diff options
Diffstat (limited to 'arch/arm/mach-imx/Kconfig')
| -rw-r--r-- | arch/arm/mach-imx/Kconfig | 397 |
1 files changed, 290 insertions, 107 deletions
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 59c97a33113..4b5185748f7 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -1,65 +1,137 @@ -config IMX_HAVE_DMA_V1 +menuconfig ARCH_MXC + bool "Freescale i.MX family" if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 + select ARCH_HAS_OPP + select ARCH_REQUIRE_GPIOLIB + select ARM_CPU_SUSPEND if PM + select CLKSRC_MMIO + select GENERIC_IRQ_CHIP + select PINCTRL + select PM_OPP if PM + select SOC_BUS + select SRAM + help + Support for Freescale MXC/iMX-based family of processors + +if ARCH_MXC + +config MXC_TZIC bool -# -# ARCH_MX31 and ARCH_MX35 are left for compatibility -# Some usages assume that having one of them implies not having (e.g.) ARCH_MX2. -# To easily distinguish good and reviewed from unreviewed usages new (and IMHO -# more sensible) names are used: SOC_IMX31 and SOC_IMX35 -config ARCH_MX31 + +config MXC_AVIC + bool + +config MXC_DEBUG_BOARD + bool "Enable MXC debug board(for 3-stack)" + help + The debug board is an integral part of the MXC 3-stack(PDK) + platforms, it can be attached or removed from the peripheral + board. On debug board, several debug devices(ethernet, UART, + buttons, LEDs and JTAG) are implemented. Between the MCU and + these devices, a CPLD is added as a bridge which performs + data/address de-multiplexing and decode, signal level shift, + interrupt control and various board functions. + +config HAVE_EPIT + bool + +config MXC_USE_EPIT + bool "Use EPIT instead of GPT" + depends on HAVE_EPIT + help + Use EPIT as the system timer on systems that have it. Normally you + don't have a reason to do so as the EPIT has the same features and + uses the same clocks as the GPT. Anyway, on some systems the GPT + may be in use for other purposes. + +config ARCH_HAS_RNGA bool -config ARCH_MX35 +config HAVE_IMX_ANATOP + bool + +config HAVE_IMX_GPC + bool + +config HAVE_IMX_MMDC + bool + +config HAVE_IMX_SRC + def_bool y if SMP + select ARCH_HAS_RESET_CONTROLLER + +config IMX_HAVE_IOMUX_V1 + bool + +config ARCH_MXC_IOMUX_V3 + bool + +config ARCH_MX1 + bool + +config ARCH_MX25 + bool + +config MACH_MX27 bool config SOC_IMX1 bool + select ARCH_MX1 select CPU_ARM920T - select IMX_HAVE_DMA_V1 select IMX_HAVE_IOMUX_V1 select MXC_AVIC config SOC_IMX21 bool select CPU_ARM926T - select ARCH_MXC_AUDMUX_V1 - select IMX_HAVE_DMA_V1 select IMX_HAVE_IOMUX_V1 select MXC_AVIC config SOC_IMX25 bool - select CPU_ARM926T - select ARCH_MXC_AUDMUX_V2 + select ARCH_MX25 select ARCH_MXC_IOMUX_V3 + select CPU_ARM926T select MXC_AVIC + select PINCTRL_IMX25 config SOC_IMX27 bool + select ARCH_HAS_OPP select CPU_ARM926T - select ARCH_MXC_AUDMUX_V1 - select IMX_HAVE_DMA_V1 select IMX_HAVE_IOMUX_V1 + select MACH_MX27 select MXC_AVIC + select PINCTRL_IMX27 config SOC_IMX31 bool select CPU_V6 select IMX_HAVE_PLATFORM_MXC_RNGA - select ARCH_MXC_AUDMUX_V2 - select ARCH_MX31 select MXC_AVIC + select SMP_ON_UP if SMP config SOC_IMX35 bool - select CPU_V6 select ARCH_MXC_IOMUX_V3 - select ARCH_MXC_AUDMUX_V2 select HAVE_EPIT - select ARCH_MX35 select MXC_AVIC + select PINCTRL_IMX35 + select SMP_ON_UP if SMP +config SOC_IMX5 + bool + select ARCH_HAS_OPP + select ARCH_MXC_IOMUX_V3 + select MXC_TZIC + +config SOC_IMX51 + bool + select HAVE_IMX_SRC + select PINCTRL_IMX51 + select SOC_IMX5 -if ARCH_MX1 +if ARCH_MULTI_V4T comment "MX1 platforms:" config MACH_MXLADS @@ -67,88 +139,67 @@ config MACH_MXLADS config ARCH_MX1ADS bool "MX1ADS platform" - select MACH_MXLADS - select SOC_IMX1 select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART + select MACH_MXLADS + select SOC_IMX1 help Say Y here if you are using Motorola MX1ADS/MXLADS boards config MACH_SCB9328 bool "Synertronixx