diff options
Diffstat (limited to 'Documentation/devicetree/bindings/i2c')
22 files changed, 578 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt index 1ac8ea8ade1..bfeabb84394 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -8,6 +8,12 @@ the standard I2C multi-master rules. Using GPIOs is generally useful in the case where there is a device on the bus that has errata and/or bugs that makes standard multimaster mode not feasible. +Note that this scheme works well enough but has some downsides: +* It is nonstandard (not using standard I2C multimaster) +* Having two masters on a bus in general makes it relatively hard to debug + problems (hard to tell if i2c issues were caused by one master, another, or + some device on the bus). + Algorithm: diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index b689a0d9441..388f0a275fb 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-at91.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt @@ -9,8 +9,10 @@ Required properties : - interrupts: interrupt number to the cpu. - #address-cells = <1>; - #size-cells = <0>; +- clocks: phandles to input clocks. Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 - Child nodes conforming to i2c bus binding Examples : @@ -21,6 +23,8 @@ i2c0: i2c@fff84000 { interrupts = <12 4 6>; #address-cells = <1>; #size-cells = <0>; + clocks = <&twi0_clk>; + clock-frequency = <400000>; 24c512@50 { compatible = "24c512"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt new file mode 100644 index 00000000000..1b87b741fa8 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt @@ -0,0 +1,35 @@ +Broadcom Kona Family I2C +========================= + +This I2C controller is used in the following Broadcom SoCs: + + BCM11130 + BCM11140 + BCM11351 + BCM28145 + BCM28155 + +Required Properties +------------------- +- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c" +- reg: Physical base address and length of controller registers +- interrupts: The interrupt number used by the controller +- clocks: clock specifier for the kona i2c external clock +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Refer to clocks/clock-bindings.txt for generic clock consumer +properties. + +Example: + +i2c@3e016000 { + compatible = "brcm,bcm11351-i2c","brcm,kona-i2c"; + reg = <0x3e016000 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bsc1_clk>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt new file mode 100644 index 00000000000..7cb0b5608f4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt @@ -0,0 +1,24 @@ +Binding for the Cadence I2C controller + +Required properties: + - reg: Physical base address and size of the controller's register area. + - compatible: Compatibility string. Must be 'cdns,i2c-r1p10'. + - clocks: Input clock specifier. Refer to common clock bindings. + - interrupts: Interrupt specifier. Refer to interrupt bindings. + - #address-cells: Should be 1. + - #size-cells: Should be 0. + +Optional properties: + - clock-frequency: Desired operating frequency, in Hz, of the bus. + - clock-names: Input clock name, should be 'pclk'. + +Example: + i2c@e0004000 { + compatible = "cdns,i2c-r1p10"; + clocks = <&clkc 38>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xe0004000 0x1000>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt new file mode 100644 index 00000000000..898f030eba6 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt @@ -0,0 +1,39 @@ +I2C bus that tunnels through the ChromeOS EC (cros-ec) +====================================================== +On some ChromeOS board designs we've got a connection to the EC (embedded +controller) but no direct connection to some devices on the other side of +the EC (like a battery and PMIC). To get access to those devices we need +to tunnel our i2c commands through the EC. + +The node for this device should be under a cros-ec node like google,cros-ec-spi +or google,cros-ec-i2c. + + +Required properties: +- compatible: google,cros-ec-i2c-tunnel +- google,remote-bus: The EC bus we'd like to talk to. + +Optional child nodes: +- One node per I2C device connected to the tunnelled I2C bus. + + +Example: + cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + #address-cells = <1>; + #size-cells = <0>; + + google,remote-bus = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + }; + } diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index 7fd7fa25e9b..5199b0c8cf7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -14,6 +14,12 @@ Optional properties : - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer. + - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds. + This value which is by default 300ns is used to compute the tLOW period. + + - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds. + This value which is by default 300ns is used to compute the tHIGH period. + Example : i2c@f0000 { @@ -34,4 +40,6 @@ Example : interrupts = <12 1>; clock-frequency = <400000>; i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <300>; + i2c-scl-falling-time-ns = <300>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt new file mode 100644 index 00000000000..fc15ac51943 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt @@ -0,0 +1,34 @@ +* Energymicro efm32 i2c controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "energymicro,efm32-i2c" + - interrupts : the interrupt number + - clocks : reference to the module clock + +Recommended properties : + + - clock-frequency : maximal I2C bus clock frequency in Hz. + - efm32,location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 6] + +Example: + i2c0: i2c@4000a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "energymicro,efm32-i2c"; + reg = <0x4000a000 0x400>; + interrupts = <9>; + clocks = <&cmu clk_HFPERCLKI2C0>; + clock-frequency = <100000>; + status = "ok"; + efm32,location = <3>; + + eeprom@50 { + compatible = "microchip,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt new file mode 100644 index 00000000000..d4745e31f5c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -0,0 +1,51 @@ +* Samsung's High Speed I2C controller + +The Samsung's High Speed I2C controller is used to interface with I2C devices +at various speeds ranging from 100khz to 3.4Mhz. + +Required properties: + - compatible: value should be. + -> "samsung,exynos5-hsi2c", (DEPRECATED) + for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5250-hsi2c", for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5260-hsi2c", for i2c compatible with HSI2C available + on Exynos5260 SoCs. + + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + + - Pinctrl: + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - clock-frequency: Desired operating frequency in Hz of the bus. + -> If not specified, the bus operates in fast-speed mode at + at 100khz. + -> If specified, the bus operates in high-speed mode only if the + clock-frequency is >= 1Mhz. + +Example: + +hsi2c@12ca0000 { + compatible = "samsung,exynos5250-hsi2c"; + reg = <0x12ca0000 0x100>; + interrupts = <56>; + clock-frequency = <100000>; + + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 3614242e773..4a8513e4474 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -1,7 +1,10 @@ * Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX Required properties: -- compatible : Should be "fsl,<chip>-i2c" +- compatible : + - "fsl,imx1-i2c" for I2C compatible with the one integrated on i.MX1 SoC + - "fsl,imx21-i2c" for I2C compatible with the one integrated on i.MX21 SoC + - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC - reg : Should contain I2C/HS-I2C registers location and length - interrupts : Should contain I2C/HS-I2C interrupt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt new file mode 100644 index 00000000000..34a3fb6f848 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -0,0 +1,50 @@ +* NXP PCA954x I2C bus switch + +Required Properties: + + - compatible: Must contain one of the following. + "nxp,pca9540", "nxp,pca9542", "nxp,pca9543", "nxp,pca9544", + "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548" + + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - Standard I2C mux properties. See i2c-mux.txt in this directory. + - I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the reset input. + + +Example: + + i2c-switch@74 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + eeprom@54 { + compatible = "at,24c08"; + reg = <0x54>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt index 6113f9275f4..5c30026921a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -4,7 +4,16 @@ Required properties : - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c" + - compatible : Should be either: + - "allwinner,sun4i-a10-i2c" + - "allwinner,sun6i-a31-i2c" + - "marvell,mv64xxx-i2c" + - "marvell,mv78230-i2c" + - "marvell,mv78230-a0-i2c" + * Note: Only use "marvell,mv78230-a0-i2c" for a + very rare, initial version of the SoC which + had broken offload support. Linux + auto-detects this and sets it appropriately. - interrupts : The interrupt number Optional properties : @@ -12,6 +21,10 @@ Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the default frequency is 100kHz + - resets : phandle to the parent reset controller. Mandatory + whenever you're using the "allwinner,sun6i-a31-i2c" + compatible. + Examples: i2c@11000 { @@ -20,3 +33,12 @@ Examples: interrupts = <29>; clock-frequency = <100000>; }; + +For the Armada XP: + + i2c@11000 { + compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c"; + reg = <0x11000 0x100>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-omap.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt index 56564aa4b44..7e49839d412 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-omap.