1 files changed, 93 insertions, 223 deletions

diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
index 0c108a212ea..a2e035e0792 100644
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ b/arch/arm/mach-omap2/board-omap3stalker.c
@@ -24,39 +24,37 @@
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
+#include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
 #include <linux/mmc/host.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/spi/spi.h>
+#include <linux/interrupt.h>
+#include <linux/smsc911x.h>
+#include <linux/platform_data/at24.h>
+#include <linux/usb/phy.h>
 
-#include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 
-#include <plat/board.h>
-#include <plat/common.h>
-#include <plat/gpmc.h>
-#include <plat/nand.h>
-#include <plat/usb.h>
+#include "common.h"
+#include "gpmc.h"
+#include <linux/platform_data/mtd-nand-omap2.h>
 #include <video/omapdss.h>
-#include <video/omap-panel-generic-dpi.h>
+#include <video/omap-panel-data.h>
 
-#include <plat/mcspi.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/i2c/at24.h>
+#include <linux/platform_data/spi-omap2-mcspi.h>
 
 #include "sdram-micron-mt46h32m32lf-6.h"
 #include "mux.h"
 #include "hsmmc.h"
-#include "timer-gp.h"
 #include "common-board-devices.h"
 
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include <plat/gpmc-smsc911x.h>
+#include "gpmc-smsc911x.h"
 
 #define OMAP3STALKER_ETHR_START	0x2c000000
 #define OMAP3STALKER_ETHR_SIZE	1024
@@ -72,15 +70,6 @@ static struct omap_smsc911x_platform_data smsc911x_cfg = {
 
 static inline void __init omap3stalker_init_eth(void)
 {
-	struct clk *l3ck;
-	unsigned int rate;
-
-	l3ck = clk_get(NULL, "l3_ck");
-	if (IS_ERR(l3ck))
-		rate = 100000000;
-	else
-		rate = clk_get_rate(l3ck);
-
 	omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
 	gpmc_smsc911x_init(&smsc911x_cfg);
 }
@@ -100,118 +89,58 @@ static inline void __init omap3stalker_init_eth(void)
 #define LCD_PANEL_BKLIGHT_GPIO	210
 #define ENABLE_VPLL2_DEV_GRP	0xE0
 
-static int lcd_enabled;
-static int dvi_enabled;
-
 static void __init omap3_stalker_display_init(void)
 {
 	return;
 }
-
-static int omap3_stalker_enable_lcd(struct omap_dss_device *dssdev)
-{
-	if (dvi_enabled) {
-		printk(KERN_ERR "cannot enable LCD, DVI is enabled\n");
-		return -EINVAL;
-	}
-	gpio_set_value(DSS_ENABLE_GPIO, 1);
-	gpio_set_value(LCD_PANEL_BKLIGHT_GPIO, 1);
-	lcd_enabled = 1;
-	return 0;
-}
-
-static void omap3_stalker_disable_lcd(struct omap_dss_device *dssdev)
-{
-	gpio_set_value(DSS_ENABLE_GPIO, 0);
-	gpio_set_value(LCD_PANEL_BKLIGHT_GPIO, 0);
-	lcd_enabled = 0;
-}
-
-static struct panel_generic_dpi_data lcd_panel = {
-	.name			= "generic",
-	.platform_enable	= omap3_stalker_enable_lcd,
-	.platform_disable	= omap3_stalker_disable_lcd,
+static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
+	.name                   = "dvi",
+	.source                 = "tfp410.0",
+	.i2c_bus_num            = -1,
 };
 
-static struct omap_dss_device omap3_stalker_lcd_device = {
-	.name			= "lcd",
-	.driver_name		= "generic_dpi_panel",
-	.data			= &lcd_panel,
-	.phy.dpi.data_lines	= 24,
-	.type			= OMAP_DISPLAY_TYPE_DPI,
+static struct platform_device omap3stalker_dvi_connector_device = {
+	.name                   = "connector-dvi",
+	.id                     = 0,
+	.dev.platform_data      = &omap3stalker_dvi_connector_pdata,
 };
 
-static int omap3_stalker_enable_tv(struct omap_dss_device *dssdev)
-{
-	return 0;
-}
-
-static void omap3_stalker_disable_tv(struct omap_dss_device *dssdev)
-{
-}
-
-static struct omap_dss_device omap3_stalker_tv_device = {
-	.name			= "tv",
-	.driver_name		= "venc",
-	.type			= OMAP_DISPLAY_TYPE_VENC,
-#if defined(CONFIG_OMAP2_VENC_OUT_TYPE_SVIDEO)
-	.phy.venc.type		= OMAP_DSS_VENC_TYPE_SVIDEO,
-#elif defined(CONFIG_OMAP2_VENC_OUT_TYPE_COMPOSITE)
-	.u.venc.type		= OMAP_DSS_VENC_TYPE_COMPOSITE,
-#endif
-	.platform_enable	= omap3_stalker_enable_tv,
-	.platform_disable	= omap3_stalker_disable_tv,
+static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
+	.name                   = "tfp410.0",
+	.source                 = "dpi.0",
+	.data_lines             = 24,
+	.power_down_gpio        = DSS_ENABLE_GPIO,
 };
 
