diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pwm')
20 files changed, 276 insertions, 47 deletions
diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt new file mode 100644 index 00000000000..02331b904d4 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt @@ -0,0 +1,33 @@ +Atmel PWM controller + +Required properties: + - compatible: should be one of: + - "atmel,at91sam9rl-pwm" + - "atmel,sama5d3-pwm" + - reg: physical base address and length of the controller's registers + - #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Example: + + pwm0: pwm@f8034000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xf8034000 0x400>; + #pwm-cells = <3>; + }; + + pwmleds { + compatible = "pwm-leds"; + + d1 { + label = "d1"; + pwms = <&pwm0 3 5000 0> + max-brightness = <255>; + }; + + d2 { + label = "d2"; + pwms = <&pwm0 1 5000 1> + max-brightness = <255>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt index de0eaed8665..8031148bcf8 100644 --- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt @@ -2,11 +2,9 @@ Atmel TCB PWM controller Required properties: - compatible: should be "atmel,tcb-pwm" -- #pwm-cells: Should be 3. The first cell specifies the per-chip index - of the PWM to use, the second cell is the period in nanoseconds and - bit 0 in the third cell is used to encode the polarity of PWM output. - Set bit 0 of the third cell in PWM specifier to 1 for inverse polarity & - set to 0 for normal polarity. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. - tc-block: The Timer Counter block to use as a PWM chip. Example: diff --git a/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt b/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt new file mode 100644 index 00000000000..8eae9fe7841 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt @@ -0,0 +1,21 @@ +Broadcom Kona PWM controller device tree bindings + +This controller has 6 channels. + +Required Properties : +- compatible: should contain "brcm,kona-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle + clock specifier pair for the external clock +- #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +pwm: pwm@3e01a000 { + compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm"; + reg = <0x3e01a000 0xc4>; + clocks = <&pwm_clk>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt new file mode 100644 index 00000000000..a183db48f91 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt @@ -0,0 +1,16 @@ +* Cirris Logic CLPS711X PWM controller + +Required properties: +- compatible: Shall contain "cirrus,clps711x-pwm". +- reg: Physical base address and length of the controller's registers. +- clocks: phandle + clock specifier pair of the PWM reference clock. +- #pwm-cells: Should be 1. The cell specifies the index of the channel. + +Example: + pwm: pwm@80000400 { + compatible = "cirrus,ep7312-pwm", + "cirrus,clps711x-pwm"; + reg = <0x80000400 0x4>; + clocks = <&clks 8>; + #pwm-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt index 8522bfbccfd..b50d7a6d9d7 100644 --- a/Documentation/devicetree/bindings/pwm/imx-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -3,8 +3,8 @@ Freescale i.MX PWM controller Required properties: - compatible: should be "fsl,<soc>-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. - interrupts: The interrupt for the pwm controller Example: diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt index 9e3f8f1d46a..96cdde5f620 100644 --- a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt @@ -3,8 +3,8 @@ Freescale MXS PWM controller Required properties: - compatible: should be "fsl,imx23-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. - fsl,pwm-number: the number of PWM devices Example: diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt index 01438ecd662..c7ea9d4a988 100644 --- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -5,9 +5,14 @@ Required properties: - "nvidia,tegra20-pwm" - "nvidia,tegra30-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: On Tegra the number of cells used to specify a PWM is 2. The - first cell specifies the per-chip index of the PWM to use and the second - cell is the period in nanoseconds. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pwm Example: @@ -15,4 +20,7 @@ Example: compatible = "nvidia,tegra20-pwm"; reg = <0x7000a000 0x100>; #pwm-cells = <2>; + clocks = <&tegra_car 17>; + resets = <&tegra_car 17>; + reset-names = "pwm"; }; diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt index 1e3dfe7a489..f84ec9d291e 100644 --- a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt @@ -3,8 +3,8 @@ NXP PCA9685 16-channel 12-bit PWM LED controller Required properties: - compatible: "nxp,pca9685-pwm" - - #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. + - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of + the cells format. The index 16 is the ALLCALL channel, that sets all PWM channels at the same time. diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt new file mode 100644 index 00000000000..0bda229a617 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -0,0 +1,35 @@ +Freescale FlexTimer Module (FTM) PWM controller + +Required properties: +- compatible: Should be "fsl,vf610-ftm-pwm". +- reg: Physical base address and length of the controller's registers +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. +- clock-names: Should include the