diff options
Diffstat (limited to 'arch/blackfin/mach-bf533/boards/H8606.c')
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/H8606.c | 233 |
1 files changed, 110 insertions, 123 deletions
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c index 0c66bf44cfa..01300f40db1 100644 --- a/arch/blackfin/mach-bf533/boards/H8606.c +++ b/arch/blackfin/mach-bf533/boards/H8606.c @@ -1,32 +1,11 @@ /* - * File: arch/blackfin/mach-bf533/H8606.c - * Based on: arch/blackfin/mach-bf533/stamp.c - * Author: Javier Herrero <jherrero@hvsistemas.es> + * Copyright 2004-2009 Analog Devices Inc. + * 2007-2008 HV Sistemas S.L. + * Javier Herrero <jherrero@hvsistemas.es> + * 2005 National ICT Australia (NICTA) + * Aidan Williams <aidan@nicta.com.au> * - * Created: 2007 - * Description: Board Info File for the HV Sistemas H8606 board - * - * Modified: - * Copyright 2005 National ICT Australia (NICTA) - * Copyright 2004-2006 Analog Devices Inc - * Copyright 2007,2008 HV Sistemas S.L. - * - * Bugs: Enter bugs at http://blackfin.uclinux.org/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, see the file COPYING, or write - * to the Free Software Foundation, Inc., - * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + * Licensed under the GPL-2 or later. */ #include <linux/device.h> @@ -35,7 +14,7 @@ #include <linux/mtd/partitions.h> #include <linux/spi/spi.h> #include <linux/spi/flash.h> -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_ISP1362_HCD) #include <linux/usb/isp1362.h> #endif #include <linux/irq.h> @@ -50,7 +29,7 @@ */ const char bfin_board_name[] = "HV Sistemas H8606"; -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +#if IS_ENABLED(CONFIG_RTC_DRV_BFIN) static struct platform_device rtc_device = { .name = "rtc-bfin", .id = -1, @@ -60,7 +39,7 @@ static struct platform_device rtc_device = { /* * Driver needs to know address, irq and flag pin. */ - #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +#if IS_ENABLED(CONFIG_DM9000) static struct resource dm9000_resources[] = { [0] = { .start = 0x20300000, @@ -75,7 +54,8 @@ static struct resource dm9000_resources[] = { [2] = { .start = IRQ_PF10, .end = IRQ_PF10, - .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE | IRQF_SHARED | IRQF_TRIGGER_HIGH), + .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE | + IORESOURCE_IRQ_SHAREABLE), }, }; @@ -87,7 +67,15 @@ static struct platform_device dm9000_device = { }; #endif -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +#if IS_ENABLED(CONFIG_SMC91X) +#include <linux/smc91x.h> + +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, + .leda = RPC_LED_100_10, + .ledb = RPC_LED_TX_RX, +}; + static struct resource smc91x_resources[] = { { .name = "smc91x-regs", @@ -110,10 +98,13 @@ static struct platform_device smc91x_device = { .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, + .dev = { + .platform_data = &smc91x_info, + }, }; #endif -#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +#if IS_ENABLED(CONFIG_USB_NET2272) static struct resource net2272_bfin_resources[] = { { .start = 0x20300000, @@ -134,10 +125,10 @@ static struct platform_device net2272_bfin_device = { }; #endif -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) /* all SPI peripherals info goes here */ -#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) static struct mtd_partition bfin_spi_flash_partitions[] = { { .name = "bootloader (spi)", @@ -169,40 +160,13 @@ static struct flash_platform_data bfin_spi_flash_data = { /* SPI flash chip (m25p64) */ static struct bfin5xx_spi_chip spi_flash_chip_info = { .enable_dma = 0, /* use dma transfer with this chip*/ - .bits_per_word = 8, -}; -#endif - -#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) -/* SPI ADC chip */ -static struct bfin5xx_spi_chip spi_adc_chip_info = { - .ctl_reg = 0x1000, - .enable_dma = 1, /* use dma transfer with this chip*/ - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) -static struct bfin5xx_spi_chip ad1836_spi_chip_info = { - .ctl_reg = 0x1000, - .enable_dma = 0, - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_PBX) -static struct bfin5xx_spi_chip spi_si3xxx_chip_info = { - .ctl_reg = 0x1c04, - .enable_dma = 0, - .bits_per_word = 8, - .cs_change_per_word = 1, }; #endif /* Notice: for blackfin, the speed_hz is the value of register * SPI_BAUD, not the real baudrate */ static struct spi_board_info bfin_spi_board_info[] __initdata = { -#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +#if IS_ENABLED(CONFIG_MTD_M25P80) { /* the modalias must be the same as spi device driver name */ .modalias = "m25p80", /* Name of spi_driver for this device */ @@ -216,44 +180,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { }, #endif -#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) - { - .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ - .max_speed_hz = 4, /* actual baudrate is SCLK/(2xspeed_hz) */ - .bus_num = 1, /* Framework bus number */ - .chip_select = 1, /* Framework chip select. */ - .platform_data = NULL, /* No spi_driver specific config */ - .controller_data = &spi_adc_chip_info, - }, -#endif - -#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X) { - .modalias = "ad1836-spi", + .modalias = "ad183x", .max_speed_hz = 16, .bus_num = 1, - .