diff options
Diffstat (limited to 'Documentation/hwmon')
129 files changed, 10105 insertions, 600 deletions
diff --git a/Documentation/hwmon/ab8500 b/Documentation/hwmon/ab8500 new file mode 100644 index 00000000000..cf169c8ef4e --- /dev/null +++ b/Documentation/hwmon/ab8500 @@ -0,0 +1,22 @@ +Kernel driver ab8500 +==================== + +Supported chips: + * ST-Ericsson AB8500 + Prefix: 'ab8500' + Addresses scanned: - + Datasheet: http://www.stericsson.com/developers/documentation.jsp + +Authors: + Martin Persson <martin.persson@stericsson.com> + Hongbo Zhang <hongbo.zhang@linaro.org> + +Description +----------- + +See also Documentation/hwmon/abx500. This is the ST-Ericsson AB8500 specific +driver. + +Currently only the AB8500 internal sensor and one external sensor for battery +temperature are monitored. Other GPADC channels can also be monitored if needed +in future. diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru new file mode 100644 index 00000000000..915f32063a2 --- /dev/null +++ b/Documentation/hwmon/abituguru @@ -0,0 +1,92 @@ +Kernel driver abituguru +======================= + +Supported chips: + * Abit uGuru revision 1 & 2 (Hardware Monitor part only) + Prefix: 'abituguru' + Addresses scanned: ISA 0x0E0 + Datasheet: Not available, this driver is based on reverse engineering. + A "Datasheet" has been written based on the reverse engineering it + should be available in the same dir as this file under the name + abituguru-datasheet. + Note: + The uGuru is a microcontroller with onboard firmware which programs + it to behave as a hwmon IC. There are many different revisions of the + firmware and thus effectivly many different revisions of the uGuru. + Below is an incomplete list with which revisions are used for which + Motherboards: + uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) (1) + uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO) + uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8) + uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty) + uGuru 2.3.0.0 ~ 2.3.0.9 (AN8) + uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X, + AW9D-MAX) (2) + 1) For revisions 2 and 3 uGuru's the driver can autodetect the + sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's + this doesnot always work. For these uGuru's the autodection can + be overriden with the bank1_types module param. For all 3 known + revison 1 motherboards the correct use of this param is: + bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1 + You may also need to specify the fan_sensors option for these boards + fan_sensors=5 + 2) There is a separate abituguru3 driver for these motherboards, + the abituguru (without the 3 !) driver will not work on these + motherboards (and visa versa)! + +Authors: + Hans de Goede <j.w.r.degoede@hhs.nl>, + (Initial reverse engineering done by Olle Sandberg + <ollebull@gmail.com>) + + +Module Parameters +----------------- + +* force: bool Force detection. Note this parameter only causes the + detection to be skipped, and thus the insmod to + succeed. If the uGuru can't be read the actual hwmon + driver will not load and thus no hwmon device will get + registered. +* bank1_types: int[] Bank1 sensortype autodetection override: + -1 autodetect (default) + 0 volt sensor + 1 temp sensor + 2 not connected +* fan_sensors: int Tell the driver how many fan speed sensors there are + on your motherboard. Default: 0 (autodetect). +* pwms: int Tell the driver how many fan speed controls (fan + pwms) your motherboard has. Default: 0 (autodetect). +* verbose: int How verbose should the driver be? (0-3): + 0 normal output + 1 + verbose error reporting + 2 + sensors type probing info (default) + 3 + retryable error reporting + Default: 2 (the driver is still in the testing phase) + +Notice if you need any of the first three options above please insmod the +driver with verbose set to 3 and mail me <j.w.r.degoede@hhs.nl> the output of: +dmesg | grep abituguru + + +Description +----------- + +This driver supports the hardware monitoring features of the first and +second revision of the Abit uGuru chip found on Abit uGuru featuring +motherboards (most modern Abit motherboards). + +The first and second revision of the uGuru chip in reality is a Winbond +W83L950D in disguise (despite Abit claiming it is "a new microprocessor +designed by the ABIT Engineers"). Unfortunately this doesn't help since the +W83L950D is a generic microcontroller with a custom Abit application running +on it. + +Despite Abit not releasing any information regarding the uGuru, Olle +Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part +of the uGuru. Without his work this driver would not have been possible. + +Known Issues +------------ + +The voltage and frequency control parts of the Abit uGuru are not supported. diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet new file mode 100644 index 00000000000..86c0b1251c8 --- /dev/null +++ b/Documentation/hwmon/abituguru-datasheet @@ -0,0 +1,312 @@ +uGuru datasheet +=============== + +First of all, what I know about uGuru is no fact based on any help, hints or +datasheet from Abit. The data I have got on uGuru have I assembled through +my weak knowledge in "backwards engineering". +And just for the record, you may have noticed uGuru isn't a chip developed by +Abit, as they claim it to be. It's really just an microprocessor (uC) created by +Winbond (W83L950D). And no, reading the manual for this specific uC or +mailing Windbond for help won't give any useful data about uGuru, as it is +the program inside the uC that is responding to calls. + +Olle Sandberg <ollebull@gmail.com>, 2005-05-25 + + +Original version by Olle Sandberg who did the heavy lifting of the initial +reverse engineering. This version has been almost fully rewritten for clarity +and extended with write support and info on more databanks, the write support +is once again reverse engineered by Olle the additional databanks have been +reverse engineered by me. I would like to express my thanks to Olle, this +document and the Linux driver could not have been written without his efforts. + +Note: because of the lack of specs only the sensors part of the uGuru is +described here and not the CPU / RAM / etc voltage & frequency control. + +Hans de Goede <j.w.r.degoede@hhs.nl>, 28-01-2006 + + +Detection +========= + +As far as known the uGuru is always placed at and using the (ISA) I/O-ports +0xE0 and 0xE4, so we don't have to scan any port-range, just check what the two +ports are holding for detection. We will refer to 0xE0 as CMD (command-port) +and 0xE4 as DATA because Abit refers to them with these names. + +If DATA holds 0x00 or 0x08 and CMD holds 0x00 or 0xAC an uGuru could be +present. We have to check for two different values at data-port, because +after a reboot uGuru will hold 0x00 here, but if the driver is removed and +later on attached again data-port will hold 0x08, more about this later. + +After wider testing of the Linux kernel driver some variants of the uGuru have +turned up which will hold 0x00 instead of 0xAC at the CMD port, thus we also +have to test CMD for two different values. On these uGuru's DATA will initially +hold 0x09 and will only hold 0x08 after reading CMD first, so CMD must be read +first! + +To be really sure an uGuru is present a test read of one or more register +sets should be done. + + +Reading / Writing +================= + +Addressing +---------- + +The uGuru has a number of different addressing levels. The first addressing +level we will call banks. A bank holds data for one or more sensors. The data +in a bank for a sensor is one or more bytes large. + +The number of bytes is fixed for a given bank, you should always read or write +that many bytes, reading / writing more will fail, the results when writing +less then the number of bytes for a given bank are undetermined. + +See below for all known bank addresses, numbers of sensors in that bank, +number of bytes data per sensor and contents/meaning of those bytes. + +Although both this document and the kernel driver have kept the sensor +terminoligy for the addressing within a bank this is not 100% correct, in +bank 0x24 for example the addressing within the bank selects a PWM output not +a sensor. + +Notice that some banks have both a read and a write address this is how the +uGuru determines if a read from or a write to the bank is taking place, thus +when reading you should always use the read address and when writing the +write address. The write address is always one (1) more than the read address. + + +uGuru ready +----------- + +Before you can read from or write to the uGuru you must first put the uGuru +in "ready" mode. + +To put the uGuru in ready mode first write 0x00 to DATA and then wait for DATA +to hold 0x09, DATA should read 0x09 within 250 read cycles. + +Next CMD _must_ be read and should hold 0xAC, usually CMD will hold 0xAC the +first read but sometimes it takes a while before CMD holds 0xAC and thus it +has to be read a number of times (max 50). + +After reading CMD, DATA should hold 0x08 which means that the uGuru is ready +for input. As above DATA will usually hold 0x08 the first read but not always. +This step can be skipped, but it is undetermined what happens if the uGuru has +not yet reported 0x08 at DATA and you proceed with writing a bank address. + + +Sending bank and sensor addresses to the uGuru +---------------------------------------------- + +First the uGuru must be in "ready" mode as described above, DATA should hold +0x08 indicating that the uGuru wants input, in this case the bank address. + +Next write the bank address to DATA. After the bank address has been written +wait for to DATA to hold 0x08 again indicating that it wants / is ready for +more input (max 250 reads). + +Once DATA holds 0x08 again write the sensor address to CMD. + + +Reading +------- + +First send the bank and sensor addresses as described above. +Then for each byte of data you want to read wait for DATA to hold 0x01 +which indicates that the uGuru is ready to be read (max 250 reads) and once +DATA holds 0x01 read the byte from CMD. + +Once all bytes have been read data will hold 0x09, but there is no reason to +test for this. Notice that the number of bytes is bank address dependent see +above and below. + +After completing a successful read it is advised to put the uGuru back in +ready mode, so that it is ready for the next read / write cycle. This way +if your program / driver is unloaded and later loaded again the detection +algorithm described above will still work. + + + +Writing +------- + +First send the bank and sensor addresses as described above. +Then for each byte of data you want to write wait for DATA to hold 0x00 +which indicates that the uGuru is ready to be written (max 250 reads) and +once DATA holds 0x00 write the byte to CMD. + +Once all bytes have been written wait for DATA to hold 0x01 (max 250 reads) +don't ask why this is the way it is. + +Once DATA holds 0x01 read CMD it should hold 0xAC now. + +After completing a successful write it is advised to put the uGuru back in +ready mode, so that it is ready for the next read / write cycle. This way +if your program / driver is unloaded and later loaded again the detection +algorithm described above will still work. + + +Gotchas +------- + +After wider testing of the Linux kernel driver some variants of the uGuru have +turned up which do not hold 0x08 at DATA within 250 reads after writing the +bank address. With these versions this happens quite frequent, using larger +timeouts doesn't help, they just go offline for a second or 2, doing some +internal callibration or whatever. Your code should be prepared to handle +this and in case of no response in this specific case just goto sleep for a +while and then retry. + + +Address Map +=========== + +Bank 0x20 Alarms (R) +-------------------- +This bank contains 0 sensors, iow the sensor address is ignored (but must be +written) just use 0. Bank 0x20 contains 3 bytes: + +Byte 0: +This byte holds the alarm flags for sensor 0-7 of Sensor Bank1, with bit 0 +corresponding to sensor 0, 1 to 1, etc. + +Byte 1: +This byte holds the alarm flags for sensor 8-15 of Sensor Bank1, with bit 0 +corresponding to sensor 8, 1 to 9, etc. + +Byte 2: +This byte holds the alarm flags for sensor 0-5 of Sensor Bank2, with bit 0 +corresponding to sensor 0, 1 to 1, etc. + + +Bank 0x21 Sensor Bank1 Values / Readings (R) +-------------------------------------------- +This bank contains 16 sensors, for each sensor it contains 1 byte. +So far the following sensors are known to be available on all motherboards: +Sensor 0 CPU temp +Sensor 1 SYS temp +Sensor 3 CPU core volt +Sensor 4 DDR volt +Sensor 10 DDR Vtt volt +Sensor 15 PWM temp + +Byte 0: +This byte holds the reading from the sensor. Sensors in Bank1 can be both +volt and temp sensors, this is motherboard specific. The uGuru however does +seem to know (be programmed with) what kindoff sensor is attached see Sensor +Bank1 Settings description. + +Volt sensors use a linear scale, a reading 0 corresponds with 0 volt and a +reading of 255 with 3494 mV. The sensors for higher voltages however are +connected through a division circuit. The currently known division circuits +in use result in ranges of: 0-4361mV, 0-6248mV or 0-14510mV. 3.3 volt sources +use the 0-4361mV range, 5 volt the 0-6248mV and 12 volt the 0-14510mV . + +Temp sensors also use a linear scale, a reading of 0 corresponds with 0 degree +Celsius and a reading of 255 with a reading of 255 degrees Celsius. + + +Bank 0x22 Sensor Bank1 Settings (R) +Bank 0x23 Sensor Bank1 Settings (W) +----------------------------------- + +This bank contains 16 sensors, for each sensor it contains 3 bytes. Each +set of 3 bytes contains the settings for the sensor with the same sensor +address in Bank 0x21 . + +Byte 0: +Alarm behaviour for the selected sensor. A 1 enables the described behaviour. +Bit 0: Give an alarm if measured temp is over the warning threshold (RW) * +Bit 1: Give an alarm if measured volt is over the max threshold (RW) ** +Bit 2: Give an alarm if measured volt is under the min threshold (RW) ** +Bit 3: Beep if alarm (RW) +Bit 4: 1 if alarm cause measured temp is over the warning threshold (R) +Bit 5: 1 if alarm cause measured volt is over the max threshold (R) +Bit 6: 1 if alarm cause measured volt is under the min threshold (R) +Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds (RW) + Temp sensor: Shutdown if temp is over the shutdown threshold (RW) + +* This bit is only honored/used by the uGuru if a temp sensor is connected +** This bit is only honored/used by the uGuru if a volt sensor is connected +Note with some trickery this can be used to find out what kinda sensor is +detected see the Linux kernel driver for an example with many comments on +how todo this. + +Byte 1: +Temp sensor: warning threshold (scale as bank 0x21) +Volt sensor: min threshold (scale as bank 0x21) + +Byte 2: +Temp sensor: shutdown threshold (scale as bank 0x21) +Volt sensor: max threshold (scale as bank 0x21) + + +Bank 0x24 PWM outputs for FAN's (R) +Bank 0x25 PWM outputs for FAN's (W) +----------------------------------- + +This bank contains 3 "sensors", for each sensor it contains 5 bytes. +Sensor 0 usually controls the CPU fan +Sensor 1 usually controls the NB (or chipset for single chip) fan +Sensor 2 usually controls the System fan + +Byte 0: +Flag 0x80 to enable control, Fan runs at 100% when disabled. +low nibble (temp)sensor address at bank 0x21 used for control. + +Byte 1: +0-255 = 0-12v (linear), specify voltage at which fan will rotate when under +low threshold temp (specified in byte 3) + +Byte 2: +0-255 = 0-12v (linear), specify voltage at which fan will rotate when above +high threshold temp (specified in byte 4) + +Byte 3: +Low threshold temp (scale as bank 0x21) + +byte 4: +High threshold temp (scale as bank 0x21) + + +Bank 0x26 Sensors Bank2 Values / Readings (R) +--------------------------------------------- + +This bank contains 6 sensors (AFAIK), for each sensor it contains 1 byte. +So far the following sensors are known to be available on all motherboards: +Sensor 0: CPU fan speed +Sensor 1: NB (or chipset for single chip) fan speed +Sensor 2: SYS fan speed + +Byte 0: +This byte holds the reading from the sensor. 0-255 = 0-15300 (linear) + + +Bank 0x27 Sensors Bank2 Settings (R) +Bank 0x28 Sensors Bank2 Settings (W) +------------------------------------ + +This bank contains 6 sensors (AFAIK), for each sensor it contains 2 bytes. + +Byte 0: +Alarm behaviour for the selected sensor. A 1 enables the described behaviour. +Bit 0: Give an alarm if measured rpm is under the min threshold (RW) +Bit 3: Beep if alarm (RW) +Bit 7: Shutdown if alarm persist for more than 4 seconds (RW) + +Byte 1: +min threshold (scale as bank 0x26) + + +Warning for the adventurous +=========================== + +A word of caution to those who want to experiment and see if they can figure +the voltage / clock programming out, I tried reading and only reading banks +0-0x30 with the reading code used for the sensor banks (0x20-0x28) and this +resulted in a _permanent_ reprogramming of the voltages, luckily I had the +sensors part configured so that it would shutdown my system on any out of spec +voltages which proprably safed my computer (after a reboot I managed to +immediately enter the bios and reload the defaults). This probably means that +the read/write cycle for the non sensor part is different from the sensor part. diff --git a/Documentation/hwmon/abituguru3 b/Documentation/hwmon/abituguru3 new file mode 100644 index 00000000000..a6ccfe4bb6a --- /dev/null +++ b/Documentation/hwmon/abituguru3 @@ -0,0 +1,65 @@ +Kernel driver abituguru3 +======================== + +Supported chips: + * Abit uGuru revision 3 (Hardware Monitor part, reading only) + Prefix: 'abituguru3' + Addresses scanned: ISA 0x0E0 + Datasheet: Not available, this driver is based on reverse engineering. + Note: + The uGuru is a microcontroller with onboard firmware which programs + it to behave as a hwmon IC. There are many different revisions of the + firmware and thus effectivly many different revisions of the uGuru. + Below is an incomplete list with which revisions are used for which + Motherboards: + uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) + uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO) + uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8) + uGuru 2.3.0.0 ~ 2.3.0.9 (AN8) + uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X, + AW9D-MAX) + The abituguru3 driver is only for revison 3.0.x.x motherboards, + this driver will not work on older motherboards. For older + motherboards use the abituguru (without the 3 !) driver. + +Authors: + Hans de Goede <j.w.r.degoede@hhs.nl>, + (Initial reverse engineering done by Louis Kruger) + + +Module Parameters +----------------- + +* force: bool Force detection. Note this parameter only causes the + detection to be skipped, and thus the insmod to + succeed. If the uGuru can't be read the actual hwmon + driver will not load and thus no hwmon device will get + registered. +* verbose: bool Should the driver be verbose? + 0/off/false normal output + 1/on/true + verbose error reporting (default) + Default: 1 (the driver is still in the testing phase) + +Description +----------- + +This driver supports the hardware monitoring features of the third revision of +the Abit uGuru chip, found on recent Abit uGuru featuring motherboards. + +The 3rd revision of the uGuru chip in reality is a Winbond W83L951G. +Unfortunately this doesn't help since the W83L951G is a generic microcontroller +with a custom Abit application running on it. + +Despite Abit not releasing any information regarding the uGuru revision 3, +Louis Kruger has managed to reverse engineer the sensor part of the uGuru. +Without his work this driver would not have been possible. + +Known Issues +------------ + +The voltage and frequency control parts of the Abit uGuru are not supported, +neither is writing any of the sensor settings and writing / reading the +fanspeed control registers (FanEQ) + +If you encounter any problems please mail me <j.w.r.degoede@hhs.nl> and +include the output of: "dmesg | grep abituguru" diff --git a/Documentation/hwmon/abx500 b/Documentation/hwmon/abx500 new file mode 100644 index 00000000000..319a058cec7 --- /dev/null +++ b/Documentation/hwmon/abx500 @@ -0,0 +1,28 @@ +Kernel driver abx500 +==================== + +Supported chips: + * ST-Ericsson ABx500 series + Prefix: 'abx500' + Addresses scanned: - + Datasheet: http://www.stericsson.com/developers/documentation.jsp + +Authors: + Martin Persson <martin.persson@stericsson.com> + Hongbo Zhang <hongbo.zhang@linaro.org> + +Description +----------- + +Every ST-Ericsson Ux500 SOC consists of both ABx500 and DBx500 physically, +this is kernel hwmon driver for ABx500. + +There are some GPADCs inside ABx500 which are designed for connecting to +thermal sensors, and there is also a thermal sensor inside ABx500 too, which +raises interrupt when critical temperature reached. + +This abx500 is a common layer which can monitor all of the sensors, every +specific abx500 chip has its special configurations in its own file, e.g. some +sensors can be configured invisible if they are not available on that chip, and +the corresponding gpadc_addr should be set to 0, thus this sensor won't be +polled. diff --git a/Documentation/hwmon/acpi_power_meter b/Documentation/hwmon/acpi_power_meter new file mode 100644 index 00000000000..c80399a00c5 --- /dev/null +++ b/Documentation/hwmon/acpi_power_meter @@ -0,0 +1,51 @@ +Kernel driver power_meter +========================= + +This driver talks to ACPI 4.0 power meters. + +Supported systems: + * Any recent system with ACPI 4.0. + Prefix: 'power_meter' + Datasheet: http://acpi.info/, section 10.4. + +Author: Darrick J. Wong + +Description +----------- + +This driver implements sensor reading support for the power meters exposed in +the ACPI 4.0 spec (Chapter 10.4). These devices have a simple set of +features--a power meter that returns average power use over a configurable +interval, an optional capping mechanism, and a couple of trip points. The +sysfs interface conforms with the specification outlined in the "Power" section +of Documentation/hwmon/sysfs-interface. + +Special Features +---------------- + +The power[1-*]_is_battery knob indicates if the power supply is a battery. +Both power[1-*]_average_{min,max} must be set before the trip points will work. +When both of them are set, an ACPI event will be broadcast on the ACPI netlink +socket and a poll notification will be sent to the appropriate +power[1-*]_average sysfs file. + +The power[1-*]_{model_number, serial_number, oem_info} fields display arbitrary +strings that ACPI provides with the meter. The measures/ directory contains +symlinks to the devices that this meter measures. + +Some computers have the ability to enforce a power cap in hardware. If this is +the case, the power[1-*]_cap and related sysfs files will appear. When the +average power consumption exceeds the cap, an ACPI event will be broadcast on +the netlink event socket and a poll notification will be sent to the +appropriate power[1-*]_alarm file to indicate that capping has begun, and the +hardware has taken action to reduce power consumption. Most likely this will +result in reduced performance. + +There are a few other ACPI notifications that can be sent by the firmware. In +all cases the ACPI event will be broadcast on the ACPI netlink event socket as +well as sent as a poll notification to a sysfs file. The events are as +follows: + +power[1-*]_cap will be notified if the firmware changes the power cap. +power[1-*]_interval will be notified if the firmware changes the averaging +interval. diff --git a/Documentation/hwmon/ad7314 b/Documentation/hwmon/ad7314 new file mode 100644 index 00000000000..1912549c746 --- /dev/null +++ b/Documentation/hwmon/ad7314 @@ -0,0 +1,25 @@ +Kernel driver ad7314 +==================== + +Supported chips: + * Analog Devices AD7314 + Prefix: 'ad7314' + Datasheet: Publicly available at Analog Devices website. + * Analog Devices ADT7301 + Prefix: 'adt7301' + Datasheet: Publicly available at Analog Devices website. + * Analog Devices ADT7302 + Prefix: 'adt7302' + Datasheet: Publicly available at Analog Devices website. + +Description +----------- + +Driver supports the above parts. The ad7314 has a 10 bit +sensor with 1lsb = 0.25 degrees centigrade. The adt7301 and +adt7302 have 14 bit sensors with 1lsb = 0.03125 degrees centigrade. + +Notes +----- + +Currently power down mode is not supported. diff --git a/Documentation/hwmon/adc128d818 b/Documentation/hwmon/adc128d818 new file mode 100644 index 00000000000..39c95004dab --- /dev/null +++ b/Documentation/hwmon/adc128d818 @@ -0,0 +1,47 @@ +Kernel driver adc128d818 +======================== + +Supported chips: + * Texas Instruments ADC818D818 + Prefix: 'adc818d818' + Addresses scanned: I2C 0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f + Datasheet: Publicly available at the TI website + http://www.ti.com/ + +Author: Guenter Roeck + +Description +----------- + +This driver implements support for the Texas Instruments ADC128D818. +It is described as 'ADC System Monitor with Temperature Sensor'. + +The ADC128D818 implements one temperature sensor and seven voltage sensors. + +Temperatures are measured in degrees Celsius. There is one set of limits. +When the HOT Temperature Limit is crossed, this will cause an alarm that will +be reasserted until the temperature drops below the HOT Hysteresis. +Measurements are guaranteed between -55 and +125 degrees. The temperature +measurement has a resolution of 0.5 degrees; the limits have a resolution +of 1 degree. + +Voltage sensors (also known as IN sensors) report their values in volts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. Note that minimum in this case always means 'closest to +zero'; this is important for negative voltage measurements. All voltage +inputs can measure voltages between 0 and 2.55 volts, with a resolution +of 0.625 mV. + +If an alarm triggers, it will remain triggered until the hardware register +is read at least once. This means that the cause for the alarm may +already have disappeared by the time the alarm is read. The driver +caches the alarm status for each sensor until it is at least reported +once, to ensure that alarms are reported to user space. + +The ADC128D818 only updates its values approximately once per second; +reading it more often will do no harm, but will return 'old' values. + +In addition to the scanned address list, the chip can also be configured for +addresses 0x35 to 0x37. Those addresses are not scanned. You have to instantiate +the driver explicitly if the chip is configured for any of those addresses in +your system. diff --git a/Documentation/hwmon/adm1021 b/Documentation/hwmon/adm1021 index 03d02bfb3df..02ad96cf9b2 100644 --- a/Documentation/hwmon/adm1021 +++ b/Documentation/hwmon/adm1021 @@ -14,10 +14,6 @@ Supported chips: Prefix: 'gl523sm' Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e Datasheet: - * Intel Xeon Processor - Prefix: - any other - may require 'force_adm1021' parameter - Addresses scanned: none - Datasheet: Publicly available at Intel website * Maxim MAX1617 Prefix: 'max1617' Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e @@ -91,21 +87,27 @@ will do no harm, but will return 'old' values. It is possible to make ADM1021-clones do faster measurements, but there is really no good reason for that. -Xeon support ------------- -Some Xeon processors have real max1617, adm1021, or compatible chips -within them, with two temperature sensors. +Netburst-based Xeon support +--------------------------- -Other Xeons have chips with only one sensor. +Some Xeon processors based on the Netburst (early Pentium 4, from 2001 to +2003) microarchitecture had real MAX1617, ADM1021, or compatible chips +within them, with two temperature sensors. Other Xeon processors of this +era (with 400 MHz FSB) had chips with only one temperature sensor. -If you have a Xeon, and the adm1021 module loads, and both temperatures -appear valid, then things are good. +If you have such an old Xeon, and you get two valid temperatures when +loading the adm1021 module, then things are good. -If the adm1021 module doesn't load, you should try this: - modprobe adm1021 force_adm1021=BUS,ADDRESS - ADDRESS can only be 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. +If nothing happens when loading the adm1021 module, and you are certain +that your specific Xeon processor model includes compatible sensors, you +will have to explicitly instantiate the sensor chips from user-space. See +method 4 in Documentation/i2c/instantiating-devices. Possible slave +addresses are 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. It is likely that +only temp2 will be correct and temp1 will have to be ignored. -If you have dual Xeons you may have appear to have two separate -adm1021-compatible chips, or two single-temperature sensors, at distinct -addresses. +Previous generations of the Xeon processor (based on Pentium II/III) +didn't have these sensors. Next generations of Xeon processors (533 MHz +FSB and faster) lost them, until the Core-based generation which +introduced integrated digital thermal sensors. These are supported by +the coretemp driver. diff --git a/Documentation/hwmon/adm1025 b/Documentation/hwmon/adm1025 index 39d2b781b5d..99f05049c68 100644 --- a/Documentation/hwmon/adm1025 +++ b/Documentation/hwmon/adm1025 @@ -18,7 +18,7 @@ The NE1619 presents some differences with the original ADM1025: Authors: Chen-Yuan Wu <gwu@esoft.com>, - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Description ----------- diff --git a/Documentation/hwmon/adm1026 b/Documentation/hwmon/adm1026 index 473c689d792..d8fabe0c23a 100644 --- a/Documentation/hwmon/adm1026 +++ b/Documentation/hwmon/adm1026 @@ -6,7 +6,7 @@ Supported chips: Prefix: 'adm1026' Addresses scanned: I2C 0x2c, 0x2d, 0x2e Datasheet: Publicly available at the Analog Devices website - http://www.analog.com/en/prod/0,,766_825_ADM1026,00.html + http://www.onsemi.com/PowerSolutions/product.do?id=ADM1026 Authors: Philip Pokorny <ppokorny@penguincomputing.com> for Penguin Computing @@ -80,7 +80,7 @@ temperature sensor inputs. Both the PWM output and the DAC output can be used to control fan speed. Usually only one of these two outputs will be used. Write the minimum PWM or DAC value to the appropriate control register. Then set the low temperature limit in the tmin values for each -temperature sensor. The range of control is fixed at 20 °C, and the +temperature sensor. The range of control is fixed at 20 °C, and the largest difference between current and tmin of the temperature sensors sets the control output. See the datasheet for several example circuits for controlling fan speed with the PWM and DAC outputs. The fan speed sensors diff --git a/Documentation/hwmon/adm1031 b/Documentation/hwmon/adm1031 index 130a38382b9..a143117c99c 100644 --- a/Documentation/hwmon/adm1031 +++ b/Documentation/hwmon/adm1031 @@ -6,17 +6,17 @@ Supported chips: Prefix: 'adm1030' Addresses scanned: I2C 0x2c to 0x2e Datasheet: Publicly available at the Analog Devices website - http://products.analog.com/products/info.asp?product=ADM1030 + http://www.analog.com/en/prod/0%2C2877%2CADM1030%2C00.html * Analog Devices ADM1031 Prefix: 'adm1031' Addresses scanned: I2C 0x2c to 0x2e Datasheet: Publicly available at the Analog Devices website - http://products.analog.com/products/info.asp?product=ADM1031 + http://www.analog.com/en/prod/0%2C2877%2CADM1031%2C00.html Authors: Alexandre d'Alton <alex@alexdalton.org> - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Description ----------- diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275 new file mode 100644 index 00000000000..15b4a20d506 --- /dev/null +++ b/Documentation/hwmon/adm1275 @@ -0,0 +1,92 @@ +Kernel driver adm1275 +===================== + +Supported chips: + * Analog Devices ADM1075 + Prefix: 'adm1075' + Addresses scanned: - + Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1075.pdf + * Analog Devices ADM1275 + Prefix: 'adm1275' + Addresses scanned: - + Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1275.pdf + * Analog Devices ADM1276 + Prefix: 'adm1276' + Addresses scanned: - + Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1276.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for Analog Devices ADM1075, ADM1275, +and ADM1276 Hot-Swap Controller and Digital Power Monitor. + +ADM1075, ADM1275, and ADM1276 are hot-swap controllers that allow a circuit +board to be removed from or inserted into a live backplane. They also feature +current and voltage readback via an integrated 12-bit analog-to-digital +converter (ADC), accessed using a PMBus interface. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + +The ADM1075, unlike many other PMBus devices, does not support internal voltage +or current scaling. Reported voltages, currents, and power are raw measurements, +and will typically have to be scaled. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. Please see +Documentation/hwmon/pmbus for details. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write, history reset +attributes are write-only, all other attributes are read-only. + +in1_label "vin1" or "vout1" depending on chip variant and + configuration. On ADM1075, vout1 reports the voltage on + the VAUX pin. +in1_input Measured voltage. +in1_min Minimum Voltage. +in1_max Maximum voltage. +in1_min_alarm Voltage low alarm. +in1_max_alarm Voltage high alarm. +in1_highest Historical maximum voltage. +in1_reset_history Write any value to reset history. + +curr1_label "iout1" +curr1_input Measured current. +curr1_max Maximum current. +curr1_max_alarm Current high alarm. +curr1_lcrit Critical minimum current. Depending on the chip + configuration, either curr1_lcrit or curr1_crit is + supported, but not both. +curr1_lcrit_alarm Critical current low alarm. +curr1_crit Critical maximum current. Depending on the chip + configuration, either curr1_lcrit or curr1_crit is + supported, but not both. +curr1_crit_alarm Critical current high alarm. +curr1_highest Historical maximum current. +curr1_reset_history Write any value to reset history. + +power1_label "pin1" +power1_input Input power. +power1_reset_history Write any value to reset history. + + Power attributes are supported on ADM1075 and ADM1276 + only. diff --git a/Documentation/hwmon/adm9240 b/Documentation/hwmon/adm9240 index 35f618f3289..9b174fc700c 100644 --- a/Documentation/hwmon/adm9240 +++ b/Documentation/hwmon/adm9240 @@ -24,8 +24,8 @@ Authors: Frodo Looijaard <frodol@dds.nl>, Philip Edelbrock <phil@netroedge.com>, Michiel Rook <michiel@grendelproject.nl>, - Grant Coady <gcoady@gmail.com> with guidance - from Jean Delvare <khali@linux-fr.org> + Grant Coady <gcoady.lk@gmail.com> with guidance + from Jean Delvare <jdelvare@suse.de> Interface --------- @@ -155,7 +155,7 @@ connected to a normally open switch. The ADM9240 provides an internal open drain on this line, and may output a 20 ms active low pulse to reset an external Chassis Intrusion latch. -Clear the CI latch by writing value 1 to the sysfs chassis_clear file. +Clear the CI latch by writing value 0 to the sysfs intrusion0_alarm file. Alarm flags reported as 16-bit word diff --git a/Documentation/hwmon/ads1015 b/Documentation/hwmon/ads1015 new file mode 100644 index 00000000000..063b80d857b --- /dev/null +++ b/Documentation/hwmon/ads1015 @@ -0,0 +1,76 @@ +Kernel driver ads1015 +===================== + +Supported chips: + * Texas Instruments ADS1015 + Prefix: 'ads1015' + Datasheet: Publicly available at the Texas Instruments website : + http://focus.ti.com/lit/ds/symlink/ads1015.pdf + * Texas Instruments ADS1115 + Prefix: 'ads1115' + Datasheet: Publicly available at the Texas Instruments website : + http://focus.ti.com/lit/ds/symlink/ads1115.pdf + +Authors: + Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de> + +Description +----------- + +This driver implements support for the Texas Instruments ADS1015/ADS1115. + +This device is a 12/16-bit A-D converter with 4 inputs. + +The inputs can be used single ended or in certain differential combinations. + +The inputs can be made available by 8 sysfs input files in0_input - in7_input: +in0: Voltage over AIN0 and AIN1. +in1: Voltage over AIN0 and AIN3. +in2: Voltage over AIN1 and AIN3. +in3: Voltage over AIN2 and AIN3. +in4: Voltage over AIN0 and GND. +in5: Voltage over AIN1 and GND. +in6: Voltage over AIN2 and GND. +in7: Voltage over AIN3 and GND. + +Which inputs are available can be configured using platform data or devicetree. + +By default all inputs are exported. + +Platform Data +------------- + +In linux/i2c/ads1015.h platform data is defined, channel_data contains +configuration data for the used input combinations: +- pga is the programmable gain amplifier (values are full scale) + 0: +/- 6.144 V + 1: +/- 4.096 V + 2: +/- 2.048 V + 3: +/- 1.024 V + 4: +/- 0.512 V + 5: +/- 0.256 V +- data_rate in samples per second + 0: 128 + 1: 250 + 2: 490 + 3: 920 + 4: 1600 + 5: 2400 + 6: 3300 + +Example: +struct ads1015_platform_data data = { + .channel_data = { + [2] = { .enabled = true, .pga = 1, .data_rate = 0 }, + [4] = { .enabled = true, .pga = 4, .data_rate = 5 }, + } +}; + +In this case only in2_input (FS +/- 4.096 V, 128 SPS) and in4_input +(FS +/- 0.512 V, 2400 SPS) would be created. + +Devicetree +---------- + +Configuration is also possible via devicetree: +Documentation/devicetree/bindings/hwmon/ads1015.txt diff --git a/Documentation/hwmon/ads7828 b/Documentation/hwmon/ads7828 new file mode 100644 index 00000000000..f6e263e0f60 --- /dev/null +++ b/Documentation/hwmon/ads7828 @@ -0,0 +1,58 @@ +Kernel driver ads7828 +===================== + +Supported chips: + * Texas Instruments/Burr-Brown ADS7828 + Prefix: 'ads7828' + Datasheet: Publicly available at the Texas Instruments website: + http://focus.ti.com/lit/ds/symlink/ads7828.pdf + + * Texas Instruments ADS7830 + Prefix: 'ads7830' + Datasheet: Publicly available at the Texas Instruments website: + http://focus.ti.com/lit/ds/symlink/ads7830.pdf + +Authors: + Steve Hardy <shardy@redhat.com> + Vivien Didelot <vivien.didelot@savoirfairelinux.com> + Guillaume Roguez <guillaume.roguez@savoirfairelinux.com> + +Platform data +------------- + +The ads7828 driver accepts an optional ads7828_platform_data structure (defined +in include/linux/platform_data/ads7828.h). The structure fields are: + +* diff_input: (bool) Differential operation + set to true for differential mode, false for default single ended mode. + +* ext_vref: (bool) External reference + set to true if it operates with an external reference, false for default + internal reference. + +* vref_mv: (unsigned int) Voltage reference + if using an external reference, set this to the reference voltage in mV, + otherwise it will default to the internal value (2500mV). This value will be + bounded with limits accepted by the chip, described in the datasheet. + + If no structure is provided, the configuration defaults to single ended + operation and internal voltage reference (2.5V). + +Description +----------- + +This driver implements support for the Texas Instruments ADS7828 and ADS7830. + +The ADS7828 device is a 12-bit 8-channel A/D converter, while the ADS7830 does +8-bit sampling. + +It can operate in single ended mode (8 +ve inputs) or in differential mode, +where 4 differential pairs can be measured. + +The chip also has the facility to use an external voltage reference. This +may be required if your hardware supplies the ADS7828 from a 5V supply, see +the datasheet for more details. + +There is no reliable way to identify this chip, so the driver will not scan +some addresses to try to auto-detect it. That means that you will have to +statically declare the device in the platform support code. diff --git a/Documentation/hwmon/adt7410 b/Documentation/hwmon/adt7410 new file mode 100644 index 00000000000..9817941e5f1 --- /dev/null +++ b/Documentation/hwmon/adt7410 @@ -0,0 +1,73 @@ +Kernel driver adt7410 +===================== + +Supported chips: + * Analog Devices ADT7410 + Prefix: 'adt7410' + Addresses scanned: None + Datasheet: Publicly available at the Analog Devices website + http://www.analog.com/static/imported-files/data_sheets/ADT7410.pdf + * Analog Devices ADT7420 + Prefix: 'adt7420' + Addresses scanned: None + Datasheet: Publicly available at the Analog Devices website + http://www.analog.com/static/imported-files/data_sheets/ADT7420.pdf + * Analog Devices ADT7310 + Prefix: 'adt7310' + Addresses scanned: None + Datasheet: Publicly available at the Analog Devices website + http://www.analog.com/static/imported-files/data_sheets/ADT7310.pdf + * Analog Devices ADT7320 + Prefix: 'adt7320' + Addresses scanned: None + Datasheet: Publicly available at the Analog Devices website + http://www.analog.com/static/imported-files/data_sheets/ADT7320.pdf + +Author: Hartmut Knaack <knaack.h@gmx.de> + +Description +----------- + +The ADT7310/ADT7410 is a temperature sensor with rated temperature range of +-55°C to +150°C. It has a high accuracy of +/-0.5°C and can be operated at a +resolution of 13 bits (0.0625°C) or 16 bits (0.0078°C). The sensor provides an +INT pin to indicate that a minimum or maximum temperature set point has been +exceeded, as well as a critical temperature (CT) pin to indicate that the +critical temperature set point has been exceeded. Both pins can be set up with a +common hysteresis of 0°C - 15°C and a fault queue, ranging from 1 to 4 events. +Both pins can individually set to be active-low or active-high, while the whole +device can either run in comparator mode or interrupt mode. The ADT7410 supports +continuous temperature sampling, as well as sampling one temperature value per +second or even just get one sample on demand for power saving. Besides, it can +completely power down its ADC, if power management is required. + +The ADT7320/ADT7420 is register compatible, the only differences being the +package, a slightly narrower operating temperature range (-40°C to +150°C), and +a better accuracy (0.25°C instead of 0.50°C.) + +The difference between the ADT7310/ADT7320 and ADT7410/ADT7420 is the control +interface, the ADT7310 and ADT7320 use SPI while the ADT7410 and ADT7420 use +I2C. + +Configuration Notes +------------------- + +Since the device uses one hysteresis value, which is an offset to minimum, +maximum and critical temperature, it can only be set for temp#_max_hyst. +However, temp#_min_hyst and temp#_crit_hyst show their corresponding +hysteresis. +The device is set to 16 bit resolution and comparator mode. + +sysfs-Interface +--------------- + +temp#_input - temperature input +temp#_min - temperature minimum setpoint +temp#_max - temperature maximum setpoint +temp#_crit - critical temperature setpoint +temp#_min_hyst - hysteresis for temperature minimum (read-only) +temp#_max_hyst - hysteresis for temperature maximum (read/write) +temp#_crit_hyst - hysteresis for critical temperature (read-only) +temp#_min_alarm - temperature minimum alarm flag +temp#_max_alarm - temperature maximum alarm flag +temp#_crit_alarm - critical temperature alarm flag diff --git a/Documentation/hwmon/adt7411 b/Documentation/hwmon/adt7411 new file mode 100644 index 00000000000..1632960f974 --- /dev/null +++ b/Documentation/hwmon/adt7411 @@ -0,0 +1,42 @@ +Kernel driver adt7411 +===================== + +Supported chips: + * Analog Devices ADT7411 + Prefix: 'adt7411' + Addresses scanned: 0x48, 0x4a, 0x4b + Datasheet: Publicly available at the Analog Devices website + +Author: Wolfram Sang (based on adt7470 by Darrick J. Wong) + +Description +----------- + +This driver implements support for the Analog Devices ADT7411 chip. There may +be other chips that implement this interface. + +The ADT7411 can use an I2C/SMBus compatible 2-wire interface or an +SPI-compatible 4-wire interface. It provides a 10-bit analog to digital +converter which measures 1 temperature, vdd and 8 input voltages. It has an +internal temperature sensor, but an external one can also be connected (one +loses 2 inputs then). There are high- and low-limit registers for all inputs. + +Check the datasheet for details. + +sysfs-Interface +--------------- + +in0_input - vdd voltage input +in[1-8]_input - analog 1-8 input +temp1_input - temperature input + +Besides standard interfaces, this driver adds (0 = off, 1 = on): + + adc_ref_vdd - Use vdd as reference instead of 2.25 V + fast_sampling - Sample at 22.5 kHz instead of 1.4 kHz, but drop filters + no_average - Turn off averaging over 16 samples + +Notes +----- + +SPI, external temperature sensor and limit registers are not supported yet. diff --git a/Documentation/hwmon/adt7462 b/Documentation/hwmon/adt7462 new file mode 100644 index 00000000000..ec660b32827 --- /dev/null +++ b/Documentation/hwmon/adt7462 @@ -0,0 +1,67 @@ +Kernel driver adt7462 +====================== + +Supported chips: + * Analog Devices ADT7462 + Prefix: 'adt7462' + Addresses scanned: I2C 0x58, 0x5C + Datasheet: Publicly available at the Analog Devices website + +Author: Darrick J. Wong + +Description +----------- + +This driver implements support for the Analog Devices ADT7462 chip family. + +This chip is a bit of a beast. It has 8 counters for measuring fan speed. It +can also measure 13 voltages or 4 temperatures, or various combinations of the +two. See the chip documentation for more details about the exact set of +configurations. This driver does not allow one to configure the chip; that is +left to the system designer. + +A sophisticated control system for the PWM outputs is designed into the ADT7462 +that allows fan speed to be adjusted automatically based on any of the three +temperature sensors. Each PWM output is individually adjustable and +programmable. Once configured, the ADT7462 will adjust the PWM outputs in +response to the measured temperatures without further host intervention. This +feature can also be disabled for manual control of the PWM's. + +Each of the measured inputs (voltage, temperature, fan speed) has +corresponding high/low limit values. The ADT7462 will signal an ALARM if +any measured value exceeds either limit. + +The ADT7462 samples all inputs continuously. The driver will not read +the registers more often than once every other second. Further, +configuration data is only read once per minute. + +Special Features +---------------- + +The ADT7462 have a 10-bit ADC and can therefore measure temperatures +with 0.25 degC resolution. + +The Analog Devices datasheet is very detailed and describes a procedure for +determining an optimal configuration for the automatic PWM control. + +The driver will report sensor labels when it is able to determine that +information from the configuration registers. + +Configuration Notes +------------------- + +Besides standard interfaces driver adds the following: + +* PWM Control + +* pwm#_auto_point1_pwm and temp#_auto_point1_temp and +* pwm#_auto_point2_pwm and temp#_auto_point2_temp - + +point1: Set the pwm speed at a lower temperature bound. +point2: Set the pwm speed at a higher temperature bound. + +The ADT7462 will scale the pwm between the lower and higher pwm speed when +the temperature is between the two temperature boundaries. PWM values range +from 0 (off) to 255 (full speed). Fan speed will be set to maximum when the +temperature sensor associated with the PWM control exceeds temp#_max. + diff --git a/Documentation/hwmon/adt7470 b/Documentation/hwmon/adt7470 new file mode 100644 index 00000000000..8ce4aa0a0f5 --- /dev/null +++ b/Documentation/hwmon/adt7470 @@ -0,0 +1,73 @@ +Kernel driver adt7470 +===================== + +Supported chips: + * Analog Devices ADT7470 + Prefix: 'adt7470' + Addresses scanned: I2C 0x2C, 0x2E, 0x2F + Datasheet: Publicly available at the Analog Devices website + +Author: Darrick J. Wong + +Description +----------- + +This driver implements support for the Analog Devices ADT7470 chip. There may +be other chips that implement this interface. + +The ADT7470 uses the 2-wire interface compatible with the SMBus 2.0 +specification. Using an analog to digital converter it measures up to ten (10) +external temperatures. It has four (4) 16-bit counters for measuring fan speed. +There are four (4) PWM outputs that can be used to control fan speed. + +A sophisticated control system for the PWM outputs is designed into the ADT7470 +that allows fan speed to be adjusted automatically based on any of the ten +temperature sensors. Each PWM output is individually adjustable and +programmable. Once configured, the ADT7470 will adjust the PWM outputs in +response to the measured temperatures with further host intervention. This +feature can also be disabled for manual control of the PWM's. + +Each of the measured inputs (temperature, fan speed) has corresponding high/low +limit values. The ADT7470 will signal an ALARM if any measured value exceeds +either limit. + +The ADT7470 samples all inputs continuously. A kernel thread is started up for +the purpose of periodically querying the temperature sensors, thus allowing the +automatic fan pwm control to set the fan speed. The driver will not read the +registers more often than once every 5 seconds. Further, configuration data is +only read once per minute. + +Special Features +---------------- + +The ADT7470 has a 8-bit ADC and is capable of measuring temperatures with 1 +degC resolution. + +The Analog Devices datasheet is very detailed and describes a procedure for +determining an optimal configuration for the automatic PWM control. + +Configuration Notes +------------------- + +Besides standard interfaces driver adds the following: + +* PWM Control + +* pwm#_auto_point1_pwm and pwm#_auto_point1_temp and +* pwm#_auto_point2_pwm and pwm#_auto_point2_temp - + +point1: Set the pwm speed at a lower temperature bound. +point2: Set the pwm speed at a higher temperature bound. + +The ADT7470 will scale the pwm between the lower and higher pwm speed when +the temperature is between the two temperature boundaries. PWM values range +from 0 (off) to 255 (full speed). Fan speed will be set to maximum when the +temperature sensor associated with the PWM control exceeds +pwm#_auto_point2_temp. + +Notes +----- + +The temperature inputs no longer need to be read periodically from userspace in +order for the automatic pwm algorithm to run. This was the case for earlier +versions of the driver. diff --git a/Documentation/hwmon/adt7475 b/Documentation/hwmon/adt7475 new file mode 100644 index 00000000000..0502f2b464e --- /dev/null +++ b/Documentation/hwmon/adt7475 @@ -0,0 +1,117 @@ +Kernel driver adt7475 +===================== + +Supported chips: + * Analog Devices ADT7473 + Prefix: 'adt7473' + Addresses scanned: I2C 0x2C, 0x2D, 0x2E + Datasheet: Publicly available at the On Semiconductors website + * Analog Devices ADT7475 + Prefix: 'adt7475' + Addresses scanned: I2C 0x2E + Datasheet: Publicly available at the On Semiconductors website + * Analog Devices ADT7476 + Prefix: 'adt7476' + Addresses scanned: I2C 0x2C, 0x2D, 0x2E + Datasheet: Publicly available at the On Semiconductors website + * Analog Devices ADT7490 + Prefix: 'adt7490' + Addresses scanned: I2C 0x2C, 0x2D, 0x2E + Datasheet: Publicly available at the On Semiconductors website + +Authors: + Jordan Crouse + Hans de Goede + Darrick J. Wong (documentation) + Jean Delvare + + +Description +----------- + +This driver implements support for the Analog Devices ADT7473, ADT7475, +ADT7476 and ADT7490 chip family. The ADT7473 and ADT7475 differ only in +minor details. The ADT7476 has additional features, including extra voltage +measurement inputs and VID support. The ADT7490 also has additional +features, including extra voltage measurement inputs and PECI support. All +the supported chips will be collectively designed by the name "ADT747x" in +the rest of this document. + +The ADT747x uses the 2-wire interface compatible with the SMBus 2.0 +specification. Using an analog to digital converter it measures three (3) +temperatures and two (2) or more voltages. It has four (4) 16-bit counters +for measuring fan speed. There are three (3) PWM outputs that can be used +to control fan speed. + +A sophisticated control system for the PWM outputs is designed into the +ADT747x that allows fan speed to be adjusted automatically based on any of the +three temperature sensors. Each PWM output is individually adjustable and +programmable. Once configured, the ADT747x will adjust the PWM outputs in +response to the measured temperatures without further host intervention. +This feature can also be disabled for manual control of the PWM's. + +Each of the measured inputs (voltage, temperature, fan speed) has +corresponding high/low limit values. The ADT747x will signal an ALARM if +any measured value exceeds either limit. + +The ADT747x samples all inputs continuously. The driver will not read +the registers more often than once every other second. Further, +configuration data is only read once per minute. + +Chip Differences Summary +------------------------ + +ADT7473: + * 2 voltage inputs + * system acoustics optimizations (not implemented) + +ADT7475: + * 2 voltage inputs + +ADT7476: + * 5 voltage inputs + * VID support + +ADT7490: + * 6 voltage inputs + * 1 Imon input (not implemented) + * PECI support (not implemented) + * 2 GPIO pins (not implemented) + * system acoustics optimizations (not implemented) + +Special Features +---------------- + +The ADT747x has a 10-bit ADC and can therefore measure temperatures +with a resolution of 0.25 degree Celsius. Temperature readings can be +configured either for two's complement format or "Offset 64" format, +wherein 64 is subtracted from the raw value to get the temperature value. + +The datasheet is very detailed and describes a procedure for determining +an optimal configuration for the automatic PWM control. + +Fan Speed Control +----------------- + +The driver exposes two