1 files changed, 43 insertions, 27 deletions

diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index e8b116b6cba..d24dda67e2d 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -37,34 +37,19 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/board.h>
 #include <mach/at91sam9_smc.h>
 
+#include "at91_aic.h"
+#include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -89,7 +74,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
+#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -174,17 +159,45 @@ static void __init ek_add_device_nand(void)
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PC8,
-	.wp_pin		= AT91_PIN_PC4,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PC8,
+		.wp_pin		= AT91_PIN_PC4,
+	},
+};
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+	{	/* D1 */
+		.name			= "led1",
+		.gpio			= AT91_PIN_PA9,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* D2 */
+		.name			= "led2",
+		.gpio			= AT91_PIN_PA6,
+		.active_low		= 1,
+		.default_trigger	= "timer",
+	}
 };
 
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
@@ -197,15 +210,18 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
+	/* LEDs */
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 }
 
 MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260")
 	/* Maintainer: Olimex */
-	.timer		= &at91sam926x_timer,
+	.init_time	= at91sam926x_pit_init,
 	.map_io		= at91_map_io,
+	.handle_irq	= at91_aic_handle_irq,
 	.init_early	= ek_init_early,
 	.init_irq	= at91_init_irq_default,
 	.init_machine	= ek_board_init,