Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 "More hardware support across the field including a bunch of device
  drivers.  The highlight however really are further steps towards
  device tree.

  This has been sitting in -next for ages.  All MIPS _defconfigs have
  been tested to boot or where I don't have hardware available, to at
  least build fine."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
  MIPS: Loongson 1B: Add defconfig
  MIPS: Loongson 1B: Add board support
  MIPS: Netlogic: early console fix
  MIPS: Netlogic: Fix indentation of smpboot.S
  MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
  MIPS: Netlogic: Remove unused pcibios_fixups
  MIPS: Netlogic: Add XLP SoC devices in FDT
  MIPS: Netlogic: Add IRQ mappings for more devices
  MIPS: Netlogic: USB support for XLP
  MIPS: Netlogic: XLP PCIe controller support.
  MIPS: Netlogic: Platform changes for XLR/XLS I2C
  MIPS: Netlogic: Platform NAND/NOR flash support
  MIPS: Netlogic: Platform changes for XLS USB
  MIPS: Netlogic: Remove NETLOGIC_ prefix
  MIPS: Netlogic: SMP wakeup code update
  MIPS: Netlogic: Update comments in smpboot.S
  MIPS: BCM63XX: Add 96328avng reference board
  MIPS: Expose PCIe drivers for MIPS
  MIPS: BCM63XX: Add PCIe Support for BCM6328
  MIPS: BCM63XX: Move the PCI initialization into its own function
  ...

1 files changed, 140 insertions, 0 deletions

diff --git a/arch/mips/netlogic/xlr/platform.c b/arch/mips/netlogic/xlr/platform.c
index eab64b45dff..71b44d82621 100644
--- a/arch/mips/netlogic/xlr/platform.c
+++ b/arch/mips/netlogic/xlr/platform.c
@@ -14,6 +14,7 @@
 #include <linux/resource.h>
 #include <linux/serial_8250.h>
 #include <linux/serial_reg.h>
+#include <linux/i2c.h>
 
 #include <asm/netlogic/haldefs.h>
 #include <asm/netlogic/xlr/iomap.h>
@@ -97,3 +98,142 @@ static int __init nlm_uart_init(void)
 }
 
 arch_initcall(nlm_uart_init);
+
+#ifdef CONFIG_USB
+/* Platform USB devices, only on XLS chips */
+static u64 xls_usb_dmamask = ~(u32)0;
+#define USB_PLATFORM_DEV(n, i, irq)					\
+	{								\
+		.name		= n,					\
+		.id		= i,					\
+		.num_resources	= 2,					\
+		.dev		= {					\
+			.dma_mask	= &xls_usb_dmamask,		\
+			.coherent_dma_mask = 0xffffffff,		\
+		},							\
+		.resource	= (struct resource[]) {			\
+			{						\
+				.flags = IORESOURCE_MEM,		\
+			},						\
+			{						\
+				.start	= irq,				\
+				.end	= irq,				\
+				.flags = IORESOURCE_IRQ,		\
+			},						\
+		},							\
+	}
+
+static struct platform_device xls_usb_ehci_device =
+			 USB_PLATFORM_DEV("ehci-xls", 0, PIC_USB_IRQ);
+static struct platform_device xls_usb_ohci_device_0 =
+			 USB_PLATFORM_DEV("ohci-xls-0", 1, PIC_USB_IRQ);
+static struct platform_device xls_usb_ohci_device_1 =
+			 USB_PLATFORM_DEV("ohci-xls-1", 2, PIC_USB_IRQ);
+
+static struct platform_device *xls_platform_devices[] = {
+	&xls_usb_ehci_device,
+	&xls_usb_ohci_device_0,
+	&xls_usb_ohci_device_1,
+};
+
+int xls_platform_usb_init(void)
+{
+	uint64_t usb_mmio, gpio_mmio;
+	unsigned long memres;
+	uint32_t val;
+
+	if (!nlm_chip_is_xls())
+		return 0;
+
+	gpio_mmio = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET);
+	usb_mmio  = nlm_mmio_base(NETLOGIC_IO_USB_1_OFFSET);
+
+	/* Clear Rogue Phy INTs */
+	nlm_write_reg(usb_mmio, 49, 0x10000000);
+	/* Enable all interrupts */
+	nlm_write_reg(usb_mmio, 50, 0x1f000000);
+
+	/* Enable ports */
+	nlm_write_reg(usb_mmio,  1, 0x07000500);
+
+	val = nlm_read_reg(gpio_mmio, 21);
+	if (((val >> 22) & 0x01) == 0) {
+		pr_info("Detected USB Device mode - Not supported!\n");
+		nlm_write_reg(usb_mmio,  0, 0x01000000);
+		return 0;
+	}
+
+	pr_info("Detected USB Host mode - Adding XLS USB devices.\n");
+	/* Clear reset, host mode */
+	nlm_write_reg(usb_mmio,  0, 0x02000000);
+
+	/* Memory resource for various XLS usb ports */
+	usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_0_OFFSET);
+	memres = CPHYSADDR((unsigned long)usb_mmio);
+	xls_usb_ehci_device.resource[0].start = memres;
+	xls_usb_ehci_device.resource[0].end = memres + 0x400 - 1;
+
+	memres += 0x400;
+	xls_usb_ohci_device_0.resource[0].start = memres;
+	xls_usb_ohci_device_0.resource[0].end = memres + 0x400 - 1;
+
+	memres += 0x400;
+	xls_usb_ohci_device_1.resource[0].start = memres;
+	xls_usb_ohci_device_1.resource[0].end = memres + 0x400 - 1;
+
+	return platform_add_devices(xls_platform_devices,
+				ARRAY_SIZE(xls_platform_devices));
+}
+
+arch_initcall(xls_platform_usb_init);
+#endif
+
+#ifdef CONFIG_I2C
+static struct i2c_board_info nlm_i2c_board_info1[] __initdata = {
+	/* All XLR boards have this RTC and Max6657 Temp Chip */
+	[0] = {
+		.type	= "ds1374",
+		.addr	= 0x68
+	},
+	[1] = {
+		.type	= "lm90",
+		.addr	= 0x4c
+	},
+};
+
+static struct resource i2c_resources[] = {
+	[0] = {
+		.start	= 0,	/* filled at init */
+		.end	= 0,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device nlm_xlr_i2c_1 = {
+	.name           = "xlr-i2cbus",
+	.id             = 1,
+	.num_resources	= 1,
+	.resource	= i2c_resources,
+};
+
+static int __init nlm_i2c_init(void)
+{
+	int err = 0;
+	unsigned int offset;
+
+	/* I2C bus 0 does not have any useful devices, configure only bus 1 */
+	offset = NETLOGIC_IO_I2C_1_OFFSET;
+	nlm_xlr_i2c_1.resource[0].start = CPHYSADDR(nlm_mmio_base(offset));
+	nlm_xlr_i2c_1.resource[0].end = nlm_xlr_i2c_1.resource[0].start + 0xfff;
+
+	platform_device_register(&nlm_xlr_i2c_1);
+
+	err = i2c_register_board_info(1, nlm_i2c_board_info1,
+				ARRAY_SIZE(nlm_i2c_board_info1));
+	if (err < 0)
+		pr_err("nlm-i2c: cannot register board I2C devices\n");
+	return err;
+}
+
+arch_initcall(nlm_i2c_init);
+#endif