diff options
Diffstat (limited to 'Documentation/hwmon/w83627ehf')
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 37 |
1 files changed, 22 insertions, 15 deletions
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index 76ffef94ed7..735c42a85ea 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -14,6 +14,10 @@ Supported chips: Prefix: 'w83627dhg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: not available + * Winbond W83627UHG + Prefix: 'w83627uhg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: available from www.nuvoton.com * Winbond W83667HG Prefix: 'w83667hg' Addresses scanned: ISA address retrieved from Super I/O registers @@ -32,7 +36,7 @@ Supported chips: Datasheet: Available from Nuvoton upon request Authors: - Jean Delvare <khali@linux-fr.org> + Jean Delvare <jdelvare@suse.de> Yuan Mu (Winbond) Rudolf Marek <r.marek@assembler.cz> David Hubbard <david.c.hubbard@gmail.com> @@ -42,14 +46,13 @@ Description ----------- This driver implements support for the Winbond W83627EHF, W83627EHG, -W83627DHG, W83627DHG-P, W83667HG, W83667HG-B, W83667HG-I (NCT6775F), -and NCT6776F super I/O chips. We will refer to them collectively as -Winbond chips. - -The chips implement three temperature sensors (up to four for 667HG-B, and nine -for NCT6775F and NCT6776F), five fan rotation speed sensors, ten analog voltage -sensors (only nine for the 627DHG), one VID (6 pins for the 627EHF/EHG, 8 pins -for the 627DHG and 667HG), alarms with beep warnings (control unimplemented), +W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I +(NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively +as Winbond chips. + +The chips implement 3 to 4 temperature sensors (9 for NCT6775F and NCT6776F), +2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID +(except for 627UHG), alarms with beep warnings (control unimplemented), and some automatic fan regulation strategies (plus manual fan control mode). The temperature sensor sources on W82677HG-B, NCT6775F, and NCT6776F are @@ -86,17 +89,16 @@ follows: temp1 -> pwm1 temp2 -> pwm2 -temp3 -> pwm3 +temp3 -> pwm3 (not on 627UHG) prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not supported by the driver) /sys files ---------- -name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG, - it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg", - for the W83667HG and W83667HG-B it is set to "w83667hg", for NCT6775F it - is set to "nct6775", and for NCT6776F it is set to "nct6776". +name - this is a standard hwmon device entry, it contains the name of + the device (see the prefix in the list of supported devices at + the top of this file) pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: 0 (stop) to 255 (full) @@ -141,8 +143,13 @@ pwm[1-4]_min_output - minimum fan speed (range 1 - 255), when the temperature pwm[1-4]_stop_time - how many milliseconds [ms] must elapse to switch corresponding fan off. (when the temperature was below defined range). +pwm[1-4]_start_output-minimum fan speed (range 1 - 255) when spinning up +pwm[1-4]_step_output- rate of fan speed change (1 - 255) +pwm[1-4]_stop_output- minimum fan speed (range 1 - 255) when spinning down +pwm[1-4]_max_output - maximum fan speed (range 1 - 255), when the temperature + is above defined range. -Note: last two functions are influenced by other control bits, not yet exported +Note: last six functions are influenced by other control bits, not yet exported by the driver, so a change might not have any effect. Implementation Details |