Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO changes from Linus Walleij:
 "Here is the bulk of GPIO changes for the v3.13 development cycle.

  I've got ACKs for the things that affect other subsystems (or it's my
  own subsystem, like pinctrl).  Most of that pertain to an attempt from
  my side to consolidate and get rid of custom GPIO implementations in
  the ARM tree.  I will continue doing this.

  The main change this time is the new GPIO descriptor API, background
  for this can be found in Corbet's summary from this january in LWN:

    http://lwn.net/Articles/533632/

  Summary:

   - Merged the GPIO descriptor API from Alexandre Courbot.  This is a
     first step toward trying to get rid of the global GPIO numberspace
     for the future.

   - Add an API so that driver can flag that a certain GPIO line is
     being used by a irqchip backend for generating IRQs, so that we can
     enforce checks, like not allowing users to switch that line to an
     output at runtime, since this makes no sense.  Implemented
     corresponding calls in a few select drivers.

   - ACPI GPIO cleanups, refactorings and switch to using the
     descriptor-based interface.

   - Support for the TPS80036 Palmas GPIO variant.

   - A new driver for the Broadcom Kona GPIO SoC IP block.

   - Device tree support for the PCF857x driver.

   - A set of ARM GPIO refactorings with the goal of getting rid of a
     bunch of custom GPIO implementations from the arch/arm/* tree:

     * Move the IOP GPIO driver to the GPIO subsystem and fix all users
       to use the gpiolib API for accessing GPIOs.  Delete the old
       custom GPIO implementation.

     * Delete the unused custom PXA GPIO implemention.

     * Convert all users of the IXP4 custom GPIO implementation to use
       gpiolib and delete the custom implementation.

     * Delete the custom Gemini GPIO implementation, also completely
       unused.

   - Various cleanups and renamings"

* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
  gpio: gpio-mxs: Remove unneeded dt checks
  gpio: pl061: don't depend on CONFIG_ARM
  gpio: bcm-kona: add missing .owner to struct gpio_chip
  gpiolib: provide a declaration of seq_file in gpio/driver.h
  gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
  gpio: provide stubs for devres gpio functions
  gpiolib: devres: add missing headers
  gpiolib: make GPIO_DEVRES depend on GPIOLIB
  gpiolib: devres: fix devm_gpiod_get_index()
  gpiolib / ACPI: document the GPIO descriptor based interface
  gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
  gpiolib / ACPI: add ACPI support for gpiod_get_index()
  gpiolib / ACPI: convert to gpiod interfaces
  gpiolib: add gpiod_get() and gpiod_put() functions
  gpiolib: port of_ functions to use gpiod
  gpiolib: export descriptor-based GPIO interface
  Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
  gpio: bcm281xx: Don't print addresses of GPIO area in probe()
  gpio: tegra: use new gpio_lock_as_irq() API
  gpio: rcar: Include linux/of.h header
  ...

3 files changed, 145 insertions, 4 deletions

diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt
index aca4e69121b..b994bcb32b9 100644
--- a/Documentation/acpi/enumeration.txt
+++ b/Documentation/acpi/enumeration.txt
@@ -295,10 +295,6 @@ These GPIO numbers are controller relative and path "\\_SB.PCI0.GPI0"
 specifies the path to the controller. In order to use these GPIOs in Linux
 we need to translate them to the Linux GPIO numbers.
 
-The driver can do this by including <linux/acpi_gpio.h> and then calling
-acpi_get_gpio(path, gpio). This will return the Linux GPIO number or
-negative errno if there was no translation found.
-
 In a simple case of just getting the Linux GPIO number from device
 resources one can use acpi_get_gpio_by_index() helper function. It takes
 pointer to the device and index of the GpioIo/GpioInt descriptor in the
@@ -322,3 +318,25 @@ suitable to the gpiolib before passing them.
 