-static int omap3_stalker_enable_dvi(struct omap_dss_device *dssdev)
-{
-	if (lcd_enabled) {
-		printk(KERN_ERR "cannot enable DVI, LCD is enabled\n");
-		return -EINVAL;
-	}
-	gpio_set_value(DSS_ENABLE_GPIO, 1);
-	dvi_enabled = 1;
-	return 0;
-}
-
-static void omap3_stalker_disable_dvi(struct omap_dss_device *dssdev)
-{
-	gpio_set_value(DSS_ENABLE_GPIO, 0);
-	dvi_enabled = 0;
-}
-
-static struct panel_generic_dpi_data dvi_panel = {
-	.name			= "generic",
-	.platform_enable	= omap3_stalker_enable_dvi,
-	.platform_disable	= omap3_stalker_disable_dvi,
+static struct platform_device omap3stalker_tfp410_device = {
+	.name                   = "tfp410",
+	.id                     = 0,
+	.dev.platform_data      = &omap3stalker_tfp410_pdata,
 };
 
-static struct omap_dss_device omap3_stalker_dvi_device = {
-	.name			= "dvi",
-	.type			= OMAP_DISPLAY_TYPE_DPI,
-	.driver_name		= "generic_dpi_panel",
-	.data			= &dvi_panel,
-	.phy.dpi.data_lines	= 24,
+static struct connector_atv_platform_data omap3stalker_tv_pdata = {
+	.name = "tv",
+	.source = "venc.0",
+	.connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
+	.invert_polarity = false,
 };
 
-static struct omap_dss_device *omap3_stalker_dss_devices[] = {
-	&omap3_stalker_lcd_device,
-	&omap3_stalker_tv_device,
-	&omap3_stalker_dvi_device,
+static struct platform_device omap3stalker_tv_connector_device = {
+	.name                   = "connector-analog-tv",
+	.id                     = 0,
+	.dev.platform_data      = &omap3stalker_tv_pdata,
 };
 
 static struct omap_dss_board_info omap3_stalker_dss_data = {
-	.num_devices	= ARRAY_SIZE(omap3_stalker_dss_devices),
-	.devices	= omap3_stalker_dss_devices,
-	.default_device	= &omap3_stalker_dvi_device,
+	.default_display_name = "dvi",
 };
 
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply = {
-	.supply		= "vmmc",
+static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
+	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
 };
 
-static struct regulator_consumer_supply omap3stalker_vsim_supply = {
-	.supply		= "vmmc_aux",
+static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
+	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
 };
 
 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
@@ -224,8 +153,8 @@ static struct regulator_init_data omap3stalker_vmmc1 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
 		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &omap3stalker_vmmc1_supply,
+	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vmmc1_supply),
+	.consumer_supplies	= omap3stalker_vmmc1_supply,
 };
 
 /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
@@ -238,16 +167,17 @@ static struct regulator_init_data omap3stalker_vsim = {
 		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
 		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &omap3stalker_vsim_supply,
+	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vsim_supply),
+	.consumer_supplies	= omap3stalker_vsim_supply,
 };
 
 static struct omap2_hsmmc_info mmc[] = {
 	{
-	 .mmc		= 1,
-	 .caps		= MMC_CAP_4_BIT_DATA,
-	 .gpio_cd	= -EINVAL,
-	 .gpio_wp	= 23,
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= 23,
+		.deferred	= true,
 	 },
 	{}			/* Terminator */
 };
@@ -317,13 +247,8 @@ omap3stalker_twl_gpio_setup(struct device *dev,
 			    unsigned gpio, unsigned ngpio)
 {
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
-
-	/* link regulators to MMC adapters */
-	omap3stalker_vmmc1_supply.dev = mmc[0].dev;
-	omap3stalker_vsim_supply.dev = mmc[0].dev;
+	omap_hsmmc_late_init(mmc);
 
 	/*
 	 * Most GPIOs are for USB OTG.  Some are mostly sent to
@@ -347,17 +272,10 @@ omap3stalker_twl_gpio_setup(struct device *dev,
 }
 
 static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
-	.gpio_base	= OMAP_MAX_GPIO_LINES,
-	.irq_base	= TWL4030_GPIO_IRQ_BASE,
-	.irq_end	= TWL4030_GPIO_IRQ_END,
 	.use_leds	= true,
 	.setup		= omap3stalker_twl_gpio_setup,
 };
 
-static struct twl4030_usb_data omap3stalker_usb_data = {
-	.usb_mode	= T2_USB_MODE_ULPI,
-};
-
 static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_DOWN),
@@ -392,68 +310,10 @@ static struct twl4030_keypad_data omap3stalker_kp_data = {
 	.rep		= 1,
 };
 
