diff options
Diffstat (limited to 'Documentation/usb')
| -rw-r--r-- | Documentation/usb/URB.txt | 21 | ||||
| -rw-r--r-- | Documentation/usb/WUSB-Design-overview.txt | 2 | ||||
| -rw-r--r-- | Documentation/usb/chipidea.txt | 71 | ||||
| -rw-r--r-- | Documentation/usb/gadget_configfs.txt | 384 | ||||
| -rw-r--r-- | Documentation/usb/gadget_multi.txt | 2 | ||||
| -rw-r--r-- | Documentation/usb/hotplug.txt | 6 | ||||
| -rw-r--r-- | Documentation/usb/mass-storage.txt | 2 | ||||
| -rw-r--r-- | Documentation/usb/power-management.txt | 10 | ||||
| -rw-r--r-- | Documentation/usb/proc_usb_info.txt | 9 |
9 files changed, 483 insertions, 24 deletions
diff --git a/Documentation/usb/URB.txt b/Documentation/usb/URB.txt index 00d2c644068..50da0d45544 100644 --- a/Documentation/usb/URB.txt +++ b/Documentation/usb/URB.txt @@ -195,13 +195,12 @@ by the completion handler. The handler is of the following type: - typedef void (*usb_complete_t)(struct urb *, struct pt_regs *) + typedef void (*usb_complete_t)(struct urb *) -I.e., it gets the URB that caused the completion call, plus the -register values at the time of the corresponding interrupt (if any). -In the completion handler, you should have a look at urb->status to -detect any USB errors. Since the context parameter is included in the URB, -you can pass information to the completion handler. +I.e., it gets the URB that caused the completion call. In the completion +handler, you should have a look at urb->status to detect any USB errors. +Since the context parameter is included in the URB, you can pass +information to the completion handler. Note that even when an error (or unlink) is reported, data may have been transferred. That's because USB transfers are packetized; it might take @@ -210,12 +209,12 @@ have transferred successfully before the completion was called. NOTE: ***** WARNING ***** -NEVER SLEEP IN A COMPLETION HANDLER. These are normally called -during hardware interrupt processing. If you can, defer substantial -work to a tasklet (bottom half) to keep system latencies low. You'll -probably need to use spinlocks to protect data structures you manipulate -in completion handlers. +NEVER SLEEP IN A COMPLETION HANDLER. These are often called in atomic +context. +In the current kernel, completion handlers run with local interrupts +disabled, but in the future this will be changed, so don't assume that +local IRQs are always disabled inside completion handlers. 1.8. How to do isochronous (ISO) transfers? diff --git a/Documentation/usb/WUSB-Design-overview.txt b/Documentation/usb/WUSB-Design-overview.txt index 4c5e3793934..1cd07c017cf 100644 --- a/Documentation/usb/WUSB-Design-overview.txt +++ b/Documentation/usb/WUSB-Design-overview.txt @@ -25,7 +25,7 @@ updated content. * Design-overview.txt-1.8 This code implements a Ultra Wide Band stack for Linux, as well as -drivers for the the USB based UWB radio controllers defined in the +drivers for the USB based UWB radio controllers defined in the Wireless USB 1.0 specification (including Wireless USB host controller and an Intel WiNET controller). diff --git a/Documentation/usb/chipidea.txt b/Documentation/usb/chipidea.txt new file mode 100644 index 00000000000..995c8bca40e --- /dev/null +++ b/Documentation/usb/chipidea.txt @@ -0,0 +1,71 @@ +1. How to test OTG FSM(HNP and SRP) +----------------------------------- +To show how to demo OTG HNP and SRP functions via sys input files +with 2 Freescale i.MX6Q sabre SD boards. + +1.1 How to enable OTG FSM in menuconfig +--------------------------------------- +Select CONFIG_USB_OTG_FSM, rebuild kernel Image and modules. +If you want to check some internal variables for otg fsm, +select CONFIG_USB_CHIPIDEA_DEBUG, there are 2 files which +can show otg fsm variables and some controller registers value: +cat /sys/kernel/debug/ci_hdrc.0/otg +cat /sys/kernel/debug/ci_hdrc.0/registers + +1.2 Test operations +------------------- +1) Power up 2 Freescale i.MX6Q sabre SD boards with gadget class driver loaded + (e.g. g_mass_storage). + +2) Connect 2 boards with usb cable with one end is micro A plug, the other end + is micro B plug. + + The A-device(with micro A plug