1 files changed, 87 insertions, 194 deletions

diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index f396756872b..aead77a4bc6 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -16,29 +16,23 @@
 #include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/irq.h>
 #include <linux/stddef.h>
 #include <linux/i2c.h>
 #include <linux/spi/spi.h>
 #include <linux/usb/musb.h>
+#include <linux/platform_data/spi-omap2-mcspi.h>
+#include <linux/platform_data/mtd-onenand-omap2.h>
+#include <linux/mfd/menelaus.h>
 #include <sound/tlv320aic3x.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
-#include <plat/board.h>
-#include <plat/common.h>
-#include <plat/menelaus.h>
-#include <mach/irqs.h>
-#include <plat/mcspi.h>
-#include <plat/onenand.h>
-#include <plat/mmc.h>
-#include <plat/serial.h>
-
-#include "mux.h"
-
-static int slot1_cover_open;
-static int slot2_cover_open;
-static struct device *mmc_device;
+#include "common.h"
+#include "mmc.h"
+#include "soc.h"
+#include "gpmc-onenand.h"
 
 #define TUSB6010_ASYNC_CS	1
 #define TUSB6010_SYNC_CS	4
@@ -46,7 +40,32 @@ static struct device *mmc_device;
 #define TUSB6010_GPIO_ENABLE	0
 #define TUSB6010_DMACHAN	0x3f
 
-#ifdef CONFIG_USB_MUSB_TUSB6010
+#define NOKIA_N810_WIMAX	(1 << 2)
+#define NOKIA_N810		(1 << 1)
+#define NOKIA_N800		(1 << 0)
+
+static u32 board_caps;
+
+#define board_is_n800()		(board_caps & NOKIA_N800)
+#define board_is_n810()		(board_caps & NOKIA_N810)
+#define board_is_n810_wimax()	(board_caps & NOKIA_N810_WIMAX)
+
+static void board_check_revision(void)
+{
+	if (of_have_populated_dt()) {
+		if (of_machine_is_compatible("nokia,n800"))
+			board_caps = NOKIA_N800;
+		else if (of_machine_is_compatible("nokia,n810"))
+			board_caps = NOKIA_N810;
+		else if (of_machine_is_compatible("nokia,n810-wimax"))
+			board_caps = NOKIA_N810_WIMAX;
+	}
+
+	if (!board_caps)
+		pr_err("Unknown board\n");
+}
+
+#if defined(CONFIG_USB_MUSB_TUSB6010) || defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
 /*
  * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
  * 1.5 V voltage regulators of PM companion chip. Companion chip will then
@@ -87,13 +106,7 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data tusb_data = {
-#if defined(CONFIG_USB_MUSB_OTG)
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
-	.mode		= MUSB_PERIPHERAL,
-#else /* defined(CONFIG_USB_MUSB_HOST) */
-	.mode		= MUSB_HOST,
-#endif
 	.set_power	= tusb_set_power,
 	.min_power	= 25,	/* x2 = 50 mA drawn from VBUS as peripheral */
 	.power		= 100,	/* Max 100 mA VBUS for host mode */
@@ -106,14 +119,13 @@ static void __init n8x0_usb_init(void)
 	static char	announce[] __initdata = KERN_INFO "TUSB 6010\n";
 
 	/* PM companion chip power control pin */
-	ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
+	ret = gpio_request_one(TUSB6010_GPIO_ENABLE, GPIOF_OUT_INIT_LOW,
+			       "TUSB6010 enable");
 	if (ret != 0) {
 		printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
 		       TUSB6010_GPIO_ENABLE);
 		return;
 	}
-	gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
-
 	tusb_set_power(0);
 
 	ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
@@ -138,7 +150,6 @@ static void __init n8x0_usb_init(void) {}
 
 static struct omap2_mcspi_device_config p54spi_mcspi_config = {
 	.turbo_mode	= 0,
-	.single_channel = 1,
 };
 
 static struct spi_board_info n800_spi_board_info[] __initdata = {
@@ -151,49 +162,6 @@ static struct spi_board_info n800_spi_board_info[] __initdata = {
 	},
 };
 
