tight Core Writes to External Memory Are Blocked */ +#define ANOMALY_05000365 (1) +/* Addressing Conflict between Boot ROM and Asynchronous Memory */ +#define ANOMALY_05000369 (1) +/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ +#define ANOMALY_05000371 (__SILICON_REVISION__ < 2) +/* Security/Authentication Speedpath Causes Authentication To Fail To Initiate */ +#define ANOMALY_05000378 (__SILICON_REVISION__ < 2) +/* 16-Bit NAND FLASH Boot Mode Is Not Functional */ +#define ANOMALY_05000379 (1) +/* Lockbox SESR Disallows Certain User Interrupts */ +#define ANOMALY_05000404 (__SILICON_REVISION__ < 2) +/* Lockbox SESR Firmware Does Not Save/Restore Full Context */ +#define ANOMALY_05000405 (1) +/* Lockbox SESR Argument Checking Does Not Check L2 Memory Protection Range */ +#define ANOMALY_05000406 (__SILICON_REVISION__ < 2) +/* Lockbox SESR Firmware Arguments Are Not Retained After First Initialization */ +#define ANOMALY_05000407 (__SILICON_REVISION__ < 2) +/* Lockbox Firmware Memory Cleanup Routine Does not Clear Registers */ +#define ANOMALY_05000408 (1) +/* Lockbox firmware leaves MDMA0 channel enabled */ +#define ANOMALY_05000409 (__SILICON_REVISION__ < 2) +/* bfrom_SysControl() Firmware Function Cannot be Used to Enter Power Saving Modes */ +#define ANOMALY_05000411 (__SILICON_REVISION__ < 2) +/* NAND Boot Mode Not Compatible With Some NAND Flash Devices */ +#define ANOMALY_05000413 (__SILICON_REVISION__ < 2) +/* OTP_CHECK_FOR_PREV_WRITE Bit is Not Functional in bfrom_OtpWrite() API */ +#define ANOMALY_05000414 (__SILICON_REVISION__ < 2) +/* Speculative Fetches Can Cause Undesired External FIFO Operations */ +#define ANOMALY_05000416 (1) +/* Multichannel SPORT Channel Misalignment Under Specific Configuration */ +#define ANOMALY_05000425 (__SILICON_REVISION__ < 4) +/* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */ +#define ANOMALY_05000426 (1) +/* CORE_EPPI_PRIO bit and SYS_EPPI_PRIO bit in the HMDMA1_CONTROL register are not functional */ +#define ANOMALY_05000427 (__SILICON_REVISION__ < 2) +/* WB_EDGE Bit in NFC_IRQSTAT Incorrectly Reflects Buffer Status Instead of IRQ Status */ +#define ANOMALY_05000429 (__SILICON_REVISION__ < 2) +/* Software System Reset Corrupts PLL_LOCKCNT Register */ +#define ANOMALY_05000430 (__SILICON_REVISION__ >= 2) +/* Incorrect Use of Stack in Lockbox Firmware During Authentication */ +#define ANOMALY_05000431 (__SILICON_REVISION__ < 3) +/* SW Breakpoints Ignored Upon Return From Lockbox Authentication */ +#define ANOMALY_05000434 (1) +/* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ +#define ANOMALY_05000443 (1) +/* CDMAPRIO and L2DMAPRIO Bits in the SYSCR Register Are Not Functional */ +#define ANOMALY_05000446 (1) +/* UART IrDA Receiver Fails on Extended Bit Pulses */ +#define ANOMALY_05000447 (1) +/* DDR Clock Duty Cycle Spec Violation (tCH, tCL) */ +#define ANOMALY_05000448 (__SILICON_REVISION__ == 1) +/* Reduced Timing Margins on DDR Output Setup and Hold (tDS and tDH) */ +#define ANOMALY_05000449 (__SILICON_REVISION__ == 1) +/* USB DMA Short Packet Data Corruption */ +#define ANOMALY_05000450 (1) +/* USB Receive Interrupt Is Not Generated in DMA Mode 1 */ +#define ANOMALY_05000456 (1) +/* Host DMA Port Responds to Certain Bus Activity Without HOST_CE Assertion */ +#define ANOMALY_05000457 (1) +/* USB DMA Mode 1 Failure When Multiple USB DMA Channels Are Concurrently Enabled */ +#define ANOMALY_05000460 (__SILICON_REVISION__ < 4) +/* False Hardware Error when RETI Points to Invalid Memory */ +#define ANOMALY_05000461 (1) +/* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */ +#define ANOMALY_05000462 (__SILICON_REVISION__ < 4) +/* USB DMA RX Data Corruption */ +#define ANOMALY_05000463 (__SILICON_REVISION__ < 4) +/* USB TX DMA Hang */ +#define ANOMALY_05000464 (__SILICON_REVISION__ < 4) +/* USB Rx DMA Hang */ +#define ANOMALY_05000465 (1) +/* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */ +#define ANOMALY_05000466 (__SILICON_REVISION__ < 4) +/* Possible USB RX Data Corruption When Control & Data EP FIFOs are Accessed via the Core */ +#define ANOMALY_05000467 (__SILICON_REVISION__ < 4) +/* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */ +#define ANOMALY_05000473 (1) +/* Access to DDR SDRAM Causes System Hang with Certain PLL Settings */ +#define ANOMALY_05000474 (__SILICON_REVISION__ < 4) +/* TESTSET Instruction Cannot Be Interrupted */ +#define ANOMALY_05000477 (1) +/* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */ +#define ANOMALY_05000481 (1) +/* Possible USB Data Corruption When Multiple Endpoints Are Accessed by the Core */ +#define ANOMALY_05000483 (1) +/* DDR Trim May Not Be Performed for Certain VLEV Values in OTP Page PBS00L */ +#define ANOMALY_05000484 (__SILICON_REVISION__ < 3) +/* PLL_CTL Change Using bfrom_SysControl() Can Result in Processor Overclocking */ +#define ANOMALY_05000485 (__SILICON_REVISION__ > 1 && __SILICON_REVISION__ < 4) +/* PLL May Latch Incorrect Values Coming Out of Reset */ +#define ANOMALY_05000489 (1) +/* SPI Master Boot Can Fail Under Certain Conditions */ +#define ANOMALY_05000490 (1) +/* Instruction Memory Stalls Can Cause IFLUSH to Fail */ +#define ANOMALY_05000491 (1) +/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */ +#define ANOMALY_05000494 (1) +/* CNT_COMMAND Functionality Depends on CNT_IMASK Configuration */ +#define ANOMALY_05000498 (1) +/* Nand Flash Controller Hangs When the AMC Requests the Async Pins During the last 16 Bytes of a Page Write Operation. */ +#define ANOMALY_05000500 (1) +/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */ +#define ANOMALY_05000501 (1) +/* Async Memory Writes May Be Skipped When Using Odd Clock Ratios */ +#define ANOMALY_05000502 (1) + +/* + * These anomalies have been "phased" out of analog.com anomaly sheets and are + * here to show running on older silicon just isn't feasible. + */ + +/* False Hardware Error when ISR Context Is Not Restored */ #define ANOMALY_05000281 (__SILICON_REVISION__ < 1) /* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */ #define ANOMALY_05000304 (__SILICON_REVISION__ < 1) -/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */ -#define ANOMALY_05000310 (1) /* Errors when SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */ #define ANOMALY_05000312 (__SILICON_REVISION__ < 1) /* TWI Slave Boot Mode Is Not Functional */ #define ANOMALY_05000324 (__SILICON_REVISION__ < 1) -/* FIFO Boot Mode Not Functional */ -#define ANOMALY_05000325 (__SILICON_REVISION__ < 2) /* Data Lost When Core and DMA Accesses Are Made to the USB FIFO Simultaneously */ #define ANOMALY_05000327 (__SILICON_REVISION__ < 1) /* Incorrect Access of OTP_STATUS During otp_write() Function */ @@ -80,36 +201,18 @@ #define ANOMALY_05000349 (__SILICON_REVISION__ < 1) /* PLL Status Register Is Inaccurate */ #define ANOMALY_05000351 (__SILICON_REVISION__ < 1) -/* bfrom_SysControl() Firmware Function Performs Improper System Reset */ -#define ANOMALY_05000353 (__SILICON_REVISION__ < 2) /* Regulator Programming Blocked when Hibernate Wakeup Source Remains Active */ #define ANOMALY_05000355 (__SILICON_REVISION__ < 1) /* System Stalled During A Core Access To AMC While A Core Access To NFC FIFO Is Required */ #define ANOMALY_05000356 (__SILICON_REVISION__ < 1) -/* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */ -#define ANOMALY_05000357 (1) -/* External Memory Read Access Hangs Core With PLL Bypass */ -#define ANOMALY_05000360 (1) -/* DMAs that Go Urgent during Tight Core Writes to External Memory Are Blocked */ -#define ANOMALY_05000365 (1) /* WURESET Bit In SYSCR Register Does Not Properly Indicate Hibernate Wake-Up */ #define ANOMALY_05000367 (__SILICON_REVISION__ < 1) -/* Addressing Conflict between Boot ROM and Asynchronous Memory */ -#define ANOMALY_05000369 (1) /* Default PLL MSEL and SSEL Settings Can Cause 400MHz Product To Violate Specifications */ #define ANOMALY_05000370 (__SILICON_REVISION__ < 1) -/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ -#define ANOMALY_05000371 (__SILICON_REVISION__ < 2) /* USB DP/DM Data Pins May Lose State When Entering Hibernate */ #define ANOMALY_05000372 (__SILICON_REVISION__ < 1) -/* Security/Authentication Speedpath Causes Authentication To Fail To Initiate */ -#define ANOMALY_05000378 (__SILICON_REVISION__ < 2) -/* 16-Bit NAND FLASH Boot Mode Is Not Functional */ -#define ANOMALY_05000379 (1) /* 8-Bit NAND Flash Boot Mode Not Functional */ #define ANOMALY_05000382 (__SILICON_REVISION__ < 1) -/* Some ATAPI Modes Are Not Functional */ -#define ANOMALY_05000383 (1) /* Boot from OTP Memory Not Functional */ #define ANOMALY_05000385 (__SILICON_REVISION__ < 1) /* bfrom_SysControl() Firmware Routine Not Functional */ @@ -136,84 +239,10 @@ #define ANOMALY_05000396 (__SILICON_REVISION__ < 1) /* BK_ONES, BK_ZEROS, and BK_DATECODE Constants Not Functional */ #define ANOMALY_05000397 (__SILICON_REVISION__ < 1) -/* Lockbox SESR Disallows Certain User Interrupts */ -#define ANOMALY_05000404 (__SILICON_REVISION__ < 2) -/* Lockbox SESR Firmware Does Not Save/Restore Full Context */ -#define ANOMALY_05000405 (1) -/* Lockbox SESR Argument Checking Does Not Check L2 Memory Protection Range */ -#define ANOMALY_05000406 (__SILICON_REVISION__ < 2) -/* Lockbox SESR Firmware Arguments Are Not Retained After First Initialization */ -#define ANOMALY_05000407 (__SILICON_REVISION__ < 2) -/* Lockbox Firmware Memory Cleanup Routine Does not Clear Registers */ -#define ANOMALY_05000408 (1) -/* Lockbox firmware leaves MDMA0 channel enabled */ -#define ANOMALY_05000409 (__SILICON_REVISION__ < 2) -/* bfrom_SysControl() Firmware Function Cannot be Used to Enter Power Saving Modes */ -#define ANOMALY_05000411 (__SILICON_REVISION__ < 2) -/* NAND Boot Mode Not Compatible With Some NAND Flash Devices */ -#define ANOMALY_05000413 (__SILICON_REVISION__ < 2) -/* OTP_CHECK_FOR_PREV_WRITE Bit is Not Functional in bfrom_OtpWrite() API */ -#define ANOMALY_05000414 (__SILICON_REVISION__ < 2) -/* Speculative Fetches Can Cause Undesired External FIFO Operations */ -#define ANOMALY_05000416 (1) -/* Multichannel SPORT Channel Misalignment Under Specific Configuration */ -#define ANOMALY_05000425 (1) -/* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */ -#define ANOMALY_05000426 (1) -/* CORE_EPPI_PRIO bit and SYS_EPPI_PRIO bit in the HMDMA1_CONTROL register are not functional */ -#define ANOMALY_05000427 (__SILICON_REVISION__ < 2) -/* WB_EDGE Bit in NFC_IRQSTAT Incorrectly Reflects Buffer Status Instead of IRQ Status */ -#define ANOMALY_05000429 (__SILICON_REVISION__ < 2) -/* Software System Reset Corrupts PLL_LOCKCNT Register */ -#define ANOMALY_05000430 (__SILICON_REVISION__ >= 2) -/* Incorrect Use of Stack in Lockbox Firmware During Authentication */ -#define ANOMALY_05000431 (__SILICON_REVISION__ < 3) -/* SW Breakpoints Ignored Upon Return From Lockbox Authentication */ -#define ANOMALY_05000434 (1) /* OTP Write Accesses Not Supported */ #define ANOMALY_05000442 (__SILICON_REVISION__ < 1) -/* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ -#define ANOMALY_05000443 (1) -/* CDMAPRIO and L2DMAPRIO Bits in the SYSCR Register Are Not Functional */ -#define ANOMALY_05000446 (1) -/* UART IrDA Receiver Fails on Extended Bit Pulses */ -#define ANOMALY_05000447 (1) -/* DDR Clock Duty Cycle Spec Violation (tCH, tCL) */ -#define ANOMALY_05000448 (__SILICON_REVISION__ == 1) -/* Reduced Timing Margins on DDR Output Setup and Hold (tDS and tDH) */ -#define ANOMALY_05000449 (__SILICON_REVISION__ == 1) -/* USB DMA Mode 1 Short Packet Data Corruption */ -#define ANOMALY_05000450 (1) /* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */ #define ANOMALY_05000452 (__SILICON_REVISION__ < 1) -/* USB Receive Interrupt Is Not Generated in DMA Mode 1 */ -#define ANOMALY_05000456 (1) -/* Host DMA Port Responds to Certain Bus Activity Without HOST_CE Assertion */ -#define ANOMALY_05000457 (1) -/* USB DMA Mode 1 Failure When Multiple USB DMA Channels Are Concurrently Enabled */ -#define ANOMALY_05000460 (1) -/* False Hardware Error when RETI Points to Invalid Memory */ -#define ANOMALY_05000461 (1) -/* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */ -#define ANOMALY_05000462 (1) -/* USB DMA RX Data Corruption */ -#define ANOMALY_05000463 (1) -/* USB TX DMA Hang */ -#define ANOMALY_05000464 (1) -/* USB Rx DMA hang */ -#define ANOMALY_05000465 (1) -/* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */ -#define ANOMALY_05000466 (1) -/* Possible RX data corruption when control & data EP FIFOs are accessed via the core */ -#define ANOMALY_05000467 (1) -/* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */ -#define ANOMALY_05000473 (1) -/* Access to DDR-SDRAM causes system hang under certain PLL/VR settings */ -#define ANOMALY_05000474 (1) -/* Core Hang With L2/L3 Configured in Writeback Cache Mode */ -#define ANOMALY_05000475 (1) -/* TESTSET Instruction Cannot Be Interrupted */ -#define ANOMALY_05000477 (1) /* Anomalies that don't exist on this proc */ #define ANOMALY_05000099 (0) @@ -229,6 +258,7 @@ #define ANOMALY_05000198 (0) #define ANOMALY_05000202 (0) #define ANOMALY_05000215 (0) +#define ANOMALY_05000219 (0) #define ANOMALY_05000227 (0) #define ANOMALY_05000230 (0) #define ANOMALY_05000231 (0) @@ -263,5 +293,9 @@ #define ANOMALY_05000412 (0) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) +#define ANOMALY_05000440 (0) +#define ANOMALY_05000475 (0) +#define ANOMALY_05000480 (0) +#define ANOMALY_16000030 (0) #endif diff --git a/arch/blackfin/mach-bf548/include/mach/bfin_serial.h b/arch/blackfin/mach-bf548/include/mach/bfin_serial.h new file mode 100644 index 00000000000..a77109f9972 --- /dev/null +++ b/arch/blackfin/mach-bf548/include/mach/bfin_serial.h @@ -0,0 +1,16 @@ +/* + * mach/bfin_serial.h - Blackfin UART/Serial definitions + * + * Copyright 2006-2010 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __BFIN_MACH_SERIAL_H__ +#define __BFIN_MACH_SERIAL_H__ + +#define BFIN_UART_NR_PORTS 4 + +#define BFIN_UART_BF54X_STYLE + +#endif diff --git a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h deleted file mode 100644 index dd44aa75fe7..00000000000 --- a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h +++ /dev/null @@ -1,150 +0,0 @@ -/* - * Copyright 2007-2009 Analog Devices Inc. - * - * Licensed under the GPL-2 or later. - */ - -#include <linux/serial.h> -#include <asm/dma.h> -#include <asm/portmux.h> - -#define UART_GET_CHAR(uart) bfin_read16(((uart)->port.membase + OFFSET_RBR)) -#define UART_GET_DLL(uart) bfin_read16(((uart)->port.membase + OFFSET_DLL)) -#define UART_GET_DLH(uart) bfin_read16(((uart)->port.membase + OFFSET_DLH)) -#define UART_GET_IER(uart) bfin_read16(((uart)->port.membase + OFFSET_IER_SET)) -#define UART_GET_LCR(uart) bfin_read16(((uart)->port.membase + OFFSET_LCR)) -#define UART_GET_LSR(uart) bfin_read16(((uart)->port.membase + OFFSET_LSR)) -#define UART_GET_GCTL(uart) bfin_read16(((uart)->port.membase + OFFSET_GCTL)) -#define UART_GET_MSR(uart) bfin_read16(((uart)->port.membase + OFFSET_MSR)) -#define UART_GET_MCR(uart) bfin_read16(((uart)->port.membase + OFFSET_MCR)) - -#define UART_PUT_CHAR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_THR),v) -#define UART_PUT_DLL(uart,v) bfin_write16(((uart)->port.membase + OFFSET_DLL),v) -#define UART_SET_IER(uart,v) bfin_write16(((uart)->port.membase + OFFSET_IER_SET),v) -#define