diff options
23 files changed, 1586 insertions, 37 deletions
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 91b7049affa..808c1543b0f 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -21,7 +21,8 @@ Required properties: Optional properties: - ti,no_idle_on_suspend: When present, it prevents the PM to idle the module during suspend. - +- ti,no-reset-on-init: When present, the module should not be reset at init +- ti,no-idle-on-init: When present, the module should not be idled at init Example: diff --git a/MAINTAINERS b/MAINTAINERS index 1f006f15668..cb1f2e022aa 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -6088,6 +6088,12 @@ L: linux-omap@vger.kernel.org S: Maintained F: drivers/gpio/gpio-omap.c +OMAP/NEWFLOW NANOBONE MACHINE SUPPORT +M: Mark Jackson <mpfj@newflow.co.uk> +L: linux-omap@vger.kernel.org +S: Maintained +F: arch/arm/boot/dts/am335x-nano.dts + OMFS FILESYSTEM M: Bob Copeland <me@bobcopeland.com> L: linux-karma-devel@lists.sourceforge.net diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f2ff6266f78..b590bcebaa6 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -197,6 +197,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ am335x-evmsk.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-nano.dtb \ am335x-base0033.dtb \ am3517-evm.dtb \ am3517_mt_ventoux.dtb \ diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index eabacf9b8c3..98742943617 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -119,6 +119,19 @@ }; }; }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "AM335x-EVM"; + ti,audio-codec = <&tlv320aic3106>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "LINE1L", "Line In", + "LINE1R", "Line In"; + }; }; &am33xx_pinmux { @@ -279,6 +292,15 @@ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */ >; }; + + am335x_evm_audio_pins: am335x_evm_audio_pins { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */ + 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + >; + }; }; &uart0 { @@ -373,6 +395,18 @@ compatible = "ti,tmp275"; reg = <0x48>; }; + + tlv320aic3106: tlv320aic3106@1b { + compatible = "ti,tlv320aic3106"; + reg = <0x1b>; + status = "okay"; + + /* Regulators */ + AVDD-supply = <&vaux2_reg>; + IOVDD-supply = <&vaux2_reg>; + DRVDD-supply = <&vaux2_reg>; + DVDD-supply = <&vbat>; + }; }; &lcdc { @@ -476,6 +510,22 @@ #include "tps65910.dtsi" +&mcasp1 { + pinctrl-names = "default"; + pinctrl-0 = <&am335x_evm_audio_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 2 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + &tps { vcc1-supply = <&vbat>; vcc2-supply = <&vbat>; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 5f12b28dd59..03febf85fd2 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -115,6 +115,17 @@ brightness-levels = <0 58 61 66 75 90 125 170 255>; default-brightness-level = <8>; }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "AM335x-EVMSK"; + ti,audio-codec = <&tlv320aic3106>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <24576000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT"; + }; }; &am33xx_pinmux { @@ -244,6 +255,15 @@ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) >; }; + + mcasp1_pins: mcasp1_pins { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + >; + }; }; &uart0 { @@ -291,6 +311,18 @@ st,max-limit-y = <550>; st,max-limit-z = <750>; }; + + tlv320aic3106: tlv320aic3106@1b { + compatible = "ti,tlv320aic3106"; + reg = <0x1b>; + status = "okay"; + + /* Regulators */ + AVDD-supply = <&vaux2_reg>; + IOVDD-supply = <&vaux2_reg>; + DRVDD-supply = <&vaux2_reg>; + DVDD-supply = <&vbat>; + }; }; &usb { @@ -433,3 +465,23 @@ &aes { status = "okay"; }; + +&gpio0 { + ti,no-reset-on-init; +}; + +&mcasp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp1_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 2 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi index 06eba076bfc..61962447931 100644 --- a/arch/arm/boot/dts/am335x-igep0033.dtsi +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -44,6 +44,13 @@ regulator-max-microvolt = <5000000>; regulator-boot-on; }; + + vmmc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &am33xx_pinmux { @@ -180,6 +187,12 @@ }; }; +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmc>; + bus-width = <4>; +}; + &uart0 { status = "okay"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts new file mode 100644 index 00000000000..9907b494b99 --- /dev/null +++ b/arch/arm/boot/dts/am335x-nano.dts @@ -0,0 +1,431 @@ +/* + * Copyright (C) 2013 Newflow Ltd - http://www.newflow.