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
-	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
-
-static struct mtd_partition onenand_partitions[] = {
-	{
-		.name           = "bootloader",
-		.offset         = 0,
-		.size           = 0x20000,
-		.mask_flags     = MTD_WRITEABLE,	/* Force read-only */
-	},
-	{
-		.name           = "config",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 0x60000,
-	},
-	{
-		.name           = "kernel",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 0x200000,
-	},
-	{
-		.name           = "initfs",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 0x400000,
-	},
-	{
-		.name           = "rootfs",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = MTDPART_SIZ_FULL,
-	},
-};
-
-static struct omap_onenand_platform_data board_onenand_data[] = {
-	{
-		.cs		= 0,
-		.gpio_irq	= 26,
-		.parts		= onenand_partitions,
-		.nr_parts	= ARRAY_SIZE(onenand_partitions),
-		.flags		= ONENAND_SYNC_READ,
-	}
-};
-#endif
-
 #if defined(CONFIG_MENELAUS) &&						\
 	(defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE))
 
@@ -212,6 +180,10 @@ static struct omap_onenand_platform_data board_onenand_data[] = {
 #define N810_EMMC_VSD_GPIO	23
 #define N810_EMMC_VIO_GPIO	9
 
+static int slot1_cover_open;
+static int slot2_cover_open;
+static struct device *mmc_device;
+
 static int n8x0_mmc_switch_slot(struct device *dev, int slot)
 {
 #ifdef CONFIG_MMC_DEBUG
@@ -311,7 +283,7 @@ static void n810_set_power_emmc(struct device *dev,
 static int n8x0_mmc_set_power(struct device *dev, int slot, int power_on,
 			      int vdd)
 {
-	if (machine_is_nokia_n800() || slot == 0)
+	if (board_is_n800() || slot == 0)
 		return n8x0_mmc_set_power_menelaus(dev, slot, power_on, vdd);
 
 	n810_set_power_emmc(dev, power_on);
@@ -357,7 +329,7 @@ static void n8x0_mmc_callback(void *data, u8 card_mask)
 {
 	int bit, *openp, index;
 
-	if (machine_is_nokia_n800()) {
+	if (board_is_n800()) {
 		bit = 1 << 1;
 		openp = &slot2_cover_open;
 		index = 1;
@@ -372,7 +344,11 @@ static void n8x0_mmc_callback(void *data, u8 card_mask)
 	else
 		*openp = 0;
 
+#ifdef CONFIG_MMC_OMAP
 	omap_mmc_notify_cover_event(mmc_device, index, *openp);
+#else
+	pr_warn("MMC: notify cover event not available\n");
+#endif
 }
 
 static int n8x0_mmc_late_init(struct device *dev)
@@ -386,7 +362,7 @@ static int n8x0_mmc_late_init(struct device *dev)
 	if (r < 0)
 		return r;
 
-	if (machine_is_nokia_n800())
+	if (board_is_n800())
 		vs2sel = 0;
 	else
 		vs2sel = 2;
@@ -409,7 +385,7 @@ static int n8x0_mmc_late_init(struct device *dev)
 	if (r < 0)
 		return r;
 
-	if (machine_is_nokia_n800()) {
+	if (board_is_n800()) {
 		bit = 1 << 1;
 		openp = &slot2_cover_open;
 	} else {
@@ -436,7 +412,7 @@ static void n8x0_mmc_shutdown(struct device *dev)
 {
 	int vs2sel;
 
-	if (machine_is_nokia_n800())
+	if (board_is_n800())
 		vs2sel = 0;
 	else
 		vs2sel = 2;
@@ -451,7 +427,7 @@ static void n8x0_mmc_cleanup(struct device *dev)
 
 	gpio_free(N8X0_SLOT_SWITCH_GPIO);
 