UART_CLEAR_IER(uart,v) bfin_write16(((uart)->port.membase + OFFSET_IER_CLEAR),v) -#define UART_PUT_DLH(uart,v) bfin_write16(((uart)->port.membase + OFFSET_DLH),v) -#define UART_PUT_LSR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_LSR),v) -#define UART_PUT_LCR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_LCR),v) -#define UART_CLEAR_LSR(uart) bfin_write16(((uart)->port.membase + OFFSET_LSR), -1) -#define UART_PUT_GCTL(uart,v) bfin_write16(((uart)->port.membase + OFFSET_GCTL),v) -#define UART_PUT_MCR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_MCR),v) -#define UART_CLEAR_SCTS(uart) bfin_write16(((uart)->port.membase + OFFSET_MSR),SCTS) - -#define UART_SET_DLAB(uart) /* MMRs not muxed on BF54x */ -#define UART_CLEAR_DLAB(uart) /* MMRs not muxed on BF54x */ - -#define UART_GET_CTS(x) (UART_GET_MSR(x) & CTS) -#define UART_DISABLE_RTS(x) UART_PUT_MCR(x, UART_GET_MCR(x) & ~(ARTS|MRTS)) -#define UART_ENABLE_RTS(x) UART_PUT_MCR(x, UART_GET_MCR(x) | MRTS | ARTS) -#define UART_ENABLE_INTS(x, v) UART_SET_IER(x, v) -#define UART_DISABLE_INTS(x) UART_CLEAR_IER(x, 0xF) - -#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) || \ - defined(CONFIG_BFIN_UART2_CTSRTS) || defined(CONFIG_BFIN_UART3_CTSRTS) -# define CONFIG_SERIAL_BFIN_HARD_CTSRTS -#endif - -#define BFIN_UART_TX_FIFO_SIZE 2 - -/* - * The pin configuration is different from schematic - */ -struct bfin_serial_port { - struct uart_port port; - unsigned int old_status; - int status_irq; -#ifdef CONFIG_SERIAL_BFIN_DMA - int tx_done; - int tx_count; - struct circ_buf rx_dma_buf; - struct timer_list rx_dma_timer; - int rx_dma_nrows; - unsigned int tx_dma_channel; - unsigned int rx_dma_channel; - struct work_struct tx_dma_workqueue; -#endif -#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS - int scts; - int cts_pin; - int rts_pin; -#endif -}; - -struct bfin_serial_res { - unsigned long uart_base_addr; - int uart_irq; - int uart_status_irq; -#ifdef CONFIG_SERIAL_BFIN_DMA - unsigned int uart_tx_dma_channel; - unsigned int uart_rx_dma_channel; -#endif -#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS - int uart_cts_pin; - int uart_rts_pin; -#endif -}; - -struct bfin_serial_res bfin_serial_resource[] = { -#ifdef CONFIG_SERIAL_BFIN_UART0 - { - 0xFFC00400, - IRQ_UART0_RX, - IRQ_UART0_ERROR, -#ifdef CONFIG_SERIAL_BFIN_DMA - CH_UART0_TX, - CH_UART0_RX, -#endif -#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS - 0, - 0, -#endif - }, -#endif -#ifdef CONFIG_SERIAL_BFIN_UART1 - { - 0xFFC02000, - IRQ_UART1_RX, - IRQ_UART1_ERROR, -#ifdef CONFIG_SERIAL_BFIN_DMA - CH_UART1_TX, - CH_UART1_RX, -#endif -#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS - GPIO_PE10, - GPIO_PE9, -#endif - }, -#endif -#ifdef CONFIG_SERIAL_BFIN_UART2 - { - 0xFFC02100, - IRQ_UART2_RX, - IRQ_UART2_ERROR, -#ifdef CONFIG_SERIAL_BFIN_DMA - CH_UART2_TX, - CH_UART2_RX, -#endif -#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS - 0, - 0, -#endif - }, -#endif -#ifdef CONFIG_SERIAL_BFIN_UART3 - { - 0xFFC03100, - IRQ_UART3_RX, - IRQ_UART3_ERROR, -#ifdef CONFIG_SERIAL_BFIN_DMA - CH_UART3_TX, - CH_UART3_RX, -#endif -#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS - GPIO_PB3, - GPIO_PB2, -#endif - }, -#endif -}; - -#define DRIVER_NAME "bfin-uart" diff --git a/arch/blackfin/mach-bf548/include/mach/blackfin.h b/arch/blackfin/mach-bf548/include/mach/blackfin.h index 5684030ccc2..72da721a77f 100644 --- a/arch/blackfin/mach-bf548/include/mach/blackfin.h +++ b/arch/blackfin/mach-bf548/include/mach/blackfin.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2009 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -10,58 +10,40 @@ #include "bf548.h" #include "anomaly.h" +#include <asm/def_LPBlackfin.h> #ifdef CONFIG_BF542 -#include "defBF542.h" +# include "defBF542.h" #endif - #ifdef CONFIG_BF544 -#include "defBF544.h" +# include "defBF544.h" #endif - #ifdef CONFIG_BF547 -#include "defBF547.h" +# include "defBF547.h" #endif - #ifdef CONFIG_BF548 -#include "defBF548.h" +# include "defBF548.h" #endif - #ifdef CONFIG_BF549 -#include "defBF549.h" -#endif - -#if !defined(__ASSEMBLY__) -#ifdef CONFIG_BF542 -#include "cdefBF542.h" +# include "defBF549.h" +#endif + +#ifndef __ASSEMBLY__ +# include <asm/cdef_LPBlackfin.h> +# ifdef CONFIG_BF542 +# include "cdefBF542.h" +# endif +# ifdef CONFIG_BF544 +# include "cdefBF544.h" +# endif +# ifdef CONFIG_BF547 +# include "cdefBF547.h" +# endif +# ifdef CONFIG_BF548 +# include "cdefBF548.h" +# endif +# ifdef CONFIG_BF549 +# include "cdefBF549.h" +# endif #endif -#ifdef CONFIG_BF544 -#include "cdefBF544.h" -#endif -#ifdef CONFIG_BF547 -#include "cdefBF547.h" -#endif -#ifdef CONFIG_BF548 -#include "cdefBF548.h" -#endif -#ifdef CONFIG_BF549 -#include "cdefBF549.h" -#endif - -#endif - -#define BFIN_UART_NR_PORTS 4 - -#define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */ -#define OFFSET_DLH 0x04 /* Divisor Latch (High-Byte) */ -#define OFFSET_GCTL 0x08 /* Global Control Register */ -#define OFFSET_LCR 0x0C /* Line Control Register */ -#define OFFSET_MCR 0x10 /* Modem Control Register */ -#define OFFSET_LSR 0x14 /* Line Status Register */ -#define OFFSET_MSR 0x18 /* Modem Status Register */ -#define OFFSET_SCR 0x1C /* SCR Scratch Register */ -#define OFFSET_IER_SET 0x20 /* Set Interrupt Enable Register */ -#define OFFSET_IER_CLEAR 0x24 /* Clear Interrupt Enable Register */ -#define OFFSET_THR 0x28 /* Transmit Holding register */ -#define OFFSET_RBR 0x2C /* Receive Buffer register */ #endif diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF542.h b/arch/blackfin/mach-bf548/include/mach/cdefBF542.h index 42f4a946954..d09c19cd1b7 100644 --- a/arch/blackfin/mach-bf548/include/mach/cdefBF542.h +++ b/arch/blackfin/mach-bf548/include/mach/cdefBF542.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -7,14 +7,6 @@ #ifndef _CDEF_BF542_H #define _CDEF_BF542_H -/* include all Core registers and bit definitions */ -#include "defBF542.h" - -/* include core sbfin_read_()ecific register pointer definitions */ -#include <asm/cdef_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF542 */ - /* include cdefBF54x_base.h for the set of #defines that are common to all ADSP-BF54x bfin_read_()rocessors */ #include "cdefBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF544.h b/arch/blackfin/mach-bf548/include/mach/cdefBF544.h index 2207799575f..33ec8102ced 100644 --- a/arch/blackfin/mach-bf548/include/mach/cdefBF544.h +++ b/arch/blackfin/mach-bf548/include/mach/cdefBF544.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -7,14 +7,6 @@ #ifndef _CDEF_BF544_H #define _CDEF_BF544_H -/* include all Core registers and bit definitions */ -#include "defBF544.h" - -/* include core sbfin_read_()ecific register pointer definitions */ -#include <asm/cdef_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF544 */ - /* include cdefBF54x_base.h for the set of #defines that are common to all ADSP-BF54x bfin_read_()rocessors */ #include "cdefBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF547.h b/arch/blackfin/mach-bf548/include/mach/cdefBF547.h index bc650e6ea48..bcb9726dea5 100644 --- a/arch/blackfin/mach-bf548/include/mach/cdefBF547.h +++ b/arch/blackfin/mach-bf548/include/mach/cdefBF547.h @@ -1,5 +1,5 @@ /* - * Copyright 2008 Analog Devices Inc. + * Copyright 2008-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -7,14 +7,6 @@ #ifndef _CDEF_BF547_H #define _CDEF_BF547_H -/* include all Core registers and bit definitions */ -#include "defBF547.h" - -/* include core sbfin_read_()ecific register pointer definitions */ -#include <asm/cdef_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF547 */ - /* include cdefBF54x_base.h for the set of #defines that are common to all ADSP-BF54x bfin_read_()rocessors */ #include "cdefBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF548.h b/arch/blackfin/mach-bf548/include/mach/cdefBF548.h index 3523e08f796..bae67a65633 100644 --- a/arch/blackfin/mach-bf548/include/mach/cdefBF548.h +++ b/arch/blackfin/mach-bf548/include/mach/cdefBF548.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -7,14 +7,6 @@ #ifndef _CDEF_BF548_H #define _CDEF_BF548_H -/* include all Core registers and bit definitions */ -#include "defBF548.h" - -/* include core sbfin_read_()ecific register pointer definitions */ -#include <asm/cdef_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF548 */ - /* include cdefBF54x_base.h for the set of #defines that are common to all ADSP-BF54x bfin_read_()rocessors */ #include "cdefBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF549.h b/arch/blackfin/mach-bf548/include/mach/cdefBF549.h index 80201ed41f8..002136ad5a4 100644 --- a/arch/blackfin/mach-bf548/include/mach/cdefBF549.h +++ b/arch/blackfin/mach-bf548/include/mach/cdefBF549.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -7,14 +7,6 @@ #ifndef _CDEF_BF549_H #define _CDEF_BF549_H -/* include all Core registers and bit definitions */ -#include "defBF549.h" - -/* include core sbfin_read_()ecific register pointer definitions */ -#include <asm/cdef_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF549 */ - /* include cdefBF54x_base.h for the set of #defines that are common to all ADSP-BF54x bfin_read_()rocessors */ #include "cdefBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h b/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h index 32f71e6a7c1..50c89c8052f 100644 --- a/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h +++ b/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h @@ -1,5 +1,5 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -7,10 +7,6 @@ #ifndef _CDEF_BF54X_H #define _CDEF_BF54X_H -#include <asm/blackfin.h> - -#include "defBF54x_base.h" - /* ************************************************************** */ /* SYSTEM & MMR ADDRESS DEFINITIONS COMMON TO ALL ADSP-BF54x */ /* ************************************************************** */ @@ -40,6 +36,8 @@ /* SIC Registers */ +#define bfin_read_SIC_RVECT() bfin_read32(SIC_RVECT) +#define bfin_write_SIC_RVECT(val) bfin_write32(SIC_RVECT, val) #define bfin_read_SIC_IMASK0() bfin_read32(SIC_IMASK0) #define bfin_write_SIC_IMASK0(val) bfin_write32(SIC_IMASK0, val) #define bfin_read_SIC_IMASK1() bfin_read32(SIC_IMASK1) @@ -301,10 +299,10 @@ /* DMAC0 Registers */ -#define bfin_read_DMAC0_TCPER() bfin_read16(DMAC0_TCPER) -#define bfin_write_DMAC0_TCPER(val) bfin_write16(DMAC0_TCPER, val) -#define bfin_read_DMAC0_TCCNT() bfin_read16(DMAC0_TCCNT) -#define bfin_write_DMAC0_TCCNT(val) bfin_write16(DMAC0_TCCNT, val) +#define bfin_read_DMAC0_TC_PER() bfin_read16(DMAC0_TC_PER) +#define bfin_write_DMAC0_TC_PER(val) bfin_write16(DMAC0_TC_PER, val) +#define bfin_read_DMAC0_TC_CNT() bfin_read16(DMAC0_TC_CNT) +#define bfin_write_DMAC0_TC_CNT(val) bfin_write16(DMAC0_TC_CNT, val) /* DMA Channel 0 Registers */ @@ -1155,10 +1153,10 @@ /* DMAC1 Registers */ -#define bfin_read_DMAC1_TCPER() bfin_read16(DMAC1_TCPER) -#define bfin_write_DMAC1_TCPER(val) bfin_write16(DMAC1_TCPER, val) -#define bfin_read_DMAC1_TCCNT() bfin_read16(DMAC1_TCCNT) -#define bfin_write_DMAC1_TCCNT(val) bfin_write16(DMAC1_TCCNT, val) +#define bfin_read_DMAC1_TC_PER() bfin_read16(DMAC1_TC_PER) +#define bfin_write_DMAC1_TC_PER(val) bfin_write16(DMAC1_TC_PER, val) +#define bfin_read_DMAC1_TC_CNT() bfin_read16(DMAC1_TC_CNT) +#define bfin_write_DMAC1_TC_CNT(val) bfin_write16(DMAC1_TC_CNT, val) /* DMA Channel 12 Registers */ @@ -2631,78 +2629,5 @@ /* Handshake MDMA is not defined in the shared file because it is not available on the ADSP-BF542 bfin_read_()rocessor */ -/* legacy definitions */ -#define bfin_read_EBIU_AMCBCTL0 bfin_read_EBIU_AMBCTL0 -#define bfin_write_EBIU_AMCBCTL0 bfin_write_EBIU_AMBCTL0 -#define bfin_read_EBIU_AMCBCTL1 bfin_read_EBIU_AMBCTL1 -#define bfin_write_EBIU_AMCBCTL1 bfin_write_EBIU_AMBCTL1 -#define bfin_read_PINT0_IRQ bfin_read_PINT0_REQUEST -#define bfin_write_PINT0_IRQ bfin_write_PINT0_REQUEST -#define bfin_read_PINT1_IRQ bfin_read_PINT1_REQUEST -#define bfin_write_PINT1_IRQ bfin_write_PINT1_REQUEST -#define bfin_read_PINT2_IRQ bfin_read_PINT2_REQUEST -#define bfin_write_PINT2_IRQ bfin_write_PINT2_REQUEST -#define bfin_read_PINT3_IRQ bfin_read_PINT3_REQUEST -#define bfin_write_PINT3_IRQ bfin_write_PINT3_REQUEST - -/* These need to be last due to the cdef/linux inter-dependencies */ -#include <asm/irq.h> - -/* Writing to PLL_CTL initiates a PLL relock sequence. */ -static __inline__ void bfin_write_PLL_CTL(unsigned int val) -{ - unsigned long flags, iwr0, iwr1, iwr2; - - if (val == bfin_read_PLL_CTL()) - return; - - local_irq_save_hw(flags); - /* Enable the PLL Wakeup bit in SIC IWR */ - iwr0 = bfin_read32(SIC_IWR0); - iwr1 = bfin_read32(SIC_IWR1); - iwr2 = bfin_read32(SIC_IWR2); - /* Only allow PPL Wakeup) */ - bfin_write32(SIC_IWR0, IWR_ENABLE(0)); - bfin_write32(SIC_IWR1, 0); - bfin_write32(SIC_IWR2, 0); - - bfin_write16(PLL_CTL, val); - SSYNC(); - asm("IDLE;"); - - bfin_write32(SIC_IWR0, iwr0); - bfin_write32(SIC_IWR1, iwr1); - bfin_write32(SIC_IWR2, iwr2); - local_irq_restore_hw(flags); -} - -/* Writing to VR_CTL initiates a PLL relock sequence. */ -static __inline__ void bfin_write_VR_CTL(unsigned int val) -{ - unsigned long flags, iwr0, iwr1, iwr2; - - if (val == bfin_read_VR_CTL()) - return; - - local_irq_save_hw(flags); - /* Enable the PLL Wakeup bit in SIC IWR */ - iwr0 = bfin_read32(SIC_IWR0); - iwr1 = bfin_read32(SIC_IWR1); - iwr2 = bfin_read32(SIC_IWR2); - /* Only allow PPL Wakeup) */ - bfin_write32(SIC_IWR0, IWR_ENABLE(0)); - bfin_write32(SIC_IWR1, 0); - bfin_write32(SIC_IWR2, 0); - - bfin_write16(VR_CTL, val); - SSYNC(); - asm("IDLE;"); - - bfin_write32(SIC_IWR0, iwr0); - bfin_write32(SIC_IWR1, iwr1); - bfin_write32(SIC_IWR2, iwr2); - local_irq_restore_hw(flags); -} - #endif /* _CDEF_BF54X_H */ diff --git a/arch/blackfin/mach-bf548/include/mach/defBF542.h b/arch/blackfin/mach-bf548/include/mach/defBF542.h index d3bc6d1df54..51161575a16 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF542.