1 files changed, 0 insertions, 158 deletions
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
deleted file mode 100644
index aa5afbcc90f..00000000000
--- a/arch/arm/mach-ux500/board-mop500.c
+++ /dev/null
@@ -1,158 +0,0 @@
-/*
- * Copyright (C) 2008-2009 ST-Ericsson
- *
- * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2, as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/pl022.h>
-#include <linux/spi/spi.h>
-
-#include <asm/localtimer.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <plat/mtu.h>
-
-#include <mach/hardware.h>
-#include <mach/setup.h>
-
-#define __MEM_4K_RESOURCE(x) \
-	.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
-
-/* These are active devices on this board */
-static struct amba_device uart0_device = {
-	.dev = { .init_name = "uart0" },
-	__MEM_4K_RESOURCE(U8500_UART0_BASE),
-	.irq = {IRQ_UART0, NO_IRQ},
-};
-
-static struct amba_device uart1_device = {
-	.dev = { .init_name = "uart1" },
-	__MEM_4K_RESOURCE(U8500_UART1_BASE),
-	.irq = {IRQ_UART1, NO_IRQ},
-};
-
-static struct amba_device uart2_device = {
-	.dev = { .init_name = "uart2" },
-	__MEM_4K_RESOURCE(U8500_UART2_BASE),
-	.irq = {IRQ_UART2, NO_IRQ},
-};
-
-static void ab4500_spi_cs_control(u32 command)
-{
-	/* set the FRM signal, which is CS  - TODO */
-}
-
-struct pl022_config_chip ab4500_chip_info = {
-	.lbm = LOOPBACK_DISABLED,
-	.com_mode = INTERRUPT_TRANSFER,
-	.iface = SSP_INTERFACE_MOTOROLA_SPI,
-	/* we can act as master only */
-	.hierarchy = SSP_MASTER,
-	.slave_tx_disable = 0,
-	.endian_rx = SSP_RX_MSB,
-	.endian_tx = SSP_TX_MSB,
-	.data_size = SSP_DATA_BITS_24,
-	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
-	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.clk_phase = SSP_CLK_SECOND_EDGE,
-	.clk_pol = SSP_CLK_POL_IDLE_HIGH,
-	.cs_control = ab4500_spi_cs_control,
-};
-
-static struct spi_board_info u8500_spi_devices[] = {
-	{
-		.modalias = "ab4500",
-		.controller_data = &ab4500_chip_info,
-		.max_speed_hz = 12000000,
-		.bus_num = 0,
-		.chip_select = 0,
-		.mode = SPI_MODE_0,
-		.irq = IRQ_AB4500,
-	},
-};
-
-static struct pl022_ssp_controller ssp0_platform_data = {
-	.bus_id = 0,
-	/* pl022 not yet supports dma */
-	.enable_dma = 0,
-	/* on this platform, gpio 31,142,144,214 &
-	 * 224 are connected as chip selects
-	 */
-	.num_chipselect = 5,
-};
-
-static struct amba_device pl022_device = {
-	.dev = {
-		.coherent_dma_mask = ~0,
-		.init_name = "pl022",
-		.platform_data = &ssp0_platform_data,
-	},
-	.res = {
-		.start = U8500_SSP0_BASE,
-		.end   = U8500_SSP0_BASE + SZ_4K - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	.irq = {IRQ_SSP0, NO_IRQ },
-	/* ST-Ericsson modified id */
-	.periphid = SSP_PER_ID,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
-	&uart0_device,
-	&uart1_device,
-	&uart2_device,
-	&pl022_device,
-};
-
-static void __init u8500_timer_init(void)
-{
-#ifdef CONFIG_LOCAL_TIMERS
-	/* Setup the local timer base */
-	twd_base = __io_address(U8500_TWD_BASE);
-#endif
-	/* Setup the MTU base */
-	mtu_base = __io_address(U8500_MTU0_BASE);
-
-	nmdk_timer_init();
-}
-
-static struct sys_timer u8500_timer = {
-	.init	= u8500_timer_init,
-};
-
-static void __init u8500_init_machine(void)
-{
-	int i;
-
-	/* Register the active AMBA devices on this board */
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
-		amba_device_register(amba_devs[i], &iomem_resource);
-
-	spi_register_board_info(u8500_spi_devices,
-			ARRAY_SIZE(u8500_spi_devices));
-
-	u8500_init_devices();
-}
-
-MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
-	/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
-	.phys_io	= U8500_UART2_BASE,
-	.io_pg_offst	= (IO_ADDRESS(U8500_UART2_BASE) >> 18) & 0xfffc,
-	.boot_params	= 0x100,
-	.map_io		= u8500_map_io,
-	.init_irq	= u8500_init_irq,
-	/* we re-use nomadik timer here */
-	.timer		= &u8500_timer,
-	.init_machine	= u8500_init_machine,
-MACHINE_END