1 files changed, 121 insertions, 51 deletions

diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index 6c999dbd2bc..1ea61328f30 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -14,6 +14,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -23,11 +24,15 @@
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
 #include <linux/leds.h>
-#include <linux/clk.h>
 #include <linux/atmel-mci.h>
+#include <linux/delay.h>
+
+#include <linux/platform_data/at91_adc.h>
 
 #include <mach/hardware.h>
 #include <video/atmel_lcdc.h>
+#include <media/soc_camera.h>
+#include <media/atmel-isi.h>
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -37,43 +42,31 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
-#include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
 
+#include "at91_aic.h"
+#include "at91_shdwc.h"
+#include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
-static void __init ek_map_io(void)
+static void __init ek_init_early(void)
 {
 	/* Initialize processor: 12.000 MHz crystal */
-	at91sam9g45_initialize(12000000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 not connected on the -EK board */
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
+	at91_initialize(12000000);
 }
 
-static void __init ek_init_irq(void)
-{
-	at91sam9g45_init_interrupts(NULL);
-}
-
-
 /*
  * USB HS Host port (common to OHCI & EHCI)
  */
 static struct at91_usbh_data __initdata ek_usbh_hs_data = {
 	.ports		= 2,
 	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+	.vbus_pin_active_low = {1, 1},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -105,6 +98,7 @@ static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PD10,
+		.wp_pin		= -EINVAL,
 	},
 };
 
@@ -120,7 +114,7 @@ static struct mci_platform_data __initdata mci1_data = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PD5,
 	.is_rmii	= 1,
 };
@@ -142,24 +136,17 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 	},
 };
 
-static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-{
-	*num_partitions = ARRAY_SIZE(ek_nand_partition);
-	return ek_nand_partition;
-}
-
 /* det_pin is not connected */
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
-	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
+	.det_pin	= -EINVAL,
+	.ecc_mode	= NAND_ECC_SOFT,
+	.on_flash_bbt	= 1,
+	.parts		= ek_nand_partition,
+	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -182,6 +169,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 
 static void __init ek_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = board_have_nand_16bit();
 	/* setup bus-width (8 or 16) */
 	if (ek_nand_data.bus_width_16)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
@@ -189,13 +177,78 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
 
 
 /*
+ *  ISI
+ */
+static struct isi_platform_data __initdata isi_data = {
+	.frate			= ISI_CFG1_FRATE_CAPTURE_ALL,
+	/* to use codec and preview path simultaneously */
+	.full_mode		= 1,
+	.data_width_flags	= ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10,
+	/* ISI_MCK is provided by programmable clock or external clock */
+	.mck_hz			= 25000000,
+};
+
+
+/*
+ * soc-camera OV2640
+ */
+#if defined(CONFIG_SOC_CAMERA_OV2640) || \
+	defined(CONFIG_SOC_CAMERA_OV2640_MODULE)
+static unsigned long isi_camera_query_bus_param(struct soc_camera_link *link)
+{
+	/* ISI board for ek using default 8-bits connection */
+	return SOCAM_DATAWIDTH_8;
+}
+
+static int i2c_camera_power(struct device *dev, int on)
+{
+	/* enable or disable the camera */
+	pr_debug("%s: %s the camera\n", __func__, on ? "ENABLE" : "DISABLE");
+	at91_set_gpio_output(AT91_PIN_PD13, !on);
+
+	if (!on)
+		goto out;
+
+	/* If enabled, give a reset impulse */
+	at91_set_gpio_output(AT91_PIN_PD12, 0);
+	msleep(20);
+	at91_set_gpio_output(AT91_PIN_PD12, 1);
+	msleep(100);
+
+out:
+	return 0;
+}
+
+static struct i2c_board_info i2c_camera = {
+	I2C_BOARD_INFO("ov2640", 0x30),
+};
+
+static struct soc_camera_link iclink_ov2640 = {
+	.bus_id			= 0,
+	.board_info		= &i2c_camera,
+	.i2c_adapter_id		= 0,
+	.power			= i2c_camera_power,
+	.query_bus_param	= isi_camera_query_bus_param,
+};
+
+static struct platform_device isi_ov2640 = {
+	.name	= "soc-camera-pdrv",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &iclink_ov2640,
+	},
+};
+#endif
+
+
+/*
  * LCD Controller
  */
 #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
@@ -232,7 +285,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
 					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
 
 /* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
 	.lcdcon_is_backlight		= true,
 	.default_bpp			= 32,
 	.default_dmacon			= ATMEL_LCDC_DMAEN,
@@ -243,20 +296,20 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
 };
 
 #else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
 #endif
 
 
 /*
- * Touchscreen
+ * ADCs and touchscreen
  */
-static struct at91_tsadcc_data ek_tsadcc_data = {
-	.adc_clock		= 300000,
-	.pendet_debounce	= 0x0d,
-	.ts_sample_hold_time	= 0x0a,
+static struct at91_adc_data ek_adc_data = {
+	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7),
+	.use_external_triggers = true,
+	.vref = 3300,
+	.touchscreen_type = ATMEL_ADC_TOUCHSCREEN_4WIRE,
 };
 
-
 /*
  * GPIO Buttons
  */
@@ -344,6 +397,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 
@@ -387,11 +441,22 @@ static struct gpio_led ek_pwm_led[] = {
 #endif
 };
 
-
+static struct platform_device *devices[] __initdata = {
+#if defined(CONFIG_SOC_CAMERA_OV2640) || \
+	defined(CONFIG_SOC_CAMERA_OV2640_MODULE)
+	&isi_ov2640,
+#endif
+};
 
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 not connected on the -EK board */
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB HS Host */
 	at91_add_device_usbh_ohci(&ek_usbh_hs_data);
@@ -409,10 +474,12 @@ static void __init ek_board_init(void)
 	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(0, NULL, 0);
+	/* ISI, using programmable clock as ISI_MCK */
+	at91_add_device_isi(&isi_data, true);
 	/* LCD Controller */
 	at91_add_device_lcdc(&ek_lcdc_data);
-	/* Touch Screen */
-	at91_add_device_tsadcc(&ek_tsadcc_data);
+	/* ADC and touchscreen */
+	at91_add_device_adc(&ek_adc_data);
 	/* Push Buttons */
 	ek_add_device_buttons();
 	/* AC97 */
@@ -420,13 +487,16 @@ static void __init ek_board_init(void)
 	/* LEDs */
 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 	at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+	/* Other platform devices */
+	platform_add_devices(devices, ARRAY_SIZE(devices));
 }
 
 MACHINE_START(AT91SAM9M10G45EK, "Atmel AT91SAM9M10G45-EK")
 	/* Maintainer: Atmel */
-	.boot_params	= AT91_SDRAM_BASE + 0x100,
-	.timer		= &at91sam926x_timer,
-	.map_io		= ek_map_io,
-	.init_irq	= ek_init_irq,
+	.init_time	= at91sam926x_pit_init,
+	.map_io		= at91_map_io,
+	.handle_irq	= at91_aic_handle_irq,
+	.init_early	= ek_init_early,
+	.init_irq	= at91_init_irq_default,
 	.init_machine	= ek_board_init,
 MACHINE_END