diff options
Diffstat (limited to 'arch/arm/mach-omap1/board-osk.c')
| -rw-r--r-- | arch/arm/mach-omap1/board-osk.c | 415 |
1 files changed, 249 insertions, 166 deletions
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index 5279e35a8ae..7436d4cf659 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -25,33 +25,49 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 675 Mass Ave, Cambridge, MA 02139, USA. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/interrupt.h> #include <linux/irq.h> #include <linux/i2c.h> - +#include <linux/leds.h> +#include <linux/smc91x.h> +#include <linux/omapfb.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> - +#include <linux/mtd/physmap.h> #include <linux/i2c/tps65010.h> - -#include <asm/hardware.h> -#include <asm/gpio.h> +#include <linux/platform_data/gpio-omap.h> +#include <linux/platform_data/omap1_bl.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> -#include <asm/mach/flash.h> -#include <asm/arch/usb.h> -#include <asm/arch/mux.h> -#include <asm/arch/tc.h> -#include <asm/arch/common.h> -#include <asm/arch/mcbsp.h> -#include <asm/arch/omap-alsa.h> +#include <mach/flash.h> +#include <mach/mux.h> +#include <mach/tc.h> + +#include <mach/hardware.h> +#include <mach/usb.h> + +#include "common.h" + +/* At OMAP5912 OSK the Ethernet is directly connected to CS1 */ +#define OMAP_OSK_ETHR_START 0x04800300 + +/* TPS65010 has four GPIOs. nPG and LED2 can be treated like GPIOs with + * alternate pin configurations for hardware-controlled blinking. + */ +#define OSK_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */) +# define OSK_TPS_GPIO_USB_PWR_EN (OSK_TPS_GPIO_BASE + 0) +# define OSK_TPS_GPIO_LED_D3 (OSK_TPS_GPIO_BASE + 1) +# define OSK_TPS_GPIO_LAN_RESET (OSK_TPS_GPIO_BASE + 2) +# define OSK_TPS_GPIO_DSP_PWR_EN (OSK_TPS_GPIO_BASE + 3) +# define OSK_TPS_GPIO_LED_D9 (OSK_TPS_GPIO_BASE + 4) +# define OSK_TPS_GPIO_LED_D2 (OSK_TPS_GPIO_BASE + 5) static struct mtd_partition osk_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ @@ -80,9 +96,9 @@ static struct mtd_partition osk_partitions[] = { } }; -static struct flash_platform_data osk_flash_data = { - .map_name = "cfi_probe", +static struct physmap_flash_data osk_flash_data = { .width = 2, + .set_vpp = omap1_set_vpp, .parts = osk_partitions, .nr_parts = ARRAY_SIZE(osk_partitions), }; @@ -93,7 +109,7 @@ static struct resource osk_flash_resource = { }; static struct platform_device osk5912_flash_device = { - .name = "omapflash", + .name = "physmap-flash", .id = 0, .dev = { .platform_data = &osk_flash_data, @@ -102,6 +118,12 @@ static struct platform_device osk5912_flash_device = { .resource = &osk_flash_resource, }; +static struct smc91x_platdata osk5912_smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, + .leda = RPC_LED_100_10, + .ledb = RPC_LED_TX_RX, +}; + static struct resource osk5912_smc91x_resources[] = { [0] = { .start = OMAP_OSK_ETHR_START, /* Physical */ @@ -109,8 +131,6 @@ static struct resource osk5912_smc91x_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .start = OMAP_GPIO_IRQ(0), - .end = OMAP_GPIO_IRQ(0), .