1 files changed, 30 insertions, 35 deletions

diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index 9df1be8818c..953cea41675 100644
--- a/arch/arm/mach-at91/board-rm9200ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,45 +39,30 @@
 #include <asm/mach/irq.h>
 
 #include <mach/hardware.h>
-#include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
 
+#include "at91_aic.h"
+#include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
-static void __init ek_map_io(void)
+static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
-	at91rm9200_initialize(18432000, AT91RM9200_BGA);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
+	at91_initialize(18432000);
 }
 
-static void __init ek_init_irq(void)
-{
-	at91rm9200_init_interrupts(NULL);
-}
-
-static struct at91_eth_data __initdata ek_eth_data = {
+static struct macb_platform_data __initdata ek_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata ek_udc_data = {
@@ -85,11 +71,12 @@ static struct at91_udc_data __initdata ek_udc_data = {
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.det_pin	= AT91_PIN_PB27,
-	.slot_b		= 0,
-	.wire4		= 1,
-	.wp_pin		= AT91_PIN_PA17,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB27,
+		.wp_pin		= AT91_PIN_PA17,
+	}
 };
 #endif
 
@@ -118,7 +105,7 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = {
 };
 
 #define EK_FLASH_BASE	AT91_CHIPSELECT_0
-#define EK_FLASH_SIZE	SZ_2M
+#define EK_FLASH_SIZE	SZ_8M
 
 static struct physmap_flash_data ek_flash_data = {
 	.width		= 2,
@@ -163,6 +150,13 @@ static struct gpio_led ek_leds[] = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&ek_eth_data);
@@ -181,7 +175,7 @@ static void __init ek_board_init(void)
 #else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 #endif
 	/* NOR Flash */
 	platform_device_register(&ek_flash);
@@ -193,9 +187,10 @@ static void __init ek_board_init(void)
 
 MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
 	/* Maintainer: SAN People/Atmel */
-	.boot_params	= AT91_SDRAM_BASE + 0x100,
-	.timer		= &at91rm9200_timer,
-	.map_io		= ek_map_io,
-	.init_irq	= ek_init_irq,
+	.init_time	= at91rm9200_timer_init,
+	.map_io		= at91_map_io,
+	.handle_irq	= at91_aic_handle_irq,
+	.init_early	= ek_init_early,
+	.init_irq	= at91_init_irq_default,
 	.init_machine	= ek_board_init,
 MACHINE_END