Merge remote branch 'origin' into secretlab/next-devicetree

Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.

Conflicts:
	drivers/i2c/busses/i2c-cpm.c
	drivers/i2c/busses/i2c-mpc.c
	drivers/net/gianfar.c

Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

44 files changed, 2475 insertions, 372 deletions

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 8d3df0397de..f865be2276d 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -207,6 +207,21 @@ config USB_OHCI_HCD
 	  To compile this driver as a module, choose M here: the
 	  module will be called ohci-hcd.
 
+config USB_OHCI_HCD_OMAP1
+	bool "OHCI support for OMAP1/2 chips"
+	depends on USB_OHCI_HCD && (ARCH_OMAP1 || ARCH_OMAP2)
+	default y
+	---help---
+	  Enables support for the OHCI controller on OMAP1/2 chips.
+
+config USB_OHCI_HCD_OMAP3
+	bool "OHCI support for OMAP3 and later chips"
+	depends on USB_OHCI_HCD && (ARCH_OMAP3 || ARCH_OMAP4)
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  OMAP3 and later chips.
+
 config USB_OHCI_HCD_PPC_SOC
 	bool "OHCI support for on-chip PPC USB controller"
 	depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
diff --git a/drivers/usb/host/ehci-au1xxx.c b/drivers/usb/host/ehci-au1xxx.c
index e3a74e75e82..faa61748db7 100644
--- a/drivers/usb/host/ehci-au1xxx.c
+++ b/drivers/usb/host/ehci-au1xxx.c
@@ -69,6 +69,15 @@ static void au1xxx_stop_ehc(void)
 	au_sync();
 }
 
+static int au1xxx_ehci_setup(struct usb_hcd *hcd)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int ret = ehci_init(hcd);
+
+	ehci->need_io_watchdog = 0;
+	return ret;
+}
+
 static const struct hc_driver ehci_au1xxx_hc_driver = {
 	.description		= hcd_name,
 	.product_desc		= "Au1xxx EHCI",
@@ -86,7 +95,7 @@ static const struct hc_driver ehci_au1xxx_hc_driver = {
 	 * FIXME -- ehci_init() doesn't do enough here.
 	 * See ehci-ppc-soc for a complete implementation.
 	 */
-	.reset			= ehci_init,
+	.reset			= au1xxx_ehci_setup,
 	.start			= ehci_run,
 	.stop			= ehci_stop,
 	.shutdown		= ehci_shutdown,
@@ -215,26 +224,17 @@ static int ehci_hcd_au1xxx_drv_suspend(struct device *dev)
 		msleep(10);
 
 	/* Root hub was already suspended. Disable irq emission and
-	 * mark HW unaccessible, bail out if RH has been resumed. Use
-	 * the spinlock to properly synchronize with possible pending
-	 * RH suspend or resume activity.
-	 *
-	 * This is still racy as hcd->state is manipulated outside of
-	 * any locks =P But that will be a different fix.
+	 * mark HW unaccessible.  The PM and USB cores make sure that
+	 * the root hub is either suspended or stopped.
 	 */
 	spin_lock_irqsave(&ehci->lock, flags);
-	if (hcd->state != HC_STATE_SUSPENDED) {
-		rc = -EINVAL;
-		goto bail;
-	}
+	ehci_prepare_ports_for_controller_suspend(ehci);
 	ehci_writel(ehci, 0, &ehci->regs->intr_enable);
 	(void)ehci_readl(ehci, &ehci->regs->intr_enable);
 
 	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
 
 	au1xxx_stop_ehc();
-
-bail:
 	spin_unlock_irqrestore(&ehci->lock, flags);
 
 	// could save FLADJ in case of Vaux power loss
@@ -264,6 +264,7 @@ static int ehci_hcd_au1xxx_drv_resume(struct device *dev)
 	if (ehci_readl(ehci, &ehci->regs->configured_flag) == FLAG_CF) {
 		int	mask = INTR_MASK;
 