-	if (machine_is_nokia_n810()) {
+	if (board_is_n810()) {
 		gpio_free(N810_EMMC_VSD_GPIO);
 		gpio_free(N810_EMMC_VIO_GPIO);
 	}
@@ -462,13 +438,12 @@ static void n8x0_mmc_cleanup(struct device *dev)
  * MMC controller2 is not in use.
  */
 static struct omap_mmc_platform_data mmc1_data = {
-	.nr_slots			= 2,
+	.nr_slots			= 0,
 	.switch_slot			= n8x0_mmc_switch_slot,
 	.init				= n8x0_mmc_late_init,
 	.cleanup			= n8x0_mmc_cleanup,
 	.shutdown			= n8x0_mmc_shutdown,
 	.max_freq			= 24000000,
-	.dma_mask			= 0xffffffff,
 	.slots[0] = {
 		.wires			= 4,
 		.set_power		= n8x0_mmc_set_power,
@@ -494,12 +469,16 @@ static struct omap_mmc_platform_data mmc1_data = {
 
 static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];
 
-static void __init n8x0_mmc_init(void)
+static struct gpio n810_emmc_gpios[] __initdata = {
+	{ N810_EMMC_VSD_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vddf" },
+	{ N810_EMMC_VIO_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vdd"  },
+};
 
+static void __init n8x0_mmc_init(void)
 {
 	int err;
 
-	if (machine_is_nokia_n810()) {
+	if (board_is_n810()) {
 		mmc1_data.slots[0].name = "external";
 
 		/*
@@ -512,34 +491,25 @@ static void __init n8x0_mmc_init(void)
 		mmc1_data.slots[1].ban_openended = 1;
 	}
 
-	err = gpio_request(N8X0_SLOT_SWITCH_GPIO, "MMC slot switch");
+	err = gpio_request_one(N8X0_SLOT_SWITCH_GPIO, GPIOF_OUT_INIT_LOW,
+			       "MMC slot switch");
 	if (err)
 		return;
 
-	gpio_direction_output(N8X0_SLOT_SWITCH_GPIO, 0);
-
-	if (machine_is_nokia_n810()) {
-		err = gpio_request(N810_EMMC_VSD_GPIO, "MMC slot 2 Vddf");
-		if (err) {
-			gpio_free(N8X0_SLOT_SWITCH_GPIO);
-			return;
-		}
-		gpio_direction_output(N810_EMMC_VSD_GPIO, 0);
-
-		err = gpio_request(N810_EMMC_VIO_GPIO, "MMC slot 2 Vdd");
+	if (board_is_n810()) {
+		err = gpio_request_array(n810_emmc_gpios,
+					 ARRAY_SIZE(n810_emmc_gpios));
 		if (err) {
 			gpio_free(N8X0_SLOT_SWITCH_GPIO);
-			gpio_free(N810_EMMC_VSD_GPIO);
 			return;
 		}
-		gpio_direction_output(N810_EMMC_VIO_GPIO, 0);
 	}
 
+	mmc1_data.nr_slots = 2;
 	mmc_data[0] = &mmc1_data;
-	omap2_init_mmc(mmc_data, OMAP24XX_NR_MMC);
 }
 #else
-
+static struct omap_mmc_platform_data mmc1_data;
 void __init n8x0_mmc_init(void)
 {
 }
@@ -559,8 +529,8 @@ static int n8x0_auto_sleep_regulators(void)
 
 	ret = menelaus_set_regulator_sleep(1, val);
 	if (ret < 0) {
-		printk(KERN_ERR "Could not set regulators to sleep on "
-			"menelaus: %u\n", ret);
+		pr_err("Could not set regulators to sleep on menelaus: %u\n",
+		       ret);
 		return ret;
 	}
 	return 0;
@@ -572,8 +542,7 @@ static int n8x0_auto_voltage_scale(void)
 
 	ret = menelaus_set_vcore_hw(1400, 1050);
 	if (ret < 0) {
-		printk(KERN_ERR "Could not set VCORE voltage on "
-			"menelaus: %u\n", ret);
+		pr_err("Could not set VCORE voltage on menelaus: %u\n", ret);
 		return ret;
 	}
 	return 0;
@@ -606,7 +575,7 @@ static struct menelaus_platform_data n8x0_menelaus_platform_data __initdata = {
 static struct i2c_board_info __initdata n8x0_i2c_board_info_1[] __initdata = {
 	{
 		I2C_BOARD_INFO("menelaus", 0x72),
-		.irq = INT_24XX_SYS_NIRQ,
+		.irq = 7 + OMAP_INTC_START,
 		.platform_data = &n8x0_menelaus_platform_data,
 	},
 };
@@ -622,108 +591,32 @@ static struct i2c_board_info n810_i2c_board_info_2[] __initdata = {
 	},
 };
 
