Merge branch 'at91' into devel

32 files changed, 1908 insertions, 142 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
index d187e9f7cf1..1196290082d 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -7,6 +7,12 @@ PIT Timer required properties:
 - interrupts: Should contain interrupt for the PIT which is the IRQ line
   shared across all System Controller members.
 
+System Timer (ST) required properties:
+- compatible: Should be "atmel,at91rm9200-st"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the ST which is the IRQ line
+  shared across all System Controller members.
+
 TC/TCLIB Timer required properties:
 - compatible: Should be "atmel,<chip>-tcb".
   <chip> can be "at91rm9200" or "at91sam9x5"
diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index 20a987e55a2..3a268127b05 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -84,8 +84,13 @@ Required properties for pin configuration node:
   The PERIPH 0 means gpio.
 
 Bits used for CONFIG:
-PULL_UP(1 << 0): indicate this pin need a pull up.
-MULTIDRIVE(1 << 1): indicate this pin need to be configured as multidrive.
+PULL_UP		(1 << 0): indicate this pin need a pull up.
+MULTIDRIVE	(1 << 1): indicate this pin need to be configured as multidrive.
+DEGLITCH	(1 << 2): indicate this pin need deglitch.
+PULL_DOWN	(1 << 3): indicate this pin need a pull down.
+DIS_SCHMIT	(1 << 4): indicate this pin need to disable schmit trigger.
+DEBOUNCE	(1 << 16): indicate this pin need debounce.
+DEBOUNCE_VAL	(0x3fff << 17): debounce val.
 
 NOTE:
 Some requirements for using atmel,at91rm9200-pinctrl binding:
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4ffed9ae729..fb5b07737ca 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1,7 +1,10 @@
 ifeq ($(CONFIG_OF),y)
 