scb9328" select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX1 help Say Y here if you are using a Synertronixx scb9328 board config MACH_APF9328 bool "APF9328" - select SOC_IMX1 + select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX1 help Say Yes here if you are using the Armadeus APF9328 development board endif -if ARCH_MX2 - -choice - prompt "CPUs:" - default MACH_MX21 - -config MACH_MX21 - bool "i.MX21 support" - help - This enables support for Freescale's MX2 based i.MX21 processor. - -config MACH_MX27 - bool "i.MX27 support" - help - This enables support for Freescale's MX2 based i.MX27 processor. - -endchoice - -endif - -if MACH_MX21 +if ARCH_MULTI_V5 comment "MX21 platforms:" config MACH_MX21ADS bool "MX21ADS platform" - select SOC_IMX21 select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND + select SOC_IMX21 help Include support for MX21ADS platform. This includes specific configurations for the board and its peripherals. -endif - -if ARCH_MX25 - comment "MX25 platforms:" config MACH_MX25_3DS bool "Support MX25PDK (3DS) Platform" - select SOC_IMX25 + select IMX_HAVE_PLATFORM_FLEXCAN select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMXDI_RTC - select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_FB + select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_KEYPAD select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX + select SOC_IMX25 -config MACH_EUKREA_CPUIMX25 +config MACH_EUKREA_CPUIMX25SD bool "Support Eukrea CPUIMX25 Platform" - select SOC_IMX25 select IMX_HAVE_PLATFORM_FLEXCAN select IMX_HAVE_PLATFORM_FSL_USB2_UDC + select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMXDI_RTC select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C @@ -156,45 +207,50 @@ config MACH_EUKREA_CPUIMX25 select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX25 choice prompt "Baseboard" - depends on MACH_EUKREA_CPUIMX25 + depends on MACH_EUKREA_CPUIMX25SD default MACH_EUKREA_MBIMXSD25_BASEBOARD config MACH_EUKREA_MBIMXSD25_BASEBOARD bool "Eukrea MBIMXSD development board" select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX_SSI + select IMX_HAVE_PLATFORM_SPI_IMX + select LEDS_GPIO_REGISTER help This adds board specific devices that can be found on Eukrea's MBIMXSD evaluation board. endchoice -endif - -if MACH_MX27 +config MACH_IMX25_DT + bool "Support i.MX25 platforms from device tree" + select SOC_IMX25 + help + Include support for Freescale i.MX25 based platforms + using the device tree for discovery comment "MX27 platforms:" config MACH_MX27ADS bool "MX27ADS platform" - select SOC_IMX27 select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 + select SOC_IMX27 help Include support for MX27ADS platform. This includes specific configurations for the board and its peripherals. config MACH_PCM038 bool "Phytec phyCORE-i.MX27 CPU module (pcm038)" - select SOC_IMX27 select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART @@ -202,7 +258,8 @@ config MACH_PCM038 select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 select IMX_HAVE_PLATFORM_SPI_IMX - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX27 help Include support for phyCORE-i.MX27 (aka pcm038) platform. This includes specific configurations for the module and its peripherals. @@ -224,7 +281,6 @@ endchoice config MACH_CPUIMX27 bool "Eukrea CPUIMX27 module" - select SOC_IMX27 select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C @@ -232,7 +288,8 @@ config MACH_CPUIMX27 select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX27 help Include support for Eukrea CPUIMX27 platform. This includes specific configurations for the module and its peripherals. @@ -265,6 +322,7 @@ config MACH_EUKREA_MBIMX27_BASEBOARD select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX + select LEDS_GPIO_REGISTER help This adds board specific devices that can be found on Eukrea's MBIMX27 evaluation board. @@ -273,30 +331,36 @@ endchoice config MACH_MX27_3DS bool "MX27PDK platform" - select SOC_IMX27 select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT + select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_KEYPAD + select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART + select IMX_HAVE_PLATFORM_MX2_CAMERA select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX select MXC_DEBUG_BOARD - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX27 help Include support for MX27PDK platform. This includes specific configurations for the board and its peripherals. config MACH_IMX27_VISSTRIM_M10 bool "Vista Silicon i.MX27 Visstrim_m10" - select SOC_IMX27 select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART - select IMX_HAVE_PLATFORM_MXC_MMC + select IMX_HAVE_PLATFORM_MX2_CAMERA + select IMX_HAVE_PLATFORM_MX2_EMMA select IMX_HAVE_PLATFORM_MXC_EHCI + select IMX_HAVE_PLATFORM_MXC_MMC + select LEDS_GPIO_REGISTER + select SOC_IMX27 help Include support for Visstrim_m10 platform and its different variants. This includes specific configurations for the board and its @@ -304,16 +368,15 @@ config MACH_IMX27_VISSTRIM_M10 config MACH_IMX27LITE bool "LogicPD MX27 LITEKIT platform" - select SOC_IMX27 - select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IMX_SSI + select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX27 help Include support for MX27 LITEKIT platform. This includes specific configurations for the board and its peripherals. config MACH_PCA100 bool "Phytec phyCARD-s (pca100)" - select SOC_IMX27 select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_FB @@ -325,45 +388,53 @@ config MACH_PCA100 select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 select IMX_HAVE_PLATFORM_SPI_IMX - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX27 help Include support for phyCARD-s (aka pca100) platform. This includes specific configurations for the module and its peripherals. config MACH_MXT_TD60 bool "Maxtrack i-MXT TD60" - select SOC_IMX27 select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND + select SOC_IMX27 help Include support for i-MXT (aka td60) platform. This includes specific configurations for the module and its peripherals. config MACH_IMX27IPCAM bool "IMX27 IPCAM platform" - select SOC_IMX27 select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX27 help Include support for IMX27 IPCAM platform. This includes specific configurations for the board and its peripherals. +config MACH_IMX27_DT + bool "Support i.MX27 platforms from device tree" + select SOC_IMX27 + help + Include support for Freescale i.MX27 based platforms + using the device tree for discovery + endif -if ARCH_MX3 +if ARCH_MULTI_V6 comment "MX31 platforms:" config MACH_MX31ADS bool "Support MX31ADS platforms" - select SOC_IMX31 + default y select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART - default y + select SOC_IMX31 help Include support for MX31ADS platform. This includes specific configurations for the board and its peripherals. @@ -372,30 +443,26 @@ config MACH_MX31ADS_WM1133_EV1 bool "Support Wolfson Microelectronics 1133-EV1 module" depends on MACH_MX31ADS depends on MFD_WM8350_I2C - depends on REGULATOR_WM8350 - select MFD_WM8350_CONFIG_MODE_0 - select MFD_WM8352_CONFIG_MODE_0 + depends on REGULATOR_WM8350 = y help Include support for the Wolfson Microelectronics 1133-EV1 PMU and audio module for the MX31ADS platform. config MACH_MX31LILLY bool "Support MX31 LILLY-1131 platforms (INCO startec)" - select SOC_IMX31 select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX31 help Include support for mx31 based LILLY1131 modules. This includes specific configurations for the board and its peripherals. config MACH_MX31LITE bool "Support MX31 LITEKIT (LogicPD)" - select SOC_IMX31 - select MXC_ULPI if USB_ULPI select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_EHCI @@ -403,13 +470,15 @@ config MACH_MX31LITE select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_RTC select IMX_HAVE_PLATFORM_SPI_IMX + select LEDS_GPIO_REGISTER + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX31 help Include support for MX31 LITEKIT platform. This includes specific configurations for the board and its peripherals. config MACH_PCM037 bool "Support Phytec pcm037 (i.MX31) platforms" - select SOC_IMX31 select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C @@ -419,7 +488,8 @@ config MACH_PCM037 select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX31 help Include support for Phytec pcm037 platform. This includes specific configurations for the board and its peripherals. @@ -436,18 +506,20 @@ config MACH_PCM037_EET config MACH_MX31_3DS bool "Support MX31PDK (3DS)" - select SOC_IMX31 - select MXC_DEBUG_BOARD select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_KEYPAD + select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI + select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SPI_IMX - select MXC_ULPI if USB_ULPI + select MXC_DEBUG_BOARD + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX31 help Include support for MX31PDK (3DS) platform. This includes specific configurations for the board and its peripherals. @@ -463,30 +535,33 @@ config MACH_MX31_3DS_MXC_NAND_USE_BBT config MACH_MX31MOBOARD bool "Support mx31moboard platforms (EPFL Mobots group)" - select SOC_IMX31 select IMX_HAVE_PLATFORM_FSL_USB2_UDC + select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C + select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX - select MXC_ULPI if USB_ULPI + select LEDS_GPIO_REGISTER + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX31 help Include support for mx31moboard platform. This includes specific configurations for the board and its peripherals. config MACH_QONG bool "Support Dave/DENX QongEVB-LITE platform" - select SOC_IMX31 + select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX31 help Include support for Dave/DENX QongEVB-LITE platform. This includes specific configurations for the board and its peripherals. config MACH_ARMADILLO5X0 bool "Support Atmark Armadillo-500 Development Base Board" - select SOC_IMX31 select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART @@ -494,33 +569,47 @@ config MACH_ARMADILLO5X0 select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX31 help Include support for Atmark Armadillo-500 platform. This includes specific configurations for the board and its peripherals. config MACH_KZM_ARM11_01 bool "Support KZM-ARM11-01(Kyoto Microcomputer)" - select SOC_IMX31 select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX31 help Include support for KZM-ARM11-01. This includes specific configurations for the board and its peripherals. config MACH_BUG bool "Support Buglabs BUGBase platform" - select SOC_IMX31 - select IMX_HAVE_PLATFORM_IMX_UART default y + select IMX_HAVE_PLATFORM_IMX_UART + select SOC_IMX31 help Include support for BUGBase 1.3 platform. This includes specific configurations for the board and its peripherals. +config MACH_IMX31_DT + bool "Support i.MX31 platforms from device tree" + select SOC_IMX31 + help + Include support for Freescale i.MX31 based platforms + using the device tree for discovery. + comment "MX35 platforms:" +config MACH_IMX35_DT + bool "Support i.MX35 platforms from device tree" + select SOC_IMX35 + help + Include support for Freescale i.MX35 based platforms + using the device tree for discovery. + config MACH_PCM043 bool "Support Phytec pcm043 (i.MX35) platforms" - select SOC_IMX35 select IMX_HAVE_PLATFORM_FLEXCAN select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT @@ -531,29 +620,32 @@ config MACH_PCM043 select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX35 help Include support for Phytec pcm043 platform. This includes specific