diff options
Diffstat (limited to 'arch/avr32/boards/atstk1000')
| -rw-r--r-- | arch/avr32/boards/atstk1000/Kconfig | 62 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/Makefile | 3 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1000.h | 4 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 265 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1003.c | 162 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1004.c | 164 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/flash.c | 2 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/setup.c | 68 |
8 files changed, 616 insertions, 114 deletions
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig index 718578f6406..8dc48214f0b 100644 --- a/arch/avr32/boards/atstk1000/Kconfig +++ b/arch/avr32/boards/atstk1000/Kconfig @@ -1,34 +1,57 @@ # STK1000 customization -if BOARD_ATSTK1002 +if BOARD_ATSTK1000 -config BOARD_ATSTK1002_CUSTOM - bool "Non-default STK-1002 jumper settings" +choice + prompt "ATSTK1000 CPU daughterboard type" + default BOARD_ATSTK1002 + +config BOARD_ATSTK1002 + bool "ATSTK1002" + select CPU_AT32AP7000 + +config BOARD_ATSTK1003 + bool "ATSTK1003" + select CPU_AT32AP7001 + +config BOARD_ATSTK1004 + bool "ATSTK1004" + select CPU_AT32AP7002 + +config BOARD_ATSTK1006 + bool "ATSTK1006" + select CPU_AT32AP7000 + +endchoice + + +config BOARD_ATSTK100X_CUSTOM + bool "Non-default STK1002/STK1003/STK1004 jumper settings" help You will normally leave the jumpers on the CPU card at their default settings. If you need to use certain peripherals, you will need to change some of those jumpers. -if BOARD_ATSTK1002_CUSTOM +if BOARD_ATSTK100X_CUSTOM -config BOARD_ATSTK1002_SW1_CUSTOM +config BOARD_ATSTK100X_SW1_CUSTOM bool "SW1: use SSC1 (not SPI0)" help This also prevents using the external DAC as an audio interface, and means you can't initialize the on-board QVGA display. -config BOARD_ATSTK1002_SW2_CUSTOM +config BOARD_ATSTK100X_SW2_CUSTOM bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)" help If you change this you'll want an updated boot loader putting the console on UART-C not UART-A. -config BOARD_ATSTK1002_SW3_CUSTOM +config BOARD_ATSTK100X_SW3_CUSTOM bool "SW3: use TIMER1 (not SSC0 and GCLK)" help This also prevents using the external DAC as an audio interface. -config BOARD_ATSTK1002_SW4_CUSTOM +config BOARD_ATSTK100X_SW4_CUSTOM bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)" help To use the camera interface you'll need a custom card (on the @@ -36,27 +59,29 @@ config BOARD_ATSTK1002_SW4_CUSTOM config BOARD_ATSTK1002_SW5_CUSTOM bool "SW5: use MACB1 (not LCDC)" + depends on BOARD_ATSTK1002 config BOARD_ATSTK1002_SW6_CUSTOM bool "SW6: more GPIOs (not MACB0)" + depends on BOARD_ATSTK1002 endif # custom -config BOARD_ATSTK1002_SPI1 +config BOARD_ATSTK100X_SPI1 bool "Configure SPI1 controller" - depends on !BOARD_ATSTK1002_SW4_CUSTOM + depends on !BOARD_ATSTK100X_SW4_CUSTOM help All the signals for the second SPI controller are available on GPIO lines and accessed through the J1 jumper block. Say "y" here to configure that SPI controller. -config BOARD_ATSTK1002_J2_LED +config BOARD_ATSTK1000_J2_LED bool - default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB + default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB choice prompt "LEDs connected to J2:" - depends on LEDS_GPIO && !BOARD_ATSTK1002_SW4_CUSTOM + depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM optional help Select this if you have jumpered the J2 jumper block to the @@ -64,16 +89,21 @@ choice IDC cable. A default "heartbeat" trigger is provided, but you can of course override this. -config BOARD_ATSTK1002_J2_LED8 +config BOARD_ATSTK1000_J2_LED8 