 # Keep at91 dtb files sorted alphabetically for each SoC
+# rm9200
+dtb-$(CONFIG_ARCH_AT91) += at91rm9200ek.dtb
 # sam9260
+dtb-$(CONFIG_ARCH_AT91) += animeo_ip.dtb
 dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb
 dtb-$(CONFIG_ARCH_AT91) += ethernut5.dtb
 dtb-$(CONFIG_ARCH_AT91) += evk-pro3.dtb
@@ -19,6 +22,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
 dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
 # sam9g45
 dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
 # sam9n12
 dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
 # sam9x5
diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/animeo_ip.dts
new file mode 100644
index 00000000000..74d92cd29d8
--- /dev/null
+++ b/arch/arm/boot/dts/animeo_ip.dts
@@ -0,0 +1,178 @@
+/*
+ * animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards
+ *
+ *  Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2 only.
+ */
+
+/dts-v1/;
+/include/ "at91sam9260.dtsi"
+
+/ {
+	model = "Somfy Animeo IP";
+	compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &usart1;
+		serial1 = &usart2;
+		serial2 = &usart0;
+		serial3 = &dbgu;
+		serial4 = &usart3;
+		serial5 = &uart0;
+		serial6 = &uart1;
+	};
+
+	chosen {
+		linux,stdout-path = &usart2;
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+	};
+
+	ahb {
+		apb {
+			usart0: serial@fffb0000 {
+				pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>;
+				linux,rs485-enabled-at-boot-time;
+				status = "okay";
+			};
+
+			usart1: serial@fffb4000 {
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>;
+				linux,rs485-enabled-at-boot-time;
+				status = "okay";
+			};
+
+			usart2: serial@fffb8000 {
+				pinctrl-0 = <&pinctrl_usart2>;
+				status = "okay";
+			};
+
+			macb0: ethernet@fffc4000 {
+				pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>;
+				phy-mode = "mii";
+				status = "okay";
+			};
+
+			mmc0: mmc@fffa8000 {
+				pinctrl-0 = <&pinctrl_mmc0_clk
+					     &pinctrl_mmc0_slot1_cmd_dat0
+					     &pinctrl_mmc0_slot1_dat1_3>;
+				status = "okay";
+
+				slot@1 {
+					reg = <1>;
+					bus-width = <4>;
+				};
+			};
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x8000>;
+			};
+
+			barebox@8000 {
+				label = "barebox";
+				reg = <0x8000 0x40000>;
+			};
+
+			bareboxenv@48000 {
+				label = "bareboxenv";
+				reg = <0x48000 0x8000>;
+			};
+
+			user_block@0x50000 {
+				label = "user_block";
+				reg = <0x50000 0xb0000>;
+			};
+
+			kernel@100000 {
+				label = "kernel";
+				reg = <0x100000 0x1b0000>;
+			};
+
+			root@2b0000 {
+				label = "root";
+				reg = <0x2b0000 0x1D50000>;
+			};
+		};
+
+		usb0: ohci@00500000 {
+			num-ports = <2>;
+			atmel,vbus-gpio = <&pioB 15 1>;
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power_green {
+			label = "power_green";
+			gpios = <&pioC 17 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		power_red {
+			label = "power_red";
+			gpios = <&pioA 2 0>;
+		};
+
+		tx_green {
+			label = "tx_green";
+			gpios = <&pioC 19 0>;
+		};
+
+		tx_red {
+			label = "tx_red";
+			gpios = <&pioC 18 0>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		keyswitch_in {
+			label = "keyswitch_in";
+			gpios = <&pioB 1 0>;
+			linux,code = <28>;
+			gpio-key,wakeup;
+		};
+
+		error_in {
+			label = "error_in";
+			gpios = <&pioB 2 0>;
+			linux,code = <29>;
+			gpio-key,wakeup;
+		};
+
+		btn {
+			label = "btn";
+			gpios = <&pioC 23 0>;
+			linux,code = <31>;
+			gpio-key,wakeup;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
new file mode 100644
index 00000000000..e154f242c68
--- /dev/null
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -0,0 +1,349 @@
+/*
+ * at91rm9200.dtsi - Device Tree Include file for AT91RM9200 family SoC
+ *
+ *  Copyright (C) 2011 Atmel,
+ *                2011 Nicolas Ferre <nicolas.ferre@atmel.com>,
+ *                2012 Joachim Eastwood <manabian@gmail.com>
+ *
+ * Based on at91sam9260.dtsi
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	model = "Atmel AT91RM9200 family SoC";
+	compatible = "atmel,at91rm9200";
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		serial1 = &usart0;
+		serial2 = &usart1;
+		serial3 = &usart2;