inserted) should enumrate B-device. + +3) Role switch + On B-device: + echo 1 > /sys/bus/platform/devices/ci_hdrc.0/inputs/b_bus_req + + if HNP polling is not supported, also need: + On A-device: + echo 0 > /sys/bus/platform/devices/ci_hdrc.0/inputs/a_bus_req + + B-device should take host role and enumrate A-device. + +4) A-device switch back to host. + On B-device: + echo 0 > /sys/bus/platform/devices/ci_hdrc.0/inputs/b_bus_req + + A-device should switch back to host and enumrate B-device. + +5) Remove B-device(unplug micro B plug) and insert again in 10 seconds, + A-device should enumrate B-device again. + +6) Remove B-device(unplug micro B plug) and insert again after 10 seconds, + A-device should NOT enumrate B-device. + + if A-device wants to use bus: + On A-device: + echo 0 > /sys/bus/platform/devices/ci_hdrc.0/inputs/a_bus_drop + echo 1 > /sys/bus/platform/devices/ci_hdrc.0/inputs/a_bus_req + + if B-device wants to use bus: + On B-device: + echo 1 > /sys/bus/platform/devices/ci_hdrc.0/inputs/b_bus_req + +7) A-device power down the bus. + On A-device: + echo 1 > /sys/bus/platform/devices/ci_hdrc.0/inputs/a_bus_drop + + A-device should disconnect with B-device and power down the bus. + +8) B-device does data pulse for SRP. + On B-device: + echo 1 > /sys/bus/platform/devices/ci_hdrc.0/inputs/b_bus_req + + A-device should resume usb bus and enumrate B-device. + +1.3 Reference document +---------------------- +"On-The-Go and Embedded Host Supplement to the USB Revision 2.0 Specification +July 27, 2012 Revision 2.0 version 1.1a" diff --git a/Documentation/usb/gadget_configfs.txt b/Documentation/usb/gadget_configfs.txt new file mode 100644 index 00000000000..4cf53e40661 --- /dev/null +++ b/Documentation/usb/gadget_configfs.txt @@ -0,0 +1,384 @@ + + + + + Linux USB gadget configured through configfs + + + 25th April 2013 + + + + +Overview +======== + +A USB Linux Gadget is a device which has a UDC (USB Device Controller) and can +be connected to a USB Host to extend it with additional functions like a serial +port or a mass storage capability. + +A gadget is seen by its host as a set of configurations, each of which contains +a number of interfaces which, from the gadget's perspective, are known as +functions, each function representing e.g. a serial connection or a SCSI disk. + +Linux provides a number of functions for gadgets to use. + +Creating a gadget means deciding what configurations there will be +and which functions each configuration will provide. + +Configfs (please see Documentation/filesystems/configfs/*) lends itself nicely +for the purpose of telling the kernel about the above mentioned decision. +This document is about how to do it. + +It also describes how configfs integration into gadget is designed. + + + + +Requirements +============ + +In order for this to work configfs must be available, so CONFIGFS_FS must be +'y' or 'm' in .config. As of this writing USB_LIBCOMPOSITE selects CONFIGFS_FS. + + + + +Usage +===== + +(The original post describing the first function +made available through configfs can be seen here: +http://www.spinics.net/lists/linux-usb/msg76388.html) + +$ modprobe libcomposite +$ mount none $CONFIGFS_HOME -t configfs + +where CONFIGFS_HOME is the mount point for configfs + +1. Creating the gadgets +----------------------- + +For each gadget to be created its corresponding directory must be created: + +$ mkdir $CONFIGFS_HOME/usb_gadget/<gadget name> + +e.g.: + +$ mkdir $CONFIGFS_HOME/usb_gadget/g1 + +... +... +... + +$ cd $CONFIGFS_HOME/usb_gadget/g1 + +Each gadget needs to have its vendor id <VID> and product id <PID> specified: + +$ echo <VID> > idVendor +$ echo <PID> > idProduct + +A gadget also needs its serial number, manufacturer and product strings. +In order to have a place to store them, a strings subdirectory must be created +for each language, e.g.: + +$ mkdir strings/0x409 + +Then the strings can be specified: + +$ echo <serial number> > strings/0x409/serialnumber +$ echo <manufacturer> > strings/0x409/manufacturer +$ echo <product> > strings/0x409/product + +2. Creating the configurations +------------------------------ + +Each gadget will consist of a number of configurations, their corresponding +directories must be created: + +$ mkdir configs/<name>.