[TG3]: add 5780 fiber support

Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 249 insertions, 7 deletions

diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index 04d8b18e291..ffc854c4ab0 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -1100,7 +1100,7 @@ static int tg3_set_power_state(struct tg3 *tp, int state)
 		tp->link_config.orig_autoneg = tp->link_config.autoneg;
 	}
 
-	if (!(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES)) {
+	if (!(tp->tg3_flags2 & TG3_FLG2_ANY_SERDES)) {
 		tp->link_config.speed = SPEED_10;
 		tp->link_config.duplex = DUPLEX_HALF;
 		tp->link_config.autoneg = AUTONEG_ENABLE;
@@ -1247,6 +1247,25 @@ static void tg3_setup_flow_control(struct tg3 *tp, u32 local_adv, u32 remote_adv
 	u32 old_tx_mode = tp->tx_mode;
 
 	if (tp->tg3_flags & TG3_FLAG_PAUSE_AUTONEG) {
+
+		/* Convert 1000BaseX flow control bits to 1000BaseT
+		 * bits before resolving flow control.
+		 */
+		if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) {
+			local_adv &= ~(ADVERTISE_PAUSE_CAP |
+				       ADVERTISE_PAUSE_ASYM);
+			remote_adv &= ~(LPA_PAUSE_CAP | LPA_PAUSE_ASYM);
+
+			if (local_adv & ADVERTISE_1000XPAUSE)
+				local_adv |= ADVERTISE_PAUSE_CAP;
+			if (local_adv & ADVERTISE_1000XPSE_ASYM)
+				local_adv |= ADVERTISE_PAUSE_ASYM;
+			if (remote_adv & LPA_1000XPAUSE)
+				remote_adv |= LPA_PAUSE_CAP;
+			if (remote_adv & LPA_1000XPAUSE_ASYM)
+				remote_adv |= LPA_PAUSE_ASYM;
+		}
+
 		if (local_adv & ADVERTISE_PAUSE_CAP) {
 			if (local_adv & ADVERTISE_PAUSE_ASYM) {
 				if (remote_adv & LPA_PAUSE_CAP)
@@ -2507,12 +2526,226 @@ static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
 	return 0;
 }
 
