diff options
Diffstat (limited to 'Documentation/DocBook/libata.tmpl')
| -rw-r--r-- | Documentation/DocBook/libata.tmpl | 26 |
1 files changed, 13 insertions, 13 deletions
diff --git a/Documentation/DocBook/libata.tmpl b/Documentation/DocBook/libata.tmpl index 8c5411cfeaf..d7fcdc5a437 100644 --- a/Documentation/DocBook/libata.tmpl +++ b/Documentation/DocBook/libata.tmpl @@ -22,8 +22,8 @@ <para> The contents of this file are subject to the Open Software License version 1.1 that can be found at - <ulink url="http://www.opensource.org/licenses/osl-1.1.txt">http://www.opensource.org/licenses/osl-1.1.txt</ulink> and is included herein - by reference. + <ulink url="http://fedoraproject.org/wiki/Licensing:OSL1.1">http://fedoraproject.org/wiki/Licensing:OSL1.1</ulink> + and is included herein by reference. </para> <para> @@ -677,7 +677,7 @@ and other resources, etc. <listitem> <para> - ATA_QCFLAG_ACTIVE is clared from qc->flags. + ATA_QCFLAG_ACTIVE is cleared from qc->flags. </para> </listitem> @@ -708,7 +708,7 @@ and other resources, etc. <listitem> <para> - qc->waiting is claread & completed (in that order). + qc->waiting is cleared & completed (in that order). </para> </listitem> @@ -918,7 +918,7 @@ and other resources, etc. <title>HSM violation</title> <para> This error is indicated when STATUS value doesn't match HSM - requirement during issuing or excution any ATA/ATAPI command. + requirement during issuing or execution any ATA/ATAPI command. </para> <itemizedlist> @@ -945,7 +945,7 @@ and other resources, etc. <listitem> <para> - !BSY && ERR after CDB tranfer starts but before the + !BSY && ERR after CDB transfer starts but before the last byte of CDB is transferred. ATA/ATAPI standard states that "The device shall not terminate the PACKET command with an error before the last byte of the command packet has @@ -1032,7 +1032,7 @@ and other resources, etc. <listitem> <para> This is indicated by ICRC bit in the ERROR register and - means that corruption occurred during data transfer. Upto + means that corruption occurred during data transfer. Up to ATA/ATAPI-7, the standard specifies that this bit is only applicable to UDMA transfers but ATA/ATAPI-8 draft revision 1f says that the bit may be applicable to multiword DMA and @@ -1045,12 +1045,12 @@ and other resources, etc. <term>ABRT error during data transfer or on completion</term> <listitem> <para> - Upto ATA/ATAPI-7, the standard specifies that ABRT could be + Up to ATA/ATAPI-7, the standard specifies that ABRT could be set on ICRC errors and on cases where a device is not able to complete a command. Combined with the fact that MWDMA - and PIO transfer errors aren't allowed to use ICRC bit upto + and PIO transfer errors aren't allowed to use ICRC bit up to ATA/ATAPI-7, it seems to imply that ABRT bit alone could - indicate tranfer errors. + indicate transfer errors. </para> <para> However, ATA/ATAPI-8 draft revision 1f removes the part @@ -1122,7 +1122,7 @@ and other resources, etc. <para> Depending on commands, not all STATUS/ERROR bits are applicable. These non-applicable bits are marked with - "na" in the output descriptions but upto ATA/ATAPI-7 + "na" in the output descriptions but up to ATA/ATAPI-7 no definition of "na" can be found. However, ATA/ATAPI-8 draft revision 1f describes "N/A" as follows. @@ -1163,7 +1163,7 @@ and other resources, etc. <para> Once sense data is acquired, this type of errors can be - handled similary to other SCSI errors. Note that sense data + handled similarly to other SCSI errors. Note that sense data may indicate ATA bus error (e.g. Sense Key 04h HARDWARE ERROR && ASC/ASCQ 47h/00h SCSI PARITY ERROR). In such cases, the error should be considered as an ATA bus error and @@ -1507,7 +1507,7 @@ and other resources, etc. <listitem> <para> - CHS set up with INITIALIZE DEVICE PARAMETERS (seldomly used) + CHS set up with INITIALIZE DEVICE PARAMETERS (seldom used) </para> </listitem> |