diff options
Diffstat (limited to 'arch/arm/mach-at91/board-foxg20.c')
| -rw-r--r-- | arch/arm/mach-at91/board-foxg20.c | 95 |
1 files changed, 47 insertions, 48 deletions
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index caf017f0f4e..8b22c60bb23 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -41,11 +41,13 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <mach/board.h> #include <mach/at91sam9_smc.h> +#include "at91_aic.h" +#include "board.h" #include "sam9_smc.h" #include "generic.h" +#include "gpio.h" /* * The FOX Board G20 hardware comes as the "Netus G20" board with @@ -61,44 +63,6 @@ static void __init foxg20_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS - | ATMEL_UART_RTS - | ATMEL_UART_DTR - | ATMEL_UART_DSR - | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, 0); - - /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); - - /* Set the internal pull-up resistor on DRXD */ - at91_set_A_periph(AT91_PIN_PB14, 1); - } /* @@ -123,7 +87,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = { * SPI devices. */ static struct spi_board_info foxg20_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !IS_ENABLED(CONFIG_MMC_ATMELMCI) { .modalias = "mtd_dataflash", .chip_select = 1, @@ -146,12 +110,12 @@ static struct macb_platform_data __initdata foxg20_macb_data = { * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected */ -static struct at91_mmc_data __initdata foxg20_mmc_data = { - .slot_b = 1, - .wire4 = 1, - .det_pin = -EINVAL, - .wp_pin = -EINVAL, - .vcc_pin = -EINVAL, +static struct mci_platform_data __initdata foxg20_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, }; @@ -213,6 +177,7 @@ static struct w1_gpio_platform_data w1_gpio_pdata = { /* If you choose to use a pin other than PB16 it needs to be 3.3V */ .pin = AT91_PIN_PB16, .is_open_drain = 1, + .ext_pullup_enable_pin = -EINVAL, }; static struct platform_device w1_device = { @@ -241,6 +206,39 @@ static struct i2c_board_info __initdata foxg20_i2c_devices[] = { static void __init foxg20_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS + | ATMEL_UART_RTS + | ATMEL_UART_DTR + | ATMEL_UART_DSR + | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); + + /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); + + /* Set the internal pull-up resistor on DRXD */ + at91_set_A_periph(AT91_PIN_PB14, 1); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&foxg20_usbh_data); @@ -251,7 +249,7 @@ static void __init foxg20_board_init(void) /* Ethernet */ at91_add_device_eth(&foxg20_macb_data); /* MMC */ - at91_add_device_mmc(0, &foxg20_mmc_data); + at91_add_device_mci(0, &foxg20_mci0_data); /* I2C */ at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); /* LEDs */ @@ -265,8 +263,9 @@ static void __init foxg20_board_init(void) MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20") /* Maintainer: Sergio Tanzilli */ - .timer = &at91sam926x_timer, + .init_time = at91sam926x_pit_init, .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, .init_early = foxg20_init_early, .init_irq = at91_init_irq_default, .init_machine = foxg20_board_init, |