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, }, }; @@ -118,14 +138,15 @@ static struct resource osk5912_smc91x_resources[] = { static struct platform_device osk5912_smc91x_device = { .name = "smc91x", .id = -1, + .dev = { + .platform_data = &osk5912_smc91x_info, + }, .num_resources = ARRAY_SIZE(osk5912_smc91x_resources), .resource = osk5912_smc91x_resources, }; static struct resource osk5912_cf_resources[] = { [0] = { - .start = OMAP_GPIO_IRQ(62), - .end = OMAP_GPIO_IRQ(62), .flags = IORESOURCE_IRQ, }, }; @@ -140,91 +161,121 @@ static struct platform_device osk5912_cf_device = { .resource = osk5912_cf_resources, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 = FREE | FRST | GRST | XRST | XINTM(3), - .spcr1 = RINTM(3) | RRST, - .rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) | - RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(0), - .rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16), - .xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) | - XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(0) | XFIG, - .xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16), - .srgr1 = FWID(DEFAULT_BITPERSAMPLE - 1), - .srgr2 = GSYNC | CLKSP | FSGM | FPER(DEFAULT_BITPERSAMPLE * 2 - 1), - /*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 = CLKXP | CLKRP, /* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name = "OSK AIC23", - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev = NULL, /* aic23_configure, */ - .codec_set_samplerate = NULL, /* aic23_set_samplerate, */ - .codec_clock_setup = NULL, /* aic23_clock_setup, */ - .codec_clock_on = NULL, /* aic23_clock_on, */ - .codec_clock_off = NULL, /* aic23_clock_off, */ - .get_default_samplerate = NULL, /* aic23_get_default_samplerate, */ -}; - -static struct platform_device osk5912_mcbsp1_device = { - .name = "omap_alsa_mcbsp", - .id = 1, - .dev = { - .platform_data = &alsa_config, - }, -}; - static struct platform_device *osk5912_devices[] __initdata = { &osk5912_flash_device, &osk5912_smc91x_device, &osk5912_cf_device, - &osk5912_mcbsp1_device, +}; + +static struct gpio_led tps_leds[] = { + /* NOTE: D9 and D2 have hardware blink support. + * Also, D9 requires non-battery power. + */ + { .gpio = OSK_TPS_GPIO_LED_D9, .name = "d9", + .default_trigger = "ide-disk", }, + { .gpio = OSK_TPS_GPIO_LED_D2, .name = "d2", }, + { .gpio = OSK_TPS_GPIO_LED_D3, .name = "d3", .active_low = 1, + .default_trigger = "heartbeat", }, +}; + +static struct gpio_led_platform_data tps_leds_data = { + .num_leds = 3, + .leds = tps_leds, +}; + +static struct platform_device osk5912_tps_leds = { + .name = "leds-gpio", + .id = 0, + .dev.platform_data = &tps_leds_data, +}; + +static int osk_tps_setup(struct i2c_client *client, void *context) +{ + if (!IS_BUILTIN(CONFIG_TPS65010)) + return -ENOSYS; + + /* Set GPIO 1 HIGH to disable VBUS power supply; + * OHCI driver powers it up/down as needed. + */ + gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en"); + gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1); + + /* Set GPIO 2 high so LED D3 is off by default */ + tps65010_set_gpio_out_value(GPIO2, HIGH); + + /* Set GPIO 3 low to take ethernet out of reset */ + gpio_request(OSK_TPS_GPIO_LAN_RESET, "smc_reset"); + gpio_direction_output(OSK_TPS_GPIO_LAN_RESET, 0); + + /* GPIO4 is VDD_DSP */ + gpio_request(OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power"); + gpio_direction_output(OSK_TPS_GPIO_DSP_PWR_EN, 1); + /* REVISIT if DSP support isn't configured, power it off ... */ + + /* Let LED1 (D9) blink; leds-gpio may override it */ + tps65010_set_led(LED1, BLINK); + + /* Set LED2 off by default */ + tps65010_set_led(LED2, OFF); + + /* Enable LOW_PWR handshake */ + tps65010_set_low_pwr(ON); + + /* Switch VLDO2 to 3.0V for AIC23 */ + tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V + | TPS_LDO1_ENABLE); + + /* register these three LEDs */ + osk5912_tps_leds.dev.parent = &client->dev; + platform_device_register(&osk5912_tps_leds); + + return 0; +} + +static struct tps65010_board tps_board = { + .base = OSK_TPS_GPIO_BASE, + .outmask = 0x0f, + .setup = osk_tps_setup, }; static struct i2c_board_info __initdata osk_i2c_board_info[] = { { I2C_BOARD_INFO("tps65010", 0x48), - .type = "tps65010", - .irq = OMAP_GPIO_IRQ(OMAP_MPUIO(1)), + .platform_data = &tps_board, + + }, + { + I2C_BOARD_INFO("tlv320aic23", 0x1B), }, /* TODO when driver support is ready: - * - aic23 audio chip at 0x1a - * - on Mistral, 24c04 eeprom at 0x50 * - optionally on Mistral, ov9640 camera sensor at 0x30 */ }; static void __init osk_init_smc91x(void) { - if ((omap_request_gpio(0)) < 0) { + u32 l; + + if ((gpio_request(0, "smc_irq")) < 0) { printk("Error requesting gpio 0 for smc91x irq\n"); return; } /* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */ - EMIFS_CCS(1) |= 0x3; + l = omap_readl(EMIFS_CCS(1)); + l |= 0x3; + omap_writel(l, EMIFS_CCS(1)); } static void __init osk_init_cf(void) { omap_cfg_reg(M7_1610_GPIO62); - if ((omap_request_gpio(62)) < 0) { + if ((gpio_request(62, "cf_irq")) < 0) { printk("Error requesting gpio 62 for CF irq\n"); return; } /* the CF I/O IRQ is really active-low */ - set_irq_type(OMAP_GPIO_IRQ(62), IRQT_FALLING); -} - -static void __init osk_init_irq(void) -{ - omap1_init_common_hw(); - omap_init_irq(); - omap_gpio_init(); - osk_init_smc91x(); - osk_init_cf(); + irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING); } static struct omap_usb_config osk_usb_config __initdata = { @@ -232,7 +283,7 @@ static struct omap_usb_config osk_usb_config __initdata = { * be used, with a NONSTANDARD gender-bending cable/dongle, as * a peripheral. */ -#ifdef CONFIG_USB_GADGET_OMAP +#if IS_ENABLED(CONFIG_USB_OMAP) .register_dev = 1, .hmc_mode = 0, #else @@ -243,51 +294,59 @@ static struct omap_usb_config osk_usb_config __initdata = { .pins[0] = 2, }; -static struct omap_uart_config osk_uart_config __initdata = { - .enabled_uarts = (1 << 0), -}; - #ifdef CONFIG_OMAP_OSK_MISTRAL static struct omap_lcd_config osk_lcd_config __initdata = { .ctrl_name = "internal", }; #endif -static struct omap_board_config_kernel osk_config[] __initdata = { - { OMAP_TAG_USB, &osk_usb_config }, - { OMAP_TAG_UART, &osk_uart_config }, -#ifdef CONFIG_OMAP_OSK_MISTRAL - { OMAP_TAG_LCD, &osk_lcd_config }, -#endif -}; - #ifdef CONFIG_OMAP_OSK_MISTRAL #include <linux/input.h> +#include <linux/platform_data/at24.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> -#include <asm/arch/keypad.h> +#include <linux/platform_data/keypad-omap.h> + +static struct at24_platform_data at24c04 = { + .byte_len = SZ_4K / 8, + .page_size = 16, +}; + +static struct i2c_board_info __initdata mistral_i2c_board_info[] = { + { + /* NOTE: powered from LCD supply */ + I2C_BOARD_INFO("24c04", 0x50), + .platform_data = &at24c04, + }, + /* TODO when driver support is ready: + * - optionally ov9640 camera sensor at 0x30 + */ +}; -static const int osk_keymap[] = { +static const unsigned int osk_keymap[] = { /* KEY(col, row, code) */ KEY(0, 0, KEY_F1), /* SW4 */ - KEY(0, 3, KEY_UP), /* (sw2/up) */ + KEY(3, 0, KEY_UP), /* (sw2/up) */ KEY(1, 1, KEY_LEFTCTRL), /* SW5 */ - KEY(1, 2, KEY_LEFT), /* (sw2/left) */ - KEY(2, 0, KEY_SPACE), /* SW3 */ - KEY(2, 1, KEY_ESC), /* SW6 */ + KEY(2, 1, KEY_LEFT), /* (sw2/left) */ + KEY(0, 2, KEY_SPACE), /* SW3 */ + KEY(1, 2, KEY_ESC), /* SW6 */ KEY(2, 2, KEY_DOWN), /* (sw2/down) */ - KEY(3, 2, KEY_ENTER), /* (sw2/select) */ + KEY(2, 3, KEY_ENTER), /* (sw2/select) */ KEY(3, 3, KEY_RIGHT), /* (sw2/right) */ - 0 +}; + +static const struct matrix_keymap_data osk_keymap_data = { + .keymap = osk_keymap, + .keymap_size = ARRAY_SIZE(osk_keymap), }; static struct omap_kp_platform_data osk_kp_data = { .rows = 8, .cols = 