+		ehci_prepare_ports_for_controller_resume(ehci);
 		if (!hcd->self.root_hub->do_remote_wakeup)
 			mask &= ~STS_PCD;
 		ehci_writel(ehci, mask, &ehci->regs->intr_enable);
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 0e26aa13f15..5cd967d2893 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -313,6 +313,7 @@ static int ehci_fsl_drv_suspend(struct device *dev)
 	struct ehci_fsl *ehci_fsl = hcd_to_ehci_fsl(hcd);
 	void __iomem *non_ehci = hcd->regs;
 
+	ehci_prepare_ports_for_controller_suspend(hcd_to_ehci(hcd));
 	if (!fsl_deep_sleep())
 		return 0;
 
@@ -327,6 +328,7 @@ static int ehci_fsl_drv_resume(struct device *dev)
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 	void __iomem *non_ehci = hcd->regs;
 
+	ehci_prepare_ports_for_controller_resume(ehci);
 	if (!fsl_deep_sleep())
 		return 0;
 
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index 207e7a85aeb..ef3e88f0b3c 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -31,13 +31,12 @@
 #include <linux/list.h>
 #include <linux/interrupt.h>
 #include <linux/usb.h>
+#include <linux/usb/hcd.h>
 #include <linux/moduleparam.h>
 #include <linux/dma-mapping.h>
 #include <linux/debugfs.h>
 #include <linux/slab.h>
 
-#include "../core/hcd.h"
-
 #include <asm/byteorder.h>
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -543,6 +542,7 @@ static int ehci_init(struct usb_hcd *hcd)
 	 */
 	ehci->periodic_size = DEFAULT_I_TDPS;
 	INIT_LIST_HEAD(&ehci->cached_itd_list);
+	INIT_LIST_HEAD(&ehci->cached_sitd_list);
 	if ((retval = ehci_mem_init(ehci, GFP_KERNEL)) < 0)
 		return retval;
 
diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index 19372673bf0..e7d3d8def28 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -106,12 +106,75 @@ static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
 	ehci->owned_ports = 0;
 }
 
+static void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
+		bool suspending)
+{
+	int		port;
+	u32		temp;
+
+	/* If remote wakeup is enabled for the root hub but disabled
+	 * for the controller, we must adjust all the port wakeup flags
+	 * when the controller is suspended or resumed.  In all other
+	 * cases they don't need to be changed.
+	 */
+	if (!ehci_to_hcd(ehci)->self.root_hub->do_remote_wakeup ||
+			device_may_wakeup(ehci_to_hcd(ehci)->self.controller))
+		return;
+
+	/* clear phy low-power mode before changing wakeup flags */
+	if (ehci->has_hostpc) {
+		port = HCS_N_PORTS(ehci->hcs_params);
+		while (port--) {
+			u32 __iomem	*hostpc_reg;
+
+			hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+					+ HOSTPC0 + 4 * port);
+			temp = ehci_readl(ehci, hostpc_reg);
+			ehci_writel(ehci, temp & ~HOSTPC_PHCD, hostpc_reg);
+		}
+		msleep(5);
+	}
+
+	port = HCS_N_PORTS(ehci->hcs_params);
+	while (port--) {
+		u32 __iomem	*reg = &ehci->regs->port_status[port];
+		u32		t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
+		u32		t2 = t1 & ~PORT_WAKE_BITS;
+
+		/* If we are suspending the controller, clear the flags.
+		 * If we are resuming the controller, set the wakeup flags.
+		 */
+		if (!suspending) {
+			if (t1 & PORT_CONNECT)
+				t2 |= PORT_WKOC_E | PORT_WKDISC_E;
+			else
+				t2 |= PORT_WKOC_E | PORT_WKCONN_E;
+		}
+		ehci_vdbg(ehci, "port %d, %08x -> %08x\n",
+				port + 1, t1, t2);
+		ehci_writel(ehci, t2, reg);
+	}
+
+	/* enter phy low-power mode again */
+	if (ehci->has_hostpc) {
+		port = HCS_N_PORTS(ehci->hcs_params);
+		while (port--) {
+			u32 __iomem	*hostpc_reg;
+
+			hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+					+ HOSTPC0 + 4 * port);
+			temp = ehci_readl(ehci, hostpc_reg);
+			ehci_writel(ehci, temp | HOSTPC_PHCD, hostpc_reg);
+		}
+	}
+}
+
 static int ehci_bus_suspend (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	int			port;
 	int			mask;
-	u32 __iomem		*hostpc_reg = NULL;
+	int			changed;
 
 	ehci_dbg(ehci, "suspend root hub\n");
 