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF542.h @@ -1,17 +1,12 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * - * Licensed under the ADI BSD license or the GPL-2 (or later) + * Licensed under the Clear BSD license or the GPL-2 (or later) */ #ifndef _DEF_BF542_H #define _DEF_BF542_H -/* Include all Core registers and bit definitions */ -#include <asm/def_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF542 */ - /* Include defBF54x_base.h for the set of #defines that are common to all ADSP-BF54x processors */ #include "defBF54x_base.h" @@ -366,136 +361,6 @@ #define KPAD_SOFTEVAL_E 0x2 /* Software Programmable Force Evaluate */ -/* Bit masks for SDH_COMMAND */ - -#define CMD_IDX 0x3f /* Command Index */ -#define CMD_RSP 0x40 /* Response */ -#define CMD_L_RSP 0x80 /* Long Response */ -#define CMD_INT_E 0x100 /* Command Interrupt */ -#define CMD_PEND_E 0x200 /* Command Pending */ -#define CMD_E 0x400 /* Command Enable */ - -/* Bit masks for SDH_PWR_CTL */ - -#define PWR_ON 0x3 /* Power On */ -#if 0 -#define TBD 0x3c /* TBD */ -#endif -#define SD_CMD_OD 0x40 /* Open Drain Output */ -#define ROD_CTL 0x80 /* Rod Control */ - -/* Bit masks for SDH_CLK_CTL */ - -#define CLKDIV 0xff /* MC_CLK Divisor */ -#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */ -#define PWR_SV_E 0x200 /* Power Save Enable */ -#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */ -#define WIDE_BUS 0x800 /* Wide Bus Mode Enable */ - -/* Bit masks for SDH_RESP_CMD */ - -#define RESP_CMD 0x3f /* Response Command */ - -/* Bit masks for SDH_DATA_CTL */ - -#define DTX_E 0x1 /* Data Transfer Enable */ -#define DTX_DIR 0x2 /* Data Transfer Direction */ -#define DTX_MODE 0x4 /* Data Transfer Mode */ -#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */ -#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */ - -/* Bit masks for SDH_STATUS */ - -#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */ -#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */ -#define CMD_TIME_OUT 0x4 /* CMD Time Out */ -#define DAT_TIME_OUT 0x8 /* Data Time Out */ -#define TX_UNDERRUN 0x10 /* Transmit Underrun */ -#define RX_OVERRUN 0x20 /* Receive Overrun */ -#define CMD_RESP_END 0x40 /* CMD Response End */ -#define CMD_SENT 0x80 /* CMD Sent */ -#define DAT_END 0x100 /* Data End */ -#define START_BIT_ERR 0x200 /* Start Bit Error */ -#define DAT_BLK_END 0x400 /* Data Block End */ -#define CMD_ACT 0x800 /* CMD Active */ -#define TX_ACT 0x1000 /* Transmit Active */ -#define RX_ACT 0x2000 /* Receive Active */ -#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */ -#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */ -#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */ -#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */ -#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */ -#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */ -#define TX_DAT_RDY 0x100000 /* Transmit Data Available */ -#define RX_FIFO_RDY 0x200000 /* Receive Data Available */ - -/* Bit masks for SDH_STATUS_CLR */ - -#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */ -#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */ -#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */ -#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */ -#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */ -#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */ -#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */ -#define CMD_SENT_STAT 0x80 /* CMD Sent Status */ -#define DAT_END_STAT 0x100 /* Data End Status */ -#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */ -#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */ - -/* Bit masks for SDH_MASK0 */ - -#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */ -#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */ -#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */ -#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */ -#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */ -#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */ -#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */ -#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */ -#define DAT_END_MASK 0x100 /* Data End Mask */ -#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */ -#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */ -#define CMD_ACT_MASK 0x800 /* CMD Active Mask */ -#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */ -#define RX_ACT_MASK 0x2000 /* Receive Active Mask */ -#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */ -#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */ -#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */ -#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */ -#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */ -#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */ -#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */ -#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */ - -/* Bit masks for SDH_FIFO_CNT */ - -#define FIFO_COUNT 0x7fff /* FIFO Count */ - -/* Bit masks for SDH_E_STATUS */ - -#define SDIO_INT_DET 0x2 /* SDIO Int Detected */ -#define SD_CARD_DET 0x10 /* SD Card Detect */ - -/* Bit masks for SDH_E_MASK */ - -#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */ -#define SCD_MSK 0x40 /* Mask Card Detect */ - -/* Bit masks for SDH_CFG */ - -#define CLKS_EN 0x1 /* Clocks Enable */ -#define SD4E 0x4 /* SDIO 4-Bit Enable */ -#define MWE 0x8 /* Moving Window Enable */ -#define SD_RST 0x10 /* SDMMC Reset */ -#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */ -#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */ -#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */ - -/* Bit masks for SDH_RD_WAIT_EN */ - -#define RWR 0x1 /* Read Wait Request */ - /* Bit masks for ATAPI_CONTROL */ #define PIO_START 0x1 /* Start PIO/Reg Op */ diff --git a/arch/blackfin/mach-bf548/include/mach/defBF544.h b/arch/blackfin/mach-bf548/include/mach/defBF544.h index f916c52a148..018ebfc27f5 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF544.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF544.h @@ -1,17 +1,12 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * - * Licensed under the ADI BSD license or the GPL-2 (or later) + * Licensed under the Clear BSD license or the GPL-2 (or later) */ #ifndef _DEF_BF544_H #define _DEF_BF544_H -/* Include all Core registers and bit definitions */ -#include <asm/def_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF544 */ - /* Include defBF54x_base.h for the set of #defines that are common to all ADSP-BF54x processors */ #include "defBF54x_base.h" @@ -60,15 +55,15 @@ #define TWI1_REGBASE 0xffc02200 #define TWI1_CLKDIV 0xffc02200 /* Clock Divider Register */ #define TWI1_CONTROL 0xffc02204 /* TWI Control Register */ -#define TWI1_SLAVE_CTRL 0xffc02208 /* TWI Slave Mode Control Register */ +#define TWI1_SLAVE_CTL 0xffc02208 /* TWI Slave Mode Control Register */ #define TWI1_SLAVE_STAT 0xffc0220c /* TWI Slave Mode Status Register */ #define TWI1_SLAVE_ADDR 0xffc02210 /* TWI Slave Mode Address Register */ -#define TWI1_MASTER_CTRL 0xffc02214 /* TWI Master Mode Control Register */ +#define TWI1_MASTER_CTL 0xffc02214 /* TWI Master Mode Control Register */ #define TWI1_MASTER_STAT 0xffc02218 /* TWI Master Mode Status Register */ #define TWI1_MASTER_ADDR 0xffc0221c /* TWI Master Mode Address Register */ #define TWI1_INT_STAT 0xffc02220 /* TWI Interrupt Status Register */ #define TWI1_INT_MASK 0xffc02224 /* TWI Interrupt Mask Register */ -#define TWI1_FIFO_CTRL 0xffc02228 /* TWI FIFO Control Register */ +#define TWI1_FIFO_CTL 0xffc02228 /* TWI FIFO Control Register */ #define TWI1_FIFO_STAT 0xffc0222c /* TWI FIFO Status Register */ #define TWI1_XMT_DATA8 0xffc02280 /* TWI FIFO Transmit Data Single Byte Register */ #define TWI1_XMT_DATA16 0xffc02284 /* TWI FIFO Transmit Data Double Byte Register */ @@ -606,36 +601,6 @@ #define GU_TRANS 0xff00 /* Transparent Color - G/U Component */ #define BV_TRANS 0xff0000 /* Transparent Color - B/V Component */ -/* Bit masks for HOST_CONTROL */ - -#define HOST_EN 0x1 /* Host Enable */ -#define HOST_END 0x2 /* Host Endianess */ -#define DATA_SIZE 0x4 /* Data Size */ -#define HOST_RST 0x8 /* Host Reset */ -#define HRDY_OVR 0x20 /* Host Ready Override */ -#define INT_MODE 0x40 /* Interrupt Mode */ -#define BT_EN 0x80 /* Bus Timeout Enable */ -#define EHW 0x100 /* Enable Host Write */ -#define EHR 0x200 /* Enable Host Read */ -#define BDR 0x400 /* Burst DMA Requests */ - -/* Bit masks for HOST_STATUS */ - -#define DMA_READY 0x1 /* DMA Ready */ -#define FIFOFULL 0x2 /* FIFO Full */ -#define FIFOEMPTY 0x4 /* FIFO Empty */ -#define DMA_COMPLETE 0x8 /* DMA Complete */ -#define HSHK 0x10 /* Host Handshake */ -#define HSTIMEOUT 0x20 /* Host Timeout */ -#define HIRQ 0x40 /* Host Interrupt Request */ -#define ALLOW_CNFG 0x80 /* Allow New Configuration */ -#define DMA_DIR 0x100 /* DMA Direction */ -#define BTE 0x200 /* Bus Timeout Enabled */ - -/* Bit masks for HOST_TIMEOUT */ - -#define COUNT_TIMEOUT 0x7ff /* Host Timeout count */ - /* Bit masks for TIMER_ENABLE1 */ #define TIMEN8 0x1 /* Timer 8 Enable */ @@ -662,22 +627,4 @@ /* Bit masks for EPPI0 are obtained from common base header for EPPIx (EPPI1 and EPPI2) */ -/* Bit masks for HMDMAx_CONTROL */ - -#define HMDMAEN 0x1 /* Handshake MDMA Enable */ -#define REP 0x2 /* Handshake MDMA Request Polarity */ -#define UTE 0x8 /* Urgency Threshold Enable */ -#define OIE 0x10 /* Overflow Interrupt Enable */ -#define BDIE 0x20 /* Block Done Interrupt Enable */ -#define MBDI 0x40 /* Mask Block Done Interrupt */ -#define DRQ 0x300 /* Handshake MDMA Request Type */ -#define RBC 0x1000 /* Force Reload of BCOUNT */ -#define PS 0x2000 /* Pin Status */ -#define OI 0x4000 /* Overflow Interrupt Generated */ -#define BDI 0x8000 /* Block Done Interrupt Generated */ - -/* ******************************************* */ -/* MULTI BIT MACRO ENUMERATIONS */ -/* ******************************************* */ - #endif /* _DEF_BF544_H */ diff --git a/arch/blackfin/mach-bf548/include/mach/defBF547.h b/arch/blackfin/mach-bf548/include/mach/defBF547.h index 72c343646b2..d55dcc0f532 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF547.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF547.h @@ -1,17 +1,12 @@ /* - * Copyright 2008 Analog Devices Inc. + * Copyright 2008-2010 Analog Devices Inc. * - * Licensed under the ADI BSD license or the GPL-2 (or later) + * Licensed under the Clear BSD license or the GPL-2 (or later) */ #ifndef _DEF_BF547_H #define _DEF_BF547_H -/* Include all Core registers and bit definitions */ -#include <asm/def_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF547 */ - /* Include defBF54x_base.h for the set of #defines that are common to all ADSP-BF54x processors */ #include "defBF54x_base.h" @@ -99,15 +94,15 @@ #define TWI1_REGBASE 0xffc02200 #define TWI1_CLKDIV 0xffc02200 /* Clock Divider Register */ #define TWI1_CONTROL 0xffc02204 /* TWI Control Register */ -#define TWI1_SLAVE_CTRL 0xffc02208 /* TWI Slave Mode Control Register */ +#define TWI1_SLAVE_CTL 0xffc02208 /* TWI Slave Mode Control Register */ #define TWI1_SLAVE_STAT 0xffc0220c /* TWI Slave Mode Status Register */ #define TWI1_SLAVE_ADDR 0xffc02210 /* TWI Slave Mode Address Register */ -#define TWI1_MASTER_CTRL 0xffc02214 /* TWI Master Mode Control Register */ +#define TWI1_MASTER_CTL 0xffc02214 /* TWI Master Mode Control Register */ #define TWI1_MASTER_STAT 0xffc02218 /* TWI Master Mode Status Register */ #define TWI1_MASTER_ADDR 0xffc0221c /* TWI Master Mode Address Register */ #define TWI1_INT_STAT 0xffc02220 /* TWI Interrupt Status Register */ #define TWI1_INT_MASK 0xffc02224 /* TWI Interrupt Mask Register */ -#define TWI1_FIFO_CTRL 0xffc02228 /* TWI FIFO Control Register */ +#define TWI1_FIFO_CTL 0xffc02228 /* TWI FIFO Control Register */ #define TWI1_FIFO_STAT 0xffc0222c /* TWI FIFO Status Register */ #define TWI1_XMT_DATA8 0xffc02280 /* TWI FIFO Transmit Data Single Byte Register */ #define TWI1_XMT_DATA16 0xffc02284 /* TWI FIFO Transmit Data Double Byte Register */ @@ -276,10 +271,10 @@ #define USB_EP_NI0_TXINTERVAL 0xffc03e18 /* Sets the NAK response timeout on Endpoint 0 */ #define USB_EP_NI0_RXTYPE 0xffc03e1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint0 */ #define USB_EP_NI0_RXINTERVAL 0xffc03e20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint0 */ +#define USB_EP_NI0_TXCOUNT 0xffc03e28 /* Number of bytes to be written to the endpoint0 Tx FIFO */ /* USB Endpoint 1 Control Registers */ -#define USB_EP_NI0_TXCOUNT 0xffc03e28 /* Number of bytes to be written to the endpoint0 Tx FIFO */ #define USB_EP_NI1_TXMAXP 0xffc03e40 /* Maximum packet size for Host Tx endpoint1 */ #define USB_EP_NI1_TXCSR 0xffc03e44 /* Control Status register for endpoint1 */ #define USB_EP_NI1_RXMAXP 0xffc03e48 /* Maximum packet size for Host Rx endpoint1 */ @@ -289,10 +284,10 @@ #define USB_EP_NI1_TXINTERVAL 0xffc03e58 /* Sets the NAK response timeout on Endpoint1 */ #define USB_EP_NI1_RXTYPE 0xffc03e5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint1 */ #define USB_EP_NI1_RXINTERVAL 0xffc03e60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint1 */ +#define USB_EP_NI1_TXCOUNT 0xffc03e68 /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */ /* USB Endpoint 2 Control Registers */ -#define USB_EP_NI1_TXCOUNT 0xffc03e68 /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */ #define USB_EP_NI2_TXMAXP 0xffc03e80 /* Maximum packet size for Host Tx endpoint2 */ #define USB_EP_NI2_TXCSR 0xffc03e84 /* Control Status register for endpoint2 */ #define USB_EP_NI2_RXMAXP 0xffc03e88 /* Maximum packet size for Host Rx endpoint2 */ @@ -302,10 +297,10 @@ #define USB_EP_NI2_TXINTERVAL 0xffc03e98 /* Sets the NAK response timeout on Endpoint2 */ #define USB_EP_NI2_RXTYPE 0xffc03e9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint2 */ #define USB_EP_NI2_RXINTERVAL 0xffc03ea0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint2 */ +#define USB_EP_NI2_TXCOUNT 0xffc03ea8 /* Number of bytes to be written to the endpoint2 Tx FIFO */ /* USB Endpoint 3 Control Registers */ -#define USB_EP_NI2_TXCOUNT 0xffc03ea8 /* Number of bytes to be written to the endpoint2 Tx FIFO */ #define USB_EP_NI3_TXMAXP 0xffc03ec0 /* Maximum packet size for Host Tx endpoint3 */ #define USB_EP_NI3_TXCSR 0xffc03ec4 /* Control Status register for endpoint3 */ #define USB_EP_NI3_RXMAXP 0xffc03ec8 /* Maximum packet size for Host Rx endpoint3 */ @@ -315,10 +310,10 @@ #define USB_EP_NI3_TXINTERVAL 0xffc03ed8 /* Sets the NAK response timeout on Endpoint3 */ #define USB_EP_NI3_RXTYPE 0xffc03edc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint3 */ #define USB_EP_NI3_RXINTERVAL 0xffc03ee0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint3 */ +#define USB_EP_NI3_TXCOUNT 0xffc03ee8 /* Number of bytes to be written to the H124endpoint3 Tx FIFO */ /* USB Endpoint 4 Control Registers */ -#define USB_EP_NI3_TXCOUNT 0xffc03ee8 /* Number of bytes to be written to the H124endpoint3 Tx FIFO */ #define USB_EP_NI4_TXMAXP 0xffc03f00 /* Maximum packet size for Host Tx endpoint4 */ #define USB_EP_NI4_TXCSR 0xffc03f04 /* Control Status register for endpoint4 */ #define USB_EP_NI4_RXMAXP 0xffc03f08 /* Maximum packet size for Host Rx endpoint4 */ @@ -328,10 +323,10 @@ #define USB_EP_NI4_TXINTERVAL 0xffc03f18 /* Sets the NAK response timeout on Endpoint4 */ #define USB_EP_NI4_RXTYPE 0xffc03f1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint4 */ #define USB_EP_NI4_RXINTERVAL 0xffc03f20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint4 */ +#define USB_EP_NI4_TXCOUNT 0xffc03f28 /* Number of bytes to be written to the endpoint4 Tx FIFO */ /* USB Endpoint 5 Control Registers */ -#define USB_EP_NI4_TXCOUNT 0xffc03f28 /* Number of bytes to be written to the endpoint4 Tx FIFO */ #define USB_EP_NI5_TXMAXP 0xffc03f40 /* Maximum packet size for Host Tx endpoint5 */ #define USB_EP_NI5_TXCSR 0xffc03f44 /* Control Status register for endpoint5 */ #define USB_EP_NI5_RXMAXP 0xffc03f48 /* Maximum packet size for Host Rx endpoint5 */ @@ -341,10 +336,10 @@ #define USB_EP_NI5_TXINTERVAL 0xffc03f58 /* Sets the NAK response timeout on Endpoint5 */ #define USB_EP_NI5_RXTYPE 0xffc03f5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint5 */ #define USB_EP_NI5_RXINTERVAL 0xffc03f60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint5 */ +#define USB_EP_NI5_TXCOUNT 0xffc03f68 /* Number of bytes to be written to the H145endpoint5 Tx FIFO */ /* USB Endpoint 6 Control Registers */ -#define USB_EP_NI5_TXCOUNT 0xffc03f68 /* Number of bytes to be written to the H145endpoint5 Tx FIFO */ #define USB_EP_NI6_TXMAXP 0xffc03f80 /* Maximum packet size for Host Tx endpoint6 */ #define USB_EP_NI6_TXCSR 0xffc03f84 /* Control Status register for endpoint6 */ #define USB_EP_NI6_RXMAXP 0xffc03f88 /* Maximum packet size for Host Rx endpoint6 */ @@ -354,10 +349,10 @@ #define USB_EP_NI6_TXINTERVAL 0xffc03f98 /* Sets the NAK response timeout on Endpoint6 */ #define USB_EP_NI6_RXTYPE 0xffc03f9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint6 */ #define USB_EP_NI6_RXINTERVAL 0xffc03fa0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint6 */ +#define USB_EP_NI6_TXCOUNT 0xffc03fa8 /* Number of bytes to be written to the endpoint6 Tx FIFO */ /* USB Endpoint 7 Control Registers */ -#define USB_EP_NI6_TXCOUNT 0xffc03fa8 /* Number of bytes to be written to the endpoint6 Tx FIFO */ #define USB_EP_NI7_TXMAXP 0xffc03fc0 /* Maximum packet size for Host Tx endpoint7 */ #define USB_EP_NI7_TXCSR 0xffc03fc4 /* Control Status register for endpoint7 */ #define USB_EP_NI7_RXMAXP 0xffc03fc8 /* Maximum packet size for Host Rx endpoint7 */ @@ -366,8 +361,9 @@ #define USB_EP_NI7_TXTYPE 0xffc03fd4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint7 */ #define USB_EP_NI7_TXINTERVAL 0xffc03fd8 /* Sets the NAK response timeout on Endpoint7 */ #define USB_EP_NI7_RXTYPE 0xffc03fdc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint7 */ -#define USB_EP_NI7_RXINTERVAL 0xffc03ff0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */ -#define USB_EP_NI7_TXCOUNT 0xffc03ff8 /* Number of bytes to be written to the endpoint7 Tx FIFO */ +#define USB_EP_NI7_RXINTERVAL 0xffc03fe0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */ +#define USB_EP_NI7_TXCOUNT 0xffc03fe8 /* Number of bytes to be written to the endpoint7 Tx FIFO */ + #define USB_DMA_INTERRUPT 0xffc04000 /* Indicates pending interrupts for the DMA channels */ /* USB Channel 0 Config Registers */ @@ -585,36 +581,6 @@ #define GU_TRANS 0xff00 /* Transparent Color - G/U Component */ #define BV_TRANS 0xff0000 /* Transparent Color - B/V Component */ -/* Bit masks for HOST_CONTROL */ - -#define HOST_EN 0x1 /* Host Enable */ -#define HOST_END 0x2 /* Host Endianess */ -#define DATA_SIZE 0x4 /* Data Size */ -#define HOST_RST 0x8 /* Host Reset */ -#define HRDY_OVR 0x20 /* Host Ready Override */ -#define INT_MODE 0x40 /* Interrupt Mode */ -#define BT_EN 0x80 /* Bus Timeout Enable */ -#define EHW 0x100 /* Enable Host Write */ -#define EHR 0x200 /* Enable Host Read */ -#define BDR 0x400 /* Burst DMA Requests */ - -/* Bit masks for HOST_STATUS */ - -#define DMA_READY 0x1 /* DMA Ready */ -#define FIFOFULL 0x2 /* FIFO Full */ -#define FIFOEMPTY 0x4 /* FIFO Empty */ -#define DMA_COMPLETE 0x8 /* DMA Complete */ -#define HSHK 0x10 /* Host Handshake */ -#define HSTIMEOUT 0x20 /* Host Timeout */ -#define HIRQ 0x40 /* Host Interrupt Request */ -#define ALLOW_CNFG 0x80 /* Allow New Configuration */ -#define DMA_DIR 0x100 /* DMA Direction */ -#define BTE 0x200 /* Bus Timeout Enabled */ - -/* Bit masks for HOST_TIMEOUT */ - -#define COUNT_TIMEOUT 0x7ff /* Host Timeout count */ - /* Bit masks for KPAD_CTL */ #define KPAD_EN 0x1 /* Keypad Enable */ @@ -646,136 +612,6 @@ #define KPAD_SOFTEVAL_E 0x2 /* Software Programmable Force Evaluate */ -/* Bit masks for SDH_COMMAND */ - -#define CMD_IDX 0x3f /* Command Index */ -#define CMD_RSP 0x40 /* Response */ -#define CMD_L_RSP 0x80 /* Long Response */ -#define CMD_INT_E 0x100 /* Command Interrupt */ -#define CMD_PEND_E 0x200 /* Command Pending */ -#define CMD_E 0x400 /* Command Enable */ - -/* Bit masks for SDH_PWR_CTL */ - -#define PWR_ON 0x3 /* Power On */ -#if 0 -#define TBD 0x3c /* TBD */ -#endif -#define SD_CMD_OD 0x40 /* Open Drain Output */ -#define ROD_CTL 0x80 /* Rod Control */ - -/* Bit masks for SDH_CLK_CTL */ - -#define CLKDIV 0xff /* MC_CLK Divisor */ -#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */ -#define PWR_SV_E 0x200 /* Power Save Enable */ -#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */ -#define WIDE_BUS 0x800 /* Wide Bus Mode Enable */ - -/* Bit masks for SDH_RESP_CMD */ - -#define RESP_CMD 0x3f /* Response Command */ - -/* Bit masks for SDH_DATA_CTL */ - -#define DTX_E 0x1 /* Data Transfer Enable */ -#define DTX_DIR 0x2 /* Data Transfer Direction */ -#define DTX_MODE 0x4 /* Data Transfer Mode */ -#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */ -#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */ - -/* Bit masks for SDH_STATUS */ - -#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */ -#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */ -#define CMD_TIME_OUT 0x4 /* CMD Time Out */ -#define DAT_TIME_OUT 0x8 /* Data Time Out */ -#define TX_UNDERRUN 0x10 /* Transmit Underrun */ -#define RX_OVERRUN 0x20 /* Receive Overrun */ -#define CMD_RESP_END 0x40 /* CMD Response End */ -#define CMD_SENT 0x80 /* CMD Sent */ -#define DAT_END 0x100 /* Data End */ -#define START_BIT_ERR 0x200 /* Start Bit Error */ -#define DAT_BLK_END 0x400 /* Data Block End */ -#define CMD_ACT 0x800 /* CMD Active */ -#define TX_ACT 0x1000 /* Transmit Active */ -#define RX_ACT 0x2000 /* Receive Active */ -#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */ -#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */ -#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */ -#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */ -#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */ -#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */ -#define TX_DAT_RDY 0x100000 /* Transmit Data Available */ -#define RX_FIFO_RDY 0x200000 /* Receive Data Available */ - -/* Bit masks for SDH_STATUS_CLR */ - -#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */ -#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */ -#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */ -#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */ -#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */ -#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */ -#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */ -#define CMD_SENT_STAT 0x80 /* CMD Sent Status */ -#define DAT_END_STAT 0x100 /* Data End Status */ -#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */ -#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */ - -/* Bit masks for SDH_MASK0 */ - -#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */ -#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */ -#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */ -#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */ -#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */ -#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */ -#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */ -#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */ -#define DAT_END_MASK 0x100 /* Data End Mask */ -#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */ -#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */ -#define CMD_ACT_MASK 0x800 /* CMD Active Mask */ -#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */ -#define RX_ACT_MASK 0x2000 /* Receive Active Mask */ -#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */ -#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */ -#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */ -#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */ -#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */ -#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */ -#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */ -#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */ - -/* Bit masks for SDH_FIFO_CNT */ - -#define FIFO_COUNT 0x7fff /* FIFO Count */ - -/* Bit masks for SDH_E_STATUS */ - -#define SDIO_INT_DET 0x2 /* SDIO Int Detected */ -#define SD_CARD_DET 0x10 /* SD Card Detect */ - -/* Bit masks for SDH_E_MASK */ - -#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */ -#define SCD_MSK 0x40 /* Mask Card Detect */ - -/* Bit masks for SDH_CFG */ - -#define CLKS_EN 0x1 /* Clocks Enable */ -#define SD4E 0x4 /* SDIO 4-Bit Enable */ -#define MWE 0x8 /* Moving Window Enable */ -#define SD_RST 0x10 /* SDMMC Reset */ -#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */ -#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */ -#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */ - -/* Bit masks for SDH_RD_WAIT_EN */ - -#define RWR 0x1 /* Read Wait Request */ - /* Bit masks for ATAPI_CONTROL */ #define PIO_START 0x1 /* Start PIO/Reg Op */ @@ -1198,23 +1034,4 @@ #define DMA_COUNT_LOW 0xffff /* Lower 16-bits of byte count of DMA transfer for DMA master channel */ -/* Bit masks for HMDMAx_CONTROL */ - -#define HMDMAEN 0x1 /* Handshake MDMA Enable */ -#define REP 0x2 /* Handshake MDMA Request Polarity */ -#define UTE 0x8 /* Urgency Threshold Enable */ -#define OIE 0x10 /* Overflow Interrupt Enable */ -#define BDIE 0x20 /* Block Done Interrupt Enable */ -#define MBDI 0x40 /* Mask Block Done Interrupt */ -#define DRQ 0x300 /* Handshake MDMA Request Type */ -#define RBC 0x1000 /* Force Reload of BCOUNT */ -#define PS 0x2000 /* Pin Status */ -#define OI 0x4000 /* Overflow Interrupt Generated */ -#define BDI 0x8000 /* Block Done Interrupt Generated */ - -/* ******************************************* */ -/* MULTI BIT MACRO ENUMERATIONS */ -/* ******************************************* */ - - #endif /* _DEF_BF547_H */ diff --git a/arch/blackfin/mach-bf548/include/mach/defBF548.h b/arch/blackfin/mach-bf548/include/mach/defBF548.h index 3fb33b040ab..27f29481e28 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF548.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF548.h @@ -1,17 +1,12 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * - * Licensed under the ADI BSD license or the GPL-2 (or later) + * Licensed under the Clear BSD license or the GPL-2 (or later) */ #ifndef _DEF_BF548_H #define _DEF_BF548_H -/* Include all Core registers and bit definitions */ -#include <asm/def_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF548 */ - /* Include defBF54x_base.h for the set of #defines that are common to all ADSP-BF54x processors */ #include "defBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/defBF549.h b/arch/blackfin/mach-bf548/include/mach/defBF549.h index 5a04e6d4017..ac569fc1297 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF549.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF549.h @@ -1,17 +1,12 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * - * Licensed under the ADI BSD license or the GPL-2 (or later) + * Licensed under the Clear BSD license or the GPL-2 (or later) */ #ifndef _DEF_BF549_H #define _DEF_BF549_H -/* Include all Core registers and bit definitions */ -#include <asm/def_LPBlackfin.h> - -/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF549 */ - /* Include defBF54x_base.h for the set of #defines that are common to all ADSP-BF54x processors */ #include "defBF54x_base.h" diff --git a/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h b/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h index ab04d137fd8..8f6e1925779 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h @@ -1,7 +1,7 @@ /* - * Copyright 2007-2008 Analog Devices Inc. + * Copyright 2007-2010 Analog Devices Inc. * - * Licensed under the ADI BSD license or the GPL-2 (or later) + * Licensed under the Clear BSD license or the GPL-2 (or later) */ #ifndef _DEF_BF54X_H @@ -35,6 +35,7 @@ /* SIC Registers */ +#define SIC_RVECT 0xffc00108 #define SIC_IMASK0 0xffc0010c /* System Interrupt Mask Register 0 */ #define SIC_IMASK1 0xffc00110 /* System Interrupt Mask Register 1 */ #define SIC_IMASK2 0xffc00114 /* System Interrupt Mask Register 2 */ @@ -105,15 +106,15 @@ #define TWI0_REGBASE 0xffc00700 #define TWI0_CLKDIV 0xffc00700 /* Clock Divider Register */ #define TWI0_CONTROL 0xffc00704 /* TWI Control Register */ -#define TWI0_SLAVE_CTRL 0xffc00708 /* TWI Slave Mode Control Register */ +#define TWI0_SLAVE_CTL 0xffc00708 /* TWI Slave Mode Control Register */ #define TWI0_SLAVE_STAT 0xffc0070c /* TWI Slave Mode Status Register */ #define TWI0_SLAVE_ADDR 0xffc00710 /* TWI Slave Mode Address Register */ -#define TWI0_MASTER_CTRL 0xffc00714 /* TWI Master Mode Control Register */ +#define TWI0_MASTER_CTL 0xffc00714 /* TWI Master Mode Control Register */ #define TWI0_MASTER_STAT 0xffc00718 /* TWI Master Mode Status Register */ #define TWI0_MASTER_ADDR 0xffc0071c /* TWI Master Mode Address Register */ #define TWI0_INT_STAT 0xffc00720 /* TWI Interrupt Status Register */ #define TWI0_INT_MASK 0xffc00724 /* TWI Interrupt Mask Register */ -#define TWI0_FIFO_CTRL 0xffc00728 /* TWI FIFO Control Register */ +#define TWI0_FIFO_CTL 0xffc00728 /* TWI FIFO Control Register */ #define TWI0_FIFO_STAT 0xffc0072c /* TWI FIFO Status Register */ #define TWI0_XMT_DATA8 0xffc00780 /* TWI FIFO Transmit Data Single Byte Register */ #define TWI0_XMT_DATA16 0xffc00784 /* TWI FIFO Transmit Data Double Byte Register */ @@ -198,8 +199,8 @@ /* DMAC0 Registers */ -#define DMAC0_TCPER 0xffc00b0c /* DMA Controller 0 Traffic Control Periods Register */ -#define DMAC0_TCCNT 0xffc00b10 /* DMA Controller 0 Current Counts Register */ +#define DMAC0_TC_PER 0xffc00b0c /* DMA Controller 0 Traffic Control Periods Register */ +#define DMAC0_TC_CNT 0xffc00b10 /* DMA Controller 0 Current Counts Register */ /* DMA Channel 0 Registers */ @@ -688,8 +689,8 @@ /* DMAC1 Registers */ -#define DMAC1_TCPER 0xffc01b0c /* DMA Controller 1 Traffic Control Periods Register */ -#define DMAC1_TCCNT 0xffc01b10 /* DMA Controller 1 Current Counts Register */ +#define DMAC1_TC_PER 0xffc01b0c /* DMA Controller 1 Traffic Control Periods Register */ +#define DMAC1_TC_CNT 0xffc01b10 /* DMA Controller 1 Current Counts Register */ /* DMA Channel 12 Registers */ @@ -1614,14 +1615,14 @@ #define CTYPE 0x40 /* DMA Channel Type */ #define PMAP 0xf000 /* Peripheral Mapped To This Channel */ -/* Bit masks for DMACx_TCPER */ +/* Bit masks for DMACx_TC_PER */ #define DCB_TRAFFIC_PERIOD 0xf /* DCB Traffic Control Period */ #define DEB_TRAFFIC_PERIOD 0xf0 /* DEB Traffic Control Period */ #define DAB_TRAFFIC_PERIOD 0x700 /* DAB Traffic Control Period */ #define MDMA_ROUND_ROBIN_PERIOD 0xf800 /* MDMA Round Robin Period */ -/* Bit masks for DMACx_TCCNT */ +/* Bit masks for DMACx_TC_CNT */ #define DCB_TRAFFIC_COUNT 0xf /* DCB Traffic Control Count */ #define DEB_TRAFFIC_COUNT 0xf0 /* DEB Traffic Control Count */ @@ -1958,57 +1959,6 @@ #define TRUN6 0x40000000 /* Timer 6 Slave Enable Status */ #define TRUN7 0x80000000 /* Timer 7 Slave Enable Status */ -/* Bit masks for CNT_CONFIG */ - -#define CNTE 0x1 /* Counter Enable */ -#define DEBE 0x2 /* Debounce Enable */ -#define CDGINV 0x10 /* CDG Pin Polarity Invert */ -#define CUDINV 0x20 /* CUD Pin Polarity Invert */ -#define CZMINV 0x40 /* CZM Pin Polarity Invert */ -#define CNTMODE 0x700 /* Counter Operating Mode */ -#define ZMZC 0x800 /* CZM Zeroes Counter Enable */ -#define BNDMODE 0x3000 /* Boundary register Mode */ -#define INPDIS 0x8000 /* CUG and CDG Input Disable */ - -/* Bit masks for CNT_IMASK */ - -#define ICIE 0x1 /* Illegal Gray/Binary Code Interrupt Enable */ -#define UCIE 0x2 /* Up count Interrupt Enable */ -#define DCIE 0x4 /* Down count Interrupt Enable */ -#define MINCIE 0x8 /* Min Count Interrupt Enable */ -#define MAXCIE 0x10 /* Max Count Interrupt Enable */ -#define COV31IE 0x20 /* Bit 31 Overflow Interrupt Enable */ -#define COV15IE 0x40 /* Bit 15 Overflow Interrupt Enable */ -#define CZEROIE 0x80 /* Count to Zero Interrupt Enable */ -#define CZMIE 0x100 /* CZM Pin Interrupt Enable */ -#define CZMEIE 0x200 /* CZM Error Interrupt Enable */ -#define CZMZIE 0x400 /* CZM Zeroes Counter Interrupt Enable */ - -/* Bit masks for CNT_STATUS */ - -#define ICII 0x1 /* Illegal Gray/Binary Code Interrupt Identifier */ -#define UCII 0x2 /* Up count Interrupt Identifier */ -#define DCII 0x4 /* Down count Interrupt Identifier */ -#define MINCII 0x8 /* Min Count Interrupt Identifier */ -#define MAXCII 0x10 /* Max Count Interrupt Identifier */ -#define COV31II 0x20 /* Bit 31 Overflow Interrupt Identifier */ -#define COV15II 0x40 /* Bit 15 Overflow Interrupt Identifier */ -#define CZEROII 0x80 /* Count to Zero Interrupt Identifier */ -#define CZMII 0x100 /* CZM Pin Interrupt Identifier */ -#define CZMEII 0x200 /* CZM Error Interrupt Identifier */ -#define CZMZII 0x400 /* CZM Zeroes Counter Interrupt Identifier */ - -/* Bit masks for CNT_COMMAND */ - -#define W1LCNT 0xf /* Load Counter Register */ -#define W1LMIN 0xf0 /* Load Min Register */ -#define W1LMAX 0xf00 /* Load Max Register */ -#define W1ZMONCE 0x1000 /* Enable CZM Clear Counter Once */ - -/* Bit masks for CNT_DEBOUNCE */ - -#define DPRESCALE 0xf /* Load Counter Register */ - /* Bit masks for SECURE_SYSSWT */ #define EMUDABL 0x1 /* Emulation Disable. */ @@ -2044,737 +1994,6 @@ #define RESET_WDOG 0x4000 /* SW Reset Generated By Watchdog Timer */ #define RESET_SOFTWARE 0x8000 /* SW Reset Occurred Since Last Read Of SWRST */ -/* Bit masks for NFC_CTL */ - -#define WR_DLY 0xf /* Write Strobe Delay */ -#define RD_DLY 0xf0 /* Read Strobe Delay */ -#define NWIDTH 0x100 /* NAND Data Width */ -#define PG_SIZE 0x200 /* Page Size */ - -/* Bit masks for NFC_STAT */ - -#define NBUSY 0x1 /* Not Busy */ -#define WB_FULL 0x2 /* Write Buffer Full */ -#define PG_WR_STAT 0x4 /* Page Write Pending */ -#define PG_RD_STAT 0x8 /* Page Read Pending */ -#define WB_EMPTY 0x10 /* Write Buffer Empty */ - -/* Bit masks for NFC_IRQSTAT */ - -#define NBUSYIRQ 0x1 /* Not Busy IRQ */ -#define WB_OVF 0x2 /* Write Buffer Overflow */ -#define WB_EDGE 0x4 /* Write Buffer Edge Detect */ -#define RD_RDY 0x8 /* Read Data Ready */ -#define WR_DONE 0x10 /* Page Write Done */ - -/* Bit masks for NFC_IRQMASK */ - -#define MASK_BUSYIRQ 0x1 /* Mask Not Busy IRQ */ -#define MASK_WBOVF 0x2 /* Mask Write Buffer Overflow */ -#define MASK_WBEMPTY 0x4 /* Mask Write Buffer Empty */ -#define MASK_RDRDY 0x8 /* Mask Read Data Ready */ -#define MASK_WRDONE 0x10 /* Mask Write Done */ - -/* Bit masks for NFC_RST */ - -#define ECC_RST 0x1 /* ECC (and NFC counters) Reset */ - -/* Bit masks for NFC_PGCTL */ - -#define PG_RD_START 0x1 /* Page Read Start */ -#define PG_WR_START 0x2 /* Page Write Start */ - -/* Bit masks for NFC_ECC0 */ - -#define ECC0 0x7ff /* Parity Calculation Result0 */ - -/* Bit masks for NFC_ECC1 */ - -#define ECC1 0x7ff /* Parity Calculation Result1 */ - -/* Bit masks for NFC_ECC2 */ - -#define ECC2 0x7ff /* Parity Calculation Result2 */ - -/* Bit masks for NFC_ECC3 */ - -#define ECC3 0x7ff /* Parity Calculation Result3 */ - -/* Bit masks for NFC_COUNT */ - -#define ECCCNT 0x3ff /* Transfer Count */ - -/* Bit masks for CAN0_CONTROL */ - -#define SRS 0x1 /* Software Reset */ -#define DNM 0x2 /* DeviceNet Mode */ -#define ABO 0x4 /* Auto Bus On */ -#define WBA 0x10 /* Wakeup On CAN Bus Activity */ -#define SMR 0x20 /* Sleep Mode Request */ -#define CSR 0x40 /* CAN Suspend Mode Request */ -#define CCR 0x80 /* CAN Configuration Mode Request */ - -/* Bit masks for CAN0_STATUS */ - -#define WT 0x1 /* CAN Transmit Warning Flag */ -#define WR 0x2 /* CAN Receive Warning Flag */ -#define EP 0x4 /* CAN Error Passive Mode */ -#define EBO 0x8 /* CAN Error Bus Off Mode */ -#define CSA 0x40 /* CAN Suspend Mode Acknowledge */ -#define CCA 0x80 /* CAN Configuration Mode Acknowledge */ -#define MBPTR 0x1f00 /* Mailbox Pointer */ -#define TRM 0x4000 /* Transmit Mode Status */ -#define REC 0x8000 /* Receive Mode Status */ - -/* Bit masks for CAN0_DEBUG */ - -#define DEC 0x1 /* Disable Transmit/Receive Error Counters */ -#define DRI 0x2 /* Disable CANRX Input Pin */ -#define DTO 0x4 /* Disable CANTX Output Pin */ -#define DIL 0x8 /* Disable Internal Loop */ -#define MAA 0x10 /* Mode Auto-Acknowledge */ -#define MRB 0x20 /* Mode Read Back */ -#define CDE 0x8000 /* CAN Debug Mode Enable */ - -/* Bit masks for CAN0_CLOCK */ - -#define BRP 0x3ff /* CAN Bit Rate Prescaler */ - -/* Bit masks for CAN0_TIMING */ - -#define SJW 0x300 /* Synchronization Jump Width */ -#define SAM 0x80 /* Sampling */ -#define TSEG2 0x70 /* Time Segment 2 */ -#define TSEG1 0xf /* Time Segment 1 */ - -/* Bit masks for CAN0_INTR */ - -#define CANRX 0x80 /* Serial Input From Transceiver */ -#define CANTX 0x40 /* Serial Output To Transceiver */ -#define SMACK 0x8 /* Sleep Mode Acknowledge */ -#define GIRQ 0x4 /* Global Interrupt Request Status */ -#define MBTIRQ 0x2 /* Mailbox Transmit Interrupt Request */ -#define MBRIRQ 0x1 /* Mailbox Receive Interrupt Request */ - -/* Bit masks for CAN0_GIM */ - -#define EWTIM 0x1 /* Error Warning Transmit Interrupt Mask */ -#define EWRIM 0x2 /* Error Warning Receive Interrupt Mask */ -#define EPIM 0x4 /* Error Passive Interrupt Mask */ -#define BOIM 0x8 /* Bus Off Interrupt Mask */ -#define WUIM 0x10 /* Wakeup Interrupt Mask */ -#define UIAIM 0x20 /* Unimplemented Address Interrupt Mask */ -#define AAIM 0x40 /* Abort Acknowledge Interrupt Mask */ -#define RMLIM 0x80 /* Receive Message Lost Interrupt Mask */ -#define UCEIM 0x100 /* Universal Counter Exceeded Interrupt Mask */ -#define ADIM 0x400 /* Access Denied Interrupt Mask */ - -/* Bit masks for CAN0_GIS */ - -#define EWTIS 0x1 /* Error Warning Transmit Interrupt Status */ -#define EWRIS 0x2 /* Error Warning Receive Interrupt Status */ -#define EPIS 0x4 /* Error Passive Interrupt Status */ -#define BOIS 0x8 /* Bus Off Interrupt Status */ -#define WUIS 0x10 /* Wakeup Interrupt Status */ -#define UIAIS 0x20 /* Unimplemented Address Interrupt Status */ -#define AAIS 0x40 /* Abort Acknowledge Interrupt Status */ -#define RMLIS 0x80 /* Receive Message Lost Interrupt Status */ -#define UCEIS 0x100 /* Universal Counter Exceeded Interrupt Status */ -#define ADIS 0x400 /* Access Denied Interrupt Status */ - -/* Bit masks for CAN0_GIF */ - -#define EWTIF 0x1 /* Error Warning Transmit Interrupt Flag */ -#define EWRIF 0x2 /* Error Warning Receive Interrupt Flag */ -#define EPIF 0x4 /* Error Passive Interrupt Flag */ -#define BOIF 0x8 /* Bus Off Interrupt Flag */ -#define WUIF 0x10 /* Wakeup Interrupt Flag */ -#define UIAIF 0x20 /* Unimplemented Address Interrupt Flag */ -#define AAIF 0x40 /* Abort Acknowledge Interrupt Flag */ -#define RMLIF 0x80 /* Receive Message Lost Interrupt Flag */ -#define UCEIF 0x100 /* Universal Counter Exceeded Interrupt Flag */ -#define ADIF 0x400 /* Access Denied Interrupt Flag */ - -/* Bit masks for CAN0_MBTD */ - -#define TDR 0x80 /* Temporary Disable Request */ -#define TDA 0x40 /* Temporary Disable Acknowledge */ -#define TDPTR 0x1f /* Temporary Disable Pointer */ - -/* Bit masks for CAN0_UCCNF */ - -#define UCCNF 0xf /* Universal Counter Configuration */ -#define UCRC 0x20 /* Universal Counter Reload/Clear */ -#define UCCT 0x40 /* Universal Counter CAN Trigger */ -#define UCE 0x80 /* Universal Counter Enable */ - -/* Bit masks for CAN0_CEC */ - -#define RXECNT 0xff /* Receive Error Counter */ -#define TXECNT 0xff00 /* Transmit Error Counter */ - -/* Bit masks for CAN0_ESR */ - -#define FER 0x80 /* Form Error */ -#define BEF 0x40 /* Bit Error Flag */ -#define SA0 0x20 /* Stuck At Dominant */ -#define CRCE 0x10 /* CRC Error */ -#define SER 0x8 /* Stuff Bit Error */ -#define ACKE 0x4 /* Acknowledge Error */ - -/* Bit masks for CAN0_EWR */ - -#define EWLTEC 0xff00 /* Transmit Error Warning Limit */ -#define EWLREC 0xff /* Receive Error Warning Limit */ - -/* Bit masks for CAN0_AMxx_H */ - -#define FDF 0x8000 /* Filter On Data Field */ -#define FMD 0x4000 /* Full Mask Data */ -#define AMIDE 0x2000 /* Acceptance Mask Identifier Extension */ -#define BASEID 0x1ffc /* Base Identifier */ -#define EXTID_HI 0x3 /* Extended Identifier High Bits */ - -/* Bit masks for CAN0_AMxx_L */ - -#define EXTID_LO 0xffff /* Extended Identifier Low Bits */ -#define DFM 0xffff /* Data Field Mask */ - -/* Bit masks for CAN0_MBxx_ID1 */ - -#define AME 0x8000 /* Acceptance Mask Enable */ -#define RTR 0x4000 /* Remote Transmission Request */ -#define IDE 0x2000 /* Identifier Extension */ -#define BASEID 0x1ffc /* Base Identifier */ -#define EXTID_HI 0x3 /* Extended Identifier High Bits */ - -/* Bit masks for CAN0_MBxx_ID0 */ - -#define EXTID_LO 0xffff /* Extended Identifier Low Bits */ -#define DFM 0xffff /* Data Field Mask */ - -/* Bit masks for CAN0_MBxx_TIMESTAMP */ - -#define TSV 0xffff /* Time Stamp Value */ - -/* Bit masks for CAN0_MBxx_LENGTH */ - -#define DLC 0xf /* Data Length Code */ - -/* Bit masks for CAN0_MBxx_DATA3 */ - -#define CAN_BYTE0 0xff00 /* Data Field Byte 0 */ -#define CAN_BYTE1 0xff /* Data Field Byte 1 */ - -/* Bit masks for CAN0_MBxx_DATA2 */ - -#define CAN_BYTE2 0xff00 /* Data Field Byte 2 */ -#define CAN_BYTE3 0xff /* Data Field Byte 3 */ - -/* Bit masks for CAN0_MBxx_DATA1 */ - -#define CAN_BYTE4 0xff00 /* Data Field Byte 4 */ -#define CAN_BYTE5 0xff /* Data Field Byte 5 */ - -/* Bit masks for CAN0_MBxx_DATA0 */ - -#define CAN_BYTE6 0xff00 /* Data Field Byte 6 */ -#define CAN_BYTE7 0xff /* Data Field Byte 7 */ - -/* Bit masks for CAN0_MC1 */ - -#define MC0 0x1 /* Mailbox 0 Enable */ -#define MC1 0x2 /* Mailbox 1 Enable */ -#define MC2 0x4 /* Mailbox 2 Enable */ -#define MC3 0x8 /* Mailbox 3 Enable */ -#define MC4 0x10 /* Mailbox 4 Enable */ -#define MC5 0x20 /* Mailbox 5 Enable */ -#define MC6 0x40 /* Mailbox 6 Enable */ -#define MC7 0x80 /* Mailbox 7 Enable */ -#define MC8 0x100 /* Mailbox 8 Enable */ -#define MC9 0x200 /* Mailbox 9 Enable */ -#define MC10 0x400 /* Mailbox 10 Enable */ -#define MC11 0x800 /* Mailbox 11 Enable */ -#define MC12 0x1000 /* Mailbox 12 Enable */ -#define MC13 0x2000 /* Mailbox 13 Enable */ -#define MC14 0x4000 /* Mailbox 14 Enable */ -#define MC15 0x8000 /* Mailbox 15 Enable */ - -/* Bit masks for CAN0_MC2 */ - -#define MC16 0x1 /* Mailbox 16 Enable */ -#define MC17 0x2 /* Mailbox 17 Enable */ -#define MC18 0x4 /* Mailbox 18 Enable */ -#define MC19 0x8 /* Mailbox 19 Enable */ -#define MC20 0x10 /* Mailbox 20 Enable */ -#define MC21 0x20 /* Mailbox 21 Enable */ -#define MC22 0x40 /* Mailbox 22 Enable */ -#define MC23 0x80 /* Mailbox 23 Enable */ -#define MC24 0x100 /* Mailbox 24 Enable */ -#define MC25 0x200 /* Mailbox 25 Enable */ -#define MC26 0x400 /* Mailbox 26 Enable */ -#define MC27 0x800 /* Mailbox 27 Enable */ -#define MC28 0x1000 /* Mailbox 28 Enable */ -#define MC29 0x2000 /* Mailbox 29 Enable */ -#define MC30 0x4000 /* Mailbox 30 Enable */ -#define MC31 0x8000 /* Mailbox 31 Enable */ - -/* Bit masks for CAN0_MD1 */ - -#define MD0 0x1 /* Mailbox 0 Receive Enable */ -#define MD1 0x2 /* Mailbox 1 Receive Enable */ -#define MD2 0x4 /* Mailbox 2 Receive Enable */ -#define MD3 0x8 /* Mailbox 3 Receive Enable */ -#define MD4 0x10 /* Mailbox 4 Receive Enable */ -#define MD5 0x20 /* Mailbox 5 Receive Enable */ -#define MD6 0x40 /* Mailbox 6 Receive Enable */ -#define MD7 0x80 /* Mailbox 7 Receive Enable */ -#define MD8 0x100 /* Mailbox 8 Receive Enable */ -#define MD9 0x200 /* Mailbox 9 Receive Enable */ -#define MD10 0x400 /* Mailbox 10 Receive Enable */ -#define MD11 0x800 /* Mailbox 11 Receive Enable */ -#define MD12 0x1000 /* Mailbox 12 Receive Enable */ -#define MD13 0x2000 /* Mailbox 13 Receive Enable */ -#define MD14 0x4000 /* Mailbox 14 Receive Enable */ -#define MD15 0x8000 /* Mailbox 15 Receive Enable */ - -/* Bit masks for CAN0_MD2 */ - -#define MD16 0x1 /* Mailbox 16 Receive Enable */ -#define MD17 0x2 /* Mailbox 17 Receive Enable */ -#define MD18 0x4 /* Mailbox 18 Receive Enable */ -#define MD19 0x8 /* Mailbox 19 Receive Enable */ -#define MD20 0x10 /* Mailbox 20 Receive Enable */ -#define MD21 0x20 /* Mailbox 21 Receive Enable */ -#define MD22 0x40 /* Mailbox 22 Receive Enable */ -#define MD23 0x80 /* Mailbox 23 Receive Enable */ -#define MD24 0x100 /* Mailbox 24 Receive Enable */ -#define MD25 0x200 /* Mailbox 25 Receive Enable */ -#define MD26 0x400 /* Mailbox 26 Receive Enable */ -#define MD27 0x800 /* Mailbox 27 Receive Enable */ -#define MD28 0x1000 /* Mailbox 28 Receive Enable */ -#define MD29 0x2000 /* Mailbox 29 Receive Enable */ -#define MD30 0x4000 /* Mailbox 30 Receive Enable */ -#define MD31 0x8000 /* Mailbox 31 Receive Enable */ - -/* Bit masks for CAN0_RMP1 */ - -#define RMP0 0x1 /* Mailbox 0 Receive Message Pending */ -#define RMP1 0x2 /* Mailbox 1 Receive Message Pending */ -#define RMP2 0x4 /* Mailbox 2 Receive Message Pending */ -#define RMP3 0x8 /* Mailbox 3 Receive Message Pending */ -#define RMP4 0x10 /* Mailbox 4 Receive Message Pending */ -#define RMP5 0x20 /* Mailbox 5 Receive Message Pending */ -#define RMP6 0x40 /* Mailbox 6 Receive Message Pending */ -#define RMP7 0x80 /* Mailbox 7 Receive Message Pending */ -#define RMP8 0x100 /* Mailbox 8 Receive Message Pending */ -#define RMP9 0x200 /* Mailbox 9 Receive Message Pending */ -#define RMP10 0x400 /* Mailbox 10 Receive Message Pending */ -#define RMP11 0x800 /* Mailbox 11 Receive Message Pending */ -#define RMP12 0x1000 /* Mailbox 12 Receive Message Pending */ -#define RMP13 0x2000 /* Mailbox 13 Receive Message Pending */ -#define RMP14 0x4000 /* Mailbox 14 Receive Message Pending */ -#define RMP15 0x8000 /* Mailbox 15 Receive Message Pending */ - -/* Bit masks for CAN0_RMP2 */ - -#define RMP16 0x1 /* Mailbox 16 Receive Message Pending */ -#define RMP17 0x2 /* Mailbox 17 Receive Message Pending */ -#define RMP18 0x4 /* Mailbox 18 Receive Message Pending */ -#define RMP19 0x8 /* Mailbox 19 Receive Message Pending */ -#define RMP20 0x10 /* Mailbox 20 Receive Message Pending */ -#define RMP21 0x20 /* Mailbox 21 Receive Message Pending */ -#define RMP22 0x40 /* Mailbox 22 Receive Message Pending */ -#define RMP23 0x80 /* Mailbox 23 Receive Message Pending */ -#define RMP24 0x100 /* Mailbox 24 Receive Message Pending */ -#define RMP25 0x200 /* Mailbox 25 Receive Message Pending */ -#define RMP26 0x400 /* Mailbox 26 Receive Message Pending */ -#define RMP27 0x800 /* Mailbox 27 Receive Message Pending */ -#define RMP28 0x1000 /* Mailbox 28 Receive Message Pending */ -#define RMP29 0x2000 /* Mailbox 29 Receive Message Pending */ -#define RMP30 0x4000 /* Mailbox 30 Receive Message Pending */ -#define RMP31 0x8000 /* Mailbox 31 Receive Message Pending */ - -/* Bit masks for CAN0_RML1 */ - -#define RML0 0x1 /* Mailbox 0 Receive Message Lost */ -#define RML1 0x2 /* Mailbox 1 Receive Message Lost */ -#define RML2 0x4 /* Mailbox 2 Receive Message Lost */ -#define RML3 0x8 /* Mailbox 3 Receive Message Lost */ -#define RML4 0x10 /* Mailbox 4 Receive Message Lost */ -#define RML5 0x20 /* Mailbox 5 Receive Message Lost */ -#define RML6 0x40 /* Mailbox 6 Receive Message Lost */ -#define RML7 0x80 /* Mailbox 7 Receive Message Lost */ -#define RML8 0x100 /* Mailbox 8 Receive Message Lost */ -#define RML9 0x200 /* Mailbox 9 Receive Message Lost */ -#define RML10 0x400 /* Mailbox 10 Receive Message Lost */ -#define RML11 0x800 /* Mailbox 11 Receive Message Lost */ -#define RML12 0x1000 /* Mailbox 12 Receive Message Lost */ -#define RML13 0x2000 /* Mailbox 13 Receive Message Lost */ -#define RML14 0x4000 /* Mailbox 14 Receive Message Lost */ -#define RML15 0x8000 /* Mailbox 15 Receive Message Lost */ - -/* Bit masks for CAN0_RML2 */ - -#define RML16 0x1 /* Mailbox 16 Receive Message Lost */ -#define RML17 0x2 /* Mailbox 17 Receive Message Lost */ -#define RML18 0x4 /* Mailbox 18 Receive Message Lost */ -#define RML19 0x8 /* Mailbox 19 Receive Message Lost */ -#define RML20 0x10 /* Mailbox 20 Receive Message Lost */ -#define RML21 0x20 /* Mailbox 21 Receive Message Lost */ -#define RML22 0x40 /* Mailbox 22 Receive Message Lost */ -#define RML23 0x80 /* Mailbox 23 Receive Message Lost */ -#define RML24 0x100 /* Mailbox 24 Receive Message Lost */ -#define RML25 0x200 /* Mailbox 25 Receive Message Lost */ -#define RML26 0x400 /* Mailbox 26 Receive Message Lost */ -#define RML27 0x800 /* Mailbox 27 Receive Message Lost */ -#define RML28 0x1000 /* Mailbox 28 Receive Message Lost */ -#define RML29 0x2000 /* Mailbox 29 Receive Message Lost */ -#define RML30 0x4000 /* Mailbox 30 Receive Message Lost */ -#define RML31 0x8000 /* Mailbox 31 Receive Message Lost */ - -/* Bit masks for CAN0_OPSS1 */ - -#define OPSS0 0x1 /* Mailbox 0 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS1 0x2 /* Mailbox 1 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS2 0x4 /* Mailbox 2 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS3 0x8 /* Mailbox 3 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS4 0x10 /* Mailbox 4 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS5 0x20 /* Mailbox 5 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS6 0x40 /* Mailbox 6 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS7 0x80 /* Mailbox 7 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS8 0x100 /* Mailbox 8 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS9 0x200 /* Mailbox 9 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS10 0x400 /* Mailbox 10 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS11 0x800 /* Mailbox 11 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS12 0x1000 /* Mailbox 12 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS13 0x2000 /* Mailbox 13 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS14 0x4000 /* Mailbox 14 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS15 0x8000 /* Mailbox 15 Overwrite Protection/Single-Shot Transmission Enable */ - -/* Bit masks for CAN0_OPSS2 */ - -#define OPSS16 0x1 /* Mailbox 16 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS17 0x2 /* Mailbox 17 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS18 0x4 /* Mailbox 18 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS19 0x8 /* Mailbox 19 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS20 0x10 /* Mailbox 20 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS21 0x20 /* Mailbox 21 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS22 0x40 /* Mailbox 22 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS23 0x80 /* Mailbox 23 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS24 0x100 /* Mailbox 24 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS25 0x200 /* Mailbox 25 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS26 0x400 /* Mailbox 26 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS27 0x800 /* Mailbox 27 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS28 0x1000 /* Mailbox 28 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS29 0x2000 /* Mailbox 29 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS30 0x4000 /* Mailbox 30 Overwrite Protection/Single-Shot Transmission Enable */ -#define OPSS31 0x8000 /* Mailbox 31 Overwrite Protection/Single-Shot Transmission Enable */ - -/* Bit masks for CAN0_TRS1 */ - -#define TRS0 0x1 /* Mailbox 0 Transmit Request Set */ -#define TRS1 0x2 /* Mailbox 1 Transmit Request Set */ -#define TRS2 0x4 /* Mailbox 2 Transmit Request Set */ -#define TRS3 0x8 /* Mailbox 3 Transmit Request Set */ -#define TRS4 0x10 /* Mailbox 4 Transmit Request Set */ -#define TRS5 0x20 /* Mailbox 5 Transmit Request Set */ -#define TRS6 0x40 /* Mailbox 6 Transmit Request Set */ -#define TRS7 0x80 /* Mailbox 7 Transmit Request Set */ -#define TRS8 0x100 /* Mailbox 8 Transmit Request Set */ -#define TRS9 0x200 /* Mailbox 9 Transmit Request Set */ -#define TRS10 0x400 /* Mailbox 10 Transmit Request Set */ -#define TRS11 0x800 /* Mailbox 11 Transmit Request Set */ -#define TRS12 0x1000 /* Mailbox 12 Transmit Request Set */ -#define TRS13 0x2000 /* Mailbox 13 Transmit Request Set */ -#define TRS14 0x4000 /* Mailbox 14 Transmit Request Set */ -#define TRS15 0x8000 /* Mailbox 15 Transmit Request Set */ - -/* Bit masks for CAN0_TRS2 */ - -#define TRS16 0x1 /* Mailbox 16 Transmit Request Set */ -#define TRS17 0x2 /* Mailbox 17 Transmit Request Set */ -#define TRS18 0x4 /* Mailbox 18 Transmit Request Set */ -#define TRS19 0x8 /* Mailbox 19 Transmit Request Set */ -#define TRS20 0x10 /* Mailbox 20 Transmit Request Set */ -#define TRS21 0x20 /* Mailbox 21 Transmit Request Set */ -#define TRS22 0x40 /* Mailbox 22 Transmit Request Set */ -#define TRS23 0x80 /* Mailbox 23 Transmit Request Set */ -#define TRS24 0x100 /* Mailbox 24 Transmit Request Set */ -#define TRS25 0x200 /* Mailbox 25 Transmit Request Set */ -#define TRS26 0x400 /* Mailbox 26 Transmit Request Set */ -#define TRS27 0x800 /* Mailbox 27 Transmit Request Set */ -#define TRS28 0x1000 /* Mailbox 28 Transmit Request Set */ -#define TRS29 0x2000 /* Mailbox 29 Transmit Request Set */ -#define TRS30 0x4000 /* Mailbox 30 Transmit Request Set */ -#define TRS31 0x8000 /* Mailbox 31 Transmit Request Set */ - -/* Bit masks for CAN0_TRR1 */ - -#define TRR0 0x1 /* Mailbox 0 Transmit Request Reset */ -#define TRR1 0x2 /* Mailbox 1 Transmit Request Reset */ -#define TRR2 0x4 /* Mailbox 2 Transmit Request Reset */ -#define TRR3 0x8 /* Mailbox 3 Transmit Request Reset */ -#define TRR4 0x10 /* Mailbox 4 Transmit Request Reset */ -#define TRR5 0x20 /* Mailbox 5 Transmit Request Reset */ -#define TRR6 0x40 /* Mailbox 6 Transmit Request Reset */ -#define TRR7 0x80 /* Mailbox 7 Transmit Request Reset */ -#define TRR8 0x100 /* Mailbox 8 Transmit Request Reset */ -#define TRR9 0x200 /* Mailbox 9 Transmit Request Reset */ -#define TRR10 0x400 /* Mailbox 10 Transmit Request Reset */ -#define TRR11 0x800 /* Mailbox 11 Transmit Request Reset */ -#define TRR12 0x1000 /* Mailbox 12 Transmit Request Reset */ -#define TRR13 0x2000 /* Mailbox 13 Transmit Request Reset */ -#define TRR14 0x4000 /* Mailbox 14 Transmit Request Reset */ -#define TRR15 0x8000 /* Mailbox 15 Transmit Request Reset */ - -/* Bit masks for CAN0_TRR2 */ - -#define TRR16 0x1 /* Mailbox 16 Transmit Request Reset */ -#define TRR17 0x2 /* Mailbox 17 Transmit Request Reset */ -#define TRR18 0x4 /* Mailbox 18 Transmit Request Reset */ -#define TRR19 0x8 /* Mailbox 19 Transmit Request Reset */ -#define TRR20 0x10 /* Mailbox 20 Transmit Request Reset */ -#define TRR21 0x20 /* Mailbox 21 Transmit Request Reset */ -#define TRR22 0x40 /* Mailbox 22 Transmit Request Reset */ -#define TRR23 0x80 /* Mailbox 23 Transmit Request Reset */ -#define TRR24 0x100 /* Mailbox 24 Transmit Request Reset */ -#define TRR25 0x200 /* Mailbox 25 Transmit Request Reset */ -#define TRR26 0x400 /* Mailbox 26 Transmit Request Reset */ -#define TRR27 0x800 /* Mailbox 27 Transmit Request Reset */ -#define TRR28 0x1000 /* Mailbox 28 Transmit Request Reset */ -#define TRR29 0x2000 /* Mailbox 29 Transmit Request Reset */ -#define TRR30 0x4000 /* Mailbox 30 Transmit Request Reset */ -#define TRR31 0x8000 /* Mailbox 31 Transmit Request Reset */ - -/* Bit masks for CAN0_AA1 */ - -#define AA0 0x1 /* Mailbox 0 Abort Acknowledge */ -#define AA1 0x2 /* Mailbox 1 Abort Acknowledge */ -#define AA2 0x4 /* Mailbox 2 Abort Acknowledge */ -#define AA3 0x8 /* Mailbox 3 Abort Acknowledge */ -#define AA4 0x10 /* Mailbox 4 Abort Acknowledge */ -#define AA5 0x20 /* Mailbox 5 Abort Acknowledge */ -#define AA6 0x40 /* Mailbox 6 Abort Acknowledge */ -#define AA7 0x80 /* Mailbox 7 Abort Acknowledge */ -#define AA8 0x100 /* Mailbox 8 Abort Acknowledge */ -#define AA9 0x200 /* Mailbox 9 Abort Acknowledge */ -#define AA10 0x400 /* Mailbox 10 Abort Acknowledge */ -#define AA11 0x800 /* Mailbox 11 Abort Acknowledge */ -#define AA12 0x1000 /* Mailbox 12 Abort Acknowledge */ -#define AA13 0x2000 /* Mailbox 13 Abort Acknowledge */ -#define AA14 0x4000 /* Mailbox 14 Abort Acknowledge */ -#define AA15 0x8000 /* Mailbox 15 Abort Acknowledge */ - -/* Bit masks for CAN0_AA2 */ - -#define AA16 0x1 /* Mailbox 16 Abort Acknowledge */ -#define AA17 0x2 /* Mailbox 17 Abort Acknowledge */ -#define AA18 0x4 /* Mailbox 18 Abort Acknowledge */ -#define AA19 0x8 /* Mailbox 19 Abort Acknowledge */ -#define AA20 0x10 /* Mailbox 20 Abort Acknowledge */ -#define AA21 0x20 /* Mailbox 21 Abort Acknowledge */ -#define AA22 0x40 /* Mailbox 22 Abort Acknowledge */ -#define AA23 0x80 /* Mailbox 23 Abort Acknowledge */ -#define AA24 0x100 /* Mailbox 24 Abort Acknowledge */ -#define AA25 0x200 /* Mailbox 25 Abort Acknowledge */ -#define AA26 0x400 /* Mailbox 26 Abort Acknowledge */ -#define AA27 0x800 /* Mailbox 27 Abort Acknowledge */ -#define AA28 0x1000 /* Mailbox 28 Abort Acknowledge */ -#define AA29 0x2000 /* Mailbox 29 Abort Acknowledge */ -#define AA30 0x4000 /* Mailbox 30 Abort Acknowledge */ -#define AA31 0x8000 /* Mailbox 31 Abort Acknowledge */ - -/* Bit masks for CAN0_TA1 */ - -#define TA0 0x1 /* Mailbox 0 Transmit Acknowledge */ -#define TA1 0x2 /* Mailbox 1 Transmit Acknowledge */ -#define TA2 0x4 /* Mailbox 2 Transmit Acknowledge */ -#define TA3 0x8 /* Mailbox 3 Transmit Acknowledge */ -#define TA4 0x10 /* Mailbox 4 Transmit Acknowledge */ -#define TA5 0x20 /* Mailbox 5 Transmit Acknowledge */ -#define TA6 0x40 /* Mailbox 6 Transmit Acknowledge */ -#define TA7 0x80 /* Mailbox 7 Transmit Acknowledge */ -#define TA8 0x100 /* Mailbox 8 Transmit Acknowledge */ -#define TA9 0x200 /* Mailbox 9 Transmit Acknowledge */ -#define TA10 0x400 /* Mailbox 10 Transmit Acknowledge */ -#define TA11 0x800 /* Mailbox 11 Transmit Acknowledge */ -#define TA12 0x1000 /* Mailbox 12 Transmit Acknowledge */ -#define TA13 0x2000 /* Mailbox 13 Transmit Acknowledge */ -#define TA14 0x4000 /* Mailbox 14 Transmit Acknowledge */ -#define TA15 0x8000 /* Mailbox 15 Transmit Acknowledge */ - -/* Bit masks for CAN0_TA2 */ - -#define TA16 0x1 /* Mailbox 16 Transmit Acknowledge */ -#define TA17 0x2 /* Mailbox 17 Transmit Acknowledge */ -#define TA18 0x4 /* Mailbox 18 Transmit Acknowledge */ -#define TA19 0x8 /* Mailbox 19 Transmit Acknowledge */ -#define TA20 0x10 /* Mailbox 20 Transmit Acknowledge */ -#define TA21 0x20 /* Mailbox 21 Transmit Acknowledge */ -#define TA22 0x40 /* Mailbox 22 Transmit Acknowledge */ -#define TA23 0x80 /* Mailbox 23 Transmit Acknowledge */ -#define TA24 0x100 /* Mailbox 24 Transmit Acknowledge */ -#define TA25 0x200 /* Mailbox 25 Transmit Acknowledge */ -#define TA26 0x400 /* Mailbox 26 Transmit Acknowledge */ -#define TA27 0x800 /* Mailbox 27 Transmit Acknowledge */ -#define TA28 0x1000 /* Mailbox 28 Transmit Acknowledge */ -#define TA29 0x2000 /* Mailbox 29 Transmit Acknowledge */ -#define TA30 0x4000 /* Mailbox 30 Transmit Acknowledge */ -#define TA31 0x8000 /* Mailbox 31 Transmit Acknowledge */ - -/* Bit masks for CAN0_RFH1 */ - -#define RFH0 0x1 /* Mailbox 0 Remote Frame Handling Enable */ -#define RFH1 0x2 /* Mailbox 1 Remote Frame Handling Enable */ -#define RFH2 0x4 /* Mailbox 2 Remote Frame Handling Enable */ -#define RFH3 0x8 /* Mailbox 3 Remote Frame Handling Enable */ -#define RFH4 0x10 /* Mailbox 4 Remote Frame Handling Enable */ -#define RFH5 0x20 /* Mailbox 5 Remote Frame Handling Enable */ -#define RFH6 0x40 /* Mailbox 6 Remote Frame Handling Enable */ -#define RFH7 0x80 /* Mailbox 7 Remote Frame Handling Enable */ -#define RFH8 0x100 /* Mailbox 8 Remote Frame Handling Enable */ -#define RFH9 0x200 /* Mailbox 9 Remote Frame Handling Enable */ -#define RFH10 0x400 /* Mailbox 10 Remote Frame Handling Enable */ -#define RFH11 0x800 /* Mailbox 11 Remote Frame Handling Enable */ -#define RFH12 0x1000 /* Mailbox 12 Remote Frame Handling Enable */ -#define RFH13 0x2000 /* Mailbox 13 Remote Frame Handling Enable */ -#define RFH14 0x4000 /* Mailbox 14 Remote Frame Handling Enable */ -#define RFH15 0x8000 /* Mailbox 15 Remote Frame Handling Enable */ - -/* Bit masks for CAN0_RFH2 */ - -#define RFH16 0x1 /* Mailbox 16 Remote Frame Handling Enable */ -#define RFH17 0x2 /* Mailbox 17 Remote Frame Handling Enable */ -#define RFH18 0x4 /* Mailbox 18 Remote Frame Handling Enable */ -#define RFH19 0x8 /* Mailbox 19 Remote Frame Handling Enable */ -#define RFH20 0x10 /* Mailbox 20 Remote Frame Handling Enable */ -#define RFH21 0x20 /* Mailbox 21 Remote Frame Handling Enable */ -#define RFH22 0x40 /* Mailbox 22 Remote Frame Handling Enable */ -#define RFH23 0x80 /* Mailbox 23 Remote Frame Handling Enable */ -#define RFH24 0x100 /* Mailbox 24 Remote Frame Handling Enable */ -#define RFH25 0x200 /* Mailbox 25 Remote Frame Handling Enable */ -#define RFH26 0x400 /* Mailbox 26 Remote Frame Handling Enable */ -#define RFH27 0x800 /* Mailbox 27 Remote Frame Handling Enable */ -#define RFH28 0x1000 /* Mailbox 28 Remote Frame Handling Enable */ -#define RFH29 0x2000 /* Mailbox 29 Remote Frame Handling Enable */ -#define RFH30 0x4000 /* Mailbox 30 Remote Frame Handling Enable */ -#define RFH31 0x8000 /* Mailbox 31 Remote Frame Handling Enable */ - -/* Bit masks for CAN0_MBIM1 */ - -#define MBIM0 0x1 /* Mailbox 0 Mailbox Interrupt Mask */ -#define MBIM1 0x2 /* Mailbox 1 Mailbox Interrupt Mask */ -#define MBIM2 0x4 /* Mailbox 2 Mailbox Interrupt Mask */ -#define MBIM3 0x8 /* Mailbox 3 Mailbox Interrupt Mask */ -#define MBIM4 0x10 /* Mailbox 4 Mailbox Interrupt Mask */ -#define MBIM5 0x20 /* Mailbox 5 Mailbox Interrupt Mask */ -#define MBIM6 0x40 /* Mailbox 6 Mailbox Interrupt Mask */ -#define MBIM7 0x80 /* Mailbox 7 Mailbox Interrupt Mask */ -#define MBIM8 0x100 /* Mailbox 8 Mailbox Interrupt Mask */ -#define MBIM9 0x200 /* Mailbox 9 Mailbox Interrupt Mask */ -#define MBIM10 0x400 /* Mailbox 10 Mailbox Interrupt Mask */ -#define MBIM11 0x800 /* Mailbox 11 Mailbox Interrupt Mask */ -#define MBIM12 0x1000 /* Mailbox 12 Mailbox Interrupt Mask */ -#define MBIM13 0x2000 /* Mailbox 13 Mailbox Interrupt Mask */ -#define MBIM14 0x4000 /* Mailbox 14 Mailbox Interrupt Mask */ -#define MBIM15 0x8000 /* Mailbox 15 Mailbox Interrupt Mask */ - -/* Bit masks for CAN0_MBIM2 */ - -#define MBIM16 0x1 /* Mailbox 16 Mailbox Interrupt Mask */ -#define MBIM17 0x2 /* Mailbox 17 Mailbox Interrupt Mask */ -#define MBIM18 0x4 /* Mailbox 18 Mailbox Interrupt Mask */ -#define MBIM19 0x8 /* Mailbox 19 Mailbox Interrupt Mask */ -#define MBIM20 0x10 /* Mailbox 20 Mailbox Interrupt Mask */ -#define MBIM21 0x20 /* Mailbox 21 Mailbox Interrupt Mask */ -#define MBIM22 0x40 /* Mailbox 22 Mailbox Interrupt Mask */ -#define MBIM23 0x80 /* Mailbox 23 Mailbox Interrupt Mask */ -#define MBIM24 0x100 /* Mailbox 24 Mailbox Interrupt Mask */ -#define MBIM25 0x200 /* Mailbox 25 Mailbox Interrupt Mask */ -#define MBIM26 0x400 /* Mailbox 26 Mailbox Interrupt Mask */ -#define MBIM27 0x800 /* Mailbox 27 Mailbox Interrupt Mask */ -#define MBIM28 0x1000 /* Mailbox 28 Mailbox Interrupt Mask */ -#define MBIM29 0x2000 /* Mailbox 29 Mailbox Interrupt Mask */ -#define MBIM30 0x4000 /* Mailbox 30 Mailbox Interrupt Mask */ -#define MBIM31 0x8000 /* Mailbox 31 Mailbox Interrupt Mask */ - -/* Bit masks for CAN0_MBTIF1 */ - -#define MBTIF0 0x1 /* Mailbox 0 Mailbox Transmit Interrupt Flag */ -#define MBTIF1 0x2 /* Mailbox 