diff options
Diffstat (limited to 'Documentation/networking/phy.txt')
| -rw-r--r-- | Documentation/networking/phy.txt | 46 |
1 files changed, 20 insertions, 26 deletions
diff --git a/Documentation/networking/phy.txt b/Documentation/networking/phy.txt index 88bb71b46da..3544c98401f 100644 --- a/Documentation/networking/phy.txt +++ b/Documentation/networking/phy.txt @@ -48,7 +48,7 @@ The MDIO bus time, so it is safe for them to block, waiting for an interrupt to signal the operation is complete - 2) A reset function is necessary. This is used to return the bus to an + 2) A reset function is optional. This is used to return the bus to an initialized state. 3) A probe function is needed. This function should set up anything the bus @@ -62,7 +62,8 @@ The MDIO bus 5) The bus must also be declared somewhere as a device, and registered. As an example for how one driver implemented an mdio bus driver, see - drivers/net/gianfar_mii.c and arch/ppc/syslib/mpc85xx_devices.c + drivers/net/ethernet/freescale/fsl_pq_mdio.c and an associated DTS file + for one of the users. (e.g. "git grep fsl,.*-mdio arch/powerpc/boot/dts/") Connecting to a PHY @@ -102,7 +103,7 @@ Letting the PHY Abstraction Layer do Everything Now, to connect, just call this function: - phydev = phy_connect(dev, phy_name, &adjust_link, flags, interface); + phydev = phy_connect(dev, phy_name, &adjust_link, interface); phydev is a pointer to the phy_device structure which represents the PHY. If phy_connect is successful, it will return the pointer. dev, here, is the @@ -112,7 +113,9 @@ Letting the PHY Abstraction Layer do Everything current state, though the PHY will not yet be truly operational at this point. - flags is a u32 which can optionally contain phy-specific flags. + PHY-specific flags should be set in phydev->dev_flags prior to the call + to phy_connect() such that the underlying PHY driver can check for flags + and perform specific operations based on them. This is useful if the system has put hardware restrictions on the PHY/controller, of which the PHY needs to be aware. @@ -177,18 +180,6 @@ Doing it all yourself A convenience function to print out the PHY status neatly. - int phy_clear_interrupt(struct phy_device *phydev); - int phy_config_interrupt(struct phy_device *phydev, u32 interrupts); - - Clear the PHY's interrupt, and configure which ones are allowed, - respectively. Currently only supports all on, or all off. - - int phy_enable_interrupts(struct phy_device *phydev); - int phy_disable_interrupts(struct phy_device *phydev); - - Functions which enable/disable PHY interrupts, clearing them - before and after, respectively. - int phy_start_interrupts(struct phy_device *phydev); int phy_stop_interrupts(struct phy_device *phydev); @@ -196,11 +187,10 @@ Doing it all yourself start, or disables then frees them for stop. struct phy_device * phy_attach(struct net_device *dev, const char *phy_id, - u32 flags, phy_interface_t interface); + phy_interface_t interface); Attaches a network device to a particular PHY, binding the PHY to a generic - driver if none was found during bus initialization. Passes in - any phy-specific flags as needed. + driver if none was found during bus initialization. int phy_start_aneg(struct phy_device *phydev); @@ -213,12 +203,6 @@ Doing it all yourself Fills the phydev structure with up-to-date information about the current settings in the PHY. - void phy_sanitize_settings(struct phy_device *phydev) - - Resolves differences between currently desired settings, and - supported settings for the given PHY device. Does not make - the changes in the hardware, though. - int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd); @@ -269,15 +253,25 @@ Writing a PHY driver Each driver consists of a number of function pointers: + soft_reset: perform a PHY software reset config_init: configures PHY into a sane state after a reset. For instance, a Davicom PHY requires descrambling disabled. - probe: Does any setup needed by the driver + probe: Allocate phy->priv, optionally refuse to bind. + PHY may not have been reset or had fixups run yet. suspend/resume: power management config_aneg: Changes the speed/duplex/negotiation settings + aneg_done: Determines the auto-negotiation result read_status: Reads the current speed/duplex/negotiation settings ack_interrupt: Clear a pending interrupt + did_interrupt: Checks if the PHY generated an interrupt config_intr: Enable or disable interrupts remove: Does any driver take-down + ts_info: Queries about the HW timestamping status + hwtstamp: Set the PHY HW timestamping configuration + rxtstamp: Requests a receive timestamp at the PHY level for a 'skb' + txtsamp: Requests a transmit timestamp at the PHY level for a 'skb' + set_wol: Enable Wake-on-LAN at the PHY level + get_wol: Get the Wake-on-LAN status at the PHY level Of these, only config_aneg and read_status are required to be assigned by the driver code. The rest are optional. Also, it is |