<number> + +where <name> can be any string which is legal in a filesystem and the +<number> is the configuration's number, e.g.: + +$ mkdir configs/c.1 + +... +... +... + +Each configuration also needs its strings, so a subdirectory must be created +for each language, e.g.: + +$ mkdir configs/c.1/strings/0x409 + +Then the configuration string can be specified: + +$ echo <configuration> > configs/c.1/strings/0x409/configuration + +Some attributes can also be set for a configuration, e.g.: + +$ echo 120 > configs/c.1/MaxPower + +3. Creating the functions +------------------------- + +The gadget will provide some functions, for each function its corresponding +directory must be created: + +$ mkdir functions/<name>.<instance name> + +where <name> corresponds to one of allowed function names and instance name +is an arbitrary string allowed in a filesystem, e.g.: + +$ mkdir functions/ncm.usb0 # usb_f_ncm.ko gets loaded with request_module() + +... +... +... + +Each function provides its specific set of attributes, with either read-only +or read-write access. Where applicable they need to be written to as +appropriate. +Please refer to Documentation/ABI/*/configfs-usb-gadget* for more information. + +4. Associating the functions with their configurations +------------------------------------------------------ + +At this moment a number of gadgets is created, each of which has a number of +configurations specified and a number of functions available. What remains +is specifying which function is available in which configuration (the same +function can be used in multiple configurations). This is achieved with +creating symbolic links: + +$ ln -s functions/<name>.<instance name> configs/<name>.<number> + +e.g.: + +$ ln -s functions/ncm.usb0 configs/c.1 + +... +... +... + +5. Enabling the gadget +---------------------- + +All the above steps serve the purpose of composing the gadget of +configurations and functions. + +An example directory structure might look like this: + +. +./strings +./strings/0x409 +./strings/0x409/serialnumber +./strings/0x409/product +./strings/0x409/manufacturer +./configs +./configs/c.1 +./configs/c.1/ncm.usb0 -> ../../../../usb_gadget/g1/functions/ncm.usb0 +./configs/c.1/strings +./configs/c.1/strings/0x409 +./configs/c.1/strings/0x409/configuration +./configs/c.1/bmAttributes +./configs/c.1/MaxPower +./functions +./functions/ncm.usb0 +./functions/ncm.usb0/ifname +./functions/ncm.usb0/qmult +./functions/ncm.usb0/host_addr +./functions/ncm.usb0/dev_addr +./UDC +./bcdUSB +./bcdDevice +./idProduct +./idVendor +./bMaxPacketSize0 +./bDeviceProtocol +./bDeviceSubClass +./bDeviceClass + + +Such a gadget must be finally enabled so that the USB host can enumerate it. +In order to enable the gadget it must be bound to a UDC (USB Device Controller). + +$ echo <udc name> > UDC + +where <udc name> is one of those found in /sys/class/udc/* +e.g.: + +$ echo s3c-hsotg > UDC + + +6. Disabling the gadget +----------------------- + +$ echo "" > UDC + +7. Cleaning up +-------------- + +Remove functions from configurations: + +$ rm configs/<config name>.<number>/<function> + +where <config name>.<number> specify the configuration and <function> is +a symlink to a function being removed from the configuration, e.g.: + +$ rm configfs/c.1/ncm.usb0 + +... +... +... + +Remove strings directories in configurations + +$ rmdir configs/<config name>.<number>/strings/<lang> + +e.g.: + +$ rmdir configs/c.1/strings/0x409 + +... +... +... + +and remove the configurations + +$ rmdir configs/<config name>.<number> + +e.g.: + +rmdir configs/c.1 + +... +... +... + +Remove functions (function modules are not unloaded, though) + +$ rmdir functions/<name>.