+		serial4 = &usart3;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+		tcb0 = &tcb0;
+		tcb1 = &tcb1;
+	};
+	cpus {
+		cpu@0 {
+			compatible = "arm,arm920t";
+		};
+	};
+
+	memory {
+		reg = <0x20000000 0x04000000>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			aic: interrupt-controller@fffff000 {
+				#interrupt-cells = <3>;
+				compatible = "atmel,at91rm9200-aic";
+				interrupt-controller;
+				reg = <0xfffff000 0x200>;
+				atmel,external-irqs = <25 26 27 28 29 30 31>;
+			};
+
+			ramc0: ramc@ffffff00 {
+				compatible = "atmel,at91rm9200-sdramc";
+				reg = <0xffffff00 0x100>;
+			};
+
+			pmc: pmc@fffffc00 {
+				compatible = "atmel,at91rm9200-pmc";
+				reg = <0xfffffc00 0x100>;
+			};
+
+			st: timer@fffffd00 {
+				compatible = "atmel,at91rm9200-st";
+				reg = <0xfffffd00 0x100>;
+				interrupts = <1 4 7>;
+			};
+
+			tcb0: timer@fffa0000 {
+				compatible = "atmel,at91rm9200-tcb";
+				reg = <0xfffa0000 0x100>;
+				interrupts = <17 4 0 18 4 0 19 4 0>;
+			};
+
+			tcb1: timer@fffa4000 {
+				compatible = "atmel,at91rm9200-tcb";
+				reg = <0xfffa4000 0x100>;
+				interrupts = <20 4 0 21 4 0 22 4 0>;
+			};
+
+			pinctrl@fffff400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				ranges = <0xfffff400 0xfffff400 0x800>;
+
+				atmel,mux-mask = <
+					/*    A         B     */
+					 0xffffffff 0xffffffff  /* pioA */
+					 0xffffffff 0x083fffff  /* pioB */
+					 0xffff3fff 0x00000000  /* pioC */
+					 0x03ff87ff 0x0fffff80  /* pioD */
+					>;
+
+				/* shared pinctrl settings */
+				dbgu {
+					pinctrl_dbgu: dbgu-0 {
+						atmel,pins =
+							<0 30 0x1 0x0	/* PA30 periph A */
+							 0 31 0x1 0x1>;	/* PA31 periph with pullup */
+					};
+				};
+
+				uart0 {
+					pinctrl_uart0: uart0-0 {
+						atmel,pins =
+							<0 17 0x1 0x0	/* PA17 periph A */
+							 0 18 0x1 0x0>;	/* PA18 periph A */
+					};
+
+					pinctrl_uart0_rts: uart0_rts-0 {
+						atmel,pins =
+							<0 20 0x1 0x0>;	/* PA20 periph A */
+					};
+
+					pinctrl_uart0_cts: uart0_cts-0 {
+						atmel,pins =
+							<0 21 0x1 0x0>;	/* PA21 periph A */
+					};
+				};
+
+				uart1 {
+					pinctrl_uart1: uart1-0 {
+						atmel,pins =
+							<1 20 0x1 0x1	/* PB20 periph A with pullup */
+							 1 21 0x1 0x0>;	/* PB21 periph A */
+					};
+
+					pinctrl_uart1_rts: uart1_rts-0 {
+						atmel,pins =
+							<1 24 0x1 0x0>;	/* PB24 periph A */
+					};
+
+					pinctrl_uart1_cts: uart1_cts-0 {
+						atmel,pins =
+							<1 26 0x1 0x0>;	/* PB26 periph A */
+					};
+
+					pinctrl_uart1_dtr_dsr: uart1_dtr_dsr-0 {
+						atmel,pins =
+							<1 19 0x1 0x0	/* PB19 periph A */
+							 1 25 0x1 0x0>;	/* PB25 periph A */
+					};
+
+					pinctrl_uart1_dcd: uart1_dcd-0 {
+						atmel,pins =
+							<1 23 0x1 0x0>;	/* PB23 periph A */
+					};
+
+					pinctrl_uart1_ri: uart1_ri-0 {
+						atmel,pins =
+							<1 18 0x1 0x0>;	/* PB18 periph A */
+					};
+				};
+
+				uart2 {
+					pinctrl_uart2: uart2-0 {
+						atmel,pins =
+							<0 22 0x1 0x0	/* PA22 periph A */
+							 0 23 0x1 0x1>;	/* PA23 periph A with pullup */
+					};
+
+					pinctrl_uart2_rts: uart2_rts-0 {
+						atmel,pins =
+							<0 30 0x2 0x0>;	/* PA30 periph B */
+					};
+
+					pinctrl_uart2_cts: uart2_cts-0 {
+						atmel,pins =
+							<0 31 0x2 0x0>;	/* PA31 periph B */
+					};
+				};
+
+				uart3 {
+					pinctrl_uart3: uart3-0 {
+						atmel,pins =
+							<0 5 0x2 0x1	/* PA5 periph B with pullup */
+							 0 6 0x2 0x0>;	/* PA6 periph B */
+					};
+
+					pinctrl_uart3_rts: uart3_rts-0 {
+						atmel,pins =
+							<1 0 0x2 0x0>;	/* PB0 periph B */
+					};
+
+					pinctrl_uart3_cts: uart3_cts-0 {
+						atmel,pins =
+							<1 1 0x2 0x0>;	/* PB1 periph B */
+					};
+				};
+
+				nand {
+					pinctrl_nand: nand-0 {
+						atmel,pins =
+							<2 2 0x0 0x1	/* PC2 gpio RDY pin pull_up */
+							 1 1 0x0 0x1>;	/* PB1 gpio CD pin pull_up */
+					};
+				};
+
+				pioA: gpio@fffff400 {
+					compatible = "atmel,at91rm9200-gpio";
+					reg = <0xfffff400 0x200>;
+					interrupts = <2 4 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				pioB: gpio@fffff600 {
+					compatible = "atmel,at91rm9200-gpio";
+					reg = <0xfffff600 0x200>;
