diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/omap-usb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/omap-usb.txt | 40 |
1 files changed, 13 insertions, 27 deletions
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 57e71f6817d..38d9bb8507c 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -3,9 +3,6 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" - ti,hwmods : must be "usb_otg_hs" - - ti,has-mailbox : to specify that omap uses an external mailbox - (in control module) to communicate with the musb core during device connect - and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - num-eps : Specifies the number of endpoints. This is also a @@ -19,6 +16,9 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply up to 100mA when operating in host mode. - usb-phy : the phandle for the PHY device + - phys : the phandle for the PHY device (used by generic PHY framework) + - phy-names : the names of the PHY corresponding to the PHYs present in the + *phy* phandle. Optional properties: - ctrl-module : phandle of the control module this glue uses to write to @@ -28,11 +28,12 @@ SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; ti,hwmods = "usb_otg_hs"; - ti,has-mailbox; multipoint = <1>; num-eps = <16>; ram-bits = <12>; ctrl-module = <&omap_control_usb>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; }; Board specific device node entry @@ -43,7 +44,9 @@ Board specific device node entry }; OMAP DWC3 GLUE - - compatible : Should be "ti,dwc3" + - compatible : Should be + * "ti,dwc3" for OMAP5 and DRA7 + * "ti,am437x-dwc3" for AM437x - ti,hwmods : Should be "usb_otg_ss" - reg : Address and length of the register set for the device. - interrupts : The irq number of this device that is used to interrupt the @@ -53,6 +56,11 @@ OMAP DWC3 GLUE It should be set to "1" for HW mode and "2" for SW mode. - ranges: the child address space are mapped 1:1 onto the parent address space +Optional Properties: + - extcon : phandle for the extcon device omap dwc3 uses to detect + connect/disconnect events. + - vbus-supply : phandle to the regulator device tree node if needed. + Sub-nodes: The dwc3 core should be added as subnode to omap dwc3 glue. - dwc3 : @@ -70,25 +78,3 @@ omap_dwc3 { ranges; }; -OMAP CONTROL USB - -Required properties: - - compatible: Should be "ti,omap-control-usb" - - reg : Address and length of the register set for the device. It contains - the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" - depending upon omap4 or omap5. - - reg-names: The names of the register addresses corresponding to the registers - filled in "reg". - - ti,type: This is used to differentiate whether the control module has - usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to - notify events to the musb core and omap5 has usb3 phy power register to - power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 - phy power. - -omap_control_usb: omap-control-usb@4a002300 { - compatible = "ti,omap-control-usb"; - reg = <0x4a002300 0x4>, - <0x4a00233c 0x4>; - reg-names = "control_dev_conf", "otghs_control"; - ti,type = <1>; -}; |