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt @@ -1,7 +1,8 @@ I2C for OMAP platforms Required properties : -- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c" +- compatible : Must be "ti,omap2420-i2c", "ti,omap2430-i2c", "ti,omap3-i2c" + or "ti,omap4-i2c" - ti,hwmods : Must be "i2c<n>", n being the instance number (1-based) - #address-cells = <1>; - #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt new file mode 100644 index 00000000000..16b3e07aa98 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -0,0 +1,32 @@ +I2C for R-Car platforms + +Required properties: +- compatible: Must be one of + "renesas,i2c-rcar" + "renesas,i2c-r8a7778" + "renesas,i2c-r8a7779" + "renesas,i2c-r8a7790" + "renesas,i2c-r8a7791" + "renesas,i2c-r8a7792" + "renesas,i2c-r8a7793" + "renesas,i2c-r8a7794" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt specifier. + +Optional properties: +- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this + propoerty indicates the default frequency 100 kHz. +- clocks: clock specifier. + +Examples : + +i2c0: i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C0>; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-riic.txt b/Documentation/devicetree/bindings/i2c/i2c-riic.txt new file mode 100644 index 00000000000..0bcc4716c31 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-riic.txt @@ -0,0 +1,29 @@ +Device tree configuration for Renesas RIIC driver + +Required properties: +- compatible : "renesas,riic-<soctype>". "renesas,riic-rz" as fallback +- reg : address start and address range size of device +- interrupts : 8 interrupts (TEI, RI, TI, SPI, STI, NAKI, ALI, TMOI) +- clock-frequency : frequency of bus clock in Hz +- #address-cells : should be <1> +- #size-cells : should be <0> + +Pinctrl properties might be needed, too. See there. + +Example: + + i2c0: i2c@fcfee000 { + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee000 0x44>; + interrupts = <0 157 IRQ_TYPE_LEVEL_HIGH>, + <0 158 IRQ_TYPE_EDGE_RISING>, + <0 159 IRQ_TYPE_EDGE_RISING>, + <0 160 IRQ_TYPE_LEVEL_HIGH>, + <0 161 IRQ_TYPE_LEVEL_HIGH>, + <0 162 IRQ_TYPE_LEVEL_HIGH>, + <0 163 IRQ_TYPE_LEVEL_HIGH>, + <0 164 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 index 00000000000..dde6c22ce91 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -0,0 +1,42 @@ +* Rockchip RK3xxx I2C controller + +This driver interfaces with the native I2C controller present in Rockchip +RK3xxx SoCs. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or + "rockchip,rk3288-i2c". + - interrupts : interrupt number + - clocks : parent clock + +Required on RK3066, RK3188 : + + - rockchip,grf : the phandle of the syscon node for the general register + file (GRF) + - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) + is also required. + +Optional properties : + + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. + +Example: + +aliases { + i2c0 = &i2c0; +} + +i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + rockchip,grf = <&grf>; + + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index 296eb453612..278de8e64bb 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -10,6 +10,8 @@ Required properties: inside HDMIPHY block found on several samsung SoCs (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used on EXYNOS5440 which does not need GPIO configuration. + (e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as + a host to SATA PHY controller on an internal bus. - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt new file mode 100644 index 00000000000..d2153ce36fa --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -0,0 +1,26 @@ +Device tree configuration for Renesas IIC (sh_mobile) driver + +Required properties: +- compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback +- reg : address start and address range size of device +- interrupts : interrupt of device +- clocks : clock for device +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset. + +Pinctrl properties might be needed, too. See there. + +Example: + + iic0: i2c@e6500000 { + compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + reg = <0 0xe6500000 0 0x425>; + interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_IIC0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt new file mode 100644 index 00000000000..437e0db3823 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -0,0 +1,41 @@ +ST SSC binding, for I2C mode operation + +Required properties : +- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- clock-names: Must contain "ssc". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. +- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is + allowed through the deglitch circuit. In units of us. +- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is + allowed through the deglitch circuit. In units of us. +- A pinctrl state named "idle" could be defined to set pins in idle state + when I2C instance is not performing a transfer. +- A pinctrl state named "sleep" could be defined to set pins in sleep state + when driver enters in suspend. + + + +Example : + +i2c0: i2c@fed40000 { + compatible = "st,comms-ssc4-i2c"; + reg = <0xfed40000 0x110>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ssc"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; + st,i2c-min-scl-pulse-width-us = <0>; + st,i2c-min-sda-pulse-width-us = <5>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt new file mode 100644 index 00000000000..6b765485af7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt @@ -0,0 +1,41 @@ + +* Allwinner P2WI (Push/Pull 2 Wire Interface) controller + +Required properties : + + - reg : Offset and length of the register set for the device. + - compatible : Should one of the following: + - "allwinner,sun6i-a31-p2wi" + - interrupts : The interrupt line connected to the P2WI