trip points per PWM channel. + +point1: Set the PWM speed at the lower temperature bound +point2: Set the PWM speed at the higher temperature bound + +The ADT747x will scale the PWM linearly between the lower and higher PWM +speed when the temperature is between the two temperature boundaries. +Temperature boundaries are associated to temperature channels rather than +PWM outputs, and a given PWM output can be controlled by several temperature +channels. As a result, the ADT747x may compute more than one PWM value +for a channel at a given time, in which case the maximum value (fastest +fan speed) is applied. PWM values range from 0 (off) to 255 (full speed). + +Fan speed may be set to maximum when the temperature sensor associated with +the PWM control exceeds temp#_max. + +Notes +----- + +The nVidia binary driver presents an ADT7473 chip via an on-card i2c bus. +Unfortunately, they fail to set the i2c adapter class, so this driver may +fail to find the chip until the nvidia driver is patched. diff --git a/Documentation/hwmon/amc6821 b/Documentation/hwmon/amc6821 new file mode 100644 index 00000000000..ced8359c50f --- /dev/null +++ b/Documentation/hwmon/amc6821 @@ -0,0 +1,102 @@ +Kernel driver amc6821 +===================== + +Supported chips: + Texas Instruments AMC6821 + Prefix: 'amc6821' + Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e + Datasheet: http://focus.ti.com/docs/prod/folders/print/amc6821.html + +Authors: + Tomaz Mertelj <tomaz.mertelj@guest.arnes.si> + + +Description +----------- + +This driver implements support for the Texas Instruments amc6821 chip. +The chip has one on-chip and one remote temperature sensor and one pwm fan +regulator. +The pwm can be controlled either from software or automatically. + +The driver provides the following sensor accesses in sysfs: + +temp1_input ro on-chip temperature +temp1_min rw " +temp1_max rw " +temp1_crit rw " +temp1_min_alarm ro " +temp1_max_alarm ro " +temp1_crit_alarm ro " + +temp2_input ro remote temperature +temp2_min rw " +temp2_max rw " +temp2_crit rw " +temp2_min_alarm ro " +temp2_max_alarm ro " +temp2_crit_alarm ro " +temp2_fault ro " + +fan1_input ro tachometer speed +fan1_min rw " +fan1_max rw " +fan1_fault ro " +fan1_div rw Fan divisor can be either 2 or 4. + +pwm1 rw pwm1 +pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled + by remote temperature, 3=fan controlled by + combination of the on-chip temperature and + remote-sensor temperature, +pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3 +pwm1_auto_point1_pwm ro Hardwired to 0, shared for both + temperature channels. +pwm1_auto_point2_pwm rw This value is shared for both temperature + channels. +pwm1_auto_point3_pwm rw Hardwired to 255, shared for both + temperature channels. + +temp1_auto_point1_temp ro Hardwired to temp2_auto_point1_temp + which is rw. Below this temperature fan stops. +temp1_auto_point2_temp rw The low-temperature limit of the proportional + range. Below this temperature + pwm1 = pwm1_auto_point2_pwm. It can go from + 0 degree C to 124 degree C in steps of + 4 degree C. Read it out after writing to get + the actual value. +temp1_auto_point3_temp rw Above this temperature fan runs at maximum + speed. It can go from temp1_auto_point2_temp. + It can only have certain discrete values + which depend on temp1_auto_point2_temp and + pwm1_auto_point2_pwm. Read it out after + writing to get the actual value. + +temp2_auto_point1_temp rw Must be between 0 degree C and 63 degree C and + it defines the passive cooling temperature. + Below this temperature the fan stops in + the closed loop mode. +temp2_auto_point2_temp rw The low-temperature limit of the proportional + range. Below this temperature + pwm1 = pwm1_auto_point2_pwm. It can go from + 0 degree C to 124 degree C in steps + of 4 degree C. + +temp2_auto_point3_temp rw Above this temperature fan runs at maximum + speed. It can only have certain discrete + values which depend on temp2_auto_point2_temp + and pwm1_auto_point2_pwm. Read it out after + writing to get actual value. + + +Module parameters +----------------- + +If your board has a BIOS that initializes the amc6821 correctly, you should +load the module with: init=0. + +If your board BIOS doesn't initialize the chip, or you want +different settings, you can set the following parameters: +init=1, +pwminv: 0 default pwm output, 1 inverts pwm output. + diff --git a/Documentation/hwmon/asc7621 b/Documentation/hwmon/asc7621 new file mode 100644 index 00000000000..7287be7e1f2 --- /dev/null +++ b/Documentation/hwmon/asc7621 @@ -0,0 +1,296 @@ +Kernel driver asc7621 +================== + +Supported chips: + Andigilog aSC7621 and aSC7621a + Prefix: 'asc7621' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: http://www.fairview5.com/linux/asc7621/asc7621.pdf + +Author: + George Joseph + +Description provided by Dave Pivin @ Andigilog: + +Andigilog has both the PECI and pre-PECI versions of the Heceta-6, as +Intel calls them. Heceta-6e has high frequency PWM and Heceta-6p has +added PECI and a 4th thermal zone. The Andigilog aSC7611 is the +Heceta-6e part and aSC7621 is the Heceta-6p part. They are both in +volume production, shipping to Intel and their subs. + +We have enhanced both parts relative to the governing Intel +specification. First enhancement is temperature reading resolution. We +have used registers below 20h for vendor-specific functions in addition +to those in the Intel-specified vendor range. + +Our conversion process produces a result that is reported as two bytes. +The fan speed control uses this finer value to produce a "step-less" fan +PWM output. These two bytes are "read-locked" to guarantee that once a +high or low byte is read, the other byte is locked-in until after the +next read of any register. So to get an atomic reading, read high or low +byte, then the very next read should be the opposite byte. Our data +sheet says 10-bits of resolution, although you may find the lower bits +are active, they are not necessarily reliable or useful externally. We +chose not to mask them. + +We employ significant filtering that is user tunable as described in the +data sheet. Our temperature reports and fan PWM outputs are very smooth +when compared to the competition, in addition to the higher resolution +temperature reports. The smoother PWM output does not require user +intervention. + +We offer GPIO features on the former VID pins. These are open-drain +outputs or inputs and may be used as general purpose I/O or as alarm +outputs that are based on temperature limits. These are in 19h and 1Ah. + +We offer flexible mapping of temperature readings to thermal zones. Any +temperature may be mapped to any zone, which has a default assignment +that follows Intel's specs. + +Since there is a fan to zone assignment that allows for the "hotter" of +a set of zones to control the PWM of an individual fan, but there is no +indication to the user, we have added an indicator that shows which zone +is currently controlling the PWM for a given fan. This is in register +00h. + +Both remote diode temperature readings may be given an offset value such +that the reported reading as well as the temperature used to determine +PWM may be offset for system calibration purposes. + +PECI Extended configuration allows for having more than two domains per +PECI address and also provides an enabling function for each PECI +address. One could use our flexible zone assignment to have a zone +assigned to up to 4 PECI addresses. This is not possible in the default +Intel configuration. This would be useful in multi-CPU systems with +individual fans on each that would benefit from individual fan control. +This is in register 0Eh. + +The tachometer measurement system is flexible and able to adapt to many +fan types. We can also support pulse-stretched PWM so that 3-wire fans +may be used. These characteristics are in registers 04h to 07h. + +Finally, we have added a tach disable function that turns off the tach +measurement system for individual tachs in order to save power. That is +in register 75h. + +-- +aSC7621 Product Description + +The aSC7621 has a two wire digital interface compatible with SMBus 2.0. +Using a 10-bit ADC, the aSC7621 measures the temperature of two remote diode +connected transistors as well as its own die. Support for Platform +Environmental Control Interface (PECI) is included. + +Using temperature information from these four zones, an automatic fan speed +control algorithm is employed to minimize acoustic impact while achieving +recommended CPU temperature under varying operational loads. + +To set fan speed, the aSC7621 has three independent pulse width modulation +(PWM) outputs that are controlled by one, or a combination of three, +temperature zones. Both high- and low-frequency PWM ranges are supported. + +The aSC7621 also includes a digital filter that can be invoked to smooth +temperature readings for better control of fan speed and minimum acoustic +impact. + +The aSC7621 has tachometer inputs to measure fan speed on up to four fans. +Limit and status registers for all measured values are included to alert +the system host that any measurements are outside of programmed limits +via status registers. + +System voltages of VCCP, 2.5V, 3.3V, 5.0V, and 12V motherboard power are +monitored efficiently with internal scaling resistors. + +Features +- Supports PECI interface and monitors internal and remote thermal diodes +- 2-wire, SMBus 2.0 compliant, serial interface +- 10-bit ADC +- Monitors VCCP, 2.5V, 3.3V, 5.0V, and 12V motherboard/processor supplies +- Programmable autonomous fan control based on temperature readings +- Noise filtering of temperature reading for fan speed control +- 0.25C digital temperature sensor resolution +- 3 PWM fan speed control outputs for 2-, 3- or 4-wire fans and up to 4 fan + tachometer inputs +- Enhanced measured temperature to Temperature Zone assignment. +- Provides high and low PWM frequency ranges +- 3 GPIO pins for custom use +- 24-Lead QSOP package + +Configuration Notes +=================== + +Except where noted below, the sysfs entries created by this driver follow +the standards defined in "sysfs-interface". + +temp1_source + 0 (default) peci_legacy = 0, Remote 1 Temperature + peci_legacy = 1, PECI Processor Temperature 0 + 1 Remote 1 Temperature + 2 Remote 2 Temperature + 3 Internal Temperature + 4 PECI Processor Temperature 0 + 5 PECI Processor Temperature 1 + 6 PECI Processor Temperature 2 + 7 PECI Processor Temperature 3 + +temp2_source + 0 (default) Internal Temperature + 1 Remote 1 Temperature + 2 Remote 2 Temperature + 3 Internal Temperature + 4 PECI Processor Temperature 0 + 5 PECI Processor Temperature 1 + 6 PECI Processor Temperature 2 + 7 PECI Processor Temperature 3 + +temp3_source + 0 (default) Remote 2 Temperature + 1 Remote 1 Temperature + 2 Remote 2 Temperature + 3 Internal Temperature + 4 PECI Processor Temperature 0 + 5 PECI Processor Temperature 1 + 6 PECI Processor Temperature 2 + 7 PECI Processor Temperature 3 + +temp4_source + 0 (default) peci_legacy = 0, PECI Processor Temperature 0 + peci_legacy = 1, Remote 1 Temperature + 1 Remote 1 Temperature + 2 Remote 2 Temperature + 3 Internal Temperature + 4 PECI Processor Temperature 0 + 5 PECI Processor Temperature 1 + 6 PECI Processor Temperature 2 + 7 PECI Processor Temperature 3 + +temp[1-4]_smoothing_enable +temp[1-4]_smoothing_time + Smooths spikes in temp readings caused by noise. + Valid values in milliseconds are: + 35000 + 17600 + 11800 + 7000 + 4400 + 3000 + 1600 + 800 + +temp[1-4]_crit + When the corresponding zone temperature reaches this value, + ALL pwm outputs will got to 100%. + +temp[5-8]_input +temp[5-8]_enable + The aSC7621 can also read temperatures provided by the processor + via the PECI bus. Usually these are "core" temps and are relative + to the point where the automatic thermal control circuit starts + throttling. This means that these are usually negative numbers. + +pwm[1-3]_enable + 0 Fan off. + 1 Fan on manual control. + 2 Fan on automatic control and will run at the minimum pwm + if the temperature for the zone is below the minimum. + 3 Fan on automatic control but will be off if the temperature + for the zone is below the minimum. + 4-254 Ignored. + 255 Fan on full. + +pwm[1-3]_auto_channels + Bitmap as described in sysctl-interface with the following + exceptions... + Only the following combination of zones (and their corresponding masks) + are valid: + 1 + 2 + 3 + 2,3 + 1,2,3 + 4 + 1,2,3,4 + + Special values: + 0 Disabled. + 16 Fan on manual control. + 31 Fan on full. + + +pwm[1-3]_invert + When set, inverts the meaning of pwm[1-3]. + i.e. when pwm = 0, the fan will be on full and + when pwm = 255 the fan will be off. + +pwm[1-3]_freq + PWM frequency in Hz + Valid values in Hz are: + + 10 + 15 + 23 + 30 (default) + 38 + 47 + 62 + 94 + 23000 + 24000 + 25000 + 26000 + 27000 + 28000 + 29000 + 30000 + + Setting any other value will be ignored. + +peci_enable + Enables or disables PECI + +peci_avg + Input filter average time. + + 0 0 Sec. (no Smoothing) (default) + 1 0.25 Sec. + 2 0.5 Sec. + 3 1.0 Sec. + 4 2.0 Sec. + 5 4.0 Sec. + 6 8.0 Sec. + 7 0.0 Sec. + +peci_legacy + + 0 Standard Mode (default) + Remote Diode 1 reading is associated with + Temperature Zone 1, PECI is associated with + Zone 4 + + 1 Legacy Mode + PECI is associated with Temperature Zone 1, + Remote Diode 1 is associated with Zone 4 + +peci_diode + Diode filter + + 0 0.25 Sec. + 1 1.1 Sec. + 2 2.4 Sec. (default) + 3 3.4 Sec. + 4 5.0 Sec. + 5 6.8 Sec. + 6 10.2 Sec. + 7 16.4 Sec. + +peci_4domain + Four domain enable + + 0 1 or 2 Domains for enabled processors (default) + 1 3 or 4 Domains for enabled processors + +peci_domain + Domain + + 0 Processor contains a single domain (0) (default) + 1 Processor contains two domains (0,1) diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp new file mode 100644 index 00000000000..fec5a9bf755 --- /dev/null +++ b/Documentation/hwmon/coretemp @@ -0,0 +1,181 @@ +Kernel driver coretemp +====================== + +Supported chips: + * All Intel Core family + Prefix: 'coretemp' + CPUID: family 0x6, models 0xe (Pentium M DC), 0xf (Core 2 DC 65nm), + 0x16 (Core 2 SC 65nm), 0x17 (Penryn 45nm), + 0x1a (Nehalem), 0x1c (Atom), 0x1e (Lynnfield), + 0x26 (Tunnel Creek Atom), 0x27 (Medfield Atom), + 0x36 (Cedar Trail Atom) + Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual + Volume 3A: System Programming Guide + http://softwarecommunity.intel.com/Wiki/Mobility/720.htm + +Author: Rudolf Marek + +Description +----------- +This driver permits reading the DTS (Digital Temperature Sensor) embedded +inside Intel CPUs. This driver can read both the per-core and per-package +temperature using the appropriate sensors. The per-package sensor is new; +as of now, it is present only in the SandyBridge platform. The driver will +show the temperature of all cores inside a package under a single device +directory inside hwmon. + +Temperature is measured in degrees Celsius and measurement resolution is +1 degree C. Valid temperatures are from 0 to TjMax degrees C, because +the actual value of temperature register is in fact a delta from TjMax. + +Temperature known as TjMax is the maximum junction temperature of processor, +which depends on the CPU model. See table below. At this temperature, protection +mechanism will perform actions to forcibly cool down the processor. Alarm +may be raised, if the temperature grows enough (more than TjMax) to trigger +the Out-Of-Spec bit. Following table summarizes the exported sysfs files: + +All Sysfs entries are named with their core_id (represented here by 'X'). +tempX_input - Core temperature (in millidegrees Celsius). +tempX_max - All cooling devices should be turned on (on Core2). +tempX_crit - Maximum junction temperature (in millidegrees Celsius). +tempX_crit_alarm - Set when Out-of-spec bit is set, never clears. + Correct CPU operation is no longer guaranteed. +tempX_label - Contains string "Core X", where X is processor + number. For Package temp, this will be "Physical id Y", + where Y is the package number. + +On CPU models which support it, TjMax is read from a model-specific register. +On other models, it is set to an arbitrary value based on weak heuristics. +If these heuristics don't work for you, you can pass the correct TjMax value +as a module parameter (tjmax). + +Appendix A. Known TjMax lists (TBD): +Some information comes from ark.intel.com + +Process Processor TjMax(C) + +22nm Core i5/i7 Processors + i7 3920XM, 3820QM, 3720QM, 3667U, 3520M 105 + i5 3427U, 3360M/3320M 105 + i7 3770/3770K 105 + i5 3570/3570K, 3550, 3470/3450 105 + i7 3770S 103 + i5 3570S/3550S, 3475S/3470S/3450S 103 + i7 3770T 94 + i5 3570T 94 + i5 3470T 91 + +32nm Core i3/i5/i7 Processors + i7 2600 98 + i7 660UM/640/620, 640LM/620, 620M, 610E 105 + i5 540UM/520/430, 540M/520/450/430 105 + i3 330E, 370M/350/330 90 rPGA, 105 BGA + i3 330UM 105 + +32nm Core i7 Extreme Processors + 980X 100 + +32nm Celeron Processors + U3400 105 + P4505/P4500 90 + +32nm Atom Processors + S1260/1220 95 + S1240 102 + Z2460 90 + Z2760 90 + D2700/2550/2500 100 + N2850/2800/2650/2600 100 + +45nm Xeon Processors 5400 Quad-Core + X5492, X5482, X5472, X5470, X5460, X5450 85 + E5472, E5462, E5450/40/30/20/10/05 85 + L5408 95 + L5430, L5420, L5410 70 + +45nm Xeon Processors 5200 Dual-Core + X5282, X5272, X5270, X5260 90 + E5240 90 + E5205, E5220 70, 90 + L5240 70 + L5238, L5215 95 + +45nm Atom Processors + D525/510/425/410 100 + K525/510/425/410 100 + Z670/650 90 + Z560/550/540/530P/530/520PT/520/515/510PT/510P 90 + Z510/500 90 + N570/550 100 + N475/470/455/450 100 + N280/270 90 + 330/230 125 + E680/660/640/620 90 + E680T/660T/640T/620T 110 + E665C/645C 90 + E665CT/645CT 110 + CE4170/4150/4110 110 + CE4200 series unknown + CE5300 series unknown + +45nm Core2 Processors + Solo ULV SU3500/3300 100 + T9900/9800/9600/9550/9500/9400/9300/8300/8100 105 + T6670/6500/6400 105 + T6600 90 + SU9600/9400/9300 105 + SP9600/9400 105 + SL9600/9400/9380/9300 105 + P9700/9600/9500/8800/8700/8600/8400/7570 105 + P7550/7450 90 + +45nm Core2 Quad Processors + Q9100/9000 100 + +45nm Core2 Extreme Processors + X9100/9000 105 + QX9300 100 + +45nm Core i3/i5/i7 Processors + i7 940XM/920 100 + i7 840QM/820/740/720 100 + +45nm Celeron Processors + SU2300 100 + 900 105 + +65nm Core2 Duo Processors + Solo U2200, U2100 100 + U7700/7600/7500 100 + T7800/7700/7600/7500/7400/7300/7250/7200/7100 100 + T5870/5670/5600/5550/5500/5470/5450/5300/5270 100 + T5250 100 + T5800/5750/5200 85 + L7700/7500/7400/7300/7200 100 + +65nm Core2 Extreme Processors + X7900/7800 100 + +65nm Core Duo Processors + U2500/2400 100 + T2700/2600/2450/2400/2350/2300E/2300/2250/2050 100 + L2500/2400/2300 100 + +65nm Core Solo Processors + U1500/1400/1300 100 + T1400/1350/1300/1250 100 + +65nm Xeon Processors 5000 Quad-Core + X5000 90-95 + E5000 80 + L5000 70 + L5318 95 + +65nm Xeon Processors 5000 Dual-Core + 5080, 5063, 5060, 5050, 5030 80-90 + 5160, 5150, 5148, 5140, 5130, 5120, 5110 80 + L5138 100 + +65nm Celeron Processors + T1700/1600 100 + 560/550/540/530 100 diff --git a/Documentation/hwmon/da9052 b/Documentation/hwmon/da9052 new file mode 100644 index 00000000000..5bc51346b68 --- /dev/null +++ b/Documentation/hwmon/da9052 @@ -0,0 +1,61 @@ +Supported chips: + * Dialog Semiconductors DA9052-BC and DA9053-AA/Bx PMICs + Prefix: 'da9052' + Datasheet: Datasheet is not publicly available. + +Authors: David Dajun Chen <dchen@diasemi.com> + +Description +----------- + +The DA9052/53 provides an Analogue to Digital Converter (ADC) with 10 bits +resolution and track and hold circuitry combined with an analogue input +multiplexer. The analogue input multiplexer will allow conversion of up to 10 +different inputs. The track and hold circuit ensures stable input voltages at +the input of the ADC during the conversion. + +The ADC is used to measure the following inputs: +Channel 0: VDDOUT - measurement of the system voltage +Channel 1: ICH - internal battery charger current measurement +Channel 2: TBAT - output from the battery NTC +Channel 3: VBAT - measurement of the battery voltage +Channel 4: ADC_IN4 - high impedance input (0 - 2.5V) +Channel 5: ADC_IN5 - high impedance input (0 - 2.5V) +Channel 6: ADC_IN6 - high impedance input (0 - 2.5V) +Channel 7: XY - TSI interface to measure the X and Y voltage of the touch + screen resistive potentiometers +Channel 8: Internal Tjunc. - sense (internal temp. sensor) +Channel 9: VBBAT - measurement of the backup battery voltage + +By using sysfs attributes we can measure the system voltage VDDOUT, the battery +charging current ICH, battery temperature TBAT, battery junction temperature +TJUNC, battery voltage VBAT and the back up battery voltage VBBAT. + +Voltage Monitoring +------------------ + +Voltages are sampled by a 10 bit ADC. + +The battery voltage is calculated as: + Milli volt = ((ADC value * 1000) / 512) + 2500 + +The backup battery voltage is calculated as: + Milli volt = (ADC value * 2500) / 512; + +The voltages on ADC channels 4, 5 and 6 are calculated as: + Milli volt = (ADC value * 2500) / 1023 + +Temperature Monitoring +---------------------- + +Temperatures are sampled by a 10 bit ADC. Junction and battery temperatures +are monitored by the ADC channels. + +The junction temperature is calculated: + Degrees celsius = 1.708 * (TJUNC_RES - T_OFFSET) - 108.8 +The junction temperature attribute is supported by the driver. + +The battery temperature is calculated: + Degree Celsius = 1 / (t1 + 1/298)- 273 +where t1 = (1/B)* ln(( ADCval * 2.5)/(R25*ITBAT*255)) +Default values of R25, B, ITBAT are 10e3, 3380 and 50e-6 respectively. diff --git a/Documentation/hwmon/da9055 b/Documentation/hwmon/da9055 new file mode 100644 index 00000000000..855c3f536e0 --- /dev/null +++ b/Documentation/hwmon/da9055 @@ -0,0 +1,47 @@ +Supported chips: + * Dialog Semiconductors DA9055 PMIC + Prefix: 'da9055' + Datasheet: Datasheet is not publicly available. + +Authors: David Dajun Chen <dchen@diasemi.com> + +Description +----------- + +The DA9055 provides an Analogue to Digital Converter (ADC) with 10 bits +resolution and track and hold circuitry combined with an analogue input +multiplexer. The analogue input multiplexer will allow conversion of up to 5 +different inputs. The track and hold circuit ensures stable input voltages at +the input of the ADC during the conversion. + +The ADC is used to measure the following inputs: +Channel 0: VDDOUT - measurement of the system voltage +Channel 1: ADC_IN1 - high impedance input (0 - 2.5V) +Channel 2: ADC_IN2 - high impedance input (0 - 2.5V) +Channel 3: ADC_IN3 - high impedance input (0 - 2.5V) +Channel 4: Internal Tjunc. - sense (internal temp. sensor) + +By using sysfs attributes we can measure the system voltage VDDOUT, +chip junction temperature and auxiliary channels voltages. + +Voltage Monitoring +------------------ + +Voltages are sampled in a AUTO mode it can be manually sampled too and results +are stored in a 10 bit ADC. + +The system voltage is calculated as: + Milli volt = ((ADC value * 1000) / 85) + 2500 + +The voltages on ADC channels 1, 2 and 3 are calculated as: + Milli volt = (ADC value * 1000) / 102 + +Temperature Monitoring +---------------------- + +Temperatures are sampled by a 10 bit ADC. Junction temperatures +are monitored by the ADC channels. + +The junction temperature is calculated: + Degrees celsius = -0.4084 * (ADC_RES - T_OFFSET) + 307.6332 +The junction temperature attribute is supported by the driver. diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737 new file mode 100644 index 00000000000..4d2935145a1 --- /dev/null +++ b/Documentation/hwmon/dme1737 @@ -0,0 +1,328 @@ +Kernel driver dme1737 +===================== + +Supported chips: + * SMSC DME1737 and compatibles (like Asus A8000) + Prefix: 'dme1737' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: Provided by SMSC upon request and under NDA + * SMSC SCH3112, SCH3114, SCH3116 + Prefix: 'sch311x' + Addresses scanned: none, address read from Super-I/O config space + Datasheet: Available on the Internet + * SMSC SCH5027 + Prefix: 'sch5027' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: Provided by SMSC upon request and under NDA + * SMSC SCH5127 + Prefix: 'sch5127' + Addresses scanned: none, address read from Super-I/O config space + Datasheet: Provided by SMSC upon request and under NDA + +Authors: + Juerg Haefliger <juergh@gmail.com> + + +Module Parameters +----------------- + +* force_start: bool Enables the monitoring of voltage, fan and temp inputs + and PWM output control functions. Using this parameter + shouldn't be required since the BIOS usually takes care + of this. +* probe_all_addr: bool Include non-standard LPC addresses 0x162e and 0x164e + when probing for ISA devices. This is required for the + following boards: + - VIA EPIA SN18000 + + +Description +----------- + +This driver implements support for the hardware monitoring capabilities of the +SMSC DME1737 and Asus A8000 (which are the same), SMSC SCH5027, SCH311x, +and SCH5127 Super-I/O chips. These chips feature monitoring of 3 temp sensors +temp[1-3] (2 remote diodes and 1 internal), 8 voltages in[0-7] (7 external and +1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement +up to 5 PWM outputs pwm[1-3,5-6] for controlling fan speeds both manually and +automatically. + +For the DME1737, A8000 and SCH5027, fan[1-2] and pwm[1-2] are always present. +Fan[3-6] and pwm[3,5-6] are optional features and their availability depends on +the configuration of the chip. The driver will detect which features are +present during initialization and create the sysfs attributes accordingly. + +For the SCH311x and SCH5127, fan[1-3] and pwm[1-3] are always present and +fan[4-6] and pwm[5-6] don't exist. + +The hardware monitoring features of the DME1737, A8000, and SCH5027 are only +accessible via SMBus, while the SCH311x and SCH5127 only provide access via +the ISA bus. The driver will therefore register itself as an I2C client driver +if it detects a DME1737, A8000, or SCH5027 and as a platform driver if it +detects a SCH311x or SCH5127 chip. + + +Voltage Monitoring +------------------ + +The voltage inputs are sampled with 12-bit resolution and have internal +scaling resistors. The values returned by the driver therefore reflect true +millivolts and don't need scaling. The voltage inputs are mapped as follows +(the last column indicates the input ranges): + +DME1737, A8000: + in0: +5VTR (+5V standby) 0V - 6.64V + in1: Vccp (processor core) 0V - 3V + in2: VCC (internal +3.3V) 0V - 4.38V + in3: +5V 0V - 6.64V + in4: +12V 0V - 16V + in5: VTR (+3.3V standby) 0V - 4.38V + in6: Vbat (+3.0V) 0V - 4.38V + +SCH311x: + in0: +2.5V 0V - 3.32V + in1: Vccp (processor core) 0V - 2V + in2: VCC (internal +3.3V) 0V - 4.38V + in3: +5V 0V - 6.64V + in4: +12V 0V - 16V + in5: VTR (+3.3V standby) 0V - 4.38V + in6: Vbat (+3.0V) 0V - 4.38V + +SCH5027: + in0: +5VTR (+5V standby) 0V - 6.64V + in1: Vccp (processor core) 0V - 3V + in2: VCC (internal +3.3V) 0V - 4.38V + in3: V2_IN 0V - 1.5V + in4: V1_IN 0V - 1.5V + in5: VTR (+3.3V standby) 0V - 4.38V + in6: Vbat (+3.0V) 0V - 4.38V + +SCH5127: + in0: +2.5 0V - 3.32V + in1: Vccp (processor core) 0V - 3V + in2: VCC (internal +3.3V) 0V - 4.38V + in3: V2_IN 0V - 1.5V + in4: V1_IN 0V - 1.5V + in5: VTR (+3.3V standby) 0V - 4.38V + in6: Vbat (+3.0V) 0V - 4.38V + in7: Vtrip (+1.5V) 0V - 1.99V + +Each voltage input has associated min and max limits which trigger an alarm +when crossed. + + +Temperature Monitoring +---------------------- + +Temperatures are measured with 12-bit resolution and reported in millidegree +Celsius. The chip also features offsets for all 3 temperature inputs which - +when programmed - get added to the input readings. The chip does all the +scaling by itself and the driver therefore reports true temperatures that don't +need any user-space adjustments. The temperature inputs are mapped as follows +(the last column indicates the input ranges): + + temp1: Remote diode 1 (3904 type) temperature -127C - +127C + temp2: DME1737 internal temperature -127C - +127C + temp3: Remote diode 2 (3904 type) temperature -127C - +127C + +Each temperature input has associated min and max limits which trigger an alarm +when crossed. Additionally, each temperature input has a fault attribute that +returns 1 when a faulty diode or an unconnected input is detected and 0 +otherwise. + + +Fan Monitoring +-------------- + +Fan RPMs are measured with 16-bit resolution. The chip provides inputs for 6 +fan tachometers. All 6 inputs have an associated min limit which triggers an +alarm when crossed. Fan inputs 1-4 provide type attributes that need to be set +to the number of pulses per fan revolution that the connected tachometer +generates. Supported values are 1, 2, and 4. Fan inputs 5-6 only support fans +that generate 2 pulses per revolution. Fan inputs 5-6 also provide a max +attribute that needs to be set to the maximum attainable RPM (fan at 100% duty- +cycle) of the input. The chip adjusts the sampling rate based on this value. + + +PWM Output Control +------------------ + +This chip features 5 PWM outputs. PWM outputs 1-3 are associated with fan +inputs 1-3 and PWM outputs 5-6 are associated with fan inputs 5-6. PWM outputs +1-3 can be configured to operate either in manual or automatic mode by setting +the appropriate enable attribute accordingly. PWM outputs 5-6 can only operate +in manual mode, their enable attributes are therefore read-only. When set to +manual mode, the fan speed is set by writing the duty-cycle value to the +appropriate PWM attribute. In automatic mode, the PWM attribute returns the +current duty-cycle as set by the fan controller in the chip. All PWM outputs +support the setting of the output frequency via the freq attribute. + +In automatic mode, the chip supports the setting of the PWM ramp rate which +defines how fast the PWM output is adjusting to changes of the associated +temperature input. Associating PWM outputs to temperature inputs is done via +temperature zones. The chip features 3 zones whose assignments to temperature +inputs is static and determined during initialization. These assignments can +be retrieved via the zone[1-3]_auto_channels_temp attributes. Each PWM output +is assigned to one (or hottest of multiple) temperature zone(s) through the +pwm[1-3]_auto_channels_zone attributes. Each PWM output has 3 distinct output +duty-cycles: full, low, and min. Full is internally hard-wired to 255 (100%) +and low and min can be programmed via pwm[1-3]_auto_point1_pwm and +pwm[1-3]_auto_pwm_min, respectively. The thermal thresholds of the zones are +programmed via zone[1-3]_auto_point[1-3]_temp and +zone[1-3]_auto_point1_temp_hyst: + + pwm[1-3]_auto_point2_pwm full-speed duty-cycle (255, i.e., 100%) + pwm[1-3]_auto_point1_pwm low-speed duty-cycle + pwm[1-3]_auto_pwm_min min-speed duty-cycle + + zone[1-3]_auto_point3_temp full-speed temp (all outputs) + zone[1-3]_auto_point2_temp full-speed temp + zone[1-3]_auto_point1_temp low-speed temp + zone[1-3]_auto_point1_temp_hyst min-speed temp + +The chip adjusts the output duty-cycle linearly in the range of auto_point1_pwm +to auto_point2_pwm if the temperature of the associated zone is between +auto_point1_temp and auto_point2_temp. If the temperature drops below the +auto_point1_temp_hyst value, the output duty-cycle is set to the auto_pwm_min +value which only supports two values: 0 or auto_point1_pwm. That means that the +fan either turns completely off or keeps spinning with the low-speed +duty-cycle. If any of the temperatures rise above the auto_point3_temp value, +all PWM outputs are set to 100% duty-cycle. + +Following is another representation of how the chip sets the output duty-cycle +based on the temperature of the associated thermal zone: + + Duty-Cycle Duty-Cycle + Temperature Rising Temp Falling Temp + ----------- ----------- ------------ + full-speed full-speed full-speed + + < linearly adjusted duty-cycle > + + low-speed low-speed low-speed + min-speed low-speed + min-speed min-speed min-speed + min-speed min-speed + + +Sysfs Attributes +---------------- + +Following is a list of all sysfs attributes that the driver provides, their +permissions and a short description: + +Name Perm Description +---- ---- ----------- +cpu0_vid RO CPU core reference voltage in + millivolts. +vrm RW Voltage regulator module version + number. + +in[0-7]_input RO Measured voltage in millivolts. +in[0-7]_min RW Low limit for voltage input. +in[0-7]_max RW High limit for voltage input. +in[0-7]_alarm RO Voltage input alarm. Returns 1 if + voltage input is or went outside the + associated min-max range, 0 otherwise. + +temp[1-3]_input RO Measured temperature in millidegree + Celsius. +temp[1-3]_min RW Low limit for temp input. +temp[1-3]_max RW High limit for temp input. +temp[1-3]_offset RW Offset for temp input. This value will + be added by the chip to the measured + temperature. +temp[1-3]_alarm RO Alarm for temp input. Returns 1 if temp + input is or went outside the associated + min-max range, 0 otherwise. +temp[1-3]_fault RO Temp input fault. Returns 1 if the chip + detects a faulty thermal diode or an + unconnected temp input, 0 otherwise. + +zone[1-3]_auto_channels_temp RO Temperature zone to temperature input + mapping. This attribute is a bitfield + and supports the following values: + 1: temp1 + 2: temp2 + 4: temp3 +zone[1-3]_auto_point1_temp_hyst RW Auto PWM temp point1 hysteresis. The + output of the corresponding PWM is set + to the pwm_auto_min value if the temp + falls below the auto_point1_temp_hyst + value. +zone[1-3]_auto_point[1-3]_temp RW Auto PWM temp points. Auto_point1 is + the low-speed temp, auto_point2 is the + full-speed temp, and auto_point3 is the + temp at which all PWM outputs are set + to full-speed (100% duty-cycle). + +fan[1-6]_input RO Measured fan speed in RPM. +fan[1-6]_min RW Low limit for fan input. +fan[1-6]_alarm RO Alarm for fan input. Returns 1 if fan + input is or went below the associated + min value, 0 otherwise. +fan[1-4]_type RW Type of attached fan. Expressed in + number of pulses per revolution that + the fan generates. Supported values are + 1, 2, and 4. +fan[5-6]_max RW Max attainable RPM at 100% duty-cycle. + Required for chip to adjust the + sampling rate accordingly. + +pmw[1-3,5-6] RO/RW Duty-cycle of PWM output. Supported + values are 0-255 (0%-100%). Only + writeable if the associated PWM is in + manual mode. +pwm[1-3]_enable RW Enable of PWM outputs 1-3. Supported + values are: + 0: turned off (output @ 100%) + 1: manual mode + 2: automatic mode +pwm[5-6]_enable RO Enable of PWM outputs 5-6. Always + returns 1 since these 2 outputs are + hard-wired to manual mode. +pmw[1-3,5-6]_freq RW Frequency of PWM output. Supported + values are in the range 11Hz-30000Hz + (default is 25000Hz). +pmw[1-3]_ramp_rate RW Ramp rate of PWM output. Determines how + fast the PWM duty-cycle will change + when the PWM is in automatic mode. + Expressed in ms per PWM step. Supported + values are in the range 0ms-206ms + (default is 0, which means the duty- + cycle changes instantly). +pwm[1-3]_auto_channels_zone RW PWM output to temperature zone mapping. + This attribute is a bitfield and + supports the following values: + 1: zone1 + 2: zone2 + 4: zone3 + 6: highest of zone[2-3] + 7: highest of zone[1-3] +pwm[1-3]_auto_pwm_min RW Auto PWM min pwm. Minimum PWM duty- + cycle. Supported values are 0 or + auto_point1_pwm. +pwm[1-3]_auto_point1_pwm RW Auto PWM pwm point. Auto_point1 is the + low-speed duty-cycle. +pwm[1-3]_auto_point2_pwm RO Auto PWM pwm point. Auto_point2 is the + full-speed duty-cycle which is hard- + wired to 255 (100% duty-cycle). + +Chip Differences +---------------- + +Feature dme1737 sch311x sch5027 sch5127 +------------------------------------------------------- +temp[1-3]_offset yes yes +vid yes +zone3 yes yes yes +zone[1-3]_hyst yes yes +pwm min/off yes yes +fan3 opt yes opt yes +pwm3 opt yes opt yes +fan4 opt opt +fan5 opt opt +pwm5 opt opt +fan6 opt opt +pwm6 opt opt +in7 yes diff --git a/Documentation/hwmon/ds1621 b/Documentation/hwmon/ds1621 index 1fee6f1e6bc..f775e612f58 100644 --- a/Documentation/hwmon/ds1621 +++ b/Documentation/hwmon/ds1621 @@ -2,22 +2,36 @@ Kernel driver ds1621 ==================== Supported chips: - * Dallas Semiconductor DS1621 + * Dallas Semiconductor / Maxim Integrated DS1621 Prefix: 'ds1621' - Addresses scanned: I2C 0x48 - 0x4f - Datasheet: Publicly available at the Dallas Semiconductor website - http://www.dalsemi.com/ + Addresses scanned: none + Datasheet: Publicly available from www.maximintegrated.com + * Dallas Semiconductor DS1625 - Prefix: 'ds1621' - Addresses scanned: I2C 0x48 - 0x4f - Datasheet: Publicly available at the Dallas Semiconductor website - http://www.dalsemi.com/ + Prefix: 'ds1625' + Addresses scanned: none + Datasheet: Publicly available from www.datasheetarchive.com + + * Maxim Integrated DS1631 + Prefix: 'ds1631' + Addresses scanned: none + Datasheet: Publicly available from www.maximintegrated.com + + * Maxim Integrated DS1721 + Prefix: 'ds1721' + Addresses scanned: none + Datasheet: Publicly available from www.maximintegrated.com + + * Maxim Integrated DS1731 + Prefix: 'ds1731' + Addresses scanned: none + Datasheet: Publicly available from www.maximintegrated.com Authors: Christian W. Zuckschwerdt <zany@triq.net> valuable contributions by Jan M. Sendler <sendler@sendler.de> ported to 2.6 by Aurelien Jarno <aurelien@aurel32.net> - with the help of Jean Delvare <khali@linux-fr.org> + with the help of Jean Delvare <jdelvare@suse.de> Module Parameters ------------------ @@ -49,12 +63,9 @@ of up to +/- 0.5 degrees even when compared against precise temperature readings. Be sure to have a high vs. low temperature limit gap of al least 1.0 degree Celsius to avoid Tout "bouncing", though! -As for alarms, you can read the alarm status of the DS1621 via the 'alarms' -/sys file interface. The result consists mainly of bit 6 and 5 of the -configuration register of the chip; bit 6 (0x40 or 64) is the high alarm -bit and bit 5 (0x20 or 32) the low one. These bits are set when the high or -low limits are met or exceeded and are reset by the module as soon as the -respective temperature ranges are left. +The alarm bits are set when the high or low limits are met or exceeded and +are reset by the module as soon as the respective temperature ranges are +left. The alarm registers are in no way suitable to find out about the actual status of Tout. They will only tell you about its history, whether or not @@ -62,47 +73,115 @@ any of the limits have ever been met or exceeded since last power-up or reset. Be aware: When testing, it showed that the status of Tout can change with neither of the alarms set. -Temperature conversion of the DS1621 takes up to 1000ms; internal access to -non-volatile registers may last for 10ms or below. - -High Accuracy Temperature Reading ---------------------------------- - -As said before, the temperature issued via the 9-bit i2c-bus data is -somewhat arbitrary. Internally, the temperature conversion is of a -different kind that is explained (not so...) well in the DS1621 data sheet. -To cut the long story short: Inside the DS1621 there are two oscillators, -both of them biassed by a temperature coefficient. - -Higher resolution of the temperature reading can be achieved using the -internal projection, which means taking account of REG_COUNT and REG_SLOPE -(the driver manages them): - -Taken from Dallas Semiconductors App Note 068: 'Increasing Temperature -Resolution on the DS1620' and App Note 105: 'High Resolution Temperature -Measurement with Dallas Direct-to-Digital Temperature Sensors' - -- Read the 9-bit temperature and strip the LSB (Truncate the .5 degs) -- The resulting value is TEMP_READ. -- Then, read REG_COUNT. -- And then, REG_SLOPE. - - TEMP = TEMP_READ - 0.25 + ((REG_SLOPE - REG_COUNT) / REG_SLOPE) - -Note that this is what the DONE bit in the DS1621 configuration register is -good for: Internally, one temperature conversion takes up to 1000ms. Before -that conversion is complete you will not be able to read valid things out -of REG_COUNT and REG_SLOPE. The DONE bit, as you may have guessed by now, -tells you whether the conversion is complete ("done", in plain English) and -thus, whether the values you read are good or not. - -The DS1621 has two modes of operation: "Continuous" conversion, which can -be understood as the default stand-alone mode where the chip gets the -temperature and controls external devices via its Tout pin or tells other -i2c's about it if they care. The other mode is called "1SHOT", that means -that it only figures out about the temperature when it is explicitly told -to do so; this can be seen as power saving mode. - -Now if you want to read REG_COUNT and REG_SLOPE, you have to either stop -the continuous conversions until the contents of these registers are valid, -or, in 1SHOT mode, you have to have one conversion made. +Since there is no version or vendor identification register, there is +no unique identification for these devices. Therefore, explicit device +instantiation is required for correct device identification and functionality +(one device per address in this address range: 0x48..0x4f). + +The DS1625 is pin compatible and functionally equivalent with the DS1621, +but the DS1621 is meant to replace it. The DS1631, DS1721, and DS1731 are +also pin compatible with the DS1621 and provide multi-resolution support. + +Additionally, the DS1721 data sheet says the temperature flags (THF and TLF) +are used internally, however, these flags do get set and cleared as the actual +temperature crosses the min or max settings (which by default are set to 75 +and 80 degrees respectively). + +Temperature Conversion: +----------------------- +DS1621 - 750ms (older devices may take up to 1000ms) +DS1625 - 500ms +DS1631 - 93ms..750ms for 9..12 bits resolution, respectively. +DS1721 - 93ms..750ms for 9..12 bits resolution, respectively. +DS1731 - 93ms..750ms for 9..12 bits resolution, respectively. + +Note: +On the DS1621, internal access to non-volatile registers may last for 10ms +or less (unverified on the other devices). + +Temperature Accuracy: +--------------------- +DS1621: +/- 0.5 degree Celsius (from 0 to +70 degrees) +DS1625: +/- 0.5 degree Celsius (from 0 to +70 degrees) +DS1631: +/- 0.5 degree Celsius (from 0 to +70 degrees) +DS1721: +/- 1.0 degree Celsius (from -10 to +85 degrees) +DS1731: +/- 1.0 degree Celsius (from -10 to +85 degrees) + +Note: +Please refer to the device datasheets for accuracy at other temperatures. + +Temperature Resolution: +----------------------- +As mentioned above, the DS1631, DS1721, and DS1731 provide multi-resolution +support, which is achieved via the R0 and R1 config register bits, where: + +R0..R1 +------ + 0 0 => 9 bits, 0.5 degrees Celcius + 1 0 => 10 bits, 0.25 degrees Celcius + 0 1 => 11 bits, 0.125 degrees Celcius + 1 1 => 12 bits, 0.0625 degrees Celcius + +Note: +At initial device power-on, the default resolution is set to 12-bits. + +The resolution mode for the DS1631, DS1721, or DS1731 can be changed from +userspace, via the device 'update_interval' sysfs attribute. This attribute +will normalize the range of input values to the device maximum resolution +values defined in the datasheet as follows: + +Resolution Conversion Time Input Range + (C/LSB) (msec) (msec) +------------------------------------------------ +0.5 93.75 0....94 +0.25 187.5 95...187 +0.125 375 188..375 +0.0625 750 376..infinity +------------------------------------------------ + +The following examples show how the 'update_interval' attribute can be +used to change the conversion time: + +$ cat update_interval +750 +$ cat temp1_input +22062 +$ +$ echo 300 > update_interval +$ cat update_interval +375 +$ cat temp1_input +22125 +$ +$ echo 150 > update_interval +$ cat update_interval +188 +$ cat temp1_input +22250 +$ +$ echo 1 > update_interval +$ cat update_interval +94 +$ cat temp1_input +22000 +$ +$ echo 1000 > update_interval +$ cat update_interval +750 +$ cat temp1_input +22062 +$ + +As shown, the ds1621 driver automatically adjusts the 'update_interval' +user input, via a step function. Reading back the 'update_interval' value +after a write operation provides the conversion time used by the device. + +Mathematically, the resolution can be derived from the conversion time +via the following function: + + g(x) = 0.5 * [minimum_conversion_time/x] + +where: + -> 'x' = the output from 'update_interval' + -> 'g(x)' = the resolution in degrees C per LSB. + -> 93.75ms = minimum conversion time diff --git a/Documentation/hwmon/ds620 b/Documentation/hwmon/ds620 new file mode 100644 index 00000000000..1fbe3cd916c --- /dev/null +++ b/Documentation/hwmon/ds620 @@ -0,0 +1,34 @@ +Kernel driver ds620 +=================== + +Supported chips: + * Dallas Semiconductor DS620 + Prefix: 'ds620' + Datasheet: Publicly available at the Dallas Semiconductor website + http://www.dalsemi.com/ + +Authors: + Roland Stigge <stigge@antcom.de> + based on ds1621.c by + Christian W. Zuckschwerdt <zany@triq.net> + +Description +----------- + +The DS620 is a (one instance) digital thermometer and thermostat. It has both +high and low temperature limits which can be user defined (i.e. programmed +into non-volatile on-chip registers). Temperature range is -55 degree Celsius +to +125. Between 0 and 70 degree Celsius, accuracy is 0.5 Kelvin. The value +returned via sysfs displays post decimal positions. + +The thermostat function works as follows: When configured via platform_data +(struct ds620_platform_data) .pomode == 0 (default), the thermostat output pin +PO is always low. If .pomode == 1, the thermostat is in PO_LOW mode. I.e., the +output pin PO becomes active when the temperature falls below temp1_min and +stays active until the temperature goes above temp1_max. + +Likewise, with .pomode == 2, the thermostat is in PO_HIGH mode. I.e., the PO +output pin becomes active when the temperature goes above temp1_max and stays +active until the temperature falls below temp1_min. + +The PO output pin of the DS620 operates active-low. diff --git a/Documentation/hwmon/emc1403 b/Documentation/hwmon/emc1403 new file mode 100644 index 00000000000..a869b0ef6a9 --- /dev/null +++ b/Documentation/hwmon/emc1403 @@ -0,0 +1,59 @@ +Kernel driver emc1403 +===================== + +Supported chips: + * SMSC / Microchip EMC1402, EMC1412 + Addresses scanned: I2C 0x18, 0x1c, 0x29, 0x4c, 0x4d, 0x5c + Prefix: 'emc1402' + Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/1412.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/1402.pdf + * SMSC / Microchip EMC1403, EMC1404, EMC1413, EMC1414 + Addresses scanned: I2C 0x18, 0x29, 0x4c, 0x4d + Prefix: 'emc1403', 'emc1404' + Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/1403_1404.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/1413_1414.pdf + * SMSC / Microchip EMC1422 + Addresses scanned: I2C 0x4c + Prefix: 'emc1422' + Datasheet: + http://ww1.microchip.com/downloads/en/DeviceDoc/1422.pdf + * SMSC / Microchip EMC1423, EMC1424 + Addresses scanned: I2C 0x4c + Prefix: 'emc1423', 'emc1424' + Datasheet: + http://ww1.microchip.com/downloads/en/DeviceDoc/1423_1424.pdf + +Author: + Kalhan Trisal <kalhan.trisal@intel.com + + +Description +----------- + +The Standard Microsystems Corporation (SMSC) / Microchip EMC14xx chips +contain up to four temperature sensors. EMC14x2 support two sensors +(one internal, one external). EMC14x3 support three sensors (one internal, +two external), and EMC14x4 support four sensors (one internal, three +external). + +The chips implement three limits for each sensor: low (tempX_min), high +(tempX_max) and critical (tempX_crit.) The chips also implement an +hysteresis mechanism which applies to all limits. The relative difference +is stored in a single register on the chip, which means that the relative +difference between the limit and its hysteresis is always the same for +all three limits. + +This implementation detail implies the following: +* When setting a limit, its hysteresis will automatically follow, the + difference staying unchanged. For example, if the old critical limit + was 80 degrees C, and the hysteresis was 75 degrees C, and you change + the critical limit to 90 degrees C, then the hysteresis will + automatically change to 85 degrees C. +* The hysteresis values can't be set independently. We decided to make + only temp1_crit_hyst writable, while all other hysteresis attributes + are read-only. Setting temp1_crit_hyst writes the difference between + temp1_crit_hyst and temp1_crit into the chip, and the same relative + hysteresis applies automatically to all other limits. +* The limits should be set before the hysteresis. diff --git a/Documentation/hwmon/emc2103 b/Documentation/hwmon/emc2103 new file mode 100644 index 00000000000..a12b2c12714 --- /dev/null +++ b/Documentation/hwmon/emc2103 @@ -0,0 +1,33 @@ +Kernel driver emc2103 +====================== + +Supported chips: + * SMSC EMC2103 + Addresses scanned: I2C 0x2e + Prefix: 'emc2103' + Datasheet: Not public + +Authors: + Steve Glendinning <steve.glendinning@smsc.com> + +Description +----------- + +The Standard Microsystems Corporation (SMSC) EMC2103 chips +contain up to 4 temperature sensors and a single fan controller. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4 or 8) to give +the readings more range or accuracy. Not all RPM values can accurately be +represented, so some rounding is done. With a divider of 1, the lowest +representable value is 480 RPM. + +This driver supports RPM based control, to use this a fan target +should be written to fan1_target and pwm1_enable should be set to 3. + +The 2103-2 and 2103-4 variants have a third temperature sensor, which can +be connected to two anti-parallel diodes. These values can be read +as temp3 and temp4. If only one diode is attached to this channel, temp4 +will show as "fault". The module parameter "apd=0" can be used to suppress +this 4th channel when anti-parallel diodes are not fitted. diff --git a/Documentation/hwmon/emc6w201 b/Documentation/hwmon/emc6w201 new file mode 100644 index 00000000000..757629b1289 --- /dev/null +++ b/Documentation/hwmon/emc6w201 @@ -0,0 +1,42 @@ +Kernel driver emc6w201 +====================== + +Supported chips: + * SMSC EMC6W201 + Prefix: 'emc6w201' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: Not public + +Author: Jean Delvare <jdelvare@suse.de> + + +Description +----------- + +From the datasheet: + +"The EMC6W201 is an environmental monitoring device with automatic fan +control capability and enhanced system acoustics for noise suppression. +This ACPI compliant device provides hardware monitoring for up to six +voltages (including its own VCC) and five external thermal sensors, +measures the speed of up to five fans, and controls the speed of +multiple DC fans using three Pulse Width Modulator (PWM) outputs. Note +that it is possible to control more than three fans by connecting two +fans to one PWM output. The EMC6W201 will be available in a 36-pin +QFN package." + +The device is functionally close to the EMC6D100 series, but is +register-incompatible. + +The driver currently only supports the monitoring of the voltages, +temperatures and fan speeds. Limits can be changed. Alarms are not +supported, and neither is fan speed control. + + +Known Systems With EMC6W201 +--------------------------- + +The EMC6W201 is a rare device, only found on a few systems, made in +2005 and 2006. Known systems with this device: +* Dell Precision 670 workstation +* Gigabyte 2CEWH mainboard diff --git a/Documentation/hwmon/f71805f b/Documentation/hwmon/f71805f new file mode 100644 index 00000000000..48a356084bc --- /dev/null +++ b/Documentation/hwmon/f71805f @@ -0,0 +1,167 @@ +Kernel driver f71805f +===================== + +Supported chips: + * Fintek F71805F/FG + Prefix: 'f71805f' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71806F/FG + Prefix: 'f71872f' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71872F/FG + Prefix: 'f71872f' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + +Author: Jean Delvare <jdelvare@suse.de> + +Thanks to Denis Kieft from Barracuda Networks for the donation of a +test system (custom Jetway K8M8MS motherboard, with CPU and RAM) and +for providing initial documentation. + +Thanks to Kris Chen and Aaron Huang from Fintek for answering technical +questions and providing additional documentation. + +Thanks to Chris Lin from Jetway for providing wiring schematics and +answering technical questions. + + +Description +----------- + +The Fintek F71805F/FG Super I/O chip includes complete hardware monitoring +capabilities. It can monitor up to 9 voltages (counting its own power +source), 3 fans and 3 temperature sensors. + +This chip also has fan controlling features, using either DC or PWM, in +three different modes (one manual, two automatic). + +The Fintek F71872F/FG Super I/O chip is almost the same, with two +additional internal voltages monitored (VSB and battery). It also features +6 VID inputs. The VID inputs are not yet supported by this driver. + +The Fintek F71806F/FG Super-I/O chip is essentially the same as the +F71872F/FG, and is undistinguishable therefrom. + +The driver assumes that no more than one chip is present, which seems +reasonable. + + +Voltage Monitoring +------------------ + +Voltages are sampled by an 8-bit ADC with a LSB of 8 mV. The supported +range is thus from 0 to 2.040 V. Voltage values outside of this range +need external resistors. An exception is in0, which is used to monitor +the chip's own power source (+3.3V), and is divided internally by a +factor 2. For the F71872F/FG, in9 (VSB) and in10 (battery) are also +divided internally by a factor 2. + +The two LSB of the voltage limit registers are not used (always 0), so +you can only set the limits in steps of 32 mV (before scaling). + +The wirings and resistor values suggested by Fintek are as follow: + + pin expected + name use R1 R2 divider raw val. + +in0 VCC VCC3.3V int. int. 2.00 1.65 V +in1 VIN1 VTT1.2V 10K - 1.00 1.20 V +in2 VIN2 VRAM 100K 100K 2.00 ~1.25 V (1) +in3 VIN3 VCHIPSET 47K 100K 1.47 2.24 V (2) +in4 VIN4 VCC5V 200K 47K 5.25 0.95 V +in5 VIN5 +12V 200K 20K 11.00 1.05 V +in6 VIN6 VCC1.5V 10K - 1.00 1.50 V +in7 VIN7 VCORE 10K - 1.00 ~1.40 V (1) +in8 VIN8 VSB5V 200K 47K 1.00 0.95 V +in10 VSB VSB3.3V int. int. 2.00 1.65 V (3) +in9 VBAT VBATTERY int. int. 2.00 1.50 V (3) + +(1) Depends on your hardware setup. +(2) Obviously not correct, swapping R1 and R2 would make more sense. +(3) F71872F/FG only. + +These values can be used as hints at best, as motherboard manufacturers +are free to use a completely different setup. As a matter of fact, the +Jetway K8M8MS uses a significantly different setup. You will have to +find out documentation about your own motherboard, and edit sensors.conf +accordingly. + +Each voltage measured has associated low and high limits, each of which +triggers an alarm when crossed. + + +Fan Monitoring +-------------- + +Fan rotation speeds are reported as 12-bit values from a gated clock +signal. Speeds down to 366 RPM can be measured. There is no theoretical +high limit, but values over 6000 RPM seem to cause problem. The effective +resolution is much lower than you would expect, the step between different +register values being 10 rather than 1. + +The chip assumes 2 pulse-per-revolution fans. + +An alarm is triggered if the rotation speed drops below a programmable +limit or is too low to be measured. + + +Temperature Monitoring +---------------------- + +Temperatures are reported in degrees Celsius. Each temperature measured +has a high limit, those crossing triggers an alarm. There is an associated +hysteresis value, below which the temperature has to drop before the +alarm is cleared. + +All temperature channels are external, there is no embedded temperature +sensor. Each channel can be used for connecting either a thermal diode +or a thermistor. The driver reports the currently selected mode, but +doesn't allow changing it. In theory, the BIOS should have configured +everything properly. + + +Fan Control +----------- + +Both PWM (pulse-width modulation) and DC fan speed control methods are +supported. The right one to use depends on external circuitry on the +motherboard, so the driver assumes that the BIOS set the method +properly. The driver will report the method, but won't let you change +it. + +When the PWM method is used, you can select the operating frequency, +from 187.5 kHz (default) to 31 Hz. The best frequency depends on the +fan model. As a rule of thumb, lower frequencies seem to give better +control, but may generate annoying high-pitch noise. So a frequency just +above the audible range, such as 25 kHz, may be a good choice; if this +doesn't give you good linear control, try reducing it. Fintek recommends +not going below 1 kHz, as the fan tachometers get confused by lower +frequencies as well. + +When the DC method is used, Fintek recommends not going below 5 V, which +corresponds to a pwm value of 106 for the driver. The driver doesn't +enforce this limit though. + +Three different fan control modes are supported; the mode number is written +to the pwm<n>_enable file. + +* 1: Manual mode + You ask for a specific PWM duty cycle or DC voltage by writing to the + pwm<n> file. + +* 2: Temperature mode + You define 3 temperature/fan speed trip points using the + pwm<n>_auto_point<m>_temp and _fan files. These define a staircase + relationship between temperature and fan speed with two additional points + interpolated between the values that you define. When the temperature + is below auto_point1_temp the fan is switched off. + +* 3: Fan speed mode + You ask for a specific fan speed by writing to the fan<n>_target file. + +Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to +fan2 and pwm3 to fan3. Temperature mode also requires that temp1 corresponds +to pwm1 and fan1, etc. diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg new file mode 100644 index 00000000000..de91c0db584 --- /dev/null +++ b/Documentation/hwmon/f71882fg @@ -0,0 +1,138 @@ +Kernel driver f71882fg +====================== + +Supported chips: + * Fintek F71808E + Prefix: 'f71808e' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public + * Fintek F71808A + Prefix: 'f71808a' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public + * Fintek F71858FG + Prefix: 'f71858fg' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71862FG and F71863FG + Prefix: 'f71862fg' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71869F and F71869E + Prefix: 'f71869' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71869A + Prefix: 'f71869a' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public + * Fintek F71882FG and F71883FG + Prefix: 'f71882fg' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71889FG + Prefix: 'f71889fg' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + * Fintek F71889ED + Prefix: 'f71889ed' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Should become available on the Fintek website soon + * Fintek F71889A + Prefix: 'f71889a' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Should become available on the Fintek website soon + * Fintek F8000 + Prefix: 'f8000' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public + * Fintek F81801U + Prefix: 'f71889fg' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public + Note: This is the 64-pin variant of the F71889FG, they have the + same device ID and are fully compatible as far as hardware + monitoring is concerned. + * Fintek F81865F + Prefix: 'f81865f' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Available from the Fintek website + +Author: Hans de Goede <hdegoede@redhat.com> + + +Description +----------- + +Fintek F718xx/F8000 Super I/O chips include complete hardware monitoring +capabilities. They can monitor up to 9 voltages, 4 fans and 3 temperature +sensors. + +These chips also have fan controlling features, using either DC or PWM, in +three different modes (one manual, two automatic). + +The driver assumes that no more than one chip is present, which seems +reasonable. + + +Monitoring +---------- + +The Voltage, Fan and Temperature Monitoring uses the standard sysfs +interface as documented in sysfs-interface, without any exceptions. + + +Fan Control +----------- + +Both PWM (pulse-width modulation) and DC fan speed control methods are +supported. The right one to use depends on external circuitry on the +motherboard, so the driver assumes that the BIOS set the method +properly. + +Note that the lowest numbered temperature zone trip point corresponds to +to the border between the highest and one but highest temperature zones, and +vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp +to low temp! This is how things are implemented in the IC, and the driver +mimicks this. + +There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC +voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM +mode where the actual RPM of the fan (as measured) is controlled and the speed +gets specified as 0-100% of the fan#_full_speed file. + +Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a +whole lot of a difference when modifying fan control settings. The only +important difference is that in RPM mode the 0-100% controls the fan speed +between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs +RPM mode, it will also set fan#_full_speed properly, if it does not then +fan control will not work properly, unless you set a sane fan#_full_speed +value yourself. + +Switching between these modes requires re-initializing a whole bunch of +registers, so the mode which the BIOS has set is kept. The mode is +printed when loading the driver. + +Three different fan control modes are supported; the mode number is written +to the pwm#_enable file. Note that not all modes are supported on all +chips, and some modes may only be available in RPM / PWM mode. +Writing an unsupported mode will result in an invalid parameter error. + +* 1: Manual mode + You ask for a specific PWM duty cycle / DC voltage or a specific % of + fan#_full_speed by writing to the pwm# file. This mode is only + available on the F71858FG / F8000 if the fan channel is in RPM mode. + +* 2: Normal auto mode + You can define a number of temperature/fan speed trip points, which % the + fan should run at at this temp and which temp a fan should follow using the + standard sysfs interface. The number and type of trip points is chip + depended, see which files are available in sysfs. + Fan/PWM channel 3 of the F8000 is always in this mode! + +* 3: Thermostat mode (Only available on the F8000 when in duty cycle mode) + The fan speed is regulated to keep the temp the fan is mapped to between + temp#_auto_point2_temp and temp#_auto_point3_temp. + +All of the automatic modes require that pwm1 corresponds to fan1, pwm2 to +fan2 and pwm3 to fan3. diff --git a/Documentation/hwmon/fam15h_power b/Documentation/hwmon/fam15h_power new file mode 100644 index 00000000000..80654813d04 --- /dev/null +++ b/Documentation/hwmon/fam15h_power @@ -0,0 +1,37 @@ +Kernel driver fam15h_power +========================== + +Supported chips: +* AMD Family 15h Processors + + Prefix: 'fam15h_power' + Addresses scanned: PCI space + Datasheets: + BIOS and Kernel Developer's Guide (BKDG) For AMD Family 15h Processors + (not yet published) + +Author: Andreas Herrmann <herrmann.der.user@googlemail.com> + +Description +----------- + +This driver permits reading of registers providing power information +of AMD Family 15h processors. + +For AMD Family 15h processors the following power values can be +calculated using different processor northbridge function registers: + +* BasePwrWatts: Specifies in watts the maximum amount of power + consumed by the processor for NB and logic external to the core. +* ProcessorPwrWatts: Specifies in watts the maximum amount of power + the processor can support. +* CurrPwrWatts: Specifies in watts the current amount of power being + consumed by the processor. + +This driver provides ProcessorPwrWatts and CurrPwrWatts: +* power1_crit (ProcessorPwrWatts) +* power1_input (CurrPwrWatts) + +On multi-node processors the calculated value is for the entire +package and not for a single node. Thus the driver creates sysfs +attributes only for internal node0 of a multi-node processor. diff --git a/Documentation/hwmon/fscher b/Documentation/hwmon/fscher deleted file mode 100644 index 64031659aff..00000000000 --- a/Documentation/hwmon/fscher +++ /dev/null @@ -1,169 +0,0 @@ -Kernel driver fscher -==================== - -Supported chips: - * Fujitsu-Siemens Hermes chip - Prefix: 'fscher' - Addresses scanned: I2C 0x73 - -Authors: - Reinhard Nissl <rnissl@gmx.de> based on work - from Hermann Jung <hej@odn.de>, - Frodo Looijaard <frodol@dds.nl>, - Philip Edelbrock <phil@netroedge.com> - -Description ------------ - -This driver implements support for the Fujitsu-Siemens Hermes chip. It is -described in the 'Register Set Specification BMC Hermes based Systemboard' -from Fujitsu-Siemens. - -The Hermes chip implements a hardware-based system management, e.g. for -controlling fan speed and core voltage. There is also a watchdog counter on -the chip which can trigger an alarm and even shut the system down. - -The chip provides three temperature values (CPU, motherboard and -auxiliary), three voltage values (+12V, +5V and battery) and three fans -(power supply, CPU and auxiliary). - -Temperatures are measured in degrees Celsius. The resolution is 1 degree. - -Fan rotation speeds are reported in RPM (rotations per minute). The value -can be divided by a programmable divider (1, 2 or 4) which is stored on -the chip. - -Voltage sensors (also known as "in" sensors) report their values in volts. - -All values are reported as final values from the driver. There is no need -for further calculations. - - -Detailed description --------------------- - -Below you'll find a single line description of all the bit values. With -this information, you're able to decode e. g. alarms, wdog, etc. To make -use of the watchdog, you'll need to set the watchdog time and enable the -watchdog. After that it is necessary to restart the watchdog time within -the specified period of time, or a system reset will occur. - -* revision - READING & 0xff = 0x??: HERMES revision identification - -* alarms - READING & 0x80 = 0x80: CPU throttling active - READING & 0x80 = 0x00: CPU running at full speed - - READING & 0x10 = 0x10: software event (see control:1) - READING & 0x10 = 0x00: no software event - - READING & 0x08 = 0x08: watchdog event (see wdog:2) - READING & 0x08 = 0x00: no watchdog event - - READING & 0x02 = 0x02: thermal event (see temp*:1) - READING & 0x02 = 0x00: no thermal event - - READING & 0x01 = 0x01: fan event (see fan*:1) - READING & 0x01 = 0x00: no fan event - - READING & 0x13 ! 0x00: ALERT LED is flashing - -* control - READING & 0x01 = 0x01: software event - READING & 0x01 = 0x00: no software event - - WRITING & 0x01 = 0x01: set software event - WRITING & 0x01 = 0x00: clear software event - -* watchdog_control - READING & 0x80 = 0x80: power off on watchdog event while thermal event - READING & 0x80 = 0x00: watchdog power off disabled (just system reset enabled) - - READING & 0x40 = 0x40: watchdog timebase 60 seconds (see also wdog:1) - READING & 0x40 = 0x00: watchdog timebase 2 seconds - - READING & 0x10 = 0x10: watchdog enabled - READING & 0x10 = 0x00: watchdog disabled - - WRITING & 0x80 = 0x80: enable "power off on watchdog event while thermal event" - WRITING & 0x80 = 0x00: disable "power off on watchdog event while thermal event" - - WRITING & 0x40 = 0x40: set watchdog timebase to 60 seconds - WRITING & 0x40 = 0x00: set watchdog timebase to 2 seconds - - WRITING & 0x20 = 0x20: disable watchdog - - WRITING & 0x10 = 0x10: enable watchdog / restart watchdog time - -* watchdog_state - READING & 0x02 = 0x02: watchdog system reset occurred - READING & 0x02 = 0x00: no watchdog system reset occurred - - WRITING & 0x02 = 0x02: clear watchdog event - -* watchdog_preset - READING & 0xff = 0x??: configured watch dog time in units (see wdog:3 0x40) - - WRITING & 0xff = 0x??: configure watch dog time in units - -* in* (0: +5V, 1: +12V, 2: onboard 3V battery) - READING: actual voltage value - -* temp*_status (1: CPU sensor, 2: onboard sensor, 3: auxiliary sensor) - READING & 0x02 = 0x02: thermal event (overtemperature) - READING & 0x02 = 0x00: no thermal event - - READING & 0x01 = 0x01: sensor is working - READING & 0x01 = 0x00: sensor is faulty - - WRITING & 0x02 = 0x02: clear thermal event - -* temp*_input (1: CPU sensor, 2: onboard sensor, 3: auxiliary sensor) - READING: actual temperature value - -* fan*_status (1: power supply fan, 2: CPU fan, 3: auxiliary fan) - READING & 0x04 = 0x04: fan event (fan fault) - READING & 0x04 = 0x00: no fan event - - WRITING & 0x04 = 0x04: clear fan event - -* fan*_div (1: power supply fan, 2: CPU fan, 3: auxiliary fan) - Divisors 2,4 and 8 are supported, both for reading and writing - -* fan*_pwm (1: power supply fan, 2: CPU fan, 3: auxiliary fan) - READING & 0xff = 0x00: fan may be switched off - READING & 0xff = 0x01: fan must run at least at minimum speed (supply: 6V) - READING & 0xff = 0xff: fan must run at maximum speed (supply: 12V) - READING & 0xff = 0x??: fan must run at least at given speed (supply: 6V..12V) - - WRITING & 0xff = 0x00: fan may be switched off - WRITING & 0xff = 0x01: fan must run at least at minimum speed (supply: 6V) - WRITING & 0xff = 0xff: fan must run at maximum speed (supply: 12V) - WRITING & 0xff = 0x??: fan must run at least at given speed (supply: 6V..12V) - -* fan*_input (1: power supply fan, 2: CPU fan, 3: auxiliary fan) - READING: actual RPM value - - -Limitations ------------ - -* Measuring fan speed -It seems that the chip counts "ripples" (typical fans produce 2 ripples per -rotation while VERAX fans produce 18) in a 9-bit register. This register is -read out every second, then the ripple prescaler (2, 4 or 8) is applied and -the result is stored in the 8 bit output register. Due to the limitation of -the counting register to 9 bits, it is impossible to measure a VERAX fan -properly (even with a prescaler of 8). At its maximum speed of 3500 RPM the -fan produces 1080 ripples per second which causes the counting register to -overflow twice, leading to only 186 RPM. - -* Measuring input voltages -in2 ("battery") reports the voltage of the onboard lithium battery and not -+3.3V from the power supply. - -* Undocumented features -Fujitsu-Siemens Computers has not documented all features of the chip so -far. Their software, System Guard, shows that there are a still some -features which cannot be controlled by this implementation. diff --git a/Documentation/hwmon/g760a b/Documentation/hwmon/g760a new file mode 100644 index 00000000000..cfc89453706 --- /dev/null +++ b/Documentation/hwmon/g760a @@ -0,0 +1,36 @@ +Kernel driver g760a +=================== + +Supported chips: + * Global Mixed-mode Technology Inc. G760A + Prefix: 'g760a' + Datasheet: Publicly available at the GMT website + http://www.gmt.com.tw/product/datasheet/EDS-760A.pdf + +Author: Herbert Valerio Riedel <hvr@gnu.org> + +Description +----------- + +The GMT G760A Fan Speed PWM Controller is connected directly to a fan +and performs closed-loop control of the fan speed. + +The fan speed is programmed by setting the period via 'pwm1' of two +consecutive speed pulses. The period is defined in terms of clock +cycle counts of an assumed 32kHz clock source. + +Setting a period of 0 stops the fan; setting the period to 255 sets +fan to maximum speed. + +The measured fan rotation speed returned via 'fan1_input' is derived +from the measured speed pulse period by assuming again a 32kHz clock +source and a 2 pulse-per-revolution fan. + +The 'alarms' file provides access to the two alarm bits provided by +the G760A chip's status register: Bit 0 is set when the actual fan +speed differs more than 20% with respect to the programmed fan speed; +bit 1 is set when fan speed is below 1920 RPM. + +The g760a driver will not update its values more frequently than every +other second; reading them more often will do no harm, but will return +'old' values. diff --git a/Documentation/hwmon/g762 b/Documentation/hwmon/g762 new file mode 100644 index 00000000000..923db9c5b5b --- /dev/null +++ b/Documentation/hwmon/g762 @@ -0,0 +1,65 @@ +Kernel driver g762 +================== + +The GMT G762 Fan Speed PWM Controller is connected directly to a fan +and performs closed-loop or open-loop control of the fan speed. Two +modes - PWM or DC - are supported by the device. + +For additional information, a detailed datasheet is available at +http://natisbad.org/NAS/ref/GMT_EDS-762_763-080710-0.2.pdf. sysfs +bindings are described in Documentation/hwmon/sysfs-interface. + +The following entries are available to the user in a subdirectory of +/sys/bus/i2c/drivers/g762/ to control the operation of the device. +This can be done manually using the following entries but is usually +done via a userland daemon like fancontrol. + +Note that those entries do not provide ways to setup the specific +hardware characteristics of the system (reference clock, pulses per +fan revolution, ...); Those can be modified via devicetree bindings +documented in Documentation/devicetree/bindings/hwmon/g762.txt or +using a specific platform_data structure in board initialization +file (see include/linux/platform_data/g762.h). + + fan1_target: set desired fan speed. This only makes sense in closed-loop + fan speed control (i.e. when pwm1_enable is set to 2). + + fan1_input: provide current fan rotation value in RPM as reported by + the fan to the device. + + fan1_div: fan clock divisor. Supported value are 1, 2, 4 and 8. + + fan1_pulses: number of pulses per fan revolution. Supported values + are 2 and 4. + + fan1_fault: reports fan failure, i.e. no transition on fan gear pin for + about 0.7s (if the fan is not voluntarily set off). + + fan1_alarm: in closed-loop control mode, if fan RPM value is 25% out + of the programmed value for over 6 seconds 'fan1_alarm' is + set to 1. + + pwm1_enable: set current fan speed control mode i.e. 1 for manual fan + speed control (open-loop) via pwm1 described below, 2 for + automatic fan speed control (closed-loop) via fan1_target + above. + + pwm1_mode: set or get fan driving mode: 1 for PWM mode, 0 for DC mode. + + pwm1: get or set PWM fan control value in open-loop mode. This is an + integer value between 0 and 255. 0 stops the fan, 255 makes + it run at full speed. + +Both in PWM mode ('pwm1_mode' set to 1) and DC mode ('pwm1_mode' set to 0), +when current fan speed control mode is open-loop ('pwm1_enable' set to 1), +the fan speed is programmed by setting a value between 0 and 255 via 'pwm1' +entry (0 stops the fan, 255 makes it run at full speed). In closed-loop mode +('pwm1_enable' set to 2), the expected rotation speed in RPM can be passed to +the chip via 'fan1_target'. In closed-loop mode, the target speed is compared +with current speed (available via 'fan1_input') by the device and a feedback +is performed to match that target value. The fan speed value is computed +based on the parameters associated with the physical characteristics of the +system: a reference clock source frequency, a number of pulses per fan +revolution, etc. + +Note that the driver will update its values at most once per second. diff --git a/Documentation/hwmon/gl518sm b/Documentation/hwmon/gl518sm index ce0881883bc..494bb55b6e7 100644 --- a/Documentation/hwmon/gl518sm +++ b/Documentation/hwmon/gl518sm @@ -5,17 +5,16 @@ Supported chips: * Genesys Logic GL518SM release 0x00 Prefix: 'gl518sm' Addresses scanned: I2C 0x2c and 0x2d - Datasheet: http://www.genesyslogic.com/pdf * Genesys Logic GL518SM release 0x80 Prefix: 'gl518sm' Addresses scanned: I2C 0x2c and 0x2d - Datasheet: http://www.genesyslogic.com/pdf + Datasheet: http://www.genesyslogic.com/ Authors: Frodo Looijaard <frodol@dds.nl>, - Kyösti Mälkki <kmalkki@cc.hut.fi> + Kyösti Mälkki <kmalkki@cc.hut.fi> Hong-Gunn Chew <hglinux@gunnet.org> - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Description ----------- diff --git a/Documentation/hwmon/hih6130 b/Documentation/hwmon/hih6130 new file mode 100644 index 00000000000..73dae918ea7 --- /dev/null +++ b/Documentation/hwmon/hih6130 @@ -0,0 +1,37 @@ +Kernel driver hih6130 +===================== + +Supported chips: + * Honeywell HIH-6130 / HIH-6131 + Prefix: 'hih6130' + Addresses scanned: none + Datasheet: Publicly available at the Honeywell website + http://sensing.honeywell.com/index.php?ci_id=3106&la_id=1&defId=44872 + +Author: + Iain Paton <ipaton0@gmail.com> + +Description +----------- + +The HIH-6130 & HIH-6131 are humidity and temperature sensors in a SO8 package. +The difference between the two devices is that the HIH-6131 has a condensation +filter. + +The devices communicate with the I2C protocol. All sensors are set to the same +I2C address 0x27 by default, so an entry with I2C_BOARD_INFO("hih6130", 0x27) +can be used in the board setup code. + +Please see Documentation/i2c/instantiating-devices for details on how to +instantiate I2C devices. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input + +Notes +----- + +Command mode and alarms are not currently supported. diff --git a/Documentation/hwmon/htu21 b/Documentation/hwmon/htu21 new file mode 100644 index 00000000000..f39a215fb6a --- /dev/null +++ b/Documentation/hwmon/htu21 @@ -0,0 +1,46 @@ +Kernel driver htu21 +=================== + +Supported chips: + * Measurement Specialties HTU21D + Prefix: 'htu21' + Addresses scanned: none + Datasheet: Publicly available at the Measurement Specialties website + http://www.meas-spec.com/downloads/HTU21D.pdf + + +Author: + William Markezana <william.markezana@meas-spec.com> + +Description +----------- + +The HTU21D is a humidity and temperature sensor in a DFN package of +only 3 x 3 mm footprint and 0.9 mm height. + +The devices communicate with the I2C protocol. All sensors are set to the +same I2C address 0x40, so an entry with I2C_BOARD_INFO("htu21", 0x40) can +be used in the board setup code. + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices +for details. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input + +Notes +----- + +The driver uses the default resolution settings of 12 bit for humidity and 14 +bit for temperature, which results in typical measurement times of 11 ms for +humidity and 44 ms for temperature. To keep self heating below 0.1 degree +Celsius, the device should not be active for more than 10% of the time. For +this reason, the driver performs no more than two measurements per second and +reports cached information if polled more frequently. + +Different resolutions, the on-chip heater, using the CRC checksum and reading +the serial number are not supported yet. diff --git a/Documentation/hwmon/hwmon-kernel-api.txt b/Documentation/hwmon/hwmon-kernel-api.txt new file mode 100644 index 00000000000..2ecdbfc85ec --- /dev/null +++ b/Documentation/hwmon/hwmon-kernel-api.txt @@ -0,0 +1,107 @@ +The Linux Hardware Monitoring kernel API. +========================================= + +Guenter Roeck + +Introduction +------------ + +This document describes the API that can be used by hardware monitoring +drivers that want to use the hardware monitoring framework. + +This document does not describe what a hardware monitoring (hwmon) Driver or +Device is. It also does not describe the API which can be used by user space +to communicate with a hardware monitoring device. If you want to know this +then please read the following file: Documentation/hwmon/sysfs-interface. + +For additional guidelines on how to write and improve hwmon drivers, please +also read Documentation/hwmon/submitting-patches. + +The API +------- +Each hardware monitoring driver must #include <linux/hwmon.h> and, in most +cases, <linux/hwmon-sysfs.h>. linux/hwmon.h declares the following +register/unregister functions: + +struct device *hwmon_device_register(struct device *dev); +struct device * +hwmon_device_register_with_groups(struct device *dev, const char *name, + void *drvdata, + const struct attribute_group **groups); + +struct device * +devm_hwmon_device_register_with_groups(struct device *dev, + const char *name, void *drvdata, + const struct attribute_group **groups); + +void hwmon_device_unregister(struct device *dev); +void devm_hwmon_device_unregister(struct device *dev); + +hwmon_device_register registers a hardware monitoring device. The parameter +of this function is a pointer to the parent device. +This function returns a pointer to the newly created hardware monitoring device +or PTR_ERR for failure. If this registration function is used, hardware +monitoring sysfs attributes are expected to have been created and attached to +the parent device prior to calling hwmon_device_register. A name attribute must +have been created by the caller. + +hwmon_device_register_with_groups is similar to hwmon_device_register. However, +it has additional parameters. The name parameter is a pointer to the hwmon +device name. The registration function wil create a name sysfs attribute +pointing to this name. The drvdata parameter is the pointer to the local +driver data. hwmon_device_register_with_groups will attach this pointer +to the newly allocated hwmon device. The pointer can be retrieved by the driver +using dev_get_drvdata() on the hwmon device pointer. The groups parameter is +a pointer to a list of sysfs attribute groups. The list must be NULL terminated. +hwmon_device_register_with_groups creates the hwmon device with name attribute +as well as all sysfs attributes attached to the hwmon device. + +devm_hwmon_device_register_with_groups is similar to +hwmon_device_register_with_groups. However, it is device managed, meaning the +hwmon device does not have to be removed explicitly by the removal function. + +hwmon_device_unregister deregisters a registered hardware monitoring device. +The parameter of this function is the pointer to the registered hardware +monitoring device structure. This function must be called from the driver +remove function if the hardware monitoring device was registered with +hwmon_device_register or with hwmon_device_register_with_groups. + +devm_hwmon_device_unregister does not normally have to be called. It is only +needed for error handling, and only needed if the driver probe fails after +the call to devm_hwmon_device_register_with_groups. + +The header file linux/hwmon-sysfs.h provides a number of useful macros to +declare and use hardware monitoring sysfs attributes. + +In many cases, you can use the exsting define DEVICE_ATTR to declare such +attributes. This is feasible if an attribute has no additional context. However, +in many cases there will be additional information such as a sensor index which +will need to be passed to the sysfs attribute handling function. + +SENSOR_DEVICE_ATTR and SENSOR_DEVICE_ATTR_2 can be used to define attributes +which need such additional context information. SENSOR_DEVICE_ATTR requires +one additional argument, SENSOR_DEVICE_ATTR_2 requires two. + +SENSOR_DEVICE_ATTR defines a struct sensor_device_attribute variable. +This structure has the following fields. + +struct sensor_device_attribute { + struct device_attribute dev_attr; + int index; +}; + +You can use to_sensor_dev_attr to get the pointer to this structure from the +attribute read or write function. Its parameter is the device to which the +attribute is attached. + +SENSOR_DEVICE_ATTR_2 defines a struct sensor_device_attribute_2 variable, +which is defined as follows. + +struct sensor_device_attribute_2 { + struct device_attribute dev_attr; + u8 index; + u8 nr; +}; + +Use to_sensor_dev_attr_2 to get the pointer to this structure. Its parameter +is the device to which the attribute is attached. diff --git a/Documentation/hwmon/ibmaem b/Documentation/hwmon/ibmaem new file mode 100644 index 00000000000..1e0d59e000b --- /dev/null +++ b/Documentation/hwmon/ibmaem @@ -0,0 +1,38 @@ +Kernel driver ibmaem +====================== + +This driver talks to the IBM Systems Director Active Energy Manager, known +henceforth as AEM. + +Supported systems: + * Any recent IBM System X server with AEM support. + This includes the x3350, x3550, x3650, x3655, x3755, x3850 M2, + x3950 M2, and certain HC10/HS2x/LS2x/QS2x blades. The IPMI host interface + driver ("ipmi-si") needs to be loaded for this driver to do anything. + Prefix: 'ibmaem' + Datasheet: Not available + +Author: Darrick J. Wong + +Description +----------- + +This driver implements sensor reading support for the energy and power meters +available on various IBM System X hardware through the BMC. All sensor banks +will be exported as platform devices; this driver can talk to both v1 and v2 +interfaces. This driver is completely separate from the older ibmpex driver. + +The v1 AEM interface has a simple set of features to monitor energy use. There +is a register that displays an estimate of raw energy consumption since the +last BMC reset, and a power sensor that returns average power use over a +configurable interval. + +The v2 AEM interface is a bit more sophisticated, being able to present a wider +range of energy and power use registers, the power cap as set by the AEM +software, and temperature sensors. + +Special Features +---------------- + +The "power_cap" value displays the current system power cap, as set by the AEM +software. Setting the power cap from the host is not currently supported. diff --git a/Documentation/hwmon/ina209 b/Documentation/hwmon/ina209 new file mode 100644 index 00000000000..672501de450 --- /dev/null +++ b/Documentation/hwmon/ina209 @@ -0,0 +1,93 @@ +Kernel driver ina209 +===================== + +Supported chips: + * Burr-Brown / Texas Instruments INA209 + Prefix: 'ina209' + Addresses scanned: - + Datasheet: + http://www.ti.com/lit/gpn/ina209 + +Author: Paul Hays <Paul.Hays@cattail.ca> +Author: Ira W. Snyder <iws@ovro.caltech.edu> +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +The TI / Burr-Brown INA209 monitors voltage, current, and power on the high side +of a D.C. power supply. It can perform measurements and calculations in the +background to supply readings at any time. It includes a programmable +calibration multiplier to scale the displayed current and power values. + + +Sysfs entries +------------- + +The INA209 chip is highly configurable both via hardwiring and via +the I2C bus. See the datasheet for details. + +This tries to expose most monitoring features of the hardware via +sysfs. It does not support every feature of this chip. + + +in0_input shunt voltage (mV) +in0_input_highest shunt voltage historical maximum reading (mV) +in0_input_lowest shunt voltage historical minimum reading (mV) +in0_reset_history reset shunt voltage history +in0_max shunt voltage max alarm limit (mV) +in0_min shunt voltage min alarm limit (mV) +in0_crit_max shunt voltage crit max alarm limit (mV) +in0_crit_min shunt voltage crit min alarm limit (mV) +in0_max_alarm shunt voltage max alarm limit exceeded +in0_min_alarm shunt voltage min alarm limit exceeded +in0_crit_max_alarm shunt voltage crit max alarm limit exceeded +in0_crit_min_alarm shunt voltage crit min alarm limit exceeded + +in1_input bus voltage (mV) +in1_input_highest bus voltage historical maximum reading (mV) +in1_input_lowest bus voltage historical minimum reading (mV) +in1_reset_history reset bus voltage history +in1_max bus voltage max alarm limit (mV) +in1_min bus voltage min alarm limit (mV) +in1_crit_max bus voltage crit max alarm limit (mV) +in1_crit_min bus voltage crit min alarm limit (mV) +in1_max_alarm bus voltage max alarm limit exceeded +in1_min_alarm bus voltage min alarm limit exceeded +in1_crit_max_alarm bus voltage crit max alarm limit exceeded +in1_crit_min_alarm bus voltage crit min alarm limit exceeded + +power1_input power measurement (uW) +power1_input_highest power historical maximum reading (uW) +power1_reset_history reset power history +power1_max power max alarm limit (uW) +power1_crit power crit alarm limit (uW) +power1_max_alarm power max alarm limit exceeded +power1_crit_alarm power crit alarm limit exceeded + +curr1_input current measurement (mA) + +update_interval data conversion time; affects number of samples used + to average results for shunt and bus voltages. + +General Remarks +--------------- + +The power and current registers in this chip require that the calibration +register is programmed correctly before they are used. Normally this is expected +to be done in the BIOS. In the absence of BIOS programming, the shunt resistor +voltage can be provided using platform data. The driver uses platform data from +the ina2xx driver for this purpose. If calibration register data is not provided +via platform data, the driver checks if the calibration register has been +programmed (ie has a value not equal to zero). If so, this value is retained. +Otherwise, a default value reflecting a shunt resistor value of 10 mOhm is +programmed into the calibration register. + + +Output Pins +----------- + +Output pin programming is a board feature which depends on the BIOS. It is +outside the scope of a hardware monitoring driver to enable or disable output +pins. diff --git a/Documentation/hwmon/ina2xx b/Documentation/hwmon/ina2xx new file mode 100644 index 00000000000..4223c2d3b50 --- /dev/null +++ b/Documentation/hwmon/ina2xx @@ -0,0 +1,49 @@ +Kernel driver ina2xx +==================== + +Supported chips: + * Texas Instruments INA219 + Prefix: 'ina219' + Addresses: I2C 0x40 - 0x4f + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/ + + * Texas Instruments INA220 + Prefix: 'ina220' + Addresses: I2C 0x40 - 0x4f + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/ + + * Texas Instruments INA226 + Prefix: 'ina226' + Addresses: I2C 0x40 - 0x4f + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/ + + * Texas Instruments INA230 + Prefix: 'ina230' + Addresses: I2C 0x40 - 0x4f + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/ + +Author: Lothar Felten <l-felten@ti.com> + +Description +----------- + +The INA219 is a high-side current shunt and power monitor with an I2C +interface. The INA219 monitors both shunt drop and supply voltage, with +programmable conversion times and filtering. + +The INA220 is a high or low side current shunt and power monitor with an I2C +interface. The INA220 monitors both shunt drop and supply voltage. + +The INA226 is a current shunt and power monitor with an I2C interface. +The INA226 monitors both a shunt voltage drop and bus supply voltage. + +The INA230 is a high or low side current shunt and power monitor with an I2C +interface. The INA230 monitors both a shunt voltage drop and bus supply voltage. + +The shunt value in micro-ohms can be set via platform data or device tree. +Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings +if the device tree is used. diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87 index 7f42e441c64..fe80e9adebf 100644 --- a/Documentation/hwmon/it87 +++ b/Documentation/hwmon/it87 @@ -2,23 +2,62 @@ Kernel driver it87 ================== Supported chips: + * IT8603E/IT8623E + Prefix: 'it8603' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available * IT8705F Prefix: 'it87' Addresses scanned: from Super I/O config space (8 I/O ports) - Datasheet: Publicly available at the ITE website - http://www.ite.com.tw/ + Datasheet: Once publicly available at the ITE website, but no longer * IT8712F Prefix: 'it8712' - Addresses scanned: I2C 0x28 - 0x2f - from Super I/O config space (8 I/O ports) - Datasheet: Publicly available at the ITE website - http://www.ite.com.tw/ + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Once publicly available at the ITE website, but no longer + * IT8716F/IT8726F + Prefix: 'it8716' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Once publicly available at the ITE website, but no longer + * IT8718F + Prefix: 'it8718' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Once publicly available at the ITE website, but no longer + * IT8720F + Prefix: 'it8720' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8721F/IT8758E + Prefix: 'it8721' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8728F + Prefix: 'it8728' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8771E + Prefix: 'it8771' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8772E + Prefix: 'it8772' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8782F + Prefix: 'it8782' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8783E/F + Prefix: 'it8783' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available * SiS950 [clone of IT8705F] Prefix: 'it87' Addresses scanned: from Super I/O config space (8 I/O ports) Datasheet: No longer be available -Author: Christophe Gauthron <chrisg@0-in.com> +Authors: + Christophe Gauthron + Jean Delvare <jdelvare@suse.de> Module Parameters @@ -40,40 +79,94 @@ Module Parameters misconfigured by BIOS - PWM values would be inverted. This option tries to fix this. Please contact your BIOS manufacturer and ask him for fix. + +Hardware Interfaces +------------------- + +All the chips supported by this driver are LPC Super-I/O chips, accessed +through the LPC bus (ISA-like I/O ports). The IT8712F additionally has an +SMBus interface to the hardware monitoring functions. This driver no +longer supports this interface though, as it is slower and less reliable +than the ISA access, and was only available on a small number of +motherboard models. + + Description ----------- -This driver implements support for the IT8705F, IT8712F and SiS950 chips. - -This driver also supports IT8712F, which adds SMBus access, and a VID -input, used to report the Vcore voltage of the Pentium processor. -The IT8712F additionally features VID inputs. +This driver implements support for the IT8603E, IT8623E, IT8705F, IT8712F, +IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, IT8771E, +IT8772E, IT8782F, IT8783E/F, and SiS950 chips. These chips are 'Super I/O chips', supporting floppy disks, infrared ports, joysticks and other miscellaneous stuff. For hardware monitoring, they include an 'environment controller' with 3 temperature sensors, 3 fan -rotation speed sensors, 8 voltage sensors, and associated alarms. +rotation speed sensors, 8 voltage sensors, associated alarms, and chassis +intrusion detection. + +The IT8712F and IT8716F additionally feature VID inputs, used to report +the Vcore voltage of the processor. The early IT8712F have 5 VID pins, +the IT8716F and late IT8712F have 6. They are shared with other functions +though, so the functionality may not be available on a given system. + +The IT8718F and IT8720F also features VID inputs (up to 8 pins) but the value +is stored in the Super-I/O configuration space. Due to technical limitations, +this value can currently only be read once at initialization time, so +the driver won't notice and report changes in the VID value. The two +upper VID bits share their pins with voltage inputs (in5 and in6) so you +can't have both on a given board. + +The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E and later IT8712F revisions +have support for 2 additional fans. The additional fans are supported by the +driver. + +The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E, IT8782F, IT8783E/F, and late +IT8712F and IT8705F also have optional 16-bit tachometer counters for fans 1 to +3. This is better (no more fan clock divider mess) but not compatible with the +older chips and revisions. The 16-bit tachometer mode is enabled by the driver +when one of the above chips is detected. + +The IT8726F is just bit enhanced IT8716F with additional hardware +for AMD power sequencing. Therefore the chip will appear as IT8716F +to userspace applications. + +The IT8728F, IT8771E, and IT8772E are considered compatible with the IT8721F, +until a datasheet becomes available (hopefully.) + +The IT8603E/IT8623E is a custom design, hardware monitoring part is similar to +IT8728F. It only supports 16-bit fan mode, the full speed mode of the +fan is not supported (value 0 of pwmX_enable). Temperatures are measured in degrees Celsius. An alarm is triggered once when the Overtemperature Shutdown limit is crossed. Fan rotation speeds are reported in RPM (rotations per minute). An alarm is -triggered if the rotation speed has dropped below a programmable limit. Fan -readings can be divided by a programmable divider (1, 2, 4 or 8) to give the -readings more range or accuracy. Not all RPM values can accurately be -represented, so some rounding is done. With a divider of 2, the lowest -representable value is around 2600 RPM. +triggered if the rotation speed has dropped below a programmable limit. When +16-bit tachometer counters aren't used, fan readings can be divided by +a programmable divider (1, 2, 4 or 8) to give the readings more range or +accuracy. With a divider of 2, the lowest representable value is around +2600 RPM. Not all RPM values can accurately be represented, so some rounding +is done. Voltage sensors (also known as IN sensors) report their values in volts. An alarm is triggered if the voltage has crossed a programmable minimum or maximum limit. Note that minimum in this case always means 'closest to zero'; this is important for negative voltage measurements. All voltage inputs can measure voltages between 0 and 4.08 volts, with a resolution of -0.016 volt. The battery voltage in8 does not have limit registers. +0.016 volt (except IT8603E, IT8721F/IT8758E and IT8728F: 0.012 volt.) The +battery voltage in8 does not have limit registers. -The VID lines (IT8712F only) encode the core voltage value: the voltage -level your processor should work with. This is hardcoded by the mainboard -and/or processor itself. It is a value in volts. +On the IT8603E, IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs +are internal and scaled inside the chip: +* in3 (optional) +* in7 (optional for IT8782F and IT8783E/F) +* in8 (always) +* in9 (relevant for IT8603E only) +The driver handles this transparently so user-space doesn't have to care. + +The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value: +the voltage level your processor should work with. This is hardcoded by +the mainboard and/or processor itself. It is a value in volts. If an alarm triggers, it will remain triggered until the hardware register is read at least once. This means that the cause for the alarm may already @@ -82,15 +175,66 @@ registers are read whenever any data is read (unless it is less than 1.5 seconds since the last update). This means that you can easily miss once-only alarms. +Out-of-limit readings can also result in beeping, if the chip is properly +wired and configured. Beeping can be enabled or disabled per sensor type +(temperatures, voltages and fans.) + The IT87xx only updates its values each 1.5 seconds; reading it more often will do no harm, but will return 'old' values. -To change sensor N to a thermistor, 'echo 2 > tempN_type' where N is 1, 2, +To change sensor N to a thermistor, 'echo 4 > tempN_type' where N is 1, 2, or 3. To change sensor N to a thermal diode, 'echo 3 > tempN_type'. Give 0 for unused sensor. Any other value is invalid. To configure this at -startup, consult lm_sensors's /etc/sensors.conf. (2 = thermistor; +startup, consult lm_sensors's /etc/sensors.conf. (4 = thermistor; 3 = thermal diode) + +Fan speed control +----------------- + The fan speed control features are limited to manual PWM mode. Automatic -"Smart Guardian" mode control handling is not implemented. However -if you want to go for "manual mode" just write 1 to pwmN_enable. +"Smart Guardian" mode control handling is only implemented for older chips +(see below.) However if you want to go for "manual mode" just write 1 to +pwmN_enable. + +If you are only able to control the fan speed with very small PWM values, +try lowering the PWM base frequency (pwm1_freq). Depending on the fan, +it may give you a somewhat greater control range. The same frequency is +used to drive all fan outputs, which is why pwm2_freq and pwm3_freq are +read-only. + + +Automatic fan speed control (old interface) +------------------------------------------- + +The driver supports the old interface to automatic fan speed control +which is implemented by IT8705F chips up to revision F and IT8712F +chips up to revision G. + +This interface implements 4 temperature vs. PWM output trip points. +The PWM output of trip point 4 is always the maximum value (fan running +at full speed) while the PWM output of the other 3 trip points can be +freely chosen. The temperature of all 4 trip points can be freely chosen. +Additionally, trip point 1 has an hysteresis temperature attached, to +prevent fast switching between fan on and off. + +The chip automatically computes the PWM output value based on the input +temperature, based on this simple rule: if the temperature value is +between trip point N and trip point N+1 then the PWM output value is +the one of trip point N. The automatic control mode is less flexible +than the manual control mode, but it reacts faster, is more robust and +doesn't use CPU cycles. + +Trip points must be set properly before switching to automatic fan speed +control mode. The driver will perform basic integrity checks before +actually switching to automatic control mode. + + +Temperature offset attributes +----------------------------- + +The driver supports temp[1-3]_offset sysfs attributes to adjust the reported +temperature for thermal diodes or diode-connected thermal transistors. +If a temperature sensor is configured for thermistors, the attribute values +are ignored. If the thermal sensor type is Intel PECI, the temperature offset +must be programmed to the critical CPU temperature. diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 new file mode 100644 index 00000000000..f3893f7440d --- /dev/null +++ b/Documentation/hwmon/jc42 @@ -0,0 +1,104 @@ +Kernel driver jc42 +================== + +Supported chips: + * Analog Devices ADT7408 + Datasheets: + http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf + * Atmel AT30TS00, AT30TS002A/B, AT30TSE004A + Datasheets: + http://www.atmel.com/Images/doc8585.pdf + http://www.atmel.com/Images/doc8711.pdf + http://www.atmel.com/Images/Atmel-8852-SEEPROM-AT30TSE002A-Datasheet.pdf + http://www.atmel.com/Images/Atmel-8868-DTS-AT30TSE004A-Datasheet.pdf + * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2 + Datasheets: + http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf + http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf + * Maxim MAX6604 + Datasheets: + http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf + * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP98244, MCP9843 + Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/22327A.pdf + * NXP Semiconductors SE97, SE97B, SE98, SE98A + Datasheets: + http://www.nxp.com/documents/data_sheet/SE97.pdf + http://www.nxp.com/documents/data_sheet/SE97B.pdf + http://www.nxp.com/documents/data_sheet/SE98.pdf + http://www.nxp.com/documents/data_sheet/SE98A.pdf + * ON Semiconductor CAT34TS02, CAT6095 + Datasheet: + http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF + http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF + * ST Microelectronics STTS424, STTS424E02, STTS2002, STTS2004, STTS3000 + Datasheets: + http://www.st.com/web/en/resource/technical/document/datasheet/CD00157556.pdf + http://www.st.com/web/en/resource/technical/document/datasheet/CD00157558.pdf + http://www.st.com/web/en/resource/technical/document/datasheet/CD00266638.pdf + http://www.st.com/web/en/resource/technical/document/datasheet/CD00225278.pdf + http://www.st.com/web/en/resource/technical/document/datasheet/DM00076709.pdf + * JEDEC JC 42.4 compliant temperature sensor chips + Datasheet: + http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf + + Common for all chips: + Prefix: 'jc42' + Addresses scanned: I2C 0x18 - 0x1f + +Author: + Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver implements support for JEDEC JC 42.4 compliant temperature sensors, +which are used on many DDR3 memory modules for mobile devices and servers. Some +systems use the sensor to prevent memory overheating by automatically throttling +the memory controller. + +The driver auto-detects the chips listed above, but can be manually instantiated +to support other JC 42.4 compliant chips. + +Example: the following will load the driver for a generic JC 42.4 compliant +temperature sensor at address 0x18 on I2C bus #1: + +# modprobe jc42 +# echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device + +A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum, +and critical temperature can be configured. There are alarms for high, low, +and critical thresholds. + +There is also an hysteresis to control the thresholds for resetting alarms. +Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5, +3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those +limits. The chip supports only a single register to configure the hysteresis, +which applies to all limits. This register can be written by writing into +temp1_crit_hyst. Other hysteresis attributes are read-only. + +If the BIOS has configured the sensor for automatic temperature management, it +is likely that it has locked the registers, i.e., that the temperature limits +cannot be changed. + +Sysfs entries +------------- + +temp1_input Temperature (RO) +temp1_min Minimum temperature (RO or RW) +temp1_max Maximum temperature (RO or RW) +temp1_crit Critical high temperature (RO or RW) + +temp1_crit_hyst Critical hysteresis temperature (RO or RW) +temp1_max_hyst Maximum hysteresis temperature (RO) + +temp1_min_alarm Temperature low alarm +temp1_max_alarm Temperature high alarm +temp1_crit_alarm Temperature critical alarm diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp new file mode 100644 index 00000000000..ee6d30ec152 --- /dev/null +++ b/Documentation/hwmon/k10temp @@ -0,0 +1,77 @@ +Kernel driver k10temp +===================== + +Supported chips: +* AMD Family 10h processors: + Socket F: Quad-Core/Six-Core/Embedded Opteron (but see below) + Socket AM2+: Quad-Core Opteron, Phenom (II) X3/X4, Athlon X2 (but see below) + Socket AM3: Quad-Core Opteron, Athlon/Phenom II X2/X3/X4, Sempron II + Socket S1G3: Athlon II, Sempron, Turion II +* AMD Family 11h processors: + Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra) +* AMD Family 12h processors: "Llano" (E2/A4/A6/A8-Series) +* AMD Family 14h processors: "Brazos" (C/E/G/Z-Series) +* AMD Family 15h processors: "Bulldozer" (FX-Series), "Trinity", "Kaveri" +* AMD Family 16h processors: "Kabini", "Mullins" + + Prefix: 'k10temp' + Addresses scanned: PCI space + Datasheets: + BIOS and Kernel Developer's Guide (BKDG) For AMD Family 10h Processors: + http://support.amd.com/us/Processor_TechDocs/31116.pdf + BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors: + http://support.amd.com/us/Processor_TechDocs/41256.pdf + BIOS and Kernel Developer's Guide (BKDG) for AMD Family 12h Processors: + http://support.amd.com/us/Processor_TechDocs/41131.pdf + BIOS and Kernel Developer's Guide (BKDG) for AMD Family 14h Models 00h-0Fh Processors: + http://support.amd.com/us/Processor_TechDocs/43170.pdf + Revision Guide for AMD Family 10h Processors: + http://support.amd.com/us/Processor_TechDocs/41322.pdf + Revision Guide for AMD Family 11h Processors: + http://support.amd.com/us/Processor_TechDocs/41788.pdf + Revision Guide for AMD Family 12h Processors: + http://support.amd.com/us/Processor_TechDocs/44739.pdf + Revision Guide for AMD Family 14h Models 00h-0Fh Processors: + http://support.amd.com/us/Processor_TechDocs/47534.pdf + AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks: + http://support.amd.com/us/Processor_TechDocs/43373.pdf + AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet: + http://support.amd.com/us/Processor_TechDocs/43374.pdf + AMD Family 10h Desktop Processor Power and Thermal Data Sheet: + http://support.amd.com/us/Processor_TechDocs/43375.pdf + +Author: Clemens Ladisch <clemens@ladisch.de> + +Description +----------- + +This driver permits reading of the internal temperature sensor of AMD +Family 10h/11h/12h/14h/15h/16h processors. + +All these processors have a sensor, but on those for Socket F or AM2+, +the sensor may return inconsistent values (erratum 319). The driver +will refuse to load on these revisions unless you specify the "force=1" +module parameter. + +Due to technical reasons, the driver can detect only the mainboard's +socket type, not the processor's actual capabilities. Therefore, if you +are using an AM3 processor on an AM2+ mainboard, you can safely use the +"force=1" parameter. + +There is one temperature measurement value, available as temp1_input in +sysfs. It is measured in degrees Celsius with a resolution of 1/8th degree. +Please note that it is defined as a relative value; to quote the AMD manual: + + Tctl is the processor temperature control value, used by the platform to + control cooling systems. Tctl is a non-physical temperature on an + arbitrary scale measured in degrees. It does _not_ represent an actual + physical temperature like die or case temperature. Instead, it specifies + the processor temperature relative to the point at which the system must + supply the maximum cooling for the processor's specified maximum case + temperature and maximum thermal power dissipation. + +The maximum value for Tctl is available in the file temp1_max. + +If the BIOS has enabled hardware temperature control, the threshold at +which the processor will throttle itself to avoid damage is available in +temp1_crit and temp1_crit_hyst. diff --git a/Documentation/hwmon/k8temp b/Documentation/hwmon/k8temp new file mode 100644 index 00000000000..716dc24c723 --- /dev/null +++ b/Documentation/hwmon/k8temp @@ -0,0 +1,55 @@ +Kernel driver k8temp +==================== + +Supported chips: + * AMD Athlon64/FX or Opteron CPUs + Prefix: 'k8temp' + Addresses scanned: PCI space + Datasheet: http://support.amd.com/us/Processor_TechDocs/32559.pdf + +Author: Rudolf Marek +Contact: Rudolf Marek <r.marek@assembler.cz> + +Description +----------- + +This driver permits reading temperature sensor(s) embedded inside AMD K8 +family CPUs (Athlon64/FX, Opteron). Official documentation says that it works +from revision F of K8 core, but in fact it seems to be implemented for all +revisions of K8 except the first two revisions (SH-B0 and SH-B3). + +Please note that you will need at least lm-sensors 2.10.1 for proper userspace +support. + +There can be up to four temperature sensors inside single CPU. The driver +will auto-detect the sensors and will display only temperatures from +implemented sensors. + +Mapping of /sys files is as follows: + +temp1_input - temperature of Core 0 and "place" 0 +temp2_input - temperature of Core 0 and "place" 1 +temp3_input - temperature of Core 1 and "place" 0 +temp4_input - temperature of Core 1 and "place" 1 + +Temperatures are measured in degrees Celsius and measurement resolution is +1 degree C. It is expected that future CPU will have better resolution. The +temperature is updated once a second. Valid temperatures are from -49 to +206 degrees C. + +Temperature known as TCaseMax was specified for processors up to revision E. +This temperature is defined as temperature between heat-spreader and CPU +case, so the internal CPU temperature supplied by this driver can be higher. +There is no easy way how to measure the temperature which will correlate +with TCaseMax temperature. + +For newer revisions of CPU (rev F, socket AM2) there is a mathematically +computed temperature called TControl, which must be lower than TControlMax. + +The relationship is following: + +temp1_input - TjOffset*2 < TControlMax, + +TjOffset is not yet exported by the driver, TControlMax is usually +70 degrees C. The rule of the thumb -> CPU temperature should not cross +60 degrees C too much. diff --git a/Documentation/hwmon/lineage-pem b/Documentation/hwmon/lineage-pem new file mode 100644 index 00000000000..83b2ddc160c --- /dev/null +++ b/Documentation/hwmon/lineage-pem @@ -0,0 +1,77 @@ +Kernel driver lineage-pem +========================= + +Supported devices: + * Lineage Compact Power Line Power Entry Modules + Prefix: 'lineage-pem' + Addresses scanned: - + Documentation: + http://www.lineagepower.com/oem/pdf/CPLI2C.