bool "LED0..LED7" help Select this if J2 is jumpered to LED0..LED7 amber leds. -config BOARD_ATSTK1002_J2_RGB +config BOARD_ATSTK1000_J2_RGB bool "RGB leds" help Select this if J2 is jumpered to the RGB leds. endchoice -endif # stk 1002 +config BOARD_ATSTK1000_EXTDAC + bool + depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM + default y + +endif # stk 1000 diff --git a/arch/avr32/boards/atstk1000/Makefile b/arch/avr32/boards/atstk1000/Makefile index 8e0992201bb..edecee03742 100644 --- a/arch/avr32/boards/atstk1000/Makefile +++ b/arch/avr32/boards/atstk1000/Makefile @@ -1,2 +1,5 @@ obj-y += setup.o flash.o obj-$(CONFIG_BOARD_ATSTK1002) += atstk1002.o +obj-$(CONFIG_BOARD_ATSTK1003) += atstk1003.o +obj-$(CONFIG_BOARD_ATSTK1004) += atstk1004.o +obj-$(CONFIG_BOARD_ATSTK1006) += atstk1002.o diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h index 9a49ed036b7..653cc09e536 100644 --- a/arch/avr32/boards/atstk1000/atstk1000.h +++ b/arch/avr32/boards/atstk1000/atstk1000.h @@ -10,6 +10,8 @@ #ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H #define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H -extern struct atmel_lcdfb_info atstk1000_lcdc_data; +extern struct atmel_lcdfb_pdata atstk1000_lcdc_data; + +void atstk1000_setup_j2_leds(void); #endif /* __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H */ diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index 6b9e466104a..6c80aba7bf9 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -1,7 +1,7 @@ /* - * ATSTK1002 daughterboard-specific init code + * ATSTK1002/ATSTK1006 daughterboard-specific init code * - * Copyright (C) 2005-2006 Atmel Corporation + * Copyright (C) 2005-2007 Atmel Corporation * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -11,30 +11,102 @@ #include <linux/etherdevice.h> #include <linux/init.h> #include <linux/kernel.h> -#include <linux/leds.h> #include <linux/platform_device.h> #include <linux/string.h> #include <linux/types.h> #include <linux/spi/spi.h> +#include <linux/spi/at73c213.h> +#include <linux/atmel-mci.h> #include <video/atmel_lcdc.h> #include <asm/io.h> #include <asm/setup.h> -#include <asm/arch/at32ap7000.h> -#include <asm/arch/board.h> -#include <asm/arch/init.h> -#include <asm/arch/portmux.h> + +#include <mach/at32ap700x.h> +#include <mach/board.h> +#include <mach/init.h> +#include <mach/portmux.h> #include "atstk1000.h" +/* Oscillator frequencies. These are board specific */ +unsigned long at32_board_osc_rates[3] = { + [0] = 32768, /* 32.768 kHz on RTC osc */ + [1] = 20000000, /* 20 MHz on osc0 */ + [2] = 12000000, /* 12 MHz on osc1 */ +}; + +/* + * The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both + * have the AT32AP7000 chip on board; the difference is that the + * STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on + * the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has + * none.) + * + * The RAM difference is handled by the boot loader, so the only + * difference we end up handling here is the NAND flash. + */ +#ifdef CONFIG_BOARD_ATSTK1006 +#include <linux/mtd/partitions.h> +#include <mach/smc.h> + +static struct smc_timing nand_timing __initdata = { + .ncs_read_setup = 0, + .nrd_setup = 10, + .ncs_write_setup = 0, + .nwe_setup = 10, + + .ncs_read_pulse = 30, + .nrd_pulse = 15, + .ncs_write_pulse = 30, + .nwe_pulse = 15, + + .read_cycle = 30, + .write_cycle = 30, + + .ncs_read_recover = 0, + .nrd_recover = 15, + .ncs_write_recover = 0, + /* WE# high -> RE# low min 60 ns */ + .nwe_recover = 50, +}; + +static struct smc_config nand_config __initdata = { + .bus_width = 1, + .nrd_controlled = 1, + .nwe_controlled = 1, + .nwait_mode = 0, + .byte_write = 0, + .tdf_cycles = 2, + .tdf_mode = 0, +}; + +static struct mtd_partition nand_partitions[] = { + { + .name = "main", + .offset = 0x00000000, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct atmel_nand_data atstk1006_nand_data __initdata = { + .cle = 21, + .ale = 22, + .rdy_pin = GPIO_PIN_PB(30), + .enable_pin = GPIO_PIN_PB(29), + .ecc_mode = NAND_ECC_SOFT, + .parts = nand_partitions, + .num_parts = ARRAY_SIZE(nand_partitions), +}; +#endif struct eth_addr { u8 addr[6]; }; static struct eth_addr __initdata hw_addr[2]; -static struct eth_platform_data __initdata eth_data[2] = { +static struct macb_platform_data __initdata eth_data[2] = { { /* * The MDIO pullups on STK1000 are a bit too weak for @@ -48,8 +120,25 @@ static struct eth_platform_data __initdata eth_data[2] = { }, }; -#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC +static struct at73c213_board_info at73c213_data = { + .ssc_id = 0, + .shortname = "AVR32 STK1000 external DAC", +}; +#endif + +#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM static struct spi_board_info spi0_board_info[] __initdata = { +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC + { + /* AT73C213 */ + .modalias = "at73c213", + .max_speed_hz = 200000, + .chip_select = 0, + .mode = SPI_MODE_1, + .platform_data = &at73c213_data, + }, +#endif { /* QVGA display */ .modalias = "ltv350qv", @@ -60,7 +149,7 @@ static struct spi_board_info spi0_board_info[] __initdata = { }; #endif -#ifdef CONFIG_BOARD_ATSTK1002_SPI1 +#ifdef CONFIG_BOARD_ATSTK100X_SPI1 static struct spi_board_info spi1_board_info[] __initdata = { { /* patch in custom entries here */ } }; @@ -110,7 +199,7 @@ static void __init set_hw_addr(struct platform_device *pdev) */ regs = (void __iomem __force *)res->start; pclk = clk_get(&pdev->dev, "pclk"); - if (!pclk) + if (IS_ERR(pclk)) return; clk_enable(pclk); @@ -121,105 +210,88 @@ static void __init set_hw_addr(struct platform_device *pdev) clk_put(pclk); } -#ifdef CONFIG_BOARD_ATSTK1002_J2_LED - -static struct gpio_led stk_j2_led[] = { -#ifdef CONFIG_BOARD_ATSTK1002_J2_LED8 -#define LEDSTRING "J2 jumpered to LED8" - { .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), }, - { .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), }, - { .name = "led2:amber", .gpio = GPIO_PIN_PB(10), }, - { .name = "led3:amber", .gpio = GPIO_PIN_PB(13), }, - { .name = "led4:amber", .gpio = GPIO_PIN_PB(14), }, - { .name = "led5:amber", .gpio = GPIO_PIN_PB(15), }, - { .name = "led6:amber", .gpio = GPIO_PIN_PB(16), }, - { .name = "led7:amber", .gpio = GPIO_PIN_PB(30), - .default_trigger = "heartbeat", }, -#else /* RGB */ -#define LEDSTRING "J2 jumpered to RGB LEDs" - { .name = "r1:red", .gpio = GPIO_PIN_PB( 8), }, - { .name = "g1:green", .gpio = GPIO_PIN_PB(10), }, - { .name = "b1:blue", .gpio = GPIO_PIN_PB(14), }, - - { .name = "r2:red", .gpio = GPIO_PIN_PB( 9), - .default_trigger = "heartbeat", }, - { .name = "g2:green", .gpio = GPIO_PIN_PB(13), }, - { .name = "b2:blue", .gpio = GPIO_PIN_PB(15), - .default_trigger = "heartbeat", }, - /* PB16, PB30 unused */ -#endif -}; - -static struct gpio_led_platform_data stk_j2_led_data = { - .num_leds = ARRAY_SIZE(stk_j2_led), - .leds = stk_j2_led, -}; - -static struct platform_device stk_j2_led_dev = { - .name = "leds-gpio", - .id = 2, /* gpio block J2 */ - .dev = { - .platform_data = &stk_j2_led_data, - }, -}; - -static void setup_j2_leds(void) +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC +static void __init atstk1002_setup_extdac(void) { - unsigned i; - - for (i = 0; i < ARRAY_SIZE(stk_j2_led); i++) - at32_select_gpio(stk_j2_led[i].gpio, AT32_GPIOF_OUTPUT); - - printk("STK1002: " LEDSTRING "\n"); - platform_device_register(&stk_j2_led_dev); + struct