+					interrupts = <3 4 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				pioC: gpio@fffff800 {
+					compatible = "atmel,at91rm9200-gpio";
+					reg = <0xfffff800 0x200>;
+					interrupts = <4 4 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				pioD: gpio@fffffa00 {
+					compatible = "atmel,at91rm9200-gpio";
+					reg = <0xfffffa00 0x200>;
+					interrupts = <5 4 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+			};
+
+			dbgu: serial@fffff200 {
+				compatible = "atmel,at91rm9200-usart";
+				reg = <0xfffff200 0x200>;
+				interrupts = <1 4 7>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_dbgu>;
+				status = "disabled";
+			};
+
+			usart0: serial@fffc0000 {
+				compatible = "atmel,at91rm9200-usart";
+				reg = <0xfffc0000 0x200>;
+				interrupts = <6 4 5>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart0>;
+				status = "disabled";
+			};
+
+			usart1: serial@fffc4000 {
+				compatible = "atmel,at91rm9200-usart";
+				reg = <0xfffc4000 0x200>;
+				interrupts = <7 4 5>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1>;
+				status = "disabled";
+			};
+
+			usart2: serial@fffc8000 {
+				compatible = "atmel,at91rm9200-usart";
+				reg = <0xfffc8000 0x200>;
+				interrupts = <8 4 5>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart2>;
+				status = "disabled";
+			};
+
+			usart3: serial@fffcc000 {
+				compatible = "atmel,at91rm9200-usart";
+				reg = <0xfffcc000 0x200>;
+				interrupts = <23 4 5>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart3>;
+				status = "disabled";
+			};
+
+			usb1: gadget@fffb0000 {
+				compatible = "atmel,at91rm9200-udc";
+				reg = <0xfffb0000 0x4000>;
+				interrupts = <11 4 2>;
+				status = "disabled";
+			};
+		};
+
+		nand0: nand@40000000 {
+			compatible = "atmel,at91rm9200-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x40000000 0x10000000>;
+			atmel,nand-addr-offset = <21>;
+			atmel,nand-cmd-offset = <22>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_nand>;
+			nand-ecc-mode = "soft";
+			gpios = <&pioC 2 0
+				 0
+				 &pioB 1 0
+				>;
+			status = "disabled";
+		};
+
+		usb0: ohci@00300000 {
+			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+			reg = <0x00300000 0x100000>;
+			interrupts = <23 4 2>;
+			status = "disabled";
+		};
+	};
+
+	i2c@0 {
+		compatible = "i2c-gpio";
+		gpios = <&pioA 23 0 /* sda */
+			 &pioA 24 0 /* scl */
+			>;
+		i2c-gpio,sda-open-drain;
+		i2c-gpio,scl-open-drain;
+		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
new file mode 100644
index 00000000000..8aa48931e0a
--- /dev/null
+++ b/arch/arm/boot/dts/at91rm9200ek.dts
@@ -0,0 +1,79 @@
+/*
+ * at91rm9200ek.dts - Device Tree file for Atmel AT91RM9200 evaluation kit
+ *
+ *  Copyright (C) 2012 Joachim Eastwood <manabian@gmail.com>
+ *
+ * Licensed under GPLv2 only
+ */
+/dts-v1/;
+/include/ "at91rm9200.dtsi"
+
+/ {
+	model = "Atmel AT91RM9200 evaluation kit";
+	compatible = "atmel,at91rm9200ek", "atmel,at91rm9200";
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+	};
+
+	ahb {
+		apb {
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			usart1: serial@fffc4000 {
+				pinctrl-0 =
+						<&pinctrl_uart1
+						 &pinctrl_uart1_rts
+						 &pinctrl_uart1_cts
+						 &pinctrl_uart1_dtr_dsr
+						 &pinctrl_uart1_dcd
+						 &pinctrl_uart1_ri>;
+				status = "okay";
+			};
+
+			usb1: gadget@fffb0000 {
+				atmel,vbus-gpio = <&pioD 4 0>;
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@00300000 {
+			num-ports = <2>;
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		ds2 {
+			label = "green";
+			gpios = <&pioB 0 0x1>;
+			linux,default-trigger = "mmc0";
+		};
+
+		ds4 {
+			label = "yellow";
+			gpios = <&pioB 1 0x1>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		ds6 {
+			label = "red";
+			gpios = <&pioB 2 0x1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index 9a24ffbb723..b1d3fab60e0 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -21,8 +21,8 @@
 		serial2 = &usart1;
 		serial3 = &usart2;
 		serial4 = &usart3;
-		serial5 = &usart4;
-		serial6 = &usart5;
+		serial5 = &uart0;
+		serial6 = &uart1;
 		gpio0 = &pioA;
 		gpio1 = &pioB;
 		gpio2 = &pioC;
@@ -120,88 +120,104 @@
 					};
 				};
 