@@ -155,15 +218,13 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	 */
 	ehci->bus_suspended = 0;
 	ehci->owned_ports = 0;
+	changed = 0;
 	port = HCS_N_PORTS(ehci->hcs_params);
 	while (port--) {
 		u32 __iomem	*reg = &ehci->regs->port_status [port];
 		u32		t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
-		u32		t2 = t1;
+		u32		t2 = t1 & ~PORT_WAKE_BITS;
 
-		if (ehci->has_hostpc)
-			hostpc_reg = (u32 __iomem *)((u8 *)ehci->regs
-				+ HOSTPC0 + 4 * (port & 0xff));
 		/* keep track of which ports we suspend */
 		if (t1 & PORT_OWNER)
 			set_bit(port, &ehci->owned_ports);
@@ -172,40 +233,45 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 			set_bit(port, &ehci->bus_suspended);
 		}
 
-		/* enable remote wakeup on all ports */
+		/* enable remote wakeup on all ports, if told to do so */
 		if (hcd->self.root_hub->do_remote_wakeup) {
 			/* only enable appropriate wake bits, otherwise the
 			 * hardware can not go phy low power mode. If a race
 			 * condition happens here(connection change during bits
 			 * set), the port change detection will finally fix it.
 			 */
-			if (t1 & PORT_CONNECT) {
+			if (t1 & PORT_CONNECT)
 				t2 |= PORT_WKOC_E | PORT_WKDISC_E;
-				t2 &= ~PORT_WKCONN_E;
-			} else {
+			else
 				t2 |= PORT_WKOC_E | PORT_WKCONN_E;
-				t2 &= ~PORT_WKDISC_E;
-			}
-		} else
-			t2 &= ~PORT_WAKE_BITS;
+		}
 
 		if (t1 != t2) {
 			ehci_vdbg (ehci, "port %d, %08x -> %08x\n",
 				port + 1, t1, t2);
 			ehci_writel(ehci, t2, reg);
-			if (hostpc_reg) {
-				u32	t3;
+			changed = 1;
+		}
+	}
 
-				spin_unlock_irq(&ehci->lock);
-				msleep(5);/* 5ms for HCD enter low pwr mode */
-				spin_lock_irq(&ehci->lock);
-				t3 = ehci_readl(ehci, hostpc_reg);
-				ehci_writel(ehci, t3 | HOSTPC_PHCD, hostpc_reg);
-				t3 = ehci_readl(ehci, hostpc_reg);
-				ehci_dbg(ehci, "Port%d phy low pwr mode %s\n",
+	if (changed && ehci->has_hostpc) {
+		spin_unlock_irq(&ehci->lock);
+		msleep(5);	/* 5 ms for HCD to enter low-power mode */
+		spin_lock_irq(&ehci->lock);
+
+		port = HCS_N_PORTS(ehci->hcs_params);
+		while (port--) {
+			u32 __iomem	*hostpc_reg;
+			u32		t3;
+
+			hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+					+ HOSTPC0 + 4 * port);
+			t3 = ehci_readl(ehci, hostpc_reg);
+			ehci_writel(ehci, t3 | HOSTPC_PHCD, hostpc_reg);
+			t3 = ehci_readl(ehci, hostpc_reg);
+			ehci_dbg(ehci, "Port %d phy low-power mode %s\n",
 					port, (t3 & HOSTPC_PHCD) ?
 					"succeeded" : "failed");
-			}
 		}
 	}
 
@@ -291,6 +357,25 @@ static int ehci_bus_resume (struct usb_hcd *hcd)
 	msleep(8);
 	spin_lock_irq(&ehci->lock);
 
