diff options
Diffstat (limited to 'arch/arm/mach-ux500/board-mop500.c')
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500.c | 327 |
1 files changed, 0 insertions, 327 deletions
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c deleted file mode 100644 index cac83a69488..00000000000 --- a/arch/arm/mach-ux500/board-mop500.c +++ /dev/null @@ -1,327 +0,0 @@ -/* - * Copyright (C) 2008-2009 ST-Ericsson - * - * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2, as - * published by the Free Software Foundation. - * - */ -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/platform_device.h> -#include <linux/io.h> -#include <linux/gpio.h> -#include <linux/amba/bus.h> -#include <linux/amba/pl022.h> -#include <linux/spi/spi.h> -#include <linux/mfd/ab8500.h> -#include <linux/input/matrix_keypad.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> - -#include <plat/pincfg.h> -#include <plat/i2c.h> -#include <plat/ske.h> - -#include <mach/hardware.h> -#include <mach/setup.h> -#include <mach/devices.h> -#include <mach/irqs.h> - -#include "pins-db8500.h" -#include "board-mop500.h" - -static pin_cfg_t mop500_pins[] = { - /* SSP0 */ - GPIO143_SSP0_CLK, - GPIO144_SSP0_FRM, - GPIO145_SSP0_RXD, - GPIO146_SSP0_TXD, - - /* I2C */ - GPIO147_I2C0_SCL, - GPIO148_I2C0_SDA, - GPIO16_I2C1_SCL, - GPIO17_I2C1_SDA, - GPIO10_I2C2_SDA, - GPIO11_I2C2_SCL, - GPIO229_I2C3_SDA, - GPIO230_I2C3_SCL, - - /* SKE keypad */ - GPIO153_KP_I7, - GPIO154_KP_I6, - GPIO155_KP_I5, - GPIO156_KP_I4, - GPIO157_KP_O7, - GPIO158_KP_O6, - GPIO159_KP_O5, - GPIO160_KP_O4, - GPIO161_KP_I3, - GPIO162_KP_I2, - GPIO163_KP_I1, - GPIO164_KP_I0, - GPIO165_KP_O3, - GPIO166_KP_O2, - GPIO167_KP_O1, - GPIO168_KP_O0, -}; - -static void ab4500_spi_cs_control(u32 command) -{ - /* set the FRM signal, which is CS - TODO */ -} - -struct pl022_config_chip ab4500_chip_info = { - .com_mode = INTERRUPT_TRANSFER, - .iface = SSP_INTERFACE_MOTOROLA_SPI, - /* we can act as master only */ - .hierarchy = SSP_MASTER, - .slave_tx_disable = 0, - .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, - .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC, - .cs_control = ab4500_spi_cs_control, -}; - -static struct ab8500_platform_data ab8500_platdata = { - .irq_base = MOP500_AB8500_IRQ_BASE, -}; - -static struct resource ab8500_resources[] = { - [0] = { - .start = IRQ_AB8500, - .end = IRQ_AB8500, - .flags = IORESOURCE_IRQ - } -}; - -struct platform_device ab8500_device = { - .name = "ab8500-i2c", - .id = 0, - .dev = { - .platform_data = &ab8500_platdata, - }, - .num_resources = 1, - .resource = ab8500_resources, -}; - -static struct spi_board_info ab8500_spi_devices[] = { - { - .modalias = "ab8500-spi", - .controller_data = &ab4500_chip_info, - .platform_data = &ab8500_platdata, - .max_speed_hz = 12000000, - .bus_num = 0, - .chip_select = 0, - .mode = SPI_MODE_3, - .irq = IRQ_DB8500_AB8500, - }, -}; - -static struct pl022_ssp_controller ssp0_platform_data = { - .bus_id = 0, - /* pl022 not yet supports dma */ - .enable_dma = 0, - /* on this platform, gpio 31,142,144,214 & - * 224 are connected as chip selects - */ - .num_chipselect = 5, -}; - -#define U8500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \ -static struct nmk_i2c_controller u8500_i2c##id##_data = { \ - /* \ - * slave data setup time, which is \ - * 250 ns,100ns,10ns which is 14,6,2 \ - * respectively for a 48 Mhz \ - * i2c clock \ - */ \ - .slsu = _slsu, \ - /* Tx FIFO threshold */ \ - .tft = _tft, \ - /* Rx FIFO threshold */ \ - .rft = _rft, \ - /* std. mode operation */ \ - .clk_freq = clk, \ - .sm = _sm, \ -} - -/* - * The board uses 4 i2c controllers, initialize all of - * them with slave data setup time of 250 ns, - * Tx & Rx FIFO threshold values as 1 and standard - * mode of operation - */ -U8500_I2C_CONTROLLER(0, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD); -U8500_I2C_CONTROLLER(1, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD); -U8500_I2C_CONTROLLER(2, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD); -U8500_I2C_CONTROLLER(3, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD); - -static