clk *gclk; + struct clk *pll; + + gclk = clk_get(NULL, "gclk0"); + if (IS_ERR(gclk)) + goto err_gclk; + pll = clk_get(NULL, "pll0"); + if (IS_ERR(pll)) + goto err_pll; + + if (clk_set_parent(gclk, pll)) { + pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n"); + goto err_set_clk; + } + + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); + at73c213_data.dac_clk = gclk; + +err_set_clk: + clk_put(pll); +err_pll: + clk_put(gclk); +err_gclk: + return; } - #else -static void setup_j2_leds(void) +static void __init atstk1002_setup_extdac(void) { + } -#endif +#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */ void __init setup_board(void) { -#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM - at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */ +#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */ #else - at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */ + at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */ #endif /* USART 2/unused: expansion connector */ - at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */ + at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */ at32_setup_serial_console(0); } +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + +/* MMC card detect requires MACB0 *NOT* be used */ +#ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM + .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ + .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ +#else + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, +#endif /* SW6 for sd{cd,wp} routing */ + }, +}; + +#endif /* SW2 for MMC signal routing */ + static int __init atstk1002_init(void) { /* * ATSTK1000 uses 32-bit SDRAM interface. Reserve the * SDRAM-specific pins so that nobody messes with them. */ - at32_reserve_pin(GPIO_PIN_PE(0)); /* DATA[16] */ - at32_reserve_pin(GPIO_PIN_PE(1)); /* DATA[17] */ - at32_reserve_pin(GPIO_PIN_PE(2)); /* DATA[18] */ - at32_reserve_pin(GPIO_PIN_PE(3)); /* DATA[19] */ - at32_reserve_pin(GPIO_PIN_PE(4)); /* DATA[20] */ - at32_reserve_pin(GPIO_PIN_PE(5)); /* DATA[21] */ - at32_reserve_pin(GPIO_PIN_PE(6)); /* DATA[22] */ - at32_reserve_pin(GPIO_PIN_PE(7)); /* DATA[23] */ - at32_reserve_pin(GPIO_PIN_PE(8)); /* DATA[24] */ - at32_reserve_pin(GPIO_PIN_PE(9)); /* DATA[25] */ - at32_reserve_pin(GPIO_PIN_PE(10)); /* DATA[26] */ - at32_reserve_pin(GPIO_PIN_PE(11)); /* DATA[27] */ - at32_reserve_pin(GPIO_PIN_PE(12)); /* DATA[28] */ - at32_reserve_pin(GPIO_PIN_PE(13)); /* DATA[29] */ - at32_reserve_pin(GPIO_PIN_PE(14)); /* DATA[30] */ - at32_reserve_pin(GPIO_PIN_PE(15)); /* DATA[31] */ - at32_reserve_pin(GPIO_PIN_PE(26)); /* SDCS */ - - at32_add_system_devices(); - -#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM + at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL); + +#ifdef CONFIG_BOARD_ATSTK1006 + smc_set_timing(&nand_config, &nand_timing); + smc_set_configuration(3, &nand_config); + at32_add_device_nand(0, &atstk1006_nand_data); +#endif + +#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM at32_add_device_usart(1); #else at32_add_device_usart(0); @@ -229,24 +301,29 @@ static int __init atstk1002_init(void) #ifndef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM set_hw_addr(at32_add_device_eth(0, ð_data[0])); #endif -#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM +#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); #endif -#ifdef CONFIG_BOARD_ATSTK1002_SPI1 +#ifdef CONFIG_BOARD_ATSTK100X_SPI1 at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_mci(0, &mci0_data); +#endif #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM set_hw_addr(at32_add_device_eth(1, ð_data[1])); #else