+static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
+{
+	int current_link_up, err = 0;
+	u32 bmsr, bmcr;
+	u16 current_speed;
+	u8 current_duplex;
+
+	tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
+	tw32_f(MAC_MODE, tp->mac_mode);
+	udelay(40);
+
+	tw32(MAC_EVENT, 0);
+
+	tw32_f(MAC_STATUS,
+	     (MAC_STATUS_SYNC_CHANGED |
+	      MAC_STATUS_CFG_CHANGED |
+	      MAC_STATUS_MI_COMPLETION |
+	      MAC_STATUS_LNKSTATE_CHANGED));
+	udelay(40);
+
+	if (force_reset)
+		tg3_phy_reset(tp);
+
+	current_link_up = 0;
+	current_speed = SPEED_INVALID;
+	current_duplex = DUPLEX_INVALID;
+
+	err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+	err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+
+	err |= tg3_readphy(tp, MII_BMCR, &bmcr);
+
+	if ((tp->link_config.autoneg == AUTONEG_ENABLE) && !force_reset &&
+	    (tp->tg3_flags2 & TG3_FLG2_PARALLEL_DETECT)) {
+		/* do nothing, just check for link up at the end */
+	} else if (tp->link_config.autoneg == AUTONEG_ENABLE) {
+		u32 adv, new_adv;
+
+		err |= tg3_readphy(tp, MII_ADVERTISE, &adv);
+		new_adv = adv & ~(ADVERTISE_1000XFULL | ADVERTISE_1000XHALF |
+				  ADVERTISE_1000XPAUSE |
+				  ADVERTISE_1000XPSE_ASYM |
+				  ADVERTISE_SLCT);
+
+		/* Always advertise symmetric PAUSE just like copper */
+		new_adv |= ADVERTISE_1000XPAUSE;
+
+		if (tp->link_config.advertising & ADVERTISED_1000baseT_Half)
+			new_adv |= ADVERTISE_1000XHALF;
+		if (tp->link_config.advertising & ADVERTISED_1000baseT_Full)
+			new_adv |= ADVERTISE_1000XFULL;
+
+		if ((new_adv != adv) || !(bmcr & BMCR_ANENABLE)) {
+			tg3_writephy(tp, MII_ADVERTISE, new_adv);
+			bmcr |= BMCR_ANENABLE | BMCR_ANRESTART;
+			tg3_writephy(tp, MII_BMCR, bmcr);
+
+			tw32_f(MAC_EVENT, MAC_EVENT_LNKSTATE_CHANGED);
+			tp->tg3_flags2 |= TG3_FLG2_PHY_JUST_INITTED;
+			tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+
+			return err;
+		}
+	} else {
+		u32 new_bmcr;
+
+		bmcr &= ~BMCR_SPEED1000;
+		new_bmcr = bmcr & ~(BMCR_ANENABLE | BMCR_FULLDPLX);
+
+		if (tp->link_config.duplex == DUPLEX_FULL)
+			new_bmcr |= BMCR_FULLDPLX;
+
+		if (new_bmcr != bmcr) {
+			/* BMCR_SPEED1000 is a reserved bit that needs
+			 * to be set on write.
+			 */
+			new_bmcr |= BMCR_SPEED1000;
+
+			/* Force a linkdown */
+			if (netif_carrier_ok(tp->dev)) {
+				u32 adv;
+
+				err |= tg3_readphy(tp, MII_ADVERTISE, &adv);
+				adv &= ~(ADVERTISE_1000XFULL |
+					 ADVERTISE_1000XHALF |
+					 ADVERTISE_SLCT);
+				tg3_writephy(tp, MII_ADVERTISE, adv);
+				tg3_writephy(tp, MII_BMCR, bmcr |
+							   BMCR_ANRESTART |
+							   BMCR_ANENABLE);
+				udelay(10);
+				netif_carrier_off(tp->dev);
+			}
+			tg3_writephy(tp, MII_BMCR, new_bmcr);
+			bmcr = new_bmcr;
+			err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+			err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+			tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+		}
+	}
+
+	if (bmsr & BMSR_LSTATUS) {
+		current_speed = SPEED_1000;
+		current_link_up = 1;
+		if (bmcr & BMCR_FULLDPLX)
+			current_duplex = DUPLEX_FULL;
+		else
+			current_duplex = DUPLEX_HALF;
+
+		if (bmcr & BMCR_ANENABLE) {
+			u32 local_adv, remote_adv, common;
+
+			err |= tg3_readphy(tp, MII_ADVERTISE, &local_adv);
+			err |= tg3_readphy(tp, MII_LPA, &remote_adv);
+			common = local_adv & remote_adv;
+			if (common & (ADVERTISE_1000XHALF |
+				      ADVERTISE_1000XFULL)) {
+				if (common & ADVERTISE_1000XFULL)
+					current_duplex = DUPLEX_FULL;
+				else
+					current_duplex = DUPLEX_HALF;
+
+				tg3_setup_flow_control(tp, local_adv,
+						       remote_adv);
+			}
+			else
+				current_link_up = 0;
+		}
+	}
+
+	tp->mac_mode &= ~MAC_MODE_HALF_DUPLEX;
+	if (tp->link_config.active_duplex == DUPLEX_HALF)
+		tp->mac_mode |= MAC_MODE_HALF_DUPLEX;
+
+	tw32_f(MAC_MODE, tp->mac_mode);
+	udelay(40);
+
+	tw32_f(MAC_EVENT, MAC_EVENT_LNKSTATE_CHANGED);
+
+	tp->link_config.active_speed = current_speed;
+	tp->link_config.active_duplex = current_duplex;
+
+	if (current_link_up != netif_carrier_ok(tp->dev)) {
+		if (current_link_up)
+			netif_carrier_on(tp->dev);
+		else {
+			netif_carrier_off(tp->dev);
+			tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+		}
+		tg3_link_report(tp);
+	}
+	return err;
+}
+
+static void tg3_serdes_parallel_detect(struct tg3 *tp)
+{
+	if (tp->tg3_flags2 & TG3_FLG2_PHY_JUST_INITTED) {
+		/* Give autoneg time to complete. */
+		tp->tg3_flags2 &= ~TG3_FLG2_PHY_JUST_INITTED;
+		return;
+	}
+	if (!netif_carrier_ok(tp->dev) &&
+	    (tp->link_config.autoneg == AUTONEG_ENABLE)) {
+		u32 bmcr;
+
+		tg3_readphy(tp, MII_BMCR, &bmcr);
+		if (bmcr & BMCR_ANENABLE) {
+			u32 phy1, phy2;
+
+			/* Select shadow register 0x1f */
+			tg3_writephy(tp, 0x1c, 0x7c00);
+			tg3_readphy(tp, 0x1c, &phy1);
+
+			/* Select expansion interrupt status register */
+			tg3_writephy(tp, 0x17, 0x0f01);
+			tg3_readphy(tp, 0x15, &phy2);
+			tg3_readphy(tp, 0x15, &phy2);
+
+			if ((phy1 & 0x10) && !(phy2 & 0x20)) {
+				/* We have signal detect and not receiving
+				 * config code words, link is up by parallel
+				 * detection.
+				 */
+
+				bmcr &= ~BMCR_ANENABLE;
+				bmcr |= BMCR_SPEED1000 | BMCR_FULLDPLX;
+				tg3_writephy(tp, MII_BMCR, bmcr);
+				tp->tg3_flags2 |= TG3_FLG2_PARALLEL_DETECT;
+			}
+		}
+	}
+	else if (netif_carrier_ok(tp->dev) &&
+		 (tp->link_config.autoneg == AUTONEG_ENABLE) &&
+		 (tp->tg3_flags2 & TG3_FLG2_PARALLEL_DETECT)) {
+		u32 phy2;
+
+		/* Select expansion interrupt status register */
+		tg3_writephy(tp, 0x17, 0x0f01);
+		tg3_readphy(tp, 0x15, &phy2);
+		if (phy2 & 0x20) {
+			u32 bmcr;
+
+			/* Config code words received, turn on autoneg. */
+			tg3_readphy(tp, MII_BMCR, &bmcr);
+			tg3_writephy(tp, MII_BMCR, bmcr | BMCR_ANENABLE);
+
+			tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+
+		}
+	}
+}
+
 static int tg3_setup_phy(struct tg3 *tp, int force_reset)
 {
 	int err;
 