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports various Lineage Compact Power Line DC/DC and AC/DC +converters such as CP1800, CP2000AC, CP2000DC, CP2100DC, and others. + +Lineage CPL power entry modules are nominally PMBus compliant. However, most +standard PMBus commands are not supported. Specifically, all hardware monitoring +and status reporting commands are non-standard. For this reason, a standard +PMBus driver can not be used. + + +Usage Notes +----------- + +This driver does not probe for Lineage CPL devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for a Lineage PEM at address 0x40 +on I2C bus #1: +$ modprobe lineage-pem +$ echo lineage-pem 0x40 > /sys/bus/i2c/devices/i2c-1/new_device + +All Lineage CPL power entry modules have a built-in I2C bus master selector +(PCA9541). To ensure device access, this driver should only be used as client +driver to the pca9541 I2C master selector driver. + + +Sysfs entries +------------- + +All Lineage CPL devices report output voltage and device temperature as well as +alarms for output voltage, temperature, input voltage, input current, input power, +and fan status. + +Input voltage, input current, input power, and fan speed measurement is only +supported on newer devices. The driver detects if those attributes are supported, +and only creates respective sysfs entries if they are. + +in1_input Output voltage (mV) +in1_min_alarm Output undervoltage alarm +in1_max_alarm Output overvoltage alarm +in1_crit Output voltage critical alarm + +in2_input Input voltage (mV, optional) +in2_alarm Input voltage alarm + +curr1_input Input current (mA, optional) +curr1_alarm Input overcurrent alarm + +power1_input Input power (uW, optional) +power1_alarm Input power alarm + +fan1_input Fan 1 speed (rpm, optional) +fan2_input Fan 2 speed (rpm, optional) +fan3_input Fan 3 speed (rpm, optional) + +temp1_input +temp1_max +temp1_crit +temp1_alarm +temp1_crit_alarm +temp1_fault diff --git a/Documentation/hwmon/lm25066 b/Documentation/hwmon/lm25066 new file mode 100644 index 00000000000..b34c3de5c1b --- /dev/null +++ b/Documentation/hwmon/lm25066 @@ -0,0 +1,120 @@ +Kernel driver lm25066 +===================== + +Supported chips: + * TI LM25056 + Prefix: 'lm25056' + Addresses scanned: - + Datasheets: + http://www.ti.com/lit/gpn/lm25056 + http://www.ti.com/lit/gpn/lm25056a + * TI LM25063 + Prefix: 'lm25063' + Addresses scanned: - + Datasheet: + To be announced + * National Semiconductor LM25066 + Prefix: 'lm25066' + Addresses scanned: - + Datasheets: + http://www.national.com/pf/LM/LM25066.html + http://www.national.com/pf/LM/LM25066A.html + * National Semiconductor LM5064 + Prefix: 'lm5064' + Addresses scanned: - + Datasheet: + http://www.national.com/pf/LM/LM5064.html + * National Semiconductor LM5066 + Prefix: 'lm5066' + Addresses scanned: - + Datasheet: + http://www.national.com/pf/LM/LM5066.html + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for National Semiconductor / TI LM25056, +LM25063, LM25066, LM5064, and LM5066 Power Management, Monitoring, Control, and +Protection ICs. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vin" +in1_input Measured input voltage. +in1_average Average measured input voltage. +in1_min Minimum input voltage. +in1_max Maximum input voltage. +in1_crit Critical high input voltage (LM25063 only). +in1_lcrit Critical low input voltage (LM25063 only). +in1_min_alarm Input voltage low alarm. +in1_max_alarm Input voltage high alarm. +in1_lcrit_alarm Input voltage critical low alarm (LM25063 only). +in1_crit_alarm Input voltage critical high alarm. (LM25063 only). + +in2_label "vmon" +in2_input Measured voltage on VAUX pin +in2_min Minimum VAUX voltage (LM25056 only). +in2_max Maximum VAUX voltage (LM25056 only). +in2_min_alarm VAUX voltage low alarm (LM25056 only). +in2_max_alarm VAUX voltage high alarm (LM25056 only). + +in3_label "vout1" + Not supported on LM25056. +in3_input Measured output voltage. +in3_average Average measured output voltage. +in3_min Minimum output voltage. +in3_min_alarm Output voltage low alarm. +in3_highest Historical minimum output voltage (LM25063 only). +in3_lowest Historical maximum output voltage (LM25063 only). + +curr1_label "iin" +curr1_input Measured input current. +curr1_average Average measured input current. +curr1_max Maximum input current. +curr1_crit Critical input current (LM25063 only). +curr1_max_alarm Input current high alarm. +curr1_crit_alarm Input current critical high alarm (LM25063 only). + +power1_label "pin" +power1_input Measured input power. +power1_average Average measured input power. +power1_max Maximum input power limit. +power1_alarm Input power alarm +power1_input_highest Historical maximum power. +power1_reset_history Write any value to reset maximum power history. + +power2_label "pout". LM25063 only. +power2_input Measured output power. +power2_max Maximum output power limit. +power2_crit Critical output power limit. + +temp1_input Measured temperature. +temp1_max Maximum temperature. +temp1_crit Critical high temperature. +temp1_max_alarm Chip temperature high alarm. +temp1_crit_alarm Chip temperature critical high alarm. diff --git a/Documentation/hwmon/lm63 b/Documentation/hwmon/lm63 index 31660bf9797..4a00461512a 100644 --- a/Documentation/hwmon/lm63 +++ b/Documentation/hwmon/lm63 @@ -7,8 +7,18 @@ Supported chips: Addresses scanned: I2C 0x4c Datasheet: Publicly available at the National Semiconductor website http://www.national.com/pf/LM/LM63.html + * National Semiconductor LM64 + Prefix: 'lm64' + Addresses scanned: I2C 0x18 and 0x4e + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/pf/LM/LM64.html + * National Semiconductor LM96163 + Prefix: 'lm96163' + Addresses scanned: I2C 0x4c + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/pf/LM/LM96163.html -Author: Jean Delvare <khali@linux-fr.org> +Author: Jean Delvare <jdelvare@suse.de> Thanks go to Tyan and especially Alex Buckingham for setting up a remote access to their S4882 test platform for this driver. @@ -44,14 +54,24 @@ value for measuring the speed of the fan. It can measure fan speeds down to Note that the pin used for fan monitoring is shared with an alert out function. Depending on how the board designer wanted to use the chip, fan speed monitoring will or will not be possible. The proper chip configuration -is left to the BIOS, and the driver will blindly trust it. +is left to the BIOS, and the driver will blindly trust it. Only the original +LM63 suffers from this limitation, the LM64 and LM96163 have separate pins +for fan monitoring and alert out. On the LM64, monitoring is always enabled; +on the LM96163 it can be disabled. A PWM output can be used to control the speed of the fan. The LM63 has two PWM modes: manual and automatic. Automatic mode is not fully implemented yet (you cannot define your custom PWM/temperature curve), and mode change isn't supported either. -The lm63 driver will not update its values more frequently than every -second; reading them more often will do no harm, but will return 'old' -values. +The lm63 driver will not update its values more frequently than configured with +the update_interval sysfs attribute; reading them more often will do no harm, +but will return 'old' values. Values in the automatic fan control lookup table +(attributes pwm1_auto_*) have their own independent lifetime of 5 seconds. + +The LM64 is effectively an LM63 with GPIO lines. The driver does not +support these GPIO lines at present. +The LM96163 is an enhanced version of LM63 with improved temperature accuracy +and better PWM resolution. For LM96163, the external temperature sensor type is +configurable as CPU embedded diode(1) or 3904 transistor(2). diff --git a/Documentation/hwmon/lm70 b/Documentation/hwmon/lm70 new file mode 100644 index 00000000000..1bb2db44067 --- /dev/null +++ b/Documentation/hwmon/lm70 @@ -0,0 +1,47 @@ +Kernel driver lm70 +================== + +Supported chips: + * National Semiconductor LM70 + Datasheet: http://www.national.com/pf/LM/LM70.html + * Texas Instruments TMP121/TMP123 + Information: http://focus.ti.com/docs/prod/folders/print/tmp121.html + * National Semiconductor LM71 + Datasheet: http://www.ti.com/product/LM71 + * National Semiconductor LM74 + Datasheet: http://www.ti.com/product/LM74 + +Author: + Kaiwan N Billimoria <kaiwan@designergraphix.com> + +Description +----------- + +This driver implements support for the National Semiconductor LM70 +temperature sensor. + +The LM70 temperature sensor chip supports a single temperature sensor. +It communicates with a host processor (or microcontroller) via an +SPI/Microwire Bus interface. + +Communication with the LM70 is simple: when the temperature is to be sensed, +the driver accesses the LM70 using SPI communication: 16 SCLK cycles +comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's +complement digital temperature (sent via the SIO line), is available in the +driver for interpretation. This driver makes use of the kernel's in-core +SPI support. + +As a real (in-tree) example of this "SPI protocol driver" interfacing +with a "SPI master controller driver", see drivers/spi/spi_lm70llp.c +and its associated documentation. + +The LM74 and TMP121/TMP123 are very similar; main difference is 13-bit +temperature data (0.0625 degrees celsius resolution). + +The LM71 is also very similar; main difference is 14-bit temperature +data (0.03125 degrees celsius resolution). + +Thanks to +--------- +Jean Delvare <jdelvare@suse.de> for mentoring the hwmon-side driver +development. diff --git a/Documentation/hwmon/lm73 b/Documentation/hwmon/lm73 new file mode 100644 index 00000000000..8af059dcb64 --- /dev/null +++ b/Documentation/hwmon/lm73 @@ -0,0 +1,90 @@ +Kernel driver lm73 +================== + +Supported chips: + * Texas Instruments LM73 + Prefix: 'lm73' + Addresses scanned: I2C 0x48, 0x49, 0x4a, 0x4c, 0x4d, and 0x4e + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/product/lm73 + +Author: Guillaume Ligneul <guillaume.ligneul@gmail.com> +Documentation: Chris Verges <kg4ysn@gmail.com> + + +Description +----------- + +The LM73 is a digital temperature sensor. All temperature values are +given in degrees Celsius. + +Measurement Resolution Support +------------------------------ + +The LM73 supports four resolutions, defined in terms of degrees C per +LSB: 0.25, 0.125, 0.0625, and 0.3125. Changing the resolution mode +affects the conversion time of the LM73's analog-to-digital converter. +From userspace, the desired resolution can be specified as a function of +conversion time via the 'update_interval' sysfs attribute for the +device. This attribute will normalize ranges of input values to the +maximum times defined for the resolution in the datasheet. + + Resolution Conv. Time Input Range + (C/LSB) (msec) (msec) + -------------------------------------- + 0.25 14 0..14 + 0.125 28 15..28 + 0.0625 56 29..56 + 0.03125 112 57..infinity + -------------------------------------- + +The following examples show how the 'update_interval' attribute can be +used to change the conversion time: + + $ echo 0 > update_interval + $ cat update_interval + 14 + $ cat temp1_input + 24250 + + $ echo 22 > update_interval + $ cat update_interval + 28 + $ cat temp1_input + 24125 + + $ echo 56 > update_interval + $ cat update_interval + 56 + $ cat temp1_input + 24062 + + $ echo 85 > update_interval + $ cat update_interval + 112 + $ cat temp1_input + 24031 + +As shown here, the lm73 driver automatically adjusts any user input for +'update_interval' via a step function. Reading back the +'update_interval' value after a write operation will confirm the +conversion time actively in use. + +Mathematically, the resolution can be derived from the conversion time +via the following function: + + g(x) = 0.250 * [log(x/14) / log(2)] + +where 'x' is the output from 'update_interval' and 'g(x)' is the +resolution in degrees C per LSB. + +Alarm Support +------------- + +The LM73 features a simple over-temperature alarm mechanism. This +feature is exposed via the sysfs attributes. + +The attributes 'temp1_max_alarm' and 'temp1_min_alarm' are flags +provided by the LM73 that indicate whether the measured temperature has +passed the 'temp1_max' and 'temp1_min' thresholds, respectively. These +values _must_ be read to clear the registers on the LM73. diff --git a/Documentation/hwmon/lm75 b/Documentation/hwmon/lm75 index 8e6356fe05d..2560a9c6d44 100644 --- a/Documentation/hwmon/lm75 +++ b/Documentation/hwmon/lm75 @@ -7,26 +7,51 @@ Supported chips: Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ - * Dallas Semiconductor DS75 - Prefix: 'lm75' - Addresses scanned: I2C 0x48 - 0x4f - Datasheet: Publicly available at the Dallas Semiconductor website - http://www.maxim-ic.com/ - * Dallas Semiconductor DS1775 - Prefix: 'lm75' + * National Semiconductor LM75A + Prefix: 'lm75a' Addresses scanned: I2C 0x48 - 0x4f - Datasheet: Publicly available at the Dallas Semiconductor website - http://www.maxim-ic.com/ + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/ + * Dallas Semiconductor (now Maxim) DS75, DS1775, DS7505 + Prefixes: 'ds75', 'ds1775', 'ds7505' + Addresses scanned: none + Datasheet: Publicly available at the Maxim website + http://www.maximintegrated.com/ * Maxim MAX6625, MAX6626 - Prefix: 'lm75' - Addresses scanned: I2C 0x48 - 0x4b + Prefixes: 'max6625', 'max6626' + Addresses scanned: none Datasheet: Publicly available at the Maxim website http://www.maxim-ic.com/ * Microchip (TelCom) TCN75 - Prefix: 'lm75' - Addresses scanned: I2C 0x48 - 0x4f + Prefix: 'tcn75' + Addresses scanned: none Datasheet: Publicly available at the Microchip website http://www.microchip.com/ + * Microchip MCP9800, MCP9801, MCP9802, MCP9803 + Prefix: 'mcp980x' + Addresses scanned: none + Datasheet: Publicly available at the Microchip website + http://www.microchip.com/ + * Analog Devices ADT75 + Prefix: 'adt75' + Addresses scanned: none + Datasheet: Publicly available at the Analog Devices website + http://www.analog.com/adt75 + * ST Microelectronics STDS75 + Prefix: 'stds75' + Addresses scanned: none + Datasheet: Publicly available at the ST website + http://www.st.com/internet/analog/product/121769.jsp + * Texas Instruments TMP100, TMP101, TMP105, TMP75, TMP175, TMP275 + Prefixes: 'tmp100', 'tmp101', 'tmp105', 'tmp175', 'tmp75', 'tmp275' + Addresses scanned: none + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/product/tmp100 + http://www.ti.com/product/tmp101 + http://www.ti.com/product/tmp105 + http://www.ti.com/product/tmp75 + http://www.ti.com/product/tmp175 + http://www.ti.com/product/tmp275 Author: Frodo Looijaard <frodol@dds.nl> @@ -42,24 +67,20 @@ the temperature falls below the Hysteresis value. All temperatures are in degrees Celsius, and are guaranteed within a range of -55 to +125 degrees. -The LM75 only updates its values each 1.5 seconds; reading it more often +The driver caches the values for a period varying between 1 second for the +slowest chips and 125 ms for the fastest chips; reading it more often will do no harm, but will return 'old' values. -The LM75 is usually used in combination with LM78-like chips, to measure -the temperature of the processor(s). - -The DS75, DS1775, MAX6625, and MAX6626 are supported as well. -They are not distinguished from an LM75. While most of these chips -have three additional bits of accuracy (12 vs. 9 for the LM75), -the additional bits are not supported. Not only that, but these chips will -not be detected if not in 9-bit precision mode (use the force parameter if -needed). - -The TCN75 is supported as well, and is not distinguished from an LM75. +The original LM75 was typically used in combination with LM78-like chips +on PC motherboards, to measure the temperature of the processor(s). Clones +are now used in various embedded designs. The LM75 is essentially an industry standard; there may be other LM75 clones not listed here, with or without various enhancements, -that are supported. +that are supported. The clones are not detected by the driver, unless +they reproduce the exact register tricks of the original LM75, and must +therefore be instantiated explicitly. Higher resolution up to 12-bit +is supported by this driver, other specific enhancements are not. The LM77 is not supported, contrary to what we pretended for a long time. Both chips are simply not compatible, value encoding differs. diff --git a/Documentation/hwmon/lm77 b/Documentation/hwmon/lm77 index 57c3a46d637..bfc915fe363 100644 --- a/Documentation/hwmon/lm77 +++ b/Documentation/hwmon/lm77 @@ -18,5 +18,21 @@ sensor incorporates a band-gap type temperature sensor, 10-bit ADC, and a digital comparator with user-programmable upper and lower limit values. -Limits can be set through the Overtemperature Shutdown register and -Hysteresis register. +The LM77 implements 3 limits: low (temp1_min), high (temp1_max) and +critical (temp1_crit.) It also implements an hysteresis mechanism which +applies to all 3 limits. The relative difference is stored in a single +register on the chip, which means that the relative difference between +the limit and its hysteresis is always the same for all 3 limits. + +This implementation detail implies the following: +* When setting a limit, its hysteresis will automatically follow, the + difference staying unchanged. For example, if the old critical limit + was 80 degrees C, and the hysteresis was 75 degrees C, and you change + the critical limit to 90 degrees C, then the hysteresis will + automatically change to 85 degrees C. +* All 3 hysteresis can't be set independently. We decided to make + temp1_crit_hyst writable, while temp1_min_hyst and temp1_max_hyst are + read-only. Setting temp1_crit_hyst writes the difference between + temp1_crit_hyst and temp1_crit into the chip, and the same relative + hysteresis applies automatically to the low and high limits. +* The limits should be set before the hysteresis. diff --git a/Documentation/hwmon/lm78 b/Documentation/hwmon/lm78 index fd5dc7a19f0..4dd47731789 100644 --- a/Documentation/hwmon/lm78 +++ b/Documentation/hwmon/lm78 @@ -4,16 +4,17 @@ Kernel driver lm78 Supported chips: * National Semiconductor LM78 / LM78-J Prefix: 'lm78' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) + Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports) Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ * National Semiconductor LM79 Prefix: 'lm79' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) + Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports) Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ -Author: Frodo Looijaard <frodol@dds.nl> +Authors: Frodo Looijaard <frodol@dds.nl> + Jean Delvare <jdelvare@suse.de> Description ----------- @@ -56,16 +57,6 @@ should work with. This is hardcoded by the mainboard and/or processor itself. It is a value in volts. When it is unconnected, you will often find the value 3.50 V here. -In addition to the alarms described above, there are a couple of additional -ones. There is a BTI alarm, which gets triggered when an external chip has -crossed its limits. Usually, this is connected to all LM75 chips; if at -least one crosses its limits, this bit gets set. The CHAS alarm triggers -if your computer case is open. The FIFO alarms should never trigger; it -indicates an internal error. The SMI_IN alarm indicates some other chip -has triggered an SMI interrupt. As we do not use SMI interrupts at all, -this condition usually indicates there is a problem with some other -device. - If an alarm triggers, it will remain triggered until the hardware register is read at least once. This means that the cause for the alarm may already have disappeared! Note that in the current implementation, all diff --git a/Documentation/hwmon/lm80 b/Documentation/hwmon/lm80 index cb5b407ba3e..a60b43efc32 100644 --- a/Documentation/hwmon/lm80 +++ b/Documentation/hwmon/lm80 @@ -7,6 +7,11 @@ Supported chips: Addresses scanned: I2C 0x28 - 0x2f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ + * National Semiconductor LM96080 + Prefix: 'lm96080' + Addresses scanned: I2C 0x28 - 0x2f + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/ Authors: Frodo Looijaard <frodol@dds.nl>, @@ -17,7 +22,9 @@ Description This driver implements support for the National Semiconductor LM80. It is described as a 'Serial Interface ACPI-Compatible Microprocessor -System Hardware Monitor'. +System Hardware Monitor'. The LM96080 is a more recent incarnation, +it is pin and register compatible, with a few additional features not +yet supported by the driver. The LM80 implements one temperature sensor, two fan rotation speed sensors, seven voltage sensors, alarms, and some miscellaneous stuff. diff --git a/Documentation/hwmon/lm83 b/Documentation/hwmon/lm83 index 061d9ed8ff4..50be5cb26de 100644 --- a/Documentation/hwmon/lm83 +++ b/Documentation/hwmon/lm83 @@ -7,18 +7,23 @@ Supported chips: Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e Datasheet: Publicly available at the National Semiconductor website http://www.national.com/pf/LM/LM83.html + * National Semiconductor LM82 + Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/pf/LM/LM82.html -Author: Jean Delvare <khali@linux-fr.org> +Author: Jean Delvare <jdelvare@suse.de> Description ----------- The LM83 is a digital temperature sensor. It senses its own temperature as -well as the temperature of up to three external diodes. It is compatible -with many other devices such as the LM84 and all other ADM1021 clones. -The main difference between the LM83 and the LM84 in that the later can -only sense the temperature of one external diode. +well as the temperature of up to three external diodes. The LM82 is +a stripped down version of the LM83 that only supports one external diode. +Both are compatible with many other devices such as the LM84 and all +other ADM1021 clones. The main difference between the LM83 and the LM84 +in that the later can only sense the temperature of one external diode. Using the adm1021 driver for a LM83 should work, but only two temperatures will be reported instead of four. @@ -30,13 +35,17 @@ contact us. Note that the LM90 can easily be misdetected as a LM83. Confirmed motherboards: SBS P014 + SBS PSL09 Unconfirmed motherboards: Gigabyte GA-8IK1100 Iwill MPX2 Soltek SL-75DRV5 -The driver has been successfully tested by Magnus Forsström, who I'd +The LM82 is confirmed to have been found on most AMD Geode reference +designs and test platforms. + +The driver has been successfully tested by Magnus Forsström, who I'd like to thank here. More testers will be of course welcome. The fact that the LM83 is only scarcely used can be easily explained. diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85 index 9549237530c..7c49feaa79d 100644 --- a/Documentation/hwmon/lm85 +++ b/Documentation/hwmon/lm85 @@ -9,19 +9,31 @@ Supported chips: * Analog Devices ADM1027 Prefix: 'adm1027' Addresses scanned: I2C 0x2c, 0x2d, 0x2e - Datasheet: http://www.analog.com/en/prod/0,,766_825_ADM1027,00.html + Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADM1027 * Analog Devices ADT7463 Prefix: 'adt7463' Addresses scanned: I2C 0x2c, 0x2d, 0x2e - Datasheet: http://www.analog.com/en/prod/0,,766_825_ADT7463,00.html + Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADT7463 + * Analog Devices ADT7468 + Prefix: 'adt7468' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADT7468 * SMSC EMC6D100, SMSC EMC6D101 Prefix: 'emc6d100' Addresses scanned: I2C 0x2c, 0x2d, 0x2e - Datasheet: http://www.smsc.com/main/tools/discontinued/6d100.pdf + Datasheet: http://www.smsc.com/media/Downloads_Public/discontinued/6d100.pdf * SMSC EMC6D102 Prefix: 'emc6d102' Addresses scanned: I2C 0x2c, 0x2d, 0x2e Datasheet: http://www.smsc.com/main/catalog/emc6d102.html + * SMSC EMC6D103 + Prefix: 'emc6d103' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: http://www.smsc.com/main/catalog/emc6d103.html + * SMSC EMC6D103S + Prefix: 'emc6d103s' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: http://www.smsc.com/main/catalog/emc6d103s.html Authors: Philip Pokorny <ppokorny@penguincomputing.com>, @@ -34,7 +46,7 @@ Description ----------- This driver implements support for the National Semiconductor LM85 and -compatible chips including the Analog Devices ADM1027, ADT7463 and +compatible chips including the Analog Devices ADM1027, ADT7463, ADT7468 and SMSC EMC6D10x chips family. The LM85 uses the 2-wire interface compatible with the SMBUS 2.0 @@ -87,19 +99,22 @@ To smooth the response of fans to changes in temperature, the LM85 has an optional filter for smoothing temperatures. The ADM1027 has the same config option but uses it to rate limit the changes to fan speed instead. -The ADM1027 and ADT7463 have a 10-bit ADC and can therefore measure -temperatures with 0.25 degC resolution. They also provide an offset to the -temperature readings that is automatically applied during measurement. -This offset can be used to zero out any errors due to traces and placement. -The documentation says that the offset is in 0.25 degC steps, but in -initial testing of the ADM1027 it was 1.00 degC steps. Analog Devices has -confirmed this "bug". The ADT7463 is reported to work as described in the -documentation. The current lm85 driver does not show the offset register. - -The ADT7463 has a THERM asserted counter. This counter has a 22.76ms -resolution and a range of 5.8 seconds. The driver implements a 32-bit -accumulator of the counter value to extend the range to over a year. The -counter will stay at it's max value until read. +The ADM1027, ADT7463 and ADT7468 have a 10-bit ADC and can therefore +measure temperatures with 0.25 degC resolution. They also provide an offset +to the temperature readings that is automatically applied during +measurement. This offset can be used to zero out any errors due to traces +and placement. The documentation says that the offset is in 0.25 degC +steps, but in initial testing of the ADM1027 it was 1.00 degC steps. Analog +Devices has confirmed this "bug". The ADT7463 is reported to work as +described in the documentation. The current lm85 driver does not show the +offset register. + +The ADT7468 has a high-frequency PWM mode, where all PWM outputs are +driven by a 22.5 kHz clock. This is a global mode, not per-PWM output, +which means that setting any PWM frequency above 11.3 kHz will switch +all 3 PWM outputs to a 22.5 kHz frequency. Conversely, setting any PWM +frequency below 11.3 kHz will switch all 3 PWM outputs to a frequency +between 10 and 100 Hz, which can then be tuned separately. See the vendor datasheets for more information. There is application note from National (AN-1260) with some additional information about the LM85. @@ -115,9 +130,11 @@ to be register compatible. The EMC6D100 offers all the features of the EMC6D101 plus additional voltage monitoring and system control features. Unfortunately it is not possible to distinguish between the package versions on register level so these additional voltage inputs may read -zero. The EMC6D102 features addtional ADC bits thus extending precision +zero. EMC6D102 and EMC6D103 feature additional ADC bits thus extending precision of voltage and temperature channels. +SMSC EMC6D103S is similar to EMC6D103, but does not support pwm#_auto_pwm_minctl +and temp#_auto_temp_off. Hardware Configurations ----------------------- @@ -130,17 +147,17 @@ datasheet for a complete description of the differences. Other than identifying the chip, the driver behaves no differently with regard to these two chips. The LM85B is recommended for new designs. -The ADM1027 and ADT7463 chips have an optional SMBALERT output that can be -used to signal the chipset in case a limit is exceeded or the temperature -sensors fail. Individual sensor interrupts can be masked so they won't -trigger SMBALERT. The SMBALERT output if configured replaces one of the other -functions (PWM2 or IN0). This functionality is not implemented in current -driver. +The ADM1027, ADT7463 and ADT7468 chips have an optional SMBALERT output +that can be used to signal the chipset in case a limit is exceeded or the +temperature sensors fail. Individual sensor interrupts can be masked so +they won't trigger SMBALERT. The SMBALERT output if configured replaces one +of the other functions (PWM2 or IN0). This functionality is not implemented +in current driver. -The ADT7463 also has an optional THERM output/input which can be connected -to the processor PROC_HOT output. If available, the autofan control -dynamic Tmin feature can be enabled to keep the system temperature within -spec (just?!) with the least possible fan noise. +The ADT7463 and ADT7468 also have an optional THERM output/input which can +be connected to the processor PROC_HOT output. If available, the autofan +control dynamic Tmin feature can be enabled to keep the system temperature +within spec (just?!) with the least possible fan noise. Configuration Notes ------------------- @@ -162,24 +179,14 @@ temperature configuration points: There are three PWM outputs. The LM85 datasheet suggests that the pwm3 output control both fan3 and fan4. Each PWM can be individually -configured and assigned to a zone for it's control value. Each PWM can be +configured and assigned to a zone for its control value. Each PWM can be configured individually according to the following options. * pwm#_auto_pwm_min - this specifies the PWM value for temp#_auto_temp_off temperature. (PWM value from 0 to 255) -* pwm#_auto_pwm_freq - select base frequency of PWM output. You can select - in range of 10.0 to 94.0 Hz in .1 Hz units. - (Values 100 to 940). - -The pwm#_auto_pwm_freq can be set to one of the following 8 values. Setting the -frequency to a value not on this list, will result in the next higher frequency -being selected. The actual device frequency may vary slightly from this -specification as designed by the manufacturer. Consult the datasheet for more -details. (PWM Frequency values: 100, 150, 230, 300, 380, 470, 620, 940) - * pwm#_auto_pwm_minctl - this flags selects for temp#_auto_temp_off temperature - the bahaviour of fans. Write 1 to let fans spinning at + the behaviour of fans. Write 1 to let fans spinning at pwm#_auto_pwm_min or write 0 to let them off. NOTE: It has been reported that there is a bug in the LM85 that causes the flag @@ -206,16 +213,18 @@ Configuration choices: The National LM85's have two vendor specific configuration features. Tach. mode and Spinup Control. For more details on these, -see the LM85 datasheet or Application Note AN-1260. +see the LM85 datasheet or Application Note AN-1260. These features +are not currently supported by the lm85 driver. The Analog Devices ADM1027 has several vendor specific enhancements. The number of pulses-per-rev of the fans can be set, Tach monitoring can be optimized for PWM operation, and an offset can be applied to the temperatures to compensate for systemic errors in the -measurements. +measurements. These features are not currently supported by the lm85 +driver. -In addition to the ADM1027 features, the ADT7463 also has Tmin control -and THERM asserted counts. Automatic Tmin control acts to adjust the -Tmin value to maintain the measured temperature sensor at a specified -temperature. There isn't much documentation on this feature in the -ADT7463 data sheet. This is not supported by current driver. +In addition to the ADM1027 features, the ADT7463 and ADT7468 also have +Tmin control and THERM asserted counts. Automatic Tmin control acts to +adjust the Tmin value to maintain the measured temperature sensor at a +specified temperature. There isn't much documentation on this feature in +the ADT7463 data sheet. This is not supported by current driver. diff --git a/Documentation/hwmon/lm87 b/Documentation/hwmon/lm87 index c952c57f0e1..a2339fd9acb 100644 --- a/Documentation/hwmon/lm87 +++ b/Documentation/hwmon/lm87 @@ -4,8 +4,12 @@ Kernel driver lm87 Supported chips: * National Semiconductor LM87 Prefix: 'lm87' - Addresses scanned: I2C 0x2c - 0x2f + Addresses scanned: I2C 0x2c - 0x2e Datasheet: http://www.national.com/pf/LM/LM87.html + * Analog Devices ADM1024 + Prefix: 'adm1024' + Addresses scanned: I2C 0x2c - 0x2e + Datasheet: http://www.analog.com/en/prod/0,2877,ADM1024,00.html Authors: Frodo Looijaard <frodol@dds.nl>, @@ -13,17 +17,18 @@ Authors: Mark Studebaker <mdsxyz123@yahoo.com>, Stephen Rousset <stephen.rousset@rocketlogix.com>, Dan Eaton <dan.eaton@rocketlogix.com>, - Jean Delvare <khali@linux-fr.org>, + Jean Delvare <jdelvare@suse.de>, Original 2.6 port Jeff Oliver Description ----------- -This driver implements support for the National Semiconductor LM87. +This driver implements support for the National Semiconductor LM87 +and the Analog Devices ADM1024. The LM87 implements up to three temperature sensors, up to two fan rotation speed sensors, up to seven voltage sensors, alarms, and some -miscellaneous stuff. +miscellaneous stuff. The ADM1024 is fully compatible. Temperatures are measured in degrees Celsius. Each input has a high and low alarm settings. A high limit produces an alarm when the value @@ -60,11 +65,10 @@ The LM87 has four pins which can serve one of two possible functions, depending on the hardware configuration. Some functions share pins, so not all functions are available at the same -time. Which are depends on the hardware setup. This driver assumes that -the BIOS configured the chip correctly. In that respect, it differs from -the original driver (from lm_sensors for Linux 2.4), which would force the -LM87 to an arbitrary, compile-time chosen mode, regardless of the actual -chipset wiring. +time. Which are depends on the hardware setup. This driver normally +assumes that firmware configured the chip correctly. Where this is not +the case, platform code must set the I2C client's platform_data to point +to a u8 value to be written to the channel register. For reference, here is the list of exclusive functions: - in0+in5 (default) or temp3 diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90 index 438cb24cee5..8122675d30f 100644 --- a/Documentation/hwmon/lm90 +++ b/Documentation/hwmon/lm90 @@ -8,10 +8,10 @@ Supported chips: Datasheet: Publicly available at the National Semiconductor website http://www.national.com/pf/LM/LM90.html * National Semiconductor LM89 - Prefix: 'lm99' + Prefix: 'lm89' (no auto-detection) Addresses scanned: I2C 0x4c and 0x4d Datasheet: Publicly available at the National Semiconductor website - http://www.national.com/pf/LM/LM89.html + http://www.national.com/mpf/LM/LM89.html * National Semiconductor LM99 Prefix: 'lm99' Addresses scanned: I2C 0x4c and 0x4d @@ -21,18 +21,47 @@ Supported chips: Prefix: 'lm86' Addresses scanned: I2C 0x4c Datasheet: Publicly available at the National Semiconductor website - http://www.national.com/pf/LM/LM86.html + http://www.national.com/mpf/LM/LM86.html * Analog Devices ADM1032 Prefix: 'adm1032' Addresses scanned: I2C 0x4c and 0x4d - Datasheet: Publicly available at the Analog Devices website - http://www.analog.com/en/prod/0,2877,ADM1032,00.html + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=ADM1032 * Analog Devices ADT7461 Prefix: 'adt7461' Addresses scanned: I2C 0x4c and 0x4d - Datasheet: Publicly available at the Analog Devices website - http://www.analog.com/en/prod/0,2877,ADT7461,00.html - Note: Only if in ADM1032 compatibility mode + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461 + * Analog Devices ADT7461A + Prefix: 'adt7461a' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461A + * ON Semiconductor NCT1008 + Prefix: 'nct1008' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=NCT1008 + * Maxim MAX6646 + Prefix: 'max6646' + Addresses scanned: I2C 0x4d + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497 + * Maxim MAX6647 + Prefix: 'max6646' + Addresses scanned: I2C 0x4e + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497 + * Maxim MAX6648 + Prefix: 'max6646' + Addresses scanned: I2C 0x4c + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500 + * Maxim MAX6649 + Prefix: 'max6646' + Addresses scanned: I2C 0x4c + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497 * Maxim MAX6657 Prefix: 'max6657' Addresses scanned: I2C 0x4c @@ -44,13 +73,63 @@ Supported chips: Datasheet: Publicly available at the Maxim website http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578 * Maxim MAX6659 - Prefix: 'max6657' - Addresses scanned: I2C 0x4c, 0x4d (unsupported 0x4e) + Prefix: 'max6659' + Addresses scanned: I2C 0x4c, 0x4d, 0x4e Datasheet: Publicly available at the Maxim website http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578 + * Maxim MAX6680 + Prefix: 'max6680' + Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, + 0x4c, 0x4d and 0x4e + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370 + * Maxim MAX6681 + Prefix: 'max6680' + Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, + 0x4c, 0x4d and 0x4e + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370 + * Maxim MAX6692 + Prefix: 'max6646' + Addresses scanned: I2C 0x4c + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500 + * Maxim MAX6695 + Prefix: 'max6695' + Addresses scanned: I2C 0x18 + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/datasheet/index.mvp/id/4199 + * Maxim MAX6696 + Prefix: 'max6695' + Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, + 0x4c, 0x4d and 0x4e + Datasheet: Publicly available at the Maxim website + http://www.maxim-ic.com/datasheet/index.mvp/id/4199 + * Winbond/Nuvoton W83L771W/G + Prefix: 'w83l771' + Addresses scanned: I2C 0x4c + Datasheet: No longer available + * Winbond/Nuvoton W83L771AWG/ASG + Prefix: 'w83l771' + Addresses scanned: I2C 0x4c + Datasheet: Not publicly available, can be requested from Nuvoton + * Philips/NXP SA56004X + Prefix: 'sa56004' + Addresses scanned: I2C 0x48 through 0x4F + Datasheet: Publicly available at NXP website + http://ics.nxp.com/products/interface/datasheet/sa56004x.pdf + * GMT G781 + Prefix: 'g781' + Addresses scanned: I2C 0x4c, 0x4d + Datasheet: Not publicly available from GMT + * Texas Instruments TMP451 + Prefix: 'tmp451' + Addresses scanned: I2C 0x4c + Datasheet: Publicly available at TI website + http://www.ti.com/litv/pdf/sbos686 -Author: Jean Delvare <khali@linux-fr.org> +Author: Jean Delvare <jdelvare@suse.de> Description @@ -58,21 +137,22 @@ Description The LM90 is a digital temperature sensor. It senses its own temperature as well as the temperature of up to one external diode. It is compatible -with many other devices such as the LM86, the LM89, the LM99, the ADM1032, -the MAX6657, MAX6658 and the MAX6659 all of which are supported by this driver. -Note that there is no easy way to differentiate between the last three -variants. The extra address and features of the MAX6659 are not supported by -this driver. Additionally, the ADT7461 is supported if found in ADM1032 -compatibility mode. +with many other devices, many of which are supported by this driver. + +Note that there is no easy way to differentiate between the MAX6657, +MAX6658 and MAX6659 variants. The extra features of the MAX6659 are only +supported by this driver if the chip is located at address 0x4d or 0x4e, +or if the chip type is explicitly selected as max6659. +The MAX6680 and MAX6681 only differ in their pinout, therefore they obviously +can't (and don't need to) be distinguished. The specificity of this family of chipsets over the ADM1021/LM84 family is that it features critical limits with hysteresis, and an increased resolution of the remote temperature measurement. The different chipsets of the family are not strictly identical, although -very similar. This driver doesn't handle any specific feature for now, -with the exception of SMBus PEC. For reference, here comes a non-exhaustive -list of specific features: +very similar. For reference, here comes a non-exhaustive list of specific +features: LM90: * Filter and alert configuration register at 0xBF. @@ -93,21 +173,47 @@ ADM1032: * ALERT is triggered by open remote sensor. * SMBus PEC support for Write Byte and Receive Byte transactions. -ADT7461 +ADT7461, ADT7461A, NCT1008: * Extended temperature range (breaks compatibility) * Lower resolution for remote temperature MAX6657 and MAX6658: + * Better local resolution * Remote sensor type selection -MAX6659 +MAX6659: + * Better local resolution * Selectable address * Second critical temperature limit * Remote sensor type selection +MAX6680 and MAX6681: + * Selectable address + * Remote sensor type selection + +MAX6695 and MAX6696: + * Better local resolution + * Selectable address (max6696) + * Second critical temperature limit + * Two remote sensors + +W83L771W/G + * The G variant is lead-free, otherwise similar to the W. + * Filter and alert configuration register at 0xBF + * Moving average (depending on conversion rate) + +W83L771AWG/ASG + * Successor of the W83L771W/G, same features. + * The AWG and ASG variants only differ in package format. + * Diode ideality factor configuration (remote sensor) at 0xE3 + +SA56004X: + * Better local resolution + All temperature values are given in degrees Celsius. Resolution is 1.0 degree for the local temperature, 0.125 degree for the remote -temperature. +temperature, except for the MAX6657, MAX6658 and MAX6659 which have a +resolution of 0.125 degree for both temperatures. Each sensor has its own high and low limits, plus a critical limit. Additionally, there is a relative hysteresis value common to both critical @@ -116,9 +222,22 @@ are exported, one for each channel, but these values are of course linked. Only the local hysteresis can be set from user-space, and the same delta applies to the remote hysteresis. -The lm90 driver will not update its values more frequently than every -other second; reading them more often will do no harm, but will return -'old' values. +The lm90 driver will not update its values more frequently than configured with +the update_interval attribute; reading them more often will do no harm, but will +return 'old' values. + +SMBus Alert Support +------------------- + +This driver has basic support for SMBus alert. When an alert is received, +the status register is read and the faulty temperature channel is logged. + +The Analog Devices chips (ADM1032, ADT7461 and ADT7461A) and ON +Semiconductor chips (NCT1008) do not implement the SMBus alert protocol +properly so additional care is needed: the ALERT output is disabled when +an alert is received, and is re-enabled only when the alarm is gone. +Otherwise the chip would block alerts from other chips in the bus as long +as the alarm is active. PEC Support ----------- @@ -141,7 +260,7 @@ SMBus Read Byte, and PEC will work properly. Additionally, the ADM1032 doesn't support SMBus Send Byte with PEC. Instead, it will try to write the PEC value to the register (because the SMBus Send Byte transaction with PEC is similar to a Write Byte transaction -without PEC), which is not what we want. Thus, PEC is explicitely disabled +without PEC), which is not what we want. Thus, PEC is explicitly disabled on SMBus Send Byte transactions in the lm90 driver. PEC on byte data transactions represents a significant increase in bandwidth diff --git a/Documentation/hwmon/lm92 b/Documentation/hwmon/lm92 index 7705bfaa070..22f68ad032c 100644 --- a/Documentation/hwmon/lm92 +++ b/Documentation/hwmon/lm92 @@ -19,7 +19,7 @@ Supported chips: Authors: Abraham van der Merwe <abraham@2d3d.co.za> - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Description diff --git a/Documentation/hwmon/lm93 b/Documentation/hwmon/lm93 new file mode 100644 index 00000000000..f3b2ad2ceb0 --- /dev/null +++ b/Documentation/hwmon/lm93 @@ -0,0 +1,309 @@ +Kernel driver lm93 +================== + +Supported chips: + * National Semiconductor LM93 + Prefix 'lm93' + Addresses scanned: I2C 0x2c-0x2e + Datasheet: http://www.national.com/ds.cgi/LM/LM93.pdf + * National Semiconductor LM94 + Prefix 'lm94' + Addresses scanned: I2C 0x2c-0x2e + Datasheet: http://www.national.com/ds.cgi/LM/LM94.pdf + +Authors: + Mark M. Hoffman <mhoffman@lightlink.com> + Ported to 2.6 by Eric J. Bowersox <ericb@aspsys.com> + Adapted to 2.6.20 by Carsten Emde <ce@osadl.org> + Modified for mainline integration by Hans J. Koch <hjk@hansjkoch.de> + +Module Parameters +----------------- + +* init: integer + Set to non-zero to force some initializations (default is 0). +* disable_block: integer + A "0" allows SMBus block data transactions if the host supports them. A "1" + disables SMBus block data transactions. The default is 0. +* vccp_limit_type: integer array (2) + Configures in7 and in8 limit type, where 0 means absolute and non-zero + means relative. "Relative" here refers to "Dynamic Vccp Monitoring using + VID" from the datasheet. It greatly simplifies the interface to allow + only one set of limits (absolute or relative) to be in operation at a + time (even though the hardware is capable of enabling both). There's + not a compelling use case for enabling both at once, anyway. The default + is "0,0". +* vid_agtl: integer + A "0" configures the VID pins for V(ih) = 2.1V min, V(il) = 0.8V max. + A "1" configures the VID pins for V(ih) = 0.8V min, V(il) = 0.4V max. + (The latter setting is referred to as AGTL+ Compatible in the datasheet.) + I.e. this parameter controls the VID pin input thresholds; if your VID + inputs are not working, try changing this. The default value is "0". + + +Hardware Description +-------------------- + +(from the datasheet) + +The LM93 hardware monitor has a two wire digital interface compatible with +SMBus 2.0. Using an 8-bit ADC, the LM93 measures the temperature of two remote +diode connected transistors as well as its own die and 16 power supply +voltages. To set fan speed, the LM93 has two PWM outputs that are each +controlled by up to four temperature zones. The fancontrol algorithm is lookup +table based. The LM93 includes a digital filter that can be invoked to smooth +temperature readings for better control of fan speed. The LM93 has four +tachometer inputs to measure fan speed. Limit and status registers for all +measured values are included. The LM93 builds upon the functionality of +previous motherboard management ASICs and uses some of the LM85's features +(i.e. smart tachometer mode). It also adds measurement and control support +for dynamic Vccp monitoring and PROCHOT. It is designed to monitor a dual +processor Xeon class motherboard with a minimum of external components. + +LM94 is also supported in LM93 compatible mode. Extra sensors and features of +LM94 are not supported. + + +User Interface +-------------- + +#PROCHOT: + +The LM93 can monitor two #PROCHOT signals. The results are found in the +sysfs files prochot1, prochot2, prochot1_avg, prochot2_avg, prochot1_max, +and prochot2_max. prochot1_max and prochot2_max contain the user limits +for #PROCHOT1 and #PROCHOT2, respectively. prochot1 and prochot2 contain +the current readings for the most recent complete time interval. The +value of prochot1_avg and prochot2_avg is something like a 2 period +exponential moving average (but not quite - check the datasheet). Note +that this third value is calculated by the chip itself. All values range +from 0-255 where 0 indicates no throttling, and 255 indicates > 99.6%. + +The monitoring intervals for the two #PROCHOT signals is also configurable. +These intervals can be found in the sysfs files prochot1_interval and +prochot2_interval. The values in these files specify the intervals for +#P1_PROCHOT and #P2_PROCHOT, respectively. Selecting a value not in this +list will cause the driver to use the next largest interval. The available +intervals are (in seconds): + +#PROCHOT intervals: 0.73, 1.46, 2.9, 5.8, 11.7, 23.3, 46.6, 93.2, 186, 372 + +It is possible to configure the LM93 to logically short the two #PROCHOT +signals. I.e. when #P1_PROCHOT is asserted, the LM93 will automatically +assert #P2_PROCHOT, and vice-versa. This mode is enabled by writing a +non-zero integer to the sysfs file prochot_short. + +The LM93 can also override the #PROCHOT pins by driving a PWM signal onto +one or both of them. When overridden, the signal has a period of 3.56 ms, +a minimum pulse width of 5 clocks (at 22.5kHz => 6.25% duty cycle), and +a maximum pulse width of 80 clocks (at 22.5kHz => 99.88% duty cycle). + +The sysfs files prochot1_override and prochot2_override contain boolean +integers which enable or disable the override function for #P1_PROCHOT and +#P2_PROCHOT, respectively. The sysfs file prochot_override_duty_cycle +contains a value controlling the duty cycle for the PWM signal used when +the override function is enabled. This value ranges from 0 to 15, with 0 +indicating minimum duty cycle and 15 indicating maximum. + +#VRD_HOT: + +The LM93 can monitor two #VRD_HOT signals. The results are found in the +sysfs files vrdhot1 and vrdhot2. There is one value per file: a boolean for +which 1 indicates #VRD_HOT is asserted and 0 indicates it is negated. These +files are read-only. + +Smart Tach Mode: + +(from the datasheet) + + If a fan is driven using a low-side drive PWM, the tachometer + output of the fan is corrupted. The LM93 includes smart tachometer + circuitry that allows an accurate tachometer reading to be + achieved despite the signal corruption. In smart tach mode all + four signals are measured within 4 seconds. + +Smart tach mode is enabled by the driver by writing 1 or 2 (associating the +the fan tachometer with a pwm) to the sysfs file fan<n>_smart_tach. A zero +will disable the function for that fan. Note that Smart tach mode cannot be +enabled if the PWM output frequency is 22500 Hz (see below). + +Manual PWM: + +The LM93 has a fixed or override mode for the two PWM outputs (although, there +are still some conditions that will override even this mode - see section +15.10.6 of the datasheet for details.) The sysfs files pwm1_override +and