+	/* clear phy low-power mode before resume */
+	if (ehci->bus_suspended && ehci->has_hostpc) {
+		i = HCS_N_PORTS(ehci->hcs_params);
+		while (i--) {
+			if (test_bit(i, &ehci->bus_suspended)) {
+				u32 __iomem	*hostpc_reg;
+
+				hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+						+ HOSTPC0 + 4 * i);
+				temp = ehci_readl(ehci, hostpc_reg);
+				ehci_writel(ehci, temp & ~HOSTPC_PHCD,
+						hostpc_reg);
+			}
+		}
+		spin_unlock_irq(&ehci->lock);
+		msleep(5);
+		spin_lock_irq(&ehci->lock);
+	}
+
 	/* manually resume the ports we suspended during bus_suspend() */
 	i = HCS_N_PORTS (ehci->hcs_params);
 	while (i--) {
@@ -659,7 +744,7 @@ static int ehci_hub_control (
 		 * Even if OWNER is set, so the port is owned by the
 		 * companion controller, khubd needs to be able to clear
 		 * the port-change status bits (especially
-		 * USB_PORT_FEAT_C_CONNECTION).
+		 * USB_PORT_STAT_C_CONNECTION).
 		 */
 
 		switch (wValue) {
@@ -675,16 +760,25 @@ static int ehci_hub_control (
 				goto error;
 			if (ehci->no_selective_suspend)
 				break;
-			if (temp & PORT_SUSPEND) {
-				if ((temp & PORT_PE) == 0)
-					goto error;
-				/* resume signaling for 20 msec */
-				temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
-				ehci_writel(ehci, temp | PORT_RESUME,
-						status_reg);
-				ehci->reset_done [wIndex] = jiffies
-						+ msecs_to_jiffies (20);
+			if (!(temp & PORT_SUSPEND))
+				break;
+			if ((temp & PORT_PE) == 0)
+				goto error;
+
+			/* clear phy low-power mode before resume */
+			if (hostpc_reg) {
+				temp1 = ehci_readl(ehci, hostpc_reg);
+				ehci_writel(ehci, temp1 & ~HOSTPC_PHCD,
+						hostpc_reg);
+				spin_unlock_irqrestore(&ehci->lock, flags);
+				msleep(5);/* wait to leave low-power mode */
+				spin_lock_irqsave(&ehci->lock, flags);
 			}
+			/* resume signaling for 20 msec */
+			temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
+			ehci_writel(ehci, temp | PORT_RESUME, status_reg);
+			ehci->reset_done[wIndex] = jiffies
+					+ msecs_to_jiffies(20);
 			break;
 		case USB_PORT_FEAT_C_SUSPEND:
 			clear_bit(wIndex, &ehci->port_c_suspend);
@@ -729,12 +823,12 @@ static int ehci_hub_control (
 
 		// wPortChange bits
 		if (temp & PORT_CSC)
-			status |= 1 << USB_PORT_FEAT_C_CONNECTION;
+			status |= USB_PORT_STAT_C_CONNECTION << 16;
 		if (temp & PORT_PEC)
-			status |= 1 << USB_PORT_FEAT_C_ENABLE;
+			status |= USB_PORT_STAT_C_ENABLE << 16;
 
 		if ((temp & PORT_OCC) && !ignore_oc){
-			status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT;
+			status |= USB_PORT_STAT_C_OVERCURRENT << 16;
 
 			/*
 			 * Hubs should disable port power on over-current.
@@ -791,7 +885,7 @@ static int ehci_hub_control (
 		if ((temp & PORT_RESET)
 				&& time_after_eq(jiffies,
 					ehci->reset_done[wIndex])) {
-			status |= 1 << USB_PORT_FEAT_C_RESET;
+			status |= USB_PORT_STAT_C_RESET << 16;
 			ehci->reset_done [wIndex] = 0;
 