at32_add_device_lcdc(0, &atstk1000_lcdc_data, - fbmem_start, fbmem_size); + fbmem_start, fbmem_size, + ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL); #endif at32_add_device_usba(0, NULL); -#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM +#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM at32_add_device_ssc(0, ATMEL_SSC_TX); #endif - setup_j2_leds(); + atstk1000_setup_j2_leds(); + atstk1002_setup_extdac(); return 0; } diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c new file mode 100644 index 00000000000..ff7e2329882 --- /dev/null +++ b/arch/avr32/boards/atstk1000/atstk1003.c @@ -0,0 +1,162 @@ +/* + * ATSTK1003 daughterboard-specific init code + * + * Copyright (C) 2007 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/string.h> +#include <linux/types.h> + +#include <linux/spi/at73c213.h> +#include <linux/spi/spi.h> +#include <linux/atmel-mci.h> + +#include <asm/setup.h> + +#include <mach/at32ap700x.h> +#include <mach/board.h> +#include <mach/init.h> +#include <mach/portmux.h> + +#include "atstk1000.h" + +/* Oscillator frequencies. These are board specific */ +unsigned long at32_board_osc_rates[3] = { + [0] = 32768, /* 32.768 kHz on RTC osc */ + [1] = 20000000, /* 20 MHz on osc0 */ + [2] = 12000000, /* 12 MHz on osc1 */ +}; + +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC +static struct at73c213_board_info at73c213_data = { + .ssc_id = 0, + .shortname = "AVR32 STK1000 external DAC", +}; +#endif + +#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM +static struct spi_board_info spi0_board_info[] __initdata = { +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC + { + /* AT73C213 */ + .modalias = "at73c213", + .max_speed_hz = 200000, + .chip_select = 0, + .mode = SPI_MODE_1, + .platform_data = &at73c213_data, + }, +#endif + /* + * We can control the LTV350QV LCD panel, but it isn't much + * point since we don't have an LCD controller... + */ +}; +#endif + +#ifdef CONFIG_BOARD_ATSTK100X_SPI1 +static struct spi_board_info spi1_board_info[] __initdata = { { + /* patch in custom entries here */ +} }; +#endif + +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, + }, +}; +#endif + +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC +static void __init atstk1003_setup_extdac(void) +{ + struct clk *gclk; + struct clk *pll; + + gclk = clk_get(NULL, "gclk0"); + if (IS_ERR(gclk)) + goto err_gclk; + pll = clk_get(NULL, "pll0"); + if (IS_ERR(pll)) + goto err_pll; + + if (clk_set_parent(gclk, pll)) { + pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n"); + goto err_set_clk; + } + + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); + at73c213_data.dac_clk = gclk; + +err_set_clk: + clk_put(pll); +err_pll: + clk_put(gclk); +err_gclk: + return; +} +#else +static void __init atstk1003_setup_extdac(void) +{ + +} +#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */ + +void __init setup_board(void) +{ +#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */ +#else + at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */ +#endif + /* USART 2/unused: expansion connector */ + at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */ + + at32_setup_serial_console(0); +} + +static int __init atstk1003_init(void) +{ + /* + * ATSTK1000 uses 32-bit SDRAM interface. Reserve the + * SDRAM-specific pins so that nobody messes with them. + */ + at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL); + +#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_usart(1); +#else + at32_add_device_usart(0); +#endif + at32_add_device_usart(2); + +#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM + at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); +#endif +#ifdef CONFIG_BOARD_ATSTK100X_SPI1 + at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); +#endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_mci(0, &mci0_data); +#endif + at32_add_device_usba(0, NULL); +#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM + at32_add_device_ssc(0, ATMEL_SSC_TX); +#endif + + atstk1000_setup_j2_leds(); + atstk1003_setup_extdac(); + + return 0; +} +postcore_initcall(atstk1003_init); diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c new file mode 100644 index 00000000000..69a9f0f08c6 --- /dev/null +++ b/arch/avr32/boards/atstk1000/atstk1004.c @@ -0,0 +1,164 @@ +/* + * ATSTK1003 daughterboard-specific init code + * + * Copyright (C) 2007 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/string.h> +#include <linux/types.h> + +#include <linux/spi/at73c213.h> +#include <linux/spi/spi.h> +#include <linux/atmel-mci.h> + +#include <video/atmel_lcdc.h> + +#include <asm/setup.h> + +#include <mach/at32ap700x.h> +#include <mach/board.h> +#include <mach/init.h> +#include <mach/portmux.h> + +#include "atstk1000.h" + +/* Oscillator frequencies. These are board specific */ +unsigned long at32_board_osc_rates[3] = { + [0] = 32768, /* 32.768 kHz on RTC osc */ + [1] = 20000000, /* 20 MHz on osc0 */ + [2] = 12000000, /* 12 MHz on osc1 */ +}; + +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC +static struct at73c213_board_info at73c213_data = { + .ssc_id = 0, + .shortname = "AVR32 STK1000 external DAC", +}; +#endif + +#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM +static struct spi_board_info spi0_board_info[] __initdata = { +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC + { + /* AT73C213 */ + .modalias = "at73c213", + .max_speed_hz = 200000, + .chip_select = 0, + .mode = SPI_MODE_1, + .platform_data = &at73c213_data, + }, +#endif + { + /* QVGA display */ + .modalias = "ltv350qv", + .max_speed_hz = 16000000, + .chip_select = 1, + .mode = SPI_MODE_3, + }, +}; +#endif + +#ifdef CONFIG_BOARD_ATSTK100X_SPI1 +static struct spi_board_info spi1_board_info[] __initdata = { { + /* patch in custom entries here */ +} }; +#endif + +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, + }, +}; +#endif + +#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC +static void __init atstk1004_setup_extdac(void) +{ + struct clk *gclk; + struct clk *pll; + + gclk = clk_get(NULL, "gclk0"); + if (IS_ERR(gclk)) + goto err_gclk; + pll = clk_get(NULL, "pll0"); + if (IS_ERR(pll)) + goto err_pll; + + if (clk_set_parent(gclk, pll)) { + pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n"); + goto err_set_clk; + } + + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); + at73c213_data.dac_clk = gclk; + +err_set_clk: + clk_put(pll); +err_pll: + clk_put(gclk); +err_gclk: + return; +} +#else +static void __init atstk1004_setup_extdac(void) +{ + +} +#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */ + +void __init setup_board(void) +{ +#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */ +#else + at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */ +#endif + /* USART 2/unused: expansion connector */ + at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */ + + at32_setup_serial_console(0); +} + +static int __init atstk1004_init(void) +{ +#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_usart(1); +#else + at32_add_device_usart(0); +#endif + at32_add_device_usart(2); + +#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM + at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); +#endif +#ifdef CONFIG_BOARD_ATSTK100X_SPI1 + at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); +#endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_mci(0, &mci0_data); +#endif + at32_add_device_lcdc(0, &atstk1000_lcdc_data, + fbmem_start, fbmem_size, + ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL); + at32_add_device_usba(0, NULL); +#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM + at32_add_device_ssc(0, ATMEL_SSC_TX); +#endif + + atstk1000_setup_j2_leds(); + atstk1004_setup_extdac(); + + return 0; +} +postcore_initcall(atstk1004_init); diff --git a/arch/avr32/boards/atstk1000/flash.c b/arch/avr32/boards/atstk1000/flash.c index 3d0a102ad45..6e4d561977f 100644 --- a/arch/avr32/boards/atstk1000/flash.c +++ b/arch/avr32/boards/atstk1000/flash.c @@ -13,7 +13,7 @@ #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> -#include <asm/arch/smc.h> +#include <mach/smc.h> static struct smc_timing flash_timing __initdata = { .ncs_read_setup = 0, diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c index c9af409ada9..b6b88f5e0b4 100644 --- a/arch/avr32/boards/atstk1000/setup.c +++ b/arch/avr32/boards/atstk1000/setup.c @@ -10,13 +10,17 @@ #include <linux/bootmem.h> #include <linux/fb.h> #include <linux/init.h> +#include <linux/platform_device.h> #include <linux/types.h> #include <linux/linkage.h> #include <video/atmel_lcdc.h> #include <asm/setup.h> -#include <asm/arch/board.h> + +#include <mach/at32ap700x.h> +#include <mach/board.h> +#include <mach/portmux.h> #include "atstk1000.h" @@ -51,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = { .dclkmax = 30000000, }; -struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = { +struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = { .default_bpp = 24, .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN, .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT @@ -61,3 +65,63 @@ struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = { .default_monspecs = &atstk1000_default_monspecs, .guard_time = 2, }; + +#ifdef CONFIG_BOARD_ATSTK1000_J2_LED +#include <linux/leds.h> + +static struct gpio_led stk1000_j2_led[] = { +#ifdef CONFIG_BOARD_ATSTK1000_J2_LED8 +#define LEDSTRING "J2 jumpered to LED8" + { .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), }, + { .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), }, + { .name = "led2:amber", .gpio = GPIO_PIN_PB(10), }, + { .name = "led3:amber", .gpio = GPIO_PIN_PB(13), }, + { .name = "led4:amber", .gpio = GPIO_PIN_PB(14), }, + { .name = "led5:amber", .gpio = GPIO_PIN_PB(15), }, + { .name = "led6:amber", .gpio = GPIO_PIN_PB(16), }, + { .name = "led7:amber", .gpio = GPIO_PIN_PB(30), + .default_trigger = "heartbeat", }, +#else /* RGB */ +#define LEDSTRING "J2 jumpered to RGB LEDs" + { .name = "r1:red", .gpio = GPIO_PIN_PB( 8), }, + { .name = "g1:green", .gpio = GPIO_PIN_PB(10), }, + { .name = "b1:blue", .gpio = GPIO_PIN_PB(14), }, + + { .name = "r2:red", .gpio = GPIO_PIN_PB( 9), + .default_trigger = "heartbeat", }, + { .name = "g2:green", .gpio = GPIO_PIN_PB(13), }, + { .name = "b2:blue", .gpio = GPIO_PIN_PB(15), + .default_trigger = "heartbeat", }, + /* PB16, PB30 unused */ +#endif +}; + +static struct gpio_led_platform_data stk1000_j2_led_data = { + .num_leds = ARRAY_SIZE(stk1000_j2_led), + .leds = stk1000_j2_led, +}; + +static struct platform_device stk1000_j2_led_dev = { + .name = "leds-gpio", + .id = 2, /* gpio block J2 */ + .dev = { + .platform_data = &stk1000_j2_led_data, + }, +}; + +void __init atstk1000_setup_j2_leds(void) +{ + unsigned i; + + for (i = 0; i < ARRAY_SIZE(stk1000_j2_led); i++) + at32_select_gpio(stk1000_j2_led[i].gpio, AT32_GPIOF_OUTPUT); + + printk("STK1000: " LEDSTRING "\n"); + platform_device_register(&stk1000_j2_led_dev); +} +#else /* CONFIG_BOARD_ATSTK1000_J2_LED */ +void __init atstk1000_setup_j2_leds(void) +{ + +} +#endif /* CONFIG_BOARD_ATSTK1000_J2_LED */ |