-static void __init n8x0_map_io(void)
-{
-	omap2_set_globals_242x();
-	omap242x_map_common_io();
-}
-
-static void __init n8x0_init_irq(void)
+static int __init n8x0_late_initcall(void)
 {
-	omap2_init_common_infrastructure();
-	omap2_init_common_devices(NULL, NULL);
-	omap_init_irq();
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* I2S codec port pins for McBSP block */
-	OMAP2420_MUX(EAC_AC_SCLK, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP2420_MUX(EAC_AC_FS, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP2420_MUX(EAC_AC_DIN, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP2420_MUX(EAC_AC_DOUT, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
+	if (!board_caps)
+		return -ENODEV;
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	{
-		.name	= "uart3_rx_irrx.uart3_rx_irrx",
-		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
-		.enable	= OMAP_MUX_MODE0,
-		.idle	= OMAP_MUX_MODE3	/* Mux as GPIO for idle */
-	},
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-
-	bdata.flags = 0;
-	bdata.pads = NULL;
-	bdata.pads_cnt = 0;
-
-	bdata.id = 0;
-	omap_serial_init_port(&bdata);
-
-	bdata.id = 1;
-	omap_serial_init_port(&bdata);
-
-	bdata.id = 2;
-	bdata.pads = serial2_pads;
-	bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
-	omap_serial_init_port(&bdata);
-}
-
-#else
+	n8x0_mmc_init();
+	n8x0_usb_init();
 
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
+	return 0;
 }
+omap_late_initcall(n8x0_late_initcall);
 
-#endif
-
-static void __init n8x0_init_machine(void)
+/*
+ * Legacy init pdata init for n8x0. Note that we want to follow the
+ * I2C bus numbering starting at 0 for device tree like other omaps.
+ */
+void * __init n8x0_legacy_init(void)
 {
-	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
-	/* FIXME: add n810 spi devices */
+	board_check_revision();
 	spi_register_board_info(n800_spi_board_info,
 				ARRAY_SIZE(n800_spi_board_info));
-	omap_register_i2c_bus(1, 400, n8x0_i2c_board_info_1,
-			      ARRAY_SIZE(n8x0_i2c_board_info_1));
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	if (machine_is_nokia_n810())
-		i2c_register_board_info(2, n810_i2c_board_info_2,
+	i2c_register_board_info(0, n8x0_i2c_board_info_1,
+				ARRAY_SIZE(n8x0_i2c_board_info_1));
+	if (board_is_n810())
+		i2c_register_board_info(1, n810_i2c_board_info_2,
 					ARRAY_SIZE(n810_i2c_board_info_2));
-	board_serial_init();
-	gpmc_onenand_init(board_onenand_data);
-	n8x0_mmc_init();
-	n8x0_usb_init();
-}
 
-MACHINE_START(NOKIA_N800, "Nokia N800")
-	.boot_params	= 0x80000100,
-	.map_io		= n8x0_map_io,
-	.reserve	= omap_reserve,
-	.init_irq	= n8x0_init_irq,
-	.init_machine	= n8x0_init_machine,
-	.timer		= &omap_timer,
-MACHINE_END
-
-MACHINE_START(NOKIA_N810, "Nokia N810")
-	.boot_params	= 0x80000100,
-	.map_io		= n8x0_map_io,
-	.reserve	= omap_reserve,
-	.init_irq	= n8x0_init_irq,
-	.init_machine	= n8x0_init_machine,
-	.timer		= &omap_timer,
-MACHINE_END
-
-MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
-	.boot_params	= 0x80000100,
-	.map_io		= n8x0_map_io,
-	.reserve	= omap_reserve,
-	.init_irq	= n8x0_init_irq,
-	.init_machine	= n8x0_init_machine,
-	.timer		= &omap_timer,
-MACHINE_END
+	return &mmc1_data;
+}