<instance name> + +e.g.: + +$ rmdir functions/ncm.usb0 + +... +... +... + +Remove strings directories in the gadget + +$ rmdir strings/<lang> + +e.g.: + +$ rmdir strings/0x409 + +and finally remove the gadget: + +$ cd .. +$ rmdir <gadget name> + +e.g.: + +$ rmdir g1 + + + + +Implementation design +===================== + +Below the idea of how configfs works is presented. +In configfs there are items and groups, both represented as directories. +The difference between an item and a group is that a group can contain +other groups. In the picture below only an item is shown. +Both items and groups can have attributes, which are represented as files. +The user can create and remove directories, but cannot remove files, +which can be read-only or read-write, depending on what they represent. + +The filesystem part of configfs operates on config_items/groups and +configfs_attributes which are generic and of the same type for all +configured elements. However, they are embedded in usage-specific +larger structures. In the picture below there is a "cs" which contains +a config_item and an "sa" which contains a configfs_attribute. + +The filesystem view would be like this: + +./ +./cs (directory) + | + +--sa (file) + | + . + . + . + +Whenever a user reads/writes the "sa" file, a function is called +which accepts a struct config_item and a struct configfs_attribute. +In the said function the "cs" and "sa" are retrieved using the well +known container_of technique and an appropriate sa's function (show or +store) is called and passed the "cs" and a character buffer. The "show" +is for displaying the file's contents (copy data from the cs to the +buffer), while the "store" is for modifying the file's contents (copy data +from the buffer to the cs), but it is up to the implementer of the +two functions to decide what they actually do. + +typedef struct configured_structure cs; +typedef struct specific_attribute sa; + + sa + +----------------------------------+ + cs | (*show)(cs *, buffer); | ++-----------------+ | (*store)(cs *, buffer, length); | +| | | | +| +-------------+ | | +------------------+ | +| | struct |-|----|------>|struct | | +| | config_item | | | |configfs_attribute| | +| +-------------+ | | +------------------+ | +| | +----------------------------------+ +| data to be set | . +| | . ++-----------------+ . + +The file names are decided by the config item/group designer, while +the directories in general can be named at will. A group can have +a number of its default sub-groups created automatically. + +For more information on configfs please see +Documentation/filesystems/configfs/*. + +The concepts described above translate to USB gadgets like this: + +1. A gadget has its config group, which has some attributes (idVendor, +idProduct etc) and default sub-groups (configs, functions, strings). +Writing to the attributes causes the information to be stored in +appropriate locations. In the configs, functions and strings sub-groups +a user can create their sub-groups to represent configurations, functions, +and groups of strings in a given language. + +2. The user creates configurations and functions, in the configurations +creates symbolic links to functions. This information is used when the +gadget's UDC attribute is written to, which means binding the gadget +to the UDC. The code in drivers/usb/gadget/configfs.c iterates over +all configurations, and in each configuration it iterates over all +functions and binds them. This way the whole gadget is bound. + +3. The file drivers/usb/gadget/configfs.c contains code for + + - gadget's config_group + - gadget's default groups (configs, functions, strings) + - associating functions with configurations (symlinks) + +4. Each USB function naturally has its own view of what it wants +configured, so config_groups for particular functions are defined +in the functions implementation files drivers/usb/gadget/f_*.c. + +5. Funciton's code is written in such a way that it uses + +usb_get_function_instance(), which, in turn, calls request_module. +So, provided that modprobe works, modules for particular functions +are loaded automatically. Please note that the converse is not true: +after a gadget is disabled and torn down, the modules remain loaded. diff --git a/Documentation/usb/gadget_multi.txt b/Documentation/usb/gadget_multi.txt index 80f4ef0eb75..7d66a8636cb 100644 --- a/Documentation/usb/gadget_multi.txt +++ b/Documentation/usb/gadget_multi.txt @@ -14,7 +14,7 @@ A CDC ECM (Ethernet) function