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, - .controller_data = &ad1836_spi_chip_info, + .chip_select = 4, }, #endif -#if defined(CONFIG_PBX) - { - .modalias = "fxs-spi", - .max_speed_hz = 4, - .bus_num = 1, - .chip_select = 3, - .controller_data = &spi_si3xxx_chip_info, - }, - - { - .modalias = "fxo-spi", - .max_speed_hz = 4, - .bus_num = 1, - .chip_select = 2, - .controller_data = &spi_si3xxx_chip_info, - }, -#endif }; /* SPI (0) */ @@ -266,6 +201,11 @@ static struct resource bfin_spi0_resource[] = { [1] = { .start = CH_SPI, .end = CH_SPI, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI, + .end = IRQ_SPI, .flags = IORESOURCE_IRQ, } }; @@ -289,30 +229,58 @@ static struct platform_device bfin_spi0_device = { }; #endif /* spi master and devices */ -#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) -static struct platform_device bfin_fb_device = { - .name = "bf537-fb", -}; -#endif - -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) -static struct resource bfin_uart_resources[] = { +#if IS_ENABLED(CONFIG_SERIAL_BFIN) +#ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { { - .start = 0xFFC00400, - .end = 0xFFC004FF, + .start = BFIN_UART_THR, + .end = BFIN_UART_GCTL+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_TX, + .end = IRQ_UART0_TX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_ERROR, + .end = IRQ_UART0_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_TX, + .end = CH_UART0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static unsigned short bfin_uart0_peripherals[] = { + P_UART0_TX, P_UART0_RX, 0 }; -static struct platform_device bfin_uart_device = { +static struct platform_device bfin_uart0_device = { .name = "bfin-uart", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_uart_resources), - .resource = bfin_uart_resources, + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, + .dev = { + .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ + }, }; #endif +#endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 static struct resource bfin_sir0_resources[] = { { @@ -341,7 +309,7 @@ static struct platform_device bfin_sir0_device = { #endif #endif -#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE) +#if IS_ENABLED(CONFIG_SERIAL_8250) #include <linux/serial_8250.h> #include <linux/serial.h> @@ -357,6 +325,7 @@ static struct plat_serial8250_port serial8250_platform_data [] = { .membase = (void *)0x20200000, .mapbase = 0x20200000, .irq = IRQ_PF8, + .irqflags = IRQF_TRIGGER_HIGH, .flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE, .iotype = UPIO_MEM, .regshift = 1, @@ -365,6 +334,7 @@ static struct plat_serial8250_port serial8250_platform_data [] = { .membase = (void *)0x20200010, .mapbase = 0x20200010, .irq = IRQ_PF8, + .irqflags = IRQF_TRIGGER_HIGH, .flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE, .iotype = UPIO_MEM, .regshift = 1, @@ -383,7 +353,7 @@ static struct platform_device serial8250_device = { #endif -#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_OPENCORES) /* * Configuration for one OpenCores keyboard controller in FPGA at address 0x20200030, @@ -412,41 +382,43 @@ static struct platform_device opencores_kbd_device = { #endif static struct platform_device *h8606_devices[] __initdata = { -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +#if IS_ENABLED(CONFIG_RTC_DRV_BFIN) &rtc_device, #endif -#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +#if IS_ENABLED(CONFIG_DM9000) &dm9000_device, #endif -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +#if IS_ENABLED(CONFIG_SMC91X) &smc91x_device, #endif -#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +#if IS_ENABLED(CONFIG_USB_NET2272) &net2272_bfin_device, #endif -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) &bfin_spi0_device, #endif -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) - &bfin_uart_device, +#if IS_ENABLED(CONFIG_SERIAL_BFIN) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif #endif -#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE) +#if IS_ENABLED(CONFIG_SERIAL_8250) &serial8250_device, #endif -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#if IS_ENABLED(CONFIG_BFIN_SIR) #ifdef CONFIG_BFIN_SIR0 &bfin_sir0_device, #endif #endif -#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_OPENCORES) &opencores_kbd_device, #endif }; @@ -456,10 +428,25 @@ static int __init H8606_init(void) printk(KERN_INFO "HV Sistemas H8606 board support by http://www.hvsistemas.com\n"); printk(KERN_INFO "%s(): registering device resources\n", __func__); platform_add_devices(h8606_devices, ARRAY_SIZE(h8606_devices)); -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +#if IS_ENABLED(CONFIG_SPI_BFIN5XX) spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); #endif return 0; } arch_initcall(H8606_init); + +static struct platform_device *H8606_early_devices[] __initdata = { +#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#endif +}; + +void __init native_machine_early_platform_add_devices(void) +{ + printk(KERN_INFO "register early platform devices\n"); + early_platform_add_devices(H8606_early_devices, + ARRAY_SIZE(H8606_early_devices)); +} |