pwm2_override are used to enable this mode; each is a boolean integer +where 0 disables and 1 enables the manual control mode. The sysfs files pwm1 +and pwm2 are used to set the manual duty cycle; each is an integer (0-255) +where 0 is 0% duty cycle, and 255 is 100%. Note that the duty cycle values +are constrained by the hardware. Selecting a value which is not available +will cause the driver to use the next largest value. Also note: when manual +PWM mode is disabled, the value of pwm1 and pwm2 indicates the current duty +cycle chosen by the h/w. + +PWM Output Frequency: + +The LM93 supports several different frequencies for the PWM output channels. +The sysfs files pwm1_freq and pwm2_freq are used to select the frequency. The +frequency values are constrained by the hardware. Selecting a value which is +not available will cause the driver to use the next largest value. Also note +that this parameter has implications for the Smart Tach Mode (see above). + +PWM Output Frequencies (in Hz): 12, 36, 48, 60, 72, 84, 96, 22500 (default) + +Automatic PWM: + +The LM93 is capable of complex automatic fan control, with many different +points of configuration. To start, each PWM output can be bound to any +combination of eight control sources. The final PWM is the largest of all +individual control sources to which the PWM output is bound. + +The eight control sources are: temp1-temp4 (aka "zones" in the datasheet), +#PROCHOT 1 & 2, and #VRDHOT 1 & 2. The bindings are expressed as a bitmask +in the sysfs files pwm<n>_auto_channels, where a "1" enables the binding, and +a "0" disables it. The h/w default is 0x0f (all temperatures bound). + + 0x01 - Temp 1 + 0x02 - Temp 2 + 0x04 - Temp 3 + 0x08 - Temp 4 + 0x10 - #PROCHOT 1 + 0x20 - #PROCHOT 2 + 0x40 - #VRDHOT 1 + 0x80 - #VRDHOT 2 + +The function y = f(x) takes a source temperature x to a PWM output y. This +function of the LM93 is derived from a base temperature and a table of 12 +temperature offsets. The base temperature is expressed in degrees C in the +sysfs files temp<n>_auto_base. The offsets are expressed in cumulative +degrees C, with the value of offset <i> for temperature value <n> being +contained in the file temp<n>_auto_offset<i>. E.g. if the base temperature +is 40C: + + offset # temp<n>_auto_offset<i> range pwm + 1 0 - 25.00% + 2 0 - 28.57% + 3 1 40C - 41C 32.14% + 4 1 41C - 42C 35.71% + 5 2 42C - 44C 39.29% + 6 2 44C - 46C 42.86% + 7 2 48C - 50C 46.43% + 8 2 50C - 52C 50.00% + 9 2 52C - 54C 53.57% + 10 2 54C - 56C 57.14% + 11 2 56C - 58C 71.43% + 12 2 58C - 60C 85.71% + > 60C 100.00% + +Valid offsets are in the range 0C <= x <= 7.5C in 0.5C increments. + +There is an independent base temperature for each temperature channel. Note, +however, there are only two tables of offsets: one each for temp[12] and +temp[34]. Therefore, any change to e.g. temp1_auto_offset<i> will also +affect temp2_auto_offset<i>. + +The LM93 can also apply hysteresis to the offset table, to prevent unwanted +oscillation between two steps in the offsets table. These values are found in +the sysfs files temp<n>_auto_offset_hyst. The value in this file has the +same representation as in temp<n>_auto_offset<i>. + +If a temperature reading falls below the base value for that channel, the LM93 +will use the minimum PWM value. These values are found in the sysfs files +temp<n>_auto_pwm_min. Note, there are only two minimums: one each for temp[12] +and temp[34]. Therefore, any change to e.g. temp1_auto_pwm_min will also +affect temp2_auto_pwm_min. + +PWM Spin-Up Cycle: + +A spin-up cycle occurs when a PWM output is commanded from 0% duty cycle to +some value > 0%. The LM93 supports a minimum duty cycle during spin-up. These +values are found in the sysfs files pwm<n>_auto_spinup_min. The value in this +file has the same representation as other PWM duty cycle values. The +duration of the spin-up cycle is also configurable. These values are found in +the sysfs files pwm<n>_auto_spinup_time. The value in this file is +the spin-up time in seconds. The available spin-up times are constrained by +the hardware. Selecting a value which is not available will cause the driver +to use the next largest value. + +Spin-up Durations: 0 (disabled, h/w default), 0.1, 0.25, 0.4, 0.7, 1.0, + 2.0, 4.0 + +#PROCHOT and #VRDHOT PWM Ramping: + +If the #PROCHOT or #VRDHOT signals are asserted while bound to a PWM output +channel, the LM93 will ramp the PWM output up to 100% duty cycle in discrete +steps. The duration of each step is configurable. There are two files, with +one value each in seconds: pwm_auto_prochot_ramp and pwm_auto_vrdhot_ramp. +The available ramp times are constrained by the hardware. Selecting a value +which is not available will cause the driver to use the next largest value. + +Ramp Times: 0 (disabled, h/w default) to 0.75 in 0.05 second intervals + +Fan Boost: + +For each temperature channel, there is a boost temperature: if the channel +exceeds this limit, the LM93 will immediately drive both PWM outputs to 100%. +This limit is expressed in degrees C in the sysfs files temp<n>_auto_boost. +There is also a hysteresis temperature for this function: after the boost +limit is reached, the temperature channel must drop below this value before +the boost function is disabled. This temperature is also expressed in degrees +C in the sysfs files temp<n>_auto_boost_hyst. + +GPIO Pins: + +The LM93 can monitor the logic level of four dedicated GPIO pins as well as the +four tach input pins. GPIO0-GPIO3 correspond to (fan) tach 1-4, respectively. +All eight GPIOs are read by reading the bitmask in the sysfs file gpio. The +LSB is GPIO0, and the MSB is GPIO7. + + +LM93 Unique sysfs Files +----------------------- + + file description + ------------------------------------------------------------- + + prochot<n> current #PROCHOT % + + prochot<n>_avg moving average #PROCHOT % + + prochot<n>_max limit #PROCHOT % + + prochot_short enable or disable logical #PROCHOT pin short + + prochot<n>_override force #PROCHOT assertion as PWM + + prochot_override_duty_cycle + duty cycle for the PWM signal used when + #PROCHOT is overridden + + prochot<n>_interval #PROCHOT PWM sampling interval + + vrdhot<n> 0 means negated, 1 means asserted + + fan<n>_smart_tach enable or disable smart tach mode + + pwm<n>_auto_channels select control sources for PWM outputs + + pwm<n>_auto_spinup_min minimum duty cycle during spin-up + + pwm<n>_auto_spinup_time duration of spin-up + + pwm_auto_prochot_ramp ramp time per step when #PROCHOT asserted + + pwm_auto_vrdhot_ramp ramp time per step when #VRDHOT asserted + + temp<n>_auto_base temperature channel base + + temp<n>_auto_offset[1-12] + temperature channel offsets + + temp<n>_auto_offset_hyst + temperature channel offset hysteresis + + temp<n>_auto_boost temperature channel boost (PWMs to 100%) limit + + temp<n>_auto_boost_hyst temperature channel boost hysteresis + + gpio input state of 8 GPIO pins; read-only + diff --git a/Documentation/hwmon/lm95234 b/Documentation/hwmon/lm95234 new file mode 100644 index 00000000000..a0e95ddfd37 --- /dev/null +++ b/Documentation/hwmon/lm95234 @@ -0,0 +1,36 @@ +Kernel driver lm95234 +===================== + +Supported chips: + * National Semiconductor / Texas Instruments LM95234 + Addresses scanned: I2C 0x18, 0x4d, 0x4e + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/product/lm95234 + + +Author: Guenter Roeck <linux@roeck-us.net> + +Description +----------- + +LM95234 is an 11-bit digital temperature sensor with a 2-wire System Management +Bus (SMBus) interface and TrueTherm technology that can very accurately monitor +the temperature of four remote diodes as well as its own temperature. +The four remote diodes can be external devices such as microprocessors, +graphics processors or diode-connected 2N3904s. The LM95234's TruTherm +beta compensation technology allows sensing of 90 nm or 65 nm process +thermal diodes accurately. + +All temperature values are given in millidegrees Celsius. Temperature +is provided within a range of -127 to +255 degrees (+127.875 degrees for +the internal sensor). Resolution depends on temperature input and range. + +Each sensor has its own maximum limit, but the hysteresis is common to all +channels. The hysteresis is configurable with the tem1_max_hyst attribute and +affects the hysteresis on all channels. The first two external sensors also +have a critical limit. + +The lm95234 driver can change its update interval to a fixed set of values. +It will round up to the next selectable interval. See the datasheet for exact +values. Reading sensor values more often will do no harm, but will return +'old' values. diff --git a/Documentation/hwmon/lm95245 b/Documentation/hwmon/lm95245 new file mode 100644 index 00000000000..77eaf2812d2 --- /dev/null +++ b/Documentation/hwmon/lm95245 @@ -0,0 +1,37 @@ +Kernel driver lm95245 +================== + +Supported chips: + * National Semiconductor LM95245 + Addresses scanned: I2C 0x18, 0x19, 0x29, 0x4c, 0x4d + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/mpf/LM/LM95245.html + + +Author: Alexander Stein <alexander.stein@systec-electronic.com> + +Description +----------- + +The LM95245 is an 11-bit digital temperature sensor with a 2-wire System +Management Bus (SMBus) interface and TruTherm technology that can monitor +the temperature of a remote diode as well as its own temperature. +The LM95245 can be used to very accurately monitor the temperature of +external devices such as microprocessors. + +All temperature values are given in millidegrees Celsius. Local temperature +is given within a range of -127 to +127.875 degrees. Remote temperatures are +given within a range of -127 to +255 degrees. Resolution depends on +temperature input and range. + +Each sensor has its own critical limit. Additionally, there is a relative +hysteresis value common to both critical limits. To make life easier to +user-space applications, two absolute values are exported, one for each +channel, but these values are of course linked. Only the local hysteresis +can be set from user-space, and the same delta applies to the remote +hysteresis. + +The lm95245 driver can change its update interval to a fixed set of values. +It will round up to the next selectable interval. See the datasheet for exact +values. Reading sensor values more often will do no harm, but will return +'old' values. diff --git a/Documentation/hwmon/ltc2945 b/Documentation/hwmon/ltc2945 new file mode 100644 index 00000000000..f8d0f7f19ad --- /dev/null +++ b/Documentation/hwmon/ltc2945 @@ -0,0 +1,84 @@ +Kernel driver ltc2945 +===================== + +Supported chips: + * Linear Technology LTC2945 + Prefix: 'ltc2945' + Addresses scanned: - + Datasheet: + http://cds.linear.com/docs/en/datasheet/2945fa.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +The LTC2945 is a rail-to-rail system monitor that measures current, voltage, +and power consumption. + + +Usage Notes +----------- + +This driver does not probe for LTC2945 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC2945 at address 0x10 +on I2C bus #1: +$ modprobe ltc2945 +$ echo ltc2945 0x10 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADC +registers. If a set of voltage divider resistors is installed, calculate the +real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the +value of the divider resistor against the measured voltage and R2 is the value +of the divider resistor against Ground. + +Current reading provided by this driver is reported as obtained from the ADC +Current Sense register. The reported value assumes that a 1 mOhm sense resistor +is installed. If a different sense resistor is installed, calculate the real +current by dividing the reported value by the sense resistor value in mOhm. + +in1_input VIN voltage (mV). Voltage is measured either at + SENSE+ or VDD pin depending on chip configuration. +in1_min Undervoltage threshold +in1_max Overvoltage threshold +in1_lowest Lowest measured voltage +in1_highest Highest measured voltage +in1_reset_history Write 1 to reset in1 history +in1_min_alarm Undervoltage alarm +in1_max_alarm Overvoltage alarm + +in2_input ADIN voltage (mV) +in2_min Undervoltage threshold +in2_max Overvoltage threshold +in2_lowest Lowest measured voltage +in2_highest Highest measured voltage +in2_reset_history Write 1 to reset in2 history +in2_min_alarm Undervoltage alarm +in2_max_alarm Overvoltage alarm + +curr1_input SENSE current (mA) +curr1_min Undercurrent threshold +curr1_max Overcurrent threshold +curr1_lowest Lowest measured current +curr1_highest Highest measured current +curr1_reset_history Write 1 to reset curr1 history +curr1_min_alarm Undercurrent alarm +curr1_max_alarm Overcurrent alarm + +power1_input Power (in uW). Power is calculated based on SENSE+/VDD + voltage or ADIN voltage depending on chip configuration. +power1_min Low lower threshold +power1_max High power threshold +power1_input_lowest Historical minimum power use +power1_input_highest Historical maximum power use +power1_reset_history Write 1 to reset power1 history +power1_min_alarm Low power alarm +power1_max_alarm High power alarm diff --git a/Documentation/hwmon/ltc2978 b/Documentation/hwmon/ltc2978 new file mode 100644 index 00000000000..686c078bb0e --- /dev/null +++ b/Documentation/hwmon/ltc2978 @@ -0,0 +1,157 @@ +Kernel driver ltc2978 +===================== + +Supported chips: + * Linear Technology LTC2974 + Prefix: 'ltc2974' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc2974 + * Linear Technology LTC2977 + Prefix: 'ltc2977' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc2977 + * Linear Technology LTC2978, LTC2978A + Prefix: 'ltc2978' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc2978 + http://www.linear.com/product/ltc2978a + * Linear Technology LTC3880 + Prefix: 'ltc3880' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc3880 + * Linear Technology LTC3883 + Prefix: 'ltc3883' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc3883 + * Linear Technology LTM4676 + Prefix: 'ltm4676' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltm4676 + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply +monitor. LTC2977 is a pin compatible replacement for LTC2978. LTC3880 is a dual +output poly-phase step-down DC/DC controller. LTC3883 is a single phase +step-down DC/DC controller. LTM4676 is a dual 13A or single 26A uModule +regulator. + + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +Example: the following commands will load the driver for an LTC2978 at address +0x60 on I2C bus #1: + +# modprobe ltc2978 +# echo ltc2978 0x60 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs attributes +---------------- + +in1_label "vin" +in1_input Measured input voltage. +in1_min Minimum input voltage. +in1_max Maximum input voltage. + LTC2974, LTC2977, and LTC2978 only. +in1_lcrit Critical minimum input voltage. + LTC2974, LTC2977, and LTC2978 only. +in1_crit Critical maximum input voltage. +in1_min_alarm Input voltage low alarm. +in1_max_alarm Input voltage high alarm. + LTC2974, LTC2977, and LTC2978 only. +in1_lcrit_alarm Input voltage critical low alarm. + LTC2974, LTC2977, and LTC2978 only. +in1_crit_alarm Input voltage critical high alarm. +in1_lowest Lowest input voltage. + LTC2974, LTC2977, and LTC2978 only. +in1_highest Highest input voltage. +in1_reset_history Reset input voltage history. + +in[N]_label "vout[1-8]". + LTC2974: N=2-5 + LTC2977: N=2-9 + LTC2978: N=2-9 + LTC3880, LTM4676: N=2-3 + LTC3883: N=2 +in[N]_input Measured output voltage. +in[N]_min Minimum output voltage. +in[N]_max Maximum output voltage. +in[N]_lcrit Critical minimum output voltage. +in[N]_crit Critical maximum output voltage. +in[N]_min_alarm Output voltage low alarm. +in[N]_max_alarm Output voltage high alarm. +in[N]_lcrit_alarm Output voltage critical low alarm. +in[N]_crit_alarm Output voltage critical high alarm. +in[N]_lowest Lowest output voltage. LTC2974 and LTC2978 only. +in[N]_highest Highest output voltage. +in[N]_reset_history Reset output voltage history. + +temp[N]_input Measured temperature. + On LTC2974, temp[1-4] report external temperatures, + and temp5 reports the chip temperature. + On LTC2977 and LTC2978, only one temperature measurement + is supported and reports the chip temperature. + On LTC3880 and LTM4676, temp1 and temp2 report external + temperatures, and temp3 reports the chip temperature. + On LTC3883, temp1 reports an external temperature, + and temp2 reports the chip temperature. +temp[N]_min Mimimum temperature. LTC2974, LCT2977, and LTC2978 only. +temp[N]_max Maximum temperature. +temp[N]_lcrit Critical low temperature. +temp[N]_crit Critical high temperature. +temp[N]_min_alarm Temperature low alarm. + LTC2974, LTC2977, and LTC2978 only. +temp[N]_max_alarm Temperature high alarm. +temp[N]_lcrit_alarm Temperature critical low alarm. +temp[N]_crit_alarm Temperature critical high alarm. +temp[N]_lowest Lowest measured temperature. + LTC2974, LTC2977, and LTC2978 only. + Not supported for chip temperature sensor on LTC2974. +temp[N]_highest Highest measured temperature. Not supported for chip + temperature sensor on LTC2974. +temp[N]_reset_history Reset temperature history. Not supported for chip + temperature sensor on LTC2974. + +power1_label "pin". LTC3883 only. +power1_input Measured input power. + +power[N]_label "pout[1-4]". + LTC2974: N=1-4 + LTC2977: Not supported + LTC2978: Not supported + LTC3880, LTM4676: N=1-2 + LTC3883: N=2 +power[N]_input Measured output power. + +curr1_label "iin". LTC3880, LTC3883, and LTM4676 only. +curr1_input Measured input current. +curr1_max Maximum input current. +curr1_max_alarm Input current high alarm. +curr1_highest Highest input current. LTC3883 only. +curr1_reset_history Reset input current history. LTC3883 only. + +curr[N]_label "iout[1-4]". + LTC2974: N=1-4 + LTC2977: not supported + LTC2978: not supported + LTC3880, LTM4676: N=2-3 + LTC3883: N=2 +curr[N]_input Measured output current. +curr[N]_max Maximum output current. +curr[N]_crit Critical high output current. +curr[N]_lcrit Critical low output current. LTC2974 only. +curr[N]_max_alarm Output current high alarm. +curr[N]_crit_alarm Output current critical high alarm. +curr[N]_lcrit_alarm Output current critical low alarm. LTC2974 only. +curr[N]_lowest Lowest output current. LTC2974 only. +curr[N]_highest Highest output current. +curr[N]_reset_history Reset output current history. diff --git a/Documentation/hwmon/ltc4151 b/Documentation/hwmon/ltc4151 new file mode 100644 index 00000000000..43c667e6677 --- /dev/null +++ b/Documentation/hwmon/ltc4151 @@ -0,0 +1,47 @@ +Kernel driver ltc4151 +===================== + +Supported chips: + * Linear Technology LTC4151 + Prefix: 'ltc4151' + Addresses scanned: - + Datasheet: + http://www.linear.com/docs/Datasheet/4151fc.pdf + +Author: Per Dalen <per.dalen@appeartv.com> + + +Description +----------- + +The LTC4151 is a High Voltage I2C Current and Voltage Monitor. + + +Usage Notes +----------- + +This driver does not probe for LTC4151 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC4151 at address 0x6f +on I2C bus #0: +# modprobe ltc4151 +# echo ltc4151 0x6f > /sys/bus/i2c/devices/i2c-0/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADIN +and VIN registers. + +Current reading provided by this driver is reported as obtained from the Current +Sense register. The reported value assumes that a 1 mOhm sense resistor is +installed. + +in1_input VDIN voltage (mV) + +in2_input ADIN voltage (mV) + +curr1_input SENSE current (mA) diff --git a/Documentation/hwmon/ltc4215 b/Documentation/hwmon/ltc4215 new file mode 100644 index 00000000000..c196a184625 --- /dev/null +++ b/Documentation/hwmon/ltc4215 @@ -0,0 +1,51 @@ +Kernel driver ltc4215 +===================== + +Supported chips: + * Linear Technology LTC4215 + Prefix: 'ltc4215' + Addresses scanned: 0x44 + Datasheet: + http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1163,P17572,D12697 + +Author: Ira W. Snyder <iws@ovro.caltech.edu> + + +Description +----------- + +The LTC4215 controller allows a board to be safely inserted and removed +from a live backplane. + + +Usage Notes +----------- + +This driver does not probe for LTC4215 devices, due to the fact that some +of the possible addresses are unfriendly to probing. You will have to +instantiate the devices explicitly. + +Example: the following will load the driver for an LTC4215 at address 0x44 +on I2C bus #0: +$ modprobe ltc4215 +$ echo ltc4215 0x44 > /sys/bus/i2c/devices/i2c-0/new_device + + +Sysfs entries +------------- + +The LTC4215 has built-in limits for overvoltage, undervoltage, and +undercurrent warnings. This makes it very likely that the reference +circuit will be used. + +in1_input input voltage +in2_input output voltage + +in1_min_alarm input undervoltage alarm +in1_max_alarm input overvoltage alarm + +curr1_input current +curr1_max_alarm overcurrent alarm + +power1_input power usage +power1_alarm power bad alarm diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245 new file mode 100644 index 00000000000..b478b086496 --- /dev/null +++ b/Documentation/hwmon/ltc4245 @@ -0,0 +1,102 @@ +Kernel driver ltc4245 +===================== + +Supported chips: + * Linear Technology LTC4245 + Prefix: 'ltc4245' + Addresses scanned: 0x20-0x3f + Datasheet: + http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517 + +Author: Ira W. Snyder <iws@ovro.caltech.edu> + + +Description +----------- + +The LTC4245 controller allows a board to be safely inserted and removed +from a live backplane in multiple supply systems such as CompactPCI and +PCI Express. + + +Usage Notes +----------- + +This driver does not probe for LTC4245 devices, due to the fact that some +of the possible addresses are unfriendly to probing. You will have to +instantiate the devices explicitly. + +Example: the following will load the driver for an LTC4245 at address 0x23 +on I2C bus #1: +$ modprobe ltc4245 +$ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +The LTC4245 has built-in limits for over and under current warnings. This +makes it very likely that the reference circuit will be used. + +This driver uses the values in the datasheet to change the register values +into the values specified in the sysfs-interface document. The current readings +rely on the sense resistors listed in Table 2: "Sense Resistor Values". + +in1_input 12v input voltage (mV) +in2_input 5v input voltage (mV) +in3_input 3v input voltage (mV) +in4_input Vee (-12v) input voltage (mV) + +in1_min_alarm 12v input undervoltage alarm +in2_min_alarm 5v input undervoltage alarm +in3_min_alarm 3v input undervoltage alarm +in4_min_alarm Vee (-12v) input undervoltage alarm + +curr1_input 12v current (mA) +curr2_input 5v current (mA) +curr3_input 3v current (mA) +curr4_input Vee (-12v) current (mA) + +curr1_max_alarm 12v overcurrent alarm +curr2_max_alarm 5v overcurrent alarm +curr3_max_alarm 3v overcurrent alarm +curr4_max_alarm Vee (-12v) overcurrent alarm + +in5_input 12v output voltage (mV) +in6_input 5v output voltage (mV) +in7_input 3v output voltage (mV) +in8_input Vee (-12v) output voltage (mV) + +in5_min_alarm 12v output undervoltage alarm +in6_min_alarm 5v output undervoltage alarm +in7_min_alarm 3v output undervoltage alarm +in8_min_alarm Vee (-12v) output undervoltage alarm + +in9_input GPIO voltage data (see note 1) +in10_input GPIO voltage data (see note 1) +in11_input GPIO voltage data (see note 1) + +power1_input 12v power usage (mW) +power2_input 5v power usage (mW) +power3_input 3v power usage (mW) +power4_input Vee (-12v) power usage (mW) + + +Note 1 +------ + +If you have NOT configured the driver to sample all GPIO pins as analog +voltages, then the in10_input and in11_input sysfs attributes will not be +created. The driver will sample the GPIO pin that is currently connected to the +ADC as an analog voltage, and report the value in in9_input. + +If you have configured the driver to sample all GPIO pins as analog voltages, +then they will be sampled in round-robin fashion. If userspace reads too +slowly, -EAGAIN will be returned when you read the sysfs attribute containing +the sensor reading. + +The LTC4245 chip can be configured to sample all GPIO pins with two methods: +1) platform data -- see include/linux/i2c/ltc4245.h +2) OF device tree -- add the "ltc4245,use-extra-gpios" property to each chip + +The default mode of operation is to sample a single GPIO pin. diff --git a/Documentation/hwmon/ltc4260 b/Documentation/hwmon/ltc4260 new file mode 100644 index 00000000000..c4ff4ad998b --- /dev/null +++ b/Documentation/hwmon/ltc4260 @@ -0,0 +1,56 @@ +Kernel driver ltc4260 +===================== + +Supported chips: + * Linear Technology LTC4260 + Prefix: 'ltc4260' + Addresses scanned: - + Datasheet: + http://cds.linear.com/docs/en/datasheet/4260fc.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +The LTC4260 Hot Swap controller allows a board to be safely inserted +and removed from a live backplane. + + +Usage Notes +----------- + +This driver does not probe for LTC4260 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC4260 at address 0x10 +on I2C bus #1: +$ modprobe ltc4260 +$ echo ltc4260 0x10 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADC +registers. If a set of voltage divider resistors is installed, calculate the +real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the +value of the divider resistor against the measured voltage and R2 is the value +of the divider resistor against Ground. + +Current reading provided by this driver is reported as obtained from the ADC +Current Sense register. The reported value assumes that a 1 mOhm sense resistor +is installed. If a different sense resistor is installed, calculate the real +current by dividing the reported value by the sense resistor value in mOhm. + +in1_input SOURCE voltage (mV) +in1_min_alarm Undervoltage alarm +in1_max_alarm Overvoltage alarm + +in2_input ADIN voltage (mV) +in2_alarm Power bad alarm + +curr1_input SENSE current (mA) +curr1_alarm SENSE overcurrent alarm diff --git a/Documentation/hwmon/ltc4261 b/Documentation/hwmon/ltc4261 new file mode 100644 index 00000000000..9378a75c613 --- /dev/null +++ b/Documentation/hwmon/ltc4261 @@ -0,0 +1,63 @@ +Kernel driver ltc4261 +===================== + +Supported chips: + * Linear Technology LTC4261 + Prefix: 'ltc4261' + Addresses scanned: - + Datasheet: + http://cds.linear.com/docs/Datasheet/42612fb.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +The LTC4261/LTC4261-2 negative voltage Hot Swap controllers allow a board +to be safely inserted and removed from a live backplane. + + +Usage Notes +----------- + +This driver does not probe for LTC4261 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC4261 at address 0x10 +on I2C bus #1: +$ modprobe ltc4261 +$ echo ltc4261 0x10 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADC +registers. If a set of voltage divider resistors is installed, calculate the +real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the +value of the divider resistor against the measured voltage and R2 is the value +of the divider resistor against Ground. + +Current reading provided by this driver is reported as obtained from the ADC +Current Sense register. The reported value assumes that a 1 mOhm sense resistor +is installed. If a different sense resistor is installed, calculate the real +current by dividing the reported value by the sense resistor value in mOhm. + +The chip has two voltage sensors, but only one set of voltage alarm status bits. +In many many designs, those alarms are associated with the ADIN2 sensor, due to +the proximity of the ADIN2 pin to the OV pin. ADIN2 is, however, not available +on all chip variants. To ensure that the alarm condition is reported to the user, +report it with both voltage sensors. + +in1_input ADIN2 voltage (mV) +in1_min_alarm ADIN/ADIN2 Undervoltage alarm +in1_max_alarm ADIN/ADIN2 Overvoltage alarm + +in2_input ADIN voltage (mV) +in2_min_alarm ADIN/ADIN2 Undervoltage alarm +in2_max_alarm ADIN/ADIN2 Overvoltage alarm + +curr1_input SENSE current (mA) +curr1_alarm SENSE overcurrent alarm diff --git a/Documentation/hwmon/max16064 b/Documentation/hwmon/max16064 new file mode 100644 index 00000000000..d59cc7829be --- /dev/null +++ b/Documentation/hwmon/max16064 @@ -0,0 +1,66 @@ +Kernel driver max16064 +====================== + +Supported chips: + * Maxim MAX16064 + Prefix: 'max16064' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX16064 Quad Power-Supply +Controller with Active-Voltage Output Control and PMBus Interface. + +The driver is a client driver to the core PMBus driver. +Please see Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-4]_label "vout[1-4]" +in[1-4]_input Measured voltage. From READ_VOUT register. +in[1-4]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-4]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-4]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-4]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-4]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-4]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-4]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-4]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. +in[1-4]_highest Historical maximum voltage. +in[1-4]_reset_history Write any value to reset history. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. +temp1_highest Historical maximum temperature. +temp1_reset_history Write any value to reset history. diff --git a/Documentation/hwmon/max16065 b/Documentation/hwmon/max16065 new file mode 100644 index 00000000000..208a29e4301 --- /dev/null +++ b/Documentation/hwmon/max16065 @@ -0,0 +1,105 @@ +Kernel driver max16065 +====================== + +Supported chips: + * Maxim MAX16065, MAX16066 + Prefixes: 'max16065', 'max16066' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16065-MAX16066.pdf + * Maxim MAX16067 + Prefix: 'max16067' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16067.pdf + * Maxim MAX16068 + Prefix: 'max16068' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16068.pdf + * Maxim MAX16070/MAX16071 + Prefixes: 'max16070', 'max16071' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16070-MAX16071.pdf + + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +[From datasheets] The MAX16065/MAX16066 flash-configurable system managers +monitor and sequence multiple system voltages. The MAX16065/MAX16066 can also +accurately monitor (+/-2.5%) one current channel using a dedicated high-side +current-sense amplifier. The MAX16065 manages up to twelve system voltages +simultaneously, and the MAX16066 manages up to eight supply voltages. + +The MAX16067 flash-configurable system manager monitors and sequences multiple +system voltages. The MAX16067 manages up to six system voltages simultaneously. + +The MAX16068 flash-configurable system manager monitors and manages up to six +system voltages simultaneously. + +The MAX16070/MAX16071 flash-configurable system monitors supervise multiple +system voltages. The MAX16070/MAX16071 can also accurately monitor (+/-2.5%) +one current channel using a dedicated high-side current-sense amplifier. The +MAX16070 monitors up to twelve system voltages simultaneously, and the MAX16071 +monitors up to eight supply voltages. + +Each monitored channel has its own low and high critical limits. MAX16065, +MAX16066, MAX16070, and MAX16071 support an additional limit which is +configurable as either low or high secondary limit. MAX16065, MAX16066, +MAX16070, and MAX16071 also support supply current monitoring. + + +Usage Notes +----------- + +This driver does not probe for devices, since there is no register which +can be safely used to identify the chip. You will have to instantiate +the devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + +WARNING: Do not access chip registers using the i2cdump command, and do not use +any of the i2ctools commands on a command register (0xa5 to 0xac). The chips +supported by this driver interpret any access to a command register (including +read commands) as request to execute the command in question. This may result in +power loss, board resets, and/or Flash corruption. Worst case, your board may +turn into a brick. + + +Sysfs entries +------------- + +in[0-11]_input Input voltage measurements. + +in12_input Voltage on CSP (Current Sense Positive) pin. + Only if the chip supports current sensing and if + current sensing is enabled. + +in[0-11]_min Low warning limit. + Supported on MAX16065, MAX16066, MAX16070, and MAX16071 + only. + +in[0-11]_max High warning limit. + Supported on MAX16065, MAX16066, MAX16070, and MAX16071 + only. + + Either low or high warning limits are supported + (depending on chip configuration), but not both. + +in[0-11]_lcrit Low critical limit. + +in[0-11]_crit High critical limit. + +in[0-11]_alarm Input voltage alarm. + +curr1_input Current sense input; only if the chip supports current + sensing and if current sensing is enabled. + Displayed current assumes 0.001 Ohm current sense + resistor. + +curr1_alarm Overcurrent alarm; only if the chip supports current + sensing and if current sensing is enabled. diff --git a/Documentation/hwmon/max1619 b/Documentation/hwmon/max1619 index d6f8d9cd7d7..518bae3a80c 100644 --- a/Documentation/hwmon/max1619 +++ b/Documentation/hwmon/max1619 @@ -9,8 +9,8 @@ Supported chips: http://pdfserv.maxim-ic.com/en/ds/MAX1619.pdf Authors: - Alexey Fisher <fishor@mail.ru>, - Jean Delvare <khali@linux-fr.org> + Oleksij Rempel <bug-track@fisher-privat.net>, + Jean Delvare <jdelvare@suse.de> Description ----------- diff --git a/Documentation/hwmon/max1668 b/Documentation/hwmon/max1668 new file mode 100644 index 00000000000..0616ed9758d --- /dev/null +++ b/Documentation/hwmon/max1668 @@ -0,0 +1,60 @@ +Kernel driver max1668 +===================== + +Supported chips: + * Maxim MAX1668, MAX1805 and MAX1989 + Prefix: 'max1668' + Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX1668-MAX1989.pdf + +Author: + David George <david.george@ska.ac.za> + +Description +----------- + +This driver implements support for the Maxim MAX1668, MAX1805 and MAX1989 +chips. + +The three devices are very similar, but the MAX1805 has a reduced feature +set; only two remote temperature inputs vs the four avaible on the other +two ICs. + +The driver is able to distinguish between the devices and creates sysfs +entries as follows: + +MAX1805, MAX1668 and MAX1989: + +temp1_input ro local (ambient) temperature +temp1_max rw local temperature maximum threshold for alarm +temp1_max_alarm ro local temperature maximum threshold alarm +temp1_min rw local temperature minimum threshold for alarm +temp1_min_alarm ro local temperature minimum threshold alarm +temp2_input ro remote temperature 1 +temp2_max rw remote temperature 1 maximum threshold for alarm +temp2_max_alarm ro remote temperature 1 maximum threshold alarm +temp2_min rw remote temperature 1 minimum threshold for alarm +temp2_min_alarm ro remote temperature 1 minimum threshold alarm +temp3_input ro remote temperature 2 +temp3_max rw remote temperature 2 maximum threshold for alarm +temp3_max_alarm ro remote temperature 2 maximum threshold alarm +temp3_min rw remote temperature 2 minimum threshold for alarm +temp3_min_alarm ro remote temperature 2 minimum threshold alarm + +MAX1668 and MAX1989 only: +temp4_input ro remote temperature 3 +temp4_max rw remote temperature 3 maximum threshold for alarm +temp4_max_alarm ro remote temperature 3 maximum threshold alarm +temp4_min rw remote temperature 3 minimum threshold for alarm +temp4_min_alarm ro remote temperature 3 minimum threshold alarm +temp5_input ro remote temperature 4 +temp5_max rw remote temperature 4 maximum threshold for alarm +temp5_max_alarm ro remote temperature 4 maximum threshold alarm +temp5_min rw remote temperature 4 minimum threshold for alarm +temp5_min_alarm ro remote temperature 4 minimum threshold alarm + +Module Parameters +----------------- + +* read_only: int + Set to non-zero if you wish to prevent write access to alarm thresholds. diff --git a/Documentation/hwmon/max197 b/Documentation/hwmon/max197 new file mode 100644 index 00000000000..8d89b9009df --- /dev/null +++ b/Documentation/hwmon/max197 @@ -0,0 +1,60 @@ +Maxim MAX197 driver +=================== + +Author: + * Vivien Didelot <vivien.didelot@savoirfairelinux.com> + +Supported chips: + * Maxim MAX197 + Prefix: 'max197' + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX197.pdf + + * Maxim MAX199 + Prefix: 'max199' + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX199.pdf + +Description +----------- + +The A/D converters MAX197, and MAX199 are both 8-Channel, Multi-Range, 5V, +12-Bit DAS with 8+4 Bus Interface and Fault Protection. + +The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to 10V, +while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199. + +Platform data +------------- + +The MAX197 platform data (defined in linux/platform_data/max197.h) should be +filled with a pointer to a conversion function, defined like: + + int convert(u8 ctrl); + +ctrl is the control byte to write to start a new conversion. +On success, the function must return the 12-bit raw value read from the chip, +or a negative error code otherwise. + +Control byte format: + +Bit Name Description +7,6 PD1,PD0 Clock and Power-Down modes +5 ACQMOD Internal or External Controlled Acquisition +4 RNG Full-scale voltage magnitude at the input +3 BIP Unipolar or Bipolar conversion mode +2,1,0 A2,A1,A0 Channel + +Sysfs interface +--------------- + +* in[0-7]_input: The conversion value for the corresponding channel. + RO + +* in[0-7]_min: The lower limit (in mV) for the corresponding channel. + For the MAX197, it will be adjusted to -10000, -5000, or 0. + For the MAX199, it will be adjusted to -4000, -2000, or 0. + RW + +* in[0-7]_max: The higher limit (in mV) for the corresponding channel. + For the MAX197, it will be adjusted to 0, 5000, or 10000. + For the MAX199, it will be adjusted to 0, 2000, or 4000. + RW diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 new file mode 100644 index 00000000000..37cbf472a19 --- /dev/null +++ b/Documentation/hwmon/max34440 @@ -0,0 +1,127 @@ +Kernel driver max34440 +====================== + +Supported chips: + * Maxim MAX34440 + Prefixes: 'max34440' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf + * Maxim MAX34441 + PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller + Prefixes: 'max34441' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf + * Maxim MAX34446 + PMBus Power-Supply Data Logger + Prefixes: 'max34446' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34446.pdf + * Maxim MAX34460 + PMBus 12-Channel Voltage Monitor & Sequencer + Prefix: 'max34460' + Addresses scanned: - + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX34460.pdf + * Maxim MAX34461 + PMBus 16-Channel Voltage Monitor & Sequencer + Prefix: 'max34461' + Addresses scanned: - + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX34461.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX34440 PMBus 6-Channel +Power-Supply Manager, MAX34441 PMBus 5-Channel Power-Supply Manager +and Intelligent Fan Controller, and MAX34446 PMBus Power-Supply Data Logger. +It also supports the MAX34460 and MAX34461 PMBus Voltage Monitor & Sequencers. +The MAX34460 supports 12 voltage channels, and the MAX34461 supports 16 voltage +channels. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + +For MAX34446, the value of the currX_crit attribute determines if current or +voltage measurement is enabled for a given channel. Voltage measurement is +enabled if currX_crit is set to 0; current measurement is enabled if the +attribute is set to a positive value. Power measurement is only enabled if +channel 1 (3) is configured for voltage measurement, and channel 2 (4) is +configured for current measurement. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-6]_label "vout[1-6]". +in[1-6]_input Measured voltage. From READ_VOUT register. +in[1-6]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-6]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-6]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-6]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-6]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-6]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-6]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-6]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. +in[1-6]_lowest Historical minimum voltage. +in[1-6]_highest Historical maximum voltage. +in[1-6]_reset_history Write any value to reset history. + + MAX34446 only supports in[1-4]. + +curr[1-6]_label "iout[1-6]". +curr[1-6]_input Measured current. From READ_IOUT register. +curr[1-6]_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr[1-6]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr[1-6]_max_alarm Current high alarm. From IOUT_OC_WARNING status. +curr[1-6]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. +curr[1-4]_average Historical average current (MAX34446 only). +curr[1-6]_highest Historical maximum current. +curr[1-6]_reset_history Write any value to reset history. + + in6 and curr6 attributes only exist for MAX34440. + MAX34446 only supports curr[1-4]. + +power[1,3]_label "pout[1,3]" +power[1,3]_input Measured power. +power[1,3]_average Historical average power. +power[1,3]_highest Historical maximum power. + + Power attributes only exist for MAX34446. + +temp[1-8]_input Measured temperatures. From READ_TEMPERATURE_1 register. + temp1 is the chip's internal temperature. temp2..temp5 + are remote I2C temperature sensors. For MAX34441, temp6 + is a remote thermal-diode sensor. For MAX34440, temp6..8 + are remote I2C temperature sensors. +temp[1-8]_max Maximum temperature. From OT_WARN_LIMIT register. +temp[1-8]_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp[1-8]_max_alarm Temperature high alarm. +temp[1-8]_crit_alarm Temperature critical high alarm. +temp[1-8]_average Historical average temperature (MAX34446 only). +temp[1-8]_highest Historical maximum temperature. +temp[1-8]_reset_history Write any value to reset history. + + temp7 and temp8 attributes only exist for MAX34440. + MAX34446 only supports temp[1-3]. + +MAX34460 supports attribute groups in[1-12] and temp[1-5]. +MAX34461 supports attribute groups in[1-16] and temp[1-5]. diff --git a/Documentation/hwmon/max6639 b/Documentation/hwmon/max6639 new file mode 100644 index 00000000000..dc49f8be716 --- /dev/null +++ b/Documentation/hwmon/max6639 @@ -0,0 +1,49 @@ +Kernel driver max6639 +===================== + +Supported chips: + * Maxim MAX6639 + Prefix: 'max6639' + Addresses scanned: I2C 0x2c, 0x2e, 0x2f + Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6639.pdf + +Authors: + He Changqing <hechangqing@semptian.com> + Roland Stigge <stigge@antcom.de> + +Description +----------- + +This driver implements support for the Maxim MAX6639. This chip is a 2-channel +temperature monitor with dual PWM fan speed controller. It can monitor its own +temperature and one external diode-connected transistor or two external +diode-connected transistors. + +The following device attributes are implemented via sysfs: + +Attribute R/W Contents +---------------------------------------------------------------------------- +temp1_input R Temperature channel 1 input (0..150 C) +temp2_input R Temperature channel 2 input (0..150 C) +temp1_fault R Temperature channel 1 diode fault +temp2_fault R Temperature channel 2 diode fault +temp1_max RW Set THERM temperature for input 1 + (in C, see datasheet) +temp2_max RW Set THERM temperature for input 2 +temp1_crit RW Set ALERT temperature for input 1 +temp2_crit RW Set ALERT temperature for input 2 +temp1_emergency RW Set OT temperature for input 1 + (in C, see datasheet) +temp2_emergency RW Set OT temperature for input 2 +pwm1 RW Fan 1 target duty cycle (0..255) +pwm2 RW Fan 2 target duty cycle (0..255) +fan1_input R TACH1 fan tachometer input (in RPM) +fan2_input R TACH2 fan tachometer input (in RPM) +fan1_fault R Fan 1 fault +fan2_fault R Fan 2 fault +temp1_max_alarm R Alarm on THERM temperature on channel 1 +temp2_max_alarm R Alarm on THERM temperature on channel 2 +temp1_crit_alarm R Alarm on ALERT temperature on channel 1 +temp2_crit_alarm R Alarm on ALERT temperature on channel 2 +temp1_emergency_alarm R Alarm on OT temperature on channel 1 +temp2_emergency_alarm R Alarm on OT temperature on channel 2 diff --git a/Documentation/hwmon/max6642 b/Documentation/hwmon/max6642 new file mode 100644 index 00000000000..afbd3e4942e --- /dev/null +++ b/Documentation/hwmon/max6642 @@ -0,0 +1,21 @@ +Kernel driver max6642 +===================== + +Supported chips: + * Maxim MAX6642 + Prefix: 'max6642' + Addresses scanned: I2C 0x48-0x4f + Datasheet: Publicly available at the Maxim website + http://datasheets.maxim-ic.com/en/ds/MAX6642.pdf + +Authors: + Per Dalen <per.dalen@appeartv.com> + +Description +----------- + +The MAX6642 is a digital temperature sensor. It senses its own temperature as +well as the temperature on one external diode. + +All temperature values are given in degrees Celsius. Resolution +is 0.25 degree for the local temperature and for the remote temperature. diff --git a/Documentation/hwmon/max6650 b/Documentation/hwmon/max6650 new file mode 100644 index 00000000000..58d9644a2bd --- /dev/null +++ b/Documentation/hwmon/max6650 @@ -0,0 +1,64 @@ +Kernel driver max6650 +===================== + +Supported chips: + * Maxim MAX6650 + Prefix: 'max6650' + Addresses scanned: none + Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf + * Maxim MAX6651 + Prefix: 'max6651' + Addresses scanned: none + Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf + +Authors: + Hans J. Koch <hjk@hansjkoch.de> + John Morris <john.morris@spirentcom.com> + Claus Gindhart <claus.gindhart@kontron.com> + +Description +----------- + +This driver implements support for the Maxim MAX6650 and MAX6651. + +The 2 devices are very similar, but the MAX6550 has a reduced feature +set, e.g. only one fan-input, instead of 4 for the MAX6651. + +The driver is not able to distinguish between the 2 devices. + +The driver provides the following sensor accesses in sysfs: + +fan1_input ro fan tachometer speed in RPM +fan2_input ro " +fan3_input ro " +fan4_input ro " +fan1_target rw desired fan speed in RPM (closed loop mode only) +pwm1_enable rw regulator mode, 0=full on, 1=open loop, 2=closed loop +pwm1 rw relative speed (0-255), 255=max. speed. + Used in open loop mode only. +fan1_div rw sets the speed range the inputs can handle. Legal + values are 1, 2, 4, and 8. Use lower values for + faster fans. + +Usage notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + +Module parameters +----------------- + +If your board has a BIOS that initializes the MAX6650/6651 correctly, you can +simply load your module without parameters. It won't touch the configuration +registers then. If your board BIOS doesn't initialize the chip, or you want +different settings, you can set the following parameters: + +voltage_12V: 5=5V fan, 12=12V fan, 0=don't change +prescaler: Possible values are 1,2,4,8,16, or 0 for don't change +clock: The clock frequency in Hz of the chip the driver should assume [254000] + +Please have a look at the MAX6650/6651 data sheet and make sure that you fully +understand the meaning of these parameters before you attempt to change them. + diff --git a/Documentation/hwmon/max6697 b/Documentation/hwmon/max6697 new file mode 100644 index 00000000000..6594177eded --- /dev/null +++ b/Documentation/hwmon/max6697 @@ -0,0 +1,58 @@ +Kernel driver max6697 +===================== + +Supported chips: + * Maxim MAX6581 + Prefix: 'max6581' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6581.pdf + * Maxim MAX6602 + Prefix: 'max6602' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6602.pdf + * Maxim MAX6622 + Prefix: 'max6622' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6622.pdf + * Maxim MAX6636 + Prefix: 'max6636' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6636.pdf + * Maxim MAX6689 + Prefix: 'max6689' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6689.pdf + * Maxim MAX6693 + Prefix: 'max6693' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6693.pdf + * Maxim MAX6694 + Prefix: 'max6694' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6694.pdf + * Maxim MAX6697 + Prefix: 'max6697' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6697.pdf + * Maxim MAX6698 + Prefix: 'max6698' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6698.pdf + * Maxim MAX6699 + Prefix: 'max6699' + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX6699.pdf + +Author: + Guenter Roeck <linux@roeck-us.net> + +Description +----------- + +This driver implements support for several MAX6697 compatible temperature sensor +chips. The chips support one local temperature sensor plus four, six, or seven +remote temperature sensors. Remote temperature sensors are diode-connected +thermal transitors, except for MAX6698 which supports three diode-connected +thermal transistors plus three thermistors in addition to the local temperature +sensor. + +The driver provides the following sysfs attributes. temp1 is the local (chip) +temperature, temp[2..n] are remote temperatures. The actually supported +per-channel attributes are chip type and channel dependent. + +tempX_input RO temperature +tempX_max RW temperature maximum threshold +tempX_max_alarm RO temperature maximum threshold alarm +tempX_crit RW temperature critical threshold +tempX_crit_alarm RO temperature critical threshold alarm +tempX_fault RO temperature diode fault (remote sensors only) diff --git a/Documentation/hwmon/max8688 b/Documentation/hwmon/max8688 new file mode 100644 index 00000000000..e78078638b9 --- /dev/null +++ b/Documentation/hwmon/max8688 @@ -0,0 +1,75 @@ +Kernel driver max8688 +===================== + +Supported chips: + * Maxim MAX8688 + Prefix: 'max8688' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX8688 Digital Power-Supply +Controller/Monitor with PMBus Interface. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vout1" +in1_input Measured voltage. From READ_VOUT register. +in1_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register. +in1_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in1_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register. +in1_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in1_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in1_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. +in1_highest Historical maximum voltage. +in1_reset_history Write any value to reset history. + +curr1_label "iout1" +curr1_input Measured current. From READ_IOUT register. +curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr1_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. +curr1_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. +curr1_highest Historical maximum current. +curr1_reset_history Write any value to reset history. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. +temp1_highest Historical maximum temperature. +temp1_reset_history Write any value to reset history. diff --git a/Documentation/hwmon/mc13783-adc b/Documentation/hwmon/mc13783-adc new file mode 100644 index 00000000000..d0e7b3fa9e7 --- /dev/null +++ b/Documentation/hwmon/mc13783-adc @@ -0,0 +1,74 @@ +Kernel driver mc13783-adc +========================= + +Supported chips: + * Freescale Atlas MC13783 + Prefix: 'mc13783' + Datasheet: http://www.freescale.com/files/rf_if/doc/data_sheet/MC13783.pdf?fsrch=1 + * Freescale Atlas MC13892 + Prefix: 'mc13892' + Datasheet: http://cache.freescale.com/files/analog/doc/data_sheet/MC13892.pdf?fsrch=1&sr=1 + +Authors: + Sascha Hauer <s.hauer@pengutronix.de> + Luotao Fu <l.fu@pengutronix.de> + +Description +----------- + +The Freescale MC13783 and MC13892 are Power Management and Audio Circuits. +Among other things they contain a 10-bit A/D converter. The converter has 16 +(MC13783) resp. 12 (MC13892) channels which can be used in different modes. The +A/D converter has a resolution of 2.25mV. + +Some channels can be used as General Purpose inputs or in a dedicated mode with +a chip internal scaling applied . + +Currently the driver only supports the Application Supply channel (BP / BPSNS), +the General Purpose inputs and touchscreen. + +See the following tables for the meaning of the different channels and their +chip internal scaling: + +MC13783: +Channel Signal Input Range Scaling +------------------------------------------------------------------------------- +0 Battery Voltage (BATT) 2.50 - 4.65V -2.40V +1 Battery Current (BATT - BATTISNS) -50 - 50 mV x20 +2 Application Supply (BP) 2.50 - 4.65V -2.40V +3 Charger Voltage (CHRGRAW) 0 - 10V / /5 + 0 - 20V /10 +4 Charger Current (CHRGISNSP-CHRGISNSN) -0.25 - 0.25V x4 +5 General Purpose ADIN5 / Battery Pack Thermistor 0 - 2.30V No +6 General Purpose ADIN6 / Backup Voltage (LICELL) 0 - 2.30V / No / + 1.50 - 3.50V -1.20V +7 General Purpose ADIN7 / UID / Die Temperature 0 - 2.30V / No / + 0 - 2.55V / x0.9 / No +8 General Purpose ADIN8 0 - 2.30V No +9 General Purpose ADIN9 0 - 2.30V No +10 General Purpose ADIN10 0 - 2.30V No +11 General Purpose ADIN11 0 - 2.30V No +12 General Purpose TSX1 / Touchscreen X-plate 1 0 - 2.30V No +13 General Purpose TSX2 / Touchscreen X-plate 2 0 - 2.30V No +14 General Purpose TSY1 / Touchscreen Y-plate 1 0 - 2.30V No +15 General Purpose TSY2 / Touchscreen Y-plate 2 0 - 2.30V No + +MC13892: +Channel Signal Input Range Scaling +------------------------------------------------------------------------------- +0 Battery Voltage (BATT) 0 - 4.8V /2 +1 Battery Current (BATT - BATTISNSCC) -60 - 60 mV x20 +2 Application Supply (BPSNS) 0 - 4.8V /2 +3 Charger Voltage (CHRGRAW) 0 - 12V / /5 + 0 - 20V /10 +4 Charger Current (CHRGISNS-BPSNS) / -0.3 - 0.3V / x4 / + Touchscreen X-plate 1 0 - 2.4V No +5 General Purpose ADIN5 / Battery Pack Thermistor 0 - 2.4V No +6 General Purpose ADIN6 / Backup Voltage (LICELL) 0 - 2.4V / No + Backup Voltage (LICELL) 0 - 3.6V x2/3 +7 General Purpose ADIN7 / UID / Die Temperature 0 - 2.4V / No / + 0 - 4.8V /2 +12 General Purpose TSX1 / Touchscreen X-plate 1 0 - 2.4V No +13 General Purpose TSX2 / Touchscreen X-plate 2 0 - 2.4V No +14 General Purpose TSY1 / Touchscreen Y-plate 1 0 - 2.4V No +15 General Purpose TSY2 / Touchscreen Y-plate 2 0 - 2.4V No diff --git a/Documentation/hwmon/mcp3021 b/Documentation/hwmon/mcp3021 new file mode 100644 index 00000000000..74a6b72adf5 --- /dev/null +++ b/Documentation/hwmon/mcp3021 @@ -0,0 +1,29 @@ +Kernel driver MCP3021 +====================== + +Supported chips: + * Microchip Technology MCP3021 + Prefix: 'mcp3021' + Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/21805a.pdf + * Microchip Technology MCP3221 + Prefix: 'mcp3221' + Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/21732c.pdf + +Authors: + Mingkai Hu + Sven Schuchmann <schuchmann@schleissheimer.de> + +Description +----------- + +This driver implements support for the Microchip Technology MCP3021 and +MCP3221 chip. + +The Microchip Technology Inc. MCP3021 is a successive approximation A/D +converter (ADC) with 10-bit resolution. The MCP3221 has 12-bit resolution. + +These devices provide one single-ended input with very low power consumption. +Communication to the MCP3021/MCP3221 is performed using a 2-wire I2C +compatible interface. Standard (100 kHz) and Fast (400 kHz) I2C modes are +available. The default I2C device address is 0x4d (contact the Microchip +factory for additional address options). diff --git a/Documentation/hwmon/nct6683 b/Documentation/hwmon/nct6683 new file mode 100644 index 00000000000..c1301d4300c --- /dev/null +++ b/Documentation/hwmon/nct6683 @@ -0,0 +1,57 @@ +Kernel driver nct6683 +===================== + +Supported chips: + * Nuvoton NCT6683D + Prefix: 'nct6683' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + +Authors: + Guenter Roeck <linux@roeck-us.net> + +Description +----------- + +This driver implements support for the Nuvoton NCT6683D eSIO chip. + +The chips implement up to shared 32 temperature and voltage sensors. +It supports up to 16 fan rotation sensors and up to 8 fan control engines. + +Temperatures are measured in degrees Celsius. Measurement resolution is +0.5 degrees C. + +Voltage sensors (also known as IN sensors) report their values in millivolts. + +Fan rotation speeds are reported in RPM (rotations per minute). + +Usage Note +---------- + +Limit register locations on Intel boards with EC firmware version 1.0 +build date 04/03/13 do not match the register locations in the Nuvoton +datasheet. Nuvoton confirms that Intel uses a special firmware version +with different register addresses. The specification describing the Intel +firmware is held under NDA by Nuvoton and Intel and not available +to the public. + +Some of the register locations can be reverse engineered; others are too +well hidden. Given this, writing any values from the operating system is +considered too risky with this firmware and has been disabled. All limits +must all be written from the BIOS. + +The driver has only been tested with the Intel firmware, and by default +only instantiates on Intel boards. To enable it on non-Intel boards, +set the 'force' module parameter to 1. + +Tested Boards and Firmware Versions +----------------------------------- + +The driver has been reported to work with the following boards and +firmware versions. + +Board Firmware version +--------------------------------------------------------------- +Intel DH87RL NCT6683D EC firmware version 1.0 build 04/03/13 +Intel DH87MC NCT6683D EC firmware version 1.0 build 04/03/13 +Intel DB85FL NCT6683D EC firmware version 1.0 build 04/03/13 diff --git a/Documentation/hwmon/nct6775 b/Documentation/hwmon/nct6775 new file mode 100644 index 00000000000..4e9ef60e8c6 --- /dev/null +++ b/Documentation/hwmon/nct6775 @@ -0,0 +1,188 @@ +Note +==== + +This driver supersedes the NCT6775F and NCT6776F support in the W83627EHF +driver. + +Kernel driver NCT6775 +===================== + +Supported chips: + * Nuvoton NCT5572D/NCT6771F/NCT6772F/NCT6775F/W83677HG-I + Prefix: 'nct6775' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT5577D/NCT6776D/NCT6776F + Prefix: 'nct6776' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT5532D/NCT6779D + Prefix: 'nct6779' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + +Authors: + Guenter Roeck <linux@roeck-us.net> + +Description +----------- + +This driver implements support for the Nuvoton NCT6775F, NCT6776F, and NCT6779D +and compatible super I/O chips. + +The chips support up to 25 temperature monitoring sources. Up to 6 of those are +direct temperature sensor inputs, the others are special sources such as PECI, +PCH, and SMBUS. Depending on the chip type, 2 to 6 of the temperature sources +can be monitored and compared against minimum, maximum, and critical +temperatures. The driver reports up to 10 of the temperatures to the user. +There are 4 to 5 fan rotation speed sensors, 8 to 15 analog voltage sensors, +one VID, alarms with beep warnings (control unimplemented), and some automatic +fan regulation strategies (plus manual fan control mode). + +The temperature sensor sources on all chips are configurable. The configured +source for each of the temperature sensors is provided in tempX_label. + +Temperatures are measured in degrees Celsius and measurement resolution is +either 1 degC or 0.5 degC, depending on the temperature source and +configuration. An alarm is triggered when the temperature gets higher than +the high limit; it stays on until the temperature falls below the hysteresis +value. Alarms are only supported for temp1 to temp6, depending on the chip type. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. On +NCT6775F, fan readings can be divided by a programmable divider (1, 2, 4, 8, +16, 32, 64 or 128) to give the readings more range or accuracy; the other chips +do not have a fan speed divider. The driver sets the most suitable fan divisor +itself; specifically, it increases the divider value each time a fan speed +reading returns an invalid value, and it reduces it if the fan speed reading +is lower than optimal. Some fans might not be present because they share pins +with other functions. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +The driver supports automatic fan control mode known as Thermal Cruise. +In this mode, the chip attempts to keep the measured temperature in a +predefined temperature range. If the temperature goes out of range, fan +is driven slower/faster to reach the predefined range again. + +The mode works for fan1-fan5. + +sysfs attributes +---------------- + +pwm[1-5] - this file stores PWM duty cycle or DC value (fan speed) in range: + 0 (lowest speed) to 255 (full) + +pwm[1-5]_enable - this file controls mode of fan/temperature control: + * 0 Fan control disabled (fans set to maximum speed) + * 1 Manual mode, write to pwm[0-5] any value 0-255 + * 2 "Thermal Cruise" mode + * 3 "Fan Speed Cruise" mode + * 4 "Smart Fan III" mode (NCT6775F only) + * 5 "Smart Fan IV" mode + +pwm[1-5]_mode - controls if output is PWM or DC level + * 0 DC output + * 1 PWM output + +Common fan control attributes +----------------------------- + +pwm[1-5]_temp_sel Temperature source. Value is temperature sensor index. + For example, select '1' for temp1_input. +pwm[1-5]_weight_temp_sel + Secondary temperature source. Value is temperature + sensor index. For example, select '1' for temp1_input. + Set to 0 to disable secondary temperature control. + +If secondary temperature functionality is enabled, it is controlled with the +following attributes. + +pwm[1-5]_weight_duty_step + Duty step size. +pwm[1-5]_weight_temp_step + Temperature step size. With each step over + temp_step_base, the value of weight_duty_step is added + to the current pwm value. +pwm[1-5]_weight_temp_step_base + Temperature at which secondary temperature control kicks + in. +pwm[1-5]_weight_temp_step_tol + Temperature step tolerance. + +Thermal Cruise mode (2) +----------------------- + +If the temperature is in the range defined by: + +pwm[1-5]_target_temp Target temperature, unit millidegree Celsius + (range 0 - 127000) +pwm[1-5]_temp_tolerance + Target temperature tolerance, unit millidegree Celsius + +there are no changes to fan speed. Once the temperature leaves the interval, fan +speed increases (if temperature is higher that desired) or decreases (if +temperature is lower than desired), using the following limits and time +intervals. + +pwm[1-5]_start fan pwm start value (range 1 - 255), to start fan + when the temperature is above defined range. +pwm[1-5]_floor lowest fan pwm (range 0 - 255) if temperature is below + the defined range. If set to 0, the fan is expected to + stop if the temperature is below the defined range. +pwm[1-5]_step_up_time milliseconds before fan speed is increased +pwm[1-5]_step_down_time milliseconds before fan speed is decreased +pwm[1-5]_stop_time how many milliseconds must elapse to switch + corresponding fan off (when the temperature was below + defined range). + +Speed Cruise mode (3) +--------------------- + +This modes tries to keep the fan speed constant. + +fan[1-5]_target Target fan speed +fan[1-5]_tolerance + Target speed tolerance + + +Untested; use at your own risk. + +Smart Fan IV mode (5) +--------------------- + +This mode offers multiple slopes to control the fan speed. The slopes can be +controlled by setting the pwm and temperature attributes. When the temperature +rises, the chip will calculate the DC/PWM output based on the current slope. +There are up to seven data points depending on the chip type. Subsequent data +points should be set to higher temperatures and higher pwm values to achieve +higher fan speeds with increasing temperature. The last data point reflects +critical temperature mode, in which the fans should run at full speed. + +pwm[1-5]_auto_point[1-7]_pwm + pwm value to be set if temperature reaches matching + temperature range. +pwm[1-5]_auto_point[1-7]_temp + Temperature over which the matching pwm is enabled. +pwm[1-5]_temp_tolerance + Temperature tolerance, unit millidegree Celsius +pwm[1-5]_crit_temp_tolerance + Temperature tolerance for critical temperature, + unit millidegree Celsius + +pwm[1-5]_step_up_time milliseconds before fan speed is increased +pwm[1-5]_step_down_time milliseconds before fan speed is decreased + +Usage Notes +----------- + +On various ASUS boards with NCT6776F, it appears that CPUTIN is not really +connected to anything and floats, or that it is connected to some non-standard +temperature measurement device. As a result, the temperature reported on CPUTIN +will not reflect a usable value. It often reports unreasonably high +temperatures, and in some cases the reported temperature declines if the actual +temperature increases (similar to the raw PECI temperature value - see PECI +specification for details). CPUTIN should therefore be be ignored on ASUS +boards. The CPU temperature on ASUS boards is reported from PECI 0. diff --git a/Documentation/hwmon/ntc_thermistor b/Documentation/hwmon/ntc_thermistor new file mode 100644 index 00000000000..057b77029f2 --- /dev/null +++ b/Documentation/hwmon/ntc_thermistor @@ -0,0 +1,93 @@ +Kernel driver ntc_thermistor +================= + +Supported thermistors from Murata: +* Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333 + Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', 'ncp15wl333' + Datasheet: Publicly available at Murata + +Other NTC thermistors can be supported simply by adding compensation +tables; e.g., NCP15WL333 support is added by the table ncpXXwl333. + +Authors: + MyungJoo Ham <myungjoo.ham@samsung.com> + +Description +----------- + +The NTC (Negative Temperature Coefficient) thermistor is a simple thermistor +that requires users to provide the resistance and lookup the corresponding +compensation table to get the temperature input. + +The NTC driver provides lookup tables with a linear approximation function +and four circuit models with an option not to use any of the four models. + +The four circuit models provided are: + + $: resister, [TH]: the thermistor + + 1. connect = NTC_CONNECTED_POSITIVE, pullup_ohm > 0 + + [pullup_uV] + | | + [TH] $ (pullup_ohm) + | | + +----+-----------------------[read_uV] + | + $ (pulldown_ohm) + | + --- (ground) + + 2. connect = NTC_CONNECTED_POSITIVE, pullup_ohm = 0 (not-connected) + + [pullup_uV] + | + [TH] + | + +----------------------------[read_uV] + | + $ (pulldown_ohm) + | + --- (ground) + + 3. connect = NTC_CONNECTED_GROUND, pulldown_ohm > 0 + + [pullup_uV] + | + $ (pullup_ohm) + | + +----+-----------------------[read_uV] + | | + [TH] $ (pulldown_ohm) + | | + -------- (ground) + + 4. connect = NTC_CONNECTED_GROUND, pulldown_ohm = 0 (not-connected) + + [pullup_uV] + | + $ (pullup_ohm) + | + +----------------------------[read_uV] + | + [TH] + | + --- (ground) + +When one of the four circuit models is used, read_uV, pullup_uV, pullup_ohm, +pulldown_ohm, and connect should be provided. When none of the four models +are suitable or the user can get the resistance directly, the user should +provide read_ohm and _not_ provide the others. + +Sysfs Interface +--------------- +name the mandatory global attribute, the thermistor name. + +temp1_type always 4 (thermistor) + RO + +temp1_input measure the temperature and provide the measured value. + (reading this file initiates the reading procedure.) + RO + +Note that each NTC thermistor has only _one_ thermistor; thus, only temp1 exists. diff --git a/Documentation/hwmon/pc87360 b/Documentation/hwmon/pc87360 index 89a8fcfa78d..d5f5cf16ce5 100644 --- a/Documentation/hwmon/pc87360 +++ b/Documentation/hwmon/pc87360 @@ -5,14 +5,9 @@ Supported chips: * National Semiconductor PC87360, PC87363, PC87364, PC87365 and PC87366 Prefixes: 'pc87360', 'pc87363', 'pc87364', 'pc87365', 'pc87366' Addresses scanned: none, address read from Super I/O config space - Datasheets: - http://www.national.com/pf/PC/PC87360.html - http://www.national.com/pf/PC/PC87363.html - http://www.national.com/pf/PC/PC87364.html - http://www.national.com/pf/PC/PC87365.html - http://www.national.com/pf/PC/PC87366.html - -Authors: Jean Delvare <khali@linux-fr.org> + Datasheets: No longer available + +Authors: Jean Delvare <jdelvare@suse.de> Thanks to Sandeep Mehta, Tonko de Rooy and Daniel Ceregatti for testing. Thanks to Rudolf Marek for helping me investigate conversion issues. diff --git a/Documentation/hwmon/pc87427 b/Documentation/hwmon/pc87427 new file mode 100644 index 00000000000..c313eb66e08 --- /dev/null +++ b/Documentation/hwmon/pc87427 @@ -0,0 +1,59 @@ +Kernel driver pc87427 +===================== + +Supported chips: + * National Semiconductor PC87427 + Prefix: 'pc87427' + Addresses scanned: none, address read from Super I/O config space + Datasheet: No longer available + +Author: Jean Delvare <jdelvare@suse.de> + +Thanks to Amir Habibi at Candelis for setting up a test system, and to +Michael Kress for testing several iterations of this driver. + + +Description +----------- + +The National Semiconductor Super I/O chip includes complete hardware +monitoring capabilities. It can monitor up to 18 voltages, 8 fans and +6 temperature sensors. Only the fans and temperatures are supported at +the moment, voltages aren't. + +This chip also has fan controlling features (up to 4 PWM outputs), +which are partly supported by this driver. + +The driver assumes that no more than one chip is present, which seems +reasonable. + + +Fan Monitoring +-------------- + +Fan rotation speeds are reported as 14-bit values from a gated clock +signal. Speeds down to 83 RPM can be measured. + +An alarm is triggered if the rotation speed drops below a programmable +limit. Another alarm is triggered if the speed is too low to be measured +(including stalled or missing fan). + + +Fan Speed Control +----------------- + +Fan speed can be controlled by PWM outputs. There are 4 possible modes: +always off, always on, manual and automatic. The latter isn't supported +by the driver: you can only return to that mode if it was the original +setting, and the configuration interface is missing. + + +Temperature Monitoring +---------------------- + +The PC87427 relies on external sensors (following the SensorPath +standard), so the resolution and range depend on the type of sensor +connected. The integer part can be 8-bit or 9-bit, and can be signed or +not. I couldn't find a way to figure out the external sensor data +temperature format, so user-space adjustment (typically by a factor 2) +may be required. diff --git a/Documentation/hwmon/pcf8591 b/Documentation/hwmon/pcf8591 new file mode 100644 index 00000000000..447c0702c0e --- /dev/null +++ b/Documentation/hwmon/pcf8591 @@ -0,0 +1,90 @@ +Kernel driver pcf8591 +===================== + +Supported chips: + * Philips/NXP PCF8591 + Prefix: 'pcf8591' + Addresses scanned: none + Datasheet: Publicly available at the NXP website + http://www.nxp.com/pip/PCF8591_6.html + +Authors: + Aurelien Jarno <aurelien@aurel32.net> + valuable contributions by Jan M. Sendler <sendler@sendler.de>, + Jean Delvare <jdelvare@suse.de> + + +Description +----------- + +The PCF8591 is an 8-bit A/D and D/A converter (4 analog inputs and one +analog output) for the I2C bus produced by Philips Semiconductors (now NXP). +It is designed to provide a byte I2C interface to up to 4 separate devices. + +The PCF8591 has 4 analog inputs programmable as single-ended or +differential inputs : +- mode 0 : four single ended inputs + Pins AIN0 to AIN3 are single ended inputs for channels 0 to 3 + +- mode 1 : three differential inputs + Pins AIN3 is the common negative differential input + Pins AIN0 to AIN2 are positive differential inputs for channels 0 to 2 + +- mode 2 : single ended and differential mixed + Pins AIN0 and AIN1 are single ended inputs for channels 0 and 1 + Pins AIN2 is the positive differential input for channel 3 + Pins AIN3 is the negative differential input for channel 3 + +- mode 3 : two differential inputs + Pins AIN0 is the positive differential input for channel 0 + Pins AIN1 is the negative differential input for channel 0 + Pins AIN2 is the positive differential input for channel 1 + Pins AIN3 is the negative differential input for channel 1 + +See the datasheet for details. + +Module parameters +----------------- + +* input_mode int + + Analog input mode: + 0 = four single ended inputs + 1 = three differential inputs + 2 = single ended and differential mixed + 3 = two differential inputs + + +Accessing PCF8591 via /sys interface +------------------------------------- + +The PCF8591 is plainly impossible to detect! Thus the driver won't even +try. You have to explicitly instantiate the device at the relevant +address (in the interval [0x48..0x4f]) either through platform data, or +using the sysfs interface. See Documentation/i2c/instantiating-devices +for details. + +Directories are being created for each instantiated PCF8591: + +/sys/bus/i2c/devices/<0>-<1>/ +where <0> is the bus the chip is connected to (e. g. i2c-0) +and <1> the chip address ([48..4f]) + +Inside these directories, there are such files: +in0_input, in1_input, in2_input, in3_input, out0_enable, out0_output, name + +Name contains chip name. + +The in0_input, in1_input, in2_input and in3_input files are RO. Reading gives +the value of the corresponding channel. Depending on the current analog inputs +configuration, files in2_input and in3_input may not exist. Values range +from 0 to 255 for single ended inputs and -128 to +127 for differential inputs +(8-bit ADC). + +The out0_enable file is RW. Reading gives "1" for analog output enabled and +"0" for analog output disabled. Writing accepts "0" and "1" accordingly. + +The out0_output file is RW. Writing a number between 0 and 255 (8-bit DAC), send +the value to the digital-to-analog converter. Note that a voltage will +only appears on AOUT pin if aout0_enable equals 1. Reading returns the last +value written. diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus new file mode 100644 index 00000000000..cf756ed48ff --- /dev/null +++ b/Documentation/hwmon/pmbus @@ -0,0 +1,213 @@ +Kernel driver pmbus +==================== + +Supported chips: + * Ericsson BMR453, BMR454 + Prefixes: 'bmr453', 'bmr454' + Addresses scanned: - + Datasheet: + http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146395 + * ON Semiconductor ADP4000, NCP4200, NCP4208 + Prefixes: 'adp4000', 'ncp4200', 'ncp4208' + Addresses scanned: - + Datasheets: + http://www.onsemi.com/pub_link/Collateral/ADP4000-D.PDF + http://www.onsemi.com/pub_link/Collateral/NCP4200-D.PDF + http://www.onsemi.com/pub_link/Collateral/JUNE%202009-%20REV.%200.PDF + * Lineage Power + Prefixes: 'mdt040', 'pdt003', 'pdt006', 'pdt012', 'udt020' + Addresses scanned: - + Datasheets: + http://www.lineagepower.com/oem/pdf/PDT003A0X.pdf + http://www.lineagepower.com/oem/pdf/PDT006A0X.pdf + http://www.lineagepower.com/oem/pdf/PDT012A0X.pdf + http://www.lineagepower.com/oem/pdf/UDT020A0X.pdf + http://www.lineagepower.com/oem/pdf/MDT040A0X.pdf + * Texas Instruments TPS40400, TPS40422 + Prefixes: 'tps40400', 'tps40422' + Addresses scanned: - + Datasheets: + http://www.ti.com/lit/gpn/tps40400 + http://www.ti.com/lit/gpn/tps40422 + * Generic PMBus devices + Prefix: 'pmbus' + Addresses scanned: - + Datasheet: n.a. + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for various PMBus compliant devices. +It supports voltage, current, power, and temperature sensors as supported +by the device. + +Each monitored channel has its own high and low limits, plus a critical +limit. + +Fan support will be added in a later version of this driver. + + +Usage Notes +----------- + +This driver does not probe for PMBus devices, since there is no register +which can be safely used to identify the chip (The MFG_ID register is not +supported by all chips), and since there is no well defined address range for +PMBus devices. You will have to instantiate the devices explicitly. + +Example: the following will load the driver for an LTC2978 at address 0x60 +on I2C bus #1: +$ modprobe pmbus +$ echo ltc2978 0x60 > /sys/bus/i2c/devices/i2c-1/new_device + + +Platform data support +--------------------- + +Support for additional PMBus chips can be added by defining chip parameters in +a new chip specific driver file. For example, (untested) code to add support for +Emerson DS1200 power modules might look as follows. + +static struct pmbus_driver_info ds1200_info = { + .pages = 1, + /* Note: All other sensors are in linear mode */ + .direct[PSC_VOLTAGE_OUT] = true, + .direct[PSC_TEMPERATURE] = true, + .direct[PSC_CURRENT_OUT] = true, + .m[PSC_VOLTAGE_IN] = 1, + .b[PSC_VOLTAGE_IN] = 0, + .R[PSC_VOLTAGE_IN] = 3, + .m[PSC_VOLTAGE_OUT] = 1, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = 3, + .m[PSC_TEMPERATURE] = 1, + .b[PSC_TEMPERATURE] = 0, + .R[PSC_TEMPERATURE] = 3, + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_STATUS_INPUT + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT + | PMBUS_HAVE_PIN | PMBUS_HAVE_POUT + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP + | PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12, +}; + +static int ds1200_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + return pmbus_do_probe(client, id, &ds1200_info); +} + +static int ds1200_remove(struct i2c_client *client) +{ + return pmbus_do_remove(client); +} + +static const struct i2c_device_id ds1200_id[] = { + {"ds1200", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, ds1200_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver ds1200_driver = { + .driver = { + .name = "ds1200", + }, + .probe = ds1200_probe, + .remove = ds1200_remove, + .id_table = ds1200_id, +}; + +static int __init ds1200_init(void) +{ + return i2c_add_driver(&ds1200_driver); +} + +static void __exit ds1200_exit(void) +{ + i2c_del_driver(&ds1200_driver); +} + + +Sysfs entries +------------- + +When probing the chip, the driver identifies which PMBus registers are +supported, and determines available sensors from this information. +Attribute files only exist if respective sensors are supported by the chip. +Labels are provided to inform the user about the sensor associated with +a given sysfs entry. + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +inX_input Measured voltage. From READ_VIN or READ_VOUT register. +inX_min Minimum Voltage. + From VIN_UV_WARN_LIMIT or VOUT_UV_WARN_LIMIT register. +inX_max Maximum voltage. + From VIN_OV_WARN_LIMIT or VOUT_OV_WARN_LIMIT register. +inX_lcrit Critical minimum Voltage. + From VIN_UV_FAULT_LIMIT or VOUT_UV_FAULT_LIMIT register. +inX_crit Critical maximum voltage. + From VIN_OV_FAULT_LIMIT or VOUT_OV_FAULT_LIMIT register. +inX_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +inX_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +inX_lcrit_alarm Voltage critical low alarm. + From VOLTAGE_UV_FAULT status. +inX_crit_alarm Voltage critical high alarm. + From VOLTAGE_OV_FAULT status. +inX_label "vin", "vcap", or "voutY" + +currX_input Measured current. From READ_IIN or READ_IOUT register. +currX_max Maximum current. + From IIN_OC_WARN_LIMIT or IOUT_OC_WARN_LIMIT register. +currX_lcrit Critical minimum output current. + From IOUT_UC_FAULT_LIMIT register. +currX_crit Critical maximum current. + From IIN_OC_FAULT_LIMIT or IOUT_OC_FAULT_LIMIT register. +currX_alarm Current high alarm. + From IIN_OC_WARNING or IOUT_OC_WARNING status. +currX_max_alarm Current high alarm. + From IIN_OC_WARN_LIMIT or IOUT_OC_WARN_LIMIT status. +currX_lcrit_alarm Output current critical low alarm. + From IOUT_UC_FAULT status. +currX_crit_alarm Current critical high alarm. + From IIN_OC_FAULT or IOUT_OC_FAULT status. +currX_label "iin" or "ioutY" + +powerX_input Measured power. From READ_PIN or READ_POUT register. +powerX_cap Output power cap. From POUT_MAX register. +powerX_max Power limit. From PIN_OP_WARN_LIMIT or + POUT_OP_WARN_LIMIT register. +powerX_crit Critical output power limit. + From POUT_OP_FAULT_LIMIT register. +powerX_alarm Power high alarm. + From PIN_OP_WARNING or POUT_OP_WARNING status. +powerX_crit_alarm Output power critical high alarm. + From POUT_OP_FAULT status. +powerX_label "pin" or "poutY" + +tempX_input Measured temperature. + From READ_TEMPERATURE_X register. +tempX_min Mimimum temperature. From UT_WARN_LIMIT register. +tempX_max Maximum temperature. From OT_WARN_LIMIT register. +tempX_lcrit Critical low temperature. + From UT_FAULT_LIMIT register. +tempX_crit Critical high temperature. + From OT_FAULT_LIMIT register. +tempX_min_alarm Chip temperature low alarm. Set by comparing + READ_TEMPERATURE_X with UT_WARN_LIMIT if + TEMP_UT_WARNING status is set. +tempX_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_X with OT_WARN_LIMIT if + TEMP_OT_WARNING status is set. +tempX_lcrit_alarm Chip temperature critical low alarm. Set by comparing + READ_TEMPERATURE_X with UT_FAULT_LIMIT if + TEMP_UT_FAULT status is set. +tempX_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_X with OT_FAULT_LIMIT if + TEMP_OT_FAULT status is set. diff --git a/Documentation/hwmon/pmbus-core b/Documentation/hwmon/pmbus-core new file mode 100644 index 00000000000..31e4720fed1 --- /dev/null +++ b/Documentation/hwmon/pmbus-core @@ -0,0 +1,283 @@ +PMBus core driver and internal API +================================== + +Introduction +============ + +[from pmbus.org] The Power Management Bus (PMBus) is an open standard +power-management protocol with a fully defined command language that facilitates +communication with power converters and other devices in a power system. The +protocol is implemented over the industry-standard SMBus serial interface and +enables programming, control, and real-time monitoring of compliant power +conversion products. This flexible and highly versatile standard allows for +communication between devices based on both analog and digital technologies, and +provides true interoperability which will reduce design complexity and shorten +time to market for power system designers. Pioneered by leading power supply and +semiconductor companies, this open power system standard is maintained and +promoted by the PMBus Implementers Forum (PMBus-IF), comprising 30+ adopters +with the objective to provide support to, and facilitate adoption among, users. + +Unfortunately, while PMBus commands are standardized, there are no mandatory +commands, and manufacturers can add as many non-standard commands as they like. +Also, different PMBUs devices act differently if non-supported commands are +executed. Some devices return an error, some devices return 0xff or 0xffff and +set a status error flag, and some devices may simply hang up. + +Despite all those difficulties, a generic PMBus device driver is still useful +and supported since kernel version 2.6.39. However, it was necessary to support +device specific extensions in addition to the core PMBus driver, since it is +simply unknown what new device specific functionality PMBus device developers +come up with next. + +To make device specific extensions as scalable as possible, and to avoid having +to modify the core PMBus driver repeatedly for new devices, the PMBus driver was +split into core, generic, and device specific code. The core code (in +pmbus_core.c) provides generic functionality. The generic code (in pmbus.c) +provides support for generic PMBus devices. Device specific code is responsible +for device specific initialization and, if needed, maps device specific +functionality into generic functionality. This is to some degree comparable +to PCI code, where generic code is augmented as needed with quirks for all kinds +of devices. + +PMBus device capabilities auto-detection +======================================== + +For generic PMBus devices, code in pmbus.c attempts to auto-detect all supported +PMBus commands. Auto-detection is somewhat limited, since there are simply too +many variables to consider. For example, it is almost impossible to autodetect +which PMBus commands are paged and which commands are replicated across all +pages (see the PMBus specification for details on multi-page PMBus devices). + +For this reason, it often makes sense to provide a device specific driver if not +all commands can be auto-detected. The data structures in this driver can be +used to inform the core driver about functionality supported by individual +chips. + +Some commands are always auto-detected. This applies to all limit commands +(lcrit, min, max, and crit attributes) as well as associated alarm attributes. +Limits and alarm attributes are auto-detected because there are simply too many +possible combinations to provide a manual configuration interface. + +PMBus internal API +================== + +The API between core and device specific PMBus code is defined in +drivers/hwmon/pmbus/pmbus.h. In addition to the internal API, pmbus.h defines +standard PMBus commands and virtual PMBus commands. + +Standard PMBus commands +----------------------- + +Standard PMBus commands (commands values 0x00 to 0xff) are defined in the PMBUs +specification. + +Virtual PMBus commands +---------------------- + +Virtual PMBus commands are provided to enable support for non-standard +functionality which has been implemented by several chip vendors and is thus +desirable to support. + +Virtual PMBus commands start with command value 0x100 and can thus easily be +distinguished from standard PMBus commands (which can not have values larger +than 0xff). Support for virtual PMBus commands is device specific and thus has +to be implemented in device specific code. + +Virtual commands are named PMBUS_VIRT_xxx and start with PMBUS_VIRT_BASE. All +virtual commands are word sized. + +There are currently two types of virtual commands. + +- READ commands are read-only; writes are either ignored or return an error. +- RESET commands are read/write. Reading reset registers returns zero + (used for detection), writing any value causes the associated history to be + reset. + +Virtual commands have to be handled in device specific driver code. Chip driver +code returns non-negative values if a virtual command is supported, or a +negative error code if not. The chip driver may return -ENODATA or any other +Linux error code in this case, though an error code other than -ENODATA is +handled more efficiently and thus preferred. Either case, the calling PMBus +core code will abort if the chip driver returns an error code when reading +or writing virtual registers (in other words, the PMBus core code will never +send a virtual command to a chip). + +PMBus driver information +------------------------ + +PMBus driver information, defined in struct pmbus_driver_info, is the main means +for device specific drivers to pass information to the core PMBus driver. +Specifically, it provides the following information. + +- For devices supporting its data in Direct Data Format, it provides coefficients + for converting register values into normalized data. This data is usually + provided by chip manufacturers in device datasheets. +- Supported chip functionality can be provided to the core driver. This may be + necessary for chips which react badly if non-supported commands are executed, + and/or to speed up device detection and initialization. +- Several function entry points are provided to support overriding and/or + augmenting generic command execution. This functionality can be used to map + non-standard PMBus commands to standard commands, or to augment standard + command return values with device specific information. + + API functions + ------------- + + Functions provided by chip driver + --------------------------------- + + All functions return the command return value (read) or zero (write) if + successful. A return value of -ENODATA indicates that there is no manufacturer + specific command, but that a standard PMBus command may exist. Any other + negative return value indicates that the commands does not exist for this + chip, and that no attempt should be made to read or write the standard + command. + + As mentioned above, an exception to this rule applies to virtual commands, + which _must_ be handled in driver specific code. See "Virtual PMBus Commands" + above for more details. + + Command execution in the core PMBus driver code is as follows. + + if (chip_access_function) { + status = chip_access_function(); + if (status != -ENODATA) + return status; + } + if (command >= PMBUS_VIRT_BASE) /* For word commands/registers only */ + return -EINVAL; + return generic_access(); + + Chip drivers may provide pointers to the following functions in struct + pmbus_driver_info. All functions are optional. + + int (*read_byte_data)(struct i2c_client *client, int page, int reg); + + Read byte from page <page>, register <reg>. + <page> may be -1, which means "current page". + + int (*read_word_data)(struct i2c_client *client, int page, int reg); + + Read word from page <page>, register <reg>. + + int (*write_word_data)(struct i2c_client *client, int page, int reg, + u16 word); + + Write word to page <page>, register <reg>. + + int (*write_byte)(struct i2c_client *client, int page, u8 value); + + Write byte to page <page>, register <reg>. + <page> may be -1, which means "current page". + + int (*identify)(struct i2c_client *client, struct pmbus_driver_info *info); + + Determine supported PMBus functionality. This function is only necessary + if a chip driver supports multiple chips, and the chip functionality is not + pre-determined. It is currently only used by the generic pmbus driver + (pmbus.c). + + Functions exported by core driver + --------------------------------- + + Chip drivers are expected to use the following functions to read or write + PMBus registers. Chip drivers may also use direct I2C commands. If direct I2C + commands are used, the chip driver code must not directly modify the current + page, since the selected page is cached in the core driver and the core driver + will assume that it is selected. Using pmbus_set_page() to select a new page + is mandatory. + + int pmbus_set_page(struct i2c_client *client, u8 page); + + Set PMBus page register to <page> for subsequent commands. + + int pmbus_read_word_data(struct i2c_client *client, u8 page, u8 reg); + + Read word data from <page>, <reg>. Similar to i2c_smbus_read_word_data(), but + selects page first. + + int pmbus_write_word_data(struct i2c_client *client, u8 page, u8 reg, + u16 word); + + Write word data to <page>, <reg>. Similar to i2c_smbus_write_word_data(), but + selects page first. + + int pmbus_read_byte_data(struct i2c_client *client, int page, u8 reg); + + Read byte data from <page>, <reg>. Similar to i2c_smbus_read_byte_data(), but + selects page first. <page> may be -1, which means "current page". + + int pmbus_write_byte(struct i2c_client *client, int page, u8 value); + + Write byte data to <page>, <reg>. Similar to i2c_smbus_write_byte(), but + selects page first. <page> may be -1, which means "current page". + + void pmbus_clear_faults(struct i2c_client *client); + + Execute PMBus "Clear Fault" command on all chip pages. + This function calls the device specific write_byte function if defined. + Therefore, it must _not_ be called from that function. + + bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg); + + Check if byte register exists. Return true if the register exists, false + otherwise. + This function calls the device specific write_byte function if defined to + obtain the chip status. Therefore, it must _not_ be called from that function. + + bool pmbus_check_word_register(struct i2c_client *client, int page, int reg); + + Check if word register exists. Return true if the register exists, false + otherwise. + This function calls the device specific write_byte function if defined to + obtain the chip status. Therefore, it must _not_ be called from that function. + + int pmbus_do_probe(struct i2c_client *client, const struct i2c_device_id *id, + struct pmbus_driver_info *info); + + Execute probe function. Similar to standard probe function for other drivers, + with the pointer to struct pmbus_driver_info as additional argument. Calls + identify function if supported. Must only be called from device probe + function. + + void pmbus_do_remove(struct i2c_client *client); + + Execute driver remove function. Similar to standard driver remove function. + + const struct pmbus_driver_info + *pmbus_get_driver_info(struct i2c_client *client); + + Return pointer to struct pmbus_driver_info as passed to pmbus_do_probe(). + + +PMBus driver platform data +========================== + +PMBus platform data is defined in include/linux/i2c/pmbus.h. Platform data +currently only provides a flag field with a single bit used. + +#define PMBUS_SKIP_STATUS_CHECK (1 << 0) + +struct pmbus_platform_data { + u32 flags; /* Device specific flags */ +}; + + +Flags +----- + +PMBUS_SKIP_STATUS_CHECK + +During register detection, skip checking the status register for +communication or command errors. + +Some PMBus chips respond with valid data when trying to read an unsupported +register. For such chips, checking the status register is mandatory when +trying to determine if a chip register exists or not. +Other PMBus chips don't support the STATUS_CML register, or report +communication errors for no explicable reason. For such chips, checking the +status register must be disabled. + +Some i2c controllers do not support single-byte commands (write commands with +no data, i2c_smbus_write_byte()). With such controllers, clearing the status +register is impossible, and the PMBUS_SKIP_STATUS_CHECK flag must be set. diff --git a/Documentation/hwmon/sch5627 b/Documentation/hwmon/sch5627 new file mode 100644 index 00000000000..0551d266c51 --- /dev/null +++ b/Documentation/hwmon/sch5627 @@ -0,0 +1,27 @@ +Kernel driver sch5627 +===================== + +Supported chips: + * SMSC SCH5627 + Prefix: 'sch5627' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Application Note available upon request + +Author: Hans de Goede <hdegoede@redhat.com> + + +Description +----------- + +SMSC SCH5627 Super I/O chips include complete hardware monitoring +capabilities. They can monitor up to 5 voltages, 4 fans and 8 temperatures. + +The SMSC SCH5627 hardware monitoring part also contains an integrated +watchdog. In order for this watchdog to function some motherboard specific +initialization most be done by the BIOS, so if the watchdog is not enabled +by the BIOS the sch5627 driver will not register a watchdog device. + +The hardware monitoring part of the SMSC SCH5627 is accessed by talking +through an embedded microcontroller. An application note describing the +protocol for communicating with the microcontroller is available upon +request. Please mail me if you want a copy. diff --git a/Documentation/hwmon/sch5636 b/Documentation/hwmon/sch5636 new file mode 100644 index 00000000000..7b0a01da071 --- /dev/null +++ b/Documentation/hwmon/sch5636 @@ -0,0 +1,34 @@ +Kernel driver sch5636 +===================== + +Supported chips: + * SMSC SCH5636 + Prefix: 'sch5636' + Addresses scanned: none, address read from Super I/O config space + +Author: Hans de Goede <hdegoede@redhat.com> + + +Description +----------- + +SMSC SCH5636 Super I/O chips include an embedded microcontroller for +hardware monitoring solutions, allowing motherboard manufacturers to create +their own custom hwmon solution based upon the SCH5636. + +Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636 based +hwmon solution. The sch5636 driver runs a sanity check on loading to ensure +it is dealing with a Fujitsu Theseus and not with another custom SCH5636 based +hwmon solution. + +The Fujitsu Theseus can monitor up to 5 voltages, 8 fans and 16 +temperatures. Note that the driver detects how many fan headers / +temperature sensors are actually implemented on the motherboard, so you will +likely see fewer temperature and fan inputs. + +The Fujitsu Theseus hwmon solution also contains an integrated watchdog. +This watchdog is fully supported by the sch5636 driver. + +An application note describing the Theseus' registers, as well as an +application note describing the protocol for communicating with the +microcontroller is available upon request. Please mail me if you want a copy. diff --git a/Documentation/hwmon/sht15 b/Documentation/hwmon/sht15 new file mode 100644 index 00000000000..778987d1856 --- /dev/null +++ b/Documentation/hwmon/sht15 @@ -0,0 +1,74 @@ +Kernel driver sht15 +=================== + +Authors: + * Wouter Horre + * Jonathan Cameron + * Vivien Didelot <vivien.didelot@savoirfairelinux.com> + * Jerome Oufella <jerome.oufella@savoirfairelinux.com> + +Supported chips: + * Sensirion SHT10 + Prefix: 'sht10' + + * Sensirion SHT11 + Prefix: 'sht11' + + * Sensirion SHT15 + Prefix: 'sht15' + + * Sensirion SHT71 + Prefix: 'sht71' + + * Sensirion SHT75 + Prefix: 'sht75' + +Datasheet: Publicly available at the Sensirion website +http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf + +Description +----------- + +The SHT10, SHT11, SHT15, SHT71, and SHT75 are humidity and temperature +sensors. + +The devices communicate using two GPIO lines. + +Supported resolutions for the measurements are 14 bits for temperature and 12 +bits for humidity, or 12 bits for temperature and 8 bits for humidity. + +The humidity calibration coefficients are programmed into an OTP memory on the +chip. These coefficients are used to internally calibrate the signals from the +sensors. Disabling the reload of those coefficients allows saving 10ms for each +measurement and decrease power consumption, while losing on precision. + +Some options may be set directly in the sht15_platform_data structure +or via sysfs attributes. + +Notes: + * The regulator supply name is set to "vcc". + * If a CRC validation fails, a soft reset command is sent, which resets + status register to its hardware default value, but the driver will try to + restore the previous device configuration. + +Platform data +------------- + +* checksum: + set it to true to enable CRC validation of the readings (default to false). +* no_otp_reload: + flag to indicate not to reload from OTP (default to false). +* low_resolution: + flag to indicate the temp/humidity resolution to use (default to false). + +Sysfs interface +--------------- + +* temp1_input: temperature input +* humidity1_input: humidity input +* heater_enable: write 1 in this attribute to enable the on-chip heater, + 0 to disable it. Be careful not to enable the heater + for too long. +* temp1_fault: if 1, this means that the voltage is low (below 2.47V) and + measurement may be invalid. +* humidity1_fault: same as temp1_fault. diff --git a/Documentation/hwmon/sht21 b/Documentation/hwmon/sht21 new file mode 100644 index 00000000000..db17fda45c3 --- /dev/null +++ b/Documentation/hwmon/sht21 @@ -0,0 +1,49 @@ +Kernel driver sht21 +=================== + +Supported chips: + * Sensirion SHT21 + Prefix: 'sht21' + Addresses scanned: none + Datasheet: Publicly available at the Sensirion website + http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT21.pdf + + * Sensirion SHT25 + Prefix: 'sht21' + Addresses scanned: none + Datasheet: Publicly available at the Sensirion website + http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT25.pdf + +Author: + Urs Fleisch <urs.fleisch@sensirion.com> + +Description +----------- + +The SHT21 and SHT25 are humidity and temperature sensors in a DFN package of +only 3 x 3 mm footprint and 1.1 mm height. The difference between the two +devices is the higher level of precision of the SHT25 (1.8% relative humidity, +0.2 degree Celsius) compared with the SHT21 (2.0% relative humidity, +0.3 degree Celsius). + +The devices communicate with the I2C protocol. All sensors are set to the same +I2C address 0x40, so an entry with I2C_BOARD_INFO("sht21", 0x40) can be used +in the board setup code. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input + +Notes +----- + +The driver uses the default resolution settings of 12 bit for humidity and 14 +bit for temperature, which results in typical measurement times of 22 ms for +humidity and 66 ms for temperature. To keep self heating below 0.1 degree +Celsius, the device should not be active for more than 10% of the time, +e.g. maximum two measurements per second at the given resolution. + +Different resolutions, the on-chip heater, using the CRC checksum and reading +the serial number are not supported yet. diff --git a/Documentation/hwmon/shtc1 b/Documentation/hwmon/shtc1 new file mode 100644 index 00000000000..6b1e05458f0 --- /dev/null +++ b/Documentation/hwmon/shtc1 @@ -0,0 +1,43 @@ +Kernel driver shtc1 +=================== + +Supported chips: + * Sensirion SHTC1 + Prefix: 'shtc1' + Addresses scanned: none + Datasheet: http://www.sensirion.com/file/datasheet_shtc1 + + * Sensirion SHTW1 + Prefix: 'shtw1' + Addresses scanned: none + Datasheet: Not publicly available + +Author: + Johannes Winkelmann <johannes.winkelmann@sensirion.com> + +Description +----------- + +This driver implements support for the Sensirion SHTC1 chip, a humidity and +temperature sensor. Temperature is measured in degrees celsius, relative +humidity is expressed as a percentage. Driver can be used as well for SHTW1 +chip, which has the same electrical interface. + +The device communicates with the I2C protocol. All sensors are set to I2C +address 0x70. See Documentation/i2c/instantiating-devices for methods to +instantiate the device. + +There are two options configurable by means of shtc1_platform_data: +1. blocking (pull the I2C clock line down while performing the measurement) or + non-blocking mode. Blocking mode will guarantee the fastest result but + the I2C bus will be busy during that time. By default, non-blocking mode + is used. Make sure clock-stretching works properly on your device if you + want to use blocking mode. +2. high or low accuracy. High accuracy is used by default and using it is + strongly recommended. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input diff --git a/Documentation/hwmon/sis5595 b/Documentation/hwmon/sis5595 index b7ae36b8cdf..4f8877a34f3 100644 --- a/Documentation/hwmon/sis5595 +++ b/Documentation/hwmon/sis5595 @@ -8,7 +8,7 @@ Supported chips: Datasheet: Publicly available at the Silicon Integrated Systems Corp. site. Authors: - Kyösti Mälkki <kmalkki@cc.hut.fi>, + Kyösti Mälkki <kmalkki@cc.hut.fi>, Mark D. Studebaker <mdsxyz123@yahoo.com>, Aurelien Jarno <aurelien@aurel32.net> 2.6 port diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665 new file mode 100644 index 00000000000..a341eeedab7 --- /dev/null +++ b/Documentation/hwmon/smm665 @@ -0,0 +1,157 @@ +Kernel driver smm665 +==================== + +Supported chips: + * Summit Microelectronics SMM465 + Prefix: 'smm465' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf + * Summit Microelectronics SMM665, SMM665B + Prefix: 'smm665' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf + * Summit Microelectronics SMM665C + Prefix: 'smm665c' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf + * Summit Microelectronics SMM764 + Prefix: 'smm764' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf + * Summit Microelectronics SMM766, SMM766B + Prefix: 'smm766' + Addresses scanned: - + Datasheets: + http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf + http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Module Parameters +----------------- + +* vref: int + Default: 1250 (mV) + Reference voltage on VREF_ADC pin in mV. It should not be necessary to set + this parameter unless a non-default reference voltage is used. + + +Description +----------- + +[From datasheet] The SMM665 is an Active DC Output power supply Controller +that monitors, margins and cascade sequences power. The part monitors six +power supply channels as well as VDD, 12V input, two general-purpose analog +inputs and an internal temperature sensor using a 10-bit ADC. + +Each monitored channel has its own high and low limits, plus a critical +limit. + +Support for SMM465, SMM764, and SMM766 has been implemented but is untested. + + +Usage Notes +----------- + +This driver does not probe for devices, since there is no register which +can be safely used to identify the chip. You will have to instantiate +the devices explicitly. When instantiating the device, you have to specify +its configuration register address. + +Example: the following will load the driver for an SMM665 at address 0x57 +on I2C bus #1: +$ modprobe smm665 +$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +This driver uses the values in the datasheet to convert ADC register values +into the values specified in the sysfs-interface document. All attributes are +read only. + +Min, max, lcrit, and crit values are used by the chip to trigger external signals +and/or other activity. Triggered signals can include HEALTHY, RST, Power Off, +or Fault depending on the chip configuration. The driver reports values as lcrit +or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or +max otherwise. For details please see the SMM665 datasheet. + +For SMM465 and SMM764, values for Channel E and F are reported but undefined. + +in1_input 12V input voltage (mV) +in2_input 3.3V (VDD) input voltage (mV) +in3_input Channel A voltage (mV) +in4_input Channel B voltage (mV) +in5_input Channel C voltage (mV) +in6_input Channel D voltage (mV) +in7_input Channel E voltage (mV) +in8_input Channel F voltage (mV) +in9_input AIN1 voltage (mV) +in10_input AIN2 voltage (mV) + +in1_min 12v input minimum voltage (mV) +in2_min 3.3V (VDD) input minimum voltage (mV) +in3_min Channel A minimum voltage (mV) +in4_min Channel B minimum voltage (mV) +in5_min Channel C minimum voltage (mV) +in6_min Channel D minimum voltage (mV) +in7_min Channel E minimum voltage (mV) +in8_min Channel F minimum voltage (mV) +in9_min AIN1 minimum voltage (mV) +in10_min AIN2 minimum voltage (mV) + +in1_max 12v input maximum voltage (mV) +in2_max 3.3V (VDD) input maximum voltage (mV) +in3_max Channel A maximum voltage (mV) +in4_max Channel B maximum voltage (mV) +in5_max Channel C maximum voltage (mV) +in6_max Channel D maximum voltage (mV) +in7_max Channel E maximum voltage (mV) +in8_max Channel F maximum voltage (mV) +in9_max AIN1 maximum voltage (mV) +in10_max AIN2 maximum voltage (mV) + +in1_lcrit 12v input critical minimum voltage (mV) +in2_lcrit 3.3V (VDD) input critical minimum voltage (mV) +in3_lcrit Channel A critical minimum voltage (mV) +in4_lcrit Channel B critical minimum voltage (mV) +in5_lcrit Channel C critical minimum voltage (mV) +in6_lcrit Channel D critical minimum voltage (mV) +in7_lcrit Channel E critical minimum voltage (mV) +in8_lcrit Channel F critical minimum voltage (mV) +in9_lcrit AIN1 critical minimum voltage (mV) +in10_lcrit AIN2 critical minimum voltage (mV) + +in1_crit 12v input critical maximum voltage (mV) +in2_crit 3.3V (VDD) input critical maximum voltage (mV) +in3_crit Channel A critical maximum voltage (mV) +in4_crit Channel B critical maximum voltage (mV) +in5_crit Channel C critical maximum voltage (mV) +in6_crit Channel D critical maximum voltage (mV) +in7_crit Channel E critical maximum voltage (mV) +in8_crit Channel F critical maximum voltage (mV) +in9_crit AIN1 critical maximum voltage (mV) +in10_crit AIN2 critical maximum voltage (mV) + +in1_crit_alarm 12v input critical alarm +in2_crit_alarm 3.3V (VDD) input critical alarm +in3_crit_alarm Channel A critical alarm +in4_crit_alarm Channel B critical alarm +in5_crit_alarm Channel C critical alarm +in6_crit_alarm Channel D critical alarm +in7_crit_alarm Channel E critical alarm +in8_crit_alarm Channel F critical alarm +in9_crit_alarm AIN1 critical alarm +in10_crit_alarm AIN2 critical alarm + +temp1_input Chip temperature +temp1_min Mimimum chip temperature +temp1_max Maximum chip temperature +temp1_crit Critical chip temperature +temp1_crit_alarm Temperature critical alarm diff --git a/Documentation/hwmon/smsc47b397 b/Documentation/hwmon/smsc47b397 index 20682f15ae4..3a43b694892 100644 --- a/Documentation/hwmon/smsc47b397 +++ b/Documentation/hwmon/smsc47b397 @@ -4,6 +4,7 @@ Kernel driver smsc47b397 Supported chips: * SMSC LPC47B397-NC * SMSC SCH5307-NS + * SMSC SCH5317 Prefix: 'smsc47b397' Addresses scanned: none, address read from Super I/O config space Datasheet: In this file @@ -18,8 +19,8 @@ The following specification describes the SMSC LPC47B397-NC[1] sensor chip provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected by Mark M. Hoffman <mhoffman@lightlink.com>. -[1] And SMSC SCH5307-NS, which has a different device ID but is otherwise -compatible. +[1] And SMSC SCH5307-NS and SCH5317, which have different device IDs but are +otherwise compatible. * * * * * @@ -131,7 +132,7 @@ OUT DX,AL The registers of interest for identifying the SIO on the dc7100 are Device ID (0x20) and Device Rev (0x21). -The Device ID will read 0x6F (for SCH5307-NS, 0x81) +The Device ID will read 0x6F (0x81 for SCH5307-NS, and 0x85 for SCH5317) The Device Rev currently reads 0x01 Obtaining the HWM Base Address. diff --git a/Documentation/hwmon/smsc47m1 b/Documentation/hwmon/smsc47m1 index c15bbe68264..10a24b42068 100644 --- a/Documentation/hwmon/smsc47m1 +++ b/Documentation/hwmon/smsc47m1 @@ -2,16 +2,19 @@ Kernel driver smsc47m1 ====================== Supported chips: - * SMSC LPC47B27x, LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192 + * SMSC LPC47B27x, LPC47M112, LPC47M10x, LPC47M13x, LPC47M14x, + LPC47M15x and LPC47M192 Addresses scanned: none, address read from Super I/O config space Prefix: 'smsc47m1' Datasheets: - http://www.smsc.com/main/datasheets/47b27x.pdf - http://www.smsc.com/main/datasheets/47m10x.pdf - http://www.smsc.com/main/tools/discontinued/47m13x.pdf - http://www.smsc.com/main/datasheets/47m14x.pdf - http://www.smsc.com/main/tools/discontinued/47m15x.pdf - http://www.smsc.com/main/datasheets/47m192.pdf + http://www.smsc.com/media/Downloads_Public/Data_Sheets/47b272.pdf + http://www.smsc.com/media/Downloads_Public/Data_Sheets/47m10x.pdf + http://www.smsc.com/media/Downloads_Public/Data_Sheets/47m112.pdf + http://www.smsc.com/ + * SMSC LPC47M292 + Addresses scanned: none, address read from Super I/O config space + Prefix: 'smsc47m2' + Datasheet: Not public * SMSC LPC47M997 Addresses scanned: none, address read from Super I/O config space Prefix: 'smsc47m1' @@ -22,7 +25,7 @@ Authors: With assistance from Bruce Allen <ballen@uwm.edu>, and his fan.c program: http://www.lsc-group.phys.uwm.edu/%7Eballen/driver/ Gabriele Gorla <gorlik@yahoo.com>, - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Description ----------- @@ -30,9 +33,10 @@ Description The Standard Microsystems Corporation (SMSC) 47M1xx Super I/O chips contain monitoring and PWM control circuitry for two fans. -The 47M15x and 47M192 chips contain a full 'hardware monitoring block' -in addition to the fan monitoring and control. The hardware monitoring -block is not supported by the driver. +The LPC47M15x, LPC47M192 and LPC47M292 chips contain a full 'hardware +monitoring block' in addition to the fan monitoring and control. The +hardware monitoring block is not supported by this driver, use the +smsc47m192 driver for that. No documentation is available for the 47M997, but it has the same device ID as the 47M15x and 47M192 chips and seems to be compatible. diff --git a/Documentation/hwmon/smsc47m192 b/Documentation/hwmon/smsc47m192 new file mode 100644 index 00000000000..6d54ecb7b3f --- /dev/null +++ b/Documentation/hwmon/smsc47m192 @@ -0,0 +1,103 @@ +Kernel driver smsc47m192 +======================== + +Supported chips: + * SMSC LPC47M192, LPC47M15x, LPC47M292 and LPC47M997 + Prefix: 'smsc47m192' + Addresses scanned: I2C 0x2c - 0x2d + Datasheet: The datasheet for LPC47M192 is publicly available from + http://www.smsc.com/ + The LPC47M15x, LPC47M292 and LPC47M997 are compatible for + hardware monitoring. + +Author: Hartmut Rick <linux@rick.claranet.de> + Special thanks to Jean Delvare for careful checking + of the code and many helpful comments and suggestions. + + +Description +----------- + +This driver implements support for the hardware sensor capabilities +of the SMSC LPC47M192 and compatible Super-I/O chips. + +These chips support 3 temperature channels and 8 voltage inputs +as well as CPU voltage VID input. + +They do also have fan monitoring and control capabilities, but the +these features are accessed via ISA bus and are not supported by this +driver. Use the 'smsc47m1' driver for fan monitoring and control. + +Voltages and temperatures are measured by an 8-bit ADC, the resolution +of the temperatures is 1 bit per degree C. +Voltages are scaled such that the nominal voltage corresponds to +192 counts, i.e. 3/4 of the full range. Thus the available range for +each voltage channel is 0V ... 