configurations for the board and its peripherals. config MACH_MX35_3DS bool "Support MX35PDK platform" - select SOC_IMX35 - select MXC_DEBUG_BOARD select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT + select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART + select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND + select IMX_HAVE_PLATFORM_MXC_RTC select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX + select MXC_DEBUG_BOARD + select SOC_IMX35 help Include support for MX35PDK platform. This includes specific configurations for the board and its peripherals. -config MACH_EUKREA_CPUIMX35 +config MACH_EUKREA_CPUIMX35SD bool "Support Eukrea CPUIMX35 Platform" - select SOC_IMX35 select IMX_HAVE_PLATFORM_FLEXCAN select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT @@ -562,14 +654,15 @@ config MACH_EUKREA_CPUIMX35 select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX - select MXC_ULPI if USB_ULPI + select USB_ULPI_VIEWPORT if USB_ULPI + select SOC_IMX35 help Include support for Eukrea CPUIMX35 platform. This includes specific configurations for the board and its peripherals. choice prompt "Baseboard" - depends on MACH_EUKREA_CPUIMX35 + depends on MACH_EUKREA_CPUIMX35SD default MACH_EUKREA_MBIMXSD35_BASEBOARD config MACH_EUKREA_MBIMXSD35_BASEBOARD @@ -577,6 +670,8 @@ config MACH_EUKREA_MBIMXSD35_BASEBOARD select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IPU_CORE + select IMX_HAVE_PLATFORM_SPI_IMX + select LEDS_GPIO_REGISTER help This adds board specific devices that can be found on Eukrea's MBIMXSD evaluation board. @@ -585,18 +680,106 @@ endchoice config MACH_VPR200 bool "Support VPR200 platform" - select SOC_IMX35 select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX2_WDT - select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IMX_I2C + select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX + select SOC_IMX35 help Include support for VPR200 platform. This includes specific configurations for the board and its peripherals. endif + +if ARCH_MULTI_V7 + +comment "Device tree only" + +config SOC_IMX50 + bool "i.MX50 support" + select HAVE_IMX_SRC + select PINCTRL_IMX50 + select SOC_IMX5 + + help + This enables support for Freescale i.MX50 processor. + +config MACH_IMX51_DT + bool "i.MX51 support" + select SOC_IMX51 + help + This enables support for Freescale i.MX51 processor + +config SOC_IMX53 + bool "i.MX53 support" + select HAVE_IMX_SRC + select PINCTRL_IMX53 + select SOC_IMX5 + + help + This enables support for Freescale i.MX53 processor. + +config SOC_IMX6 + bool + select ARM_ERRATA_754322 + select ARM_ERRATA_775420 + select ARM_GIC + select HAVE_IMX_ANATOP + select HAVE_IMX_GPC + select HAVE_IMX_MMDC + select HAVE_IMX_SRC + select MFD_SYSCON + select PL310_ERRATA_588369 if CACHE_L2X0 + select PL310_ERRATA_727915 if CACHE_L2X0 + select PL310_ERRATA_769419 if CACHE_L2X0 + +config SOC_IMX6Q + bool "i.MX6 Quad/DualLite support" + select ARM_ERRATA_764369 if SMP + select HAVE_ARM_SCU if SMP + select HAVE_ARM_TWD if SMP + select PCI_DOMAINS if PCI + select PINCTRL_IMX6Q + select SOC_IMX6 + + help + This enables support for Freescale i.MX6 Quad processor. + +config SOC_IMX6SL + bool "i.MX6 SoloLite support" + select PINCTRL_IMX6SL + select SOC_IMX6 + + help + This enables support for Freescale i.MX6 SoloLite processor. + +config SOC_IMX6SX + bool "i.MX6 SoloX support" + select PINCTRL_IMX6SX + select SOC_IMX6 + + help + This enables support for Freescale i.MX6 SoloX processor. + +config SOC_VF610 + bool "Vybrid Family VF610 support" + select ARM_GIC + select PINCTRL_VF610 + select VF_PIT_TIMER + select PL310_ERRATA_588369 if CACHE_L2X0 + select PL310_ERRATA_727915 if CACHE_L2X0 + select PL310_ERRATA_769419 if CACHE_L2X0 + + help + This enable support for Freescale Vybrid VF610 processor. + +endif + +source "arch/arm/mach-imx/devices/Kconfig" + +endif |