diff options
Diffstat (limited to 'arch/arm/mach-at91/board-cpu9krea.c')
| -rw-r--r-- | arch/arm/mach-at91/board-cpu9krea.c | 82 |
1 files changed, 41 insertions, 41 deletions
diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 9ab3d1ea326..2037f78c84e 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -40,45 +40,20 @@ #include <asm/mach/irq.h> #include <mach/hardware.h> -#include <mach/board.h> #include <mach/at91sam9_smc.h> #include <mach/at91sam9260_matrix.h> +#include <mach/at91_matrix.h> +#include "at91_aic.h" +#include "board.h" #include "sam9_smc.h" #include "generic.h" +#include "gpio.h" static void __init cpu9krea_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | - ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART3 on ttyS4. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, 0); - - /* USART4 on ttyS5. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } /* @@ -116,6 +91,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = { .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, }; #ifdef CONFIG_MACH_CPU9260 @@ -238,8 +214,8 @@ static __init void cpu9krea_add_device_nor(void) { unsigned long csa; - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V); + csa = at91_matrix_read(AT91_MATRIX_EBICSA); + at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V); /* configure chip-select 0 (NOR) */ sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config); @@ -279,8 +255,7 @@ static struct gpio_led cpu9krea_leds[] = { static struct i2c_board_info __initdata cpu9krea_i2c_devices[] = { { - I2C_BOARD_INFO("rtc-ds1307", 0x68), - .type = "ds1339", + I2C_BOARD_INFO("ds1339", 0x68), }, }; @@ -337,12 +312,12 @@ static void __init cpu9krea_add_device_buttons(void) /* * MCI (SD/MMC) */ -static struct at91_mmc_data __initdata cpu9krea_mmc_data = { - .slot_b = 0, - .wire4 = 1, - .det_pin = AT91_PIN_PA29, - .wp_pin = -EINVAL, - .vcc_pin = -EINVAL, +static struct mci_platform_data __initdata cpu9krea_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PA29, + .wp_pin = -EINVAL, + }, }; static void __init cpu9krea_board_init(void) @@ -350,6 +325,30 @@ static void __init cpu9krea_board_init(void) /* NOR */ cpu9krea_add_device_nor(); /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART3 on ttyS4. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, 0); + + /* USART4 on ttyS5. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&cpu9krea_usbh_data); @@ -360,7 +359,7 @@ static void __init cpu9krea_board_init(void) /* Ethernet */ at91_add_device_eth(&cpu9krea_macb_data); /* MMC */ - at91_add_device_mmc(0, &cpu9krea_mmc_data); + at91_add_device_mci(0, &cpu9krea_mci0_data); /* I2C */ at91_add_device_i2c(cpu9krea_i2c_devices, ARRAY_SIZE(cpu9krea_i2c_devices)); @@ -376,8 +375,9 @@ MACHINE_START(CPUAT9260, "Eukrea CPU9260") MACHINE_START(CPUAT9G20, "Eukrea CPU9G20") #endif /* Maintainer: Eric Benard - EUKREA Electromatique */ - .timer = &at91sam926x_timer, + .init_time = at91sam926x_pit_init, .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, .init_early = cpu9krea_init_early, .init_irq = at91_init_irq_default, .init_machine = cpu9krea_board_init, |