diff options
Diffstat (limited to 'arch/arm/boot/dts/phy3250.dts')
| -rw-r--r-- | arch/arm/boot/dts/phy3250.dts | 71 |
1 files changed, 64 insertions, 7 deletions
diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts index c4ff6d1a018..90fdbd77f27 100644 --- a/arch/arm/boot/dts/phy3250.dts +++ b/arch/arm/boot/dts/phy3250.dts @@ -54,6 +54,17 @@ #address-cells = <1>; #size-cells = <1>; + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + mtd0@00000000 { label = "phy3250-boot"; reg = <0x00000000 0x00064000>; @@ -83,6 +94,14 @@ }; apb { + uart5: serial@40090000 { + status = "okay"; + }; + + uart3: serial@40080000 { + status = "okay"; + }; + i2c1: i2c@400A0000 { clock-frequency = <100000>; @@ -114,32 +133,70 @@ }; ssp0: ssp@20084000 { + #address-cells = <1>; + #size-cells = <0>; + num-cs = <1>; + cs-gpios = <&gpio 3 5 0>; + eeprom: at25@0 { + pl022,interface = <0>; + pl022,com-mode = <0>; + pl022,rx-level-trig = <1>; + pl022,tx-level-trig = <1>; + pl022,ctrl-len = <11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + + at25,byte-len = <0x8000>; + at25,addr-mode = <2>; + at25,page-size = <64>; + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; }; }; + + sd@20098000 { + wp-gpios = <&gpio 3 0 0>; + cd-gpios = <&gpio 3 1 0>; + cd-inverted; + bus-width = <4>; + status = "okay"; + }; }; fab { + uart2: serial@40018000 { + status = "okay"; + }; + tsc@40048000 { status = "okay"; }; + + key@40050000 { + status = "okay"; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; }; }; leds { compatible = "gpio-leds"; - led0 { - gpios = <&gpio 5 1 1>; /* GPO_P3 1, GPIO 80, active low */ - linux,default-trigger = "heartbeat"; + led0 { /* red */ + gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */ default-state = "off"; }; - led1 { - gpios = <&gpio 5 14 1>; /* GPO_P3 14, GPIO 93, active low */ - linux,default-trigger = "timer"; - default-state = "off"; + led1 { /* green */ + gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */ + linux,default-trigger = "heartbeat"; }; }; }; |