 In case of GpioInt resource an additional call to gpio_to_irq() must be
 done before calling request_irq().
+
+Note that the above API is ACPI specific and not recommended for drivers
+that need to support non-ACPI systems. The recommended way is to use
+the descriptor based GPIO interfaces. The above example looks like this
+when converted to the GPIO desc:
+
+	#include <linux/gpio/consumer.h>
+	...
+
+	struct gpio_desc *irq_desc, *power_desc;
+
+	irq_desc = gpiod_get_index(dev, NULL, 1);
+	if (IS_ERR(irq_desc))
+		/* handle error */
+
+	power_desc = gpiod_get_index(dev, NULL, 0);
+	if (IS_ERR(power_desc))
+		/* handle error */
+
+	/* Now we can use the GPIO descriptors */
+
+See also Documentation/gpio.txt.
diff --git a/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt b/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt
new file mode 100644
index 00000000000..4a63bc96b68
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt
@@ -0,0 +1,52 @@
+Broadcom Kona Family GPIO
+=========================
+
+This GPIO driver is used in the following Broadcom SoCs:
+  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+The Broadcom GPIO Controller IP can be configured prior to synthesis to
+support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+GPIO controller only supports edge, not level, triggering of interrupts.
+
+Required properties
+-------------------
+
+- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt outputs from the controller. There is one GPIO
+  interrupt per GPIO bank. The number of interrupts listed depends on the
+  number of GPIO banks on the SoC. The interrupts must be ordered by bank,
+  starting with bank 0. There is always a 1:1 mapping between banks and
+  IRQs.
+- #gpio-cells: Should be <2>. The first cell is the pin number, the second
+  cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+  See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
+- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
+  second cell is used to specify flags. The following subset of flags is
+  supported:
+  - trigger type (bits[1:0]):
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      3 = low-to-high or high-to-low edge triggered
+      Valid values are 1, 2, 3
+  See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
+- gpio-controller: Marks the device node as a GPIO controller.
+- interrupt-controller: Marks the device node as an interrupt controller.
+
+Example:
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x800>;
+		interrupts =
+		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
new file mode 100644
index 00000000000..d63194a2c84
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
@@ -0,0 +1,71 @@
+* PCF857x-compatible I/O expanders
+
+The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be
+driven high by a pull-up current source or driven low to ground. This combines
+the direction and output level into a single bit per line, which can't be read
+back. We can't actually know at initialization time whether a line is configured
+(a) as output and driving the signal low/high, or (b) as input and reporting a
+low/high value, without knowing the last value written since the chip came out
+of reset (if any). The only reliable solution for setting up line direction is
+thus to do it explicitly.
+
+Required Properties:
+
+  - compatible: should be one of the following.
+    - "maxim,max7328": For the Maxim MAX7378
+    - "maxim,max7329": For the Maxim MAX7329
+    - "nxp,pca8574": For the NXP PCA8574
+    - "nxp,pca8575": For the NXP PCA8575
+    - "nxp,pca9670": For the NXP PCA9670
+    - "nxp,pca9671": For the NXP PCA9671
+    - "nxp,pca9672": For the NXP PCA9672
+    - "nxp,pca9673": For the NXP PCA9673
+    - "nxp,pca9674": For the NXP PCA9674
+    - "nxp,pca9675": For the NXP PCA9675
+    - "nxp,pcf8574": For the NXP PCF8574
+    - "nxp,pcf8574a": For the NXP PCF8574A
+    - "nxp,pcf8575": For the NXP PCF8575
+    - "ti,tca9554": For the TI TCA9554
+
+  - reg: I2C slave address.
+
+  - gpio-controller: Marks the device node as a gpio controller.
+  - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
+    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
+    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+
+Optional Properties:
+
+  - lines-initial-states: Bitmask that specifies the initial state of each
+  line. When a bit is set to zero, the corresponding line will be initialized to
+  the input (pulled-up) state. When the  bit is set to one, the line will be
+  initialized the the low-level output state. If the property is not specified
+  all lines will be initialized to the input state.
+
+  The I/O expander can detect input state changes, and thus optionally act as
+  an interrupt controller. When the expander interrupt line is connected all the
+  following properties must be set. For more information please see the
+  interrupt controller device tree bindings documentation available at
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+  - interrupt-controller: Identifies the node as an interrupt controller.
+  - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2.
+  - interrupt-parent: phandle of the parent interrupt controller.
+  - interrupts: Interrupt specifier for the controllers interrupt.
+
+
+Please refer to gpio.txt in this directory for details of the common GPIO
+bindings used by client devices.
+
+Example: PCF8575 I/O expander node
+
+	pcf8575: gpio@20 {
+		compatible = "nxp,pcf8575";
+		reg = <0x20>;
+		interrupt-parent = <&irqpin2>;
+		interrupts = <3 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};