1 files changed, 131 insertions, 8 deletions

diff --git a/arch/arm/mach-omap1/usb.c b/arch/arm/mach-omap1/usb.c
index 19de03b074e..4118db50d5e 100644
--- a/arch/arm/mach-omap1/usb.c
+++ b/arch/arm/mach-omap1/usb.c
@@ -26,8 +26,11 @@
 
 #include <asm/irq.h>
 
-#include <plat/mux.h>
-#include <plat/usb.h>
+#include <mach/mux.h>
+
+#include <mach/usb.h>
+
+#include "common.h"
 
 /* These routines should handle the standard chip-specific modes
  * for usb0/1/2 ports, covering basic mux and transceiver setup.
@@ -53,7 +56,120 @@
 #define INT_USB_IRQ_HGEN	INT_USB_HHC_1
 #define INT_USB_IRQ_OTG		IH2_BASE + 8
 
-#ifdef	CONFIG_USB_GADGET_OMAP
+#ifdef	CONFIG_ARCH_OMAP_OTG
+
+void __init
+omap_otg_init(struct omap_usb_config *config)
+{
+	u32		syscon;
+	int		alt_pingroup = 0;
+
+	/* NOTE:  no bus or clock setup (yet?) */
+
+	syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
+	if (!(syscon & OTG_RESET_DONE))
+		pr_debug("USB resets not complete?\n");
+
+	//omap_writew(0, OTG_IRQ_EN);
+
+	/* pin muxing and transceiver pinouts */
+	if (config->pins[0] > 2)	/* alt pingroup 2 */
+		alt_pingroup = 1;
+	syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
+	syscon |= config->usb1_init(config->pins[1]);
+	syscon |= config->usb2_init(config->pins[2], alt_pingroup);
+	pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+	omap_writel(syscon, OTG_SYSCON_1);
+
+	syscon = config->hmc_mode;
+	syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
+#ifdef	CONFIG_USB_OTG
+	if (config->otg)
+		syscon |= OTG_EN;
+#endif
+	if (cpu_class_is_omap1())
+		pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
+			 omap_readl(USB_TRANSCEIVER_CTRL));
+	pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
+	omap_writel(syscon, OTG_SYSCON_2);
+
+	printk("USB: hmc %d", config->hmc_mode);
+	if (!alt_pingroup)
+		printk(", usb2 alt %d wires", config->pins[2]);
+	else if (config->pins[0])
+		printk(", usb0 %d wires%s", config->pins[0],
+			is_usb0_device(config) ? " (dev)" : "");
+	if (config->pins[1])
+		printk(", usb1 %d wires", config->pins[1]);
+	if (!alt_pingroup && config->pins[2])
+		printk(", usb2 %d wires", config->pins[2]);
+	if (config->otg)
+		printk(", Mini-AB on usb%d", config->otg - 1);
+	printk("\n");
+
+	if (cpu_class_is_omap1()) {
+		u16 w;
+
+		/* leave USB clocks/controllers off until needed */
+		w = omap_readw(ULPD_SOFT_REQ);
+		w &= ~SOFT_USB_CLK_REQ;
+		omap_writew(w, ULPD_SOFT_REQ);
+
+		w = omap_readw(ULPD_CLOCK_CTRL);
+		w &= ~USB_MCLK_EN;
+		w |= DIS_USB_PVCI_CLK;
+		omap_writew(w, ULPD_CLOCK_CTRL);
+	}
+	syscon = omap_readl(OTG_SYSCON_1);
+	syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
+
+#if IS_ENABLED(CONFIG_USB_OMAP)
+	if (config->otg || config->register_dev) {
+		struct platform_device *udc_device = config->udc_device;
+		int status;
+
+		syscon &= ~DEV_IDLE_EN;
+		udc_device->dev.platform_data = config;
+		status = platform_device_register(udc_device);
+		if (status)
+			pr_debug("can't register UDC device, %d\n", status);
+	}
+#endif
+
+#if	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	if (config->otg || config->register_host) {
+		struct platform_device *ohci_device = config->ohci_device;
+		int status;
+
+		syscon &= ~HST_IDLE_EN;
+		ohci_device->dev.platform_data = config;
+		status = platform_device_register(ohci_device);
+		if (status)
+			pr_debug("can't register OHCI device, %d\n", status);
+	}
+#endif
+
+#ifdef	CONFIG_USB_OTG
+	if (config->otg) {
+		struct platform_device *otg_device = config->otg_device;
+		int status;
+
+		syscon &= ~OTG_IDLE_EN;
+		otg_device->dev.platform_data = config;
+		status = platform_device_register(otg_device);
+		if (status)
+			pr_debug("can't register OTG device, %d\n", status);
+	}
+#endif
+	pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+	omap_writel(syscon, OTG_SYSCON_1);
+}
+
+#else
+void omap_otg_init(struct omap_usb_config *config) {}
+#endif
+
+#if IS_ENABLED(CONFIG_USB_OMAP)
 
 static struct resource udc_resources[] = {
 	/* order is significant! */
@@ -138,6 +254,7 @@ static inline void ohci_device_init(struct omap_usb_config *pdata)
 	if (cpu_is_omap7xx())
 		ohci_resources[1].start = INT_7XX_USB_HHC_1;
 	pdata->ohci_device = &ohci_device;
+	pdata->ocpi_enable = &ocpi_enable;
 }
 
 #else
@@ -184,7 +301,7 @@ static inline void otg_device_init(struct omap_usb_config *pdata)
 
 #endif
 
-u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
+static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
 {
 	u32	syscon1 = 0;
 
@@ -292,7 +409,7 @@ u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
 	return syscon1 << 16;
 }
 
-u32 __init omap1_usb1_init(unsigned nwires)
+static u32 __init omap1_usb1_init(unsigned nwires)
 {
 	u32	syscon1 = 0;
 
@@ -358,7 +475,7 @@ bad:
 	return syscon1 << 20;
 }
 
-u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
+static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
 {
 	u32	syscon1 = 0;
 
@@ -483,7 +600,7 @@ static void __init omap_1510_usb_init(struct omap_usb_config *config)
 	while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
 		cpu_relax();
 
-#ifdef	CONFIG_USB_GADGET_OMAP
+#if IS_ENABLED(CONFIG_USB_OMAP)
 	if (config->register_dev) {
 		int status;
 
@@ -512,8 +629,14 @@ static void __init omap_1510_usb_init(struct omap_usb_config *config)
 static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
 #endif
 
-void __init omap1_usb_init(struct omap_usb_config *pdata)
+void __init omap1_usb_init(struct omap_usb_config *_pdata)
 {
+	struct omap_usb_config *pdata;
+
+	pdata = kmemdup(_pdata, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return;
+
 	pdata->usb0_init = omap1_usb0_init;
 	pdata->usb1_init = omap1_usb1_init;
 	pdata->usb2_init = omap1_usb2_init;