diff options
Diffstat (limited to 'Documentation/spi/spi-summary')
| -rw-r--r-- | Documentation/spi/spi-summary | 85 |
1 files changed, 67 insertions, 18 deletions
diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary index 4884cb33845..7982bcc4d15 100644 --- a/Documentation/spi/spi-summary +++ b/Documentation/spi/spi-summary @@ -1,7 +1,7 @@ Overview of Linux kernel SPI support ==================================== -21-May-2007 +02-Feb-2012 What is SPI? ------------ @@ -34,7 +34,7 @@ SPI slave functions are usually not interoperable between vendors - It may also be used to stream data in either direction (half duplex), or both of them at the same time (full duplex). - - Some devices may use eight bit words. Others may different word + - Some devices may use eight bit words. Others may use different word lengths, such as streams of 12-bit or 20-bit digital samples. - Words are usually sent with their most significant bit (MSB) first, @@ -121,7 +121,7 @@ active. So the master must set the clock to inactive before selecting a slave, and the slave can tell the chosen polarity by sampling the clock level when its select line goes active. That's why many devices support for example both modes 0 and 3: they don't care about polarity, -and alway clock data in/out on rising clock edges. +and always clock data in/out on rising clock edges. How do these driver programming interfaces work? @@ -139,7 +139,7 @@ a command and then reading its response. There are two types of SPI driver, here called: - Controller drivers ... controllers may be built in to System-On-Chip + Controller drivers ... controllers may be built into System-On-Chip processors, and often support both Master and Slave roles. These drivers touch hardware registers and may use DMA. Or they can be PIO bitbangers, needing just GPIO pins. @@ -215,7 +215,7 @@ So for example arch/.../mach-*/board-*.c files might have code like: /* if your mach-* infrastructure doesn't support kernels that can * run on multiple boards, pdata wouldn't benefit from "__init". */ - static struct mysoc_spi_data __initdata pdata = { ... }; + static struct mysoc_spi_data pdata __initdata = { ... }; static __init board_init(void) { @@ -345,7 +345,7 @@ SPI protocol drivers somewhat resemble platform device drivers: }, .probe = CHIP_probe, - .remove = __devexit_p(CHIP_remove), + .remove = CHIP_remove, .suspend = CHIP_suspend, .resume = CHIP_resume, }; @@ -355,7 +355,7 @@ device whose board_info gave a modalias of "CHIP". Your probe() code might look like this unless you're creating a device which is managing a bus (appearing under /sys/class/spi_master). - static int __devinit CHIP_probe(struct spi_device *spi) + static int CHIP_probe(struct spi_device *spi) { struct CHIP *chip; struct CHIP_platform_data *pdata; @@ -483,9 +483,9 @@ also initialize its own internal state. (See below about bus numbering and those methods.) After you initialize the spi_master, then use spi_register_master() to -publish it to the rest of the system. At that time, device nodes for -the controller and any predeclared spi devices will be made available, -and the driver model core will take care of binding them to drivers. +publish it to the rest of the system. At that time, device nodes for the +controller and any predeclared spi devices will be made available, and +the driver model core will take care of binding them to drivers. If you need to remove your SPI controller driver, spi_unregister_master() will reverse the effect of spi_register_master(). @@ -521,21 +521,68 @@ SPI MASTER METHODS ** When you code setup(), ASSUME that the controller ** is actively processing transfers for another device. - master->transfer(struct spi_device *spi, struct spi_message *message) - This must not sleep. Its responsibility is arrange that the - transfer happens and its complete() callback is issued. The two - will normally happen later, after other transfers complete, and - if the controller is idle it will need to be kickstarted. - master->cleanup(struct spi_device *spi) Your controller driver may use spi_device.controller_state to hold state it dynamically associates with that device. If you do that, be sure to provide the cleanup() method to free that state. + master->prepare_transfer_hardware(struct spi_master *master) + This will be called by the queue mechanism to signal to the driver + that a message is coming in soon, so the subsystem requests the + driver to prepare the transfer hardware by issuing this call. + This may sleep. + + master->unprepare_transfer_hardware(struct spi_master *master) + This will be called by the queue mechanism to signal to the driver + that there are no more messages pending in the queue and it may + relax the hardware (e.g. by power management calls). This may sleep. + + master->transfer_one_message(struct spi_master *master, + struct spi_message *mesg) + The subsystem calls the driver to transfer a single message while + queuing transfers that arrive in the meantime. When the driver is + finished with this message, it must call + spi_finalize_current_message() so the subsystem can issue the next + message. This may sleep. + + master->transfer_one(struct spi_master *master, struct spi_device *spi, + struct spi_transfer *transfer) + The subsystem calls the driver to transfer a single transfer while + queuing transfers that arrive in the meantime. When the driver is + finished with this transfer, it must call + spi_finalize_current_transfer() so the subsystem can issue the next + transfer. This may sleep. Note: transfer_one and transfer_one_message + are mutually exclusive; when both are set, the generic subsystem does + not call your transfer_one callback. + + Return values: + negative errno: error + 0: transfer is finished + 1: transfer is still in progress + + DEPRECATED METHODS + + master->transfer(struct spi_device *spi, struct spi_message *message) + This must not sleep. Its responsibility is to arrange that the + transfer happens and its complete() callback is issued. The two + will normally happen later, after other transfers complete, and + if the controller is idle it will need to be kickstarted. This + method is not used on queued controllers and must be NULL if + transfer_one_message() and (un)prepare_transfer_hardware() are + implemented. + SPI MESSAGE QUEUE -The bulk of the driver will be managing the I/O queue fed by transfer(). +If you are happy with the standard queueing mechanism provided by the +SPI subsystem, just implement the queued methods specified above. Using +the message queue has the upside of centralizing a lot of code and +providing pure process-context execution of methods. The message queue +can also be elevated to realtime priority on high-priority SPI traffic. + +Unless the queueing mechanism in the SPI subsystem is selected, the bulk +of the driver will be managing the I/O queue fed by the now deprecated +function transfer(). That queue could be purely conceptual. For example, a driver used only for low-frequency sensor access might be fine using synchronous PIO. @@ -561,4 +608,6 @@ Stephen Street Mark Underwood Andrew Victor Vitaly Wool - +Grant Likely +Mark Brown +Linus Walleij |