-static struct twl4030_madc_platform_data omap3stalker_madc_data = {
-	.irq_line	= 1,
-};
-
-static struct twl4030_codec_audio_data omap3stalker_audio_data;
-
-static struct twl4030_codec_data omap3stalker_codec_data = {
-	.audio_mclk	= 26000000,
-	.audio		= &omap3stalker_audio_data,
-};
-
-static struct regulator_consumer_supply omap3_stalker_vdda_dac_supply =
-	REGULATOR_SUPPLY("vdda_dac", "omapdss_venc");
-
-/* VDAC for DSS driving S-Video */
-static struct regulator_init_data omap3_stalker_vdac = {
-	.constraints		= {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-		| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-		| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &omap3_stalker_vdda_dac_supply,
-};
-
-/* VPLL2 for digital video outputs */
-static struct regulator_consumer_supply omap3_stalker_vpll2_supplies[] = {
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"),
-};
-
-static struct regulator_init_data omap3_stalker_vpll2 = {
-	.constraints		= {
-		.name			= "VDVI",
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV = true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-		| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-		| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3_stalker_vpll2_supplies),
-	.consumer_supplies	= omap3_stalker_vpll2_supplies,
-};
-
 static struct twl4030_platform_data omap3stalker_twldata = {
-	.irq_base	= TWL4030_IRQ_BASE,
-	.irq_end	= TWL4030_IRQ_END,
-
 	/* platform_data for children goes here */
 	.keypad		= &omap3stalker_kp_data,
-	.madc		= &omap3stalker_madc_data,
-	.usb		= &omap3stalker_usb_data,
 	.gpio		= &omap3stalker_gpio_data,
-	.codec		= &omap3stalker_codec_data,
-	.vdac		= &omap3_stalker_vdac,
-	.vpll2		= &omap3_stalker_vpll2,
 	.vmmc1		= &omap3stalker_vmmc1,
 	.vsim		= &omap3stalker_vsim,
 };
@@ -474,6 +334,15 @@ static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
 
 static int __init omap3_stalker_i2c_init(void)
 {
+	omap3_pmic_get_config(&omap3stalker_twldata,
+			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
+			TWL_COMMON_PDATA_AUDIO,
+			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
+
+	omap3stalker_twldata.vdac->constraints.apply_uV = true;
+	omap3stalker_twldata.vpll2->constraints.apply_uV = true;
+	omap3stalker_twldata.vpll2->constraints.name = "VDVI";
+
 	omap3_pmic_init("twl4030", &omap3stalker_twldata);
 	omap_register_i2c_bus(2, 400, NULL, 0);
 	omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
@@ -483,36 +352,23 @@ static int __init omap3_stalker_i2c_init(void)
 
 #define OMAP3_STALKER_TS_GPIO	175
 
-static struct omap_board_config_kernel omap3_stalker_config[] __initdata = {
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = 21,
+		.vcc_gpio = -EINVAL,
+	},
 };
 
-static void __init omap3_stalker_init_early(void)
-{
-	omap2_init_common_infrastructure();
-	omap2_init_common_devices(mt46h32m32lf6_sdrc_params, NULL);
-}
-
-static void __init omap3_stalker_init_irq(void)
-{
-	omap_init_irq();
-#ifdef CONFIG_OMAP_32K_TIMER
-	omap2_gp_clockevent_set_gptimer(12);
-#endif
-}
-
 static struct platform_device *omap3_stalker_devices[] __initdata = {
 	&keys_gpio,
+	&omap3stalker_tfp410_device,
+	&omap3stalker_dvi_connector_device,
+	&omap3stalker_tv_connector_device,
 };
 
-static struct usbhs_omap_board_data usbhs_bdata __initconst = {
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset = true,
-	.reset_gpio_port[0] = -EINVAL,
-	.reset_gpio_port[1] = 21,
-	.reset_gpio_port[2] = -EINVAL,
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -525,11 +381,18 @@ static struct omap_board_mux board_mux[] __initdata = {
 };
 #endif
 
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+};
+
 static void __init omap3_stalker_init(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-	omap_board_config = omap3_stalker_config;
-	omap_board_config_size = ARRAY_SIZE(omap3_stalker_config);
+
+	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
+	omap_hsmmc_init(mmc);
 
 	omap3_stalker_i2c_init();
 
@@ -539,7 +402,11 @@ static void __init omap3_stalker_init(void)
 	omap_display_init(&omap3_stalker_dss_data);
 
 	omap_serial_init();
+	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
+	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
 
@@ -555,10 +422,13 @@ static void __init omap3_stalker_init(void)
 
 MACHINE_START(SBC3530, "OMAP3 STALKER")
 	/* Maintainer: Jason Lam -lzg@ema-tech.com */
-	.boot_params		= 0x80000100,
+	.atag_offset		= 0x100,
 	.map_io			= omap3_map_io,
-	.init_early		= omap3_stalker_init_early,
-	.init_irq		= omap3_stalker_init_irq,
+	.init_early		= omap35xx_init_early,
+	.init_irq		= omap3_init_irq,
+	.handle_irq		= omap3_intc_handle_irq,
 	.init_machine		= omap3_stalker_init,
-	.timer			= &omap_timer,
+	.init_late		= omap35xx_init_late,
+	.init_time		= omap3_secure_sync32k_timer_init,
+	.restart		= omap3xxx_restart,
 MACHINE_END