1 files changed, 27 insertions, 26 deletions

diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index be8233bcabd..65dea12d685 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -28,7 +28,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/at73c213.h>
 #include <linux/clk.h>
-#include <linux/i2c/at24.h>
+#include <linux/platform_data/at24.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
 
@@ -41,33 +41,21 @@
 #include <asm/mach/irq.h>
 
 #include <mach/hardware.h>
-#include <mach/board.h>
 #include <mach/at91sam9_smc.h>
-#include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>
 
+#include "at91_aic.h"
+#include "at91_shdwc.h"
+#include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -121,7 +109,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
+#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -181,6 +169,8 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
+	.ecc_mode	= NAND_ECC_SOFT,
+	.on_flash_bbt	= 1,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -222,12 +212,12 @@ static void __init ek_add_device_nand(void)
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 
@@ -318,6 +308,16 @@ static void __init ek_add_device_buttons(void) {}
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
@@ -330,7 +330,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
 	/* SSC (to AT73C213) */
@@ -344,8 +344,9 @@ static void __init ek_board_init(void)
 
 MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
 	/* Maintainer: Atmel */
-	.timer		= &at91sam926x_timer,
+	.init_time	= at91sam926x_pit_init,
 	.map_io		= at91_map_io,
+	.handle_irq	= at91_aic_handle_irq,
 	.init_early	= ek_init_early,
 	.init_irq	= at91_init_irq_default,
 	.init_machine	= ek_board_init,