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "Newflow AM335x NanoBone"; + compatible = "ti,am33xx"; + + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + compatible = "gpio-leds"; + + led@0 { + label = "nanobone:green:usr1"; + gpios = <&gpio1 5 0>; + default-state = "off"; + }; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&misc_pins>; + + misc_pins: misc_pins { + pinctrl-single,pins = < + 0x15c (PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */ + >; + }; + + gpmc_pins: gpmc_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x20 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */ + 0x24 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */ + 0x28 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */ + 0x2c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */ + 0x30 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */ + 0x34 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */ + 0x38 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */ + 0x3c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */ + + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x80 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */ + 0x84 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */ + 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */ + + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */ + + 0xa4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */ + 0xac (PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */ + 0xbc (PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */ + + 0xe0 (PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */ + 0xe4 (PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */ + 0xe8 (PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */ + >; + }; + + i2c0_pins: i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + uart1_pins: uart1_pins { + pinctrl-single,pins = < + 0x178 (PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */ + 0x17c (PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */ + 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + 0x184 (PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */ + >; + }; + + uart2_pins: uart2_pins { + pinctrl-single,pins = < + 0xc0 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */ + 0xc4 (PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */ + 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ + 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ + >; + }; + + uart3_pins: uart3_pins { + pinctrl-single,pins = < + 0xc8 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */ + 0xcc (PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */ + 0x160 (PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */ + 0x164 (PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */ + >; + }; + + uart4_pins: uart4_pins { + pinctrl-single,pins = < + 0xd0 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */ + 0xd4 (PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */ + 0x168 (PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */ + 0x16c (PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */ + >; + }; + + uart5_pins: uart5_pins { + pinctrl-single,pins = < + 0xd8 (PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */ + 0x144 (PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */ + >; + }; + + mmc1_pins: mmc1_pins { + pinctrl-single,pins = < + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + 0x1e8 (PIN_INPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */ + 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18] */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; + rts-gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>; + rs485-rts-active-high; + rs485-rx-during-tx; + rs485-rts-delay = <1 1>; + linux,rs485-enabled-at-boot-time; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; + rts-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>; + rs485-rts-active-high; + rs485-rts-delay = <1 1>; + linux,rs485-enabled-at-boot-time; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + gpio@20 { + compatible = "mcp,mcp23017"; + reg = <0x20>; + }; + + tps: tps@24 { + reg = <0x24>; + }; + + eeprom@53 { + compatible = "mcp,24c02"; + reg = <0x53>; + pagesize = <8>; + }; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + status = "okay"; + gpmc,num-waitpins = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&gpmc_pins>; + + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x08000000>; /* CS0: NOR 128M */ + + nor@0,0 { + reg = <0 0x00000000 0x08000000>; + compatible = "cfi-flash"; + linux,mtd-name = "spansion,s29gl010p11t"; + bank-width = <2>; + + gpmc,mux-add-data = <2>; + + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <160>; + gpmc,cs-wr-off-ns = <160>; + gpmc,adv-on-ns = <10>; + gpmc,adv-rd-off-ns = <30>; + gpmc,adv-wr-off-ns = <30>; + gpmc,oe-on-ns = <40>; + gpmc,oe-off-ns = <160>; + gpmc,we-on-ns = <40>; + gpmc,we-off-ns = <160>; + gpmc,rd-cycle-ns = <160>; + gpmc,wr-cycle-ns = <160>; + gpmc,access-ns = <150>; + gpmc,page-burst-access-ns = <10>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-delay-ns = <20>; + gpmc,wr-data-mux-bus-ns = <70>; + gpmc,wr-access-ns = <80>; + + #address-cells = <1>; + #size-cells = <1>; + + /* + MTD partition table + =================== + +------------+-->0x00000000-> U-Boot start + | | + | |-->0x000BFFFF-> U-Boot end + | |-->0x000C0000-> ENV1 start + | | + | |-->0x000DFFFF-> ENV1 end + | |-->0x000E0000-> ENV2 start + | | + | |-->0x000FFFFF-> ENV2 end + | |-->0x00100000-> Kernel start + | | + | |-->0x004FFFFF-> Kernel end + | |-->0x00500000-> File system start + | | + | |-->0x014FFFFF-> File system end + | |-->0x01500000-> User data start + | | + | |-->0x03FFFFFF-> User data end + | |-->0x04000000-> Data storage start + | | + +------------+-->0x08000000-> NOR end (Free end) + */ + partition@0 { + label = "boot"; + reg = <0x00000000 0x000c0000>; /* 768KB */ + }; + + partition@1 { + label = "env1"; + reg = <0x000c0000 0x00020000>; /* 128KB */ + }; + + partition@2 { + label = "env2"; + reg = <0x000e0000 0x00020000>; /* 128KB */ + }; + + partition@3 { + label = "kernel"; + reg = <0x00100000 0x00400000>; /* 4MB */ + }; + + partition@4 { + label = "rootfs"; + reg = <0x00500000 0x01000000>; /* 16MB */ + }; + + partition@5 { + label = "user"; + reg = <0x01500000 0x02b00000>; /* 43MB */ + }; + + partition@6 { + label = "data"; + reg = <0x04000000 0x04000000>; /* 64MB */ + }; + }; +}; + +&mac { + dual_emac = <1>; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + dual_emac_res_vlan = <1>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + dual_emac_res_vlan = <2>; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&ldo4_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + bus-width = <4>; + cd-gpios = <&gpio3 8 0>; + wp-gpios = <&gpio3 18 0>; +}; + +#include "tps65217.dtsi" + +&tps { + regulators { + dcdc1_reg: regulator@0 { + /* +1.5V voltage with ±4% tolerance */ + regulator-min-microvolt = <1450000>; + regulator-max-microvolt = <1550000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <915000>; + regulator-max-microvolt = <1140000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <915000>; + regulator-max-microvolt = <1140000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + /* +1.8V voltage with ±4% tolerance */ + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <1870000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + /* +3.3V voltage with ±4% tolerance */ + regulator-min-microvolt = <3175000>; + regulator-max-microvolt = <3430000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + /* +1.8V voltage with ±4% tolerance */ + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <1870000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + /* +3.3V voltage with ±4% tolerance */ + regulator-min-microvolt = <3175000>; + regulator-max-microvolt = <3430000>; + regulator-boot-on; + regulator-always-on; + }; + }; +}; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 7db3c81d156..0ca13ad92fa 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -18,6 +18,9 @@ interrupt-parent = <&intc>; aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; @@ -413,7 +416,7 @@ ti,hwmods = "usb_otg_hs"; status = "disabled"; - ctrl_mod: control@44e10000 { + usb_ctrl_mod: control@44e10000 { compatible = "ti,am335x-usb-ctrl-module"; reg = <0x44e10620 0x10 0x44e10648 0x4>; @@ -426,7 +429,7 @@ reg = <0x47401300 0x100>; reg-names = "phy"; status = "disabled"; - ti,ctrl_mod = <&ctrl_mod>; + ti,ctrl_mod = <&usb_ctrl_mod>; }; usb0: usb@47401000 { @@ -474,7 +477,7 @@ reg = <0x47401b00 0x100>; reg-names = "phy"; status = "disabled"; - ti,ctrl_mod = <&ctrl_mod>; + ti,ctrl_mod = <&usb_ctrl_mod>; }; usb1: usb@47401800 { @@ -674,6 +677,7 @@ reg = <0x44d00000 0x4000 /* M3 UMEM */ 0x44d80000 0x2000>; /* M3 DMEM */ ti,hwmods = "wkup_m3"; + ti,no-reset-on-init; }; elm: elm@48080000 { @@ -713,6 +717,7 @@ gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; + ti,no-idle-on-init; reg = <0x50000000 0x2000>; interrupts = <100>; gpmc,num-cs = <7>; @@ -740,5 +745,33 @@ <&edma 5>; dma-names = "tx", "rx"; }; + + mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 8>, + <&edma 9>; + dma-names = "tx", "rx"; + }; + + mcasp1: mcasp@4803C000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp1"; + reg = <0x4803C000 0x2000>, + <0x46400000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <82>, <83>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 10>, + <&edma 11>; + dma-names = "tx", "rx"; + }; }; }; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index a403172430b..974d103ab3b 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -18,7 +18,12 @@ aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1; }; cpus { @@ -39,11 +44,42 @@ <0x48240100 0x0100>; }; + l2-cache-controller@48242000 { + compatible = "arm,pl310-cache"; + reg = <0x48242000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + am43xx_pinmux: pinmux@44e10800 { + compatible = "pinctrl-single"; + reg = <0x44e10800 0x31c>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0xffffffff>; + }; + ocp { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; + ti,hwmods = "l3_main"; + + edma: edma@49000000 { + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + reg = <0x49000000 0x10000>, + <0x44e10f90 0x10>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <64>; + ti,edma-regions = <4>; + ti,edma-slots = <256>; + }; uart0: serial@44e09000 { compatible = "ti,am4372-uart","ti,omap2-uart"; @@ -92,6 +128,18 @@ status = "disabled"; }; + mailbox: mailbox@480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + ti,mbox-names = "wkup_m3"; + ti,mbox-data = <0 0 0 0>; + status = "disabled"; + }; + timer1: timer@44e31000 { compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms"; reg = <0x44e31000 