-				uart0 {
-					pinctrl_uart0: uart0-0 {
+				usart0 {
+					pinctrl_usart0: usart0-0 {
 						atmel,pins =
 							<1 4 0x1 0x0	/* PB4 periph A */
 							 1 5 0x1 0x0>;	/* PB5 periph A */
 					};
 
-					pinctrl_uart0_rts_cts: uart0_rts_cts-0 {
+					pinctrl_usart0_rts: usart0_rts-0 {
 						atmel,pins =
-							<1 26 0x1 0x0	/* PB26 periph A */
-							 1 27 0x1 0x0>;	/* PB27 periph A */
+							<1 26 0x1 0x0>;	/* PB26 periph A */
 					};
 
-					pinctrl_uart0_dtr_dsr: uart0_dtr_dsr-0 {
+					pinctrl_usart0_cts: usart0_cts-0 {
+						atmel,pins =
+							<1 27 0x1 0x0>;	/* PB27 periph A */
+					};
+
+					pinctrl_usart0_dtr_dsr: usart0_dtr_dsr-0 {
 						atmel,pins =
 							<1 24 0x1 0x0	/* PB24 periph A */
 							 1 22 0x1 0x0>;	/* PB22 periph A */
 					};
 
-					pinctrl_uart0_dcd: uart0_dcd-0 {
+					pinctrl_usart0_dcd: usart0_dcd-0 {
 						atmel,pins =
 							<1 23 0x1 0x0>;	/* PB23 periph A */
 					};
 
-					pinctrl_uart0_ri: uart0_ri-0 {
+					pinctrl_usart0_ri: usart0_ri-0 {
 						atmel,pins =
 							<1 25 0x1 0x0>;	/* PB25 periph A */
 					};
 				};
 
-				uart1 {
-					pinctrl_uart1: uart1-0 {
+				usart1 {
+					pinctrl_usart1: usart1-0 {
 						atmel,pins =
 							<2 6 0x1 0x1	/* PB6 periph A with pullup */
 							 2 7 0x1 0x0>;	/* PB7 periph A */
 					};
 
-					pinctrl_uart1_rts_cts: uart1_rts_cts-0 {
+					pinctrl_usart1_rts: usart1_rts-0 {
 						atmel,pins =
-							<1 28 0x1 0x0	/* PB28 periph A */
-							 1 29 0x1 0x0>;	/* PB29 periph A */
+							<1 28 0x1 0x0>;	/* PB28 periph A */
+					};
+
+					pinctrl_usart1_cts: usart1_cts-0 {
+						atmel,pins =
+							<1 29 0x1 0x0>;	/* PB29 periph A */
 					};
 				};
 
-				uart2 {
-					pinctrl_uart2: uart2-0 {
+				usart2 {
+					pinctrl_usart2: usart2-0 {
 						atmel,pins =
 							<1 8 0x1 0x1	/* PB8 periph A with pullup */
 							 1 9 0x1 0x0>;	/* PB9 periph A */
 					};
 
-					pinctrl_uart2_rts_cts: uart2_rts_cts-0 {
+					pinctrl_usart2_rts: usart2_rts-0 {
 						atmel,pins =
-							<0 4 0x1 0x0	/* PA4 periph A */
-							 0 5 0x1 0x0>;	/* PA5 periph A */
+							<0 4 0x1 0x0>;	/* PA4 periph A */
+					};
+
+					pinctrl_usart2_cts: usart2_cts-0 {
+						atmel,pins =
+							<0 5 0x1 0x0>;	/* PA5 periph A */
 					};
 				};
 
-				uart3 {
-					pinctrl_uart3: uart3-0 {
+				usart3 {
+					pinctrl_usart3: usart3-0 {
 						atmel,pins =
 							<2 10 0x1 0x1	/* PB10 periph A with pullup */
 							 2 11 0x1 0x0>;	/* PB11 periph A */
 					};
 
-					pinctrl_uart3_rts_cts: uart3_rts_cts-0 {
+					pinctrl_usart3_rts: usart3_rts-0 {
+						atmel,pins =
+							<3 8 0x2 0x0>;	/* PB8 periph B */
+					};
+
+					pinctrl_usart3_cts: usart3_cts-0 {
 						atmel,pins =
-							<3 8 0x2 0x0	/* PB8 periph B */
-							 3 10 0x2 0x0>;	/* PB10 periph B */
+							<3 10 0x2 0x0>;	/* PB10 periph B */
 					};
 				};
 
-				uart4 {
-					pinctrl_uart4: uart4-0 {
+				uart0 {
+					pinctrl_uart0: uart0-0 {
 						atmel,pins =
 							<0 31 0x2 0x1	/* PA31 periph B with pullup */
 							 0 30 0x2 0x0>;	/* PA30 periph B */
 					};
 				};
 
-				uart5 {
-					pinctrl_uart5: uart5-0 {
+				uart1 {
+					pinctrl_uart1: uart1-0 {
 						atmel,pins =
 							<2 12 0x1 0x1	/* PB12 periph A with pullup */
 							 2 13 0x1 0x0>;	/* PB13 periph A */
@@ -216,6 +232,79 @@
 					};
 				};
 