255/192*(nominal voltage), the resolution +is 1 bit per (nominal voltage)/192. +Both voltage and temperature values are scaled by 1000, the sys files +show voltages in mV and temperatures in units of 0.001 degC. + +The +12V analog voltage input channel (in4_input) is multiplexed with +bit 4 of the encoded CPU voltage. This means that you either get +a +12V voltage measurement or a 5 bit CPU VID, but not both. +The default setting is to use the pin as 12V input, and use only 4 bit VID. +This driver assumes that the information in the configuration register +is correct, i.e. that the BIOS has updated the configuration if +the motherboard has this input wired to VID4. + +The temperature and voltage readings are updated once every 1.5 seconds. +Reading them more often repeats the same values. + + +sysfs interface +--------------- + +in0_input - +2.5V voltage input +in1_input - CPU voltage input (nominal 2.25V) +in2_input - +3.3V voltage input +in3_input - +5V voltage input +in4_input - +12V voltage input (may be missing if used as VID4) +in5_input - Vcc voltage input (nominal 3.3V) + This is the supply voltage of the sensor chip itself. +in6_input - +1.5V voltage input +in7_input - +1.8V voltage input + +in[0-7]_min, +in[0-7]_max - lower and upper alarm thresholds for in[0-7]_input reading + + All voltages are read and written in mV. + +in[0-7]_alarm - alarm flags for voltage inputs + These files read '1' in case of alarm, '0' otherwise. + +temp1_input - chip temperature measured by on-chip diode +temp[2-3]_input - temperature measured by external diodes (one of these would + typically be wired to the diode inside the CPU) + +temp[1-3]_min, +temp[1-3]_max - lower and upper alarm thresholds for temperatures + +temp[1-3]_offset - temperature offset registers + The chip adds the offsets stored in these registers to + the corresponding temperature readings. + Note that temp1 and temp2 offsets share the same register, + they cannot both be different from zero at the same time. + Writing a non-zero number to one of them will reset the other + offset to zero. + + All temperatures and offsets are read and written in + units of 0.001 degC. + +temp[1-3]_alarm - alarm flags for temperature inputs, '1' in case of alarm, + '0' otherwise. +temp[2-3]_input_fault - diode fault flags for temperature inputs 2 and 3. + A fault is detected if the two pins for the corresponding + sensor are open or shorted, or any of the two is shorted + to ground or Vcc. '1' indicates a diode fault. + +cpu0_vid - CPU voltage as received from the CPU + +vrm - CPU VID standard used for decoding CPU voltage + + The *_min, *_max, *_offset and vrm files can be read and + written, all others are read-only. diff --git a/Documentation/hwmon/submitting-patches b/Documentation/hwmon/submitting-patches new file mode 100644 index 00000000000..3d1bac399a2 --- /dev/null +++ b/Documentation/hwmon/submitting-patches @@ -0,0 +1,110 @@ + How to Get Your Patch Accepted Into the Hwmon Subsystem + ------------------------------------------------------- + +This text is a collection of suggestions for people writing patches or +drivers for the hwmon subsystem. Following these suggestions will greatly +increase the chances of your change being accepted. + + +1. General +---------- + +* It should be unnecessary to mention, but please read and follow + Documentation/SubmitChecklist + Documentation/SubmittingDrivers + Documentation/SubmittingPatches + Documentation/CodingStyle + +* If your patch generates checkpatch warnings, please refrain from explanations + such as "I don't like that coding style". Keep in mind that each unnecessary + warning helps hiding a real problem. If you don't like the kernel coding + style, don't write kernel drivers. + +* Please test your patch thoroughly. We are not your test group. + Sometimes a patch can not or not completely be tested because of missing + hardware. In such cases, you should test-build the code on at least one + architecture. If run-time testing was not achieved, it should be written + explicitly below the patch header. + +* If your patch (or the driver) is affected by configuration options such as + CONFIG_SMP, make sure it compiles for all configuration variants. + + +2. Adding functionality to existing drivers +------------------------------------------- + +* Make sure the documentation in Documentation/hwmon/<driver_name> is up to + date. + +* Make sure the information in Kconfig is up to date. + +* If the added functionality requires some cleanup or structural changes, split + your patch into a cleanup part and the actual addition. This makes it easier + to review your changes, and to bisect any resulting problems. + +* Never mix bug fixes, cleanup, and functional enhancements in a single patch. + + +3. New drivers +-------------- + +* Running your patch or driver file(s) through checkpatch does not mean its + formatting is clean. If unsure about formatting in your new driver, run it + through Lindent. Lindent is not perfect, and you may have to do some minor + cleanup, but it is a good start. + +* Consider adding yourself to MAINTAINERS. + +* Document the driver in Documentation/hwmon/<driver_name>. + +* Add the driver to Kconfig and Makefile in alphabetical order. + +* Make sure that all dependencies are listed in Kconfig. + +* Avoid forward declarations if you can. Rearrange the code if necessary. + +* Avoid calculations in macros and macro-generated functions. While such macros + may save a line or so in the source, it obfuscates the code and makes code + review more difficult. It may also result in code which is more complicated + than necessary. Use inline functions or just regular functions instead. + +* Use devres functions whenever possible to allocate resources. For rationale + and supported functions, please see Documentation/driver-model/devres.txt. + +* If the driver has a detect function, make sure it is silent. Debug messages + and messages printed after a successful detection are acceptable, but it + must not print messages such as "Chip XXX not found/supported". + + Keep in mind that the detect function will run for all drivers supporting an + address if a chip is detected on that address. Unnecessary messages will just + pollute the kernel log and not provide any value. + +* Provide a detect function if and only if a chip can be detected reliably. + +* Avoid writing to chip registers in the detect function. If you have to write, + only do it after you have already gathered enough data to be certain that the + detection is going to be successful. + + Keep in mind that the chip might not be what your driver believes it is, and + writing to it might cause a bad misconfiguration. + +* Make sure there are no race conditions in the probe function. Specifically, + completely initialize your chip first, then create sysfs entries and register + with the hwmon subsystem. + +* Do not provide support for deprecated sysfs attributes. + +* Do not create non-standard attributes unless really needed. If you have to use + non-standard attributes, or you believe you do, discuss it on the mailing list + first. Either case, provide a detailed explanation why you need the + non-standard attribute(s). + Standard attributes are specified in Documentation/hwmon/sysfs-interface. + +* When deciding which sysfs attributes to support, look at the chip's + capabilities. While we do not expect your driver to support everything the + chip may offer, it should at least support all limits and alarms. + +* Last but not least, please check if a driver for your chip already exists + before starting to write a new driver. Especially for temperature sensors, + new chips are often variants of previously released chips. In some cases, + a presumably new chip may simply have been relabeled. diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index 764cdc5480e..2cc95ad4660 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -2,17 +2,12 @@ Naming and data format standards for sysfs files ------------------------------------------------ The libsensors library offers an interface to the raw sensors data -through the sysfs interface. See libsensors documentation and source for -more further information. As of writing this document, libsensors -(from lm_sensors 2.8.3) is heavily chip-dependant. Adding or updating -support for any given chip requires modifying the library's code. -This is because libsensors was written for the procfs interface -older kernel modules were using, which wasn't standardized enough. -Recent versions of libsensors (from lm_sensors 2.8.2 and later) have -support for the sysfs interface, though. - -The new sysfs interface was designed to be as chip-independant as -possible. +through the sysfs interface. Since lm-sensors 3.0.0, libsensors is +completely chip-independent. It assumes that all the kernel drivers +implement the standard sysfs interface described in this document. +This makes adding or updating support for any given chip very easy, as +libsensors, and applications using it, do not need to be modified. +This is a major improvement compared to lm-sensors 2. Note that motherboards vary widely in the connections to sensor chips. There is no standard that ensures, for example, that the second @@ -24,7 +19,7 @@ range using external resistors. Since the values of these resistors can change from motherboard to motherboard, the conversions cannot be hard coded into the driver and have to be done in user space. -For this reason, even if we aim at a chip-independant libsensors, it will +For this reason, even if we aim at a chip-independent libsensors, it will still require a configuration file (e.g. /etc/sensors.conf) for proper values conversion, labeling of inputs and hiding of unused inputs. @@ -35,19 +30,18 @@ access this data in a simple and consistent way. That said, such programs will have to implement conversion, labeling and hiding of inputs. For this reason, it is still not recommended to bypass the library. -If you are developing a userspace application please send us feedback on -this standard. - -Note that this standard isn't completely established yet, so it is subject -to changes, even important ones. One more reason to use the library instead -of accessing sysfs files directly. - Each chip gets its own directory in the sysfs /sys/devices tree. To -find all sensor chips, it is easier to follow the symlinks from -/sys/i2c/devices/ +find all sensor chips, it is easier to follow the device symlinks from +/sys/class/hwmon/hwmon*. + +Up to lm-sensors 3.0.0, libsensors looks for hardware monitoring attributes +in the "physical" device directory. Since lm-sensors 3.0.1, attributes found +in the hwmon "class" device directory are also supported. Complex drivers +(e.g. drivers for multifunction chips) may want to use this possibility to +avoid namespace pollution. The only drawback will be that older versions of +libsensors won't support the driver in question. -All sysfs values are fixed point numbers. To get the true value of some -of the values, you should divide by the specified value. +All sysfs values are fixed point numbers. There is only one value per file, unlike the older /proc specification. The common scheme for files naming is: <type><number>_<item>. Usual @@ -66,96 +60,216 @@ between readings to be caught and alarmed. The exact definition of an alarm (for example, whether a threshold must be met or must be exceeded to cause an alarm) is chip-dependent. +When setting values of hwmon sysfs attributes, the string representation of +the desired value must be written, note that strings which are not a number +are interpreted as 0! For more on how written strings are interpreted see the +"sysfs attribute writes interpretation" section at the end of this file. ------------------------------------------------------------------------- +[0-*] denotes any positive number starting from 0 +[1-*] denotes any positive number starting from 1 +RO read only value +WO write only value +RW read/write value + +Read/write values may be read-only for some chips, depending on the +hardware implementation. + +All entries (except name) are optional, and should only be created in a +given driver if the chip has the feature. + + +********************* +* Global attributes * +********************* + +name The chip name. + This should be a short, lowercase string, not containing + spaces nor dashes, representing the chip name. This is + the only mandatory attribute. + I2C devices get this attribute created automatically. + RO + +update_interval The interval at which the chip will update readings. + Unit: millisecond + RW + Some devices have a variable update rate or interval. + This attribute can be used to change it to the desired value. + + ************ * Voltages * ************ -in[0-8]_min Voltage min value. +in[0-*]_min Voltage min value. Unit: millivolt - Read/Write + RW -in[0-8]_max Voltage max value. +in[0-*]_lcrit Voltage critical min value. Unit: millivolt - Read/Write + RW + If voltage drops to or below this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + +in[0-*]_max Voltage max value. + Unit: millivolt + RW -in[0-8]_input Voltage input value. +in[0-*]_crit Voltage critical max value. Unit: millivolt - Read only + RW + If voltage reaches or exceeds this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + +in[0-*]_input Voltage input value. + Unit: millivolt + RO + Voltage measured on the chip pin. Actual voltage depends on the scaling resistors on the motherboard, as recommended in the chip datasheet. This varies by chip and by motherboard. Because of this variation, values are generally NOT scaled by the chip driver, and must be done by the application. However, some drivers (notably lm87 and via686a) - do scale, with various degrees of success. - These drivers will output the actual voltage. - - Typical usage: - in0_* CPU #1 voltage (not scaled) - in1_* CPU #2 voltage (not scaled) - in2_* 3.3V nominal (not scaled) - in3_* 5.0V nominal (scaled) - in4_* 12.0V nominal (scaled) - in5_* -12.0V nominal (scaled) - in6_* -5.0V nominal (scaled) - in7_* varies - in8_* varies - -cpu[0-1]_vid CPU core reference voltage. + do scale, because of internal resistors built into a chip. + These drivers will output the actual voltage. Rule of + thumb: drivers should report the voltage values at the + "pins" of the chip. + +in[0-*]_average + Average voltage + Unit: millivolt + RO + +in[0-*]_lowest + Historical minimum voltage + Unit: millivolt + RO + +in[0-*]_highest + Historical maximum voltage + Unit: millivolt + RO + +in[0-*]_reset_history + Reset inX_lowest and inX_highest + WO + +in_reset_history + Reset inX_lowest and inX_highest for all sensors + WO + +in[0-*]_label Suggested voltage channel label. + Text string + Should only be created if the driver has hints about what + this voltage channel is being used for, and user-space + doesn't. In all other cases, the label is provided by + user-space. + RO + +cpu[0-*]_vid CPU core reference voltage. Unit: millivolt - Read only. + RO Not always correct. vrm Voltage Regulator Module version number. - Read only. - Two digit number, first is major version, second is - minor version. + RW (but changing it should no more be necessary) + Originally the VRM standard version multiplied by 10, but now + an arbitrary number, as not all standards have a version + number. Affects the way the driver calculates the CPU core reference voltage from the vid pins. +Also see the Alarms section for status flags associated with voltages. + ******** * Fans * ******** -fan[1-3]_min Fan minimum value +fan[1-*]_min Fan minimum value Unit: revolution/min (RPM) - Read/Write. + RW -fan[1-3]_input Fan input value. +fan[1-*]_max Fan maximum value Unit: revolution/min (RPM) - Read only. + Only rarely supported by the hardware. + RW -fan[1-3]_div Fan divisor. +fan[1-*]_input Fan input value. + Unit: revolution/min (RPM) + RO + +fan[1-*]_div Fan divisor. Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128). + RW Some chips only support values 1, 2, 4 and 8. Note that this is actually an internal clock divisor, which affects the measurable speed range, not the read value. +fan[1-*]_pulses Number of tachometer pulses per fan revolution. + Integer value, typically between 1 and 4. + RW + This value is a characteristic of the fan connected to the + device's input, so it has to be set in accordance with the fan + model. + Should only be created if the chip has a register to configure + the number of pulses. In the absence of such a register (and + thus attribute) the value assumed by all devices is 2 pulses + per fan revolution. + +fan[1-*]_target + Desired fan speed + Unit: revolution/min (RPM) + RW + Only makes sense if the chip supports closed-loop fan speed + control based on the measured fan speed. + +fan[1-*]_label Suggested fan channel label. + Text string + Should only be created if the driver has hints about what + this fan channel is being used for, and user-space doesn't. + In all other cases, the label is provided by user-space. + RO + +Also see the Alarms section for status flags associated with fans. + + ******* * PWM * ******* -pwm[1-3] Pulse width modulation fan control. +pwm[1-*] Pulse width modulation fan control. Integer value in the range 0 to 255 - Read/Write + RW 255 is max or 100%. -pwm[1-3]_enable - Switch PWM on and off. - Not always present even if fan*_pwm is. - 0 to turn off - 1 to turn on in manual mode - 2 to turn on in automatic mode - Read/Write +pwm[1-*]_enable + Fan speed control method: + 0: no fan speed control (i.e. fan at full speed) + 1: manual fan speed control enabled (using pwm[1-*]) + 2+: automatic fan speed control enabled + Check individual chip documentation files for automatic mode + details. + RW + +pwm[1-*]_mode 0: DC mode (direct current) + 1: PWM mode (pulse-width modulation) + RW + +pwm[1-*]_freq Base PWM frequency in Hz. + Only possibly available when pwmN_mode is PWM, but not always + present even then. + RW pwm[1-*]_auto_channels_temp Select which temperature channels affect this PWM output in auto mode. Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc... Which values are possible depend on the chip used. + RW pwm[1-*]_auto_point[1-*]_pwm pwm[1-*]_auto_point[1-*]_temp @@ -163,8 +277,7 @@ pwm[1-*]_auto_point[1-*]_temp_hyst Define the PWM vs temperature curve. Number of trip points is chip-dependent. Use this for chips which associate trip points to PWM output channels. - -OR + RW temp[1-*]_auto_point[1-*]_pwm temp[1-*]_auto_point[1-*]_temp @@ -172,85 +285,389 @@ temp[1-*]_auto_point[1-*]_temp_hyst Define the PWM vs temperature curve. Number of trip points is chip-dependent. Use this for chips which associate trip points to temperature channels. + RW + +There is a third case where trip points are associated to both PWM output +channels and temperature channels: the PWM values are associated to PWM +output channels while the temperature values are associated to temperature +channels. In that case, the result is determined by the mapping between +temperature inputs and PWM outputs. When several temperature inputs are +mapped to a given PWM output, this leads to several candidate PWM values. +The actual result is up to the chip, but in general the highest candidate +value (fastest fan speed) wins. **************** * Temperatures * **************** -temp[1-3]_type Sensor type selection. - Integers 1, 2, 3 or thermistor Beta value (3435) - Read/Write. - 1: PII/Celeron Diode +temp[1-*]_type Sensor type selection. + Integers 1 to 6 + RW + 1: CPU embedded diode 2: 3904 transistor 3: thermal diode + 4: thermistor + 5: AMD AMDSI + 6: Intel PECI Not all types are supported by all chips -temp[1-4]_max Temperature max value. - Unit: millidegree Celcius - Read/Write value. +temp[1-*]_max Temperature max value. + Unit: millidegree Celsius (or millivolt, see below) + RW -temp[1-3]_min Temperature min value. - Unit: millidegree Celcius - Read/Write value. +temp[1-*]_min Temperature min value. + Unit: millidegree Celsius + RW -temp[1-3]_max_hyst +temp[1-*]_max_hyst Temperature hysteresis value for max limit. - Unit: millidegree Celcius + Unit: millidegree Celsius Must be reported as an absolute temperature, NOT a delta from the max value. - Read/Write value. + RW -temp[1-4]_input Temperature input value. - Unit: millidegree Celcius - Read only value. +temp[1-*]_min_hyst + Temperature hysteresis value for min limit. + Unit: millidegree Celsius + Must be reported as an absolute temperature, NOT a delta + from the min value. + RW -temp[1-4]_crit Temperature critical value, typically greater than +temp[1-*]_input Temperature input value. + Unit: millidegree Celsius + RO + +temp[1-*]_crit Temperature critical max value, typically greater than corresponding temp_max values. - Unit: millidegree Celcius - Read/Write value. + Unit: millidegree Celsius + RW -temp[1-2]_crit_hyst +temp[1-*]_crit_hyst Temperature hysteresis value for critical limit. - Unit: millidegree Celcius + Unit: millidegree Celsius Must be reported as an absolute temperature, NOT a delta from the critical value. + RW + +temp[1-*]_emergency + Temperature emergency max value, for chips supporting more than + two upper temperature limits. Must be equal or greater than + corresponding temp_crit values. + Unit: millidegree Celsius + RW + +temp[1-*]_emergency_hyst + Temperature hysteresis value for emergency limit. + Unit: millidegree Celsius + Must be reported as an absolute temperature, NOT a delta + from the emergency value. + RW + +temp[1-*]_lcrit Temperature critical min value, typically lower than + corresponding temp_min values. + Unit: millidegree Celsius + RW + +temp[1-*]_lcrit_hyst + Temperature hysteresis value for critical min limit. + Unit: millidegree Celsius + Must be reported as an absolute temperature, NOT a delta + from the critical min value. + RW + +temp[1-*]_offset + Temperature offset which is added to the temperature reading + by the chip. + Unit: millidegree Celsius Read/Write value. - If there are multiple temperature sensors, temp1_* is - generally the sensor inside the chip itself, - reported as "motherboard temperature". temp2_* to - temp4_* are generally sensors external to the chip - itself, for example the thermal diode inside the CPU or - a thermistor nearby. +temp[1-*]_label Suggested temperature channel label. + Text string + Should only be created if the driver has hints about what + this temperature channel is being used for, and user-space + doesn't. In all other cases, the label is provided by + user-space. + RO + +temp[1-*]_lowest + Historical minimum temperature + Unit: millidegree Celsius + RO + +temp[1-*]_highest + Historical maximum temperature + Unit: millidegree Celsius + RO + +temp[1-*]_reset_history + Reset temp_lowest and temp_highest + WO + +temp_reset_history + Reset temp_lowest and temp_highest for all sensors + WO + +Some chips measure temperature using external thermistors and an ADC, and +report the temperature measurement as a voltage. Converting this voltage +back to a temperature (or the other way around for limits) requires +mathematical functions not available in the kernel, so the conversion +must occur in user space. For these chips, all temp* files described +above should contain values expressed in millivolt instead of millidegree +Celsius. In other words, such temperature channels are handled as voltage +channels by the driver. + +Also see the Alarms section for status flags associated with temperatures. ************ * Currents * ************ -Note that no known chip provides current measurements as of writing, -so this part is theoretical, so to say. +curr[1-*]_max Current max value + Unit: milliampere + RW + +curr[1-*]_min Current min value. + Unit: milliampere + RW + +curr[1-*]_lcrit Current critical low value + Unit: milliampere + RW -curr[1-n]_max Current max value +curr[1-*]_crit Current critical high value. Unit: milliampere - Read/Write. + RW -curr[1-n]_min Current min value. +curr[1-*]_input Current input value Unit: milliampere - Read/Write. + RO -curr[1-n]_input Current input value +curr[1-*]_average + Average current use Unit: milliampere - Read only. + RO +curr[1-*]_lowest + Historical minimum current + Unit: milliampere + RO + +curr[1-*]_highest + Historical maximum current + Unit: milliampere + RO + +curr[1-*]_reset_history + Reset currX_lowest and currX_highest + WO + +curr_reset_history + Reset currX_lowest and currX_highest for all sensors + WO + +Also see the Alarms section for status flags associated with currents. ********* -* Other * +* Power * ********* +power[1-*]_average Average power use + Unit: microWatt + RO + +power[1-*]_average_interval Power use averaging interval. A poll + notification is sent to this file if the + hardware changes the averaging interval. + Unit: milliseconds + RW + +power[1-*]_average_interval_max Maximum power use averaging interval + Unit: milliseconds + RO + +power[1-*]_average_interval_min Minimum power use averaging interval + Unit: milliseconds + RO + +power[1-*]_average_highest Historical average maximum power use + Unit: microWatt + RO + +power[1-*]_average_lowest Historical average minimum power use + Unit: microWatt + RO + +power[1-*]_average_max A poll notification is sent to + power[1-*]_average when power use + rises above this value. + Unit: microWatt + RW + +power[1-*]_average_min A poll notification is sent to + power[1-*]_average when power use + sinks below this value. + Unit: microWatt + RW + +power[1-*]_input Instantaneous power use + Unit: microWatt + RO + +power[1-*]_input_highest Historical maximum power use + Unit: microWatt + RO + +power[1-*]_input_lowest Historical minimum power use + Unit: microWatt + RO + +power[1-*]_reset_history Reset input_highest, input_lowest, + average_highest and average_lowest. + WO + +power[1-*]_accuracy Accuracy of the power meter. + Unit: Percent + RO + +power[1-*]_cap If power use rises above this limit, the + system should take action to reduce power use. + A poll notification is sent to this file if the + cap is changed by the hardware. The *_cap + files only appear if the cap is known to be + enforced by hardware. + Unit: microWatt + RW + +power[1-*]_cap_hyst Margin of hysteresis built around capping and + notification. + Unit: microWatt + RW + +power[1-*]_cap_max Maximum cap that can be set. + Unit: microWatt + RO + +power[1-*]_cap_min Minimum cap that can be set. + Unit: microWatt + RO + +power[1-*]_max Maximum power. + Unit: microWatt + RW + +power[1-*]_crit Critical maximum power. + If power rises to or above this limit, the + system is expected take drastic action to reduce + power consumption, such as a system shutdown or + a forced powerdown of some devices. + Unit: microWatt + RW + +Also see the Alarms section for status flags associated with power readings. + +********** +* Energy * +********** + +energy[1-*]_input Cumulative energy use + Unit: microJoule + RO + + +************ +* Humidity * +************ + +humidity[1-*]_input Humidity + Unit: milli-percent (per cent mille, pcm) + RO + + +********** +* Alarms * +********** + +Each channel or limit may have an associated alarm file, containing a +boolean value. 1 means than an alarm condition exists, 0 means no alarm. + +Usually a given chip will either use channel-related alarms, or +limit-related alarms, not both. The driver should just reflect the hardware +implementation. + +in[0-*]_alarm +curr[1-*]_alarm +power[1-*]_alarm +fan[1-*]_alarm +temp[1-*]_alarm + Channel alarm + 0: no alarm + 1: alarm + RO + +OR + +in[0-*]_min_alarm +in[0-*]_max_alarm +in[0-*]_lcrit_alarm +in[0-*]_crit_alarm +curr[1-*]_min_alarm +curr[1-*]_max_alarm +curr[1-*]_lcrit_alarm +curr[1-*]_crit_alarm +power[1-*]_cap_alarm +power[1-*]_max_alarm +power[1-*]_crit_alarm +fan[1-*]_min_alarm +fan[1-*]_max_alarm +temp[1-*]_min_alarm +temp[1-*]_max_alarm +temp[1-*]_lcrit_alarm +temp[1-*]_crit_alarm +temp[1-*]_emergency_alarm + Limit alarm + 0: no alarm + 1: alarm + RO + +Each input channel may have an associated fault file. This can be used +to notify open diodes, unconnected fans etc. where the hardware +supports it. When this boolean has value 1, the measurement for that +channel should not be trusted. + +fan[1-*]_fault +temp[1-*]_fault + Input fault condition + 0: no fault occurred + 1: fault condition + RO + +Some chips also offer the possibility to get beeped when an alarm occurs: + +beep_enable Master beep enable + 0: no beeps + 1: beeps + RW + +in[0-*]_beep +curr[1-*]_beep +fan[1-*]_beep +temp[1-*]_beep + Channel beep + 0: disable + 1: enable + RW + +In theory, a chip could provide per-limit beep masking, but no such chip +was seen so far. + +Old drivers provided a different, non-standard interface to alarms and +beeps. These interface files are deprecated, but will be kept around +for compatibility reasons: + alarms Alarm bitmask. - Read only. + RO Integer representation of one to four bytes. A '1' bit means an alarm. Chips should be programmed for 'comparator' mode so that @@ -258,20 +675,86 @@ alarms Alarm bitmask. if it is still valid. Generally a direct representation of a chip's internal alarm registers; there is no standard for the position - of individual bits. + of individual bits. For this reason, the use of this + interface file for new drivers is discouraged. Use + individual *_alarm and *_fault files instead. Bits are defined in kernel/include/sensors.h. -beep_enable Beep/interrupt enable - 0 to disable. - 1 to enable. - Read/Write - beep_mask Bitmask for beep. - Same format as 'alarms' with the same bit locations. - Read/Write - -eeprom Raw EEPROM data in binary form. - Read only. - -pec Enable or disable PEC (SMBus only) - Read/Write + Same format as 'alarms' with the same bit locations, + use discouraged for the same reason. Use individual + *_beep files instead. + RW + + +*********************** +* Intrusion detection * +*********************** + +intrusion[0-*]_alarm + Chassis intrusion detection + 0: OK + 1: intrusion detected + RW + Contrary to regular alarm flags which clear themselves + automatically when read, this one sticks until cleared by + the user. This is done by writing 0 to the file. Writing + other values is unsupported. + +intrusion[0-*]_beep + Chassis intrusion beep + 0: disable + 1: enable + RW + + +sysfs attribute writes interpretation +------------------------------------- + +hwmon sysfs attributes always contain numbers, so the first thing to do is to +convert the input to a number, there are 2 ways todo this depending whether +the number can be negative or not: +unsigned long u = simple_strtoul(buf, NULL, 10); +long s = simple_strtol(buf, NULL, 10); + +With buf being the buffer with the user input being passed by the kernel. +Notice that we do not use the second argument of strto[u]l, and thus cannot +tell when 0 is returned, if this was really 0 or is caused by invalid input. +This is done deliberately as checking this everywhere would add a lot of +code to the kernel. + +Notice that it is important to always store the converted value in an +unsigned long or long, so that no wrap around can happen before any further +checking. + +After the input string is converted to an (unsigned) long, the value should be +checked if its acceptable. Be careful with further conversions on the value +before checking it for validity, as these conversions could still cause a wrap +around before the check. For example do not multiply the result, and only +add/subtract if it has been divided before the add/subtract. + +What to do if a value is found to be invalid, depends on the type of the +sysfs attribute that is being set. If it is a continuous setting like a +tempX_max or inX_max attribute, then the value should be clamped to its +limits using clamp_val(value, min_limit, max_limit). If it is not continuous +like for example a tempX_type, then when an invalid value is written, +-EINVAL should be returned. + +Example1, temp1_max, register is a signed 8 bit value (-128 - 127 degrees): + + long v = simple_strtol(buf, NULL, 10) / 1000; + v = clamp_val(v, -128, 127); + /* write v to register */ + +Example2, fan divider setting, valid values 2, 4 and 8: + + unsigned long v = simple_strtoul(buf, NULL, 10); + + switch (v) { + case 2: v = 1; break; + case 4: v = 2; break; + case 8: v = 3; break; + default: + return -EINVAL; + } + /* write v to register */ diff --git a/Documentation/hwmon/thmc50 b/Documentation/hwmon/thmc50 new file mode 100644 index 00000000000..8a7772ade8d --- /dev/null +++ b/Documentation/hwmon/thmc50 @@ -0,0 +1,74 @@ +Kernel driver thmc50 +===================== + +Supported chips: + * Analog Devices ADM1022 + Prefix: 'adm1022' + Addresses scanned: I2C 0x2c - 0x2e + Datasheet: http://www.analog.com/en/prod/0,2877,ADM1022,00.html + * Texas Instruments THMC50 + Prefix: 'thmc50' + Addresses scanned: I2C 0x2c - 0x2e + Datasheet: http://www.ti.com/ + +Author: Krzysztof Helt <krzysztof.h1@wp.pl> + +This driver was derived from the 2.4 kernel thmc50.c source file. + +Credits: + thmc50.c (2.4 kernel): + Frodo Looijaard <frodol@dds.nl> + Philip Edelbrock <phil@netroedge.com> + +Module Parameters +----------------- + +* adm1022_temp3: short array + List of adapter,address pairs to force chips into ADM1022 mode with + second remote temperature. This does not work for original THMC50 chips. + +Description +----------- + +The THMC50 implements: an internal temperature sensor, support for an +external diode-type temperature sensor (compatible w/ the diode sensor inside +many processors), and a controllable fan/analog_out DAC. For the temperature +sensors, limits can be set through the appropriate Overtemperature Shutdown +register and Hysteresis register. Each value can be set and read to half-degree +accuracy. An alarm is issued (usually to a connected LM78) when the +temperature gets higher then the Overtemperature Shutdown value; it stays on +until the temperature falls below the Hysteresis value. All temperatures are in +degrees Celsius, and are guaranteed within a range of -55 to +125 degrees. + +The THMC50 only updates its values each 1.5 seconds; reading it more often +will do no harm, but will return 'old' values. + +The THMC50 is usually used in combination with LM78-like chips, to measure +the temperature of the processor(s). + +The ADM1022 works the same as THMC50 but it is faster (5 Hz instead of +1 Hz for THMC50). It can be also put in a new mode to handle additional +remote temperature sensor. The driver use the mode set by BIOS by default. + +In case the BIOS is broken and the mode is set incorrectly, you can force +the mode with additional remote temperature with adm1022_temp3 parameter. +A typical symptom of wrong setting is a fan forced to full speed. + +Driver Features +--------------- + +The driver provides up to three temperatures: + +temp1 -- internal +temp2 -- remote +temp3 -- 2nd remote only for ADM1022 + +pwm1 -- fan speed (0 = stop, 255 = full) +pwm1_mode -- always 0 (DC mode) + +The value of 0 for pwm1 also forces FAN_OFF signal from the chip, +so it stops fans even if the value 0 into the ANALOG_OUT register does not. + +The driver was tested on Compaq AP550 with two ADM1022 chips (one works +in the temp3 mode), five temperature readings and two fans. + diff --git a/Documentation/hwmon/tmp102 b/Documentation/hwmon/tmp102 new file mode 100644 index 00000000000..8454a776312 --- /dev/null +++ b/Documentation/hwmon/tmp102 @@ -0,0 +1,26 @@ +Kernel driver tmp102 +==================== + +Supported chips: + * Texas Instruments TMP102 + Prefix: 'tmp102' + Addresses scanned: none + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp102.html + +Author: + Steven King <sfking@fdwdc.com> + +Description +----------- + +The Texas Instruments TMP102 implements one temperature sensor. Limits can be +set through the Overtemperature Shutdown register and Hysteresis register. The +sensor is accurate to 0.5 degree over the range of -25 to +85 C, and to 1.0 +degree from -40 to +125 C. Resolution of the sensor is 0.0625 degree. The +operating temperature has a minimum of -55 C and a maximum of +150 C. + +The TMP102 has a programmable update rate that can select between 8, 4, 1, and +0.5 Hz. (Currently the driver only supports the default of 4 Hz). + +The driver provides the common sysfs-interface for temperatures (see +Documentation/hwmon/sysfs-interface under Temperatures). diff --git a/Documentation/hwmon/tmp401 b/Documentation/hwmon/tmp401 new file mode 100644 index 00000000000..f91e3fa7e5e --- /dev/null +++ b/Documentation/hwmon/tmp401 @@ -0,0 +1,53 @@ +Kernel driver tmp401 +==================== + +Supported chips: + * Texas Instruments TMP401 + Prefix: 'tmp401' + Addresses scanned: I2C 0x4c + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp401.html + * Texas Instruments TMP411 + Prefix: 'tmp411' + Addresses scanned: I2C 0x4c, 0x4d, 0x4e + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp411.html + * Texas Instruments TMP431 + Prefix: 'tmp431' + Addresses scanned: I2C 0x4c, 0x4d + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp431.html + * Texas Instruments TMP432 + Prefix: 'tmp432' + Addresses scanned: I2C 0x4c, 0x4d + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp432.html + +Authors: + Hans de Goede <hdegoede@redhat.com> + Andre Prendel <andre.prendel@gmx.de> + +Description +----------- + +This driver implements support for Texas Instruments TMP401, TMP411, +TMP431, and TMP432 chips. These chips implement one or two remote and +one local temperature sensors. Temperature is measured in degrees +Celsius. Resolution of the remote sensor is 0.0625 degree. Local +sensor resolution can be set to 0.5, 0.25, 0.125 or 0.0625 degree (not +supported by the driver so far, so using the default resolution of 0.5 +degree). + +The driver provides the common sysfs-interface for temperatures (see +Documentation/hwmon/sysfs-interface under Temperatures). + +The TMP411 and TMP431 chips are compatible with TMP401. TMP411 provides +some additional features. + +* Minimum and Maximum temperature measured since power-on, chip-reset + + Exported via sysfs attributes tempX_lowest and tempX_highest. + +* Reset of historical minimum/maximum temperature measurements + + Exported via sysfs attribute temp_reset_history. Writing 1 to this + file triggers a reset. + +TMP432 is compatible with TMP401 and TMP431. It supports two external +temperature sensors. diff --git a/Documentation/hwmon/tmp421 b/Documentation/hwmon/tmp421 new file mode 100644 index 00000000000..0cf07f82474 --- /dev/null +++ b/Documentation/hwmon/tmp421 @@ -0,0 +1,36 @@ +Kernel driver tmp421 +==================== + +Supported chips: + * Texas Instruments TMP421 + Prefix: 'tmp421' + Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html + * Texas Instruments TMP422 + Prefix: 'tmp422' + Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html + * Texas Instruments TMP423 + Prefix: 'tmp423' + Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f + Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html + +Authors: + Andre Prendel <andre.prendel@gmx.de> + +Description +----------- + +This driver implements support for Texas Instruments TMP421, TMP422 +and TMP423 temperature sensor chips. These chips implement one local +and up to one (TMP421), up to two (TMP422) or up to three (TMP423) +remote sensors. Temperature is measured in degrees Celsius. The chips +are wired over I2C/SMBus and specified over a temperature range of -40 +to +125 degrees Celsius. Resolution for both the local and remote +channels is 0.0625 degree C. + +The chips support only temperature measurement. The driver exports +the temperature values via the following sysfs files: + +temp[1-4]_input +temp[2-4]_fault diff --git a/Documentation/hwmon/twl4030-madc-hwmon b/Documentation/hwmon/twl4030-madc-hwmon new file mode 100644 index 00000000000..c3a3a5be10a --- /dev/null +++ b/Documentation/hwmon/twl4030-madc-hwmon @@ -0,0 +1,45 @@ +Kernel driver twl4030-madc +========================= + +Supported chips: + * Texas Instruments TWL4030 + Prefix: 'twl4030-madc' + + +Authors: + J Keerthy <j-keerthy@ti.com> + +Description +----------- + +The Texas Instruments TWL4030 is a Power Management and Audio Circuit. Among +other things it contains a 10-bit A/D converter MADC. The converter has 16 +channels which can be used in different modes. + + +See this table for the meaning of the different channels + +Channel Signal +------------------------------------------ +0 Battery type(BTYPE) +1 BCI: Battery temperature (BTEMP) +2 GP analog input +3 GP analog input +4 GP analog input +5 GP analog input +6 GP analog input +7 GP analog input +8 BCI: VBUS voltage(VBUS) +9 Backup Battery voltage (VBKP) +10 BCI: Battery charger current (ICHG) +11 BCI: Battery charger voltage (VCHG) +12 BCI: Main battery voltage (VBAT) +13 Reserved +14 Reserved +15 VRUSB Supply/Speaker left/Speaker right polarization level + + +The Sysfs nodes will represent the voltage in the units of mV, +the temperature channel shows the converted temperature in +degree Celsius. The Battery charging current channel represents +battery charging current in mA. diff --git a/Documentation/hwmon/ucd9000 b/Documentation/hwmon/ucd9000 new file mode 100644 index 00000000000..805e33edb97 --- /dev/null +++ b/Documentation/hwmon/ucd9000 @@ -0,0 +1,110 @@ +Kernel driver ucd9000 +===================== + +Supported chips: + * TI UCD90120, UCD90124, UCD9090, and UCD90910 + Prefixes: 'ucd90120', 'ucd90124', 'ucd9090', 'ucd90910' + Addresses scanned: - + Datasheets: + http://focus.ti.com/lit/ds/symlink/ucd90120.pdf + http://focus.ti.com/lit/ds/symlink/ucd90124.pdf + http://focus.ti.com/lit/ds/symlink/ucd9090.pdf + http://focus.ti.com/lit/ds/symlink/ucd90910.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +From datasheets: + +The UCD90120 Power Supply Sequencer and System Health Monitor monitors and +sequences up to 12 independent voltage rails. The device integrates a 12-bit +ADC with a 2.5V internal reference for monitoring up to 13 power supply voltage, +current, or temperature inputs. + +The UCD90124 is a 12-rail PMBus/I2C addressable power-supply sequencer and +system-health monitor. The device integrates a 12-bit ADC for monitoring up to +13 power-supply voltage, current, or temperature inputs. Twenty-six GPIO pins +can be used for power supply enables, power-on reset signals, external +interrupts, cascading, or other system functions. Twelve of these pins offer PWM +functionality. Using these pins, the UCD90124 offers support for fan control, +margining, and general-purpose PWM functions. + +The UCD9090 is a 10-rail PMBus/I2C addressable power-supply sequencer and +monitor. The device integrates a 12-bit ADC for monitoring up to 10 power-supply +voltage inputs. Twenty-three GPIO pins can be used for power supply enables, +power-on reset signals, external interrupts, cascading, or other system +functions. Ten of these pins offer PWM functionality. Using these pins, the +UCD9090 offers support for margining, and general-purpose PWM functions. + +The UCD90910 is a ten-rail I2C / PMBus addressable power-supply sequencer and +system-health monitor. The device integrates a 12-bit ADC for monitoring up to +13 power-supply voltage, current, or temperature inputs. + +This driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. Please see +Documentation/hwmon/pmbus for details. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-12]_label "vout[1-12]". +in[1-12]_input Measured voltage. From READ_VOUT register. +in[1-12]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-12]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-12]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-12]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-12]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-12]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-12]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-12]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr[1-12]_label "iout[1-12]". +curr[1-12]_input Measured current. From READ_IOUT register. +curr[1-12]_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr[1-12]_lcrit Critical minimum output current. From IOUT_UC_FAULT_LIMIT + register. +curr[1-12]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr[1-12]_max_alarm Current high alarm. From IOUT_OC_WARNING status. +curr[1-12]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + + For each attribute index, either voltage or current is + reported, but not both. If voltage or current is + reported depends on the chip configuration. + +temp[1-2]_input Measured temperatures. From READ_TEMPERATURE_1 and + READ_TEMPERATURE_2 registers. +temp[1-2]_max Maximum temperature. From OT_WARN_LIMIT register. +temp[1-2]_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp[1-2]_max_alarm Temperature high alarm. +temp[1-2]_crit_alarm Temperature critical high alarm. + +fan[1-4]_input Fan RPM. +fan[1-4]_alarm Fan alarm. +fan[1-4]_fault Fan fault. + + Fan attributes are only available on chips supporting + fan control (UCD90124, UCD90910). Attribute files are + created only for enabled fans. + Note that even though UCD90910 supports up to 10 fans, + only up to four fans are currently supported. diff --git a/Documentation/hwmon/ucd9200 b/Documentation/hwmon/ucd9200 new file mode 100644 index 00000000000..1e8060e631b --- /dev/null +++ b/Documentation/hwmon/ucd9200 @@ -0,0 +1,112 @@ +Kernel driver ucd9200 +===================== + +Supported chips: + * TI UCD9220, UCD9222, UCD9224, UCD9240, UCD9244, UCD9246, and UCD9248 + Prefixes: 'ucd9220', 'ucd9222', 'ucd9224', 'ucd9240', 'ucd9244', 'ucd9246', + 'ucd9248' + Addresses scanned: - + Datasheets: + http://focus.ti.com/lit/ds/symlink/ucd9220.pdf + http://focus.ti.com/lit/ds/symlink/ucd9222.pdf + http://focus.ti.com/lit/ds/symlink/ucd9224.pdf + http://focus.ti.com/lit/ds/symlink/ucd9240.pdf + http://focus.ti.com/lit/ds/symlink/ucd9244.pdf + http://focus.ti.com/lit/ds/symlink/ucd9246.pdf + http://focus.ti.com/lit/ds/symlink/ucd9248.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +[From datasheets] UCD9220, UCD9222, UCD9224, UCD9240, UCD9244, UCD9246, and +UCD9248 are multi-rail, multi-phase synchronous buck digital PWM controllers +designed for non-isolated DC/DC power applications. The devices integrate +dedicated circuitry for DC/DC loop management with flash memory and a serial +interface to support configuration, monitoring and management. + +This driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. Please see +Documentation/hwmon/pmbus for details. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vin". +in1_input Measured voltage. From READ_VIN register. +in1_min Minimum Voltage. From VIN_UV_WARN_LIMIT register. +in1_max Maximum voltage. From VIN_OV_WARN_LIMIT register. +in1_lcrit Critical minimum Voltage. VIN_UV_FAULT_LIMIT register. +in1_crit Critical maximum voltage. From VIN_OV_FAULT_LIMIT register. +in1_min_alarm Voltage low alarm. From VIN_UV_WARNING status. +in1_max_alarm Voltage high alarm. From VIN_OV_WARNING status. +in1_lcrit_alarm Voltage critical low alarm. From VIN_UV_FAULT status. +in1_crit_alarm Voltage critical high alarm. From VIN_OV_FAULT status. + +in[2-5]_label "vout[1-4]". +in[2-5]_input Measured voltage. From READ_VOUT register. +in[2-5]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register. +in[2-5]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[2-5]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register. +in[2-5]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[2-5]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[2-5]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[2-5]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[2-5]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr1_label "iin". +curr1_input Measured current. From READ_IIN register. + +curr[2-5]_label "iout[1-4]". +curr[2-5]_input Measured current. From READ_IOUT register. +curr[2-5]_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr[2-5]_lcrit Critical minimum output current. From IOUT_UC_FAULT_LIMIT + register. +curr[2-5]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr[2-5]_max_alarm Current high alarm. From IOUT_OC_WARNING status. +curr[2-5]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + +power1_input Measured input power. From READ_PIN register. +power1_label "pin" + +power[2-5]_input Measured output power. From READ_POUT register. +power[2-5]_label "pout[1-4]" + + The number of output voltage, current, and power + attribute sets is determined by the number of enabled + rails. See chip datasheets for details. + +temp[1-5]_input Measured temperatures. From READ_TEMPERATURE_1 and + READ_TEMPERATURE_2 registers. + temp1 is the chip internal temperature. temp[2-5] are + rail temperatures. temp[2-5] attributes are only + created for enabled rails. See chip datasheets for + details. +temp[1-5]_max Maximum temperature. From OT_WARN_LIMIT register. +temp[1-5]_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp[1-5]_max_alarm Temperature high alarm. +temp[1-5]_crit_alarm Temperature critical high alarm. + +fan1_input Fan RPM. ucd9240 only. +fan1_alarm Fan alarm. ucd9240 only. +fan1_fault Fan fault. ucd9240 only. diff --git a/Documentation/hwmon/userspace-tools b/Documentation/hwmon/userspace-tools index 2622aac6542..9865aeedc58 100644 --- a/Documentation/hwmon/userspace-tools +++ b/Documentation/hwmon/userspace-tools @@ -6,31 +6,32 @@ voltages, fans speed). They are often connected through an I2C bus, but some are also connected directly through the ISA bus. The kernel drivers make the data from the sensor chips available in the /sys -virtual filesystem. Userspace tools are then used to display or set or the -data in a more friendly manner. +virtual filesystem. Userspace tools are then used to display the measured +values or configure the chips in a more friendly manner. Lm-sensors ---------- -Core set of utilites that will allow you to obtain health information, +Core set of utilities that will allow you to obtain health information, setup monitoring limits etc. You can get them on their homepage -http://www.lm-sensors.nu/ or as a package from your Linux distribution. +http://www.lm-sensors.org/ or as a package from your Linux distribution. If from website: -Get lmsensors from project web site. Please note, you need only userspace -part, so compile with "make user_install" target. +Get lm-sensors from project web site. Please note, you need only userspace +part, so compile with "make user" and install with "make user_install". General hints to get things working: 0) get lm-sensors userspace utils -1) compile all drivers in I2C section as modules in your kernel +1) compile all drivers in I2C and Hardware Monitoring sections as modules + in your kernel 2) run sensors-detect script, it will tell you what modules you need to load. 3) load them and run "sensors" command, you should see some results. 