 	if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) {
 		err = tg3_setup_fiber_phy(tp, force_reset);
+	} else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) {
+		err = tg3_setup_fiber_mii_phy(tp, force_reset);
 	} else {
 		err = tg3_setup_copper_phy(tp, force_reset);
 	}
@@ -4127,6 +4360,9 @@ static int tg3_chip_reset(struct tg3 *tp)
 	if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) {
 		tp->mac_mode = MAC_MODE_PORT_MODE_TBI;
 		tw32_f(MAC_MODE, tp->mac_mode);
+	} else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) {
+		tp->mac_mode = MAC_MODE_PORT_MODE_GMII;
+		tw32_f(MAC_MODE, tp->mac_mode);
 	} else
 		tw32_f(MAC_MODE, 0);
 	udelay(40);
@@ -5911,7 +6147,8 @@ static void tg3_timer(unsigned long __opaque)
 				udelay(40);
 				tg3_setup_phy(tp, 0);
 			}
-		}
+		} else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES)
+			tg3_serdes_parallel_detect(tp);
 
 		tp->timer_counter = tp->timer_multiplier;
 	}
@@ -8615,8 +8852,12 @@ static void __devinit tg3_get_eeprom_hw_cfg(struct tg3 *tp)
 			eeprom_phy_id = 0;
 
 		tp->phy_id = eeprom_phy_id;
-		if (eeprom_phy_serdes)
-			tp->tg3_flags2 |= TG3_FLG2_PHY_SERDES;
+		if (eeprom_phy_serdes) {
+			if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780)
+				tp->tg3_flags2 |= TG3_FLG2_MII_SERDES;
+			else
+				tp->tg3_flags2 |= TG3_FLG2_PHY_SERDES;
+		}
 
 		if (tp->tg3_flags2 & TG3_FLG2_5750_PLUS)
 			led_cfg = cfg2 & (NIC_SRAM_DATA_CFG_LED_MODE_MASK |
@@ -8751,7 +8992,7 @@ static int __devinit tg3_phy_probe(struct tg3 *tp)
 		}
 	}
 
-	if (!(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) &&
+	if (!(tp->tg3_flags2 & TG3_FLG2_ANY_SERDES) &&
 	    !(tp->tg3_flags & TG3_FLAG_ENABLE_ASF)) {
 		u32 bmsr, adv_reg, tg3_ctrl;
 
@@ -8804,7 +9045,7 @@ skip_phy_reset:
 		err = tg3_init_5401phy_dsp(tp);
 	}
 
-	if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES)
+	if (tp->tg3_flags2 & TG3_FLG2_ANY_SERDES)
 		tp->link_config.advertising =
 			(ADVERTISED_1000baseT_Half |
 			 ADVERTISED_1000baseT_Full |
@@ -9153,7 +9394,8 @@ static int __devinit tg3_get_invariants(struct tg3 *tp)
 	if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700) ||
 	    ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5705) &&
 	     (tp->pci_chip_rev_id != CHIPREV_ID_5705_A0) &&
-	     (tp->pci_chip_rev_id != CHIPREV_ID_5705_A1)))
+	     (tp->pci_chip_rev_id != CHIPREV_ID_5705_A1)) ||
+	    (tp->tg3_flags2 & TG3_FLG2_ANY_SERDES))
 		tp->tg3_flags2 |= TG3_FLG2_NO_ETH_WIRE_SPEED;
 
 	if (GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5703_AX ||