 			/* force reset to complete */
@@ -801,7 +895,7 @@ static int ehci_hub_control (
 			 * this bit; seems too long to spin routinely...
 			 */
 			retval = handshake(ehci, status_reg,
-					PORT_RESET, 0, 750);
+					PORT_RESET, 0, 1000);
 			if (retval != 0) {
 				ehci_err (ehci, "port %d reset error %d\n",
 					wIndex + 1, retval);
@@ -833,7 +927,7 @@ static int ehci_hub_control (
 		 */
 
 		if (temp & PORT_CONNECT) {
-			status |= 1 << USB_PORT_FEAT_CONNECTION;
+			status |= USB_PORT_STAT_CONNECTION;
 			// status may be from integrated TT
 			if (ehci->has_hostpc) {
 				temp1 = ehci_readl(ehci, hostpc_reg);
@@ -842,11 +936,11 @@ static int ehci_hub_control (
 				status |= ehci_port_speed(ehci, temp);
 		}
 		if (temp & PORT_PE)
-			status |= 1 << USB_PORT_FEAT_ENABLE;
+			status |= USB_PORT_STAT_ENABLE;
 
 		/* maybe the port was unsuspended without our knowledge */
 		if (temp & (PORT_SUSPEND|PORT_RESUME)) {
-			status |= 1 << USB_PORT_FEAT_SUSPEND;
+			status |= USB_PORT_STAT_SUSPEND;
 		} else if (test_bit(wIndex, &ehci->suspended_ports)) {
 			clear_bit(wIndex, &ehci->suspended_ports);
 			ehci->reset_done[wIndex] = 0;
@@ -855,13 +949,13 @@ static int ehci_hub_control (
 		}
 
 		if (temp & PORT_OC)
-			status |= 1 << USB_PORT_FEAT_OVER_CURRENT;
+			status |= USB_PORT_STAT_OVERCURRENT;
 		if (temp & PORT_RESET)
-			status |= 1 << USB_PORT_FEAT_RESET;
+			status |= USB_PORT_STAT_RESET;
 		if (temp & PORT_POWER)
-			status |= 1 << USB_PORT_FEAT_POWER;
+			status |= USB_PORT_STAT_POWER;
 		if (test_bit(wIndex, &ehci->port_c_suspend))
-			status |= 1 << USB_PORT_FEAT_C_SUSPEND;
+			status |= USB_PORT_STAT_C_SUSPEND << 16;
 
 #ifndef	VERBOSE_DEBUG
 	if (status & ~0xffff)	/* only if wPortChange is interesting */
diff --git a/drivers/usb/host/ehci-mem.c b/drivers/usb/host/ehci-mem.c
index aeda96e0af6..1f3f01eacaf 100644
--- a/drivers/usb/host/ehci-mem.c
+++ b/drivers/usb/host/ehci-mem.c
@@ -136,7 +136,7 @@ static inline void qh_put (struct ehci_qh *qh)
 
 static void ehci_mem_cleanup (struct ehci_hcd *ehci)
 {
-	free_cached_itd_list(ehci);
+	free_cached_lists(ehci);
 	if (ehci->async)
 		qh_put (ehci->async);
 	ehci->async = NULL;
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index a67a0030dd5..5450e628157 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -116,6 +116,8 @@
 #define	OMAP_UHH_DEBUG_CSR				(0x44)
 
 /* EHCI Register Set */
+#define EHCI_INSNREG04					(0xA0)
+#define EHCI_INSNREG04_DISABLE_UNSUSPEND		(1 << 5)
 #define	EHCI_INSNREG05_ULPI				(0xA4)
 #define	EHCI_INSNREG05_ULPI_CONTROL_SHIFT		31
 #define	EHCI_INSNREG05_ULPI_PORTSEL_SHIFT		24
@@ -181,7 +183,7 @@ struct ehci_hcd_omap {
 	void __iomem		*ehci_base;
 
 	/* Regulators for USB PHYs.
-	 * Each PHY can have a seperate regulator.
+	 * Each PHY can have a separate regulator.
 	 */
 	struct regulator        *regulator[OMAP3_HS_USB_PORTS];
 };
@@ -352,8 +354,8 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 		reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
 
 	/* Bypass the TLL module for PHY mode operation */
-	 if (omap_rev() <= OMAP3430_REV_ES2_1) {
-		dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1 \n");
+	if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
+		dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
 		if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) ||
 			(omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) ||
 				(omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY))
@@ -382,6 +384,18 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 	dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
 