4) fix sensors.conf, labels, limits, fan divisors 5) if any more problems consult FAQ, or documentation -Other utilites --------------- +Other utilities +--------------- If you want some graphical indicators of system health look for applications like: gkrellm, ksensors, xsensors, wmtemp, wmsensors, wmgtemp, ksysguardd, diff --git a/Documentation/hwmon/vexpress b/Documentation/hwmon/vexpress new file mode 100644 index 00000000000..557d6d5ad90 --- /dev/null +++ b/Documentation/hwmon/vexpress @@ -0,0 +1,34 @@ +Kernel driver vexpress +====================== + +Supported systems: + * ARM Ltd. Versatile Express platform + Prefix: 'vexpress' + Datasheets: + * "Hardware Description" sections of the Technical Reference Manuals + for the Versatile Express boards: + http://infocenter.arm.com/help/topic/com.arm.doc.subset.boards.express/index.html + * Section "4.4.14. System Configuration registers" of the V2M-P1 TRM: + http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0447-/index.html + +Author: Pawel Moll + +Description +----------- + +Versatile Express platform (http://www.arm.com/versatileexpress/) is a +reference & prototyping system for ARM Ltd. processors. It can be set up +from a wide range of boards, each of them containing (apart of the main +chip/FPGA) a number of microcontrollers responsible for platform +configuration and control. Theses microcontrollers can also monitor the +board and its environment by a number of internal and external sensors, +providing information about power lines voltages and currents, board +temperature and power usage. Some of them also calculate consumed energy +and provide a cumulative use counter. + +The configuration devices are _not_ memory mapped and must be accessed +via a custom interface, abstracted by the "vexpress_config" API. + +As these devices are non-discoverable, they must be described in a Device +Tree passed to the kernel. Details of the DT binding for them can be found +in Documentation/devicetree/bindings/hwmon/vexpress.txt. diff --git a/Documentation/hwmon/via686a b/Documentation/hwmon/via686a index a936fb3824b..e5f90ab5c48 100644 --- a/Documentation/hwmon/via686a +++ b/Documentation/hwmon/via686a @@ -5,10 +5,10 @@ Supported chips: * Via VT82C686A, VT82C686B Southbridge Integrated Hardware Monitor Prefix: 'via686a' Addresses scanned: ISA in PCI-space encoded address - Datasheet: On request through web form (http://www.via.com.tw/en/support/datasheets/) + Datasheet: On request through web form (http://www.via.com.tw/en/resources/download-center/) Authors: - Kyösti Mälkki <kmalkki@cc.hut.fi>, + Kyösti Mälkki <kmalkki@cc.hut.fi>, Mark D. Studebaker <mdsxyz123@yahoo.com> Bob Dougherty <bobd@stanford.edu> (Some conversion-factor data were contributed by diff --git a/Documentation/hwmon/vt1211 b/Documentation/hwmon/vt1211 new file mode 100644 index 00000000000..77fa633b97a --- /dev/null +++ b/Documentation/hwmon/vt1211 @@ -0,0 +1,206 @@ +Kernel driver vt1211 +==================== + +Supported chips: + * VIA VT1211 + Prefix: 'vt1211' + Addresses scanned: none, address read from Super-I/O config space + Datasheet: Provided by VIA upon request and under NDA + +Authors: Juerg Haefliger <juergh@gmail.com> + +This driver is based on the driver for kernel 2.4 by Mark D. Studebaker and +its port to kernel 2.6 by Lars Ekman. + +Thanks to Joseph Chan and Fiona Gatt from VIA for providing documentation and +technical support. + + +Module Parameters +----------------- + +* uch_config: int Override the BIOS default universal channel (UCH) + configuration for channels 1-5. + Legal values are in the range of 0-31. Bit 0 maps to + UCH1, bit 1 maps to UCH2 and so on. Setting a bit to 1 + enables the thermal input of that particular UCH and + setting a bit to 0 enables the voltage input. + +* int_mode: int Override the BIOS default temperature interrupt mode. + The only possible value is 0 which forces interrupt + mode 0. In this mode, any pending interrupt is cleared + when the status register is read but is regenerated as + long as the temperature stays above the hysteresis + limit. + +Be aware that overriding BIOS defaults might cause some unwanted side effects! + + +Description +----------- + +The VIA VT1211 Super-I/O chip includes complete hardware monitoring +capabilities. It monitors 2 dedicated temperature sensor inputs (temp1 and +temp2), 1 dedicated voltage (in5) and 2 fans. Additionally, the chip +implements 5 universal input channels (UCH1-5) that can be individually +programmed to either monitor a voltage or a temperature. + +This chip also provides manual and automatic control of fan speeds (according +to the datasheet). The driver only supports automatic control since the manual +mode doesn't seem to work as advertised in the datasheet. In fact I couldn't +get manual mode to work at all! Be aware that automatic mode hasn't been +tested very well (due to the fact that my EPIA M10000 doesn't have the fans +connected to the PWM outputs of the VT1211 :-(). + +The following table shows the relationship between the vt1211 inputs and the +sysfs nodes. + +Sensor Voltage Mode Temp Mode Default Use (from the datasheet) +------ ------------ --------- -------------------------------- +Reading 1 temp1 Intel thermal diode +Reading 3 temp2 Internal thermal diode +UCH1/Reading2 in0 temp3 NTC type thermistor +UCH2 in1 temp4 +2.5V +UCH3 in2 temp5 VccP (processor core) +UCH4 in3 temp6 +5V +UCH5 in4 temp7 +12V ++3.3V in5 Internal VCC (+3.3V) + + +Voltage Monitoring +------------------ + +Voltages are sampled by an 8-bit ADC with a LSB of ~10mV. The supported input +range is thus from 0 to 2.60V. Voltage values outside of this range need +external scaling resistors. This external scaling needs to be compensated for +via compute lines in sensors.conf, like: + +compute inx @*(1+R1/R2), @/(1+R1/R2) + +The board level scaling resistors according to VIA's recommendation are as +follows. And this is of course totally dependent on the actual board +implementation :-) You will have to find documentation for your own +motherboard and edit sensors.conf accordingly. + + Expected +Voltage R1 R2 Divider Raw Value +----------------------------------------------- ++2.5V 2K 10K 1.2 2083 mV +VccP --- --- 1.0 1400 mV (1) ++5V 14K 10K 2.4 2083 mV ++12V 47K 10K 5.7 2105 mV ++3.3V (int) 2K 3.4K 1.588 3300 mV (2) ++3.3V (ext) 6.8K 10K 1.68 1964 mV + +(1) Depending on the CPU (1.4V is for a VIA C3 Nehemiah). +(2) R1 and R2 for 3.3V (int) are internal to the VT1211 chip and the driver + performs the scaling and returns the properly scaled voltage value. + +Each measured voltage has an associated low and high limit which triggers an +alarm when crossed. + + +Temperature Monitoring +---------------------- + +Temperatures are reported in millidegree Celsius. Each measured temperature +has a high limit which triggers an alarm if crossed. There is an associated +hysteresis value with each temperature below which the temperature has to drop +before the alarm is cleared (this is only true for interrupt mode 0). The +interrupt mode can be forced to 0 in case the BIOS doesn't do it +automatically. See the 'Module Parameters' section for details. + +All temperature channels except temp2 are external. Temp2 is the VT1211 +internal thermal diode and the driver does all the scaling for temp2 and +returns the temperature in millidegree Celsius. For the external channels +temp1 and temp3-temp7, scaling depends on the board implementation and needs +to be performed in userspace via sensors.conf. + +Temp1 is an Intel-type thermal diode which requires the following formula to +convert between sysfs readings and real temperatures: + +compute temp1 (@-Offset)/Gain, (@*Gain)+Offset + +According to the VIA VT1211 BIOS porting guide, the following gain and offset +values should be used: + +Diode Type Offset Gain +---------- ------ ---- +Intel CPU 88.638 0.9528 + 65.000 0.9686 *) +VIA C3 Ezra 83.869 0.9528 +VIA C3 Ezra-T 73.869 0.9528 + +*) This is the formula from the lm_sensors 2.10.0 sensors.conf file. I don't +know where it comes from or how it was derived, it's just listed here for +completeness. + +Temp3-temp7 support NTC thermistors. For these channels, the driver returns +the voltages as seen at the individual pins of UCH1-UCH5. The voltage at the +pin (Vpin) is formed by a voltage divider made of the thermistor (Rth) and a +scaling resistor (Rs): + +Vpin = 2200 * Rth / (Rs + Rth) (2200 is the ADC max limit of 2200 mV) + +The equation for the thermistor is as follows (google it if you want to know +more about it): + +Rth = Ro * exp(B * (1 / T - 1 / To)) (To is 298.15K (25C) and Ro is the + nominal resistance at 25C) + +Mingling the above two equations and assuming Rs = Ro and B = 3435 yields the +following formula for sensors.conf: + +compute tempx 1 / (1 / 298.15 - (` (2200 / @ - 1)) / 3435) - 273.15, + 2200 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) + + +Fan Speed Control +----------------- + +The VT1211 provides 2 programmable PWM outputs to control the speeds of 2 +fans. Writing a 2 to any of the two pwm[1-2]_enable sysfs nodes will put the +PWM controller in automatic mode. There is only a single controller that +controls both PWM outputs but each PWM output can be individually enabled and +disabled. + +Each PWM has 4 associated distinct output duty-cycles: full, high, low and +off. Full and off are internally hard-wired to 255 (100%) and 0 (0%), +respectively. High and low can be programmed via +pwm[1-2]_auto_point[2-3]_pwm. Each PWM output can be associated with a +different thermal input but - and here's the weird part - only one set of +thermal thresholds exist that controls both PWMs output duty-cycles. The +thermal thresholds are accessible via pwm[1-2]_auto_point[1-4]_temp. Note +that even though there are 2 sets of 4 auto points each, they map to the same +registers in the VT1211 and programming one set is sufficient (actually only +the first set pwm1_auto_point[1-4]_temp is writable, the second set is +read-only). + +PWM Auto Point PWM Output Duty-Cycle +------------------------------------------------ +pwm[1-2]_auto_point4_pwm full speed duty-cycle (hard-wired to 255) +pwm[1-2]_auto_point3_pwm high speed duty-cycle +pwm[1-2]_auto_point2_pwm low speed duty-cycle +pwm[1-2]_auto_point1_pwm off duty-cycle (hard-wired to 0) + +Temp Auto Point Thermal Threshold +--------------------------------------------- +pwm[1-2]_auto_point4_temp full speed temp +pwm[1-2]_auto_point3_temp high speed temp +pwm[1-2]_auto_point2_temp low speed temp +pwm[1-2]_auto_point1_temp off temp + +Long story short, the controller implements the following algorithm to set the +PWM output duty-cycle based on the input temperature: + +Thermal Threshold Output Duty-Cycle + (Rising Temp) (Falling Temp) +---------------------------------------------------------- + full speed duty-cycle full speed duty-cycle +full speed temp + high speed duty-cycle full speed duty-cycle +high speed temp + low speed duty-cycle high speed duty-cycle +low speed temp + off duty-cycle low speed duty-cycle +off temp diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf new file mode 100644 index 00000000000..735c42a85ea --- /dev/null +++ b/Documentation/hwmon/w83627ehf @@ -0,0 +1,190 @@ +Kernel driver w83627ehf +======================= + +Supported chips: + * Winbond W83627EHF/EHG (ISA access ONLY) + Prefix: 'w83627ehf' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: not available + * Winbond W83627DHG + Prefix: 'w83627dhg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: not available + * Winbond W83627DHG-P + Prefix: 'w83627dhg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: not available + * Winbond W83627UHG + Prefix: 'w83627uhg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: available from www.nuvoton.com + * Winbond W83667HG + Prefix: 'w83667hg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: not available + * Winbond W83667HG-B + Prefix: 'w83667hg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT6775F/W83667HG-I + Prefix: 'nct6775' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT6776F + Prefix: 'nct6776' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + +Authors: + Jean Delvare <jdelvare@suse.de> + Yuan Mu (Winbond) + Rudolf Marek <r.marek@assembler.cz> + David Hubbard <david.c.hubbard@gmail.com> + Gong Jun <JGong@nuvoton.com> + +Description +----------- + +This driver implements support for the Winbond W83627EHF, W83627EHG, +W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I +(NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively +as Winbond chips. + +The chips implement 3 to 4 temperature sensors (9 for NCT6775F and NCT6776F), +2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID +(except for 627UHG), alarms with beep warnings (control unimplemented), +and some automatic fan regulation strategies (plus manual fan control mode). + +The temperature sensor sources on W82677HG-B, NCT6775F, and NCT6776F are +configurable. temp4 and higher attributes are only reported if its temperature +source differs from the temperature sources of the already reported temperature +sensors. The configured source for each of the temperature sensors is provided +in tempX_label. + +Temperatures are measured in degrees Celsius and measurement resolution is 1 +degC for temp1 and and 0.5 degC for temp2 and temp3. For temp4 and higher, +resolution is 1 degC for W83667HG-B and 0.0 degC for NCT6775F and NCT6776F. +An alarm is triggered when the temperature gets higher than high limit; +it stays on until the temperature falls below the hysteresis value. +Alarms are only supported for temp1, temp2, and temp3. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or +128) to give the readings more range or accuracy. The driver sets the most +suitable fan divisor itself. Some fans might not be present because they +share pins with other functions. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +The driver supports automatic fan control mode known as Thermal Cruise. +In this mode, the chip attempts to keep the measured temperature in a +predefined temperature range. If the temperature goes out of range, fan +is driven slower/faster to reach the predefined range again. + +The mode works for fan1-fan4. Mapping of temperatures to pwm outputs is as +follows: + +temp1 -> pwm1 +temp2 -> pwm2 +temp3 -> pwm3 (not on 627UHG) +prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not + supported by the driver) + +/sys files +---------- + +name - this is a standard hwmon device entry, it contains the name of + the device (see the prefix in the list of supported devices at + the top of this file) + +pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: + 0 (stop) to 255 (full) + +pwm[1-4]_enable - this file controls mode of fan/temperature control: + * 1 Manual mode, write to pwm file any value 0-255 (full speed) + * 2 "Thermal Cruise" mode + * 3 "Fan Speed Cruise" mode + * 4 "Smart Fan III" mode + * 5 "Smart Fan IV" mode + + SmartFan III mode is not supported on NCT6776F. + + SmartFan IV mode is configurable only if it was configured at system + startup, and is only supported for W83677HG-B, NCT6775F, and NCT6776F. + SmartFan IV operational parameters can not be configured at this time, + and the various pwm attributes are not used in SmartFan IV mode. + The attributes can be written to, which is useful if you plan to + configure the system for a different pwm mode. However, the information + returned when reading pwm attributes is unrelated to SmartFan IV + operation. + +pwm[1-4]_mode - controls if output is PWM or DC level + * 0 DC output (0 - 12v) + * 1 PWM output + +Thermal Cruise mode +------------------- + +If the temperature is in the range defined by: + +pwm[1-4]_target - set target temperature, unit millidegree Celsius + (range 0 - 127000) +pwm[1-4]_tolerance - tolerance, unit millidegree Celsius (range 0 - 15000) + +there are no changes to fan speed. Once the temperature leaves the interval, +fan speed increases (temp is higher) or decreases if lower than desired. +There are defined steps and times, but not exported by the driver yet. + +pwm[1-4]_min_output - minimum fan speed (range 1 - 255), when the temperature + is below defined range. +pwm[1-4]_stop_time - how many milliseconds [ms] must elapse to switch + corresponding fan off. (when the temperature was below + defined range). +pwm[1-4]_start_output-minimum fan speed (range 1 - 255) when spinning up +pwm[1-4]_step_output- rate of fan speed change (1 - 255) +pwm[1-4]_stop_output- minimum fan speed (range 1 - 255) when spinning down +pwm[1-4]_max_output - maximum fan speed (range 1 - 255), when the temperature + is above defined range. + +Note: last six functions are influenced by other control bits, not yet exported + by the driver, so a change might not have any effect. + +Implementation Details +---------------------- + +Future driver development should bear in mind that the following registers have +different functions on the 627EHF and the 627DHG. Some registers also have +different power-on default values, but BIOS should already be loading +appropriate defaults. Note that bank selection must be performed as is currently +done in the driver for all register addresses. + +0x49: only on DHG, selects temperature source for AUX fan, CPU fan0 +0x4a: not completely documented for the EHF and the DHG documentation assigns + different behavior to bits 7 and 6, including extending the temperature + input selection to SmartFan I, not just SmartFan III. Testing on the EHF + will reveal whether they are compatible or not. + +0x58: Chip ID: 0xa1=EHF 0xc1=DHG +0x5e: only on DHG, has bits to enable "current mode" temperature detection and + critical temperature protection +0x45b: only on EHF, bit 3, vin4 alarm (EHF supports 10 inputs, only 9 on DHG) +0x552: only on EHF, vin4 +0x558: only on EHF, vin4 high limit +0x559: only on EHF, vin4 low limit +0x6b: only on DHG, SYS fan critical temperature +0x6c: only on DHG, CPU fan0 critical temperature +0x6d: only on DHG, AUX fan critical temperature +0x6e: only on DHG, CPU fan1 critical temperature + +0x50-0x55 and 0x650-0x657 are marked "Test Register" for the EHF, but "Reserved + Register" for the DHG + +The DHG also supports PECI, where the DHG queries Intel CPU temperatures, and +the ICH8 southbridge gets that data via PECI from the DHG, so that the +southbridge drives the fans. And the DHG supports SST, a one-wire serial bus. + +The DHG-P has an additional automatic fan speed control mode named Smart Fan +(TM) III+. This mode is not yet supported by the driver. diff --git a/Documentation/hwmon/w83627hf b/Documentation/hwmon/w83627hf index 5d23776e990..8432e111817 100644 --- a/Documentation/hwmon/w83627hf +++ b/Documentation/hwmon/w83627hf @@ -5,19 +5,19 @@ Supported chips: * Winbond W83627HF (ISA accesses ONLY) Prefix: 'w83627hf' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf * Winbond W83627THF Prefix: 'w83627thf' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: http://www.winbond.com/PDF/sheet/w83627thf.pdf * Winbond W83697HF Prefix: 'w83697hf' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: http://www.winbond.com/PDF/sheet/697hf.pdf * Winbond W83637HF Prefix: 'w83637hf' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: http://www.winbond.com/PDF/sheet/w83637hf.pdf + * Winbond W83687THF + Prefix: 'w83687thf' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Provided by Winbond on request(http://www.winbond.com/hq/enu) Authors: Frodo Looijaard <frodol@dds.nl>, @@ -28,8 +28,6 @@ Authors: Module Parameters ----------------- -* force_addr: int - Initialize the ISA address of the sensors * force_i2c: int Initialize the I2C address of the sensors * init: int @@ -65,5 +63,53 @@ doesn't help, you may just ignore the bogus VID reading with no harm done. For further information on this driver see the w83781d driver documentation. -[1] http://www2.lm-sensors.nu/~lm78/cvs/browse.cgi/lm_sensors2/doc/vid +[1] http://www.lm-sensors.org/browser/lm-sensors/trunk/doc/vid + +Forcing the address +------------------- + +The driver used to have a module parameter named force_addr, which could +be used to force the base I/O address of the hardware monitoring block. +This was meant as a workaround for mainboards with a broken BIOS. This +module parameter is gone for technical reasons. If you need this feature, +you can obtain the same result by using the isaset tool (part of +lm-sensors) before loading the driver: + +# Enter the Super I/O config space +isaset -y -f 0x2e 0x87 +isaset -y -f 0x2e 0x87 + +# Select the hwmon logical device +isaset -y 0x2e 0x2f 0x07 0x0b + +# Set the base I/O address (to 0x290 in this example) +isaset -y 0x2e 0x2f 0x60 0x02 +isaset -y 0x2e 0x2f 0x61 0x90 + +# Exit the Super-I/O config space +isaset -y -f 0x2e 0xaa + +The above sequence assumes a Super-I/O config space at 0x2e/0x2f, but +0x4e/0x4f is also possible. + +Voltage pin mapping +------------------- + +Here is a summary of the voltage pin mapping for the W83627THF. This +can be useful to convert data provided by board manufacturers into +working libsensors configuration statements. + + W83627THF | + Pin | Name | Register | Sysfs attribute +----------------------------------------------------- + 100 | CPUVCORE | 20h | in0 + 99 | VIN0 | 21h | in1 + 98 | VIN1 | 22h | in2 + 97 | VIN2 | 24h | in4 + 114 | AVCC | 23h | in3 + 61 | 5VSB | 50h (bank 5) | in7 + 74 | VBAT | 51h (bank 5) | in8 +For other supported devices, you'll have to take the hard path and +look up the information in the datasheet yourself (and then add it +to this document please.) diff --git a/Documentation/hwmon/w83781d b/Documentation/hwmon/w83781d index e5459333ba6..129b0a3b555 100644 --- a/Documentation/hwmon/w83781d +++ b/Documentation/hwmon/w83781d @@ -4,20 +4,16 @@ Kernel driver w83781d Supported chips: * Winbond W83781D Prefix: 'w83781d' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) + Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports) Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83781d.pdf * Winbond W83782D Prefix: 'w83782d' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) - Datasheet: http://www.winbond.com/PDF/sheet/w83782d.pdf + Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports) + Datasheet: http://www.winbond.com * Winbond W83783S Prefix: 'w83783s' Addresses scanned: I2C 0x2d Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83783s.pdf - * Winbond W83627HF - Prefix: 'w83627hf' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) - Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf * Asus AS99127F Prefix: 'as99127f' Addresses scanned: I2C 0x28 - 0x2f @@ -36,6 +32,11 @@ Module parameters Use 'init=0' to bypass initializing the chip. Try this if your computer crashes when you load the module. +* reset int + (default 0) + The driver used to reset the chip on load, but does no more. Use + 'reset=1' to restore the old behavior. Report if you need to do this. + force_subclients=bus,caddr,saddr,saddr This is used to force the i2c addresses for subclients of a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b' @@ -45,20 +46,18 @@ force_subclients=bus,caddr,saddr,saddr Description ----------- -This driver implements support for the Winbond W83781D, W83782D, W83783S, -W83627HF chips, and the Asus AS99127F chips. We will refer to them -collectively as W8378* chips. +This driver implements support for the Winbond W83781D, W83782D, W83783S +chips, and the Asus AS99127F chips. We will refer to them collectively as +W8378* chips. There is quite some difference between these chips, but they are similar enough that it was sensible to put them together in one driver. -The W83627HF chip is assumed to be identical to the ISA W83782D. The Asus chips are similar to an I2C-only W83782D. Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA as99127f 7 3 0 3 0x31 0x12c3 yes no as99127f rev.2 (type_name = as99127f) 0x31 0x5ca3 yes no w83781d 7 3 0 3 0x10-1 0x5ca3 yes yes -w83627hf 9 3 2 3 0x21 0x5ca3 yes yes(LPC) w83782d 9 3 2-4 3 0x30 0x5ca3 yes yes w83783s 5-6 3 2 1-2 0x40 0x5ca3 yes no @@ -123,6 +122,25 @@ When an alarm goes off, you can be warned by a beeping signal through your computer speaker. It is possible to enable all beeping globally, or only the beeping for some alarms. +Individual alarm and beep bits: + +0x000001: in0 +0x000002: in1 +0x000004: in2 +0x000008: in3 +0x000010: temp1 +0x000020: temp2 (+temp3 on W83781D) +0x000040: fan1 +0x000080: fan2 +0x000100: in4 +0x000200: in5 +0x000400: in6 +0x000800: fan3 +0x001000: chassis +0x002000: temp3 (W83782D only) +0x010000: in7 (W83782D only) +0x020000: in8 (W83782D only) + If an alarm triggers, it will remain triggered until the hardware register is read at least once. This means that the cause for the alarm may already have disappeared! Note that in the current implementation, all @@ -335,7 +353,7 @@ in6=255 # PWM -Additional info about PWM on the AS99127F (may apply to other Asus +* Additional info about PWM on the AS99127F (may apply to other Asus chips as well) by Jean Delvare as of 2004-04-09: AS99127F revision 2 seems to have two PWM registers at 0x59 and 0x5A, @@ -378,14 +396,14 @@ Please contact us if you can figure out how it is supposed to work. As long as we don't know more, the w83781d driver doesn't handle PWM on AS99127F chips at all. -Additional info about PWM on the AS99127F rev.1 by Hector Martin: +* Additional info about PWM on the AS99127F rev.1 by Hector Martin: I've been fiddling around with the (in)famous 0x59 register and found out the following values do work as a form of coarse pwm: 0x80 - seems to turn fans off after some time(1-2 minutes)... might be some form of auto-fan-control based on temp? hmm (Qfan? this mobo is an -old ASUS, it isn't marketed as Qfan. Maybe some beta pre-attemp at Qfan +old ASUS, it isn't marketed as Qfan. Maybe some beta pre-attempt at Qfan that was dropped at the BIOS) 0x81 - off 0x82 - slightly "on-ner" than off, but my fans do not get to move. I can @@ -400,3 +418,36 @@ change. My mobo is an ASUS A7V266-E. This behavior is similar to what I got with speedfan under Windows, where 0-15% would be off, 15-2x% (can't remember the exact value) would be 70% and higher would be full on. + +* Additional info about PWM on the AS99127F rev.1 from lm-sensors + ticket #2350: + +I conducted some experiment on Asus P3B-F motherboard with AS99127F +(Ver. 1). + +I confirm that 0x59 register control the CPU_Fan Header on this +motherboard, and 0x5a register control PWR_Fan. + +In order to reduce the dependency of specific fan, the measurement is +conducted with a digital scope without fan connected. I found out that +P3B-F actually output variable DC voltage on fan header center pin, +looks like PWM is filtered on this motherboard. + +Here are some of measurements: + +0x80 20 mV +0x81 20 mV +0x82 232 mV +0x83 1.2 V +0x84 2.31 V +0x85 3.44 V +0x86 4.62 V +0x87 5.81 V +0x88 7.01 V +9x89 8.22 V +0x8a 9.42 V +0x8b 10.6 V +0x8c 11.9 V +0x8d 12.4 V +0x8e 12.4 V +0x8f 12.4 V diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d new file mode 100644 index 00000000000..f4021a28546 --- /dev/null +++ b/Documentation/hwmon/w83791d @@ -0,0 +1,161 @@ +Kernel driver w83791d +===================== + +Supported chips: + * Winbond W83791D + Prefix: 'w83791d' + Addresses scanned: I2C 0x2c - 0x2f + Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791D_W83791Gb.pdf + +Author: Charles Spirakis <bezaur@gmail.com> + +This driver was derived from the w83781d.c and w83792d.c source files. + +Credits: + w83781d.c: + Frodo Looijaard <frodol@dds.nl>, + Philip Edelbrock <phil@netroedge.com>, + and Mark Studebaker <mdsxyz123@yahoo.com> + w83792d.c: + Shane Huang (Winbond), + Rudolf Marek <r.marek@assembler.cz> + +Additional contributors: + Sven Anders <anders@anduras.de> + Marc Hulsman <m.hulsman@tudelft.nl> + +Module Parameters +----------------- + +* init boolean + (default 0) + Use 'init=1' to have the driver do extra software initializations. + The default behavior is to do the minimum initialization possible + and depend on the BIOS to properly setup the chip. If you know you + have a w83791d and you're having problems, try init=1 before trying + reset=1. + +* reset boolean + (default 0) + Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default + behavior is no chip reset to preserve BIOS settings. + +* force_subclients=bus,caddr,saddr,saddr + This is used to force the i2c addresses for subclients of + a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b' + to force the subclients of chip 0x2f on bus 0 to i2c addresses + 0x4a and 0x4b. + + +Description +----------- + +This driver implements support for the Winbond W83791D chip. The W83791G +chip appears to be the same as the W83791D but is lead free. + +Detection of the chip can sometimes be foiled because it can be in an +internal state that allows no clean access (Bank with ID register is not +currently selected). If you know the address of the chip, use a 'force' +parameter; this will put it into a more well-behaved state first. + +The driver implements three temperature sensors, ten voltage sensors, +five fan rotation speed sensors and manual PWM control of each fan. + +Temperatures are measured in degrees Celsius and measurement resolution is 1 +degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when +the temperature gets higher than the Overtemperature Shutdown value; it stays +on until the temperature falls below the Hysteresis value. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4, 8, 16, +32, 64 or 128 for all fans) to give the readings more range or accuracy. + +Each fan controlled is controlled by PWM. The PWM duty cycle can be read and +set for each fan separately. Valid values range from 0 (stop) to 255 (full). +PWM 1-3 support Thermal Cruise mode, in which the PWMs are automatically +regulated to keep respectively temp 1-3 at a certain target temperature. +See below for the description of the sysfs-interface. + +The w83791d has a global bit used to enable beeping from the speaker when an +alarm is triggered as well as a bitmask to enable or disable the beep for +specific alarms. You need both the global beep enable bit and the +corresponding beep bit to be on for a triggered alarm to sound a beep. + +The sysfs interface to the global enable is via the sysfs beep_enable file. +This file is used for both legacy and new code. + +The sysfs interface to the beep bitmask has migrated from the original legacy +method of a single sysfs beep_mask file to a newer method using multiple +*_beep files as described in .../Documentation/hwmon/sysfs-interface. + +A similar change has occurred for the bitmap corresponding to the alarms. The +original legacy method used a single sysfs alarms file containing a bitmap +of triggered alarms. The newer method uses multiple sysfs *_alarm files +(again following the pattern described in sysfs-interface). + +Since both methods read and write the underlying hardware, they can be used +interchangeably and changes in one will automatically be reflected by +the other. If you use the legacy bitmask method, your user-space code is +responsible for handling the fact that the alarms and beep_mask bitmaps +are not the same (see the table below). + +NOTE: All new code should be written to use the newer sysfs-interface +specification as that avoids bitmap problems and is the preferred interface +going forward. + +The driver reads the hardware chip values at most once every three seconds. +User mode code requesting values more often will receive cached values. + +/sys files +---------- +The sysfs-interface is documented in the 'sysfs-interface' file. Only +chip-specific options are documented here. + +pwm[1-3]_enable - this file controls mode of fan/temperature control for + fan 1-3. Fan/PWM 4-5 only support manual mode. + * 1 Manual mode + * 2 Thermal Cruise mode + * 3 Fan Speed Cruise mode (no further support) + +temp[1-3]_target - defines the target temperature for Thermal Cruise mode. + Unit: millidegree Celsius + RW + +temp[1-3]_tolerance - temperature tolerance for Thermal Cruise mode. + Specifies an interval around the target temperature + in which the fan speed is not changed. + Unit: millidegree Celsius + RW + +Alarms bitmap vs. beep_mask bitmask +------------------------------------ +For legacy code using the alarms and beep_mask files: + +in0 (VCORE) : alarms: 0x000001 beep_mask: 0x000001 +in1 (VINR0) : alarms: 0x000002 beep_mask: 0x002000 <== mismatch +in2 (+3.3VIN): alarms: 0x000004 beep_mask: 0x000004 +in3 (5VDD) : alarms: 0x000008 beep_mask: 0x000008 +in4 (+12VIN) : alarms: 0x000100 beep_mask: 0x000100 +in5 (-12VIN) : alarms: 0x000200 beep_mask: 0x000200 +in6 (-5VIN) : alarms: 0x000400 beep_mask: 0x000400 +in7 (VSB) : alarms: 0x080000 beep_mask: 0x010000 <== mismatch +in8 (VBAT) : alarms: 0x100000 beep_mask: 0x020000 <== mismatch +in9 (VINR1) : alarms: 0x004000 beep_mask: 0x004000 +temp1 : alarms: 0x000010 beep_mask: 0x000010 +temp2 : alarms: 0x000020 beep_mask: 0x000020 +temp3 : alarms: 0x002000 beep_mask: 0x000002 <== mismatch +fan1 : alarms: 0x000040 beep_mask: 0x000040 +fan2 : alarms: 0x000080 beep_mask: 0x000080 +fan3 : alarms: 0x000800 beep_mask: 0x000800 +fan4 : alarms: 0x200000 beep_mask: 0x200000 +fan5 : alarms: 0x400000 beep_mask: 0x400000 +tart1 : alarms: 0x010000 beep_mask: 0x040000 <== mismatch +tart2 : alarms: 0x020000 beep_mask: 0x080000 <== mismatch +tart3 : alarms: 0x040000 beep_mask: 0x100000 <== mismatch +case_open : alarms: 0x001000 beep_mask: 0x001000 +global_enable: alarms: -------- beep_mask: 0x800000 (modified via beep_enable) diff --git a/Documentation/hwmon/w83792d b/Documentation/hwmon/w83792d index 8171c285bb5..53f7b6866fe 100644 --- a/Documentation/hwmon/w83792d +++ b/Documentation/hwmon/w83792d @@ -5,10 +5,9 @@ Supported chips: * Winbond W83792D Prefix: 'w83792d' Addresses scanned: I2C 0x2c - 0x2f - Datasheet: http://www.winbond.com.tw/E-WINBONDHTM/partner/PDFresult.asp?Pname=1035 + Datasheet: http://www.winbond.com.tw -Author: Chunhao Huang -Contact: DZShen <DZShen@Winbond.com.tw> +Author: Shane Huang (Winbond) Module Parameters @@ -107,7 +106,7 @@ Known problems: by CR[0x49h]. - The function of vid and vrm has not been finished, because I'm NOT very familiar with them. Adding support is welcome. - - The function of chassis open detection needs more tests. + - The function of chassis open detection needs more tests. - If you have ASUS server board and chip was not found: Then you will need to upgrade to latest (or beta) BIOS. If it does not help please contact us. diff --git a/Documentation/hwmon/w83793 b/Documentation/hwmon/w83793 new file mode 100644 index 00000000000..6cc5f639b72 --- /dev/null +++ b/Documentation/hwmon/w83793 @@ -0,0 +1,106 @@ +Kernel driver w83793 +==================== + +Supported chips: + * Winbond W83793G/W83793R + Prefix: 'w83793' + Addresses scanned: I2C 0x2c - 0x2f + Datasheet: Still not published + +Authors: + Yuan Mu (Winbond Electronics) + Rudolf Marek <r.marek@assembler.cz> + + +Module parameters +----------------- + +* reset int + (default 0) + This parameter is not recommended, it will lose motherboard specific + settings. Use 'reset=1' to reset the chip when loading this module. + +* force_subclients=bus,caddr,saddr1,saddr2 + This is used to force the i2c addresses for subclients of + a certain chip. Typical usage is `force_subclients=0,0x2f,0x4a,0x4b' + to force the subclients of chip 0x2f on bus 0 to i2c addresses + 0x4a and 0x4b. + + +Description +----------- + +This driver implements support for Winbond W83793G/W83793R chips. + +* Exported features + This driver exports 10 voltage sensors, up to 12 fan tachometer inputs, + 6 remote temperatures, up to 8 sets of PWM fan controls, SmartFan + (automatic fan speed control) on all temperature/PWM combinations, 2 + sets of 6-pin CPU VID input. + +* Sensor resolutions + If your motherboard maker used the reference design, the resolution of + voltage0-2 is 2mV, resolution of voltage3/4/5 is 16mV, 8mV for voltage6, + 24mV for voltage7/8. Temp1-4 have a 0.25 degree Celsius resolution, + temp5-6 have a 1 degree Celsiis resolution. + +* Temperature sensor types + Temp1-4 have 2 possible types. It can be read from (and written to) + temp[1-4]_type. + - If the value is 3, it starts monitoring using a remote termal diode + (default). + - If the value is 6, it starts monitoring using the temperature sensor + in Intel CPU and get result by PECI. + Temp5-6 can be connected to external thermistors (value of + temp[5-6]_type is 4). + +* Alarm mechanism + For voltage sensors, an alarm triggers if the measured value is below + the low voltage limit or over the high voltage limit. + For temperature sensors, an alarm triggers if the measured value goes + above the high temperature limit, and wears off only after the measured + value drops below the hysteresis value. + For fan sensors, an alarm triggers if the measured value is below the + low speed limit. + +* SmartFan/PWM control + If you want to set a pwm fan to manual mode, you just need to make sure it + is not controlled by any temp channel, for example, you want to set fan1 + to manual mode, you need to check the value of temp[1-6]_fan_map, make + sure bit 0 is cleared in the 6 values. And then set the pwm1 value to + control the fan. + + Each temperature channel can control all the 8 PWM outputs (by setting the + corresponding bit in tempX_fan_map), you can set the temperature channel + mode using temp[1-6]_pwm_enable, 2 is Thermal Cruise mode and 3 + is the SmartFanII mode. Temperature channels will try to speed up or + slow down all controlled fans, this means one fan can receive different + PWM value requests from different temperature channels, but the chip + will always pick the safest (max) PWM value for each fan. + + In Thermal Cruise mode, the chip attempts to keep the temperature at a + predefined value, within a tolerance margin. So if tempX_input > + thermal_cruiseX + toleranceX, the chip will increase the PWM value, + if tempX_input < thermal_cruiseX - toleranceX, the chip will decrease + the PWM value. If the temperature is within the tolerance range, the PWM + value is left unchanged. + + SmartFanII works differently, you have to define up to 7 PWM, temperature + trip points, defining a PWM/temperature curve which the chip will follow. + While not fundamentally different from the Thermal Cruise mode, the + implementation is quite different, giving you a finer-grained control. + +* Chassis + If the case open alarm triggers, it will stay in this state unless cleared + by writing 0 to the sysfs file "intrusion0_alarm". + +* VID and VRM + The VRM version is detected automatically, don't modify the it unless you + *do* know the cpu VRM version and it's not properly detected. + + +Notes +----- + + Only Fan1-5 and PWM1-3 are guaranteed to always exist, other fan inputs and + PWM outputs may or may not exist depending on the chip pin configuration. diff --git a/Documentation/hwmon/w83795 b/Documentation/hwmon/w83795 new file mode 100644 index 00000000000..d3e678216b9 --- /dev/null +++ b/Documentation/hwmon/w83795 @@ -0,0 +1,127 @@ +Kernel driver w83795 +==================== + +Supported chips: + * Winbond/Nuvoton W83795G + Prefix: 'w83795g' + Addresses scanned: I2C 0x2c - 0x2f + Datasheet: Available for download on nuvoton.com + * Winbond/Nuvoton W83795ADG + Prefix: 'w83795adg' + Addresses scanned: I2C 0x2c - 0x2f + Datasheet: Available for download on nuvoton.com + +Authors: + Wei Song (Nuvoton) + Jean Delvare <jdelvare@suse.de> + + +Pin mapping +----------- + +Here is a summary of the pin mapping for the W83795G and W83795ADG. +This can be useful to convert data provided by board manufacturers +into working libsensors configuration statements. + + W83795G | + Pin | Name | Register | Sysfs attribute +------------------------------------------------------------------ + 13 | VSEN1 (VCORE1) | 10h | in0 + 14 | VSEN2 (VCORE2) | 11h | in1 + 15 | VSEN3 (VCORE3) | 12h | in2 + 16 | VSEN4 | 13h | in3 + 17 | VSEN5 | 14h | in4 + 18 | VSEN6 | 15h | in5 + 19 | VSEN7 | 16h | in6 + 20 | VSEN8 | 17h | in7 + 21 | VSEN9 | 18h | in8 + 22 | VSEN10 | 19h | in9 + 23 | VSEN11 | 1Ah | in10 + 28 | VTT | 1Bh | in11 + 24 | 3VDD | 1Ch | in12 + 25 | 3VSB | 1Dh | in13 + 26 | VBAT | 1Eh | in14 + 3 | VSEN12/TR5 | 1Fh | in15/temp5 + 4 | VSEN13/TR5 | 20h | in16/temp6 + 5/ 6 | VDSEN14/TR1/TD1 | 21h | in17/temp1 + 7/ 8 | VDSEN15/TR2/TD2 | 22h | in18/temp2 + 9/ 10 | VDSEN16/TR3/TD3 | 23h | in19/temp3 + 11/ 12 | VDSEN17/TR4/TD4 | 24h | in20/temp4 + 40 | FANIN1 | 2Eh | fan1 + 42 | FANIN2 | 2Fh | fan2 + 44 | FANIN3 | 30h | fan3 + 46 | FANIN4 | 31h | fan4 + 48 | FANIN5 | 32h | fan5 + 50 | FANIN6 | 33h | fan6 + 52 | FANIN7 | 34h | fan7 + 54 | FANIN8 | 35h | fan8 + 57 | FANIN9 | 36h | fan9 + 58 | FANIN10 | 37h | fan10 + 59 | FANIN11 | 38h | fan11 + 60 | FANIN12 | 39h | fan12 + 31 | FANIN13 | 3Ah | fan13 + 35 | FANIN14 | 3Bh | fan14 + 41 | FANCTL1 | 10h (bank 2) | pwm1 + 43 | FANCTL2 | 11h (bank 2) | pwm2 + 45 | FANCTL3 | 12h (bank 2) | pwm3 + 47 | FANCTL4 | 13h (bank 2) | pwm4 + 49 | FANCTL5 | 14h (bank 2) | pwm5 + 51 | FANCTL6 | 15h (bank 2) | pwm6 + 53 | FANCTL7 | 16h (bank 2) | pwm7 + 55 | FANCTL8 | 17h (bank 2) | pwm8 + 29/ 30 | PECI/TSI (DTS1) | 26h | temp7 + 29/ 30 | PECI/TSI (DTS2) | 27h | temp8 + 29/ 30 | PECI/TSI (DTS3) | 28h | temp9 + 29/ 30 | PECI/TSI (DTS4) | 29h | temp10 + 29/ 30 | PECI/TSI (DTS5) | 2Ah | temp11 + 29/ 30 | PECI/TSI (DTS6) | 2Bh | temp12 + 29/ 30 | PECI/TSI (DTS7) | 2Ch | temp13 + 29/ 30 | PECI/TSI (DTS8) | 2Dh | temp14 + 27 | CASEOPEN# | 46h | intrusion0 + + W83795ADG | + Pin | Name | Register | Sysfs attribute +------------------------------------------------------------------ + 10 | VSEN1 (VCORE1) | 10h | in0 + 11 | VSEN2 (VCORE2) | 11h | in1 + 12 | VSEN3 (VCORE3) | 12h | in2 + 13 | VSEN4 | 13h | in3 + 14 | VSEN5 | 14h | in4 + 15 | VSEN6 | 15h | in5 + 16 | VSEN7 | 16h | in6 + 17 | VSEN8 | 17h | in7 + 22 | VTT | 1Bh | in11 + 18 | 3VDD | 1Ch | in12 + 19 | 3VSB | 1Dh | in13 + 20 | VBAT | 1Eh | in14 + 48 | VSEN12/TR5 | 1Fh | in15/temp5 + 1 | VSEN13/TR5 | 20h | in16/temp6 + 2/ 3 | VDSEN14/TR1/TD1 | 21h | in17/temp1 + 4/ 5 | VDSEN15/TR2/TD2 | 22h | in18/temp2 + 6/ 7 | VDSEN16/TR3/TD3 | 23h | in19/temp3 + 8/ 9 | VDSEN17/TR4/TD4 | 24h | in20/temp4 + 32 | FANIN1 | 2Eh | fan1 + 34 | FANIN2 | 2Fh | fan2 + 36 | FANIN3 | 30h | fan3 + 37 | FANIN4 | 31h | fan4 + 38 | FANIN5 | 32h | fan5 + 39 | FANIN6 | 33h | fan6 + 40 | FANIN7 | 34h | fan7 + 41 | FANIN8 | 35h | fan8 + 43 | FANIN9 | 36h | fan9 + 44 | FANIN10 | 37h | fan10 + 45 | FANIN11 | 38h | fan11 + 46 | FANIN12 | 39h | fan12 + 24 | FANIN13 | 3Ah | fan13 + 28 | FANIN14 | 3Bh | fan14 + 33 | FANCTL1 | 10h (bank 2) | pwm1 + 35 | FANCTL2 | 11h (bank 2) | pwm2 + 23 | PECI (DTS1) | 26h | temp7 + 23 | PECI (DTS2) | 27h | temp8 + 23 | PECI (DTS3) | 28h | temp9 + 23 | PECI (DTS4) | 29h | temp10 + 23 | PECI (DTS5) | 2Ah | temp11 + 23 | PECI (DTS6) | 2Bh | temp12 + 23 | PECI (DTS7) | 2Ch | temp13 + 23 | PECI (DTS8) | 2Dh | temp14 + 21 | CASEOPEN# | 46h | intrusion0 diff --git a/Documentation/hwmon/w83l785ts b/Documentation/hwmon/w83l785ts index 1841cedc25b..c8978478871 100644 --- a/Documentation/hwmon/w83l785ts +++ b/Documentation/hwmon/w83l785ts @@ -9,7 +9,7 @@ Supported chips: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83L785TS-S.pdf Authors: - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Description ----------- @@ -33,7 +33,8 @@ Known Issues ------------ On some systems (Asus), the BIOS is known to interfere with the driver -and cause read errors. The driver will retry a given number of times +and cause read errors. Or maybe the W83L785TS-S chip is simply unreliable, +we don't really know. The driver will retry a given number of times (5 by default) and then give up, returning the old value (or 0 if there is no old value). It seems to work well enough so that you should not notice anything. Thanks to James Bolt for helping test this feature. diff --git a/Documentation/hwmon/w83l786ng b/Documentation/hwmon/w83l786ng new file mode 100644 index 00000000000..d8f55d7fff1 --- /dev/null +++ b/Documentation/hwmon/w83l786ng @@ -0,0 +1,54 @@ +Kernel driver w83l786ng +===================== + +Supported chips: + * Winbond W83L786NG/W83L786NR + Prefix: 'w83l786ng' + Addresses scanned: I2C 0x2e - 0x2f + Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83L786NRNG09.pdf + +Author: Kevin Lo <kevlo@kevlo.org> + + +Module Parameters +----------------- + +* reset boolean + (default 0) + Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default + behavior is no chip reset to preserve BIOS settings + + +Description +----------- + +This driver implements support for Winbond W83L786NG/W83L786NR chips. + +The driver implements two temperature sensors, two fan rotation speed +sensors, and three voltage sensors. + +Temperatures are measured in degrees Celsius and measurement resolution is 1 +degC for temp1 and temp2. + +Fan rotation speeds are reported in RPM (rotations per minute). Fan readings +readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 +or 128 for fan 1/2) to give the readings more range or accuracy. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +/sys files +---------- + +pwm[1-2] - this file stores PWM duty cycle or DC value (fan speed) in range: + 0 (stop) to 255 (full) +pwm[1-2]_enable - this file controls mode of fan/temperature control: + * 0 Manual Mode + * 1 Thermal Cruise + * 2 Smart Fan II + * 4 FAN_SET +pwm[1-2]_mode - Select PWM of DC mode + * 0 DC + * 1 PWM +tolerance[1-2] - Value in degrees of Celsius (degC) for +- T diff --git a/Documentation/hwmon/wm831x b/Documentation/hwmon/wm831x new file mode 100644 index 00000000000..11446757c8c --- /dev/null +++ b/Documentation/hwmon/wm831x @@ -0,0 +1,37 @@ +Kernel driver wm831x-hwmon +========================== + +Supported chips: + * Wolfson Microelectronics WM831x PMICs + Prefix: 'wm831x' + Datasheet: + http://www.wolfsonmicro.com/products/WM8310 + http://www.wolfsonmicro.com/products/WM8311 + http://www.wolfsonmicro.com/products/WM8312 + +Authors: Mark Brown <broonie@opensource.wolfsonmicro.com> + +Description +----------- + +The WM831x series of PMICs include an AUXADC which can be used to +monitor a range of system operating parameters, including the voltages +of the major supplies within the system. Currently the driver provides +reporting of all the input values but does not provide any alarms. + +Voltage Monitoring +------------------ + +Voltages are sampled by a 12 bit ADC. Voltages in millivolts are 1.465 +times the ADC value. + +Temperature Monitoring +---------------------- + +Temperatures are sampled by a 12 bit ADC. Chip and battery temperatures +are available. The chip temperature is calculated as: + + Degrees celsius = (512.18 - data) / 1.0983 + +while the battery temperature calculation will depend on the NTC +thermistor component. diff --git a/Documentation/hwmon/wm8350 b/Documentation/hwmon/wm8350 new file mode 100644 index 00000000000..98f923bd2e9 --- /dev/null +++ b/Documentation/hwmon/wm8350 @@ -0,0 +1,26 @@ +Kernel driver wm8350-hwmon +========================== + +Supported chips: + * Wolfson Microelectronics WM835x PMICs + Prefix: 'wm8350' + Datasheet: + http://www.wolfsonmicro.com/products/WM8350 + http://www.wolfsonmicro.com/products/WM8351 + http://www.wolfsonmicro.com/products/WM8352 + +Authors: Mark Brown <broonie@opensource.wolfsonmicro.com> + +Description +----------- + +The WM835x series of PMICs include an AUXADC which can be used to +monitor a range of system operating parameters, including the voltages +of the major supplies within the system. Currently the driver provides +simple access to these major supplies. + +Voltage Monitoring +------------------ + +Voltages are sampled by a 12 bit ADC. For the internal supplies the ADC +is referenced to the system VRTC. diff --git a/Documentation/hwmon/zl6100 b/Documentation/hwmon/zl6100 new file mode 100644 index 00000000000..33908a4d68f --- /dev/null +++ b/Documentation/hwmon/zl6100 @@ -0,0 +1,160 @@ +Kernel driver zl6100 +==================== + +Supported chips: + * Intersil / Zilker Labs ZL2004 + Prefix: 'zl2004' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6847.pdf + * Intersil / Zilker Labs ZL2005 + Prefix: 'zl2005' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6848.pdf + * Intersil / Zilker Labs ZL2006 + Prefix: 'zl2006' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6850.pdf + * Intersil / Zilker Labs ZL2008 + Prefix: 'zl2008' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6859.pdf + * Intersil / Zilker Labs ZL2105 + Prefix: 'zl2105' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6851.pdf + * Intersil / Zilker Labs ZL2106 + Prefix: 'zl2106' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6852.pdf + * Intersil / Zilker Labs ZL6100 + Prefix: 'zl6100' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6876.pdf + * Intersil / Zilker Labs ZL6105 + Prefix: 'zl6105' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn6906.pdf + * Intersil / Zilker Labs ZL9101M + Prefix: 'zl9101' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn7669.pdf + * Intersil / Zilker Labs ZL9117M + Prefix: 'zl9117' + Addresses scanned: - + Datasheet: http://www.intersil.com/data/fn/fn7914.pdf + * Ericsson BMR450, BMR451 + Prefix: 'bmr450', 'bmr451' + Addresses scanned: - + Datasheet: +http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146401 + * Ericsson BMR462, BMR463, BMR464 + Prefixes: 'bmr462', 'bmr463', 'bmr464' + Addresses scanned: - + Datasheet: +http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146256 + + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver supports hardware montoring for Intersil / Zilker Labs ZL6100 and +compatible digital DC-DC controllers. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus and Documentation.hwmon/pmbus-core for details +on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + +WARNING: Do not access chip registers using the i2cdump command, and do not use +any of the i2ctools commands on a command register used to save and restore +configuration data (0x11, 0x12, 0x15, 0x16, and 0xf4). The chips supported by +this driver interpret any access to those command registers (including read +commands) as request to execute the command in question. Unless write accesses +to those registers are protected, this may result in power loss, board resets, +and/or Flash corruption. Worst case, your board may turn into a brick. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Module parameters +----------------- + +delay +----- + +Intersil/Zilker Labs DC-DC controllers require a minimum interval between I2C +bus accesses. According to Intersil, the minimum interval is 2 ms, though 1 ms +appears to be sufficient and has not caused any problems in testing. The problem +is known to affect all currently supported chips. For manual override, the +driver provides a writeable module parameter, 'delay', which can be used to set +the interval to a value between 0 and 65,535 microseconds. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vin" +in1_input Measured input voltage. +in1_min Minimum input voltage. +in1_max Maximum input voltage. +in1_lcrit Critical minimum input voltage. +in1_crit Critical maximum input voltage. +in1_min_alarm Input voltage low alarm. +in1_max_alarm Input voltage high alarm. +in1_lcrit_alarm Input voltage critical low alarm. +in1_crit_alarm Input voltage critical high alarm. + +in2_label "vmon" +in2_input Measured voltage on VMON (ZL2004) or VDRV (ZL9101M, + ZL9117M) pin. Reported voltage is 16x the voltage on the + pin (adjusted internally by the chip). +in2_lcrit Critical minimum VMON/VDRV Voltage. +in2_crit Critical maximum VMON/VDRV voltage. +in2_lcrit_alarm VMON/VDRV voltage critical low alarm. +in2_crit_alarm VMON/VDRV voltage critical high alarm. + + vmon attributes are supported on ZL2004, ZL9101M, + and ZL9117M only. + +inX_label "vout1" +inX_input Measured output voltage. +inX_lcrit Critical minimum output Voltage. +inX_crit Critical maximum output voltage. +inX_lcrit_alarm Critical output voltage critical low alarm. +inX_crit_alarm Critical output voltage critical high alarm. + + X is 3 for ZL2004, ZL9101M, and ZL9117M, 2 otherwise. + +curr1_label "iout1" +curr1_input Measured output current. +curr1_lcrit Critical minimum output current. +curr1_crit Critical maximum output current. +curr1_lcrit_alarm Output current critical low alarm. +curr1_crit_alarm Output current critical high alarm. + +temp[12]_input Measured temperature. +temp[12]_min Minimum temperature. +temp[12]_max Maximum temperature. +temp[12]_lcrit Critical low temperature. +temp[12]_crit Critical high temperature. +temp[12]_min_alarm Chip temperature low alarm. +temp[12]_max_alarm Chip temperature high alarm. +temp[12]_lcrit_alarm Chip temperature critical low alarm. +temp[12]_crit_alarm Chip temperature critical high alarm. |