1 Mailbox Transmit Interrupt Flag */ -#define MBTIF2 0x4 /* Mailbox 2 Mailbox Transmit Interrupt Flag */ -#define MBTIF3 0x8 /* Mailbox 3 Mailbox Transmit Interrupt Flag */ -#define MBTIF4 0x10 /* Mailbox 4 Mailbox Transmit Interrupt Flag */ -#define MBTIF5 0x20 /* Mailbox 5 Mailbox Transmit Interrupt Flag */ -#define MBTIF6 0x40 /* Mailbox 6 Mailbox Transmit Interrupt Flag */ -#define MBTIF7 0x80 /* Mailbox 7 Mailbox Transmit Interrupt Flag */ -#define MBTIF8 0x100 /* Mailbox 8 Mailbox Transmit Interrupt Flag */ -#define MBTIF9 0x200 /* Mailbox 9 Mailbox Transmit Interrupt Flag */ -#define MBTIF10 0x400 /* Mailbox 10 Mailbox Transmit Interrupt Flag */ -#define MBTIF11 0x800 /* Mailbox 11 Mailbox Transmit Interrupt Flag */ -#define MBTIF12 0x1000 /* Mailbox 12 Mailbox Transmit Interrupt Flag */ -#define MBTIF13 0x2000 /* Mailbox 13 Mailbox Transmit Interrupt Flag */ -#define MBTIF14 0x4000 /* Mailbox 14 Mailbox Transmit Interrupt Flag */ -#define MBTIF15 0x8000 /* Mailbox 15 Mailbox Transmit Interrupt Flag */ - -/* Bit masks for CAN0_MBTIF2 */ - -#define MBTIF16 0x1 /* Mailbox 16 Mailbox Transmit Interrupt Flag */ -#define MBTIF17 0x2 /* Mailbox 17 Mailbox Transmit Interrupt Flag */ -#define MBTIF18 0x4 /* Mailbox 18 Mailbox Transmit Interrupt Flag */ -#define MBTIF19 0x8 /* Mailbox 19 Mailbox Transmit Interrupt Flag */ -#define MBTIF20 0x10 /* Mailbox 20 Mailbox Transmit Interrupt Flag */ -#define MBTIF21 0x20 /* Mailbox 21 Mailbox Transmit Interrupt Flag */ -#define MBTIF22 0x40 /* Mailbox 22 Mailbox Transmit Interrupt Flag */ -#define MBTIF23 0x80 /* Mailbox 23 Mailbox Transmit Interrupt Flag */ -#define MBTIF24 0x100 /* Mailbox 24 Mailbox Transmit Interrupt Flag */ -#define MBTIF25 0x200 /* Mailbox 25 Mailbox Transmit Interrupt Flag */ -#define MBTIF26 0x400 /* Mailbox 26 Mailbox Transmit Interrupt Flag */ -#define MBTIF27 0x800 /* Mailbox 27 Mailbox Transmit Interrupt Flag */ -#define MBTIF28 0x1000 /* Mailbox 28 Mailbox Transmit Interrupt Flag */ -#define MBTIF29 0x2000 /* Mailbox 29 Mailbox Transmit Interrupt Flag */ -#define MBTIF30 0x4000 /* Mailbox 30 Mailbox Transmit Interrupt Flag */ -#define MBTIF31 0x8000 /* Mailbox 31 Mailbox Transmit Interrupt Flag */ - -/* Bit masks for CAN0_MBRIF1 */ - -#define MBRIF0 0x1 /* Mailbox 0 Mailbox Receive Interrupt Flag */ -#define MBRIF1 0x2 /* Mailbox 1 Mailbox Receive Interrupt Flag */ -#define MBRIF2 0x4 /* Mailbox 2 Mailbox Receive Interrupt Flag */ -#define MBRIF3 0x8 /* Mailbox 3 Mailbox Receive Interrupt Flag */ -#define MBRIF4 0x10 /* Mailbox 4 Mailbox Receive Interrupt Flag */ -#define MBRIF5 0x20 /* Mailbox 5 Mailbox Receive Interrupt Flag */ -#define MBRIF6 0x40 /* Mailbox 6 Mailbox Receive Interrupt Flag */ -#define MBRIF7 0x80 /* Mailbox 7 Mailbox Receive Interrupt Flag */ -#define MBRIF8 0x100 /* Mailbox 8 Mailbox Receive Interrupt Flag */ -#define MBRIF9 0x200 /* Mailbox 9 Mailbox Receive Interrupt Flag */ -#define MBRIF10 0x400 /* Mailbox 10 Mailbox Receive Interrupt Flag */ -#define MBRIF11 0x800 /* Mailbox 11 Mailbox Receive Interrupt Flag */ -#define MBRIF12 0x1000 /* Mailbox 12 Mailbox Receive Interrupt Flag */ -#define MBRIF13 0x2000 /* Mailbox 13 Mailbox Receive Interrupt Flag */ -#define MBRIF14 0x4000 /* Mailbox 14 Mailbox Receive Interrupt Flag */ -#define MBRIF15 0x8000 /* Mailbox 15 Mailbox Receive Interrupt Flag */ - -/* Bit masks for CAN0_MBRIF2 */ - -#define MBRIF16 0x1 /* Mailbox 16 Mailbox Receive Interrupt Flag */ -#define MBRIF17 0x2 /* Mailbox 17 Mailbox Receive Interrupt Flag */ -#define MBRIF18 0x4 /* Mailbox 18 Mailbox Receive Interrupt Flag */ -#define MBRIF19 0x8 /* Mailbox 19 Mailbox Receive Interrupt Flag */ -#define MBRIF20 0x10 /* Mailbox 20 Mailbox Receive Interrupt Flag */ -#define MBRIF21 0x20 /* Mailbox 21 Mailbox Receive Interrupt Flag */ -#define MBRIF22 0x40 /* Mailbox 22 Mailbox Receive Interrupt Flag */ -#define MBRIF23 0x80 /* Mailbox 23 Mailbox Receive Interrupt Flag */ -#define MBRIF24 0x100 /* Mailbox 24 Mailbox Receive Interrupt Flag */ -#define MBRIF25 0x200 /* Mailbox 25 Mailbox Receive Interrupt Flag */ -#define MBRIF26 0x400 /* Mailbox 26 Mailbox Receive Interrupt Flag */ -#define MBRIF27 0x800 /* Mailbox 27 Mailbox Receive Interrupt Flag */ -#define MBRIF28 0x1000 /* Mailbox 28 Mailbox Receive Interrupt Flag */ -#define MBRIF29 0x2000 /* Mailbox 29 Mailbox Receive Interrupt Flag */ -#define MBRIF30 0x4000 /* Mailbox 30 Mailbox Receive Interrupt Flag */ -#define MBRIF31 0x8000 /* Mailbox 31 Mailbox Receive Interrupt Flag */ - /* Bit masks for EPPIx_STATUS */ #define CFIFO_ERR 0x1 /* Chroma FIFO Error */ @@ -2843,294 +2062,6 @@ #define LOW_EVEN 0xff0000 /* Lower Limit for Even Bytes (Luma) */ #define HIGH_EVEN 0xff000000 /* Upper Limit for Even Bytes (Luma) */ -/* Bit masks for SPIx_BAUD */ - -#define SPI_BAUD 0xffff /* Baud Rate */ - -/* Bit masks for SPIx_CTL */ - -#define SPE 0x4000 /* SPI Enable */ -#define WOM 0x2000 /* Write Open Drain Master */ -#define MSTR 0x1000 /* Master Mode */ -#define CPOL 0x800 /* Clock Polarity */ -#define CPHA 0x400 /* Clock Phase */ -#define LSBF 0x200 /* LSB First */ -#define SIZE 0x100 /* Size of Words */ -#define EMISO 0x20 /* Enable MISO Output */ -#define PSSE 0x10 /* Slave-Select Enable */ -#define GM 0x8 /* Get More Data */ -#define SZ 0x4 /* Send Zero */ -#define TIMOD 0x3 /* Transfer Initiation Mode */ - -/* Bit masks for SPIx_FLG */ - -#define FLS1 0x2 /* Slave Select Enable 1 */ -#define FLS2 0x4 /* Slave Select Enable 2 */ -#define FLS3 0x8 /* Slave Select Enable 3 */ -#define FLG1 0x200 /* Slave Select Value 1 */ -#define FLG2 0x400 /* Slave Select Value 2 */ -#define FLG3 0x800 /* Slave Select Value 3 */ - -/* Bit masks for SPIx_STAT */ - -#define TXCOL 0x40 /* Transmit Collision Error */ -#define RXS 0x20 /* RDBR Data Buffer Status */ -#define RBSY 0x10 /* Receive Error */ -#define TXS 0x8 /* TDBR Data Buffer Status */ -#define TXE 0x4 /* Transmission Error */ -#define MODF 0x2 /* Mode Fault Error */ -#define SPIF 0x1 /* SPI Finished */ - -/* Bit masks for SPIx_TDBR */ - -#define TDBR 0xffff /* Transmit Data Buffer */ - -/* Bit masks for SPIx_RDBR */ - -#define RDBR 0xffff /* Receive Data Buffer */ - -/* Bit masks for SPIx_SHADOW */ - -#define SHADOW 0xffff /* RDBR Shadow */ - -/* ************************************************ */ -/* The TWI bit masks fields are from the ADSP-BF538 */ -/* and they have not been verified as the final */ -/* ones for the Moab processors ... bz 1/19/2007 */ -/* ************************************************ */ - -/* Bit masks for TWIx_CONTROL */ - -#define PRESCALE 0x7f /* Prescale Value */ -#define TWI_ENA 0x80 /* TWI Enable */ -#define SCCB 0x200 /* Serial Camera Control Bus */ - -/* Bit maskes for TWIx_CLKDIV */ - -#define CLKLOW 0xff /* Clock Low */ -#define CLKHI 0xff00 /* Clock High */ - -/* Bit maskes for TWIx_SLAVE_CTL */ - -#define SEN 0x1 /* Slave Enable */ -#define STDVAL 0x4 /* Slave Transmit Data Valid */ -#define NAK 0x8 /* Not Acknowledge */ -#define GEN 0x10 /* General Call Enable */ - -/* Bit maskes for TWIx_SLAVE_ADDR */ - -#define SADDR 0x7f /* Slave Mode Address */ - -/* Bit maskes for TWIx_SLAVE_STAT */ - -#define SDIR 0x1 /* Slave Transfer Direction */ -#define GCALL 0x2 /* General Call */ - -/* Bit maskes for TWIx_MASTER_CTL */ - -#define MEN 0x1 /* Master Mode Enable */ -#define MDIR 0x4 /* Master Transfer Direction */ -#define FAST 0x8 /* Fast Mode */ -#define STOP 0x10 /* Issue Stop Condition */ -#define RSTART 0x20 /* Repeat Start */ -#define DCNT 0x3fc0 /* Data Transfer Count */ -#define SDAOVR 0x4000 /* Serial Data Override */ -#define SCLOVR 0x8000 /* Serial Clock Override */ - -/* Bit maskes for TWIx_MASTER_ADDR */ - -#define MADDR 0x7f /* Master Mode Address */ - -/* Bit maskes for TWIx_MASTER_STAT */ - -#define MPROG 0x1 /* Master Transfer in Progress */ -#define LOSTARB 0x2 /* Lost Arbitration */ -#define ANAK 0x4 /* Address Not Acknowledged */ -#define DNAK 0x8 /* Data Not Acknowledged */ -#define BUFRDERR 0x10 /* Buffer Read Error */ -#define BUFWRERR 0x20 /* Buffer Write Error */ -#define SDASEN 0x40 /* Serial Data Sense */ -#define SCLSEN 0x80 /* Serial Clock Sense */ -#define BUSBUSY 0x100 /* Bus Busy */ - -/* Bit maskes for TWIx_FIFO_CTL */ - -#define XMTFLUSH 0x1 /* Transmit Buffer Flush */ -#define RCVFLUSH 0x2 /* Receive Buffer Flush */ -#define XMTINTLEN 0x4 /* Transmit Buffer Interrupt Length */ -#define RCVINTLEN 0x8 /* Receive Buffer Interrupt Length */ - -/* Bit maskes for TWIx_FIFO_STAT */ - -#define XMTSTAT 0x3 /* Transmit FIFO Status */ -#define RCVSTAT 0xc /* Receive FIFO Status */ - -/* Bit maskes for TWIx_INT_MASK */ - -#define SINITM 0x1 /* Slave Transfer Initiated Interrupt Mask */ -#define SCOMPM 0x2 /* Slave Transfer Complete Interrupt Mask */ -#define SERRM 0x4 /* Slave Transfer Error Interrupt Mask */ -#define SOVFM 0x8 /* Slave Overflow Interrupt Mask */ -#define MCOMPM 0x10 /* Master Transfer Complete Interrupt Mask */ -#define MERRM 0x20 /* Master Transfer Error Interrupt Mask */ -#define XMTSERVM 0x40 /* Transmit FIFO Service Interrupt Mask */ -#define RCVSERVM 0x80 /* Receive FIFO Service Interrupt Mask */ - -/* Bit maskes for TWIx_INT_STAT */ - -#define SINIT 0x1 /* Slave Transfer Initiated */ -#define SCOMP 0x2 /* Slave Transfer Complete */ -#define SERR 0x4 /* Slave Transfer Error */ -#define SOVF 0x8 /* Slave Overflow */ -#define MCOMP 0x10 /* Master Transfer Complete */ -#define MERR 0x20 /* Master Transfer Error */ -#define XMTSERV 0x40 /* Transmit FIFO Service */ -#define RCVSERV 0x80 /* Receive FIFO Service */ - -/* Bit maskes for TWIx_XMT_DATA8 */ - -#define XMTDATA8 0xff /* Transmit FIFO 8-Bit Data */ - -/* Bit maskes for TWIx_XMT_DATA16 */ - -#define XMTDATA16 0xffff /* Transmit FIFO 16-Bit Data */ - -/* Bit maskes for TWIx_RCV_DATA8 */ - -#define RCVDATA8 0xff /* Receive FIFO 8-Bit Data */ - -/* Bit maskes for TWIx_RCV_DATA16 */ - -#define RCVDATA16 0xffff /* Receive FIFO 16-Bit Data */ - -/* Bit masks for SPORTx_TCR1 */ - -#define TCKFE 0x4000 /* Clock Falling Edge Select */ -#define LATFS 0x2000 /* Late Transmit Frame Sync */ -#define LTFS 0x1000 /* Low Transmit Frame Sync Select */ -#define DITFS 0x800 /* Data-Independent Transmit Frame Sync Select */ -#define TFSR 0x400 /* Transmit Frame Sync Required Select */ -#define ITFS 0x200 /* Internal Transmit Frame Sync Select */ -#define TLSBIT 0x10 /* Transmit Bit Order */ -#define TDTYPE 0xc /* Data Formatting Type Select */ -#define ITCLK 0x2 /* Internal Transmit Clock Select */ -#define TSPEN 0x1 /* Transmit Enable */ - -/* Bit masks for SPORTx_TCR2 */ - -#define TRFST 0x400 /* Left/Right Order */ -#define TSFSE 0x200 /* Transmit Stereo Frame Sync Enable */ -#define TXSE 0x100 /* TxSEC Enable */ -#define SLEN_T 0x1f /* SPORT Word Length */ - -/* Bit masks for SPORTx_RCR1 */ - -#define RCKFE 0x4000 /* Clock Falling Edge Select */ -#define LARFS 0x2000 /* Late Receive Frame Sync */ -#define LRFS 0x1000 /* Low Receive Frame Sync Select */ -#define RFSR 0x400 /* Receive Frame Sync Required Select */ -#define IRFS 0x200 /* Internal Receive Frame Sync Select */ -#define RLSBIT 0x10 /* Receive Bit Order */ -#define RDTYPE 0xc /* Data Formatting Type Select */ -#define IRCLK 0x2 /* Internal Receive Clock Select */ -#define RSPEN 0x1 /* Receive Enable */ - -/* Bit masks for SPORTx_RCR2 */ - -#define RRFST 0x400 /* Left/Right Order */ -#define RSFSE 0x200 /* Receive Stereo Frame Sync Enable */ -#define RXSE 0x100 /* RxSEC Enable */ -#define SLEN_R 0x1f /* SPORT Word Length */ - -/* Bit masks for SPORTx_STAT */ - -#define TXHRE 0x40 /* Transmit Hold Register Empty */ -#define TOVF 0x20 /* Sticky Transmit Overflow Status */ -#define TUVF 0x10 /* Sticky Transmit Underflow Status */ -#define TXF 0x8 /* Transmit FIFO Full Status */ -#define ROVF 0x4 /* Sticky Receive Overflow Status */ -#define RUVF 0x2 /* Sticky Receive Underflow Status */ -#define RXNE 0x1 /* Receive FIFO Not Empty Status */ - -/* Bit masks for SPORTx_MCMC1 */ - -#define SP_WSIZE 0xf000 /* Window Size */ -#define SP_WOFF 0x3ff /* Windows Offset */ - -/* Bit masks for SPORTx_MCMC2 */ - -#define MFD 0xf000 /* Multi channel Frame Delay */ -#define FSDR 0x80 /* Frame Sync to Data Relationship */ -#define MCMEN 0x10 /* Multi channel Frame Mode Enable */ -#define MCDRXPE 0x8 /* Multi channel DMA Receive Packing */ -#define MCDTXPE 0x4 /* Multi channel DMA Transmit Packing */ -#define MCCRM 0x3 /* 2X Clock Recovery Mode */ - -/* Bit masks for SPORTx_CHNL */ - -#define CUR_CHNL 0x3ff /* Current Channel Indicator */ - -/* Bit masks for UARTx_LCR */ - -#if 0 -/* conflicts with legacy one in last section */ -#define WLS 0x3 /* Word Length Select */ -#endif -#define STB 0x4 /* Stop Bits */ -#define PEN 0x8 /* Parity Enable */ -#define EPS 0x10 /* Even Parity Select */ -#define STP 0x20 /* Sticky Parity */ -#define SB 0x40 /* Set Break */ - -/* Bit masks for UARTx_MCR */ - -#define XOFF 0x1 /* Transmitter Off */ -#define MRTS 0x2 /* Manual Request To Send */ -#define RFIT 0x4 /* Receive FIFO IRQ Threshold */ -#define RFRT 0x8 /* Receive FIFO RTS Threshold */ -#define LOOP_ENA 0x10 /* Loopback Mode Enable */ -#define FCPOL 0x20 /* Flow Control Pin Polarity */ -#define ARTS 0x40 /* Automatic Request To Send */ -#define ACTS 0x80 /* Automatic Clear To Send */ - -/* Bit masks for UARTx_LSR */ - -#define DR 0x1 /* Data Ready */ -#define OE 0x2 /* Overrun Error */ -#define PE 0x4 /* Parity Error */ -#define FE 0x8 /* Framing Error */ -#define BI 0x10 /* Break Interrupt */ -#define THRE 0x20 /* THR Empty */ -#define TEMT 0x40 /* Transmitter Empty */ -#define TFI 0x80 /* Transmission Finished Indicator */ - -/* Bit masks for UARTx_MSR */ - -#define SCTS 0x1 /* Sticky CTS */ -#define CTS 0x10 /* Clear To Send */ -#define RFCS 0x20 /* Receive FIFO Count Status */ - -/* Bit masks for UARTx_IER_SET & UARTx_IER_CLEAR */ - -#define ERBFI 0x1 /* Enable Receive Buffer Full Interrupt */ -#define ETBEI 0x2 /* Enable Transmit Buffer Empty Interrupt */ -#define ELSI 0x4 /* Enable Receive Status Interrupt */ -#define EDSSI 0x8 /* Enable Modem Status Interrupt */ -#define EDTPTI 0x10 /* Enable DMA Transmit PIRQ Interrupt */ -#define ETFI 0x20 /* Enable Transmission Finished Interrupt */ -#define ERFCI 0x40 /* Enable Receive FIFO Count Interrupt */ - -/* Bit masks for UARTx_GCTL */ - -#define UCEN 0x1 /* UART Enable */ -#define IREN 0x2 /* IrDA Mode Enable */ -#define TPOLC 0x4 /* IrDA TX Polarity Change */ -#define RPOLC 0x8 /* IrDA RX Polarity Change */ -#define FPE 0x10 /* Force Parity Error */ -#define FFE 0x20 /* Force Framing Error */ -#define EDBO 0x40 /* Enable Divide-by-One */ -#define EGLSI 0x80 /* Enable Global LS Interrupt */ - /* ******************************************* */ /* MULTI BIT MACRO ENUMERATIONS */ @@ -3143,46 +2074,12 @@ #define BCODE_QUICKBOOT 0x0020 /* always perform quick boot */ #define BCODE_NOBOOT 0x0030 /* always perform full boot */ -/* CNT_COMMAND bit field options */ - -#define W1LCNT_ZERO 0x0001 /* write 1 to load CNT_COUNTER with zero */ -#define W1LCNT_MIN 0x0004 /* write 1 to load CNT_COUNTER from CNT_MIN */ -#define W1LCNT_MAX 0x0008 /* write 1 to load CNT_COUNTER from CNT_MAX */ - -#define W1LMIN_ZERO 0x0010 /* write 1 to load CNT_MIN with zero */ -#define W1LMIN_CNT 0x0020 /* write 1 to load CNT_MIN from CNT_COUNTER */ -#define W1LMIN_MAX 0x0080 /* write 1 to load CNT_MIN from CNT_MAX */ - -#define