0x400>; @@ -203,7 +251,6 @@ reg = <0x44e35000 0x1000>; interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "wd_timer2"; - status = "disabled"; }; gpio0: gpio@44e07000 { @@ -318,6 +365,40 @@ status = "disabled"; }; + mmc1: mmc@48060000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x48060000 0x1000>; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + mmc2: mmc@481d8000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x481d8000 0x1000>; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&edma 2 + &edma 3>; + dma-names = "tx", "rx"; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x47810000 0x1000>; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + spi1: spi@481a0000 { compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; reg = <0x481a0000 0x400>; @@ -366,50 +447,173 @@ GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <1>; ti,hwmods = "cpgmac0"; status = "disabled"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + ranges; + + davinci_mdio: mdio@4a101000 { + compatible = "ti,am4372-mdio","ti,davinci_mdio"; + reg = <0x4a101000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + status = "disabled"; + }; + + cpsw_emac0: slave@4a100200 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + + cpsw_emac1: slave@4a100300 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; }; epwmss0: epwmss@48300000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48300000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss0"; status = "disabled"; + + ecap0: ecap@48300100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; + status = "disabled"; + }; + + ehrpwm0: ehrpwm@48300200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48300200 0x80>; + ti,hwmods = "ehrpwm0"; + status = "disabled"; + }; }; epwmss1: epwmss@48302000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48302000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss1"; status = "disabled"; + + ecap1: ecap@48302100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48302100 0x80>; + ti,hwmods = "ecap1"; + status = "disabled"; + }; + + ehrpwm1: ehrpwm@48302200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48302200 0x80>; + ti,hwmods = "ehrpwm1"; + status = "disabled"; + }; }; epwmss2: epwmss@48304000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48304000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss2"; status = "disabled"; + + ecap2: ecap@48304100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48304100 0x80>; + ti,hwmods = "ecap2"; + status = "disabled"; + }; + + ehrpwm2: ehrpwm@48304200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48304200 0x80>; + ti,hwmods = "ehrpwm2"; + status = "disabled"; + }; }; epwmss3: epwmss@48306000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48306000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss3"; status = "disabled"; + + ehrpwm3: ehrpwm@48306200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48306200 0x80>; + ti,hwmods = "ehrpwm3"; + status = "disabled"; + }; }; epwmss4: epwmss@48308000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x48308000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss4"; status = "disabled"; + + ehrpwm4: ehrpwm@48308200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48308200 0x80>; + ti,hwmods = "ehrpwm4"; + status = "disabled"; + }; }; epwmss5: epwmss@4830a000 { compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; reg = <0x4830a000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; ti,hwmods = "epwmss5"; status = "disabled"; + + ehrpwm5: ehrpwm@4830a200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x4830a200 0x80>; + ti,hwmods = "ehrpwm5"; + status = "disabled"; + }; + }; + + sham: sham@53100000 { + compatible = "ti,omap5-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x300>; + dmas = <&edma 36>; + dma-names = "rx"; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; }; aes: aes@53501000 { @@ -417,6 +621,9 @@ ti,hwmods = "aes"; reg = <0x53501000 0xa0>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&edma 6 + &edma 5>; + dma-names = "tx", "rx"; }; des: des@53701000 { @@ -424,6 +631,37 @@ ti,hwmods = "des"; reg = <0x53701000 0xa0>; interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&edma 34 + &edma 33>; + dma-names = "tx", "rx"; + }; + + mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 8>, + <&edma 9>; + dma-names = "tx", "rx"; + }; + + mcasp1: mcasp@4803C000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp1"; + reg = <0x4803C000 0x2000>, + <0x46400000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <82>, <83>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 10>, + <&edma 11>; + dma-names = "tx", "rx"; }; }; }; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 74174d48f47..fbf9c4c7a94 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -11,8 +11,176 @@ /dts-v1/; #include "am4372.dtsi" +#include <dt-bindings/pinctrl/am43xx.h> +#include <dt-bindings/gpio/gpio.h> / { model = "TI AM43x EPOS EVM"; compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43"; + + vmmcsd_fixed: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + }; + + am43xx_pinmux: pinmux@44e10800 { + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + }; + + matrix_keypad: matrix_keypad@0 { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */ + &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */ + &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */ + &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */ + + col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */ + &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */ + &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */ + &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */ + + linux,keymap = <0x00000201 /* P1 */ + 0x01000204 /* P4 */ + 0x02000207 /* P7 */ + 0x0300020a /* NUMERIC_STAR */ + 0x00010202 /* P2 */ + 0x01010205 /* P5 */ + 0x02010208 /* P8 */ + 0x03010200 /* P0 */ + 0x00020203 /* P3 */ + 0x01020206 /* P6 */ + 0x02020209 /* P9 */ + 0x0302020b /* NUMERIC_POUND */ + 0x00030067 /* UP */ + 0x0103006a /* RIGHT */ + 0x0203006c /* DOWN */ + 0x03030069>; /* LEFT */ + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <16>; + phy-mode = "rmii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rmii"; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + at24@50 { + compatible = "at24,24c256"; + pagesize = <64>; + reg = <0x50>; + }; + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>; + + x-size = <1024>; + y-size = <768>; + }; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; }; diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 3abf5f41e5c..5babba0a3a7 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -269,3 +269,7 @@ vmmc-supply = <&mmc2_3v3>; bus-width = <8>; }; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index c01ef769761..d0df4c4e8b0 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -20,6 +20,11 @@ interrupt-parent = <&gic>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + i2c4 = &i2c5; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -32,10 +37,16 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a15"; reg = <0>; + + operating-points = < + /* kHz uV */ + 1000000 1060000 + 1176000 1160000 + >; }; cpu@1 { device_type = "cpu"; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 7669c16259a..fa532aaacc6 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -173,6 +173,8 @@ &usb_otg_hs { interface-type = <0>; usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; mode = <3>; power = <50>; }; diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts index a84684a9589..b9b55c95a56 100644 --- a/arch/arm/boot/dts/omap3-gta04.dts +++ b/arch/arm/boot/dts/omap3-gta04.dts @@ -131,6 +131,8 @@ &usb_otg_hs { interface-type = <0>; usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; mode = <3>; power = <50>; }; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index d64fa04e83f..c4f20bfe4cc 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -26,9 +26,116 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; + gpio_keys { + compatible = "gpio-keys"; + + camera_lens_cover { + label = "Camera Lens Cover"; + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */ + gpio-key,wakeup; + }; + + camera_focus { + label = "Camera Focus"; + gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */ + linux,code = <0x210>; /* KEY_CAMERA_FOCUS */ + gpio-key,wakeup; + }; + + camera_capture { + label = "Camera Capture"; + gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */ + linux,code = <0xd4>; /* KEY_CAMERA */ + gpio-key,wakeup; + }; + + lock_button { + label = "Lock Button"; + gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */ + linux,code = <0x98>; /* KEY_SCREENLOCK */ + gpio-key,wakeup; + }; + + keypad_slide { + label = "Keypad Slide"; + gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */ + gpio-key,wakeup; + }; + + proximity_sensor { + label = "Proximity Sensor"; + gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */ + }; + }; + +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */ + 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x18a (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x18e (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + 0x190 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */ + 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */ + 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ + 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ + 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ + >; + }; + + display_pins: pinmux_display_pins { + pinctrl-single,pins = < + 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ + >; + }; }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <2200000>; twl: twl@48 { @@ -39,6 +146,98 @@ }; #include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&vaux1 { + regulator-name = "V28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; /* due battery cover sensor */ +}; + +&vaux2 { + regulator-name = "VCSI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&vaux3 { + regulator-name = "VMMC2_30"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-name = "VCAM_ANA_28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +&vmmc1 { + regulator-name = "VMMC1"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; +}; + +&vmmc2 { + regulator-name = "V28_A"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; /* due VIO leak to AIC34 VDDs */ +}; + +&vpll1 { + regulator-name = "VPLL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&vpll2 { + regulator-name = "VSDI_CSI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&vsim { + regulator-name = "VMMC2_IO_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&vio { + regulator-name = "VIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + +}; + +&vintana1 { + regulator-name = "VINTANA1"; + /* fixed to 1500000 */ + regulator-always-on; +}; + +&vintana2 { + regulator-name = "VINTANA2"; + regulator-min-microvolt = <2750000>; + regulator-max-microvolt = <2750000>; + regulator-always-on; +}; + +&vintdig { + regulator-name = "VINTDIG"; + /* fixed to 1500000 */ + regulator-always-on; +}; + +&twl { + twl_audio: audio { + compatible = "ti,twl4030-audio"; + ti,enable-vibra = <1>; + }; +}; &twl_gpio { ti,pullups = <0x0>; @@ -46,15 +245,117 @@ }; &i2c2 { - clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; + + tlv320aic3x: tlv320aic3x@18 { + compatible = "ti,tlv320aic3x"; + reg = <0x18>; + gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */ + ai3x-gpio-func = < + 0 /* AIC3X_GPIO1_FUNC_DISABLED */ + 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */ + >; + + AVDD-supply = <&vmmc2>; + DRVDD-supply = <&vmmc2>; + IOVDD-supply = <&vio>; + DVDD-supply = <&vio>; + }; + + tlv320aic3x_aux: tlv320aic3x@19 { + compatible = "ti,tlv320aic3x"; + reg = <0x19>; + gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */ + + AVDD-supply = <&vmmc2>; + DRVDD-supply = <&vmmc2>; + IOVDD-supply = <&vio>; + DVDD-supply = <&vio>; + }; + + lp5523: lp5523@32 { + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ + enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */ + + chan0 { + chan-name = "lp5523:kb1"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan1 { + chan-name = "lp5523:kb2"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan2 { + chan-name = "lp5523:kb3"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan3 { + chan-name = "lp5523:kb4"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan4 { + chan-name = "lp5523:b"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan5 { + chan-name = "lp5523:g"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan6 { + chan-name = "lp5523:r"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan7 { + chan-name = "lp5523:kb5"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan8 { + chan-name = "lp5523:kb6"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + }; + + bq27200: bq27200@55 { + compatible = "ti,bq27200"; + reg = <0x55>; + }; }; &i2c3 { - clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + + clock-frequency = <400000>; }; &mmc1 { - status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */ }; &mmc2 { @@ -65,6 +366,78 @@ status = "disabled"; }; +&gpmc { + ranges = <0 0 0x04000000 0x10000000>; /* 256MB */ + + /* gpio-irq for dma: 65 */ + + onenand@0,0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0 0 0x10000000>; + + gpmc,sync-read; + gpmc,sync-write; + gpmc,burst-length = <16>; + gpmc,burst-read; + gpmc,burst-wrap; + gpmc,burst-write; + gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */ + gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */ + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <87>; + gpmc,cs-wr-off-ns = <87>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <15>; + gpmc,oe-off-ns = <87>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <87>; + gpmc,rd-cycle-ns = <112>; + gpmc,wr-cycle-ns = <112>; + gpmc,access-ns = <81>; + gpmc,page-burst-access-ns = <15>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,clk-activation-ns = <5>; + gpmc,wr-data-mux-bus-ns = <30>; + gpmc,wr-access-ns = <81>; + gpmc,sync-clk-ps = <15000>; + + /* + * MTD partition table corresponding to Nokia's + * Maemo 5 (Fremantle) release. + */ + partition@0 { + label = "bootloader"; + reg = <0x00000000 0x00020000>; + read-only; + }; + partition@1 { + label = "config"; + reg = <0x00020000 0x00060000>; + }; + partition@2 { + label = "log"; + reg = <0x00080000 0x00040000>; + }; + partition@3 { + label = "kernel"; + reg = <0x000c0000 0x00200000>; + }; + partition@4 { + label = "initfs"; + reg = <0x002c0000 0x00200000>; + }; + partition@5 { + label = "rootfs"; + reg = <0x004c0000 0x0fb40000>; + }; + }; +}; + &mcspi1 { /* * For some reason, touchscreen is necessary for screen to work at @@ -81,12 +454,31 @@ compatible = "acx565akm"; spi-max-frequency = <6000000>; reg = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&display_pins>; }; }; &usb_otg_hs { interface-type = <0>; usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; mode = <2>; power = <50>; }; + +&uart1 { + status = "disabled"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index f275beea67b..f3a0c26ed0c 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -19,6 +19,9 @@ interrupt-parent = <&intc>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -37,6 +40,7 @@ pmu { compatible = "arm,cortex-a8-pmu"; + reg = <0x54000000 0x800000>; interrupts = <3>; ti,hwmods = "debugss"; }; @@ -71,6 +75,8 @@ */ ocp { compatible = "simple-bus"; + reg = <0x68000000 0x10000>; + interrupts = <9 10>; #address-cells = <1>; #size-cells = <1>; ranges; @@ -193,24 +199,40 @@ uart1: serial@4806a000 { compatible = "ti,omap3-uart"; + reg = <0x4806a000 0x2000>; + interrupts = <72>; + dmas = <&sdma 49 &sdma 50>; + dma-names = "tx", "rx"; ti,hwmods = "uart1"; clock-frequency = <48000000>; }; uart2: serial@4806c000 { compatible = "ti,omap3-uart"; + reg = <0x4806c000 0x400>; + interrupts = <73>; + dmas = <&sdma 51 &sdma 52>; + dma-names = "tx", "rx"; ti,hwmods = "uart2"; clock-frequency = <48000000>; }; uart3: serial@49020000 { compatible = "ti,omap3-uart"; + reg = <0x49020000 0x400>; + interrupts = <74>; + dmas = <&sdma 53 &sdma 54>; + dma-names = "tx", "rx"; ti,hwmods = "uart3"; clock-frequency = <48000000>; }; i2c1: i2c@48070000 { compatible = "ti,omap3-i2c"; + reg = <0x48070000 0x80>; + interrupts = <56>; + dmas = <&sdma 27 &sdma 28>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c1"; @@ -218,6 +240,10 @@ i2c2: i2c@48072000 { compatible = "ti,omap3-i2c"; + reg = <0x48072000 0x80>; + interrupts = <57>; + dmas = <&sdma 29 &sdma 30>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c2"; @@ -225,6 +251,10 @@ i2c3: i2c@48060000 { compatible = "ti,omap3-i2c"; + reg = <0x48060000 0x80>; + interrupts = <61>; + dmas = <&sdma 25 &sdma 26>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c3"; @@ -232,6 +262,8 @@ mcspi1: spi@48098000 { compatible = "ti,omap2-mcspi"; + reg = <0x48098000 0x100>; + interrupts = <65>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi1"; @@ -250,6 +282,8 @@ mcspi2: spi@4809a000 { compatible = "ti,omap2-mcspi"; + reg = <0x4809a000 0x100>; + interrupts = <66>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi2"; @@ -263,6 +297,8 @@ mcspi3: spi@480b8000 { compatible = "ti,omap2-mcspi"; + reg = <0x480b8000 0x100>; + interrupts = <91>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi3"; @@ -276,6 +312,8 @@ mcspi4: spi@480ba000 { compatible = "ti,omap2-mcspi"; + reg = <0x480ba000 0x100>; + interrupts = <48>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi4"; @@ -284,8 +322,17 @@ dma-names = "tx0", "rx0"; }; + hdqw1w: 1w@480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; + mmc1: mmc@4809c000 { compatible = "ti,omap3-hsmmc"; + reg = <0x4809c000 0x200>; + interrupts = <83>; ti,hwmods = "mmc1"; ti,dual-volt; dmas = <&sdma 61>, <&sdma 62>; @@ -294,6 +341,8 @@ mmc2: mmc@480b4000 { compatible = "ti,omap3-hsmmc"; + reg = <0x480b4000 0x200>; + interrupts = <86>; ti,hwmods = "mmc2"; dmas = <&sdma 47>, <&sdma 48>; dma-names = "tx", "rx"; @@ -301,6 +350,8 @@ mmc3: mmc@480ad000 { compatible = "ti,omap3-hsmmc"; + reg = <0x480ad000 0x200>; + interrupts = <94>; ti,hwmods = "mmc3"; dmas = <&sdma 77>, <&sdma 78>; dma-names = "tx", "rx"; @@ -308,6 +359,7 @@ wdt2: wdt@48314000 { compatible = "ti,omap3-wdt"; + reg = <0x48314000 0x80>; ti,hwmods = "wd_timer2"; }; diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index f8b3765eb9b..380c22eb468 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -31,6 +31,10 @@ ocp { uart4: serial@49042000 { compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + dmas = <&sdma 81 &sdma 82>; + dma-names = "tx", "rx"; ti,hwmods = "uart4"; clock-frequency = <48000000>; }; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 56c435468e9..816d1c95b59 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -62,3 +62,7 @@ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; }; }; + +&gpio1 { + ti,no-reset-on-init; +}; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 17a3618b190..e8d97b46690 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -17,6 +17,10 @@ interrupt-parent = <&gic>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -218,6 +222,7 @@ gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; + ti,no-idle-on-init; }; uart1: serial@4806a000 { @@ -496,6 +501,7 @@ reg = <0x4c000000 0x100>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "emif1"; + ti,no-idle-on-init; phy-type = <1>; hw-caps-read-idle-ctrl; hw-caps-ll-interface; @@ -507,6 +513,7 @@ reg = <0x4d000000 0x100>; interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "emif2"; + ti,no-idle-on-init; phy-type = <1>; hw-caps-read-idle-ctrl; hw-caps-ll-interface; diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index d784b3a0041..002fa70180a 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -62,7 +62,6 @@ pinctrl-0 = < &twl6040_pins &mcpdm_pins - &dmic_pins &mcbsp1_pins &mcbsp2_pins &usbhost_pins @@ -71,7 +70,7 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */ + 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ >; }; @@ -85,15 +84,6 @@ >; }; - dmic_pins: pinmux_dmic_pins { - pinctrl-single,pins = < - 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */ - 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */ - 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */ - 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */ - >; - }; - mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ @@ -131,25 +121,25 @@ 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ - 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ >; }; mcspi3_pins: pinmux_mcspi3_pins { pinctrl-single,pins = < - 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ - 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ - 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ - 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ >; }; mcspi4_pins: pinmux_mcspi4_pins { pinctrl-single,pins = < - 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ - 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ - 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ - 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ + 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */ + 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */ + 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */ + 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */ >; }; @@ -334,8 +324,6 @@ regulator-name = "smps10_out1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; }; ldo1_reg: ldo1 { @@ -503,3 +491,7 @@ pinctrl-names = "default"; pinctrl-0 = <&uart5_pins>; }; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 6192c458bea..154d92fae1d 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -21,6 +21,11 @@ interrupt-parent = <&gic>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + i2c4 = &i2c5; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -33,10 +38,17 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a15"; reg = <0x0>; + + operating-points = < + /* kHz uV */ + 500000 880000 + 1000000 1060000 + 1500000 1250000 + >; }; cpu@1 { device_type = "cpu"; @@ -52,7 +64,6 @@ <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>; - clock-frequency = <6144000>; }; gic: interrupt-controller@48211000 { @@ -607,6 +618,7 @@ emif1: emif@4c000000 { compatible = "ti,emif-4d5"; ti,hwmods = "emif1"; + ti,no-idle-on-init; phy-type = <2>; /* DDR PHY type: Intelli PHY */ reg = <0x4c000000 0x400>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; @@ -618,6 +630,7 @@ emif2: emif@4d000000 { compatible = "ti,emif-4d5"; ti,hwmods = "emif2"; + ti,no-idle-on-init; phy-type = <2>; /* DDR PHY type: Intelli PHY */ reg = <0x4d000000 0x400>; interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; @@ -648,6 +661,7 @@ reg = <0x4a030000 0x10000>; interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; usb-phy = <&usb2_phy>, <&usb3_phy>; + dr_mode = "peripheral"; tx-fifo-resize; }; }; diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index ae6a17aed9e..af7fa40fd21 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -23,6 +23,22 @@ compatible = "ti,twl4030-wdt"; }; + vaux1: regulator-vaux1 { + compatible = "ti,twl4030-vaux1"; + }; + + vaux2: regulator-vaux2 { + compatible = "ti,twl4030-vaux2"; + }; + + vaux3: regulator-vaux3 { + compatible = "ti,twl4030-vaux3"; + }; + + vaux4: regulator-vaux4 { + compatible = "ti,twl4030-vaux4"; + }; + vcc: regulator-vdd1 { compatible = "ti,twl4030-vdd1"; regulator-min-microvolt = <600000>; @@ -35,10 +51,20 @@ regulator-max-microvolt = <1800000>; }; - vpll2: regulator-vpll2 { - compatible = "ti,twl4030-vpll2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; + vio: regulator-vio { + compatible = "ti,twl4030-vio"; + }; + + vintana1: regulator-vintana1 { + compatible = "ti,twl4030-vintana1"; + }; + + vintana2: regulator-vintana2 { + compatible = "ti,twl4030-vintana2"; + }; + + vintdig: regulator-vintdig { + compatible = "ti,twl4030-vintdig"; }; vmmc1: regulator-vmmc1 { @@ -65,6 +91,16 @@ compatible = "ti,twl4030-vusb3v1"; }; + vpll1: regulator-vpll1 { + compatible = "ti,twl4030-vpll1"; + }; + + vpll2: regulator-vpll2 { + compatible = "ti,twl4030-vpll2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vsim: regulator-vsim { compatible = "ti,twl4030-vsim"; regulator-min-microvolt = <1800000>; @@ -97,4 +133,9 @@ compatible = "ti,twl4030-pwmled"; #pwm-cells = <2>; }; + + twl_pwrbutton: pwrbutton { + compatible = "ti,twl4030-pwrbutton"; + interrupts = <8>; + }; }; diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h new file mode 100644 index 00000000000..eb6c366adfb --- /dev/null +++ b/include/dt-bindings/pinctrl/am43xx.h @@ -0,0 +1,31 @@ +/* + * This header provides constants specific to AM43XX pinctrl bindings. + */ + +#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H +#define _DT_BINDINGS_PINCTRL_AM43XX_H + +#define MUX_MODE0 0 +#define MUX_MODE1 1 +#define MUX_MODE2 2 +#define MUX_MODE3 3 +#define MUX_MODE4 4 +#define MUX_MODE5 5 +#define MUX_MODE6 6 +#define MUX_MODE7 7 + +#define PULL_DISABLE (1 << 16) +#define PULL_UP (1 << 17) +#define INPUT_EN (1 << 18) +#define SLEWCTRL_FAST (1 << 19) +#define DS0_PULL_UP_DOWN_EN (1 << 27) + +#define PIN_OUTPUT (PULL_DISABLE) +#define PIN_OUTPUT_PULLUP (PULL_UP) +#define PIN_OUTPUT_PULLDOWN 0 +#define PIN_INPUT (INPUT_EN | PULL_DISABLE) +#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP) +#define PIN_INPUT_PULLDOWN (INPUT_EN) + +#endif + |