1 files changed, 0 insertions, 124 deletions
diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c
deleted file mode 100644
index bb6b434ec0c..00000000000
--- a/arch/arm/mach-at91/board-dt.c
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- *  Setup code for AT91SAM Evaluation Kits with Device Tree support
- *
- *  Covers: * AT91SAM9G45-EKES  board
- *          * AT91SAM9M10-EKES  board
- *          * AT91SAM9M10G45-EK board
- *
- *  Copyright (C) 2011 Atmel,
- *                2011 Nicolas Ferre <nicolas.ferre@atmel.com>
- *
- * Licensed under GPLv2 or later.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/gpio.h>
-#include <linux/irqdomain.h>
-#include <linux/of_irq.h>
-#include <linux/of_platform.h>
-
-#include <mach/hardware.h>
-#include <mach/board.h>
-#include <mach/system_rev.h>
-#include <mach/at91sam9_smc.h>
-
-#include <asm/setup.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 12.000 MHz crystal */
-	at91_initialize(12000000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-/* det_pin is not connected */
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC8,
-	.enable_pin	= AT91_PIN_PC14,
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 3,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-static const struct of_device_id aic_of_match[] __initconst = {
-	{ .compatible = "atmel,at91rm9200-aic", },
-	{},
-};
-
-static void __init at91_dt_init_irq(void)
-{
-	irq_domain_generate_simple(aic_of_match, 0xfffff000, 0);
-	at91_init_irq_default();
-}
-
-static void __init at91_dt_device_init(void)
-{
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-
-	/* NAND */
-	ek_add_device_nand();
-}
-
-static const char *at91_dt_board_compat[] __initdata = {
-	"atmel,at91sam9m10g45ek",
-	"calao,usb-a9g20",
-	NULL
-};
-
-DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM (Device Tree)")
-	/* Maintainer: Atmel */
-	.timer		= &at91sam926x_timer,
-	.map_io		= at91_map_io,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_dt_init_irq,
-	.init_machine	= at91_dt_device_init,
-	.dt_compat	= at91_dt_board_compat,
-MACHINE_END