following module clock source entries: + "ftm_sys" (module clock, also can be used as counter clock), + "ftm_ext" (external counter clock), + "ftm_fix" (fixed counter clock), + "ftm_cnt_clk_en" (external and fixed counter clock enable/disable). +- clocks: Must contain a phandle and clock specifier for each entry in + clock-names, please see clock/clock-bindings.txt for details of the property + values. +- pinctrl-names: Must contain a "default" entry. +- pinctrl-NNN: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. + + +Example: + +pwm0: pwm@40038000 { + compatible = "fsl,vf610-ftm-pwm"; + reg = <0x40038000 0x1000>; + #pwm-cells = <3>; + clock-names = "ftm_sys", "ftm_ext", + "ftm_fix", "ftm_cnt_clk_en"; + clocks = <&clks VF610_CLK_FTM0>, + <&clks VF610_CLK_FTM0_EXT_SEL>, + <&clks VF610_CLK_FTM0_FIX_SEL>, + <&clks VF610_CLK_FTM0_EXT_FIX_EN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_1>; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt new file mode 100644 index 00000000000..7bd9d3b12ce --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt @@ -0,0 +1,58 @@ +TI/National Semiconductor LP3943 PWM controller + +Required properties: + - compatible: "ti,lp3943-pwm" + - #pwm-cells: Should be 2. See pwm.txt in this directory for a + description of the cells format. + Note that this hardware limits the period length to the + range 6250~1600000. + - ti,pwm0 or ti,pwm1: Output pin number(s) for PWM channel 0 or 1. + 0 = output 0 + 1 = output 1 + . + . + 15 = output 15 + +Example: +PWM 0 is for RGB LED brightness control +PWM 1 is for brightness control of LP8557 backlight device + +&i2c3 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + /* + * PWM 0 : output 8, 9 and 10 + * PWM 1 : output 15 + */ + pwm3943: pwm { + compatible = "ti,lp3943-pwm"; + #pwm-cells = <2>; + ti,pwm0 = <8 9 10>; + ti,pwm1 = <15>; + }; + }; + +}; + +/* LEDs control with PWM 0 of LP3943 */ +pwmleds { + compatible = "pwm-leds"; + rgb { + label = "indi::rgb"; + pwms = <&pwm3943 0 10000>; + max-brightness = <255>; + }; +}; + +&i2c4 { + /* Backlight control with PWM 1 of LP3943 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + pwms = <&pwm3943 1 10000>; + pwm-names = "lp8557"; + }; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt index ac67c687a32..5538de9c200 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt @@ -15,17 +15,23 @@ Required properties: samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, Exynos4210 rev0 SoCs samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, - Exynos4x12 and Exynos5250 SoCs + Exynos4x12, Exynos5250 and Exynos5420 SoCs - reg: base address and size of register area - interrupts: list of timer interrupts (one interrupt per timer, starting at timer 0) -- #pwm-cells: number of cells used for PWM specifier - must be 3 - the specifier format is as follows: - - phandle to PWM controller node - - index of PWM channel (from 0 to 4) - - PWM signal period in nanoseconds - - bitmask of optional PWM flags: - 0x1 - invert PWM signal +- clock-names: should contain all following required clock names: + - "timers" - PWM base clock used to generate PWM signals, + and any subset of following optional clock names: + - "pwm-tclk0" - first external PWM clock source, + - "pwm-tclk1" - second external PWM clock source. + Note that not all IP variants allow using all external clock sources. + Refer to SoC documentation to learn which clock source configurations + are available. +- clocks: should contain clock specifiers of all clocks, which input names + have been specified in clock-names property, in same order. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. Optional properties: - samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular @@ -38,6 +44,8 @@ Example: reg = <0x7f006000 0x1000>; interrupt-parent = <&vic0>; interrupts = <23>, <24>, <25>, <27>, <28>; + clocks = <&clock 67>; + clock-names = "timers"; samsung,pwm-outputs = <0>, <1>; #pwm-cells = <3>; } diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt index 681afad7377..fb81179dce3 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -4,11 +4,9 @@ Required properties: - compatible: Must be "ti,<soc>-ecap". for am33xx - compatible = "ti,am33xx-ecap"; for da850 - compatible = "ti,da850-ecap", "ti,am33xx-ecap"; -- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. - First cell specifies the per-chip index of the PWM to use, the second - cell is the period in nanoseconds and bit 0 in the third cell is used to - encode the polarity of PWM output. Set bit 0 of the third in PWM specifier - to 1 for inverse polarity & set to 0 for normal polarity. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The PWM channel index ranges from 0 to 4. The only third + cell flag supported by this binding is PWM_POLARITY_INVERTED. - reg: physical base address and size of the registers map. Optional properties: diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt index 337c6fc65d3..9c100b2c5b2 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -4,11 +4,9 @@ Required properties: - compatible: Must be "ti,<soc>-ehrpwm". for am33xx - compatible = "ti,am33xx-ehrpwm"; for da850 - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; -- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. - First cell specifies the per-chip index of the PWM to use, the second - cell is the period in nanoseconds and bit 0 in the third cell is used to - encode the polarity of PWM output. Set bit 0 of the third in PWM specifier - to 1 for inverse polarity & set to 0 for normal polarity. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. - reg: physical base address and size of the registers map. Optional properties: diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt index 06e67247859..8556263b850 100644 --- a/Documentation/devicetree/bindings/pwm/pwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -43,13 +43,14 @@ because the name "backlight" would be used as fallback anyway. pwm-specifier typically encodes the chip-relative PWM number and the PWM period in nanoseconds. -Optionally, the pwm-specifier can encode a number of flags in a third cell: -- bit 0: PWM signal polarity (0: normal polarity, 1: inverse polarity) +Optionally, the pwm-specifier can encode a number of flags (defined in +<dt-bindings/pwm/pwm.h>) in a third cell: +- PWM_POLARITY_INVERTED: invert the PWM signal polarity Example with optional PWM specifier for inverse polarity bl: backlight { - pwms = <&pwm 0 5000000 1>; + pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>; pwm-names = "backlight"; }; diff --git a/Documentation/devicetree/bindings/pwm/pxa-pwm.txt b/Documentation/devicetree/bindings/pwm/pxa-pwm.txt new file mode 100644 index 00000000000..5ae9f1e3c33 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pxa-pwm.txt @@ -0,0 +1,30 @@ +Marvell PWM controller + +Required properties: +- compatible: should be one or more of: + - "marvell,pxa250-pwm" + - "marvell,pxa270-pwm" + - "marvell,pxa168-pwm" + - "marvell,pxa910-pwm" +- reg: Physical base address and length of the registers used by the PWM channel + Note that one device instance must be created for each PWM that is used, so the + length covers only the register window for one PWM output, not that of the + entire PWM controller. Currently length is 0x10 for all supported devices. +- #pwm-cells: Should be 1. This cell is used to specify the period in + nanoseconds. + +Example PWM device node: + +pwm0: pwm@40b00000 { + compatible = "marvell,pxa250-pwm"; + reg = <0x40b00000 0x10>; + #pwm-cells = <1>; +}; + +Example PWM client node: + +backlight { + compatible = "pwm-backlight"; + pwms = <&pwm0 5000000>; + ... +} diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt new file mode 100644 index 00000000000..b067e84a94b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -0,0 +1,28 @@ +* Renesas R-Car Timer Pulse Unit PWM Controller + +Required Properties: + + - compatible: should be one of the following. + - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller. + - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. + - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. + - "renesas,tpu-sh7372": for SH7372 (SH-Mobile AP4) compatible PWM controller. + - "renesas,tpu": for generic R-Car TPU PWM controller. + + - reg: Base address and length of each memory resource used by the PWM + controller hardware module. + + - #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. + +Please refer to pwm.txt in this directory for details of the common PWM bindings +used by client devices. + +Example: R8A7740 (R-Car A1) TPU controller node + + tpu: pwm@e6600000 { + compatible = "renesas,tpu-r8a7740", "renesas,tpu"; + reg = <0xe6600000 0x100>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt index 3ac779d8338..b486de2c3fe 100644 --- a/Documentation/devicetree/bindings/pwm/spear-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -5,9 +5,8 @@ Required properties: - "st,spear320-pwm" - "st,spear1340-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: number of cells used to specify PWM which is fixed to 2 on - SPEAr. The first cell specifies the per-chip index of the PWM to use and - the second cell is the period in nanoseconds. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. Example: diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt index 2943ee5fce0..4e32bee1120 100644 --- a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -6,8 +6,8 @@ On TWL6030 series: PWM0 and PWM1 Required properties: - compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" -- #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. Example: diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt index cb64f3acc10..9f4b4609078 100644 --- a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -6,8 +6,8 @@ On TWL6030 series: LED PWM (mainly used as charging indicator LED) Required properties: - compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" -- #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. Example: diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt index d21d82d2985..a76390e6df2 100644 --- a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -3,11 +3,9 @@ VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller Required properties: - compatible: should be "via,vt8500-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. - First cell specifies the per-chip index of the PWM to use, the second - cell is the period in nanoseconds and bit 0 in the third cell is used to - encode the polarity of PWM output. Set bit 0 of the third in PWM specifier - to 1 for inverse polarity & set to 0 for normal polarity. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. - clocks: phandle to the PWM source clock Example: |