8, - .keymap = (int *) osk_keymap, - .keymapsize = ARRAY_SIZE(osk_keymap), + .keymap_data = &osk_keymap_data, .delay = 9, }; @@ -326,15 +385,42 @@ static struct platform_device osk5912_lcd_device = { .id = -1, }; +static struct gpio_led mistral_gpio_led_pins[] = { + { + .name = "mistral:red", + .default_trigger = "heartbeat", + .gpio = 3, + }, + { + .name = "mistral:green", + .default_trigger = "cpu0", + .gpio = OMAP_MPUIO(4), + }, +}; + +static struct gpio_led_platform_data mistral_gpio_led_data = { + .leds = mistral_gpio_led_pins, + .num_leds = ARRAY_SIZE(mistral_gpio_led_pins), +}; + +static struct platform_device mistral_gpio_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &mistral_gpio_led_data, + }, +}; + static struct platform_device *mistral_devices[] __initdata = { &osk5912_kp_device, &mistral_bl_device, &osk5912_lcd_device, + &mistral_gpio_leds, }; static int mistral_get_pendown_state(void) { - return !omap_get_gpio_datain(4); + return !gpio_get_value(4); } static const struct ads7846_platform_data mistral_ts_info = { @@ -349,7 +435,6 @@ static struct spi_board_info __initdata mistral_boardinfo[] = { { /* MicroWire (bus 2) CS0 has an ads7846e */ .modalias = "ads7846", .platform_data = &mistral_ts_info, - .irq = OMAP_GPIO_IRQ(4), .max_speed_hz = 120000 /* max sample rate at 3V */ * 26 /* command + data + overhead */, .bus_num = 2, @@ -396,40 +481,54 @@ static void __init osk_mistral_init(void) omap_cfg_reg(W14_1610_CCP_DATAP); /* CAM_PWDN */ - if (omap_request_gpio(11) == 0) { + if (gpio_request(11, "cam_pwdn") == 0) { omap_cfg_reg(N20_1610_GPIO11); - omap_set_gpio_direction(11, 0 /* out */); - omap_set_gpio_dataout(11, 0 /* off */); + gpio_direction_output(11, 0); } else pr_debug("OSK+Mistral: CAM_PWDN is awol\n"); /* omap_cfg_reg(P19_1610_GPIO6); */ /* BUSY */ + gpio_request(6, "ts_busy"); + gpio_direction_input(6); + omap_cfg_reg(P20_1610_GPIO4); /* PENIRQ */ - set_irq_type(OMAP_GPIO_IRQ(4), IRQT_FALLING); + gpio_request(4, "ts_int"); + gpio_direction_input(4); + irq_set_irq_type(gpio_to_irq(4), IRQ_TYPE_EDGE_FALLING); + + mistral_boardinfo[0].irq = gpio_to_irq(4); spi_register_board_info(mistral_boardinfo, ARRAY_SIZE(mistral_boardinfo)); - /* the sideways button (SW1) is for use as a "wakeup" button */ + /* the sideways button (SW1) is for use as a "wakeup" button + * + * NOTE: The Mistral board has the wakeup button (SW1) wired + * to the LCD 3.3V rail, which is powered down during suspend. + * To allow this button to wake up the omap, work around this + * HW bug by rewiring SW1 to use the main 3.3V rail. + */ omap_cfg_reg(N15_1610_MPUIO2); - if (omap_request_gpio(OMAP_MPUIO(2)) == 0) { + if (gpio_request(OMAP_MPUIO(2), "wakeup") == 0) { int ret = 0; - omap_set_gpio_direction(OMAP_MPUIO(2), 1); - set_irq_type(OMAP_GPIO_IRQ(OMAP_MPUIO(2)), IRQT_RISING); + int irq = gpio_to_irq(OMAP_MPUIO(2)); + + gpio_direction_input(OMAP_MPUIO(2)); + irq_set_irq_type(irq, IRQ_TYPE_EDGE_RISING); #ifdef CONFIG_PM /* share the IRQ in case someone wants to use the * button for more than wakeup from system sleep. */ - ret = request_irq(OMAP_GPIO_IRQ(OMAP_MPUIO(2)), + ret = request_irq(irq, &osk_mistral_wake_interrupt, IRQF_SHARED, "mistral_wakeup", &osk_mistral_wake_interrupt); if (ret != 0) { - omap_free_gpio(OMAP_MPUIO(2)); + gpio_free(OMAP_MPUIO(2)); printk(KERN_ERR "OSK+Mistral: no wakeup irq, %d?