struct amba_device *amba_devs[] __initdata = { - &ux500_uart0_device, - &ux500_uart1_device, - &ux500_uart2_device, - &u8500_ssp0_device, -}; - -static const unsigned int ux500_keymap[] = { - KEY(2, 5, KEY_END), - KEY(4, 1, KEY_POWER), - KEY(3, 5, KEY_VOLUMEDOWN), - KEY(1, 3, KEY_3), - KEY(5, 2, KEY_RIGHT), - KEY(5, 0, KEY_9), - - KEY(0, 5, KEY_MENU), - KEY(7, 6, KEY_ENTER), - KEY(4, 5, KEY_0), - KEY(6, 7, KEY_2), - KEY(3, 4, KEY_UP), - KEY(3, 3, KEY_DOWN), - - KEY(6, 4, KEY_SEND), - KEY(6, 2, KEY_BACK), - KEY(4, 2, KEY_VOLUMEUP), - KEY(5, 5, KEY_1), - KEY(4, 3, KEY_LEFT), - KEY(3, 2, KEY_7), -}; - -static const struct matrix_keymap_data ux500_keymap_data = { - .keymap = ux500_keymap, - .keymap_size = ARRAY_SIZE(ux500_keymap), -}; - -/* - * Nomadik SKE keypad - */ -#define ROW_PIN_I0 164 -#define ROW_PIN_I1 163 -#define ROW_PIN_I2 162 -#define ROW_PIN_I3 161 -#define ROW_PIN_I4 156 -#define ROW_PIN_I5 155 -#define ROW_PIN_I6 154 -#define ROW_PIN_I7 153 -#define COL_PIN_O0 168 -#define COL_PIN_O1 167 -#define COL_PIN_O2 166 -#define COL_PIN_O3 165 -#define COL_PIN_O4 160 -#define COL_PIN_O5 159 -#define COL_PIN_O6 158 -#define COL_PIN_O7 157 - -#define SKE_KPD_MAX_ROWS 8 -#define SKE_KPD_MAX_COLS 8 - -static int ske_kp_rows[] = { - ROW_PIN_I0, ROW_PIN_I1, ROW_PIN_I2, ROW_PIN_I3, - ROW_PIN_I4, ROW_PIN_I5, ROW_PIN_I6, ROW_PIN_I7, -}; - -/* - * ske_set_gpio_row: request and set gpio rows - */ -static int ske_set_gpio_row(int gpio) -{ - int ret; - - ret = gpio_request(gpio, "ske-kp"); - if (ret < 0) { - pr_err("ske_set_gpio_row: gpio request failed\n"); - return ret; - } - - ret = gpio_direction_output(gpio, 1); - if (ret < 0) { - pr_err("ske_set_gpio_row: gpio direction failed\n"); - gpio_free(gpio); - } - - return ret; -} - -/* - * ske_kp_init - enable the gpio configuration - */ -static int ske_kp_init(void) -{ - int ret, i; - - for (i = 0; i < SKE_KPD_MAX_ROWS; i++) { - ret = ske_set_gpio_row(ske_kp_rows[i]); - if (ret < 0) { - pr_err("ske_kp_init: failed init\n"); - return ret; - } - } - - return 0; -} - -static struct ske_keypad_platform_data ske_keypad_board = { - .init = ske_kp_init, - .keymap_data = &ux500_keymap_data, - .no_autorepeat = true, - .krow = SKE_KPD_MAX_ROWS, /* 8x8 matrix */ - .kcol = SKE_KPD_MAX_COLS, - .debounce_ms = 40, /* in millsecs */ -}; - - - -/* add any platform devices here - TODO */ -static struct platform_device *platform_devs[] __initdata = { - &u8500_i2c0_device, - &ux500_i2c1_device, - &ux500_i2c2_device, - &ux500_i2c3_device, - &ux500_ske_keypad_device, -}; - -static void __init u8500_init_machine(void) -{ - int i; - - u8500_init_devices(); - - nmk_config_pins(mop500_pins, ARRAY_SIZE(mop500_pins)); - - u8500_i2c0_device.dev.platform_data = &u8500_i2c0_data; - ux500_i2c1_device.dev.platform_data = &u8500_i2c1_data; - ux500_i2c2_device.dev.platform_data = &u8500_i2c2_data; - ux500_i2c3_device.dev.platform_data = &u8500_i2c3_data; - ux500_ske_keypad_device.dev.platform_data = &ske_keypad_board; - - u8500_ssp0_device.dev.platform_data = &ssp0_platform_data; - - /* Register the active AMBA devices on this board */ - for (i = 0; i < ARRAY_SIZE(amba_devs); i++) - amba_device_register(amba_devs[i], &iomem_resource); - - platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs)); - - mop500_sdi_init(); - - /* If HW is early drop (ED) or V1.0 then use SPI to access AB8500 */ - if (cpu_is_u8500ed() || cpu_is_u8500v10()) - spi_register_board_info(ab8500_spi_devices, - ARRAY_SIZE(ab8500_spi_devices)); - else /* If HW is v.1.1 or later use I2C to access AB8500 */ - platform_device_register(&ab8500_device); -} - -MACHINE_START(U8500, "ST-Ericsson MOP500 platform") - /* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */ - .boot_params = 0x100, - .map_io = u8500_map_io, - .init_irq = ux500_init_irq, - /* we re-use nomadik timer here */ - .timer = &ux500_timer, - .init_machine = u8500_init_machine, -MACHINE_END |