W1LMAX_ZERO 0x0100 /* write 1 to load CNT_MAX with zero */ -#define W1LMAX_CNT 0x0200 /* write 1 to load CNT_MAX from CNT_COUNTER */ -#define W1LMAX_MIN 0x0400 /* write 1 to load CNT_MAX from CNT_MIN */ - -/* CNT_CONFIG bit field options */ - -#define CNTMODE_QUADENC 0x0000 /* quadrature encoder mode */ -#define CNTMODE_BINENC 0x0100 /* binary encoder mode */ -#define CNTMODE_UDCNT 0x0200 /* up/down counter mode */ -#define CNTMODE_DIRCNT 0x0400 /* direction counter mode */ -#define CNTMODE_DIRTMR 0x0500 /* direction timer mode */ - -#define BNDMODE_COMP 0x0000 /* boundary compare mode */ -#define BNDMODE_ZERO 0x1000 /* boundary compare and zero mode */ -#define BNDMODE_CAPT 0x2000 /* boundary capture mode */ -#define BNDMODE_AEXT 0x3000 /* boundary auto-extend mode */ - /* TMODE in TIMERx_CONFIG bit field options */ #define PWM_OUT 0x0001 #define WDTH_CAP 0x0002 #define EXT_CLK 0x0003 -/* UARTx_LCR bit field options */ - -#define WLS_5 0x0000 /* 5 data bits */ -#define WLS_6 0x0001 /* 6 data bits */ -#define WLS_7 0x0002 /* 7 data bits */ -#define WLS_8 0x0003 /* 8 data bits */ - /* PINTx Register Bit Definitions */ #define PIQ0 0x00000001 @@ -3225,240 +2122,6 @@ #define PIQ30 0x40000000 #define PIQ31 0x80000000 -/* PORT A Bit Definitions for the registers -PORTA, PORTA_SET, PORTA_CLEAR, -PORTA_DIR_SET, PORTA_DIR_CLEAR, PORTA_INEN, -PORTA_FER registers -*/ - -#define PA0 0x0001 -#define PA1 0x0002 -#define PA2 0x0004 -#define PA3 0x0008 -#define PA4 0x0010 -#define PA5 0x0020 -#define PA6 0x0040 -#define PA7 0x0080 -#define PA8 0x0100 -#define PA9 0x0200 -#define PA10 0x0400 -#define PA11 0x0800 -#define PA12 0x1000 -#define PA13 0x2000 -#define PA14 0x4000 -#define PA15 0x8000 - -/* PORT B Bit Definitions for the registers -PORTB, PORTB_SET, PORTB_CLEAR, -PORTB_DIR_SET, PORTB_DIR_CLEAR, PORTB_INEN, -PORTB_FER registers -*/ - -#define PB0 0x0001 -#define PB1 0x0002 -#define PB2 0x0004 -#define PB3 0x0008 -#define PB4 0x0010 -#define PB5 0x0020 -#define PB6 0x0040 -#define PB7 0x0080 -#define PB8 0x0100 -#define PB9 0x0200 -#define PB10 0x0400 -#define PB11 0x0800 -#define PB12 0x1000 -#define PB13 0x2000 -#define PB14 0x4000 - - -/* PORT C Bit Definitions for the registers -PORTC, PORTC_SET, PORTC_CLEAR, -PORTC_DIR_SET, PORTC_DIR_CLEAR, PORTC_INEN, -PORTC_FER registers -*/ - - -#define PC0 0x0001 -#define PC1 0x0002 -#define PC2 0x0004 -#define PC3 0x0008 -#define PC4 0x0010 -#define PC5 0x0020 -#define PC6 0x0040 -#define PC7 0x0080 -#define PC8 0x0100 -#define PC9 0x0200 -#define PC10 0x0400 -#define PC11 0x0800 -#define PC12 0x1000 -#define PC13 0x2000 - - -/* PORT D Bit Definitions for the registers -PORTD, PORTD_SET, PORTD_CLEAR, -PORTD_DIR_SET, PORTD_DIR_CLEAR, PORTD_INEN, -PORTD_FER registers -*/ - -#define PD0 0x0001 -#define PD1 0x0002 -#define PD2 0x0004 -#define PD3 0x0008 -#define PD4 0x0010 -#define PD5 0x0020 -#define PD6 0x0040 -#define PD7 0x0080 -#define PD8 0x0100 -#define PD9 0x0200 -#define PD10 0x0400 -#define PD11 0x0800 -#define PD12 0x1000 -#define PD13 0x2000 -#define PD14 0x4000 -#define PD15 0x8000 - -/* PORT E Bit Definitions for the registers -PORTE, PORTE_SET, PORTE_CLEAR, -PORTE_DIR_SET, PORTE_DIR_CLEAR, PORTE_INEN, -PORTE_FER registers -*/ - - -#define PE0 0x0001 -#define PE1 0x0002 -#define PE2 0x0004 -#define PE3 0x0008 -#define PE4 0x0010 -#define PE5 0x0020 -#define PE6 0x0040 -#define PE7 0x0080 -#define PE8 0x0100 -#define PE9 0x0200 -#define PE10 0x0400 -#define PE11 0x0800 -#define PE12 0x1000 -#define PE13 0x2000 -#define PE14 0x4000 -#define PE15 0x8000 - -/* PORT F Bit Definitions for the registers -PORTF, PORTF_SET, PORTF_CLEAR, -PORTF_DIR_SET, PORTF_DIR_CLEAR, PORTF_INEN, -PORTF_FER registers -*/ - - -#define PF0 0x0001 -#define PF1 0x0002 -#define PF2 0x0004 -#define PF3 0x0008 -#define PF4 0x0010 -#define PF5 0x0020 -#define PF6 0x0040 -#define PF7 0x0080 -#define PF8 0x0100 -#define PF9 0x0200 -#define PF10 0x0400 -#define PF11 0x0800 -#define PF12 0x1000 -#define PF13 0x2000 -#define PF14 0x4000 -#define PF15 0x8000 - -/* PORT G Bit Definitions for the registers -PORTG, PORTG_SET, PORTG_CLEAR, -PORTG_DIR_SET, PORTG_DIR_CLEAR, PORTG_INEN, -PORTG_FER registers -*/ - - -#define PG0 0x0001 -#define PG1 0x0002 -#define PG2 0x0004 -#define PG3 0x0008 -#define PG4 0x0010 -#define PG5 0x0020 -#define PG6 0x0040 -#define PG7 0x0080 -#define PG8 0x0100 -#define PG9 0x0200 -#define PG10 0x0400 -#define PG11 0x0800 -#define PG12 0x1000 -#define PG13 0x2000 -#define PG14 0x4000 -#define PG15 0x8000 - -/* PORT H Bit Definitions for the registers -PORTH, PORTH_SET, PORTH_CLEAR, -PORTH_DIR_SET, PORTH_DIR_CLEAR, PORTH_INEN, -PORTH_FER registers -*/ - - -#define PH0 0x0001 -#define PH1 0x0002 -#define PH2 0x0004 -#define PH3 0x0008 -#define PH4 0x0010 -#define PH5 0x0020 -#define PH6 0x0040 -#define PH7 0x0080 -#define PH8 0x0100 -#define PH9 0x0200 -#define PH10 0x0400 -#define PH11 0x0800 -#define PH12 0x1000 -#define PH13 0x2000 - - -/* PORT I Bit Definitions for the registers -PORTI, PORTI_SET, PORTI_CLEAR, -PORTI_DIR_SET, PORTI_DIR_CLEAR, PORTI_INEN, -PORTI_FER registers -*/ - - -#define PI0 0x0001 -#define PI1 0x0002 -#define PI2 0x0004 -#define PI3 0x0008 -#define PI4 0x0010 -#define PI5 0x0020 -#define PI6 0x0040 -#define PI7 0x0080 -#define PI8 0x0100 -#define PI9 0x0200 -#define PI10 0x0400 -#define PI11 0x0800 -#define PI12 0x1000 -#define PI13 0x2000 -#define PI14 0x4000 -#define PI15 0x8000 - -/* PORT J Bit Definitions for the registers -PORTJ, PORTJ_SET, PORTJ_CLEAR, -PORTJ_DIR_SET, PORTJ_DIR_CLEAR, PORTJ_INEN, -PORTJ_FER registers -*/ - - -#define PJ0 0x0001 -#define PJ1 0x0002 -#define PJ2 0x0004 -#define PJ3 0x0008 -#define PJ4 0x0010 -#define PJ5 0x0020 -#define PJ6 0x0040 -#define PJ7 0x0080 -#define PJ8 0x0100 -#define PJ9 0x0200 -#define PJ10 0x0400 -#define PJ11 0x0800 -#define PJ12 0x1000 -#define PJ13 0x2000 - - /* Port Muxing Bit Fields for PORTx_MUX Registers */ #define MUX0 0x00000003 @@ -3628,16 +2291,4 @@ PORTJ_FER registers #define B3MAP_PIH 0x06000000 /* Map Port I High to Byte 3 */ #define B3MAP_PJH 0x07000000 /* Map Port J High to Byte 3 */ - -/* for legacy compatibility */ - -#define WLS(x) (((x)-5) & 0x03) /* Word Length Select */ -#define W1LMAX_MAX W1LMAX_MIN -#define EBIU_AMCBCTL0 EBIU_AMBCTL0 -#define EBIU_AMCBCTL1 EBIU_AMBCTL1 -#define PINT0_IRQ PINT0_REQUEST -#define PINT1_IRQ PINT1_REQUEST -#define PINT2_IRQ PINT2_REQUEST -#define PINT3_IRQ PINT3_REQUEST - #endif /* _DEF_BF54X_H */ diff --git a/arch/blackfin/mach-bf548/include/mach/dma.h b/arch/blackfin/mach-bf548/include/mach/dma.h index a30d242c739..1a1091b071f 100644 --- a/arch/blackfin/mach-bf548/include/mach/dma.h +++ b/arch/blackfin/mach-bf548/include/mach/dma.h @@ -27,17 +27,37 @@ #define CH_PIXC_OVERLAY 16 #define CH_PIXC_OUTPUT 17 #define CH_SPORT2_RX 18 -#define CH_UART2_RX 18 #define CH_SPORT2_TX 19 -#define CH_UART2_TX 19 #define CH_SPORT3_RX 20 -#define CH_UART3_RX 20 #define CH_SPORT3_TX 21 -#define CH_UART3_TX 21 #define CH_SDH 22 #define CH_NFC 22 #define CH_SPI2 23 +#if defined(CONFIG_UART2_DMA_RX_ON_DMA13) +#define CH_UART2_RX 13 +#define IRQ_UART2_RX BFIN_IRQ(37) /* UART2 RX USE EPP1 (DMA13) Interrupt */ +#define CH_UART2_TX 14 +#define IRQ_UART2_TX BFIN_IRQ(38) /* UART2 RX USE EPP1 (DMA14) Interrupt */ +#else /* Default USE SPORT2's DMA Channel */ +#define CH_UART2_RX 18 +#define IRQ_UART2_RX BFIN_IRQ(33) /* UART2 RX (DMA18) Interrupt */ +#define CH_UART2_TX 19 +#define IRQ_UART2_TX BFIN_IRQ(34) /* UART2 TX (DMA19) Interrupt */ +#endif + +#if defined(CONFIG_UART3_DMA_RX_ON_DMA15) +#define CH_UART3_RX 15 +#define IRQ_UART3_RX BFIN_IRQ(64) /* UART3 RX USE PIXC IN0 (DMA15) Interrupt */ +#define CH_UART3_TX 16 +#define IRQ_UART3_TX BFIN_IRQ(65) /* UART3 TX USE PIXC IN1 (DMA16) Interrupt */ +#else /* Default USE SPORT3's DMA Channel */ +#define CH_UART3_RX 20 +#define IRQ_UART3_RX BFIN_IRQ(35) /* UART3 RX (DMA20) Interrupt */ +#define CH_UART3_TX 21 +#define IRQ_UART3_TX BFIN_IRQ(36) /* UART3 TX (DMA21) Interrupt */ +#endif + #define CH_MEM_STREAM0_DEST 24 #define CH_MEM_STREAM0_SRC 25 #define CH_MEM_STREAM1_DEST 26 diff --git a/arch/blackfin/mach-bf548/include/mach/gpio.h b/arch/blackfin/mach-bf548/include/mach/gpio.h index 850e39d193e..006da1edcf8 100644 --- a/arch/blackfin/mach-bf548/include/mach/gpio.h +++ b/arch/blackfin/mach-bf548/include/mach/gpio.h @@ -3,6 +3,10 @@ * Licensed under the GPL-2 or later. */ + +#ifndef _MACH_GPIO_H_ +#define _MACH_GPIO_H_ + #define GPIO_PA0 0 #define GPIO_PA1 1 #define GPIO_PA2 2 @@ -166,6 +170,12 @@ #define MAX_BLACKFIN_GPIOS 160 +#define BFIN_GPIO_PINT 1 +#define NR_PINT_SYS_IRQS 4 +#define NR_PINTS 160 + +#ifndef __ASSEMBLY__ + struct gpio_port_t { unsigned short port_fer; unsigned short dummy1; @@ -184,10 +194,17 @@ struct gpio_port_t { unsigned int port_mux; }; -struct gpio_port_s { - unsigned short fer; - unsigned short data; - unsigned short dir; - unsigned short inen; - unsigned int mux; -}; +#endif + +#include <mach-common/ports-a.h> +#include <mach-common/ports-b.h> +#include <mach-common/ports-c.h> +#include <mach-common/ports-d.h> +#include <mach-common/ports-e.h> +#include <mach-common/ports-f.h> +#include <mach-common/ports-g.h> +#include <mach-common/ports-h.h> +#include <mach-common/ports-i.h> +#include <mach-common/ports-j.h> + +#endif /* _MACH_GPIO_H_ */ diff --git a/arch/blackfin/mach-bf548/include/mach/irq.h b/arch/blackfin/mach-bf548/include/mach/irq.h index 106db05684a..cf7cb725cfa 100644 --- a/arch/blackfin/mach-bf548/include/mach/irq.h +++ b/arch/blackfin/mach-bf548/include/mach/irq.h @@ -7,38 +7,9 @@ #ifndef _BF548_IRQ_H_ #define _BF548_IRQ_H_ -/* - * Interrupt source definitions - Event Source Core Event Name -Core Emulation ** -Events (highest priority) EMU 0 - Reset RST 1 - NMI NMI 2 - Exception EVX 3 - Reserved -- 4 - Hardware Error IVHW 5 - Core Timer IVTMR 6 * - -..... - - Software Interrupt 1 IVG14 31 - Software Interrupt 2 -- - (lowest priority) IVG15 32 * - */ - -#define NR_PERI_INTS (32 * 3) +#include <mach-common/irq.h> -/* The ABSTRACT IRQ definitions */ -/** the first seven of the following are fixed, the rest you change if you need to **/ -#define IRQ_EMU 0 /* Emulation */ -#define IRQ_RST 1 /* reset */ -#define IRQ_NMI 2 /* Non Maskable */ -#define IRQ_EVX 3 /* Exception */ -#define IRQ_UNUSED 4 /* - unused interrupt*/ -#define IRQ_HWERR 5 /* Hardware Error */ -#define IRQ_CORETMR 6 /* Core timer */ - -#define BFIN_IRQ(x) ((x) + 7) +#define NR_PERI_INTS (3 * 32) #define IRQ_PLL_WAKEUP BFIN_IRQ(0) /* PLL Wakeup Interrupt */ #define IRQ_DMAC0_ERROR BFIN_IRQ(1) /* DMAC0 Status Interrupt */ @@ -74,13 +45,9 @@ Events (highest priority) EMU 0 #define IRQ_UART2_ERROR BFIN_IRQ(31) /* UART2 Status (Error) Interrupt */ #define IRQ_CAN0_ERROR BFIN_IRQ(32) /* CAN0 Status (Error) Interrupt */ #define IRQ_SPORT2_RX BFIN_IRQ(33) /* SPORT2 RX (DMA18) Interrupt */ -#define IRQ_UART2_RX BFIN_IRQ(33) /* UART2 RX (DMA18) Interrupt */ #define IRQ_SPORT2_TX BFIN_IRQ(34) /* SPORT2 TX (DMA19) Interrupt */ -#define IRQ_UART2_TX BFIN_IRQ(34) /* UART2 TX (DMA19) Interrupt */ #define IRQ_SPORT3_RX BFIN_IRQ(35) /* SPORT3 RX (DMA20) Interrupt */ -#define IRQ_UART3_RX BFIN_IRQ(35) /* UART3 RX (DMA20) Interrupt */ #define IRQ_SPORT3_TX BFIN_IRQ(36) /* SPORT3 TX (DMA21) Interrupt */ -#define IRQ_UART3_TX BFIN_IRQ(36) /* UART3 TX (DMA21) Interrupt */ #define IRQ_EPPI1 BFIN_IRQ(37) /* EPP1 (DMA13) Interrupt */ #define IRQ_EPPI2 BFIN_IRQ(38) /* EPP2 (DMA14) Interrupt */ #define IRQ_SPI1 BFIN_IRQ(39) /* SPI1 (DMA5) Interrupt */ @@ -315,48 +282,37 @@ Events (highest priority) EMU 0 #define IRQ_PJ14 BFIN_PJ_IRQ(14) /* N/A */ #define IRQ_PJ15 BFIN_PJ_IRQ(15) /* N/A */ -#define GPIO_IRQ_BASE IRQ_PA0 +#define GPIO_IRQ_BASE IRQ_PA0 -#define NR_IRQS (IRQ_PJ15+1) +#define NR_MACH_IRQS (IRQ_PJ15 + 1) /* For compatibility reasons with existing code */ -#define IRQ_DMAC0_ERR IRQ_DMAC0_ERROR -#define IRQ_EPPI0_ERR IRQ_EPPI0_ERROR +#define IRQ_DMAC0_ERR IRQ_DMAC0_ERROR +#define IRQ_EPPI0_ERR IRQ_EPPI0_ERROR #define IRQ_SPORT0_ERR IRQ_SPORT0_ERROR #define IRQ_SPORT1_ERR IRQ_SPORT1_ERROR -#define IRQ_SPI0_ERR IRQ_SPI0_ERROR -#define IRQ_UART0_ERR IRQ_UART0_ERROR -#define IRQ_DMAC1_ERR IRQ_DMAC1_ERROR +#define IRQ_SPI0_ERR IRQ_SPI0_ERROR +#define IRQ_UART0_ERR IRQ_UART0_ERROR +#define IRQ_DMAC1_ERR IRQ_DMAC1_ERROR #define IRQ_SPORT2_ERR IRQ_SPORT2_ERROR #define IRQ_SPORT3_ERR IRQ_SPORT3_ERROR -#define IRQ_SPI1_ERR IRQ_SPI1_ERROR -#define IRQ_SPI2_ERR IRQ_SPI2_ERROR -#define IRQ_UART1_ERR IRQ_UART1_ERROR -#define IRQ_UART2_ERR IRQ_UART2_ERROR -#define IRQ_CAN0_ERR IRQ_CAN0_ERROR -#define IRQ_MXVR_ERR IRQ_MXVR_ERROR -#define IRQ_EPPI1_ERR IRQ_EPPI1_ERROR -#define IRQ_EPPI2_ERR IRQ_EPPI2_ERROR -#define IRQ_UART3_ERR IRQ_UART3_ERROR -#define IRQ_HOST_ERR IRQ_HOST_ERROR -#define IRQ_PIXC_ERR IRQ_PIXC_ERROR -#define IRQ_NFC_ERR IRQ_NFC_ERROR -#define IRQ_ATAPI_ERR IRQ_ATAPI_ERROR -#define IRQ_CAN1_ERR IRQ_CAN1_ERROR +#define IRQ_SPI1_ERR IRQ_SPI1_ERROR +#define IRQ_SPI2_ERR IRQ_SPI2_ERROR +#define IRQ_UART1_ERR IRQ_UART1_ERROR +#define IRQ_UART2_ERR IRQ_UART2_ERROR +#define IRQ_CAN0_ERR IRQ_CAN0_ERROR +#define IRQ_MXVR_ERR IRQ_MXVR_ERROR +#define IRQ_EPPI1_ERR IRQ_EPPI1_ERROR +#define IRQ_EPPI2_ERR IRQ_EPPI2_ERROR +#define IRQ_UART3_ERR IRQ_UART3_ERROR +#define IRQ_HOST_ERR IRQ_HOST_ERROR +#define IRQ_PIXC_ERR IRQ_PIXC_ERROR +#define IRQ_NFC_ERR IRQ_NFC_ERROR +#define IRQ_ATAPI_ERR IRQ_ATAPI_ERROR +#define IRQ_CAN1_ERR IRQ_CAN1_ERROR #define IRQ_HS_DMA_ERR IRQ_HS_DMA_ERROR - -#define IVG7 7 -#define IVG8 8 -#define IVG9 9 -#define IVG10 10 -#define IVG11 11 -#define IVG12 12 -#define IVG13 13 -#define IVG14 14 -#define IVG15 15 - /* IAR0 BIT FIELDS */ #define IRQ_PLL_WAKEUP_POS 0 #define IRQ_DMAC0_ERR_POS 4 @@ -473,4 +429,26 @@ Events (highest priority) EMU 0 #define IRQ_PINT2_POS 24 #define IRQ_PINT3_POS 28 -#endif /* _BF548_IRQ_H_ */ +#ifndef __ASSEMBLY__ +#include <linux/types.h> + +/* + * gpio pint registers layout + */ +struct bfin_pint_regs { + u32 mask_set; + u32 mask_clear; + u32 request; + u32 assign; + u32 edge_set; + u32 edge_clear; + u32 invert_set; + u32 invert_clear; + u32 pinstate; + u32 latch; + u32 __pad0[2]; +}; + +#endif + +#endif diff --git a/arch/blackfin/mach-bf548/include/mach/pll.h b/arch/blackfin/mach-bf548/include/mach/pll.h new file mode 100644 index 00000000000..94cca674d83 --- /dev/null +++ b/arch/blackfin/mach-bf548/include/mach/pll.h @@ -0,0 +1 @@ +#include <mach-common/pll.h> diff --git a/arch/blackfin/mach-bf548/include/mach/portmux.h b/arch/blackfin/mach-bf548/include/mach/portmux.h index 89ad6a88636..d9f8632d7d0 100644 --- a/arch/blackfin/mach-bf548/include/mach/portmux.h +++ b/arch/blackfin/mach-bf548/include/mach/portmux.h @@ -7,8 +7,6 @@ #ifndef _MACH_PORTMUX_H_ #define _MACH_PORTMUX_H_ -#define MAX_RESOURCES MAX_BLACKFIN_GPIOS - #define P_SPORT2_TFS (P_DEFINED | P_IDENT(GPIO_PA0) | P_FUNCT(0)) #define P_SPORT2_DTSEC (P_DEFINED | P_IDENT(GPIO_PA1) | P_FUNCT(0)) #define P_SPORT2_DTPRI (P_DEFINED | P_IDENT(GPIO_PA2) | P_FUNCT(0)) @@ -131,6 +129,7 @@ #define P_KEY_COL2 (P_DEFINED | P_IDENT(GPIO_PD14) | P_FUNCT(3)) #define P_KEY_COL3 (P_DEFINED | P_IDENT(GPIO_PD15) | P_FUNCT(3)) +#define GPIO_DEFAULT_BOOT_SPI_CS GPIO_PE4 #define P_DEFAULT_BOOT_SPI_CS P_SPI0_SSEL1 #define P_SPI0_SCK (P_DEFINED | P_IDENT(GPIO_PE0) | P_FUNCT(0)) #define P_SPI0_MISO (P_DEFINED | P_IDENT(GPIO_PE1) | P_FUNCT(0)) |