+				macb {
+					pinctrl_macb_rmii: macb_rmii-0 {
+						atmel,pins =
+							<0 12 0x1 0x0	/* PA12 periph A */
+							 0 13 0x1 0x0	/* PA13 periph A */
+							 0 14 0x1 0x0	/* PA14 periph A */
+							 0 15 0x1 0x0	/* PA15 periph A */
+							 0 16 0x1 0x0	/* PA16 periph A */
+							 0 17 0x1 0x0	/* PA17 periph A */
+							 0 18 0x1 0x0	/* PA18 periph A */
+							 0 19 0x1 0x0	/* PA19 periph A */
+							 0 20 0x1 0x0	/* PA20 periph A */
+							 0 21 0x1 0x0>;	/* PA21 periph A */
+					};
+
+					pinctrl_macb_rmii_mii: macb_rmii_mii-0 {
+						atmel,pins =
+							<0 22 0x2 0x0	/* PA22 periph B */
+							 0 23 0x2 0x0	/* PA23 periph B */
+							 0 24 0x2 0x0	/* PA24 periph B */
+							 0 25 0x2 0x0	/* PA25 periph B */
+							 0 26 0x2 0x0	/* PA26 periph B */
+							 0 27 0x2 0x0	/* PA27 periph B */
+							 0 28 0x2 0x0	/* PA28 periph B */
+							 0 29 0x2 0x0>;	/* PA29 periph B */
+					};
+
+					pinctrl_macb_rmii_mii_alt: macb_rmii_mii-1 {
+						atmel,pins =
+							<0 10 0x2 0x0	/* PA10 periph B */
+							 0 11 0x2 0x0	/* PA11 periph B */
+							 0 24 0x2 0x0	/* PA24 periph B */
+							 0 25 0x2 0x0	/* PA25 periph B */
+							 0 26 0x2 0x0	/* PA26 periph B */
+							 0 27 0x2 0x0	/* PA27 periph B */
+							 0 28 0x2 0x0	/* PA28 periph B */
+							 0 29 0x2 0x0>;	/* PA29 periph B */
+					};
+				};
+
+				mmc0 {
+					pinctrl_mmc0_clk: mmc0_clk-0 {
+						atmel,pins =
+							<0 8 0x1 0x0>;	/* PA8 periph A */
+					};
+
+					pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 {
+						atmel,pins =
+							<0 7 0x1 0x1	/* PA7 periph A with pullup */
+							 0 6 0x1 0x1>;	/* PA6 periph A with pullup */
+					};
+
+					pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 {
+						atmel,pins =
+							<0 9 0x1 0x1	/* PA9 periph A with pullup */
+							 0 10 0x1 0x1	/* PA10 periph A with pullup */
+							 0 11 0x1 0x1>;	/* PA11 periph A with pullup */
+					};
+
+					pinctrl_mmc0_slot1_cmd_dat0: mmc0_slot1_cmd_dat0-0 {
+						atmel,pins =
+							<0 1 0x2 0x1	/* PA1 periph B with pullup */
+							 0 0 0x2 0x1>;	/* PA0 periph B with pullup */
+					};
+
+					pinctrl_mmc0_slot1_dat1_3: mmc0_slot1_dat1_3-0 {
+						atmel,pins =
+							<0 5 0x2 0x1	/* PA5 periph B with pullup */
+							 0 4 0x2 0x1	/* PA4 periph B with pullup */
+							 0 3 0x2 0x1>;	/* PA3 periph B with pullup */
+					};
+				};
+
 				pioA: gpio@fffff400 {
 					compatible = "atmel,at91rm9200-gpio";
 					reg = <0xfffff400 0x200>;
@@ -263,7 +352,7 @@
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_uart0>;
+				pinctrl-0 = <&pinctrl_usart0>;
 				status = "disabled";
 			};
 
@@ -274,7 +363,7 @@
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_uart1>;
+				pinctrl-0 = <&pinctrl_usart1>;
 				status = "disabled";
 			};
 
@@ -285,7 +374,7 @@
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_uart2>;
+				pinctrl-0 = <&pinctrl_usart2>;
 				status = "disabled";
 			};
 
@@ -296,29 +385,29 @@
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_uart3>;
+				pinctrl-0 = <&pinctrl_usart3>;
 				status = "disabled";
 			};
 
-			usart4: serial@fffd4000 {
+			uart0: serial@fffd4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd4000 0x200>;
 				interrupts = <24 4 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;