may be turned on via a Kconfig option and RNDIS can be turned off. If they are both enabled the gadget will have two configurations -- one with RNDIS and another with CDC ECM[3]. -Please not that if you use non-standard configuration (that is enable +Please note that if you use non-standard configuration (that is enable CDC ECM) you may need to change vendor and/or product ID. * Host drivers diff --git a/Documentation/usb/hotplug.txt b/Documentation/usb/hotplug.txt index 4c945716a66..6424b130485 100644 --- a/Documentation/usb/hotplug.txt +++ b/Documentation/usb/hotplug.txt @@ -33,9 +33,9 @@ you get the best hotplugging when you configure a highly modular system. KERNEL HOTPLUG HELPER (/sbin/hotplug) -When you compile with CONFIG_HOTPLUG, you get a new kernel parameter: -/proc/sys/kernel/hotplug, which normally holds the pathname "/sbin/hotplug". -That parameter names a program which the kernel may invoke at various times. +There is a kernel parameter: /proc/sys/kernel/hotplug, which normally +holds the pathname "/sbin/hotplug". That parameter names a program +which the kernel may invoke at various times. The /sbin/hotplug program can be invoked by any subsystem as part of its reaction to a configuration change, from a thread in that subsystem. diff --git a/Documentation/usb/mass-storage.txt b/Documentation/usb/mass-storage.txt index 59063ad7a60..e89803a5a96 100644 --- a/Documentation/usb/mass-storage.txt +++ b/Documentation/usb/mass-storage.txt @@ -13,7 +13,7 @@ operation. Note that the driver is slightly non-portable in that it assumes - a single memory/DMA buffer will be useable for bulk-in and bulk-out + a single memory/DMA buffer will be usable for bulk-in and bulk-out endpoints. With most device controllers this is not an issue, but there may be some with hardware restrictions that prevent a buffer from being used by more than one endpoint. diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt index 4204eb01fd3..1392b61d6eb 100644 --- a/Documentation/usb/power-management.txt +++ b/Documentation/usb/power-management.txt @@ -33,6 +33,10 @@ built with CONFIG_USB_SUSPEND enabled (which depends on CONFIG_PM_RUNTIME). System PM support is present only if the kernel was built with CONFIG_SUSPEND or CONFIG_HIBERNATION enabled. +(Starting with the 3.10 kernel release, dynamic PM support for USB is +present whenever the kernel was built with CONFIG_PM_RUNTIME enabled. +The CONFIG_USB_SUSPEND option has been eliminated.) + What is Remote Wakeup? ---------------------- @@ -206,10 +210,8 @@ initialized to 5. (The idle-delay values for already existing devices will not be affected.) Setting the initial default idle-delay to -1 will prevent any -autosuspend of any USB device. This is a simple alternative to -disabling CONFIG_USB_SUSPEND and rebuilding the kernel, and it has the -added benefit of allowing you to enable autosuspend for selected -devices. +autosuspend of any USB device. This has the benefit of allowing you +then to enable autosuspend for selected devices. Warnings diff --git a/Documentation/usb/proc_usb_info.txt b/Documentation/usb/proc_usb_info.txt index c9c3f0f5ad7..98be9198267 100644 --- a/Documentation/usb/proc_usb_info.txt +++ b/Documentation/usb/proc_usb_info.txt @@ -54,9 +54,12 @@ it and 002/048 sometime later. These files can be read as binary data. The binary data consists of first the device descriptor, then the descriptors for each -configuration of the device. Multi-byte fields in the device and -configuration descriptors, but not other descriptors, are converted -to host endianness by the kernel. This information is also shown +configuration of the device. Multi-byte fields in the device descriptor +are converted to host endianness by the kernel. The configuration +descriptors are in bus endian format! The configuration descriptor +are wTotalLength bytes apart. If a device returns less configuration +descriptor data than indicated by wTotalLength there will be a hole in +the file for the missing bytes. This information is also shown in text form by the /proc/bus/usb/devices file, described later. These files may also be used to write user-level drivers for the USB |