peripheral. + - clocks : The gate clk connected to the P2WI peripheral. + - resets : The reset line connected to the P2WI peripheral. + +Optional properties : + + - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the +default frequency is 100kHz + +A P2WI may contain one child node encoding a P2WI slave device. + +Slave device properties: + Required properties: + - reg : the I2C slave address used during the initialization + process to switch from I2C to P2WI mode + +Example: + + p2wi@01f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <6000000>; + resets = <&apb0_rst 3>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt index ef77cc7a0e4..87507e9ce6d 100644 --- a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt @@ -39,12 +39,23 @@ Required properties: - interrupts: Should contain I2C controller interrupts. - address-cells: Address cells for I2C device address. - size-cells: Size of the I2C device address. -- clocks: Clock ID as per - Documentation/devicetree/bindings/clock/tegra<chip-id>.txt - for I2C controller. -- clock-names: Name of the clock: - Tegra20/Tegra30 I2C controller: "div-clk and "fast-clk". - Tegra114 I2C controller: "div-clk". +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + Tegra20/Tegra30: + - div-clk + - fast-clk + Tegra114: + - div-clk +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - i2c +- dmas: Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names: Must include the following entries: + - rx + - tx Example: @@ -56,5 +67,9 @@ Example: #size-cells = <0>; clocks = <&tegra_car 12>, <&tegra_car 124>; clock-names = "div-clk", "fast-clk"; + resets = <&tegra_car 12>; + reset-names = "i2c"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt new file mode 100644 index 00000000000..dc71754a56a --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt @@ -0,0 +1,40 @@ +Qualcomm Universal Peripheral (QUP) I2C controller + +Required properties: + - compatible: Should be: + * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064. + * "qcom,i2c-qup-v2.1.1" for 8974 v1. + * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later. + - reg: Should contain QUP register address and length. + - interrupts: Should contain I2C interrupt. + + - clocks: A list of phandles + clock-specifiers, one for each entry in + clock-names. + - clock-names: Should contain: + * "core" for the core clock + * "iface" for the AHB clock + + - #address-cells: Should be <1> Address cells for i2c device address + - #size-cells: Should be <0> as i2c addresses have no size component + +Optional properties: + - clock-frequency: Should specify the desired i2c bus clock frequency in Hz, + defaults to 100kHz if omitted. + +Child nodes should conform to i2c bus binding. + +Example: + + i2c@f9924000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9924000 0x1000>; + interrupts = <0 96 0>; + + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <355000>; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index ad6a73852f0..bef86e57c38 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -13,9 +13,26 @@ ad,ad7414 SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert an ad,adm9240 ADM9240: Complete System Hardware Monitor for uProcessor-Based Systems adi,adt7461 +/-1C TDM Extended Temp Range I.C adt7461 +/-1C TDM Extended Temp Range I.C +adi,adt7473 +/-1C TDM Extended Temp Range I.C +adi,adt7475 +/-1C TDM Extended Temp Range I.C +adi,adt7476 +/-1C TDM Extended Temp Range I.C +adi,adt7490 +/-1C TDM Extended Temp Range I.C at,24c08 i2c serial eeprom (24cxx) +atmel,24c00 i2c serial eeprom (24cxx) +atmel,24c01 i2c serial eeprom (24cxx) atmel,24c02 i2c serial eeprom (24cxx) +atmel,24c04 i2c serial eeprom (24cxx) +atmel,24c16 i2c serial eeprom (24cxx) +atmel,24c32 i2c serial eeprom (24cxx) +atmel,24c64 i2c serial eeprom (24cxx) +atmel,24c128 i2c serial eeprom (24cxx) +atmel,24c256 i2c serial eeprom (24cxx) +atmel,24c512 i2c serial eeprom (24cxx) +atmel,24c1024 i2c serial eeprom (24cxx) +atmel,at97sc3204t i2c trusted platform module (TPM) +capella,cm32181 CM32181: Ambient Light Sensor catalyst,24c32 i2c serial eeprom +cirrus,cs42l51 Cirrus Logic CS42L51 audio codec dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock dallas,ds1338 I2C RTC with 56-Byte NV RAM dallas,ds1339 I2C Serial Real-Time Clock @@ -35,15 +52,20 @@ fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec +gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) +isl,isl12057 Intersil ISL12057 I2C RTC Chip maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor +national,lm85 Temperature sensor with integrated fan control national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface +nuvoton,npct501 i2c trusted platform module (TPM) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar @@ -53,6 +75,7 @@ plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch ramtron,24c64 i2c serial eeprom (24cxx) ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sii,s35390a 2-wire CMOS real-time clock st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm @@ -61,3 +84,4 @@ taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor +winbond,wpct301 i2c trusted platform module (TPM) |