\n", ret); } else - enable_irq_wake(OMAP_GPIO_IRQ(OMAP_MPUIO(2))); + enable_irq_wake(irq); #endif } else printk(KERN_ERR "OSK+Mistral: wakeup button is awol\n"); @@ -438,10 +537,17 @@ static void __init osk_mistral_init(void) * board, like the touchscreen, EEPROM, and wakeup (!) switch. */ omap_cfg_reg(PWL); - if (omap_request_gpio(2) == 0) { - omap_set_gpio_direction(2, 0 /* out */); - omap_set_gpio_dataout(2, 1 /* on */); - } + if (gpio_request(2, "lcd_pwr") == 0) + gpio_direction_output(2, 1); + + /* + * GPIO based LEDs + */ + omap_cfg_reg(P18_1610_GPIO3); + omap_cfg_reg(MPUIO4); + + i2c_register_board_info(1, mistral_i2c_board_info, + ARRAY_SIZE(mistral_i2c_board_info)); platform_add_devices(mistral_devices, ARRAY_SIZE(mistral_devices)); } @@ -453,20 +559,33 @@ static void __init osk_mistral_init(void) { } static void __init osk_init(void) { + u32 l; + + osk_init_smc91x(); + osk_init_cf(); + /* Workaround for wrong CS3 (NOR flash) timing * There are some U-Boot versions out there which configure * wrong CS3 memory timings. This mainly leads to CRC * or similar errors if you use NOR flash (e.g. with JFFS2) */ - if (EMIFS_CCS(3) != EMIFS_CS3_VAL) - EMIFS_CCS(3) = EMIFS_CS3_VAL; + l = omap_readl(EMIFS_CCS(3)); + if (l != EMIFS_CS3_VAL) + omap_writel(EMIFS_CS3_VAL, EMIFS_CCS(3)); osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys(); osk_flash_resource.end += SZ_32M - 1; + osk5912_smc91x_resources[1].start = gpio_to_irq(0); + osk5912_smc91x_resources[1].end = gpio_to_irq(0); + osk5912_cf_resources[0].start = gpio_to_irq(62); + osk5912_cf_resources[0].end = gpio_to_irq(62); platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices)); - omap_board_config = osk_config; - omap_board_config_size = ARRAY_SIZE(osk_config); - USB_TRANSCEIVER_CTRL_REG |= (3 << 1); + + l = omap_readl(USB_TRANSCEIVER_CTRL); + l |= (3 << 1); + omap_writel(l, USB_TRANSCEIVER_CTRL); + + omap1_usb_init(&osk_usb_config); /* irq for tps65010 chip */ /* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */ @@ -474,61 +593,25 @@ static void __init osk_init(void) gpio_direction_input(OMAP_MPUIO(1)); omap_serial_init(); + osk_i2c_board_info[0].irq = gpio_to_irq(OMAP_MPUIO(1)); omap_register_i2c_bus(1, 400, osk_i2c_board_info, ARRAY_SIZE(osk_i2c_board_info)); osk_mistral_init(); -} - -static void __init osk_map_io(void) -{ - omap1_map_common_io(); -} - -#ifdef CONFIG_TPS65010 -static int __init osk_tps_init(void) -{ - if (!machine_is_omap_osk()) - return 0; - - /* Let LED1 (D9) blink */ - tps65010_set_led(LED1, BLINK); - - /* Disable LED 2 (D2) */ - tps65010_set_led(LED2, OFF); - - /* Set GPIO 1 HIGH to disable VBUS power supply; - * OHCI driver powers it up/down as needed. - */ - tps65010_set_gpio_out_value(GPIO1, HIGH); - - /* Set GPIO 2 low to turn on LED D3 */ - tps65010_set_gpio_out_value(GPIO2, HIGH); - - /* Set GPIO 3 low to take ethernet out of reset */ - tps65010_set_gpio_out_value(GPIO3, LOW); - - /* gpio4 for VDD_DSP */ - /* FIXME send power to DSP iff it's configured */ - - /* Enable LOW_PWR */ - tps65010_set_low_pwr(ON); - /* Switch VLDO2 to 3.0V for AIC23 */ - tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V - | TPS_LDO1_ENABLE); +#ifdef CONFIG_OMAP_OSK_MISTRAL + omapfb_set_lcd_config(&osk_lcd_config); +#endif - return 0; } -fs_initcall(osk_tps_init); -#endif MACHINE_START(OMAP_OSK, "TI-OSK") /* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */ - .phys_io = 0xfff00000, - .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc, - .boot_params = 0x10000100, - .map_io = osk_map_io, - .init_irq = osk_init_irq, + .atag_offset = 0x100, + .map_io = omap16xx_map_io, + .init_early = omap1_init_early, + .init_irq = omap1_init_irq, .init_machine = osk_init, - .timer = &omap_timer, + .init_late = omap1_init_late, + .init_time = omap1_timer_init, + .restart = omap1_restart, MACHINE_END |