diff options
Diffstat (limited to 'arch/arm/mach-davinci/board-dm355-evm.c')
| -rw-r--r-- | arch/arm/mach-davinci/board-dm355-evm.c | 111 |
1 files changed, 90 insertions, 21 deletions
diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index 6e7cad13352..06d63d5651f 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -22,16 +22,19 @@ #include <media/tvp514x.h> #include <linux/spi/spi.h> #include <linux/spi/eeprom.h> +#include <linux/platform_data/gpio-davinci.h> +#include <linux/platform_data/i2c-davinci.h> +#include <linux/platform_data/mtd-davinci.h> +#include <linux/platform_data/mmc-davinci.h> +#include <linux/platform_data/usb-davinci.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <mach/dm355.h> -#include <mach/i2c.h> #include <mach/serial.h> -#include <mach/nand.h> -#include <mach/mmc.h> -#include <mach/usb.h> +#include <mach/common.h> + +#include "davinci.h" /* NOTE: this is geared for the standard config, with a socketed * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you @@ -77,7 +80,7 @@ static struct davinci_nand_pdata davinci_nand_data = { .parts = davinci_nand_partitions, .nr_parts = ARRAY_SIZE(davinci_nand_partitions), .ecc_mode = NAND_ECC_HW, - .options = NAND_USE_FLASH_BBT, + .bbt_options = NAND_BBT_USE_FLASH, .ecc_bits = 4, }; @@ -241,19 +244,80 @@ static struct vpfe_config vpfe_cfg = { .ccdc = "DM355 CCDC", }; +/* venc standards timings */ +static struct vpbe_enc_mode_info dm355evm_enc_preset_timing[] = { + { + .name = "ntsc", + .timings_type = VPBE_ENC_STD, + .std_id = V4L2_STD_NTSC, + .interlaced = 1, + .xres = 720, + .yres = 480, + .aspect = {11, 10}, + .fps = {30000, 1001}, + .left_margin = 0x79, + .upper_margin = 0x10, + }, + { + .name = "pal", + .timings_type = VPBE_ENC_STD, + .std_id = V4L2_STD_PAL, + .interlaced = 1, + .xres = 720, + .yres = 576, + .aspect = {54, 59}, + .fps = {25, 1}, + .left_margin = 0x7E, + .upper_margin = 0x16 + }, +}; + +#define VENC_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL) + +/* + * The outputs available from VPBE + ecnoders. Keep the + * the order same as that of encoders. First those from venc followed by that + * from encoders. Index in the output refers to index on a particular encoder. + * Driver uses this index to pass it to encoder when it supports more than + * one output. Application uses index of the array to set an output. + */ +static struct vpbe_output dm355evm_vpbe_outputs[] = { + { + .output = { + .index = 0, + .name = "Composite", + .type = V4L2_OUTPUT_TYPE_ANALOG, + .std = VENC_STD_ALL, + .capabilities = V4L2_OUT_CAP_STD, + }, + .subdev_name = DM355_VPBE_VENC_SUBDEV_NAME, + .default_mode = "ntsc", + .num_modes = ARRAY_SIZE(dm355evm_enc_preset_timing), + .modes = dm355evm_enc_preset_timing, + .if_params = V4L2_MBUS_FMT_FIXED, + }, +}; + +static struct vpbe_config dm355evm_display_cfg = { + .module_name = "dm355-vpbe-display", + .i2c_adapter_id = 1, + .osd = { + .module_name = DM355_VPBE_OSD_SUBDEV_NAME, + }, + .venc = { + .module_name = DM355_VPBE_VENC_SUBDEV_NAME, + }, + .num_outputs = ARRAY_SIZE(dm355evm_vpbe_outputs), + .outputs = dm355evm_vpbe_outputs, +}; + static struct platform_device *davinci_evm_devices[] __initdata = { &dm355evm_dm9000, &davinci_nand_device, }; -static struct davinci_uart_config uart_config __initdata = { - .enabled_uarts = (1 << 0), -}; - static void __init dm355_evm_map_io(void) { - /* setup input configuration for VPFE input devices */ - dm355_set_vpfe_config(&vpfe_cfg); dm355_init(); } @@ -279,7 +343,6 @@ static struct davinci_mmc_config dm355evm_mmc_config = { .wires = 4, .max_freq = 50000000, .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED, - .version = MMC_CTLR_VERSION_1, }; /* Don't connect anything to J10 unless you're only using USB host @@ -287,11 +350,7 @@ static struct davinci_mmc_config dm355evm_mmc_config = { * you have proper Mini-B or Mini-A cables (or Mini-A adapters) * the ID pin won't need any help. */ -#ifdef CONFIG_USB_MUSB_PERIPHERAL -#define USB_ID_VALUE 0 /* ID pulled high; *should* float */ -#else #define USB_ID_VALUE 1 /* ID pulled low */ -#endif static struct spi_eeprom at25640a = { .byte_len = SZ_64K / 8, @@ -314,6 +373,11 @@ static struct spi_board_info dm355_evm_spi_info[] __initconst = { static __init void dm355_evm_init(void) { struct clk *aemif; + int ret; + + ret = dm355_gpio_register(); + if (ret) + pr_warn("%s: GPIO init failed: %d\n", __func__, ret); gpio_request(1, "dm9000"); gpio_direction_input(1); @@ -323,12 +387,12 @@ static __init void dm355_evm_init(void) if (IS_ERR(aemif)) WARN("%s: unable to get AEMIF clock\n", __func__); else - clk_enable(aemif); + clk_prepare_enable(aemif); platform_add_devices(davinci_evm_devices, ARRAY_SIZE(davinci_evm_devices)); evm_init_i2c(); - davinci_serial_init(&uart_config); + davinci_serial_init(dm355_serial_device); /* NOTE: NAND flash timings set by the UBL are slower than * needed by MT29F16G08FAA chips ... EMIF.A1CR is 0x40400204 @@ -343,6 +407,8 @@ static __init void dm355_evm_init(void) davinci_setup_mmc(0, &dm355evm_mmc_config); davinci_setup_mmc(1, &dm355evm_mmc_config); + dm355_init_video(&vpfe_cfg, &dm355evm_display_cfg); + dm355_init_spi0(BIT(0), dm355_evm_spi_info, ARRAY_SIZE(dm355_evm_spi_info)); @@ -351,9 +417,12 @@ static __init void dm355_evm_init(void) } MACHINE_START(DAVINCI_DM355_EVM, "DaVinci DM355 EVM") - .boot_params = (0x80000100), + .atag_offset = 0x100, .map_io = dm355_evm_map_io, .init_irq = davinci_irq_init, - .timer = &davinci_timer, + .init_time = davinci_timer_init, .init_machine = dm355_evm_init, + .init_late = davinci_init_late, + .dma_zone_size = SZ_128M, + .restart = davinci_restart, MACHINE_END |