 
+	/*
+	 * An undocumented "feature" in the OMAP3 EHCI controller,
+	 * causes suspended ports to be taken out of suspend when
+	 * the USBCMD.Run/Stop bit is cleared (for example when
+	 * we do ehci_bus_suspend).
+	 * This breaks suspend-resume if the root-hub is allowed
+	 * to suspend. Writing 1 to this undocumented register bit
+	 * disables this feature and restores normal behavior.
+	 */
+	ehci_omap_writel(omap->ehci_base, EHCI_INSNREG04,
+				EHCI_INSNREG04_DISABLE_UNSUSPEND);
+
 	if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) ||
 		(omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) ||
 			(omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)) {
@@ -629,11 +643,13 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 		}
 		snprintf(supply, sizeof(supply), "hsusb%d", i);
 		omap->regulator[i] = regulator_get(omap->dev, supply);
-		if (IS_ERR(omap->regulator[i]))
+		if (IS_ERR(omap->regulator[i])) {
+			omap->regulator[i] = NULL;
 			dev_dbg(&pdev->dev,
 			"failed to get ehci port%d regulator\n", i);
-		else
+		} else {
 			regulator_enable(omap->regulator[i]);
+		}
 	}
 
 	ret = omap_start_ehc(omap, hcd);
@@ -657,6 +673,9 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 		goto err_add_hcd;
 	}
 
+	/* root ports should always stay powered */
+	ehci_port_power(omap->ehci, 1);
+
 	return 0;
 
 err_add_hcd:
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index ead5f4f2aa5..d43d176161a 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -109,6 +109,9 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		return retval;
 
 	switch (pdev->vendor) {
+	case PCI_VENDOR_ID_NEC:
+		ehci->need_io_watchdog = 0;
+		break;
 	case PCI_VENDOR_ID_INTEL:
 		ehci->need_io_watchdog = 0;
 		if (pdev->device == 0x27cc) {
@@ -284,23 +287,15 @@ static int ehci_pci_suspend(struct usb_hcd *hcd)
 		msleep(10);
 
 	/* Root hub was already suspended. Disable irq emission and
-	 * mark HW unaccessible, bail out if RH has been resumed. Use
-	 * the spinlock to properly synchronize with possible pending
-	 * RH suspend or resume activity.
-	 *
-	 * This is still racy as hcd->state is manipulated outside of
-	 * any locks =P But that will be a different fix.
+	 * mark HW unaccessible.  The PM and USB cores make sure that
+	 * the root hub is either suspended or stopped.
 	 */
 	spin_lock_irqsave (&ehci->lock, flags);
-	if (hcd->state != HC_STATE_SUSPENDED) {
-		rc = -EINVAL;
-		goto bail;
-	}
+	ehci_prepare_ports_for_controller_suspend(ehci);
 	ehci_writel(ehci, 0, &ehci->regs->intr_enable);
 	(void)ehci_readl(ehci, &ehci->regs->intr_enable);
 
 	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
- bail:
 	spin_unlock_irqrestore (&ehci->lock, flags);
 
 	// could save FLADJ in case of Vaux power loss
@@ -330,6 +325,7 @@ static int ehci_pci_resume(struct usb_hcd *hcd, bool hibernated)
 				!hibernated) {
 		int	mask = INTR_MASK;
 
+		ehci_prepare_ports_for_controller_resume(ehci);
 		if (!hcd->self.root_hub->do_remote_wakeup)
 			mask &= ~STS_PCD;
 		ehci_writel(ehci, mask, &ehci->regs->intr_enable);
diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c
index 89521775c56..11a79c4f4a9 100644
--- a/drivers/usb/host/ehci-q.c
+++ b/drivers/usb/host/ehci-q.c
@@ -663,7 +663,7 @@ qh_urb_transaction (
 	 */
 	i = urb->num_sgs;
 	if (len > 0 && i > 0) {
-		sg = urb->sg->sg;
+		sg = urb->sg;
 		buf = sg_dma_address(sg);
 
