diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9g20ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9g20ek.c | 213 |
1 files changed, 161 insertions, 52 deletions
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index c11fd47aec5..e1be6e25b38 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -18,6 +18,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -27,6 +28,11 @@ #include <linux/gpio_keys.h> #include <linux/input.h> #include <linux/clk.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> +#include <linux/regulator/consumer.h> + +#include <linux/platform_data/at91_adc.h> #include <mach/hardware.h> #include <asm/setup.h> @@ -37,45 +43,41 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91sam9_smc.h> +#include <mach/system_rev.h> +#include "at91_aic.h" +#include "board.h" #include "sam9_smc.h" #include "generic.h" +#include "gpio.h" - -static void __init ek_map_io(void) +/* + * board revision encoding + * bit 0: + * 0 => 1 sd/mmc slot + * 1 => 2 sd/mmc slots connectors (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static int inline ek_have_2mmc(void) { - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); + return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC); } -static void __init ek_init_irq(void) + +static void __init ek_init_early(void) { - at91sam9260_init_interrupts(NULL); + /* Initialize processor: 18.432 MHz crystal */ + at91_initialize(18432000); } - /* * USB Host port */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -83,7 +85,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -91,7 +93,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !IS_ENABLED(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -113,11 +115,18 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; +static void __init ek_add_device_macb(void) +{ + if (ek_have_2mmc()) + ek_macb_data.phy_irq_pin = AT91_PIN_PB0; + + at91_add_device_eth(&ek_macb_data); +} /* * NAND flash @@ -140,24 +149,17 @@ static struct mtd_partition __initdata ek_nand_partition[] = { }, }; -static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(ek_nand_partition); - return ek_nand_partition; -} - /* det_pin is not connected */ static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, - .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif + .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, + .parts = ek_nand_partition, + .num_parts = ARRAY_SIZE(ek_nand_partition), }; static struct sam9_smc_config __initdata ek_nand_smc_config = { @@ -180,6 +182,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { + ek_nand_data.bus_width_16 = board_have_nand_16bit(); /* setup bus-width (8 or 16) */ if (ek_nand_data.bus_width_16) ek_nand_smc_config.mode |= AT91_SMC_DBW_16; @@ -187,7 +190,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -195,13 +198,26 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected + * wp_pin and vcc_pin are not connected */ -static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, - .wire4 = 1, +static struct mci_platform_data __initdata ek_mmc_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, + }, + }; +static void __init ek_add_device_mmc(void) +{ + if (ek_have_2mmc()) { + ek_mmc_data.slot[0].bus_width = 4; + ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + ek_mmc_data.slot[0].wp_pin = -1; + } + at91_add_device_mci(0, &ek_mmc_data); +} /* * LEDs @@ -220,6 +236,15 @@ static struct gpio_led ek_leds[] = { } }; +static void __init ek_add_device_gpio_leds(void) +{ + if (ek_have_2mmc()) { + ek_leds[0].gpio = AT91_PIN_PB8; + ek_leds[1].gpio = AT91_PIN_PB9; + } + + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} /* * GPIO Buttons @@ -269,6 +294,56 @@ static void __init ek_add_device_buttons(void) static void __init ek_add_device_buttons(void) {} #endif +/* + * ADCs + */ + +static struct at91_adc_data ek_adc_data = { + .channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3), + .use_external_triggers = true, + .vref = 3300, +}; + +#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) +static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { + REGULATOR_SUPPLY("AVDD", "0-001b"), + REGULATOR_SUPPLY("HPVDD", "0-001b"), + REGULATOR_SUPPLY("DBVDD", "0-001b"), + REGULATOR_SUPPLY("DCVDD", "0-001b"), +}; + +static struct regulator_init_data ek_avdd_reg_init_data = { + .constraints = { + .name = "3V3", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .consumer_supplies = ek_audio_consumer_supplies, + .num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies), +}; + +static struct fixed_voltage_config ek_vdd_pdata = { + .supply_name = "board-3V3", + .microvolts = 3300000, + .gpio = -EINVAL, + .enabled_at_boot = 0, + .init_data = &ek_avdd_reg_init_data, +}; +static struct platform_device ek_voltage_regulator = { + .name = "reg-fixed-voltage", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_vdd_pdata, + }, +}; +static void __init ek_add_regulators(void) +{ + platform_device_register(&ek_voltage_regulator); +} +#else +static void __init ek_add_regulators(void) {} +#endif + static struct i2c_board_info __initdata ek_i2c_devices[] = { { @@ -279,10 +354,30 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = { }, }; +static struct platform_device sam9g20ek_audio_device = { + .name = "at91sam9g20ek-audio", + .id = -1, +}; + +static void __init ek_add_device_audio(void) +{ + platform_device_register(&sam9g20ek_audio_device); +} + static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); @@ -293,28 +388,42 @@ static void __init ek_board_init(void) /* NAND */ ek_add_device_nand(); /* Ethernet */ - at91_add_device_eth(&ek_macb_data); + ek_add_device_macb(); + /* Regulators */ + ek_add_regulators(); /* MMC */ - at91_add_device_mmc(0, &ek_mmc_data); + ek_add_device_mmc(); /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + ek_add_device_gpio_leds(); /* Push Buttons */ ek_add_device_buttons(); + /* ADCs */ + at91_add_device_adc(&ek_adc_data); /* PCK0 provides MCLK to the WM8731 */ at91_set_B_periph(AT91_PIN_PC1, 0); /* SSC (for WM8731) */ at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); + ek_add_device_audio(); } MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, + .init_time = at91sam926x_pit_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = ek_init_early, + .init_irq = at91_init_irq_default, + .init_machine = ek_board_init, +MACHINE_END + +MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") + /* Maintainer: Atmel */ + .init_time = at91sam926x_pit_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = ek_init_early, + .init_irq = at91_init_irq_default, .init_machine = ek_board_init, MACHINE_END |