 		/* urb->transfer_buffer_length may be smaller than the
diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c
index a0aaaaff256..805ec633a65 100644
--- a/drivers/usb/host/ehci-sched.c
+++ b/drivers/usb/host/ehci-sched.c
@@ -510,7 +510,7 @@ static int disable_periodic (struct ehci_hcd *ehci)
 	ehci_writel(ehci, cmd, &ehci->regs->command);
 	/* posted write ... */
 
-	free_cached_itd_list(ehci);
+	free_cached_lists(ehci);
 
 	ehci->next_uframe = -1;
 	return 0;
@@ -2139,13 +2139,27 @@ sitd_complete (
 			(stream->bEndpointAddress & USB_DIR_IN) ? "in" : "out");
 	}
 	iso_stream_put (ehci, stream);
-	/* OK to recycle this SITD now that its completion callback ran. */
+
 done:
 	sitd->urb = NULL;
-	sitd->stream = NULL;
-	list_move(&sitd->sitd_list, &stream->free_list);
-	iso_stream_put(ehci, stream);
-
+	if (ehci->clock_frame != sitd->frame) {
+		/* OK to recycle this SITD now. */
+		sitd->stream = NULL;
+		list_move(&sitd->sitd_list, &stream->free_list);
+		iso_stream_put(ehci, stream);
+	} else {
+		/* HW might remember this SITD, so we can't recycle it yet.
+		 * Move it to a safe place until a new frame starts.
+		 */
+		list_move(&sitd->sitd_list, &ehci->cached_sitd_list);
+		if (stream->refcount == 2) {
+			/* If iso_stream_put() were called here, stream
+			 * would be freed.  Instead, just prevent reuse.
+			 */
+			stream->ep->hcpriv = NULL;
+			stream->ep = NULL;
+		}
+	}
 	return retval;
 }
 
@@ -2211,9 +2225,10 @@ done:
 
 /*-------------------------------------------------------------------------*/
 
-static void free_cached_itd_list(struct ehci_hcd *ehci)
+static void free_cached_lists(struct ehci_hcd *ehci)
 {
 	struct ehci_itd *itd, *n;
+	struct ehci_sitd *sitd, *sn;
 
 	list_for_each_entry_safe(itd, n, &ehci->cached_itd_list, itd_list) {
 		struct ehci_iso_stream	*stream = itd->stream;
@@ -2221,6 +2236,13 @@ static void free_cached_itd_list(struct ehci_hcd *ehci)
 		list_move(&itd->itd_list, &stream->free_list);
 		iso_stream_put(ehci, stream);
 	}
+
+	list_for_each_entry_safe(sitd, sn, &ehci->cached_sitd_list, sitd_list) {
+		struct ehci_iso_stream	*stream = sitd->stream;
+		sitd->stream = NULL;
+		list_move(&sitd->sitd_list, &stream->free_list);
+		iso_stream_put(ehci, stream);
+	}
 }
 
 /*-------------------------------------------------------------------------*/
@@ -2247,7 +2269,7 @@ scan_periodic (struct ehci_hcd *ehci)
 		clock_frame = -1;
 	}
 	if (ehci->clock_frame != clock_frame) {
-		free_cached_itd_list(ehci);
+		free_cached_lists(ehci);
 		ehci->clock_frame = clock_frame;
 	}
 	clock %= mod;
@@ -2414,7 +2436,7 @@ restart:
 			clock = now;
 			clock_frame = clock >> 3;
 			if (ehci->clock_frame != clock_frame) {
-				free_cached_itd_list(ehci);
+				free_cached_lists(ehci);
 				ehci->clock_frame = clock_frame;
 			}
 		} else {
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index b1dce96dd62..650a687f285 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -87,8 +87,9 @@ struct ehci_hcd {			/* one per controller */
 	int			next_uframe;	/* scan periodic, start here */
 	unsigned		periodic_sched;	/* periodic activity count */
 
-	/* list of itds completed while clock_frame was still active */
+	/* list of itds & sitds completed while clock_frame was still active */